2ecb124e42
Fix trailing whitespace
6 years ago
f56968ba0b
New Continuous Filament Mixer ( #12098 )
6 years ago
2d2cd628c6
Update German language ( #12094 )
6 years ago
84b59d58fb
Clean up whitespace
6 years ago
06e2afe8e0
[2.0.x] Reduce HOMING_FEEDRATE_XY for Ender 3 ( #12105 )
...
Homing on the Ender 3 with HOMING_FEEDRATE_XY set to 50*60 was shown (#12074 ) to cause the end-stop micro-switches to bottom out, causing the carriage for both X and Y axis to physically crash into the micro switch. Reducing the homing speed prevents the switches from bottoming out.
6 years ago
af939c158a
Option for G0 to have a separate feedrate ( #12089 )
6 years ago
e5b4bf22d4
Remove debug output from flash persistent store implementation
6 years ago
42fb7c14b0
Update the sdcard usb sharing config and apply to Re-ARM
6 years ago
254b68fe2c
servo update
6 years ago
870bfd08f5
usb and sdcard sharing improvements
...
* Add traceback after watchdog timeout
Add the cpability to perform a traceback following a watchdog timeout.
* Enhanced hardware SPI
Allow use of either SSP0 or SSP1.
Ensure that no data is left in I/O buffers after calls to enable sharing of SSP hardware.
* Make flash emulation of eeprom the default
Make use of flash for eeprom storage the default. This means that usage of eeprom will not cause USB drive mount/unmount operations.
* Allow sharing of SD card
SD card I/O operations from the USB stack take place in idle loop, rather than at interrupt time. Allowing sharing of the SPI bus.
New configuration options to allow usage of the SD card to be specified.
* Fix problem with hardware SPI pins
6 years ago
5ddf52d58e
[HAL][LPC176x] Pull out framework into separate repository
...
Framework and build platform now located at https://github.com/p3p/pio-framework-arduino-lpc176x and https://github.com/p3p/pio-nxplpc-arduino-lpc176x respectively
fix mkssbase leds
move hardware serial
remove hardware/software serial
Hardware Serial extraction
HardwareSerial ISRs
fix disabled serial2 causing Serial object to link
move usb devices out to framework
separate out adc/pwm peripheral function from hal.cpp
fix includes
remove unused pwm init
move adc
HAL header update
templated filtered adc
LPC1769 platform
6 years ago
213e94bce2
[2.0.x] Updated slovak translation ( #12059 )
6 years ago
a40458405a
Fix datasize error when FWRETRACT is disabled ( #12086 )
6 years ago
951b25163e
Extend M217 with configurable park/raise ( #12076 )
6 years ago
ea13a77dcb
Fixed Z-Probes NO/NC for Anycubic Kossel ( #12083 )
6 years ago
ab9d5eb38d
Add Bootscreen Animation ( #12077 )
6 years ago
26208a5c2f
Clean up some boot screens
6 years ago
9b6be0ae0f
Fix lite status screen SD %
6 years ago
af3bf6c956
Tweak config spacing
6 years ago
a44ef27897
Outdent singlenozzle toolchange code
6 years ago
d338e4d875
Fix singlenozzle toolchange cold extrusion test
6 years ago
25b980dddb
Remove erroneous Pin 12 definition
...
There is no switchable Power Supply. Don't put it on Pin 12.
(Pin 12 is actually FAN1)
6 years ago
ddaef1a60c
Clean trailing whitespace
6 years ago
1407afad73
Move SENSITIVE_PINS to its own file
6 years ago
45e738876a
Add stepper MS3 support
...
Co-Authored-By: TheLongAndOnly <thelongandonly@users.noreply.github.com>
6 years ago
d43d4e4219
Refactor PRINTER_EVENT_LEDS, apply to M303 ( #12038 )
...
Co-Authored-By: Giuliano Zaro <gmagician@users.noreply.github.com>
6 years ago
d8d76cd2ba
[2.0.x] Italian language update ( #12060 )
6 years ago
e8d2cf4fb5
EEPROM followup (tmc_stepper_current_t)
6 years ago
50cbca4c55
Hide some menu items when busy
6 years ago
3cb5517ddb
Make singlenozzle tool-change honor no_move ( #12056 )
...
...Set no move earlier so it applies
6 years ago
d332fcb8fa
Fix firmware-retract compile errors ( #12061 )
6 years ago
43940d59ed
Fix trailing spaces
6 years ago
b2c1cd7eda
Allow cold change of active extruder ( #12055 )
...
Followup to #11994
6 years ago
d556dc1865
Fix and improve EEPROM storage ( #12054 )
...
* Clean up Temperature PID
* Improve EEPROM read/write/validate
* Group `SINGLENOZZLE` saved settings
* Group planner saved settings
* Group filament change saved settings
* Group skew saved settings
* Group `FWRETRACT` saved settings
6 years ago
9b5c1a5e77
Fix EEPROM checksum bug
...
Addressing #12048
6 years ago
272d4a5167
Apply #pragma once
6 years ago
07d33849b0
Fix unused var warning, apply ENABLED
6 years ago
a3e8cb1e44
[2.0.x] Ender-4 small improvements in Configuration ( #11843 )
6 years ago
cf5284cdf2
Add SD Firmware Update capability ( #12043 )
...
Co-Authored-By: timoxd7 <timoxd7@users.noreply.github.com>
6 years ago
0bd54392b7
Use uint8_t in EEPROM code
6 years ago
ce82015d5f
Fix include in G80
6 years ago
cef1de89d0
Fixed incorrect axis index. ( #12051 )
6 years ago
d6d48e63fb
Allow #defined TYPE arg to ultralcd menu macros ( #12041 )
...
Previously, it was not possible for the TYPE argument to ultralcd menu macros to itself be a #defined value. This made it difficult to create variables to set many related menu items to a common precision that could be easily changed.
6 years ago
2ef7175b42
Update Ender-2 BED_MAXTEMP ( #12042 )
...
Also added details to the README to make sure the Ender-2 status is properly documented.
6 years ago
5f6aabccbe
Tweak M48 spacing
6 years ago
ec9aa4f468
[2.0.x] Miscellaneous fixes ( #12039 )
...
* Allow override of soft SPI pins in `pins_*.h`
* Add default case to avoid compiler warning.
* Additional pin definitions for Archim 2.
* Einsy Retro has same timings as Einsy Rambo.
6 years ago
906a24fa81
Extensible user interface API ( #11193 )
6 years ago
ee253991d4
Various fixups for single-nozzle filament swap ( #12036 )
6 years ago
55e810d512
Fix G80 compilation
6 years ago
d5017e2788
Add status screen with 4 nozzles
6 years ago
7db0113b53
Improve E_AXIS_N macro
6 years ago
191df5e17d
Correct PWM_PIN behavior for STM32 HALs ( #12027 )
6 years ago
f2ecf8d510
Add option to control Solenoids under PARKING_EXTRUDER ( #12028 )
6 years ago
74cd6cb4fc
Single nozzle filament change ( #11994 )
6 years ago
bfcf570d68
Try ISR_ALIASOF for Endstop Interrupts
6 years ago
c0d9058e25
Shorten an Italian menu title ( #12034 )
...
…and change a multi-use "back" menu item.
6 years ago
dffb4c63dc
[2.0.x] TMC2660 followup ( #12029 )
...
* Don't react to s2g on TMC2660. False positives
* Init with sensorless probing as well
6 years ago
d6b0fbd771
Use uint8_t for all fan speeds ( #12032 )
6 years ago
cb7844c8d4
Save PROGMEM on serial prefixes ( #12033 )
...
With default config and `EEPROM_SETTINGS`, saves over 200 bytes of PROGMEM.
6 years ago
07db08e39d
Fix EXTRUDER_AUTO_FAN_SPEED comment
6 years ago
ca0e308105
Fix up some units comments
6 years ago
65b8f3821b
Suppress temperature.h compile warning
6 years ago
c447d75916
Add support for TMC2660 ( #11998 )
6 years ago
cf0b9eb37c
no need to use destination in do_pause_e_move
6 years ago
e8d677620c
Use NUM_SERVOS in EEPROM code
...
Fix #12015
6 years ago
0fcdfdeed6
Followup to #12017
6 years ago
acac2adfc8
Add support for MeCreator2 ( #12017 )
6 years ago
49823a4939
Fix broken jerk handling ( #12019 )
...
Fix #12004
6 years ago
52a37913c1
Extend and apply some corrections
6 years ago
77b9a41f1f
Add G-code extensions to example configs
6 years ago
e09c144674
Add CNC-like G-code options
6 years ago
33056046a3
STM32 non-generic PWM_PIN and USEABLE_HARDWARE_PWM ( #12016 )
6 years ago
d5141c4e03
Fix up leading/trailing whitespace
6 years ago
65b36642f8
Fix Anycubic Kossel config
6 years ago
fc326b3dde
Add USB_FLASH_DRIVE_SUPPORT to examples
...
Co-Authored-By: marcio-ao <marcio@alephobjects.com>
6 years ago
2067619a26
Add USB_FLASH_DRIVE_SUPPORT
6 years ago
07fe8d28be
[2.0.x] Partial Italian revert ( #12008 )
...
- Use a comma for decimals just in one message has not been a good idea.
- Full comments translation
6 years ago
517b4f4cd4
Fix lightweight UI hotends display
6 years ago
72a750e0eb
[2.0.x] Update Italian language ( #11996 )
6 years ago
bb561baf9e
Tweak some config comments
6 years ago
fcf6d127fd
STM32 timer simplification ( #11995 )
...
Prescalers aren't calculated for the given target frequency.
Stepper timer should run at 2 Mhz and temperature timer at 72 Khz.
6 years ago
8daadd2c8c
Fix TMC_DEBUG undefined report_tmc_status ( #11993 )
6 years ago
c40ea1f0fd
Update EEPROM_VERSION
...
And set EEPROM_OFFSET to 0, since the historical 100 skipped bytes are never used.
6 years ago
1358bd9319
Make MAX_EXTRUDERS always 6
6 years ago
001f26b642
Template struct simplification for serial ( #11990 )
6 years ago
348004c34f
STM32F7 HAL using the official STM32 Arduino Core ( #11750 )
6 years ago
3e58b3a5d4
Followup to #11943
6 years ago
c3229e1b34
Migrate to a new TMC library ( #11943 )
6 years ago
2abf3d258d
Korean language translation support ( #11987 )
6 years ago
d6955f25b2
Expand serial support in DUE/AVR hals exploiting the templated MarlinSerial classes ( #11988 )
6 years ago
f6f2246f59
Templatized serial classes ( #11982 )
6 years ago
ee53f7d813
Revert header reorg.
6 years ago
d619ba2685
Tweak STM32F4 config
6 years ago
d777cef837
fixed minimum macro ( #11986 )
6 years ago
e3f7b69105
Add PROBING_STEPPERS_OFF ( #11984 )
...
Co-Authored-By: houseofbugs <houseofbugs@gmail.com>
6 years ago
0e5bcdf695
Make DISABLE_INACTIVE_EXTRUDER a simple switch
6 years ago
0dedb3e139
Reorganize some core headers ( #11983 )
6 years ago
ab4549d2bc
[2.0.x] Add simultaneous retraction for mixing extruder ( #11941 )
6 years ago
c75f5a376b
Tweak some comments
6 years ago
f4c625d3a1
Ensure MIN/MAX overrides
6 years ago
3019713402
Reorganize some enums
6 years ago
606a4362b3
Reduce STM32F4 compile warnings
6 years ago
b3154b2120
Apply MOVE_Z_WHEN_IDLE to example configurations
...
Co-Authored-By: dot-bob <gibben@gmail.com>
6 years ago
b0fd8f2d74
Add option to move Z on double-click when idle
6 years ago
389376c40e
Clean up softspi.h
6 years ago
e78bdd654d
Clean up BABYSTEP options
6 years ago
8ae113ff36
Show zprobe_zoffset when BABYSTEP_HOTEND_Z_OFFSET is disabled ( #11973 )
6 years ago
2e98437392
Clean up main menu ( #11972 )
6 years ago
6d862b2916
Home before level corners, if needed ( #11976 )
...
…and add a consistent homing screen for all LCD pre-homing.
6 years ago
11ac75edcb
Use PGM_P for PSTR pointers ( #11977 )
6 years ago
4d5566a6b7
Add filament runout sensor menu item ( #11971 )
6 years ago
8489673cea
Adjust some HAL formatting
6 years ago
fb8a07660a
Followup to minmax patch
...
Co-Authored-By: Palatis <palatis@gmail.com>
6 years ago
3c40933713
Remove trailing spaces, old comment
6 years ago
a3ec805c97
Anycubic Kossel Linear+: corrected DELTA_DIAGONAL_ROD ( #11964 )
6 years ago
b30ca652ae
Replace MIN# / MAX# with variadic MIN / MAX ( #11960 )
6 years ago
e10f730478
Tweak vector_3::apply_rotation
6 years ago
e2ab78d876
Fix SERIAL_PORT_2 sanity check
6 years ago
a644d8cb93
Avoid copies in vector and matrix ( #11959 )
6 years ago
693865a649
Fix some whitespace
6 years ago
9903305dda
Merge pull request #9582 from tcm0116/2.0.x-sensorless_probing
...
[2.0.x] Add TMC2130 sensorless probing
6 years ago
14df753086
Correction for block->mix_steps
...
Fix #11484
6 years ago
2ecfda80ac
Improve support for JTAG/SWD pins reuse ( #11963 )
...
STM32 can reuse JTAG and SWD pins separately. Add `DISABLE_DEBUG` option to disable both interfaces and retain `DISABLE_JTAG` to disable JTAG only.
6 years ago
bb47009656
Apply sensorless changes to example configs
6 years ago
3286325044
Add TMC2130 sensorless probing
6 years ago
7d5c336c56
Corrections for dylsexic TMC
6 years ago
d89d8fe852
Fix Busy State in temperature.cpp
...
Fix #11954
6 years ago
70e7a465d8
[2.0.x] Fix compile error ( #11951 )
...
Fix compile error intruduced with M109 modification
6 years ago
935b120949
Anycubic Kossel: probe closer to the edge ( #11950 )
6 years ago
1410e79e7f
Ensure M109 handles autotemp
6 years ago
e4389f7d23
Standard methods to wait for heating ( #11949 )
6 years ago
bdc9889d3a
Fix a sanity check
6 years ago
321f9140d1
Followup to #11904
6 years ago
23114aeb81
Fix garbled M119 output. Honor NUM_RUNOUT_SENSORS ( #11948 )
6 years ago
1667ed9d1c
Pause should use ECHOLNPGM
6 years ago
93839e2f73
Add option to enable/disable autoretract altogether ( #11904 )
6 years ago
ad21a4f07b
Tweaks to HAL format and order
6 years ago
b682a1961a
Tweak STM32F7 TMC2660 class
6 years ago
a0a3b23e35
Reduce Raptor bootscreen by 144 bytes
6 years ago
95d793456b
Add Formbot Raptor config, fix other Formbot configs ( #11926 )
6 years ago
d016b572e3
[2.0.x] Add pin configuration for Fysetc F6 ( #11932 )
6 years ago
84926b1d5a
HAL general support for DISABLE_JTAG option ( #11211 )
...
Some STM32-based boards may use multiplexed JTAG pins as IO. Up to now the `DISABLE_JTAG` option (defined in pins files) was only supported for AT90-based boards. This commit generalizes the code and adds support for boards based on STM32F1 and STM32F4.
6 years ago
c575c5d5f6
Bring example configs up to date ( #11939 )
6 years ago
6b1a4f30a8
Fix case of T-Rex 3 _Statusscreen.h
6 years ago
ab7bfa86e2
Fix case of T-Rex-3 _Statusscreen.h
6 years ago
241168926d
Update some configs
6 years ago
cb6454118c
Workaround for Pronterface M29
6 years ago
eeab4141db
[2.0.x] Anycubic Trigorilla 14 pins tweak ( #11869 )
6 years ago
cb9dc56630
Add GT2560 v3 support ( #11914 )
6 years ago
f2e630a05e
Stow probe on probing failed ( #11936 )
...
Prevents probe from being left down should probing fail and print job continue
6 years ago
0b602ae101
[2.0.x] Fix Anycubic Kossel with Probe V1, stuck LCD message after stow ( #11929 )
6 years ago
dc11131656
[2.0.x] fix possible race condition ( #11923 )
...
Fix some commits done in #11900
6 years ago
d6b9327c11
Followup for Endstop Noise Threshold
...
Followup to #11912
6 years ago
aa6e8e9325
Tweak some config comments
6 years ago
5490a664f5
Expose: Homing Validation and Endstop Noise Threshold ( #11912 )
6 years ago
cee34f7290
Followup for BABYSTEP_HOTEND_Z_OFFSET ( #11916 )
6 years ago
884ad75cb8
Update config files
6 years ago
18e456d38d
[2.0.x] fix home endstop bug (DON'T MERGE, needs discussion) ( #11900 )
6 years ago
6742026568
Followup for 6 extruders
6 years ago
04bdff4115
Add a blank line
6 years ago
ccbd045f02
Fixed warning about comparing signed to unsigned ( #11909 )
6 years ago
1104054d73
2.0 IDEX Independent z offset and other fixes ( #11862 )
...
* Add Formbot Raptor board
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>
* Add a second Z probe Z offset
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>
* Modify method to utilize live adjustment of hotend z offset
Should probably move config option to babystepping and rename as it may now apply to all multiextruder systems
* Move config item and catchup other code to current method
6 years ago
217e0efd20
General option PAUSE_BEFORE_DEPLOY_STOW ( #11905 )
6 years ago
849dea92a8
Move probe extras below probe types
6 years ago
a2b0260f0f
Update Sublime files
6 years ago
a4cdffdd69
Support for manually deployed fixed probes ( #11899 )
6 years ago
ddcbf80f23
Followup for Z_TRIPLE_ENDSTOPS
6 years ago
c411e7eb0d
[2.0.x] Squelch compiler warnings seen with -Wall ( #11889 )
6 years ago
83105590a0
Better default values for Mesh Inset
6 years ago
4163c1a514
Fix end stop and Z-probe reporting logic
6 years ago
ea9eb2fc8f
Fix servo angles in config-store
6 years ago
d3d6be8210
Add MAX7219 reverse units option ( #11860 )
6 years ago
beab9733f8
Remove extra clauses in config-store
6 years ago
5a74b12b45
Followup to #11769
6 years ago
f38570ac55
Add custom user menu title ( #11769 )
6 years ago
17494099a9
Fix parking_extruder_tool_change
...
Fix #11872
6 years ago
140caf99b8
E0_CS_PIN moved from A13 to A15 on RAMPS-FD v2.2 ( #11865 )
6 years ago
10590c2f80
Fix some fan conditionals
6 years ago
e4ee607fc8
Fix Dual X FRS in M600
...
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>
6 years ago
bae8f82ba8
[2.0] Fix Mixing Extruder mixing factors ( #11861 )
6 years ago
c5e5cc5e9f
Fix some trailing whitespace, macros
6 years ago
54bd124665
2.0.x: Fix normalize_mix() ( #11856 )
...
Mix factors needed to be updated consistent with the recent Stepper/Planner code refactor.
6 years ago
5fbfbde532
Fix example file to pull in correct pins file
6 years ago
378f354939
IDEX Scaled Duplication is still under development
...
Take it out of the menu until it is tested and working.
6 years ago
65045ba54b
tmc_util fix part 2
...
Followup to 115abf9
6 years ago
09a2bee8aa
Support more filament runout sensors in M119 ( #11851 )
6 years ago
115abf9c53
Fix syntax error in front of `tmc_axes`
6 years ago
0780913848
IDEX Improvements ( #11848 )
6 years ago
39732838b4
Tweak indent of Chinese languages
6 years ago
53bd0b55cb
Followup for 6 extruders
6 years ago
1718eff54a
Code changes supporting up to 6 extruders
6 years ago
f5c210d33d
Config changes supporting up to 6 extruders
6 years ago
d948c6e867
RADDS Extension Board V3 support
6 years ago
c437bb08f1
Overhaul of the planner ( #11578 )
...
- Move FWRETRACT to the planner
- Combine leveling, skew, etc. in a single modifier method
- Have kinematic and non-kinematic moves call one planner method
6 years ago
8323a08642
Clean up some whitespace
6 years ago
6286afd456
Add Triple-Z options to example configs
6 years ago
1a6f2b29b8
Add support for Triple-Z steppers/endstops
6 years ago
bc06406d7d
Fix Anycubic Kossel config (probe crash) ( #11832 )
6 years ago
66f83d33e6
Fix some config comments
6 years ago
84ed9b5a63
Send "G33 S P1" for Delta Height Calibration ( #11831 )
6 years ago
215eee4fe5
Use 'friend' to access set_directions
6 years ago
ff51e7322d
Fix for Stepper::set_directions() compilation error ( #11838 )
6 years ago
809b232fa2
Fix stepper directions after M501/M502
...
See https://github.com/MarlinFirmware/Marlin/issues/11103#issuecomment-421387611
Co-Authored-By: tcm0116 <tcm0116@users.noreply.github.com>
6 years ago
f79a5a9dee
Tweak spacing of L6470 options
6 years ago
c37d3ae97d
[2.0.x] Fix NOZZLE_PARK_FEATURE for Anycubic Kossel ( #11812 )
6 years ago
4fb2134f00
Fix non-sensical values for Zonestar themistor table ( #11817 )
...
Values taken from Zonestar firmware for P802QA with a Melzi board. Timestamps from the firmware package are from April 2016.
6 years ago
b220a825a7
Fix raw_filwidth_value error
6 years ago
1933d5d6fb
Fix SD autostart with no LCD
6 years ago
8bce5370c7
Updated slovak translation ( #11807 )
6 years ago
64d629ba2a
[2.0.x] Italian language fix ( #11796 )
6 years ago
8584d3697d
Fix servo count define conflict
...
`MAX_SERVOS` => `NUM_SERVO_PLUGS`
6 years ago
06949ae510
Fix MSG_FILAMENT_CHANGE_HEAT_1 for small LCD
6 years ago
d882717d98
Save some PROGMEM with constexpr ( #11798 )
...
When possible, make `active_extruder` a `constexpr` to save some PROGMEM.
6 years ago
4f883d5971
[2.0.x] Extruder-Distinct Linear Advance K Factors ( #11789 )
6 years ago
fe9f088d60
[2.0.x] Anycubic LinearPlus, Trigorilla 1.4 ( #11730 )
6 years ago
b6aae2b322
Tweak RAMPS_FD_V1 pins
6 years ago
7391e23332
Fix RigidBoard FAN_PIN collision
6 years ago
53b8c3bd66
Add EXTERNAL_CLOSED_LOOP_CONTROLLER to examples
6 years ago
1b6bc19427
Add external closed loop controller support
6 years ago
2ebfe90be9
Add custom preheat temp to filament change ( #11475 )
6 years ago
69d0ed5791
[2.0.x] Fix ambiguous function call (SERIAL_PROTOCOL_F) when using Arduino_Core_STM32 ( #11747 )
6 years ago
d32c4efc77
Fix some trailing whitespace
6 years ago
bc1ba998b2
[2.0.x] Fix undefined symbol 'g29_in_progress' ( #11781 )
6 years ago
bad225dc04
Fix mesh leveling compile errors ( #11768 )
6 years ago
d783400330
Updates to STM32F7 HAL, for completeness ( #11770 )
6 years ago
72af8e0f02
Patch extruder_advance_K edit menu
...
Fix #11776
6 years ago
7e8c073fba
Fix extruder stops extruding with LA ( #11758 )
6 years ago
0c01099f17
hop_amount => current_hop
6 years ago
eafd62308e
Use TMC2208Stepper v0.2.5 ( #11714 )
6 years ago
e25d2ae4a2
[2.0.x] SWITCHING_TOOLHEAD ( #11623 )
6 years ago
f417408df1
[STM32F1] Fix HAL for new PlatformIO ( #11749 )
6 years ago
3d7f2c1fde
Fix directory name to be consistent ( #11745 )
6 years ago
a9c98a0e47
Create _Bootscreen.h
6 years ago
9f85d3a9cb
Create _statusscreen.h
6 years ago
e2e7b1d705
Break out support of the T-Rex 3
6 years ago
67996c2b66
Break out support for the T-Rex 3
6 years ago
9c8d9d282f
Break out support for Formbot T-Rex3 from previous versions
6 years ago
e3aac59637
Create pins_FORMBOT_TREX3.h
6 years ago
f580247581
Create pins_FORMBOT_TREX2.h
6 years ago
073857646b
seperate the T-Rex2 and T-Rex3 support
6 years ago
fe4fc2883b
Add support for Formbot T-Rex3
6 years ago
2a61c9a939
Various fixups to configs, spacing, etc.
6 years ago
b3efbc6e6e
Add MANUAL_E_MOVES_RELATIVE to more configs
6 years ago
679e4602fe
Add MANUAL_E_MOVES_RELATIVE to examples
6 years ago
beb51c2d58
Show manual extrusion moves as relative in LCD
...
- Implements FR#11724
- Old behavior can be restored by commenting out MANUAL_E_MOVES_RELATIVE
6 years ago
d10f29ae2e
Pass segment length in G2-G3
6 years ago
dcfde2317f
Pass segment length in prepare_kinematic_move_to ( #11737 )
6 years ago
d5379ee9d6
Fix search for white space in enqueued commands
6 years ago
8d5bea073b
Assume one Max7219 unit if not specified
6 years ago
9651ceb36b
Correct spelling of #endif
6 years ago
b213a89ef5
Sanity-check NOZZLE_PARK_POINT
6 years ago
86ee74731e
Comment for RADDS + RRDFGSC
6 years ago
ae1271b2ae
RADDS: Update Full Graphic Display Pins ( #11731 )
6 years ago
650d4313c4
Bring some configs up to date
6 years ago
530a13ab6c
[2.0.x] SECURITYFIX missing max temp error when PID is used ( #11717 )
6 years ago
12fded46c2
Correct some FR strings
...
Co-Authored-By: pipersw <pipersw@users.noreply.github.com>
6 years ago
aefc2f7cf9
Add Anet A2 and A2 Plus Configurations ( #11677 )
6 years ago
72fdb6bab3
Fix SWITCHING_NOZZLE zdiff ( #11683 )
6 years ago
8b837dc3ad
No need for last \n in G-code items
6 years ago
d1ceaf5550
[2.0.x] Followup to IDEX changes ( #11707 )
6 years ago
d62f4df0b7
Disable LCD Pins used by new Max7219 hook up if in that mode
6 years ago
fa772c31bf
Provide more options for Max7219 connection on Formbot
6 years ago
8e18e48d49
Merge pull request #11610 from Freeviv/bugfix-2.0.x
...
[2.0.x] Editable servo angles
6 years ago
59e76e5fdf
[2.0.x] Fix planner computation ( #11708 )
...
Fix #11697
6 years ago
7680b64aa6
IDEX clean up ( #11690 )
6 years ago
49e107cea9
Restrict SW serial to AVR ( #11696 )
6 years ago
18f1af2dca
Fix up Teensy tests, servo sanity
6 years ago
74a04aed55
Fix compile error with NO_LCD_MENUS
6 years ago
509e1cf2bd
Add *_DRIVER_TYPE to remaining configs
6 years ago
d55f44edba
Printcounter improvements ( #11689 )
6 years ago
6a3207391f
Remove obsolete HAL_timer_restrain
6 years ago
e3fc9aa35f
Update some config comments
6 years ago
136860e8bb
Sanity-check SERVO pin for servo probes
6 years ago
66de50f5f8
Updated slovak translation ( #11684 )
6 years ago
ada85d5585
Improve HOTEND OFFSET Z display precision to 3 ( #11686 )
6 years ago
607c1e58d9
Improve HOTEND OFFSET Z display precision to 3 ( #11685 )
6 years ago
3e81745e81
Fix issues, make optional
6 years ago
aa80e448e2
Store servo angles in EEPROM
6 years ago
9953213513
Add EDITABLE_SERVO_ANGLES to example configs
6 years ago
0966bdcbc4
Reorganized ultralcd menu (10317) ( #10360 )
...
Replaced "Prepare" and "Control" menus with "Movement", "Temperature", "Configuration" and "Advanced Settings"
6 years ago
e40a3eef04
Support for Anet A2 Plus
6 years ago
32e38fee74
Update Controller Fan for Y2,Z2
6 years ago
59cf217e77
Fix 5 mixing steppers
6 years ago
2a2e8c314e
Suppress emergency parser G-code errors
...
Co-Authored-By: srieche <srieche@users.noreply.github.com>
6 years ago
7ecb8b4af5
[2.0.x] Teensy 3.1 and 3.2 support ( #11460 )
6 years ago
409a0632af
[2.0.x] Add Morpheus Board support ( #11651 )
6 years ago
0f14977b5d
LIGHTWEIGHT_UI: Allow feedrate % to exceed 255% ( #11656 )
...
- Changed type of integer used for feedrate percentage from uint8_t to uint16_t.
6 years ago
6dc9553aa5
Fix SWITCHING_NOZZLE compile error ( #11657 )
6 years ago
a15e570d3b
Fix SD progress with Lite Status Screen
...
Co-Authored-By: Lê Hoàng <icy.lord.love.angel@gmail.com>
6 years ago
66966dbd69
Tweak comments for newer multiplexer
6 years ago
933d833ec8
Tweak some Anet A6 comments
6 years ago
d1c9517903
Followup to hotend_offset[Z] patch
6 years ago
e2b8fc4f17
Reduce some debug strings
6 years ago
b71c2b8651
[2.0.x] Update LPC176x tests, fix clean script ( #11617 )
6 years ago
a317bb4991
Remove stray tab
6 years ago
acf5ae3083
!ENABLED => DISABLED
6 years ago
ba1919c1eb
HAL tweaks to LPC1768 main
6 years ago
0987ed2a18
Use American English
6 years ago
6483285bc5
HOTEND_OFFSET_Z always available ( #11603 )
6 years ago
f8c52c9c29
Azteeg X5 Mini WiFi support ( #11601 )
6 years ago
3671c63cde
Einsy Full Graphic LCD Fix ( #11604 )
...
Fixed issue with LCD timings for Einsy RAMBo board.
6 years ago
593d5375ea
Fix G28 resetting DUAL_NOZZLE_DUPLICATION_MODE ( #11605 )
...
There's no reason for G28 to reset DUAL_NOZZLE_DUPLICATION_MODE, because it only affects the E stepper, unlike DUAL_X_CARRIAGE which affects the X steppers as well.
6 years ago
f0dbe61692
Tweaks to motion.h reachable tests
6 years ago
2d3317a35b
Prettify Dual X Carriage description
6 years ago
cd9868f442
Make position_is_reachable() smarter about IDEX machines`
...
On many IDEX machines the allowed travel of the X1 carraige and X2 carraige does not perfectly overlap.
This helps the issue. But more work needs to be done at the higher level. (For example the X1_MAX_POS should probably be factored into G26's mesh validation pattern.)
6 years ago
97f6396b25
Fix RE_ARM LCD pins to avoid #undef
6 years ago
0e25f66c09
Fix Ultimaker servo pin
...
As pointed out at https://github.com/MarlinFirmware/Marlin/issues/7981#issuecomment-407116642
6 years ago
ad12b9b46b
Fix indentation, whitespace, spelling, formbot pins...
6 years ago
b5537dde7f
need to add E2END to pins_RAMPS_FD_V2.h ( #11564 )
6 years ago
8f0bbdcc9b
Fix up Max7219 orientations ( #11596 )
6 years ago
a77f8c6dd5
Implement servo support for STM32F1 ( #11580 )
...
Implement servo support for STM32F1. Original code was incomplete and depended on Servo library from stm32duino which conflicts with `module/servo.h`.
6 years ago
0456caf0ad
Consolidate shared HALs and isolate HAL compile ( #11552 )
6 years ago
dfe18ac633
Fix compilation error for STM32F1 with U8GLIB_SSD1306 or U8GLIB_SH1106 enabled ( #11583 )
...
The `binary.h` file required by `lcd/dogm/dogm_bitmaps.h` is not present in stm32duino environment. Binary macros are defined in `bit_constants.h` in stm32duino framework.
6 years ago
b0a8ce59bd
Update Boards.h to include Formbot support
6 years ago
62ce937540
Update pins.h to include the Formbot board
6 years ago
a82be36d5d
Create pins_FORMBOT.h
6 years ago
00d24a8219
Don't call __delay_4cycles for 0 cycle delay - takes a really long time. ( #11586 )
6 years ago
56f1e17a25
[2.0.x] Max7219 cleanup, simplify, and extend ( #11575 )
6 years ago
0b2d686160
Fix "SD init fail" problem for STM32F1 ( #11579 )
...
Fix "SD init fail" problem for STM32F1 caused by incorrect SS pin state and incorrect SPI mode. Issue #11225
6 years ago
db30650731
Fix UBL/Homing ( #11566 )
6 years ago
aae4c67e5d
Max7219 Clean Up ( #11563 )
...
Some of the Rotations did not do the right thing with setting and clearing pixels.
I think it is correct now. But if not... It is much closer to being correct.
6 years ago
9de730b2bf
Update tool_change.cpp ( #11559 )
6 years ago
c2553f9888
2.0.x - Idex match119 ( #11556 )
...
* Update ubl_G29.cpp
* Update ultralcd.cpp
6 years ago
e9de321ac0
declare void Max7219_register_setup();
6 years ago
952a1bc9d5
Merge pull request #11551 from thinkyhead/bf2_trinamic_fixes
...
[2.0.x] Fix TMC2208 SW serial communication
6 years ago
67613bf5bd
Update Czech translations ( #11510 )
6 years ago
bd6d032628
Update default driver configuration
...
Co-Authored-By: teemuatlut <teemu.mantykallio@live.fi>
6 years ago
1561e61df7
New TMC2208 constructor
...
Co-Authored-By: teemuatlut <teemu.mantykallio@live.fi>
6 years ago
b37bfeffeb
[2.0.x] Use the new const functions of the persistentStore api ( #11544 )
6 years ago
5573ef62c6
[2.0.x] PersistentStore update followup ( #11549 )
6 years ago
846bd24eb9
MALYAN_LCD is ok without SD
6 years ago
834ea7fcea
Remove 'const' from PersistentStore::capacity
6 years ago
c64199941e
Compile only selected PIO environment ( #11519 )
6 years ago
5be2559eda
Use flash memory to emulate EEPROM ( #11500 )
...
Use a sector of the LPC flash memory to emulate EEPROM storage, removing the need to have an SD card to store system parameters.
6 years ago
6964e1a95a
Clean up trailing whitespace
6 years ago
865ee5985f
Followup persistent store with heading, const
6 years ago
a4b0148365
Easier to find 'static inline'
6 years ago
cc0a60453f
Merge pull request #11526 from hasenbanck/eeprom-cleanup
...
[2.0.x] Change direct eeprom access to HAL::PersistentStore
6 years ago
65c5227c29
Change M7219 I to setup Max7219 registers, but not do initialization pattern
6 years ago
577aeb4aa9
All EEPROM access uses persistentStore
6 years ago
6a8b906318
Followup for persistent_store_api.h
6 years ago
66d2b48b59
Update PersistentStore api ( #11538 )
...
- Clean up the API to use a `static` class instance to adhere to Marlin convention
- Add `const` position data access for read/write
- Add Storage capacity to the interface
6 years ago
60f1376798
Make M7219 I more robust and nice to look at
...
Make M2719 initialize the Max7219 registers and then run the initialization pattern (if one is specified).
6 years ago
fd15b1495a
add I parameter to M42 to allow access to sensitive pins
6 years ago
11b411a872
Improve AXIS_DRIVER_TYPE macros
6 years ago
f1347f783d
Optimize thermistor table 71
...
agData in Table 71 is extremely oversampled (see Issue #11220 ). I have removed the data points that perform *worse* than linearly interpolating the remaining points, and fixed up two points that were simply rounded incorrectly.
Co-Authored-By: Aaron Griffith <aargri@gmail.com>
6 years ago
0bda22367b
Allow Einsy RAMBo FAN1_PIN override
6 years ago
1b921b246b
Fix pca9632_set_led_color
...
…when used with an I2C screen.
Co-Authored-By: soimy <soimy@163.com>
6 years ago
aa9d329560
Reduce max accel in Creality configs
6 years ago
c93538e9f3
UBL/planner patch tweaks
6 years ago
0af22549a6
Allow G33 to compile with no LCD
6 years ago
fc55f1da01
Account for UBL correction when setting the planner position ( #11486 )
6 years ago
b328fb4dc9
Treat TMC2660 like non-TMC ( #11508 )
6 years ago
72b086b90d
Add A5984 to example configurations
6 years ago
a1a5367380
Smoothieboard V1.0/1.1 and A5984 support
6 years ago
f891416e70
No raise on G28 after power-loss
6 years ago
e4ecade8d4
Fix AUTO_POWER_CONTROL compile error
...
Counterpart to #11467
Co-Authored-By: lsellens <lsellens@users.noreply.github.com>
6 years ago
eee1b7c50c
[2.0.x] Fix compile error ( #11465 )
...
Address #11463
6 years ago
e85feb2545
[2.0.x] Better timing handling ( #11461 )
6 years ago
79835590e3
Easier to disable homing validation ( #11458 )
6 years ago
131d216afa
Fix drivers.h dependency, defer macro evaluation ( #11450 )
7 years ago
9c62c47579
[2.0.x] Fix Dual X Carriage tool change crash ( #11447 )
7 years ago
9bae413901
Add Bigtreetech/BIQU KFB 2.0 board ( #11446 )
7 years ago
f2224755ad
Fix jumping progress bar. ( #11439 )
...
- When LCD_SET_PROGRESS_MANUALLY was disabled and an SD print was not active (i.e. the printer was idle), progress_bar_percent would read uninitialized memory from stack and cause progress bar to jump wildly.
- Also updated conditions in `#ifdef` to match `ultralcd.cpp`
7 years ago
aae02827c0
Cosmetic pins changes
7 years ago
64c493ad82
MKS_12864_OLED code cleanup
7 years ago
b826bf4194
Fix initial safe_speed in jerk code ( #11417 )
7 years ago
2cc950d67e
[2.0.x] MKS SBASE Trinamic examples/support ( #11402 )
7 years ago
16432376ab
Revert "[2.0.x]Idex and bl touch fixes" ( #11407 )
...
* Revert "[2.0.x] bltouch home refinements (#11397 )"
This reverts commit 74900f7a70#11395 )"
This reverts commit 6dafb90c01
7 years ago
74900f7a70
[2.0.x] bltouch home refinements ( #11397 )
...
Just create a better functions call logic flow
7 years ago
6dafb90c01
[2.0.x]Idex and bl touch fixes ( #11395 )
...
* Fix BLTouch homing
Deploy at start, dont call generic stow function at finish or raise goes too high before setting 0
* Update tool_change.cpp
* Update motion.cpp
* Update motion.cpp
* Update motion.cpp
* Update motion.cpp
* Change brackets to be more in align of Marlin coding standards
7 years ago
5ce5ff8e9b
[2.0.x] fix bltouch homing ( #11379 )
...
Partially revert. Seems to solve the issue, but one report says G29 still fails.
7 years ago
15d68cb496
Pre-override of ST7920 delays before HAL.h
7 years ago
8a24ff94d1
AT90USB1286 PIO cleanup and optimization ( #11230 )
...
-normalize `env` and `board` to lowercase naming convention.
-make board `name` follow descriptive convention.
-implement `-fsingle-precision-constant` compile optimization per https://github.com/MarlinFirmware/Marlin/pull/11178#issuecomment-401673901
-fix typo in 5DPRINT entry.
7 years ago
094e6d81a5
Add Einstart-S support ( #11219 )
...
Indeed the HAL does not need to be mucked around with to expose ATmega2560 pins not available as numbers on the MEGA board, I'll need to update the wiki with that tidbit and a reference to the pin-mapping comment in `fastio_1280.h`.
7 years ago
244b9a8257
Better fastio 1280/2560 pin list
...
Co-Authored-By: bleughb <36889022+bleughb@users.noreply.github.com>
7 years ago
955a7f0ae9
Improve driver.h macros ( #11371 )
7 years ago
aadcf08913
[2.0.x] add Calibrate Z (M915) to Prepare Menu ( #11331 )
7 years ago
4237c3d9f8
[2.0.x] different bltouch init ( #11135 )
7 years ago
624986d423
Ensure ADC conversion is complete before reading ( #11336 )
...
The current Marlin implementation relies on a timer interrupt to start the ADC conversion and read it. However in some circumstances the interrupt can be delayed resulting in insufficient time being available for the ADC conversion. This results in a bad reading and false temperature fluctuations. These changes make sure that the conversion is complete (by checking the ADC hardware via the HAL) before reading a value.
See: https://github.com/MarlinFirmware/Marlin/issues/11323
7 years ago
e2aa635e70
Fix Anet A6 thermistors
...
Co-Authored-By: vitekn <vitekn@users.noreply.github.com>
7 years ago
67b205fd45
Add support for board RuRAMPS4D v1.3 ( #11363 )
7 years ago
d1c6687ecd
Update MKS sBase pins ( #11357 )
7 years ago
048dbf6eca
Merge pull request #11275 from thinkyhead/bf2_pwm_adjustments
...
[2.0.x] Tweak some SoftPWM code
7 years ago
e05e95cf97
Clean trailing whitespace
7 years ago
22ebbc091f
Tweak some SoftPWM code
7 years ago
32de09f5c5
Specify some extra CR-10S pins
7 years ago
9c2bfa2ab3
Remove extra parameter to enqueue. ( #11364 )
7 years ago
bd3ec66a78
[2.0.x] typo fix ( #11365 )
...
Typo fix
7 years ago
fbcdf5eaeb
Simplify stepper driver per-axis selection
7 years ago
e5c0b490c8
Add *_DRIVER_TYPE to example configs
...
Co-Authored-By: teemuatlut <teemu.mantykallio@live.fi>
7 years ago
fbdbe53290
Fix get_period_inverse(0) so it doesn't crash ( #11334 )
7 years ago
14e2b11195
Fix spelling in configs
7 years ago
4685c7d59f
Followup to M91x I patch
7 years ago
62fa028155
Handle dual gantry machines better
7 years ago
09485f63e9
add missing ')'
7 years ago
a35abce1ac
Fix missing ')'
7 years ago
76d4cfb064
Tweak some Max7219 code
7 years ago
4195757585
Merge pull request #11309 from thinkyhead/bf2_manual_probe_start_z
...
[2.0.x] Manual Z Start Height
7 years ago
03b01e2500
Folger Tech i3-2020 now defaults to 2 Max7219 units
7 years ago
db85ca93c4
Change Max7219_idle_task() to use a column instead of row if Y-Axis as 16 LED's
7 years ago
9660996cc3
Add Multi Unit Support for Max7219 to bugfix_2.0.0 ( #11285 )
...
* Add Multi Unit Support for Max7219 to bugfix_2.0.0
* Apply multi-MAX7219 to example configs
* Tweak some spacing, macros
7 years ago
39c8aed8ba
Add MANUAL_PROBE_START_Z to example configs
7 years ago
2106fa26b1
Add MANUAL_PROBE_START_Z for manual probing
7 years ago
17ed0f815c
Fix tool_change call in UBL G29
...
Fix #11279 , #11252
7 years ago
6d2aff03bd
Merge pull request #11306 from thinkyhead/bf2_power_loss_pin
...
[2.0.x] Add support for power loss detect pin
7 years ago
63a146d424
planner.synchronize at start of tool_change
...
See https://github.com/MarlinFirmware/Marlin/issues/10949#issuecomment-398540498
7 years ago
665ac1e4d0
Add POWER_LOSS_PIN support
7 years ago
2243f72523
Add POWER_LOSS_PIN to example configs
7 years ago
47d5fcbbcc
[2.0.x] Change MKS SBASE default serial port to avoid confusion ( #11301 )
7 years ago
c83109c0ae
Merge pull request #11238 from xC0000005/MalyanLCDUpdate
...
[2.0.x] Malyan LCD Feedrate + Better Temp Handling
7 years ago
64f007580b
Fix some header comments
7 years ago
aed1d17a2d
Initialize default units ( #11295 )
...
When `INCH_MODE_SUPPORT` is enabled no default unit is set. This fixes it.
7 years ago
8c40f0c6c7
Reduce TQ message code size
7 years ago
b04e0c0cbb
Malyan LCD feedrate, better temp handling.
7 years ago
065e9c3d66
Add card.longest_filename method
7 years ago
71df1f7f57
Don't display M421 information for UBL at startup
...
It takes too long to display the mesh data for large mesh's at startup. We should consider ways to speed this up.
Perhaps it makes sense to display an entire row of the mesh instead of just one mesh point?
7 years ago
be7d1dfb3c
Merge pull request #11267 from teemuatlut/bf2_lpc_spi
...
[2.0.x] LPC1768: Expand hardware SPI class
7 years ago
8f686aa449
[2.0.x] Fix change filament crash ( #11269 )
...
Prevent crash, on filament change, when printer is not homed
7 years ago
f38c81cdde
LPC176x: Expand HW SPI class
7 years ago
3b5dec4b13
Add new LPC include folder
7 years ago
e486326910
Vellemann K8400 Y bed size is 180
...
Co-Authored-By: kaimimue <kaimimue@users.noreply.github.com>
7 years ago
e5ea9d200f
[2.0.x] fix kill printer ( #11260 )
...
This will fix kill message on dual printer with 0 alignment offset
7 years ago
8c57cadbe7
Include stdlib in fontutils ( #11251 )
...
When `REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER` is defined and Re-ARM build is attempted, `u8g_fontutf8.cpp` includes `fontutils.h` which uses `abs()`.
However, `abs()` is defined in `stdlib.h` which is not included in `fontutils.h`, so compile fails with an error.
Include `stdlib.h` in `fontutils.h` so that `abs()` is defined before `u8g_fontutf8.cpp` needs to use it, resolving the compile error.
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
7 years ago
bf7d0ba859
Assert that XY probe offsets are integers
7 years ago
12854f1909
Add Z_CLEARANCE_MULTI_PROBE to example configs
...
Co-Authored-By: nightgryphon <ngryph@gmail.com>
7 years ago
25e2ca8896
Add Z_CLEARANCE_MULTI_PROBE
...
Co-Authored-By: nightgryphon <ngryph@gmail.com>
7 years ago
fd8a76493b
Unify M91x parameter I meaning, simplify reports ( #11249 )
7 years ago
566d05006d
report_state > event_handler
...
Make the endstop report method track endstop changes on its own.
7 years ago
6b521b6df2
Loosen thermistor table size limit
...
Co-Authored-By: Aaron Griffith <aargri@gmail.com>
7 years ago
20761b88e0
Merge pull request #11212 from AlexanderAmelkin/2.0-HD44780-remove-unused-include
...
[2.0.x][HD44780] Remove unused include
7 years ago
603e136e87
Resolve issue where user can't edit UBL's mesh
7 years ago
ed720194d2
[2.0.x][HD44780] Remove unused include
...
The <binary.h> header is not available in STM32 toolchain
and is not used anywhere in ultralcd_common_HD44780.h.
If it is used anywhere in HD44780 support for other platforms,
it must be included in the corresponding .cpp file directly
and put under appropriate conditional compilation directives
for the platform requiring it.
As I was unable to find such code, I consider the file unused
and hence remove the inclusion.
7 years ago
d05e832f29
Add STM32F1 support for SD-based EEPROM
7 years ago
63f4c9bdb9
Followup to float maths patch
7 years ago
2992112da0
Optimize delta kinematics
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
1367df2875
Replace double with float, optimize calculation
7 years ago
d960d448fa
Optimize calculations with LROUND
7 years ago
68e6650df7
Remove Quake Fast Inverse SQRT (it isn't faster)
7 years ago
e7e896e7d7
More tweaks to fastio_Due.h
7 years ago
55f4744e54
[LPC176x] Endstop Interrupts Feature ( #11202 )
...
Enable the endstop interrupts feature for LPC176x boards. Although Smoothieboard chose to use non-interrupt capable pins for their endstops, and this has been copied by clones, so they can't use it.
7 years ago
5abf5bc8a7
[LPC176x] Fix Interrupt forward declarations ( #11200 )
7 years ago
cbea385ed7
[2.0.x] Fix LCD_LANGUAGE options list formatting in config ( #11198 )
...
* Fix LCD_LANGUAGE options list formatting in config
* Remove 'cn' language option from list
7 years ago
6837252fba
Merge pull request #11196 from thinkyhead/bf2_fix_m914_sgt
...
[2.0.x] No M914 or SGT with non-sensorless axes
7 years ago
5379c115c8
Fix Trigorilla include typo
7 years ago
9c058091e9
No M914 or SGT set for non-sensorless axes
7 years ago
c7ec6c68e7
Patch SCARA config to match 1.1.x
7 years ago
480a3d3d0c
Apply sensorless homing requirements only for specified axes
7 years ago
47ee149dfd
Merge pull request #11195 from thinkyhead/bf2_tronxy_x3a
...
[2.0.x] Tronxy X3A configurations and thermistor
7 years ago
8c0ec81a19
Followup to #11187
7 years ago
48c1f32b3e
Add configurations for Tronxy X3A
7 years ago
568cfe7caa
Add thermistor 501 (100K Zonestar)
7 years ago
1a0f4dedad
Fix and improve POWER_LOSS_RECOVERY ( #11187 )
7 years ago
e0ab8acf19
Add "Marlin Dev Mode" option
7 years ago
4b2af6ab48
Minor patches to POWER_LOSS_RECOVERY
7 years ago
1ea222e6fc
Turn off DISABLE_INACTIVE_EXTRUDER with SWITCHING_NOZZLE
...
Fix #11183
7 years ago
8299ac121d
[2.0.x] Slovak translation update ( #11175 )
7 years ago
3de0c85d41
Fix RRW graphical LCD constructor macro ( #11171 )
7 years ago
cedc158106
[2.0.x] Board specific init macro ( #11170 )
7 years ago
5616581eb1
[LPC176x] Update fastio _GET_INPUT, _GET_OUTPUT macros ( #11168 )
7 years ago
8a8eae8d97
Implement more fastio_Due macros ( #11165 )
7 years ago
c51e27d11d
Do a hard kill for failed homing moves ( #11161 )
7 years ago
90ba77ea0f
Lose the old HOMEAXIS macro
7 years ago
2421f3a47d
Detect endstop hits in any direction
7 years ago
f9a090b2cf
Fix Trigorilla 1.4 pins
...
See #11097
7 years ago
8eaac0dab3
Add delta feedrate scaling ( #11153 )
7 years ago
444725ae9a
Non-conflicting CS pins for MKS Gen L
7 years ago
8c9f90153e
Enable Malyan LCD Support for M200 printers. ( #11051 )
7 years ago
fc10101b06
Tweaks to fastio_Due.h
7 years ago
05518d6add
Add newline to end of file
7 years ago
d4fde91222
Fix serial.h including itself
7 years ago
a431013eb7
Fix G33 compile warning
7 years ago
bd7f5848f1
Remove JUNCTION_DEVIATION_INCLUDE_E option ( #11147 )
7 years ago
fbf1c9b496
Fix and tweak POWER_LOSS_RECOVERY ( #11151 )
7 years ago
0fff79c24b
Fixes G29_with_retry behavior ( #11045 )
...
* Fix G29 (ABL) retry behavior
7 years ago
3349eb0020
Fix SKEW_CORRECTION compile error
7 years ago
a264030526
Fix "G29" G29_MAX_RETRIES handling
7 years ago
42f9921482
Ignore Z min endstop with separate Z-probe
...
To allow for the case where a Z endstop (e.g., hall effect) is higher than the probe trigger point, don't check the Z min endstop during probe moves. See #11134
7 years ago
1b8973eb1c
Fix up microsteps conditionals
7 years ago
aa4cd2e861
Eliminate stepper.* signed/unsigned warnings
7 years ago
edb21f349a
Fix stepper/planner block handling, race conditions ( #11098 )
...
- Allow planner to alter the deceleration phase of the currently executing block.
- Remove BUSY flag, as it is NON ATOMIC to set bits in the Stepper ISR and Planner at the same time.
7 years ago
4d3a9930c5
Match ASM comment spacing to 1.1.x
7 years ago
053438a3aa
Poll all endstops, even when stationary ( #11123 )
7 years ago
3b3029c4bf
Make max_e_jerk an array to reduce CPU usage ( #11118 )
7 years ago
d13f76b7da
Patch some loop macros
7 years ago
229b26b02c
Clear LED matrix without startup test
7 years ago
ffdbc1f42c
STM32F1: Fix SD card persistent store API ( #11090 )
7 years ago
8d8f257384
[2.0.x] Fix advanced pause init values ( #11095 )
...
Fixed for cycle used to initialize default values
7 years ago
5b49fccf80
Add stepper driver DIR delay configuration option
...
...and recommended pulse width configuration for A4988
7 years ago
d86f25ab63
Fix Serial ISR priority for LPC1768
...
Co-Authored-By: p3p <p3p@p3psoft.co.uk>
7 years ago
fb4e0b105b
Fix endstops compilation error
7 years ago
48a15d1c7e
[2.0.x] Fix stepper/planner race condition and Stepper pulse timer ( #11081 )
...
* Planner: Removal of some race conditions between Stepper ISR and Planner, some of them pointed out by @AnHardt, some of my own findings
* Fixing timing on stepper pulses adding a compensation for the non-null time required to set ports.
7 years ago
7e802145cc
[2.0.x] Add CR-10 stock display support for Re-Arm (EXP3) ( #11068 )
7 years ago
50b6204079
Fix LIN_ADVANCE max_e_jerk_factor
...
According to https://github.com/MarlinFirmware/Marlin/issues/9917#issuecomment-399204568
7 years ago
99591dc20c
Filter endstops state at all times ( #11066 )
7 years ago
a5c11bf578
Merge pull request #11075 from thinkyhead/bf2_value_editing
...
[2.0.x] Fix value editing (with callback)
7 years ago
1d7dd0edfd
Add the move_z_after_probing() functionality to UBL's G29 J
7 years ago
383129728a
Edit Z fade as whole numbers
7 years ago
1239e8eda2
Fix value editing with callback
7 years ago
7a84b03796
Use MIN/MAX in post-conditionals
7 years ago
a2a30ff0ac
Use Tool 0 for Dual X Axis G29
...
See https://github.com/MarlinFirmware/Marlin/issues/5597#issuecomment-397683325
7 years ago
e366d55bc2
Don't reset stepper timeout for all g-codes
7 years ago
7406f04029
Use MAX (not max) in stepper.h
7 years ago
7c54c4ed27
Tiny improvement to M7219
...
The registers within the Max7219 can get corrupted a number of ways. This allows the Max7219 to be reset and fully initialized.
And... it also allows the user to see the initialization pattern.
7 years ago
a65d15c905
[2.0.x] Fix Italian msg len ( #11058 )
...
Fix message to long for 12864 display
7 years ago
d4795e5b8e
[2.0.x] Tweaks and additions for MAX7219 ( #11034 )
7 years ago
e23677a7b2
Update some G-code comments
7 years ago
0312c42f9d
[2.0.x] LPC176x Serial cleanup ( #11032 )
7 years ago
c1269c2ec1
Tweak AVR critical section defines
7 years ago
da94e0bd27
Unsigned eeprom mesh addresses
7 years ago
f88adcbfd5
[2.0.x][LPC176x] Fix binary linking broken by pio update ( #11026 )
7 years ago
e2aeda61ed
HAL for Espressif ESP32 Wifi
7 years ago
091f742432
Add WIFISUPPORT to example configs
7 years ago
19d4c7c1cd
Tweak HAL header comments
7 years ago
cce0523a95
[2.0.x] reset bltouch on home ( #11018 )
...
Added reset bltouch instead. This ensure properly stow even when in error.
7 years ago
4c8d6df13c
Extra insurance against endstop false positives ( #11013 )
7 years ago
81edbfa665
Merge pull request #11004 from ejtagle/always_honor_maximum_step_rate
...
[2.0.x] Fix stepper pulse minimum period and timing calculations
7 years ago
f3fed52348
Fix coolstep_min_speed / sensorless homing
...
Fix #8890
7 years ago
a215725df6
Fix stepper pulse timing
...
Always honor minimum period on stepper pulse generation, and fix timing calculations
Signed-off-by: etagle <ejtagle@hotmail.com>
7 years ago
0d79128c8d
Localize stepper-specific defines
7 years ago
a9861a780e
Tweak HAL heading
7 years ago
cf53e502a2
No need to set input after attachInterrupt
7 years ago
e0276d2f32
Official STMicroelectronics Arduino Core STM32F4 HAL compatibility ( #11006 )
7 years ago
4dbec774b5
HAL_*_TIMER_RATE => *_TIMER_RATE
7 years ago
12689f2470
Merge pull request #11001 from thinkyhead/bf2_junction_deviation_fix
...
[2.0.x] Updates for junction_deviation_mm
7 years ago
9b945c13a1
Fix STM32F1 ISR_ENABLED
7 years ago
9d04f47d98
Improvements for junction_deviation_mm
...
- Drop `max_jerk` with `JUNCTION_DEVIATION`
- Add `max_e_jerk_factor` for use by `LIN_ADVANCE`
- Recalculate `max_e_jerk_factor` when `junction_deviation_mm` changes
- Fix LCD editing of `junction_deviation_mm`
7 years ago
f2c3b0d476
Use bit flags for homed/known
7 years ago
4832be52d7
Followup to G29 O
7 years ago
86170e6a66
[2.0.x] Add O (optional) flag to G28/G29 ( #10913 )
7 years ago
2ddba201c0
STM32F1 HAL Fixes ( #10999 )
...
- Enable / disable interrupts with `__iSeiRetVal` / `__iCliRetVal`
- Add STM32F1 to Travis CI tests
7 years ago
43bdd0bfe4
Fix indent in stepper.h
7 years ago
2ba198a624
Tweak M122 report spacing
7 years ago
5590c8ffd0
Fix MarlinSerial (AVR) ( #10991 )
...
An undocumented hw bug makes the UART lose chars when RX ISR is disabled, even for a very small amount of time. This happens when RX_BUFFER > 256, and the result is corrupted received commands. Solved by implementing pseudo-atomic operations on 16bit indices.
7 years ago
3fd1f32b73
Fix ADC key and chamber temp
7 years ago
117fd007a9
Followup to pin error change
7 years ago
ae07a3e4aa
Multiplier edit large ranges
7 years ago
20a5db03bb
Junction Deviation limit (0.01 to 0.3)
7 years ago
a2f521d34b
Add Junction Deviation mm runtime setting ( #10990 )
7 years ago
590ce1c33e
Fix serial debug ouput
7 years ago
968a5d2e63
Protected pin err for M226
7 years ago
4b90cd8ead
Merge pull request #10922 from ejtagle/bugfix-2.0.x
...
[2.0.x] Adaptive multiaxis step smoothing, and tons of fixes
7 years ago
f1cdfe3dfd
[2.0.x] stow bltouch before start homing ( #10987 )
7 years ago
6f14bcaa3e
Add MAXIMUM_STEPPER_RATE, enforce in multi-stepping
...
The timing value should be properly set for ALL boards. The compiler will check and set maximum step rate calculations based on those values.
7 years ago
39a7e7720d
Adaptive multiaxis step smoothing
...
- Stepper bugs fixed
- Support MIXING_EXTRUDER with Linear Advance
- Miscellaneous cleanup
7 years ago
99af086cea
Add hidden Serial overflow debug options
7 years ago
d90e8fcad9
Fix XON/XOFF implementation
...
Pointed out by @GMagician
7 years ago
bbf80440bf
Add sanity-check for MOTHERBOARD
7 years ago
b64cc9329e
[2.0.x] Fix dual enstop home ( #10980 )
7 years ago
8a376e6beb
Update MINIMUM_STEPPER_PULSE description
7 years ago
3701869e6c
Add HAL_timer_start for AVR, use stepper timer to time pulses
7 years ago
e970e429b6
[2.0.x] Fix null check in lsDive ( #10978 )
7 years ago
d82704354f
Increase the planner first block HOLD delay to 100mS
7 years ago
779d4a17a0
Highlight 64128N and common ST7565 difference
...
Followup to #10920 , addressing #10962
7 years ago
b9418439b9
Prevent MB false-positive on bad board name
7 years ago
88314b8910
CREALITY_ENDER is long gone
...
As noted in #10965
7 years ago
334341c632
Hephestos config updates ( #10960 )
7 years ago
f74278b8b1
Add -4 thermocouple to list in configs
7 years ago
7ba5afff01
Allow FAN_PIN override, pins cleanup ( #10956 )
7 years ago
55aedf036b
Fix M503 ABL mesh report. (Zero-based IJ indices)
7 years ago
e7623b5788
Restore Z_PROBE_PIN to pinsDebug_list.h
7 years ago
a426986df8
Ensure pins set to INPUT after attachInterrupt ( #10928 )
7 years ago
d8b983f624
More concise M503 output for M906, M913, M914 ( #10947 )
7 years ago
eb1026d438
[2.0.x] Fix compile warning ( #10931 )
7 years ago
c2bdbdffaa
Prevent a buffer overflow in diveToFile
...
Co-Authored-By: akunt
7 years ago
c9d1a620d4
[2.0.x] fix indentations ( #10934 )
7 years ago
d550da084f
Fix Max7219 control pins for use with 32-bit platforms
7 years ago
c16e41e9e6
STM32F4 pins cleanup
7 years ago
c685c7b7dd
STM32F4: All pins can do PWM
7 years ago
2fd9ba56da
LED menu item bool (like Case Lights)
7 years ago
ad8d3150aa
Cleanup for dual endstops homing
7 years ago
61181b7f24
Add macros for ST7565 commands
7 years ago
d3c02410a8
[2.0.x] Small assorted collection of fixes and improvements ( #10911 )
...
* Misc fixes and improvements
- Get rid of most critical sections on the Serial port drivers for AVR and DUE. Proper usage of FIFOs should allow interrupts to stay enabled without harm to queuing and dequeuing.
Also, with 8-bit indices (for AVR) and up to 32-bit indices (for ARM), there is no need to protect reads and writes to those indices.
- Simplify the XON/XOFF logic quite a bit. Much cleaner now (both for AVR and ARM)
- Prevent a race condition (edge case) that could happen when estimating the proper value for the stepper timer (by reading it) and writing the calculated value for the time to the next ISR by disabling interrupts in those critical and small sections of the code - The problem could lead to lost steps.
- Fix dual endstops not properly homing bug (maybe).
* Set position immediately when possible
7 years ago
2deff0d9b9
Fix/Improve junction deviation
...
- Respect axis max acceleration limits instead of forcing a fixed acceleration value.
- The `junction_unit_vec` ensures proper handling of entry and exit speeds even when the axes involved have different limits.
7 years ago
6885ca606c
Drop JUNCTION_ACCELERATION from example configs
7 years ago
d87257f63c
[2.0.x][LPC176x] Fix PIO build flags ( #10909 )
...
Don't build and link with different flags, the binary may not work.
7 years ago
ae322e0c54
[2.0.x] Add GTM32 Pro VB support ( #10898 )
7 years ago
d259070980
Clean up trailing spaces from vim, etc.
7 years ago
21d812d502
Fix the Z un-hop on G11
...
Co-Authored-By: zarthcode <anthony.clay@zarthcode.com>
7 years ago
d3c473002a
For SCARA probe Y offset is proximal/distal
7 years ago
b90f54b0fc
Improve probe logging
7 years ago
3f2a062a57
Fix M914 value range (-64...+63)
...
Fix #10896
7 years ago
b6cd8d9cc6
Set deltas to park on the left
7 years ago
9713538427
HOTENDS for Switching Nozzle with Switching Extruder
7 years ago
c68b7b3913
Update Fan 2 and E0 Auto Fan pins for Trigorilla
7 years ago
cbcb284f4a
Allow libServo::attach to work on Teensy 3.5/3.6
7 years ago
f89f7c4a82
[2.0.x][LPC176x][Build] Force single precision constants, disable freestanding ( #10892 )
7 years ago
4299e5dc8b
Modify E-stepping macros for use in LINEAR_ADVANCE ( #10885 )
7 years ago
8f14ef855d
More concise commentary in planner.cpp
7 years ago
6919e87656
Minor cleanup of multi-stepping logic
7 years ago
16da5c62d0
Teensy 3.x fastio pullup ( #10890 )
7 years ago
853a9056ac
Long thermistor tables need special consideration
7 years ago
a4f9c3373f
Tweak thermistor spacing
7 years ago
9b9b62b218
delay(SERVO_DELAY) => safe_delay(servo_delay[servo_index])
7 years ago
1ce97f1f6d
Faster (bisect) search in thermistor tables ( #10883 )
7 years ago
0ca9db7051
Correct HOTENDS for SWITCHING_EXTRUDER
7 years ago
945139e328
Clean up some formatting
7 years ago
9c235ef821
[HAL]Add support for ST7920 - Teensy 3.x ( #10872 )
7 years ago
7b9f0302d4
Fix Bresenham rounding errors, add link to article ( #10871 )
7 years ago
2566342979
Adjust some commentary
7 years ago
1b200f3312
Sanity check SWITCHING_EXTRUDER with SINGLENOZZLE
7 years ago
6775a16c97
Fix switching extruder stepping with LA
7 years ago
2e139fe50f
Tweak configuration spacing
7 years ago
931ab4ec40
Rename Junction Deviation options
7 years ago
aaaf09bda2
BEZIER_JERK_CONTROL => S_CURVE_ACCELERATION
7 years ago
cf7d5a642a
Fix manual moves for switching tools ( #10868 )
7 years ago
1da2c4f1c1
Text LCD display routine fix. Coauthored with @MagoKimbra ( #10864 )
7 years ago
1c0ad8bbae
wrong type of exit method
7 years ago
01d37e00af
Fix up stepper ISR with linear advance timing ( #10853 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
6f330f397e
[2.0.x] Buffer overflow and scroll fix, UTF8 cleanup ( #10844 )
7 years ago
235facd545
install AVRDUDE 5.10, faster disk find for LPC1768 ( #10849 )
7 years ago
645df23eb0
Fix warning with FASTER_GCODE_PARSER disabled
7 years ago
d74e333c0f
Make sure FAN_ANIM_FRAMES is defined
7 years ago
e2db509d58
[2.0.x] Update/Fix LPC1768 extra script upload_extra_script.py ( #10843 )
...
* Use a different method to find the volume info in Windows
7 years ago
7261f48872
Fix reset of endstops and move state
7 years ago
50fa8e01c1
Minor optimization of axis_did_move bits
7 years ago
a94506ada0
Fix K8400 Y min pos, M118 comment
7 years ago
336a022529
Support Malyan LCD without SD
7 years ago
f28e366b77
Followup for core endstops
7 years ago
8b44745bc7
Clean up and consolidate SD-related code ( #10831 )
7 years ago
9644d56b42
Patches for core motion tests
7 years ago
5f8591528e
Remove #pragmas that don't help c files
7 years ago
230ae6a143
Default G30 to engage / disengage
7 years ago
3e3789da85
Regression: Endstops Core compatibility ( #10823 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
c89649b46e
Suppress U8glib build warnings
7 years ago
bbd09a99f1
32 bit boards classification cleanup ( #10818 )
...
- Ordering and match classification between `boards.h` and `pins.h`
- Check `pins.h` environments
7 years ago
ee333f6be2
Followup to endstops tweaks
7 years ago
d98bc71af7
Boards classification arrangement ( #10814 )
...
STM32 ARM Cortex-M3 boards were listed as M4
7 years ago
4b610b333e
Tweak G38 formatting
7 years ago
d2647c1f19
Fix G1 behaviour after tool unpark
...
Fix #10777 for 2.0.x
Co-Authored-By: Ante Vukorepa <o.orcinus@gmail.com>
7 years ago
3bb950c69a
Fix DEBUG_LEVELING_FEATURE for MBL
...
As noted in #10777
7 years ago
1af98519cd
Group and adjust LCD buttons code
7 years ago
0c3773d724
Cleanup in stepper_indirection.h
7 years ago
4118199ddd
Tweaks to core headers
7 years ago
4b2f6e3b2b
[2.0.x] Add endstop noise filter ( #10796 )
7 years ago
65a004564c
Stepper::set_position needed for some applications
7 years ago
435ecb6b67
Followup to stepper/planner refactor
7 years ago
6dfbb39f83
[LPC1768] Add error-handling to upload script, update autobuild.py ( #10802 )
7 years ago
68d7fcec83
Simplify and fix Z fade height edit
...
Fix #10761
7 years ago
d557c84a71
[2.0.x] Error for FAST_PWM_FAN with 32 bit CPU ( #10798 )
7 years ago
569df3fc0c
Fix interrupt-based endstop detection
...
- Also implemented real endstop reading on interrupt.
7 years ago
a4af975873
Fix planner block optimization
...
- Fixed the planner incorrectly avoiding optimization of the block following the active one.
- Added extra conditions to terminate planner early and avoid redundant computations.
7 years ago
e0ca627033
Planner block HOLD flag
...
Allows the Stepper ISR to wait until a given block is free for use. Allows Planner to plan the first move, which is split into two.
7 years ago
a11eb50a3e
Refactor and optimize Stepper/Planner
...
Better encapsulation and considerably reduce stepper jitter
7 years ago
0566badcef
Add memory barrier, optimal interrupt on-off
...
Disabling an ISR on ARM has 3 instructions of latency. A Memory barrier is REQUIRED to ensure proper and predictable disabling. Memory barriers are expensive, so avoid disabling if already disabled (See https://mcuoneclipse.com/2015/10/16/nvic-disabling-interrupts-on-arm-cortex-m-and-the-need-for-a-memory-barrier-instruction/ )
7 years ago
c2fb2f54a1
Use assembly for AVR ISR vectors
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
206014a957
Fix LPC176x timer functions
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
59f7861bcb
Move backtrace to the HAL folder ( #10790 )
7 years ago
228139eae6
Tweak some LCD comments
7 years ago
7dc03ce721
Simplified fix for babystep pulse width
...
Alternative to the apparently superfluous double delay
7 years ago
65270d6a96
Fix LIN_ADVANCE + SWITCHING_EXTRUDER
...
Followup to #10656
7 years ago
62e2987488
add AT90USB support & add items to popup menu ( #10779 )
7 years ago
9ad42d6617
add delay between pulse edges ( #10778 )
7 years ago
83d42f33e1
Add HAS_HOTEND_OFFSET_Z conditional
7 years ago
3c76bda2d8
Fix switching extruder
...
`DONT_SWITCH` got lost along the way. Replace it with `DO_SWITCH_EXTRUDER` and adjust the code.
7 years ago
c173a31060
Fix some compile warnings
7 years ago
e1d9046efc
[2.0.x] Temperature reading fix ( #10774 )
7 years ago
9b64fdbc3a
[LPC176x] HAL: Add missing program space definition ( #10776 )
7 years ago
50270b53a0
Clear up some more compile warnings
7 years ago
06fd4d7b28
Improve NOMORE, NOLESS, and LIMIT macros
7 years ago
40d7e12827
Removing warnings from compilation
7 years ago
0755fe8ba2
Add FAN_MAX_PWM to example configs
7 years ago
43ddb29f9e
Add FAN_MAX_PWM for M106-controlled fans
7 years ago
0ea60d506a
Clear up LCD-related compile issues
7 years ago
eb2eb72720
Modify UBL mesh_is_valid and use in leveling_is_valid ( #10746 )
7 years ago
b7dfc79988
Disable SERIAL_PORT_2 by default and sanity-check it ( #10748 )
7 years ago
3f6073e23a
Followup tweak to lcdprint_u8g.cpp
7 years ago
fb608938f8
Prevent compilation of unused u8g-oriented code
7 years ago
35258dd50b
Consistent heating status and status reset
...
Fix #10699
7 years ago
37b15fe4cf
Reorder HAL timer header items
7 years ago
836b0bbeee
Fix MBL line_to_destination
...
Fix #10708
7 years ago
ba4c32eec5
Followup to _AXIS patch
7 years ago
d9154ebdf6
Followup to math patch
7 years ago
f07260c33f
Don't babystep on long click unless printing
...
As pointed out in #10731
7 years ago
883b0c9880
Convert custom maths to inlines ( #10728 )
7 years ago
08e36e264e
Apply _AXIS macro
7 years ago
99ecdf59af
Smarter MIN, MAX, ABS macros
...
Use macros that explicitly avoid double-evaluation and can be used for any datatype, replacing `min`, `max`, `abs`, `fabs`, `labs`, and `FABS`.
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
083ec9963e
Tweaks to heater / lcd conditions
7 years ago
9d98a62699
Followup to HAL optimizations and delays
...
- Cleanups, fixes for Due HAL code.
- TC_IER is write-only. Use TC_IMR to test ISR state.
7 years ago
8f8c6a9bc4
Move get_axis_position_mm to Planner ( #10718 )
7 years ago
a1062eec5b
Better handling of DELAY_NS and DELAY_US ( #10716 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
f5aaa2d6c0
Fix some compiler warnings
7 years ago
3614e6ce0f
Fix Switching Extruder with Linear Advance
7 years ago
625035a9ce
Fix M301 access to lpq_len ( #10714 )
...
Co-Authored-By: Zwaubel
7 years ago
1b225a2809
DUE: Emergency parser for the USB CDC
7 years ago
306f0f2135
Move Stepper::synchronize to Planner ( #10713 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
f2e3c9896e
Fix compile warnings in backtrace
...
Part of #10688
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
acacee80a2
Add JUNCTION_ACCELERATION_FACTOR to configs
...
Part of #10688
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
d99f1b2245
[2.0.x] EEPROM code cleanup ( #10710 )
7 years ago
8679f671ed
Remove dependency on PI. ( #10701 )
7 years ago
6671c064cd
Use arc moves for G26 if enabled ( #10696 )
...
Co-Authored-By: ManuelMcLure <manuelmclure@users.noreply.github.com>
7 years ago
325bbbc8c2
[2.0.x] Enable AD595 and AD8495 in concert ( #10693 )
...
* Allow both AD595 and AD8495 in concert
* General temperature code tweaks
7 years ago
c43235dd39
Remove non-special comments
7 years ago
613a3be167
Remove hidden dependencies on destination. Fixes #10686 . ( #10691 )
7 years ago
23a876b08d
Update a comment in motion.cpp
7 years ago
439e0cdd0f
Patch up reverse_pass_kernel (and other planner code) ( #10674 )
7 years ago
fe5c308872
Correction to Printrboard SDSS pin ( #10677 )
...
Co-Authored-By: Simon Swenson <simon-swenson-8351@users.noreply.github.com>
7 years ago
265161ba30
Blink the value for unhomed/unknown axes ( #10670 )
7 years ago
57c2f8d2f6
Trailing whitespace cleanup
7 years ago
b76344c080
More Trinamic cleanup
7 years ago
473c6d3a91
Drop extra RIGIDBOT_PANEL from D6 config
7 years ago
44f3a6dc3b
[2.0.x] Add missing axes to M911, M912 ( #10668 )
7 years ago
722aba77f3
Fix LIN_ADVANCE + SWITCHING_EXTRUDER stepper directions ( #10656 )
7 years ago
a225d2e99e
Fix compilation with UBL and Arc/Bézier
...
Fix #10660
7 years ago
6d9ec1852a
Fix compilation of say_units
...
Fixes #10663
7 years ago
19f189b4e5
Add UBL support for G2/G3 and G5 ( #10648 )
7 years ago
4c663b0216
Add JUNCTION_DEVIATION to example configs
7 years ago
4d4bf7897d
Junction Deviation jerk limiting option
7 years ago
0436e16fb2
Apply shorthand Assembler macros
7 years ago
d1b619be52
Standardize some hexadecimals
7 years ago
ec05408453
Add 3-frame fan animation to bitmaps ( #10654 )
7 years ago
55f1f8446b
Show correct current units in M503
7 years ago
4e16e699c1
Fix sanity checks for dual axes ( #10633 )
7 years ago
a1fab8336e
Fix abort of SD printing
7 years ago
e978e6e782
[2.0.x] Arrange LCD options by type ( #10630 )
7 years ago
8c5bc77fb9
Fix the sanity-check for config versions
7 years ago
1f11b0f612
Fully init planner sync block
7 years ago
f30241bda5
Merge pull request #10614 from thinkyhead/bf2_synced_planner_set_position
...
[2.0.x] Improve sync of planner / stepper position, asynchronous G92
7 years ago
840ff60952
Bring some configs up to date
7 years ago
71cd681473
Add Geeetech i3 Pro C / W examples ( #10626 )
...
Added base example configs for Geeetech's Pro C and Pro W machines.
7 years ago
62e7a9c671
Fix up fwretract handling
7 years ago
bfe223e120
Adjust usage of stepper.synchronize
7 years ago
af1950a63e
Improve sync of stepper positions
7 years ago
0c23792344
Apply int32_t to stepper
7 years ago
c2c02bdc67
Change Max7219 coordinates to traditional (X,Y)
7 years ago
b337698f96
Additional patch for no heated bed
7 years ago
76da6cc544
Fix Ender 2 build volume
7 years ago
81b632c255
Additional temp-oriented improvements
7 years ago
e911635fb1
Add thermocouple with AD8495 support
7 years ago
00e86f1c2d
Add Velleman RGB-LED strip support to K8400
7 years ago
410b023b50
[2.0.x] Add Viki support to RAMPS_FD_V1 (DUE) ( #10598 )
7 years ago
b7e938a9fb
LCD_BED_LEVELING enables a sub-menu for ABL
7 years ago
a90d99c27c
Rename float32 => float52, etc.
7 years ago
d7b699ec34
Fewer includes of vector_3.h
7 years ago
9312636ee4
Ender-3 config files ( #10585 )
7 years ago
05fca752d6
Clean up autostart handling
7 years ago
c87b0e21be
Add units to probe speed comments
7 years ago
2c1205d8b1
Improve debug of homing move feedrate
7 years ago
c8e4b7c8a6
Fix XY homing move away rate
7 years ago
05c33833e7
[2.0.x] Add NO_LCD_MENUS option ( #10582 )
7 years ago
524cc392f4
Fix sd_status comparison
...
Co-Authored-By: perkmeister <perkmeister@users.noreply.github.com>
7 years ago
1f92b9a4ed
Fix do_probe_move with fr_mm_s ( #10576 )
7 years ago
a73cece360
Fix utility.cpp for DEBUG_LEVELING_FEATURE
...
As mentioned in https://github.com/MarlinFirmware/Marlin/issues/9429#issuecomment-385305597
Co-Authored-By: Jack Bradach <jack@bradach.net>
7 years ago
4dfc011d86
Fix homing with probe feedrates
7 years ago
59fda986ea
Allow Z_AFTER_PROBING to be 0
7 years ago
63e4afc910
Do rounding in integer (instead of FIXFLOAT)
...
Co-Authored-By: Bob-the-Kuhn <bob-the-kuhn@users.noreply.github.com>
7 years ago
616651ff23
Add sanity check for LED_CONTROL_MENU
...
Addressing #10569
7 years ago
9e0d99c0c6
Round all floats in string conversion functions ( #10566 )
7 years ago
3f68203324
Modify FastIO error message
7 years ago
1dab44213a
Fix the TMC26X initializer CS pin argument
...
From #10531
Co-Authored-By: chriscg9 <chriscg9@users.noreply.github.com>
7 years ago
cd08f01bb4
Fix M421 comment in gcode.h
7 years ago
7546f87949
Allow a home bump of 0 when homing Z with probe
7 years ago
d470a1234f
Fix ENABLED/DISABLED for DUE
...
…and any other platforms where `false`/`true` are defined as `0x0`/`0x1`.
This fixes issue #10550 .
7 years ago
683dc24e0f
When homing with Z probe bump at Z_PROBE_SPEED_SLOW
7 years ago
8db7fb226a
Fix M420 C for UBL
7 years ago
ed8d2bc225
Clean up some endstop inverting examples
7 years ago
c7305be4d2
Fix some endstop inverting settings
7 years ago
f973ff49ae
[2.0.x] MKS SBASE - Separate SD_DETECT for LCD and on-board SD cards ( #10557 )
7 years ago
5ac226aa93
Further cleanup of inline delays
7 years ago
724e9f56c8
Removed "const" to match parser. ( #10548 )
7 years ago
2e1939e85c
[2.0.x] report error on unsupported commands ( #10553 )
...
Raise an error when an unknown/unsupported G/M command is requires.
This will address #10546
7 years ago
a474a7e675
Correct AVR_ATmega328_FAMILY macro
...
…as with #10540
Co-Authored-By: per1234 <per1234@users.noreply.github.com>
7 years ago
f790b4bc0a
Reorganize some conditionals
7 years ago
a51ba6e3f6
Fix ABL grid bounds test for Delta/SCARA
...
Addressing #10538
7 years ago
df6bc812b5
Fix disable of Z_HOMING_SENSITIVITY for HOMING_Z_WITH_PROBE
...
As pointed out in #10532
7 years ago
63e0b36f8b
Fix G29_RECOVER_COMMANDS typo
7 years ago
f83361a814
Apply const to tmc_sensorless_homing
7 years ago
212e52e485
Basic delay for Max7219 on ARM
7 years ago
7b6e742436
Wrap delay macros in do{}while(0)
7 years ago
58ca3be1ec
delayMicroseconds() cannot be called in critical section ( #10535 )
...
on the STM32 platform
7 years ago
00dfaae8df
[2.0.x] Platformio - automate build & environment selection ( #10503 )
7 years ago
299c4fed42
Undefine PIDTEMPBED without a bed heater
7 years ago
456cf971af
HAL FastIO cleanup and fixes
7 years ago
5b5e322356
Set Interrupt Priorities and Grouping for STM32F103. ( #10517 )
7 years ago
0e450df6a2
MKS OLED support for RUMBA
...
Based on #10519
Co-Authored-By: Alex <alex18881@users.noreply.github.com>
7 years ago
2578996631
[2.0.x] Emergency parser for multiple serial ports ( #10524 )
7 years ago
8cc31d1b2e
Cleanup to emergency parser
...
Followup to #10516
7 years ago
2242b98248
[LPC176x] Emergency Parser Feature ( #10516 )
7 years ago
eef0248a1c
Add M420 C to adjust the whole mesh ( #10522 )
7 years ago
c1e5ebbc1e
[2.0.x] AVR: Atomic bit set and clear of upper pin ports without critical section ( #10502 )
...
* AVR: Atomic bit set and clear
The critical section can be dropped, saving 3 cycles per access. Also simplified pin toggling for all ports.
7 years ago
02a711c4d6
[2.0.x] Fix crash upon repeated calls to process_subcommands_now_P ( #10509 )
7 years ago
a3ce8a3fcd
Add sanity checks for EMERGENCY_PARSER
7 years ago
f06c3c38b9
Fix M0_M1 with no LCD
7 years ago
c82dd5129f
Revert potentially-not-redundant UBL test
...
Response to #10435
7 years ago
9789c1c719
Fix current_temperature_chamber compile error
...
Fix #10505
7 years ago
0c428a66d9
Proper AVR preemptive interrupt handling ( #10496 )
...
Also simplify logic on all ARM-based interrupts. Now, it is REQUIRED to properly configure interrupt priority. USART should have highest priority, followed by Stepper, and then all others.
7 years ago
f423e54f77
Strip trailing spaces
7 years ago
8177c4334e
Merge pull request #10498 from xC0000005/MalyanLCDFix
...
Fix overridden Malyan LCD functions
7 years ago
cb46cb8480
Add HAS_HEATED_BED conditional ( #10495 )
7 years ago
10a25f733e
Add SENSORLESS_HOMING to Archim 2.0 ( #10500 )
7 years ago
24d23ce49b
Fix function definitions for Malyan LCD
7 years ago
ad58b626a3
Fix pin mappings for Viki2 on Azteeg X5 GT ( #10487 )
7 years ago
9e07df5c1b
Extra options for LEVEL_BED_CORNERS ( #10483 )
7 years ago
1c3d49afe0
Fix G28 with Z_AFTER_PROBING
...
Fix #10476
7 years ago
b6747c742a
Cleanup AZTEEG_X5_GT pins for VIKI
...
What should the SD detect and SDSS pins be? Followup soon on #8138
7 years ago
023385ca59
Merge pull request #10479 from thinkyhead/bf2_creality_power_loss_resume
...
[2.0.x] Creality3D Power-Loss Recovery
7 years ago
3396671011
[2.0.x] Reset LCD status to fallbacks ( #10470 )
...
* Remove obsolete strings
* Tweak some static consts
* Reset LCD status to fallbacks
7 years ago
d58450c82a
Russian language update
...
Co-Authored-By: anton-piliugin <34044202+anton-piliugin@users.noreply.github.com>
7 years ago
11ab017dd0
Creality3D Power-Loss Recovery
7 years ago
594d6f9efd
Add POWER_LOSS_RECOVERY to example configs
7 years ago
Scott Lahteine