8be91677df
Fix Skew factors ( #12555 )
...
- Ensure Skew factors are calculated from test square measurements
6 years ago
03ef2d6c82
Fix "paused" message and M125 called by M25 ( #12551 )
6 years ago
95d154a91f
Fans loop macro
6 years ago
61db0b65b6
Followup to heating progress
6 years ago
4f9ec9ab45
Add heating progress bars ( #12543 )
6 years ago
929a513a6b
Add poll_runout_states, which returns 1 for runouts ( #12547 )
6 years ago
01b5c810d5
Space out multiple edit lines a bit
6 years ago
cd88ea2106
Fix runout debug output
...
Followup to #12544
6 years ago
cecc238f68
Save recovery info on SD pause
6 years ago
439a3e8463
Improve runout sensor, fix LIGHTWEIGHT_UI screen size ( #12544 )
6 years ago
5b24ce9024
Hide M217 compile warning
6 years ago
d94b50a3d8
Add sample config for Delta with MKS SBASE ( #10819 )
6 years ago
dec721c52b
Add Formbot Raptor2 and Raise3D pins ( #12532 )
...
* Add Formbot Raptor2 board
* Add Raise3D Rumba board
6 years ago
6aae199572
Add missing boards to Makefile
6 years ago
0a638cc022
Adjust Formbot Raptor pins
6 years ago
e5019a0481
Fix English special symbols ( #12529 )
6 years ago
09d6db491a
Fix wait_for_bed compile error
6 years ago
d545f984b0
Update Slovak translation ( #12523 )
6 years ago
730f223100
Correct FANMUX2_PIN ( #12538 )
6 years ago
d857cdfb27
Update Turkish language ( #12524 )
6 years ago
4a7c6f7241
NUM_ARRAY => COUNT
6 years ago
31113c5adf
Update Italian language ( #12512 )
6 years ago
b57343c255
Put status screen options in Configuration_adv.h
6 years ago
1fcc13b011
Allow Serial Overrun Protection to be disabled
6 years ago
29c53f2402
Hide some compile warnings
6 years ago
caca3c8503
Use wait_for_bed with WAIT_FOR_BED_HEATER
...
Addressing #12517
6 years ago
f1efcfed14
Fix backslash in language_test.h
6 years ago
3b186a55ac
Don't show superscript ³ with NOT_EXTENDED_ISO10646_1_5X7 ( #12513 )
6 years ago
82c96c971e
Bring superscripts slightly lower in BDF fonts
6 years ago
8a0992d921
Fast PWM for controller fan ( #12485 )
6 years ago
e98d195901
Remove extra declarations in cardreader.cpp ( #12520 )
6 years ago
fd2998efd5
Revert ADC_KEYPAD direction behavior ( #12508 )
6 years ago
d29cb09b3e
Fix a minor compile warning
6 years ago
5b1d52671c
Use superscript 3 in language_en.h ( #12504 )
6 years ago
7109dadd21
Additional pin definitions for Archim 2 ( #12500 )
...
- Added GPIO pins to Archim 2
- Added new 108 pin to `fastio_Due.h`
6 years ago
4975b13b74
Fix problems with LPC1768 EEPROM flash emulation ( #12503 )
...
* Remove duplicate calls to PrepareSector
Some flash memory API calls require that a call to `PrepareSector` is done before use. However this call is already made by the LPC1768 framework so the calls in this code are not required.
* Ensure correct alignment of RAM buffer
The LPC176X flash API requires that the RAM buffer used for write operations must be word-aligned. This change ensures that this is the case.
6 years ago
b738972e69
General cleanup of Re-ARM pins
6 years ago
ee423dcdd0
Invert hotend bitmaps, by default
6 years ago
c5642a894f
Fix ADC_KEYPAD middle button ( #12493 )
6 years ago
0946cbcdca
Revert some const changes (for now)
6 years ago
4def8b3b5e
Expanded options for _Statusscreen.h ( #12455 )
...
See the PR for full details. The updated system will be documented on the website in the near future.
6 years ago
d51e5690f4
Don't show updir with no card present
6 years ago
ec9d21a234
Shift YZ on graphical display to fit Z+123.45
6 years ago
817a37169a
Apply/unapply const here and there
6 years ago
643e0066a0
Followup to #12451
6 years ago
4bcb63b705
Fix for #12482 ( #12483 )
...
Fix Z-move to uninitialized position in SWITCHING_EXTRUDERS tool_change (no_move=true)
6 years ago
50ee747787
Fix compilation errors. Followup to #12439 ( #12481 )
6 years ago
90a58488b5
Corrected unused var, default switch, Travis tests ( #12477 )
6 years ago
a4c15dc54f
Modify MBL to use IJ instead of XY ( #12478 )
6 years ago
fc3f1c4572
Get u8g reference for lcdprint
6 years ago
88c57eaf55
Clean up some u8g code ( #12476 )
6 years ago
1f93d2bcf7
Fix LCD compile error, etc. ( #12472 )
6 years ago
826d570162
Combine Travis CI option-setting commands ( #12474 )
6 years ago
9d13f07d09
GTM32 Pro VB changes from Markku Sinisalo
6 years ago
5fbe5cabc8
Fixed displaying of kill MSG_OUTAGE_RECOVERY string. ( #12470 )
6 years ago
4ae9a06c60
Update M303.cpp ( #12471 )
6 years ago
c0b75f49b6
Fix "no effect" and "unused variable" compile warnings ( #12473 )
6 years ago
5a4fd8e0a6
Fix access to the DWT peripheral for STM32 HAL ( #12434 )
...
Access to the DWT peripheral for the `CYCCNT` register needs to happen before `main()`. The code needs to be called after the setup of the system clocks, so the right place is between the `premain()` and `main()` function of the STM32 Arduino core.
This patch moves the DWT access code to a new function, which is then placed between `premain()` and `main()`.
6 years ago
7f225b9421
Fix MAX_MESSAGE_LENGTH
6 years ago
06674a321a
Remove extra include
6 years ago
c1e17037e5
Various fixes for MarlinUI and ExtUI ( #12439 )
6 years ago
d3605cfc26
Don't start watching heaters when target is 0 ( #12453 )
6 years ago
93e958f695
Fix compile error with ZONESTAR_LCD+NO_LCD_MENUS ( #12466 )
6 years ago
22d7fed60a
Fix compile error with SD_FIRMWARE_UPDATE ( #12462 )
6 years ago
779b2709ec
Change temperature pin order for RemRam V1 ( #12458 )
...
Beta testers suggested to adopt the RAMPS order of temperature probe connectors. This commit fixes the order to the RAMPS order.
6 years ago
8ebb4dc294
Followup to static CardReader
6 years ago
7ee5894360
Allow float XY probe offsets
...
Responding to #12383
XY probe offsets should be integers because adding decimal points makes the code larger. But if decimals are very much wanted, this commit removes the old restriction.
6 years ago
43ecdb606f
Fix a compile warning ( #12452 )
6 years ago
984c4ba8c7
Enable SD Card on RepRap Display and RADDS ( #12446 )
...
* Enable SD Card on RepRap Display and RADDS
Define the necessary pins in `pins_RADDS.h` (copied from the `RADDS_DISPLAY` section) for the use of the SD card slot on RRD.
6 years ago
56a94c2a26
Use 'target_extruder' in M104 as with M109 ( #12448 )
6 years ago
66580f32c2
Make CardReader class static ( #12451 )
...
* Make CardReader a static class
* Make CardReader flags into bitfields
6 years ago
3e9ffaddb6
Consolidate, optimize some LCD menu code ( #12450 )
6 years ago
d97e31db4c
Optimize Power-Loss Recovery ( #12440 )
6 years ago
ca21ac6b9b
Support two MAX6675 thermocouples ( #8686 )
6 years ago
0e610815e4
No need for Cap:PAREN_COMMENTS
6 years ago
7a075a5dc9
Tweak extruder errors
6 years ago
2d92f333f5
Fix GcodeSuite::T active_extruder reference
6 years ago
d2bb53702a
Optimize target_extruder, ignore T with mixing ( #12432 )
...
* Optimize target_extruder, ignore T with mixing
* Give G-code Tn parity with tool_change
6 years ago
5e586a6b39
Fix to runout sensor code. ( #12431 )
...
- "old_state" is no longer a class static variable.
6 years ago
d82c350de7
Miscellaneous LCD code renaming, reordering ( #12430 )
...
* Move special characters to language.h
* Apply some naming standards
* Clean up menu item draw functions
* Rename some Temperature methods
* UI => ExtUI
6 years ago
edfd106bc5
Rejigger Filament Runout class ( #12428 )
6 years ago
f4c128ecaa
Move RRW keypad code to a common method ( #12429 )
6 years ago
54ec5528a0
hasstatus => has_status
6 years ago
ebf585b673
Fix an old sanity check
6 years ago
052d102ded
UltiMachine Archim 1 support ( #12404 )
6 years ago
664e20754d
Clean up pins files
6 years ago
1eb5249598
Fix Formbot Trex-2+ configs
...
Followup to #12422
6 years ago
075a22ed65
Update Portuguese-Brazilian translation ( #12402 )
6 years ago
3ceab8474c
Add required "cardreader.h" include ( #12419 )
6 years ago
98c2fc4e42
Endstops fix followup ( #12423 )
...
Followup to #12413
6 years ago
f19fd642ce
Updates to Formbot T-Rex 2+ configuration files ( #12422 )
...
Updates to Formbot T-Rex 2+ configuration files
6 years ago
cda5ef08fa
Debug of G2-G3 for UBL ( #12386 )
...
Changes only affect UBL. Everything else is left alone.
6 years ago
9ad3aed0ef
Fix tool-change for MIXING_EXTRUDER with < 2 virtual tools ( #12417 )
...
Fix #12416
Better handling of `ENABLED(MIXING_EXTRUDER) && !MIXING_VIRTUAL_TOOLS > 1` - to not fall through to the general case. Fix compiler warnings for `#elif EXTRUDERS < 2`.
6 years ago
d631267548
Refine endstops fixes ( #12413 )
...
When endstops/probe are enabled `ENDSTOP_NOISE_THRESHOLD` calls to `update` are required to properly re-sync endstops/probe status.
6 years ago
0ee1a92971
Group status methods, share reset_status with Extensible UI ( #12414 )
...
* Group status methods, share reset_status with Extensible UI
* Move common DOGM code to headers
6 years ago
690c4e8457
Clean TLM trailing whitespace
6 years ago
143b2896e0
Add M412 to enable/disable filament runout detection ( #12406 )
6 years ago
a163c89c6a
Followup to 50af1d1
6 years ago
be6271767f
Fix BABYSTEP_ZPROBE_OFFSET ( #12408 )
...
Fix #12399
Did not compile without `WATCH_HOTENDS || WATCH_THE_BED`.
Add condition to include "../../module/temperature.h".
6 years ago
50af1d1e08
Differentiate translated On/Off from Serial ON/OFF
6 years ago
df907a905f
Update UBL comments for debug change
6 years ago
da17f8ad37
For now (!) don't synchronize in M204 and M205
...
See if this has any deleterious effect on motion planning by slicers that inser their own jerk and acceleration controls. The problem I see is that these settings can take effect on blocks already in the planner, and the only way around this would be to shadow these settings in planner blocks and use the shadowed settings in the planner.
6 years ago
a3923424c7
Clean up LCD width/height determination
6 years ago
a0c795b097
Encapsulate common display code in a singleton ( #12395 )
...
* Encapsulate common LCD code in a singleton
* Depend more UBL code on UBL_DEVEL_DEBUGGING
- Since most users don't need the debugging on at all times, this helps reduce the default build size for UBL by over 2K, a little closer to fitting on 128K boards.
6 years ago
9da6809ac3
Adjust some comment spacing
6 years ago
471f403a67
Reduce code size with plain inlines
6 years ago
30a49f5ee2
Apply extra condition to LCD_PROGRESS_BAR
6 years ago
4e0c935959
Update HAL and libs formatting
6 years ago
47483e8c17
Update Raptor config
6 years ago
6093df11dc
Allow G26 to use the active extruder ( #12387 )
...
* Make lcd_quick_feedback argument optional
* Add click_to_cancel option to wait_for_hotend/bed
* Have G26 use the active nozzle and wait_for_hotend/bed
* Use wait_for_release in UBL G29
* Add 'T' parameter to G26 for an initial tool-change
6 years ago
4260282df7
Tevo Little Monster example configuration ( #12370 )
6 years ago
bed15fcd81
Tweak 'echo_not_entered' used by MBL's G29
6 years ago
c239131ff5
Use 'serial_spaces' in 'print_2d_array'
6 years ago
56150ec030
Add reference comments to MeshLevelingState
6 years ago
24c5e57bb6
Update German language ( #12379 )
6 years ago
fd7fd55662
Solve endstops issues ( #12382 )
...
- Partially reverts #11900 and tries to solve #12336
6 years ago
78ccedd6a8
Fix M91x sanity-check to permit TMC2660
...
Fix #12362
6 years ago
b60abc7c37
[2.0.x] Macro G-codes ( #9365 )
6 years ago
ccdbf20f60
Update Italian language ( #12368 )
6 years ago
d08847b1a6
Update Slovak translation ( #12376 )
6 years ago
7665dff58b
No error on T0 with single-extruder and fix MIXING_EXTRUDER virtual tools ( #12375 )
6 years ago
4ed6397e5d
More comprehensive NO_LCD_MENUS ( #12367 )
6 years ago
9c8f083d6c
Extend pins errors to include the processor
6 years ago
525ea554a1
Remove obsolete comments
6 years ago
ef724edd80
Apply HAS_LCD_MENU in EEPROM code
6 years ago
b169320a03
Clean trailing whitespace
6 years ago
81b1e9d272
Fix up xdiff, ydiff, zdiff in tool change
...
Followup to #12137
6 years ago
6471a75a22
Combine more tool-change variables ( #12137 )
6 years ago
147e270208
Restore GTM32_PRO_VB temp and heater pins
...
Undo #12345
6 years ago
8def25e475
Set CUSTOM_MACHINE_NAME for some configs
6 years ago
812f6a7dd7
Fix Resume from SD Pause
...
In reference to https://github.com/MarlinFirmware/Marlin/pull/12098#issuecomment-436231690
6 years ago
4f72e041f2
Use card.stopSDPrint() for completeness
6 years ago
488a17b3f5
Use IS_SD_PRINTING() more
6 years ago
4dbaa6369f
Fix const pointer assignment compile error ( #12350 )
6 years ago
959ed32636
Update Italian language ( #12352 )
6 years ago
812bfec65e
Update Slovak translation ( #12354 )
6 years ago
1624722566
Update German translation ( #12355 )
6 years ago
e574f01568
More advanced pause tweaks ( #12356 )
...
* Followup to LCD_TIMEOUT_TO_STATUS=0
* Make continuous purge screen fit 20x4
* Unify purge message modes
* Preserve last-set pause header mode
6 years ago
5a470d4a49
Apply some tool-change cleanup
6 years ago
34ea458667
Fixed advanced pause messages ( #12353 )
6 years ago
4c5ca89d8c
Show the appropriate pause message ( #12348 )
6 years ago
8517d5f915
LCD menu code refactoring and cleanup ( #12308 )
6 years ago
b3b4e6dc45
Change Marlin debug flag names to fix conflicts ( #12340 )
...
In reference to #11000
6 years ago
f7e682eeee
Update Italian language ( #12344 )
6 years ago
a813900fce
Add Geeetech Rostock 301 config, update GTM32 Pro VB pins ( #12345 )
6 years ago
04f173790f
Remove trailing whitespace
6 years ago
c536ee1122
Clean up bq Zum Mega 3D pins
6 years ago
c31e1735dd
Restore LPC1768_PIN_INTERRUPT_M, apply to Z3
...
- In reference to #12166
6 years ago
93d5b945dd
Hide mesh editing until a valid mesh exists
6 years ago
f34f09c821
Update German language ( #12336 )
6 years ago
eefd7676a3
Updated slovak translation ( #12338 )
6 years ago
486f2a66a9
Fix MBL XY parameter error messages
...
Fix #11522
6 years ago
2613ddf61c
Fix "circle"
6 years ago
b779b42ffd
Prevent current step-down going negative
...
Addressing #11348
6 years ago
427bc64ba1
G28 O respects HOME_AFTER_DEACTIVATE
...
Addressing #11271
6 years ago
3866aeac52
Clean up ENCODER_RATE_MULTIPLIER config
6 years ago
498dfa291e
Update and fix CHDK
6 years ago
fed84f2961
Use multiplier edit item for mesh point editing
6 years ago
d5ab4cd22a
Provide a default for Z_PROBE_LOW_POINT
6 years ago
3cbc3ecdd7
Fix 'M43 T' to use 'L' as last pin
...
- The documentation is correct. The code was wrong.
6 years ago
1769249876
Recommend keeping endstops off
6 years ago
5182eaf661
Fix endstops enable behavior during probing
...
Fix a bug introduced in #9582
6 years ago
07a0822ebe
M420 support in MARLIN_DEV_MODE
6 years ago
63be48ada6
Add MESH_EDIT_MENU to example configs
6 years ago
82ff7c6542
Add a mesh edit menu for MBL / ABL-Bilinear
6 years ago
44fa7fb18c
Cleanups for leveling-related code
6 years ago
cc2bc67440
ENABLED(NEWPANEL) => HAS_LCD_MENU
6 years ago
fc84878cba
MSG_UBL_EDIT_MESH_MENU => MSG_EDIT_MESH
6 years ago
cd066bfeba
Extend error messages for E factors sanity-checks
6 years ago
c10edb0998
Update, correct sanity-checks for up to 6 extruders ( #12333 )
6 years ago
0c85869c26
Clean up file endings
6 years ago
b99f0776d6
Clean up some U8G files
6 years ago
8014e1cc9d
Allow disable of LCD_TIMEOUT_TO_STATUS (when 0)
6 years ago
bd05816fd8
Update Italian language ( #12327 )
6 years ago
3c21483c88
Provide DOGLCD SPI pins for MKS SBASE + VIKI
6 years ago
e0956bb572
Drop 'register' storage specifier
6 years ago
c04cf127f7
Fix EEPROM servo angles init, section grouping
6 years ago
9c0e05552e
Suppress some compile warnings
6 years ago
176654791e
Use board-specific or platform SPI pins in HAL_STM32 ( #12323 )
6 years ago
60dbd8161c
Fix VMAX editing
...
Fix #12326
6 years ago
b7ca93ba37
Remove dead comment
6 years ago
608be966d7
Add servos to pins_FYSTEC_F6_13.h
6 years ago
67b22760d9
Return to status to show manual deploy/stow messages ( #12324 )
6 years ago
f5e8e8b53d
Fix broken LPC176x build ( #12317 )
...
* Fix broken LPC176x build
* Add UBL+HD44780 test for LPC1768
6 years ago
f5eab912ed
Apply #pragma once, misc cleanup ( #12322 )
...
* Apply #pragma once in headers
* Adjust some thermistors formatting
* Misc cleanup and formatting
6 years ago
8696f882a9
Merge pull request #12313 from thinkyhead/bf2_scara_home_offset
...
Revive SCARA home offset (not fully implemented)
6 years ago
56d2dcb184
Use first_page flag in place of page.page == 0
6 years ago
d1ff22b983
Revive SCARA's home offset (unimplemented)
6 years ago
2c9586be0c
Clear up HAS_WORKSPACE_OFFSET meaning
6 years ago
6e3caf23b6
IS_DELTA => ENABLED(DELTA)
6 years ago
19f49db96f
Tweak / reduce menu items
6 years ago
e4cf175163
Synchronize on M204, M205 ( #12302 )
...
* Add parser.seen for multiple parameters
* Fix M666, use !seen for report
* Synchronize on M204, M205
6 years ago
5ba6607181
Fix keypad-related compile error ( #12306 )
6 years ago
2fb2e286ee
Followup to #12256
6 years ago
3eb9838dca
Simplify TMC sanity-checks
6 years ago
f5b31e218d
Followup to #12082
6 years ago
31c28d0dd2
Drop pgm_read_*_near and let headers choose ( #12301 )
...
- Drop `pgm_read_*_near` and let headers choose.
- Define `USE_EXECUTE_COMMANDS_IMMEDIATE` as a conditional.
- Add `process_subcommands_now` for SRAM-based commands.
6 years ago
fce150f094
inline static => static inline
6 years ago
323c088356
Restore LED light color after pid tuning ( #12082 )
6 years ago
9f77df2590
Followup to menu refactor. TMC warnings, sanity. ( #12288 )
...
- Followup fixes for menu refactor
- Fix TMC sanity checks, unused var warnings
6 years ago
cafabf2055
Implement DELAY_NS with CYCCNT on Cortex-M7 ( #12283 )
6 years ago
f5498168ae
Ensure PENDING/ELAPSED use a 32-bit integer
6 years ago
6e041b9c61
Use blink to show more info on LCD ( #12256 )
6 years ago
eb5600acd2
Add parentheses to LCD_CLICKED
6 years ago
42f8b6c530
Make M125 work with SDSUPPORT ( #12289 )
6 years ago
f319087372
Followup to #12293
6 years ago
74bbb13008
Fix Mixer calculations for 32-bit processors ( #12293 )
6 years ago
549d11225a
Add to description of Z_STEPPER_AUTO_ALIGN
...
In response to #12272
6 years ago
2cff0d1f39
Move menu_level_bed_corners to its own file
6 years ago
44f2a82a56
Move axis_homed, axis_known_position to motion.*
6 years ago
946cf8b453
EEPROM read code grouping
6 years ago
f2adb4b9cc
Update German language ( #12280 )
6 years ago
484ca68228
Fix misplaced parentheses ( #12284 )
6 years ago
1d366db764
Tweaks to CR-10S configuration
6 years ago
b5d7f69b51
Followup to #12249
6 years ago
b780b69c62
Use font ascent and descent for line positioning ( #12224 )
6 years ago
9cd3529108
Organize language data, fix Korean and Danish
6 years ago
66d44c72c3
Add fast binary file transfer to SD card option ( #12249 )
6 years ago
72d8adfd1e
Cleanup and refactor EXTENSIBLE_UI ( #12227 )
...
- Add `axis_t`, `extruder_t`, `heater_t`, and `fan_t` to eliminate ambiguity, improve type safety.
- Regularized getter/setter argument order and naming.
- `setAxisPosition` no longer stacks moves in the buffer, allowing it to be called repeatedly on each touch ui tap.
- Implement better manual moves for `EXTENSIBLE_UI` (#12205 )
- Calling `setAxisPosition_mm` no longer buffers the entire move to the new position, but instead causes small moves towards it to be made during the idle loop. This allows the user to adjust the destination even after the move has started and makes the UI feel much more responsive.
- As suggested by @ejtagle, the new code keeps the planner buffer full to ensure smooth motion without stops and starts.
- Change `En`, `Hn` and `FANn` to zero-based indices.
- Labels consistent with the rest of Marlin code.
6 years ago
1946f729fd
STM32 FastIO using register access ( #12276 )
6 years ago
56057bcecd
Fix lcd_impl_status_screen_1
6 years ago
4ed579cafc
Americanized English spelling
6 years ago
9e663a624b
Apply #pragma once to configuration files
6 years ago
98c32d8df1
Fix a config endif label
6 years ago
3583e2b449
Followup to Menu Refactor ( #12275 )
6 years ago
5536228359
G34 Auto-align multi-stepper Z axis ( #11302 )
6 years ago
f9b80e7217
Make getfilename_sorted standard for listings
6 years ago
5ead026967
Fix menu_temp_xx_filament_change menu items
6 years ago
d632e44c8c
[Merge] Refactor LCD menus / screens ( #12199 )
6 years ago
1f9806875c
Update German language ( #12261 )
6 years ago
63ce8baa55
Fix Teensy 3.5/3.6 ADC access for ADC1 ( #12258 )
6 years ago
3a935fd72b
Reduce repetition in menu edit items
6 years ago
b063b1b722
Reorganize includes and declarations
6 years ago
43cf913048
Move SD Card Menu to its own file
6 years ago
0161d3f733
Move Custom User Menu to its own file
6 years ago
3b0d2330b6
Move Delta Calibrate Menu to its own file
6 years ago
6896847210
Move LED Menu to its own file
6 years ago
9cd5471202
Move Job Recovery Menu to its own file
6 years ago
9f11e0284c
Move Filament Change Menu to its own file
6 years ago
d87ab3ed20
Move Advanced Settings Menu to its own file
6 years ago
587a64d80c
Move Bed Leveling Menu to its own file
6 years ago
96f313fb41
Move Info Menu to its own file
6 years ago
423ab029b2
Move Temperature Menu to its own file
6 years ago
489017995e
Move UBL Menu to its own file
6 years ago
a489c9fa52
Move Motion Menu to its own file
6 years ago
3a9ad9f2b1
Move Configuration Menu to its own file
6 years ago
143d4ec043
Move Tune Menu to its own file
6 years ago
829effc1fe
Move Main Menu to its own file
6 years ago
37ff663b02
Convert LIGHTWEIGHT_UI to CPP
6 years ago
a964f098b3
Make dogm status screen a CPP
6 years ago
8055ed24ff
Move font data to a subfolder
6 years ago
774a6e8199
Drop TALL_FONT_CORRECTION
6 years ago
c825c419d4
Convert DOGM / HD44780 impl to CPP files
6 years ago
182b1405d9
LCD conditionals in configurations
6 years ago
2bf18950ab
Refactor LCD menus
6 years ago
ac5f2762b7
Use E_AXIS_N where possible
6 years ago
6fbc87301f
'G29 H' to set a centered square probe area (linear, bilinear) ( #12242 )
6 years ago
c1e8bd6add
Remove STM32 board-specific delays ( #12243 )
...
...and replace with delays for all HAL_STM32 boards.
6 years ago
3c9daf322a
MSG_CNG_SDCARD => MSG_CHANGE_SDCARD
6 years ago
4b7a0a5b39
Require TMCStepper 0.2.2 or newer
...
In reference to #12175
6 years ago
ab8425f1b5
Clean up PROBE_TRIGGERED_WHEN_STOWED_TEST ( #12232 )
6 years ago
3028a620af
Add RACK_AND_PINION_PROBE ( #12218 )
6 years ago
ad60f0691c
Add Creality3D RAMPS pins definitions ( #12229 )
6 years ago
5580773191
Use FastIO, sanity-check LPC SD options, apply formatting ( #12231 )
6 years ago
d015f746cc
Fix some compile warnings ( #12220 )
6 years ago
dacb5324e8
Fix display of Y on Graphical LCD
6 years ago
bf9dd4f4cf
Add helpers for custom text in menu items ( #12214 )
...
For some features it can be useful to write custom text in a menu item. This commit provides helpers to make this easier.
6 years ago
e8031b1152
Add Custom Microstepping options
6 years ago
fbfb48cce0
Indent a block
6 years ago
1a00d1bdaf
Add pullup to USB interrupt line
...
- A pullup on the INT pin is required when the pin is level-active
6 years ago
a07ac6312f
G0 feedrate may be fixed or variable ( #12172 )
6 years ago
53c535a0c1
Remove trailing whitespace
6 years ago
55dec02ca1
Allow X, Y, Z manual move when cold. ( #12209 )
6 years ago
7243101135
z_offset fix for deltas ( #12210 )
6 years ago
9613f00877
Fix getProgress_seconds_elapsed to return seconds
6 years ago
5d487ef40e
Fix null exception due to duration_t of zero ( #12207 )
6 years ago
a9061714f2
Update Italian language ( #12196 )
6 years ago
aebbb2359d
Fix IDEX homing X0 wrong direction ( #12200 )
6 years ago
0a549fd1f2
Fix EXTENSIBLE_UI compile errors ( #12206 )
6 years ago
a80ba8fc6e
Slovak translation update ( #12202 )
6 years ago
e48cbff10d
Fixed redefinition warnings of MSG_HOTEND_TOO_COLD. ( #12203 )
6 years ago
7a04eb3a8b
Fix some comment formatting
6 years ago
2f873a119f
Revert some UBL strings
6 years ago
a93e9e6e9b
Use preheat labels in place of PLA/ABS ( #12194 )
6 years ago
aa72884a6e
Enable use of SERIAL_PORT_2 on HAL_STM32 ( #12197 )
6 years ago
46360f18b4
Bring thermistor_75.h up to speed
6 years ago
e229b831fa
Customizable preheat labels
6 years ago
a553ab82e0
Add e index to _lcd_move_distance_menu
6 years ago
3a46212dd8
Better cold extrusion prevention in LCD menu ( #12189 )
6 years ago
fc31da1114
Implement custom delay/millis for EXTENSIBLE_UI ( #12188 )
6 years ago
3a3ab3391f
Return set_directions() to stepper.cpp ( #12182 )
...
Initial manual Z move can be negative if your stepper is inverted. Leads to bad situations for crashed or initially booted printers.
6 years ago
e5ae7a07d1
Suppress compiler warning
6 years ago
6ee2af5e2d
Simplify pins_TRIGORILLA_14.h ( #12162 )
6 years ago
d801f85963
Correct EEPROM read/write disparities. ( #12169 )
6 years ago
8d3a92fc4a
Followup to millis_t patch
6 years ago
44369d536a
Use millis_t where needed ( #12152 )
6 years ago
b641571098
Replace types.h with millis_t.h
6 years ago
eeef4e630a
Fix compile error in leds.h
6 years ago
9969c06cb5
Fix compiler warning
6 years ago
427c80119a
Hide some menu items when busy: fix typo ( #12164 )
6 years ago
55ac2f4c23
Fix filament runout for idex duplication modes ( #12168 )
6 years ago
b640b3b0d6
Define ST7920 delays for board ARMED ( #12161 )
6 years ago
2e5e689a7f
Fix kill() and ExtensibleUI ( #12160 )
...
* Fix to isPrintingFromMedia()
- isPrintingFromMedia() will now return true even if SD print is paused.
- isPrintingFromMediaPaused() allows UI to determine if the print is paused.
* Don't use _delay_us in minkill (#12145 )
- In HAL_DUE, _delay_us is simply an alias for delay, which causes the board to hang and subsequently reboot due to the watchdog timer.
* Shorten code with IFSD macro
6 years ago
b381cad399
Clean up trailing whitespace
6 years ago
9090065e9f
Move EXTRA_FAN_SPEED above FWRETRACT
6 years ago
4eb798dbdc
Add support for Arm'ed (STM32F4) board ( #12147 )
6 years ago
1fb9b299d4
Add M524 to abort SD printing ( #12155 )
6 years ago
d26d9d5b81
Tweak IS_SD_INSERTED
6 years ago
c6a5c74208
Add parentheses to SD macros
6 years ago
aa9202260d
Fix endstop when no interrupt ( #12158 )
6 years ago
8c02dd971b
Move disable_all_steppers to minkill
6 years ago
3847c08f7e
Disable heaters/steppers before message
6 years ago
71e19baf69
Fix kill => disable_all_heaters => print_job_timer.stop ( #12146 )
...
- Remove `print_job_timer.stop()` from `disable_all_heaters`
- Call `print_job_timer.stop()` for relevant `disable_all_heaters()`.
- Split up `kill()` for watchdog interrupt safety
6 years ago
4cc1c2627e
Update German language ( #12143 )
6 years ago
75a0d46edf
Fix compile warning re: LCD_INFO_SCREEN_STYLE
6 years ago
a81763c237
Pins E sanity check tweak
6 years ago
bc22641002
[2.0.x] Updated Italian Language ( #12148 )
6 years ago
eded90bf87
Updated Azteeg X5 Mini Wifi pins for onboard SD ( #12133 )
6 years ago
27a84fd021
Remove unused option in Anycubic Kossel config ( #12138 )
6 years ago
67a3c5a16a
Alternative info screen (Prusa-style) ( #12132 )
...
* Fix Z value display
* Add HAS_PRINT_PROGRESS
* Alternative Info Screen option
* Add LCD_INFO_SCREEN_STYLE to example configs
6 years ago
5b7dd553d3
Fix sd_mmc_spi_mem capacity; clean up USB code ( #12134 )
...
- Fix an error in the return value of `sd_mmc_spi_read_capacity` which was causing the host OS to read beyond the last sector in the card.
- Clean up the USB flashdrive code and add better debugging.
6 years ago
df768e7d8f
Followup to #12129
6 years ago
3c13c9e3e9
[LPC176x] Fix USEABLE_HARDWARE_PWM macro, cleanup multiple LED support ( #12129 )
6 years ago
a768df83cb
Remove stale variable ( #12136 )
6 years ago
c36773bffb
Update the Ender-4 example config ( #12131 )
...
- Enable filament change menu
- Enable bed-PID
- Enable s-curve acceleration
- Enable some menu items
- Update from Skorpi's new version
- Fix extruder steps, deactivate nozzle clean feature
6 years ago
9c71bff5e8
Update German language ( #12115 )
6 years ago
9deb23aa47
Add missing SerialUSB definition for STM32 HAL ( #12124 )
6 years ago
0519ef0802
Update pins for final RemRam v1.3 board ( #12125 )
6 years ago
3ec3872730
Single Z raise value for all tool-changing / parking ( #12090 )
...
* Universal tool-change Z lift
* Add TOOLCHANGE_ZRAISE to example configs
* Park/unpark changes to example configs
* Implement DEBUG_DXC_MODE
6 years ago
6bdbe3299e
Fix a comment
6 years ago
bc75eb2c64
Cleanup for HAL_spi_Due.cpp
6 years ago
d82bcdeea1
Make PULSE_STOP(E) conditional ( #12121 )
6 years ago
c90e26dfa6
fix normal extruder stepping ( #12118 )
6 years ago
96bbda5d48
remove confusing comment ( #12120 )
6 years ago
f98f4ac7ea
Fix and improve EXTENSIBLE_UI ( #12117 )
...
- Add methods to access print counter data
- Clean up some inconsistent method names
- Clear lcd status after filament change
- Implement `lcd_reset_status` so it works like UltraLCD
6 years ago
8bf596bd4c
RETRACT_ZLIFT => RETRACT_ZRAISE
6 years ago
056561df93
[2.0.x] Enhancements to FILAMENT_RUNOUT_SENSOR ( #12069 )
...
- Added FILAMENT_RUNOUT_DISTANCE_MM option
- Added FILAMENT_MOTION_SENSOR option
6 years ago
cce4931342
Clean up recent contribs
6 years ago
8b5e51c9aa
STM32F4xx modifications for HAL_STM32 ( #12080 )
6 years ago
bf0c809ff2
Update M165 comment
6 years ago
9ac9649183
Mixer - update descriptions ( #12108 )
6 years ago
9bf5d4331c
Clear up some compiler warnings
6 years ago
0139762a96
Fix a sanity check
6 years ago
2ecb124e42
Fix trailing whitespace
6 years ago
f56968ba0b
New Continuous Filament Mixer ( #12098 )
6 years ago
2d2cd628c6
Update German language ( #12094 )
6 years ago
84b59d58fb
Clean up whitespace
6 years ago
06e2afe8e0
[2.0.x] Reduce HOMING_FEEDRATE_XY for Ender 3 ( #12105 )
...
Homing on the Ender 3 with HOMING_FEEDRATE_XY set to 50*60 was shown (#12074 ) to cause the end-stop micro-switches to bottom out, causing the carriage for both X and Y axis to physically crash into the micro switch. Reducing the homing speed prevents the switches from bottoming out.
6 years ago
af939c158a
Option for G0 to have a separate feedrate ( #12089 )
6 years ago
e5b4bf22d4
Remove debug output from flash persistent store implementation
6 years ago
42fb7c14b0
Update the sdcard usb sharing config and apply to Re-ARM
6 years ago
254b68fe2c
servo update
6 years ago
870bfd08f5
usb and sdcard sharing improvements
...
* Add traceback after watchdog timeout
Add the cpability to perform a traceback following a watchdog timeout.
* Enhanced hardware SPI
Allow use of either SSP0 or SSP1.
Ensure that no data is left in I/O buffers after calls to enable sharing of SSP hardware.
* Make flash emulation of eeprom the default
Make use of flash for eeprom storage the default. This means that usage of eeprom will not cause USB drive mount/unmount operations.
* Allow sharing of SD card
SD card I/O operations from the USB stack take place in idle loop, rather than at interrupt time. Allowing sharing of the SPI bus.
New configuration options to allow usage of the SD card to be specified.
* Fix problem with hardware SPI pins
6 years ago
5ddf52d58e
[HAL][LPC176x] Pull out framework into separate repository
...
Framework and build platform now located at https://github.com/p3p/pio-framework-arduino-lpc176x and https://github.com/p3p/pio-nxplpc-arduino-lpc176x respectively
fix mkssbase leds
move hardware serial
remove hardware/software serial
Hardware Serial extraction
HardwareSerial ISRs
fix disabled serial2 causing Serial object to link
move usb devices out to framework
separate out adc/pwm peripheral function from hal.cpp
fix includes
remove unused pwm init
move adc
HAL header update
templated filtered adc
LPC1769 platform
6 years ago
213e94bce2
[2.0.x] Updated slovak translation ( #12059 )
6 years ago
a40458405a
Fix datasize error when FWRETRACT is disabled ( #12086 )
6 years ago
951b25163e
Extend M217 with configurable park/raise ( #12076 )
6 years ago
ea13a77dcb
Fixed Z-Probes NO/NC for Anycubic Kossel ( #12083 )
6 years ago
ab9d5eb38d
Add Bootscreen Animation ( #12077 )
6 years ago
26208a5c2f
Clean up some boot screens
6 years ago
9b6be0ae0f
Fix lite status screen SD %
6 years ago
af3bf6c956
Tweak config spacing
6 years ago
a44ef27897
Outdent singlenozzle toolchange code
6 years ago
d338e4d875
Fix singlenozzle toolchange cold extrusion test
6 years ago
25b980dddb
Remove erroneous Pin 12 definition
...
There is no switchable Power Supply. Don't put it on Pin 12.
(Pin 12 is actually FAN1)
6 years ago
ddaef1a60c
Clean trailing whitespace
6 years ago
1407afad73
Move SENSITIVE_PINS to its own file
6 years ago
45e738876a
Add stepper MS3 support
...
Co-Authored-By: TheLongAndOnly <thelongandonly@users.noreply.github.com>
6 years ago
d43d4e4219
Refactor PRINTER_EVENT_LEDS, apply to M303 ( #12038 )
...
Co-Authored-By: Giuliano Zaro <gmagician@users.noreply.github.com>
6 years ago
d8d76cd2ba
[2.0.x] Italian language update ( #12060 )
6 years ago
e8d2cf4fb5
EEPROM followup (tmc_stepper_current_t)
6 years ago
50cbca4c55
Hide some menu items when busy
6 years ago
3cb5517ddb
Make singlenozzle tool-change honor no_move ( #12056 )
...
...Set no move earlier so it applies
6 years ago
d332fcb8fa
Fix firmware-retract compile errors ( #12061 )
6 years ago
43940d59ed
Fix trailing spaces
6 years ago
b2c1cd7eda
Allow cold change of active extruder ( #12055 )
...
Followup to #11994
6 years ago
d556dc1865
Fix and improve EEPROM storage ( #12054 )
...
* Clean up Temperature PID
* Improve EEPROM read/write/validate
* Group `SINGLENOZZLE` saved settings
* Group planner saved settings
* Group filament change saved settings
* Group skew saved settings
* Group `FWRETRACT` saved settings
6 years ago
9b5c1a5e77
Fix EEPROM checksum bug
...
Addressing #12048
6 years ago
272d4a5167
Apply #pragma once
6 years ago
07d33849b0
Fix unused var warning, apply ENABLED
6 years ago
a3e8cb1e44
[2.0.x] Ender-4 small improvements in Configuration ( #11843 )
6 years ago
cf5284cdf2
Add SD Firmware Update capability ( #12043 )
...
Co-Authored-By: timoxd7 <timoxd7@users.noreply.github.com>
6 years ago
0bd54392b7
Use uint8_t in EEPROM code
6 years ago
ce82015d5f
Fix include in G80
6 years ago
cef1de89d0
Fixed incorrect axis index. ( #12051 )
6 years ago
d6d48e63fb
Allow #defined TYPE arg to ultralcd menu macros ( #12041 )
...
Previously, it was not possible for the TYPE argument to ultralcd menu macros to itself be a #defined value. This made it difficult to create variables to set many related menu items to a common precision that could be easily changed.
6 years ago
2ef7175b42
Update Ender-2 BED_MAXTEMP ( #12042 )
...
Also added details to the README to make sure the Ender-2 status is properly documented.
6 years ago
5f6aabccbe
Tweak M48 spacing
6 years ago
ec9aa4f468
[2.0.x] Miscellaneous fixes ( #12039 )
...
* Allow override of soft SPI pins in `pins_*.h`
* Add default case to avoid compiler warning.
* Additional pin definitions for Archim 2.
* Einsy Retro has same timings as Einsy Rambo.
6 years ago
906a24fa81
Extensible user interface API ( #11193 )
6 years ago
ee253991d4
Various fixups for single-nozzle filament swap ( #12036 )
6 years ago
8dbb305e8e
Fix "Missing separator" errors. ( #12035 )
...
- Makefiles require tabs (not spaces) before shell commands.
- Other indentation can either be space or tabs.
6 years ago
55e810d512
Fix G80 compilation
6 years ago
d5017e2788
Add status screen with 4 nozzles
6 years ago
7db0113b53
Improve E_AXIS_N macro
6 years ago
191df5e17d
Correct PWM_PIN behavior for STM32 HALs ( #12027 )
6 years ago
f2ecf8d510
Add option to control Solenoids under PARKING_EXTRUDER ( #12028 )
6 years ago
74cd6cb4fc
Single nozzle filament change ( #11994 )
6 years ago
bfcf570d68
Try ISR_ALIASOF for Endstop Interrupts
6 years ago
c0d9058e25
Shorten an Italian menu title ( #12034 )
...
…and change a multi-use "back" menu item.
6 years ago
dffb4c63dc
[2.0.x] TMC2660 followup ( #12029 )
...
* Don't react to s2g on TMC2660. False positives
* Init with sensorless probing as well
6 years ago
d6b0fbd771
Use uint8_t for all fan speeds ( #12032 )
6 years ago
cb7844c8d4
Save PROGMEM on serial prefixes ( #12033 )
...
With default config and `EEPROM_SETTINGS`, saves over 200 bytes of PROGMEM.
6 years ago
07db08e39d
Fix EXTRUDER_AUTO_FAN_SPEED comment
6 years ago
ca0e308105
Fix up some units comments
6 years ago
65b8f3821b
Suppress temperature.h compile warning
6 years ago
c447d75916
Add support for TMC2660 ( #11998 )
6 years ago
cf0b9eb37c
no need to use destination in do_pause_e_move
6 years ago
e8d677620c
Use NUM_SERVOS in EEPROM code
...
Fix #12015
6 years ago
0fcdfdeed6
Followup to #12017
6 years ago
acac2adfc8
Add support for MeCreator2 ( #12017 )
6 years ago
49823a4939
Fix broken jerk handling ( #12019 )
...
Fix #12004
6 years ago
52a37913c1
Extend and apply some corrections
6 years ago
77b9a41f1f
Add G-code extensions to example configs
6 years ago
e09c144674
Add CNC-like G-code options
6 years ago
33056046a3
STM32 non-generic PWM_PIN and USEABLE_HARDWARE_PWM ( #12016 )
6 years ago
d5141c4e03
Fix up leading/trailing whitespace
6 years ago
03fc4d31d0
Makefile support for 32-bit Archim board and new TMC library ( #11997 )
...
* Support new TMC library and 32-bit Archim board
- Added IS_MCU flag
- When IS_MCU flag is 1, AVR compiler will be used
- When IS_MCU flag is 0, ARM compiler will be used
- Added support for new TMC library
- Added support for a 32-bit Archim board, which could probably be used as a basis for other 32-bit boards.
6 years ago
65b36642f8
Fix Anycubic Kossel config
6 years ago
fc326b3dde
Add USB_FLASH_DRIVE_SUPPORT to examples
...
Co-Authored-By: marcio-ao <marcio@alephobjects.com>
6 years ago
2067619a26
Add USB_FLASH_DRIVE_SUPPORT
6 years ago
07fe8d28be
[2.0.x] Partial Italian revert ( #12008 )
...
- Use a comma for decimals just in one message has not been a good idea.
- Full comments translation
6 years ago
517b4f4cd4
Fix lightweight UI hotends display
6 years ago
72a750e0eb
[2.0.x] Update Italian language ( #11996 )
6 years ago
bb561baf9e
Tweak some config comments
6 years ago
fcf6d127fd
STM32 timer simplification ( #11995 )
...
Prescalers aren't calculated for the given target frequency.
Stepper timer should run at 2 Mhz and temperature timer at 72 Khz.
6 years ago
8daadd2c8c
Fix TMC_DEBUG undefined report_tmc_status ( #11993 )
6 years ago
c40ea1f0fd
Update EEPROM_VERSION
...
And set EEPROM_OFFSET to 0, since the historical 100 skipped bytes are never used.
6 years ago
1358bd9319
Make MAX_EXTRUDERS always 6
6 years ago
001f26b642
Template struct simplification for serial ( #11990 )
6 years ago
348004c34f
STM32F7 HAL using the official STM32 Arduino Core ( #11750 )
6 years ago
3e58b3a5d4
Followup to #11943
6 years ago
c3229e1b34
Migrate to a new TMC library ( #11943 )
6 years ago
2abf3d258d
Korean language translation support ( #11987 )
6 years ago
d6955f25b2
Expand serial support in DUE/AVR hals exploiting the templated MarlinSerial classes ( #11988 )
6 years ago
f6f2246f59
Templatized serial classes ( #11982 )
6 years ago
ee53f7d813
Revert header reorg.
6 years ago
d619ba2685
Tweak STM32F4 config
6 years ago
d777cef837
fixed minimum macro ( #11986 )
6 years ago
e3f7b69105
Add PROBING_STEPPERS_OFF ( #11984 )
...
Co-Authored-By: houseofbugs <houseofbugs@gmail.com>
6 years ago
0e5bcdf695
Make DISABLE_INACTIVE_EXTRUDER a simple switch
6 years ago
0dedb3e139
Reorganize some core headers ( #11983 )
6 years ago
ab4549d2bc
[2.0.x] Add simultaneous retraction for mixing extruder ( #11941 )
6 years ago
c75f5a376b
Tweak some comments
6 years ago
f4c625d3a1
Ensure MIN/MAX overrides
6 years ago
3019713402
Reorganize some enums
6 years ago
606a4362b3
Reduce STM32F4 compile warnings
6 years ago
b3154b2120
Apply MOVE_Z_WHEN_IDLE to example configurations
...
Co-Authored-By: dot-bob <gibben@gmail.com>
6 years ago
b0fd8f2d74
Add option to move Z on double-click when idle
6 years ago
389376c40e
Clean up softspi.h
6 years ago
e78bdd654d
Clean up BABYSTEP options
6 years ago
8ae113ff36
Show zprobe_zoffset when BABYSTEP_HOTEND_Z_OFFSET is disabled ( #11973 )
6 years ago
2e98437392
Clean up main menu ( #11972 )
6 years ago
6d862b2916
Home before level corners, if needed ( #11976 )
...
…and add a consistent homing screen for all LCD pre-homing.
6 years ago
11ac75edcb
Use PGM_P for PSTR pointers ( #11977 )
6 years ago
4d5566a6b7
Add filament runout sensor menu item ( #11971 )
6 years ago
8489673cea
Adjust some HAL formatting
6 years ago
fb8a07660a
Followup to minmax patch
...
Co-Authored-By: Palatis <palatis@gmail.com>
6 years ago
3c40933713
Remove trailing spaces, old comment
6 years ago
a3ec805c97
Anycubic Kossel Linear+: corrected DELTA_DIAGONAL_ROD ( #11964 )
6 years ago
b30ca652ae
Replace MIN# / MAX# with variadic MIN / MAX ( #11960 )
6 years ago
e10f730478
Tweak vector_3::apply_rotation
6 years ago
e2ab78d876
Fix SERIAL_PORT_2 sanity check
6 years ago
a644d8cb93
Avoid copies in vector and matrix ( #11959 )
6 years ago
693865a649
Fix some whitespace
6 years ago
9903305dda
Merge pull request #9582 from tcm0116/2.0.x-sensorless_probing
...
[2.0.x] Add TMC2130 sensorless probing
6 years ago
14df753086
Correction for block->mix_steps
...
Fix #11484
6 years ago
2ecfda80ac
Improve support for JTAG/SWD pins reuse ( #11963 )
...
STM32 can reuse JTAG and SWD pins separately. Add `DISABLE_DEBUG` option to disable both interfaces and retain `DISABLE_JTAG` to disable JTAG only.
6 years ago
bb47009656
Apply sensorless changes to example configs
6 years ago
3286325044
Add TMC2130 sensorless probing
6 years ago
7d5c336c56
Corrections for dylsexic TMC
6 years ago
d89d8fe852
Fix Busy State in temperature.cpp
...
Fix #11954
6 years ago
70e7a465d8
[2.0.x] Fix compile error ( #11951 )
...
Fix compile error intruduced with M109 modification
6 years ago
935b120949
Anycubic Kossel: probe closer to the edge ( #11950 )
6 years ago
1410e79e7f
Ensure M109 handles autotemp
6 years ago
e4389f7d23
Standard methods to wait for heating ( #11949 )
6 years ago
bdc9889d3a
Fix a sanity check
6 years ago
321f9140d1
Followup to #11904
6 years ago
23114aeb81
Fix garbled M119 output. Honor NUM_RUNOUT_SENSORS ( #11948 )
6 years ago
1667ed9d1c
Pause should use ECHOLNPGM
6 years ago
93839e2f73
Add option to enable/disable autoretract altogether ( #11904 )
6 years ago
ad21a4f07b
Tweaks to HAL format and order
6 years ago
b682a1961a
Tweak STM32F7 TMC2660 class
6 years ago
a0a3b23e35
Reduce Raptor bootscreen by 144 bytes
6 years ago
95d793456b
Add Formbot Raptor config, fix other Formbot configs ( #11926 )
6 years ago
d016b572e3
[2.0.x] Add pin configuration for Fysetc F6 ( #11932 )
6 years ago
84926b1d5a
HAL general support for DISABLE_JTAG option ( #11211 )
...
Some STM32-based boards may use multiplexed JTAG pins as IO. Up to now the `DISABLE_JTAG` option (defined in pins files) was only supported for AT90-based boards. This commit generalizes the code and adds support for boards based on STM32F1 and STM32F4.
6 years ago
c575c5d5f6
Bring example configs up to date ( #11939 )
6 years ago
6b1a4f30a8
Fix case of T-Rex 3 _Statusscreen.h
6 years ago
ab7bfa86e2
Fix case of T-Rex-3 _Statusscreen.h
6 years ago
241168926d
Update some configs
6 years ago
cb6454118c
Workaround for Pronterface M29
6 years ago
eeab4141db
[2.0.x] Anycubic Trigorilla 14 pins tweak ( #11869 )
6 years ago
cb9dc56630
Add GT2560 v3 support ( #11914 )
6 years ago
f2e630a05e
Stow probe on probing failed ( #11936 )
...
Prevents probe from being left down should probing fail and print job continue
6 years ago
0b602ae101
[2.0.x] Fix Anycubic Kossel with Probe V1, stuck LCD message after stow ( #11929 )
6 years ago
dc11131656
[2.0.x] fix possible race condition ( #11923 )
...
Fix some commits done in #11900
6 years ago
d6b9327c11
Followup for Endstop Noise Threshold
...
Followup to #11912
6 years ago
aa6e8e9325
Tweak some config comments
6 years ago
5490a664f5
Expose: Homing Validation and Endstop Noise Threshold ( #11912 )
6 years ago
cee34f7290
Followup for BABYSTEP_HOTEND_Z_OFFSET ( #11916 )
6 years ago
884ad75cb8
Update config files
6 years ago
18e456d38d
[2.0.x] fix home endstop bug (DON'T MERGE, needs discussion) ( #11900 )
6 years ago
6742026568
Followup for 6 extruders
6 years ago
04bdff4115
Add a blank line
6 years ago
ccbd045f02
Fixed warning about comparing signed to unsigned ( #11909 )
6 years ago
1104054d73
2.0 IDEX Independent z offset and other fixes ( #11862 )
...
* Add Formbot Raptor board
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>
* Add a second Z probe Z offset
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>
* Modify method to utilize live adjustment of hotend z offset
Should probably move config option to babystepping and rename as it may now apply to all multiextruder systems
* Move config item and catchup other code to current method
6 years ago
217e0efd20
General option PAUSE_BEFORE_DEPLOY_STOW ( #11905 )
6 years ago
849dea92a8
Move probe extras below probe types
6 years ago
a2b0260f0f
Update Sublime files
6 years ago
a4cdffdd69
Support for manually deployed fixed probes ( #11899 )
6 years ago
ddcbf80f23
Followup for Z_TRIPLE_ENDSTOPS
6 years ago
c411e7eb0d
[2.0.x] Squelch compiler warnings seen with -Wall ( #11889 )
6 years ago
83105590a0
Better default values for Mesh Inset
6 years ago
4163c1a514
Fix end stop and Z-probe reporting logic
6 years ago
ea9eb2fc8f
Fix servo angles in config-store
6 years ago
d3d6be8210
Add MAX7219 reverse units option ( #11860 )
6 years ago
beab9733f8
Remove extra clauses in config-store
6 years ago
5a74b12b45
Followup to #11769
6 years ago
f38570ac55
Add custom user menu title ( #11769 )
6 years ago
17494099a9
Fix parking_extruder_tool_change
...
Fix #11872
6 years ago
140caf99b8
E0_CS_PIN moved from A13 to A15 on RAMPS-FD v2.2 ( #11865 )
6 years ago
10590c2f80
Fix some fan conditionals
6 years ago
e4ee607fc8
Fix Dual X FRS in M600
...
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>
6 years ago
bae8f82ba8
[2.0] Fix Mixing Extruder mixing factors ( #11861 )
6 years ago
c5e5cc5e9f
Fix some trailing whitespace, macros
6 years ago
54bd124665
2.0.x: Fix normalize_mix() ( #11856 )
...
Mix factors needed to be updated consistent with the recent Stepper/Planner code refactor.
6 years ago
5fbfbde532
Fix example file to pull in correct pins file
6 years ago
378f354939
IDEX Scaled Duplication is still under development
...
Take it out of the menu until it is tested and working.
6 years ago
65045ba54b
tmc_util fix part 2
...
Followup to 115abf9
6 years ago
09a2bee8aa
Support more filament runout sensors in M119 ( #11851 )
6 years ago
115abf9c53
Fix syntax error in front of `tmc_axes`
6 years ago
0780913848
IDEX Improvements ( #11848 )
6 years ago
39732838b4
Tweak indent of Chinese languages
6 years ago
53bd0b55cb
Followup for 6 extruders
6 years ago
1718eff54a
Code changes supporting up to 6 extruders
6 years ago
f5c210d33d
Config changes supporting up to 6 extruders
6 years ago
d948c6e867
RADDS Extension Board V3 support
6 years ago
c437bb08f1
Overhaul of the planner ( #11578 )
...
- Move FWRETRACT to the planner
- Combine leveling, skew, etc. in a single modifier method
- Have kinematic and non-kinematic moves call one planner method
6 years ago
8323a08642
Clean up some whitespace
6 years ago
6286afd456
Add Triple-Z options to example configs
6 years ago
1a6f2b29b8
Add support for Triple-Z steppers/endstops
6 years ago
bc06406d7d
Fix Anycubic Kossel config (probe crash) ( #11832 )
6 years ago
66f83d33e6
Fix some config comments
6 years ago
84ed9b5a63
Send "G33 S P1" for Delta Height Calibration ( #11831 )
6 years ago
215eee4fe5
Use 'friend' to access set_directions
6 years ago
ff51e7322d
Fix for Stepper::set_directions() compilation error ( #11838 )
6 years ago
809b232fa2
Fix stepper directions after M501/M502
...
See https://github.com/MarlinFirmware/Marlin/issues/11103#issuecomment-421387611
Co-Authored-By: tcm0116 <tcm0116@users.noreply.github.com>
6 years ago
f79a5a9dee
Tweak spacing of L6470 options
6 years ago
c37d3ae97d
[2.0.x] Fix NOZZLE_PARK_FEATURE for Anycubic Kossel ( #11812 )
6 years ago
4fb2134f00
Fix non-sensical values for Zonestar themistor table ( #11817 )
...
Values taken from Zonestar firmware for P802QA with a Melzi board. Timestamps from the firmware package are from April 2016.
6 years ago
b220a825a7
Fix raw_filwidth_value error
6 years ago
1933d5d6fb
Fix SD autostart with no LCD
6 years ago
8bce5370c7
Updated slovak translation ( #11807 )
6 years ago
64d629ba2a
[2.0.x] Italian language fix ( #11796 )
6 years ago
8584d3697d
Fix servo count define conflict
...
`MAX_SERVOS` => `NUM_SERVO_PLUGS`
6 years ago
06949ae510
Fix MSG_FILAMENT_CHANGE_HEAT_1 for small LCD
6 years ago
d882717d98
Save some PROGMEM with constexpr ( #11798 )
...
When possible, make `active_extruder` a `constexpr` to save some PROGMEM.
6 years ago
4f883d5971
[2.0.x] Extruder-Distinct Linear Advance K Factors ( #11789 )
6 years ago
fe9f088d60
[2.0.x] Anycubic LinearPlus, Trigorilla 1.4 ( #11730 )
6 years ago
b6aae2b322
Tweak RAMPS_FD_V1 pins
6 years ago
7391e23332
Fix RigidBoard FAN_PIN collision
6 years ago
53b8c3bd66
Add EXTERNAL_CLOSED_LOOP_CONTROLLER to examples
6 years ago
1b6bc19427
Add external closed loop controller support
6 years ago
2ebfe90be9
Add custom preheat temp to filament change ( #11475 )
6 years ago
69d0ed5791
[2.0.x] Fix ambiguous function call (SERIAL_PROTOCOL_F) when using Arduino_Core_STM32 ( #11747 )
6 years ago
d32c4efc77
Fix some trailing whitespace
6 years ago
bc1ba998b2
[2.0.x] Fix undefined symbol 'g29_in_progress' ( #11781 )
6 years ago
bad225dc04
Fix mesh leveling compile errors ( #11768 )
6 years ago
d783400330
Updates to STM32F7 HAL, for completeness ( #11770 )
6 years ago
72af8e0f02
Patch extruder_advance_K edit menu
...
Fix #11776
6 years ago
7e8c073fba
Fix extruder stops extruding with LA ( #11758 )
6 years ago
0c01099f17
hop_amount => current_hop
6 years ago
eafd62308e
Use TMC2208Stepper v0.2.5 ( #11714 )
6 years ago
e25d2ae4a2
[2.0.x] SWITCHING_TOOLHEAD ( #11623 )
6 years ago
f417408df1
[STM32F1] Fix HAL for new PlatformIO ( #11749 )
6 years ago
3d7f2c1fde
Fix directory name to be consistent ( #11745 )
6 years ago
a9c98a0e47
Create _Bootscreen.h
6 years ago
9f85d3a9cb
Create _statusscreen.h
6 years ago
e2e7b1d705
Break out support of the T-Rex 3
6 years ago
67996c2b66
Break out support for the T-Rex 3
6 years ago
9c8d9d282f
Break out support for Formbot T-Rex3 from previous versions
6 years ago
e3aac59637
Create pins_FORMBOT_TREX3.h
6 years ago
f580247581
Create pins_FORMBOT_TREX2.h
6 years ago
073857646b
seperate the T-Rex2 and T-Rex3 support
6 years ago
fe4fc2883b
Add support for Formbot T-Rex3
6 years ago
2a61c9a939
Various fixups to configs, spacing, etc.
6 years ago
b3efbc6e6e
Add MANUAL_E_MOVES_RELATIVE to more configs
6 years ago
679e4602fe
Add MANUAL_E_MOVES_RELATIVE to examples
6 years ago
beb51c2d58
Show manual extrusion moves as relative in LCD
...
- Implements FR#11724
- Old behavior can be restored by commenting out MANUAL_E_MOVES_RELATIVE
6 years ago
d10f29ae2e
Pass segment length in G2-G3
6 years ago
dcfde2317f
Pass segment length in prepare_kinematic_move_to ( #11737 )
6 years ago
d5379ee9d6
Fix search for white space in enqueued commands
6 years ago
8d5bea073b
Assume one Max7219 unit if not specified
6 years ago
9651ceb36b
Correct spelling of #endif
6 years ago
b213a89ef5
Sanity-check NOZZLE_PARK_POINT
6 years ago
86ee74731e
Comment for RADDS + RRDFGSC
6 years ago
ae1271b2ae
RADDS: Update Full Graphic Display Pins ( #11731 )
6 years ago
650d4313c4
Bring some configs up to date
6 years ago
530a13ab6c
[2.0.x] SECURITYFIX missing max temp error when PID is used ( #11717 )
6 years ago
12fded46c2
Correct some FR strings
...
Co-Authored-By: pipersw <pipersw@users.noreply.github.com>
6 years ago
aefc2f7cf9
Add Anet A2 and A2 Plus Configurations ( #11677 )
6 years ago
72fdb6bab3
Fix SWITCHING_NOZZLE zdiff ( #11683 )
6 years ago
8b837dc3ad
No need for last \n in G-code items
6 years ago
d1ceaf5550
[2.0.x] Followup to IDEX changes ( #11707 )
6 years ago
d62f4df0b7
Disable LCD Pins used by new Max7219 hook up if in that mode
6 years ago
fa772c31bf
Provide more options for Max7219 connection on Formbot
6 years ago
8e18e48d49
Merge pull request #11610 from Freeviv/bugfix-2.0.x
...
[2.0.x] Editable servo angles
6 years ago
59e76e5fdf
[2.0.x] Fix planner computation ( #11708 )
...
Fix #11697
6 years ago
509ee44611
Boot and status file should not have been added to main directory!
6 years ago
f8abe12a9c
Boot and status file should not have been added to main directory!
6 years ago
7680b64aa6
IDEX clean up ( #11690 )
6 years ago
49e107cea9
Restrict SW serial to AVR ( #11696 )
6 years ago
18f1af2dca
Fix up Teensy tests, servo sanity
6 years ago
74a04aed55
Fix compile error with NO_LCD_MENUS
6 years ago
509e1cf2bd
Add *_DRIVER_TYPE to remaining configs
6 years ago
d55f44edba
Printcounter improvements ( #11689 )
6 years ago
6a3207391f
Remove obsolete HAL_timer_restrain
6 years ago
e3fc9aa35f
Update some config comments
6 years ago
136860e8bb
Sanity-check SERVO pin for servo probes
6 years ago
66de50f5f8
Updated slovak translation ( #11684 )
6 years ago
ada85d5585
Improve HOTEND OFFSET Z display precision to 3 ( #11686 )
6 years ago
607c1e58d9
Improve HOTEND OFFSET Z display precision to 3 ( #11685 )
6 years ago
3e81745e81
Fix issues, make optional
6 years ago
aa80e448e2
Store servo angles in EEPROM
6 years ago
9953213513
Add EDITABLE_SERVO_ANGLES to example configs
6 years ago
0966bdcbc4
Reorganized ultralcd menu (10317) ( #10360 )
...
Replaced "Prepare" and "Control" menus with "Movement", "Temperature", "Configuration" and "Advanced Settings"
6 years ago
e40a3eef04
Support for Anet A2 Plus
6 years ago
32e38fee74
Update Controller Fan for Y2,Z2
6 years ago
59cf217e77
Fix 5 mixing steppers
6 years ago
2a2e8c314e
Suppress emergency parser G-code errors
...
Co-Authored-By: srieche <srieche@users.noreply.github.com>
6 years ago
7ecb8b4af5
[2.0.x] Teensy 3.1 and 3.2 support ( #11460 )
6 years ago
409a0632af
[2.0.x] Add Morpheus Board support ( #11651 )
6 years ago
0f14977b5d
LIGHTWEIGHT_UI: Allow feedrate % to exceed 255% ( #11656 )
...
- Changed type of integer used for feedrate percentage from uint8_t to uint16_t.
6 years ago
6dc9553aa5
Fix SWITCHING_NOZZLE compile error ( #11657 )
6 years ago
a15e570d3b
Fix SD progress with Lite Status Screen
...
Co-Authored-By: Lê Hoàng <icy.lord.love.angel@gmail.com>
6 years ago
66966dbd69
Tweak comments for newer multiplexer
6 years ago
933d833ec8
Tweak some Anet A6 comments
6 years ago
d1c9517903
Followup to hotend_offset[Z] patch
6 years ago
e2b8fc4f17
Reduce some debug strings
6 years ago
b71c2b8651
[2.0.x] Update LPC176x tests, fix clean script ( #11617 )
6 years ago
a317bb4991
Remove stray tab
6 years ago
acf5ae3083
!ENABLED => DISABLED
6 years ago
ba1919c1eb
HAL tweaks to LPC1768 main
6 years ago
0987ed2a18
Use American English
6 years ago
6483285bc5
HOTEND_OFFSET_Z always available ( #11603 )
6 years ago
f8c52c9c29
Azteeg X5 Mini WiFi support ( #11601 )
6 years ago
3671c63cde
Einsy Full Graphic LCD Fix ( #11604 )
...
Fixed issue with LCD timings for Einsy RAMBo board.
6 years ago
593d5375ea
Fix G28 resetting DUAL_NOZZLE_DUPLICATION_MODE ( #11605 )
...
There's no reason for G28 to reset DUAL_NOZZLE_DUPLICATION_MODE, because it only affects the E stepper, unlike DUAL_X_CARRIAGE which affects the X steppers as well.
6 years ago
f0dbe61692
Tweaks to motion.h reachable tests
6 years ago
2d3317a35b
Prettify Dual X Carriage description
6 years ago
cd9868f442
Make position_is_reachable() smarter about IDEX machines`
...
On many IDEX machines the allowed travel of the X1 carraige and X2 carraige does not perfectly overlap.
This helps the issue. But more work needs to be done at the higher level. (For example the X1_MAX_POS should probably be factored into G26's mesh validation pattern.)
6 years ago
97f6396b25
Fix RE_ARM LCD pins to avoid #undef
6 years ago
0e25f66c09
Fix Ultimaker servo pin
...
As pointed out at https://github.com/MarlinFirmware/Marlin/issues/7981#issuecomment-407116642
6 years ago
ad12b9b46b
Fix indentation, whitespace, spelling, formbot pins...
6 years ago
b5537dde7f
need to add E2END to pins_RAMPS_FD_V2.h ( #11564 )
6 years ago
8f0bbdcc9b
Fix up Max7219 orientations ( #11596 )
6 years ago
a77f8c6dd5
Implement servo support for STM32F1 ( #11580 )
...
Implement servo support for STM32F1. Original code was incomplete and depended on Servo library from stm32duino which conflicts with `module/servo.h`.
6 years ago
0456caf0ad
Consolidate shared HALs and isolate HAL compile ( #11552 )
6 years ago
dfe18ac633
Fix compilation error for STM32F1 with U8GLIB_SSD1306 or U8GLIB_SH1106 enabled ( #11583 )
...
The `binary.h` file required by `lcd/dogm/dogm_bitmaps.h` is not present in stm32duino environment. Binary macros are defined in `bit_constants.h` in stm32duino framework.
6 years ago
b0a8ce59bd
Update Boards.h to include Formbot support
6 years ago
62ce937540
Update pins.h to include the Formbot board
6 years ago
a82be36d5d
Create pins_FORMBOT.h
6 years ago
00d24a8219
Don't call __delay_4cycles for 0 cycle delay - takes a really long time. ( #11586 )
6 years ago
56f1e17a25
[2.0.x] Max7219 cleanup, simplify, and extend ( #11575 )
6 years ago
0b2d686160
Fix "SD init fail" problem for STM32F1 ( #11579 )
...
Fix "SD init fail" problem for STM32F1 caused by incorrect SS pin state and incorrect SPI mode. Issue #11225
6 years ago
a98f21ec5e
Marlin assumes signed chars
6 years ago
db30650731
Fix UBL/Homing ( #11566 )
6 years ago
aae4c67e5d
Max7219 Clean Up ( #11563 )
...
Some of the Rotations did not do the right thing with setting and clearing pixels.
I think it is correct now. But if not... It is much closer to being correct.
6 years ago
9de730b2bf
Update tool_change.cpp ( #11559 )
6 years ago
c2553f9888
2.0.x - Idex match119 ( #11556 )
...
* Update ubl_G29.cpp
* Update ultralcd.cpp
6 years ago
e9de321ac0
declare void Max7219_register_setup();
6 years ago
952a1bc9d5
Merge pull request #11551 from thinkyhead/bf2_trinamic_fixes
...
[2.0.x] Fix TMC2208 SW serial communication
6 years ago
67613bf5bd
Update Czech translations ( #11510 )
6 years ago
bd6d032628
Update default driver configuration
...
Co-Authored-By: teemuatlut <teemu.mantykallio@live.fi>
6 years ago
1561e61df7
New TMC2208 constructor
...
Co-Authored-By: teemuatlut <teemu.mantykallio@live.fi>
6 years ago
b37bfeffeb
[2.0.x] Use the new const functions of the persistentStore api ( #11544 )
6 years ago
5573ef62c6
[2.0.x] PersistentStore update followup ( #11549 )
6 years ago
846bd24eb9
MALYAN_LCD is ok without SD
6 years ago
834ea7fcea
Remove 'const' from PersistentStore::capacity
6 years ago
c64199941e
Compile only selected PIO environment ( #11519 )
6 years ago
5be2559eda
Use flash memory to emulate EEPROM ( #11500 )
...
Use a sector of the LPC flash memory to emulate EEPROM storage, removing the need to have an SD card to store system parameters.
6 years ago
6964e1a95a
Clean up trailing whitespace
6 years ago
865ee5985f
Followup persistent store with heading, const
6 years ago
a4b0148365
Easier to find 'static inline'
6 years ago
cc0a60453f
Merge pull request #11526 from hasenbanck/eeprom-cleanup
...
[2.0.x] Change direct eeprom access to HAL::PersistentStore
6 years ago
65c5227c29
Change M7219 I to setup Max7219 registers, but not do initialization pattern
6 years ago
577aeb4aa9
All EEPROM access uses persistentStore
6 years ago
6a8b906318
Followup for persistent_store_api.h
6 years ago
66d2b48b59
Update PersistentStore api ( #11538 )
...
- Clean up the API to use a `static` class instance to adhere to Marlin convention
- Add `const` position data access for read/write
- Add Storage capacity to the interface
6 years ago
60f1376798
Make M7219 I more robust and nice to look at
...
Make M2719 initialize the Max7219 registers and then run the initialization pattern (if one is specified).
6 years ago
fd15b1495a
add I parameter to M42 to allow access to sensitive pins
6 years ago
11b411a872
Improve AXIS_DRIVER_TYPE macros
6 years ago
f1347f783d
Optimize thermistor table 71
...
agData in Table 71 is extremely oversampled (see Issue #11220 ). I have removed the data points that perform *worse* than linearly interpolating the remaining points, and fixed up two points that were simply rounded incorrectly.
Co-Authored-By: Aaron Griffith <aargri@gmail.com>
6 years ago
0bda22367b
Allow Einsy RAMBo FAN1_PIN override
6 years ago
1b921b246b
Fix pca9632_set_led_color
...
…when used with an I2C screen.
Co-Authored-By: soimy <soimy@163.com>
6 years ago
aa9d329560
Reduce max accel in Creality configs
6 years ago
c93538e9f3
UBL/planner patch tweaks
6 years ago
0af22549a6
Allow G33 to compile with no LCD
6 years ago
fc55f1da01
Account for UBL correction when setting the planner position ( #11486 )
6 years ago
b328fb4dc9
Treat TMC2660 like non-TMC ( #11508 )
6 years ago
72b086b90d
Add A5984 to example configurations
6 years ago
a1a5367380
Smoothieboard V1.0/1.1 and A5984 support
6 years ago
f891416e70
No raise on G28 after power-loss
6 years ago
e4ecade8d4
Fix AUTO_POWER_CONTROL compile error
...
Counterpart to #11467
Co-Authored-By: lsellens <lsellens@users.noreply.github.com>
6 years ago
eee1b7c50c
[2.0.x] Fix compile error ( #11465 )
...
Address #11463
6 years ago
e85feb2545
[2.0.x] Better timing handling ( #11461 )
6 years ago
79835590e3
Easier to disable homing validation ( #11458 )
6 years ago
131d216afa
Fix drivers.h dependency, defer macro evaluation ( #11450 )
6 years ago
9c62c47579
[2.0.x] Fix Dual X Carriage tool change crash ( #11447 )
6 years ago
9bae413901
Add Bigtreetech/BIQU KFB 2.0 board ( #11446 )
6 years ago
f2224755ad
Fix jumping progress bar. ( #11439 )
...
- When LCD_SET_PROGRESS_MANUALLY was disabled and an SD print was not active (i.e. the printer was idle), progress_bar_percent would read uninitialized memory from stack and cause progress bar to jump wildly.
- Also updated conditions in `#ifdef` to match `ultralcd.cpp`
6 years ago
aae02827c0
Cosmetic pins changes
6 years ago
64c493ad82
MKS_12864_OLED code cleanup
7 years ago
b826bf4194
Fix initial safe_speed in jerk code ( #11417 )
7 years ago
2cc950d67e
[2.0.x] MKS SBASE Trinamic examples/support ( #11402 )
7 years ago
16432376ab
Revert "[2.0.x]Idex and bl touch fixes" ( #11407 )
...
* Revert "[2.0.x] bltouch home refinements (#11397 )"
This reverts commit 74900f7a70#11395 )"
This reverts commit 6dafb90c01
7 years ago
74900f7a70
[2.0.x] bltouch home refinements ( #11397 )
...
Just create a better functions call logic flow
7 years ago
6dafb90c01
[2.0.x]Idex and bl touch fixes ( #11395 )
...
* Fix BLTouch homing
Deploy at start, dont call generic stow function at finish or raise goes too high before setting 0
* Update tool_change.cpp
* Update motion.cpp
* Update motion.cpp
* Update motion.cpp
* Update motion.cpp
* Change brackets to be more in align of Marlin coding standards
7 years ago
5ce5ff8e9b
[2.0.x] fix bltouch homing ( #11379 )
...
Partially revert. Seems to solve the issue, but one report says G29 still fails.
7 years ago
15d68cb496
Pre-override of ST7920 delays before HAL.h
7 years ago
8a24ff94d1
AT90USB1286 PIO cleanup and optimization ( #11230 )
...
-normalize `env` and `board` to lowercase naming convention.
-make board `name` follow descriptive convention.
-implement `-fsingle-precision-constant` compile optimization per https://github.com/MarlinFirmware/Marlin/pull/11178#issuecomment-401673901
-fix typo in 5DPRINT entry.
7 years ago
094e6d81a5
Add Einstart-S support ( #11219 )
...
Indeed the HAL does not need to be mucked around with to expose ATmega2560 pins not available as numbers on the MEGA board, I'll need to update the wiki with that tidbit and a reference to the pin-mapping comment in `fastio_1280.h`.
7 years ago
244b9a8257
Better fastio 1280/2560 pin list
...
Co-Authored-By: bleughb <36889022+bleughb@users.noreply.github.com>
7 years ago
955a7f0ae9
Improve driver.h macros ( #11371 )
7 years ago
aadcf08913
[2.0.x] add Calibrate Z (M915) to Prepare Menu ( #11331 )
7 years ago
4237c3d9f8
[2.0.x] different bltouch init ( #11135 )
7 years ago
624986d423
Ensure ADC conversion is complete before reading ( #11336 )
...
The current Marlin implementation relies on a timer interrupt to start the ADC conversion and read it. However in some circumstances the interrupt can be delayed resulting in insufficient time being available for the ADC conversion. This results in a bad reading and false temperature fluctuations. These changes make sure that the conversion is complete (by checking the ADC hardware via the HAL) before reading a value.
See: https://github.com/MarlinFirmware/Marlin/issues/11323
7 years ago
e2aa635e70
Fix Anet A6 thermistors
...
Co-Authored-By: vitekn <vitekn@users.noreply.github.com>
7 years ago
67b205fd45
Add support for board RuRAMPS4D v1.3 ( #11363 )
7 years ago
d1c6687ecd
Update MKS sBase pins ( #11357 )
7 years ago
048dbf6eca
Merge pull request #11275 from thinkyhead/bf2_pwm_adjustments
...
[2.0.x] Tweak some SoftPWM code
7 years ago
e05e95cf97
Clean trailing whitespace
7 years ago
22ebbc091f
Tweak some SoftPWM code
7 years ago
32de09f5c5
Specify some extra CR-10S pins
7 years ago
9c2bfa2ab3
Remove extra parameter to enqueue. ( #11364 )
7 years ago
bd3ec66a78
[2.0.x] typo fix ( #11365 )
...
Typo fix
7 years ago
fbcdf5eaeb
Simplify stepper driver per-axis selection
7 years ago
e5c0b490c8
Add *_DRIVER_TYPE to example configs
...
Co-Authored-By: teemuatlut <teemu.mantykallio@live.fi>
7 years ago
fbdbe53290
Fix get_period_inverse(0) so it doesn't crash ( #11334 )
7 years ago
14e2b11195
Fix spelling in configs
7 years ago
4685c7d59f
Followup to M91x I patch
7 years ago
62fa028155
Handle dual gantry machines better
7 years ago
09485f63e9
add missing ')'
7 years ago
a35abce1ac
Fix missing ')'
7 years ago
76d4cfb064
Tweak some Max7219 code
7 years ago
4195757585
Merge pull request #11309 from thinkyhead/bf2_manual_probe_start_z
...
[2.0.x] Manual Z Start Height
7 years ago
03b01e2500
Folger Tech i3-2020 now defaults to 2 Max7219 units
7 years ago
db85ca93c4
Change Max7219_idle_task() to use a column instead of row if Y-Axis as 16 LED's
7 years ago
9660996cc3
Add Multi Unit Support for Max7219 to bugfix_2.0.0 ( #11285 )
...
* Add Multi Unit Support for Max7219 to bugfix_2.0.0
* Apply multi-MAX7219 to example configs
* Tweak some spacing, macros
7 years ago
39c8aed8ba
Add MANUAL_PROBE_START_Z to example configs
7 years ago
2106fa26b1
Add MANUAL_PROBE_START_Z for manual probing
7 years ago
17ed0f815c
Fix tool_change call in UBL G29
...
Fix #11279 , #11252
7 years ago
6d2aff03bd
Merge pull request #11306 from thinkyhead/bf2_power_loss_pin
...
[2.0.x] Add support for power loss detect pin
7 years ago
63a146d424
planner.synchronize at start of tool_change
...
See https://github.com/MarlinFirmware/Marlin/issues/10949#issuecomment-398540498
7 years ago
665ac1e4d0
Add POWER_LOSS_PIN support
7 years ago
2243f72523
Add POWER_LOSS_PIN to example configs
7 years ago
47d5fcbbcc
[2.0.x] Change MKS SBASE default serial port to avoid confusion ( #11301 )
7 years ago
c83109c0ae
Merge pull request #11238 from xC0000005/MalyanLCDUpdate
...
[2.0.x] Malyan LCD Feedrate + Better Temp Handling
7 years ago
64f007580b
Fix some header comments
7 years ago
aed1d17a2d
Initialize default units ( #11295 )
...
When `INCH_MODE_SUPPORT` is enabled no default unit is set. This fixes it.
7 years ago
8c40f0c6c7
Reduce TQ message code size
7 years ago
b04e0c0cbb
Malyan LCD feedrate, better temp handling.
7 years ago
065e9c3d66
Add card.longest_filename method
7 years ago
71df1f7f57
Don't display M421 information for UBL at startup
...
It takes too long to display the mesh data for large mesh's at startup. We should consider ways to speed this up.
Perhaps it makes sense to display an entire row of the mesh instead of just one mesh point?
7 years ago
be7d1dfb3c
Merge pull request #11267 from teemuatlut/bf2_lpc_spi
...
[2.0.x] LPC1768: Expand hardware SPI class
7 years ago
8f686aa449
[2.0.x] Fix change filament crash ( #11269 )
...
Prevent crash, on filament change, when printer is not homed
7 years ago
f38c81cdde
LPC176x: Expand HW SPI class
7 years ago
3b5dec4b13
Add new LPC include folder
7 years ago
e486326910
Vellemann K8400 Y bed size is 180
...
Co-Authored-By: kaimimue <kaimimue@users.noreply.github.com>
7 years ago
e5ea9d200f
[2.0.x] fix kill printer ( #11260 )
...
This will fix kill message on dual printer with 0 alignment offset
7 years ago
8c57cadbe7
Include stdlib in fontutils ( #11251 )
...
When `REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER` is defined and Re-ARM build is attempted, `u8g_fontutf8.cpp` includes `fontutils.h` which uses `abs()`.
However, `abs()` is defined in `stdlib.h` which is not included in `fontutils.h`, so compile fails with an error.
Include `stdlib.h` in `fontutils.h` so that `abs()` is defined before `u8g_fontutf8.cpp` needs to use it, resolving the compile error.
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
7 years ago
bf7d0ba859
Assert that XY probe offsets are integers
7 years ago
12854f1909
Add Z_CLEARANCE_MULTI_PROBE to example configs
...
Co-Authored-By: nightgryphon <ngryph@gmail.com>
7 years ago
25e2ca8896
Add Z_CLEARANCE_MULTI_PROBE
...
Co-Authored-By: nightgryphon <ngryph@gmail.com>
7 years ago
fd8a76493b
Unify M91x parameter I meaning, simplify reports ( #11249 )
7 years ago
566d05006d
report_state > event_handler
...
Make the endstop report method track endstop changes on its own.
7 years ago
6b521b6df2
Loosen thermistor table size limit
...
Co-Authored-By: Aaron Griffith <aargri@gmail.com>
7 years ago
20761b88e0
Merge pull request #11212 from AlexanderAmelkin/2.0-HD44780-remove-unused-include
...
[2.0.x][HD44780] Remove unused include
7 years ago
603e136e87
Resolve issue where user can't edit UBL's mesh
7 years ago
ed720194d2
[2.0.x][HD44780] Remove unused include
...
The <binary.h> header is not available in STM32 toolchain
and is not used anywhere in ultralcd_common_HD44780.h.
If it is used anywhere in HD44780 support for other platforms,
it must be included in the corresponding .cpp file directly
and put under appropriate conditional compilation directives
for the platform requiring it.
As I was unable to find such code, I consider the file unused
and hence remove the inclusion.
7 years ago
d05e832f29
Add STM32F1 support for SD-based EEPROM
7 years ago
63f4c9bdb9
Followup to float maths patch
7 years ago
2992112da0
Optimize delta kinematics
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
1367df2875
Replace double with float, optimize calculation
7 years ago
d960d448fa
Optimize calculations with LROUND
7 years ago
68e6650df7
Remove Quake Fast Inverse SQRT (it isn't faster)
7 years ago
e7e896e7d7
More tweaks to fastio_Due.h
7 years ago
55f4744e54
[LPC176x] Endstop Interrupts Feature ( #11202 )
...
Enable the endstop interrupts feature for LPC176x boards. Although Smoothieboard chose to use non-interrupt capable pins for their endstops, and this has been copied by clones, so they can't use it.
7 years ago
5abf5bc8a7
[LPC176x] Fix Interrupt forward declarations ( #11200 )
7 years ago
cbea385ed7
[2.0.x] Fix LCD_LANGUAGE options list formatting in config ( #11198 )
...
* Fix LCD_LANGUAGE options list formatting in config
* Remove 'cn' language option from list
7 years ago
6837252fba
Merge pull request #11196 from thinkyhead/bf2_fix_m914_sgt
...
[2.0.x] No M914 or SGT with non-sensorless axes
7 years ago
5379c115c8
Fix Trigorilla include typo
7 years ago
9c058091e9
No M914 or SGT set for non-sensorless axes
7 years ago
c7ec6c68e7
Patch SCARA config to match 1.1.x
7 years ago
480a3d3d0c
Apply sensorless homing requirements only for specified axes
7 years ago
47ee149dfd
Merge pull request #11195 from thinkyhead/bf2_tronxy_x3a
...
[2.0.x] Tronxy X3A configurations and thermistor
7 years ago
8c0ec81a19
Followup to #11187
7 years ago
48c1f32b3e
Add configurations for Tronxy X3A
7 years ago
568cfe7caa
Add thermistor 501 (100K Zonestar)
7 years ago
Jacob Jordan