c0b75f49b6
Fix "no effect" and "unused variable" compile warnings ( #12473 )
6 years ago
5a4fd8e0a6
Fix access to the DWT peripheral for STM32 HAL ( #12434 )
...
Access to the DWT peripheral for the `CYCCNT` register needs to happen before `main()`. The code needs to be called after the setup of the system clocks, so the right place is between the `premain()` and `main()` function of the STM32 Arduino core.
This patch moves the DWT access code to a new function, which is then placed between `premain()` and `main()`.
6 years ago
7f225b9421
Fix MAX_MESSAGE_LENGTH
6 years ago
06674a321a
Remove extra include
6 years ago
c1e17037e5
Various fixes for MarlinUI and ExtUI ( #12439 )
6 years ago
d3605cfc26
Don't start watching heaters when target is 0 ( #12453 )
6 years ago
93e958f695
Fix compile error with ZONESTAR_LCD+NO_LCD_MENUS ( #12466 )
6 years ago
22d7fed60a
Fix compile error with SD_FIRMWARE_UPDATE ( #12462 )
6 years ago
779b2709ec
Change temperature pin order for RemRam V1 ( #12458 )
...
Beta testers suggested to adopt the RAMPS order of temperature probe connectors. This commit fixes the order to the RAMPS order.
6 years ago
8ebb4dc294
Followup to static CardReader
6 years ago
7ee5894360
Allow float XY probe offsets
...
Responding to #12383
XY probe offsets should be integers because adding decimal points makes the code larger. But if decimals are very much wanted, this commit removes the old restriction.
6 years ago
43ecdb606f
Fix a compile warning ( #12452 )
6 years ago
984c4ba8c7
Enable SD Card on RepRap Display and RADDS ( #12446 )
...
* Enable SD Card on RepRap Display and RADDS
Define the necessary pins in `pins_RADDS.h` (copied from the `RADDS_DISPLAY` section) for the use of the SD card slot on RRD.
6 years ago
56a94c2a26
Use 'target_extruder' in M104 as with M109 ( #12448 )
6 years ago
66580f32c2
Make CardReader class static ( #12451 )
...
* Make CardReader a static class
* Make CardReader flags into bitfields
6 years ago
3e9ffaddb6
Consolidate, optimize some LCD menu code ( #12450 )
6 years ago
d97e31db4c
Optimize Power-Loss Recovery ( #12440 )
6 years ago
ca21ac6b9b
Support two MAX6675 thermocouples ( #8686 )
6 years ago
0e610815e4
No need for Cap:PAREN_COMMENTS
6 years ago
7a075a5dc9
Tweak extruder errors
6 years ago
2d92f333f5
Fix GcodeSuite::T active_extruder reference
6 years ago
d2bb53702a
Optimize target_extruder, ignore T with mixing ( #12432 )
...
* Optimize target_extruder, ignore T with mixing
* Give G-code Tn parity with tool_change
6 years ago
5e586a6b39
Fix to runout sensor code. ( #12431 )
...
- "old_state" is no longer a class static variable.
6 years ago
d82c350de7
Miscellaneous LCD code renaming, reordering ( #12430 )
...
* Move special characters to language.h
* Apply some naming standards
* Clean up menu item draw functions
* Rename some Temperature methods
* UI => ExtUI
6 years ago
edfd106bc5
Rejigger Filament Runout class ( #12428 )
6 years ago
f4c128ecaa
Move RRW keypad code to a common method ( #12429 )
6 years ago
54ec5528a0
hasstatus => has_status
6 years ago
ebf585b673
Fix an old sanity check
6 years ago
052d102ded
UltiMachine Archim 1 support ( #12404 )
6 years ago
664e20754d
Clean up pins files
6 years ago
1eb5249598
Fix Formbot Trex-2+ configs
...
Followup to #12422
6 years ago
075a22ed65
Update Portuguese-Brazilian translation ( #12402 )
6 years ago
3ceab8474c
Add required "cardreader.h" include ( #12419 )
6 years ago
98c2fc4e42
Endstops fix followup ( #12423 )
...
Followup to #12413
6 years ago
f19fd642ce
Updates to Formbot T-Rex 2+ configuration files ( #12422 )
...
Updates to Formbot T-Rex 2+ configuration files
6 years ago
cda5ef08fa
Debug of G2-G3 for UBL ( #12386 )
...
Changes only affect UBL. Everything else is left alone.
6 years ago
9ad3aed0ef
Fix tool-change for MIXING_EXTRUDER with < 2 virtual tools ( #12417 )
...
Fix #12416
Better handling of `ENABLED(MIXING_EXTRUDER) && !MIXING_VIRTUAL_TOOLS > 1` - to not fall through to the general case. Fix compiler warnings for `#elif EXTRUDERS < 2`.
6 years ago
d631267548
Refine endstops fixes ( #12413 )
...
When endstops/probe are enabled `ENDSTOP_NOISE_THRESHOLD` calls to `update` are required to properly re-sync endstops/probe status.
6 years ago
0ee1a92971
Group status methods, share reset_status with Extensible UI ( #12414 )
...
* Group status methods, share reset_status with Extensible UI
* Move common DOGM code to headers
6 years ago
690c4e8457
Clean TLM trailing whitespace
6 years ago
143b2896e0
Add M412 to enable/disable filament runout detection ( #12406 )
6 years ago
a163c89c6a
Followup to 50af1d1
6 years ago
be6271767f
Fix BABYSTEP_ZPROBE_OFFSET ( #12408 )
...
Fix #12399
Did not compile without `WATCH_HOTENDS || WATCH_THE_BED`.
Add condition to include "../../module/temperature.h".
6 years ago
50af1d1e08
Differentiate translated On/Off from Serial ON/OFF
6 years ago
df907a905f
Update UBL comments for debug change
6 years ago
da17f8ad37
For now (!) don't synchronize in M204 and M205
...
See if this has any deleterious effect on motion planning by slicers that inser their own jerk and acceleration controls. The problem I see is that these settings can take effect on blocks already in the planner, and the only way around this would be to shadow these settings in planner blocks and use the shadowed settings in the planner.
6 years ago
a3923424c7
Clean up LCD width/height determination
6 years ago
a0c795b097
Encapsulate common display code in a singleton ( #12395 )
...
* Encapsulate common LCD code in a singleton
* Depend more UBL code on UBL_DEVEL_DEBUGGING
- Since most users don't need the debugging on at all times, this helps reduce the default build size for UBL by over 2K, a little closer to fitting on 128K boards.
6 years ago
9da6809ac3
Adjust some comment spacing
6 years ago
471f403a67
Reduce code size with plain inlines
6 years ago
30a49f5ee2
Apply extra condition to LCD_PROGRESS_BAR
6 years ago
4e0c935959
Update HAL and libs formatting
6 years ago
47483e8c17
Update Raptor config
6 years ago
6093df11dc
Allow G26 to use the active extruder ( #12387 )
...
* Make lcd_quick_feedback argument optional
* Add click_to_cancel option to wait_for_hotend/bed
* Have G26 use the active nozzle and wait_for_hotend/bed
* Use wait_for_release in UBL G29
* Add 'T' parameter to G26 for an initial tool-change
6 years ago
4260282df7
Tevo Little Monster example configuration ( #12370 )
6 years ago
bed15fcd81
Tweak 'echo_not_entered' used by MBL's G29
6 years ago
c239131ff5
Use 'serial_spaces' in 'print_2d_array'
6 years ago
56150ec030
Add reference comments to MeshLevelingState
6 years ago
24c5e57bb6
Update German language ( #12379 )
6 years ago
fd7fd55662
Solve endstops issues ( #12382 )
...
- Partially reverts #11900 and tries to solve #12336
6 years ago
78ccedd6a8
Fix M91x sanity-check to permit TMC2660
...
Fix #12362
6 years ago
b60abc7c37
[2.0.x] Macro G-codes ( #9365 )
6 years ago
ccdbf20f60
Update Italian language ( #12368 )
6 years ago
d08847b1a6
Update Slovak translation ( #12376 )
6 years ago
7665dff58b
No error on T0 with single-extruder and fix MIXING_EXTRUDER virtual tools ( #12375 )
6 years ago
4ed6397e5d
More comprehensive NO_LCD_MENUS ( #12367 )
6 years ago
9c8f083d6c
Extend pins errors to include the processor
6 years ago
525ea554a1
Remove obsolete comments
6 years ago
ef724edd80
Apply HAS_LCD_MENU in EEPROM code
6 years ago
b169320a03
Clean trailing whitespace
6 years ago
81b1e9d272
Fix up xdiff, ydiff, zdiff in tool change
...
Followup to #12137
6 years ago
6471a75a22
Combine more tool-change variables ( #12137 )
6 years ago
147e270208
Restore GTM32_PRO_VB temp and heater pins
...
Undo #12345
6 years ago
8def25e475
Set CUSTOM_MACHINE_NAME for some configs
6 years ago
812f6a7dd7
Fix Resume from SD Pause
...
In reference to https://github.com/MarlinFirmware/Marlin/pull/12098#issuecomment-436231690
6 years ago
4f72e041f2
Use card.stopSDPrint() for completeness
6 years ago
488a17b3f5
Use IS_SD_PRINTING() more
6 years ago
4dbaa6369f
Fix const pointer assignment compile error ( #12350 )
6 years ago
959ed32636
Update Italian language ( #12352 )
6 years ago
812bfec65e
Update Slovak translation ( #12354 )
6 years ago
1624722566
Update German translation ( #12355 )
6 years ago
e574f01568
More advanced pause tweaks ( #12356 )
...
* Followup to LCD_TIMEOUT_TO_STATUS=0
* Make continuous purge screen fit 20x4
* Unify purge message modes
* Preserve last-set pause header mode
6 years ago
5a470d4a49
Apply some tool-change cleanup
6 years ago
34ea458667
Fixed advanced pause messages ( #12353 )
6 years ago
4c5ca89d8c
Show the appropriate pause message ( #12348 )
6 years ago
8517d5f915
LCD menu code refactoring and cleanup ( #12308 )
6 years ago
b3b4e6dc45
Change Marlin debug flag names to fix conflicts ( #12340 )
...
In reference to #11000
6 years ago
f7e682eeee
Update Italian language ( #12344 )
6 years ago
a813900fce
Add Geeetech Rostock 301 config, update GTM32 Pro VB pins ( #12345 )
6 years ago
04f173790f
Remove trailing whitespace
6 years ago
c536ee1122
Clean up bq Zum Mega 3D pins
6 years ago
c31e1735dd
Restore LPC1768_PIN_INTERRUPT_M, apply to Z3
...
- In reference to #12166
6 years ago
93d5b945dd
Hide mesh editing until a valid mesh exists
6 years ago
f34f09c821
Update German language ( #12336 )
6 years ago
eefd7676a3
Updated slovak translation ( #12338 )
6 years ago
486f2a66a9
Fix MBL XY parameter error messages
...
Fix #11522
6 years ago
2613ddf61c
Fix "circle"
6 years ago
b779b42ffd
Prevent current step-down going negative
...
Addressing #11348
6 years ago
427bc64ba1
G28 O respects HOME_AFTER_DEACTIVATE
...
Addressing #11271
6 years ago
3866aeac52
Clean up ENCODER_RATE_MULTIPLIER config
6 years ago
498dfa291e
Update and fix CHDK
6 years ago
fed84f2961
Use multiplier edit item for mesh point editing
6 years ago
d5ab4cd22a
Provide a default for Z_PROBE_LOW_POINT
6 years ago
3cbc3ecdd7
Fix 'M43 T' to use 'L' as last pin
...
- The documentation is correct. The code was wrong.
6 years ago
1769249876
Recommend keeping endstops off
6 years ago
5182eaf661
Fix endstops enable behavior during probing
...
Fix a bug introduced in #9582
6 years ago
07a0822ebe
M420 support in MARLIN_DEV_MODE
6 years ago
63be48ada6
Add MESH_EDIT_MENU to example configs
6 years ago
82ff7c6542
Add a mesh edit menu for MBL / ABL-Bilinear
6 years ago
44fa7fb18c
Cleanups for leveling-related code
6 years ago
cc2bc67440
ENABLED(NEWPANEL) => HAS_LCD_MENU
6 years ago
fc84878cba
MSG_UBL_EDIT_MESH_MENU => MSG_EDIT_MESH
6 years ago
cd066bfeba
Extend error messages for E factors sanity-checks
6 years ago
c10edb0998
Update, correct sanity-checks for up to 6 extruders ( #12333 )
6 years ago
0c85869c26
Clean up file endings
6 years ago
b99f0776d6
Clean up some U8G files
6 years ago
8014e1cc9d
Allow disable of LCD_TIMEOUT_TO_STATUS (when 0)
6 years ago
bd05816fd8
Update Italian language ( #12327 )
6 years ago
3c21483c88
Provide DOGLCD SPI pins for MKS SBASE + VIKI
6 years ago
e0956bb572
Drop 'register' storage specifier
6 years ago
c04cf127f7
Fix EEPROM servo angles init, section grouping
6 years ago
9c0e05552e
Suppress some compile warnings
6 years ago
176654791e
Use board-specific or platform SPI pins in HAL_STM32 ( #12323 )
6 years ago
60dbd8161c
Fix VMAX editing
...
Fix #12326
6 years ago
b7ca93ba37
Remove dead comment
6 years ago
608be966d7
Add servos to pins_FYSTEC_F6_13.h
6 years ago
67b22760d9
Return to status to show manual deploy/stow messages ( #12324 )
6 years ago
f5e8e8b53d
Fix broken LPC176x build ( #12317 )
...
* Fix broken LPC176x build
* Add UBL+HD44780 test for LPC1768
6 years ago
f5eab912ed
Apply #pragma once, misc cleanup ( #12322 )
...
* Apply #pragma once in headers
* Adjust some thermistors formatting
* Misc cleanup and formatting
6 years ago
8696f882a9
Merge pull request #12313 from thinkyhead/bf2_scara_home_offset
...
Revive SCARA home offset (not fully implemented)
6 years ago
56d2dcb184
Use first_page flag in place of page.page == 0
6 years ago
d1ff22b983
Revive SCARA's home offset (unimplemented)
6 years ago
2c9586be0c
Clear up HAS_WORKSPACE_OFFSET meaning
6 years ago
6e3caf23b6
IS_DELTA => ENABLED(DELTA)
6 years ago
19f49db96f
Tweak / reduce menu items
6 years ago
e4cf175163
Synchronize on M204, M205 ( #12302 )
...
* Add parser.seen for multiple parameters
* Fix M666, use !seen for report
* Synchronize on M204, M205
6 years ago
5ba6607181
Fix keypad-related compile error ( #12306 )
6 years ago
2fb2e286ee
Followup to #12256
6 years ago
3eb9838dca
Simplify TMC sanity-checks
6 years ago
f5b31e218d
Followup to #12082
6 years ago
31c28d0dd2
Drop pgm_read_*_near and let headers choose ( #12301 )
...
- Drop `pgm_read_*_near` and let headers choose.
- Define `USE_EXECUTE_COMMANDS_IMMEDIATE` as a conditional.
- Add `process_subcommands_now` for SRAM-based commands.
6 years ago
fce150f094
inline static => static inline
6 years ago
323c088356
Restore LED light color after pid tuning ( #12082 )
6 years ago
9f77df2590
Followup to menu refactor. TMC warnings, sanity. ( #12288 )
...
- Followup fixes for menu refactor
- Fix TMC sanity checks, unused var warnings
6 years ago
cafabf2055
Implement DELAY_NS with CYCCNT on Cortex-M7 ( #12283 )
6 years ago
f5498168ae
Ensure PENDING/ELAPSED use a 32-bit integer
6 years ago
6e041b9c61
Use blink to show more info on LCD ( #12256 )
6 years ago
eb5600acd2
Add parentheses to LCD_CLICKED
6 years ago
42f8b6c530
Make M125 work with SDSUPPORT ( #12289 )
6 years ago
f319087372
Followup to #12293
6 years ago
74bbb13008
Fix Mixer calculations for 32-bit processors ( #12293 )
6 years ago
549d11225a
Add to description of Z_STEPPER_AUTO_ALIGN
...
In response to #12272
6 years ago
2cff0d1f39
Move menu_level_bed_corners to its own file
6 years ago
44f2a82a56
Move axis_homed, axis_known_position to motion.*
6 years ago
946cf8b453
EEPROM read code grouping
6 years ago
f2adb4b9cc
Update German language ( #12280 )
6 years ago
484ca68228
Fix misplaced parentheses ( #12284 )
6 years ago
1d366db764
Tweaks to CR-10S configuration
6 years ago
b5d7f69b51
Followup to #12249
6 years ago
b780b69c62
Use font ascent and descent for line positioning ( #12224 )
6 years ago
9cd3529108
Organize language data, fix Korean and Danish
6 years ago
66d44c72c3
Add fast binary file transfer to SD card option ( #12249 )
6 years ago
72d8adfd1e
Cleanup and refactor EXTENSIBLE_UI ( #12227 )
...
- Add `axis_t`, `extruder_t`, `heater_t`, and `fan_t` to eliminate ambiguity, improve type safety.
- Regularized getter/setter argument order and naming.
- `setAxisPosition` no longer stacks moves in the buffer, allowing it to be called repeatedly on each touch ui tap.
- Implement better manual moves for `EXTENSIBLE_UI` (#12205 )
- Calling `setAxisPosition_mm` no longer buffers the entire move to the new position, but instead causes small moves towards it to be made during the idle loop. This allows the user to adjust the destination even after the move has started and makes the UI feel much more responsive.
- As suggested by @ejtagle, the new code keeps the planner buffer full to ensure smooth motion without stops and starts.
- Change `En`, `Hn` and `FANn` to zero-based indices.
- Labels consistent with the rest of Marlin code.
6 years ago
1946f729fd
STM32 FastIO using register access ( #12276 )
6 years ago
56057bcecd
Fix lcd_impl_status_screen_1
6 years ago
4ed579cafc
Americanized English spelling
6 years ago
9e663a624b
Apply #pragma once to configuration files
6 years ago
98c32d8df1
Fix a config endif label
6 years ago
3583e2b449
Followup to Menu Refactor ( #12275 )
6 years ago
5536228359
G34 Auto-align multi-stepper Z axis ( #11302 )
6 years ago
f9b80e7217
Make getfilename_sorted standard for listings
6 years ago
5ead026967
Fix menu_temp_xx_filament_change menu items
6 years ago
d632e44c8c
[Merge] Refactor LCD menus / screens ( #12199 )
6 years ago
1f9806875c
Update German language ( #12261 )
6 years ago
63ce8baa55
Fix Teensy 3.5/3.6 ADC access for ADC1 ( #12258 )
6 years ago
3a935fd72b
Reduce repetition in menu edit items
6 years ago
b063b1b722
Reorganize includes and declarations
6 years ago
43cf913048
Move SD Card Menu to its own file
6 years ago
0161d3f733
Move Custom User Menu to its own file
6 years ago
3b0d2330b6
Move Delta Calibrate Menu to its own file
6 years ago
6896847210
Move LED Menu to its own file
6 years ago
9cd5471202
Move Job Recovery Menu to its own file
6 years ago
9f11e0284c
Move Filament Change Menu to its own file
6 years ago
d87ab3ed20
Move Advanced Settings Menu to its own file
6 years ago
587a64d80c
Move Bed Leveling Menu to its own file
6 years ago
96f313fb41
Move Info Menu to its own file
6 years ago
423ab029b2
Move Temperature Menu to its own file
6 years ago
489017995e
Move UBL Menu to its own file
6 years ago
a489c9fa52
Move Motion Menu to its own file
6 years ago
3a9ad9f2b1
Move Configuration Menu to its own file
6 years ago
143d4ec043
Move Tune Menu to its own file
6 years ago
829effc1fe
Move Main Menu to its own file
6 years ago
37ff663b02
Convert LIGHTWEIGHT_UI to CPP
6 years ago
a964f098b3
Make dogm status screen a CPP
6 years ago
8055ed24ff
Move font data to a subfolder
6 years ago
774a6e8199
Drop TALL_FONT_CORRECTION
6 years ago
c825c419d4
Convert DOGM / HD44780 impl to CPP files
6 years ago
182b1405d9
LCD conditionals in configurations
6 years ago
2bf18950ab
Refactor LCD menus
6 years ago
ac5f2762b7
Use E_AXIS_N where possible
6 years ago
6fbc87301f
'G29 H' to set a centered square probe area (linear, bilinear) ( #12242 )
6 years ago
c1e8bd6add
Remove STM32 board-specific delays ( #12243 )
...
...and replace with delays for all HAL_STM32 boards.
6 years ago
3c9daf322a
MSG_CNG_SDCARD => MSG_CHANGE_SDCARD
6 years ago
4b7a0a5b39
Require TMCStepper 0.2.2 or newer
...
In reference to #12175
6 years ago
ab8425f1b5
Clean up PROBE_TRIGGERED_WHEN_STOWED_TEST ( #12232 )
6 years ago
3028a620af
Add RACK_AND_PINION_PROBE ( #12218 )
6 years ago
ad60f0691c
Add Creality3D RAMPS pins definitions ( #12229 )
6 years ago
5580773191
Use FastIO, sanity-check LPC SD options, apply formatting ( #12231 )
6 years ago
d015f746cc
Fix some compile warnings ( #12220 )
6 years ago
dacb5324e8
Fix display of Y on Graphical LCD
6 years ago
bf9dd4f4cf
Add helpers for custom text in menu items ( #12214 )
...
For some features it can be useful to write custom text in a menu item. This commit provides helpers to make this easier.
6 years ago
e8031b1152
Add Custom Microstepping options
6 years ago
fbfb48cce0
Indent a block
6 years ago
1a00d1bdaf
Add pullup to USB interrupt line
...
- A pullup on the INT pin is required when the pin is level-active
6 years ago
a07ac6312f
G0 feedrate may be fixed or variable ( #12172 )
6 years ago
53c535a0c1
Remove trailing whitespace
6 years ago
55dec02ca1
Allow X, Y, Z manual move when cold. ( #12209 )
6 years ago
7243101135
z_offset fix for deltas ( #12210 )
6 years ago
9613f00877
Fix getProgress_seconds_elapsed to return seconds
6 years ago
5d487ef40e
Fix null exception due to duration_t of zero ( #12207 )
6 years ago
a9061714f2
Update Italian language ( #12196 )
6 years ago
aebbb2359d
Fix IDEX homing X0 wrong direction ( #12200 )
6 years ago
0a549fd1f2
Fix EXTENSIBLE_UI compile errors ( #12206 )
6 years ago
a80ba8fc6e
Slovak translation update ( #12202 )
6 years ago
e48cbff10d
Fixed redefinition warnings of MSG_HOTEND_TOO_COLD. ( #12203 )
6 years ago
7a04eb3a8b
Fix some comment formatting
6 years ago
2f873a119f
Revert some UBL strings
6 years ago
a93e9e6e9b
Use preheat labels in place of PLA/ABS ( #12194 )
6 years ago
aa72884a6e
Enable use of SERIAL_PORT_2 on HAL_STM32 ( #12197 )
6 years ago
46360f18b4
Bring thermistor_75.h up to speed
6 years ago
e229b831fa
Customizable preheat labels
6 years ago
a553ab82e0
Add e index to _lcd_move_distance_menu
6 years ago
3a46212dd8
Better cold extrusion prevention in LCD menu ( #12189 )
6 years ago
fc31da1114
Implement custom delay/millis for EXTENSIBLE_UI ( #12188 )
6 years ago
3a3ab3391f
Return set_directions() to stepper.cpp ( #12182 )
...
Initial manual Z move can be negative if your stepper is inverted. Leads to bad situations for crashed or initially booted printers.
6 years ago
e5ae7a07d1
Suppress compiler warning
6 years ago
6ee2af5e2d
Simplify pins_TRIGORILLA_14.h ( #12162 )
6 years ago
d801f85963
Correct EEPROM read/write disparities. ( #12169 )
6 years ago
8d3a92fc4a
Followup to millis_t patch
6 years ago
44369d536a
Use millis_t where needed ( #12152 )
6 years ago
b641571098
Replace types.h with millis_t.h
6 years ago
eeef4e630a
Fix compile error in leds.h
6 years ago
9969c06cb5
Fix compiler warning
6 years ago
427c80119a
Hide some menu items when busy: fix typo ( #12164 )
6 years ago
55ac2f4c23
Fix filament runout for idex duplication modes ( #12168 )
6 years ago
b640b3b0d6
Define ST7920 delays for board ARMED ( #12161 )
6 years ago
2e5e689a7f
Fix kill() and ExtensibleUI ( #12160 )
...
* Fix to isPrintingFromMedia()
- isPrintingFromMedia() will now return true even if SD print is paused.
- isPrintingFromMediaPaused() allows UI to determine if the print is paused.
* Don't use _delay_us in minkill (#12145 )
- In HAL_DUE, _delay_us is simply an alias for delay, which causes the board to hang and subsequently reboot due to the watchdog timer.
* Shorten code with IFSD macro
6 years ago
b381cad399
Clean up trailing whitespace
6 years ago
9090065e9f
Move EXTRA_FAN_SPEED above FWRETRACT
6 years ago
4eb798dbdc
Add support for Arm'ed (STM32F4) board ( #12147 )
6 years ago
1fb9b299d4
Add M524 to abort SD printing ( #12155 )
6 years ago
d26d9d5b81
Tweak IS_SD_INSERTED
6 years ago
c6a5c74208
Add parentheses to SD macros
6 years ago
aa9202260d
Fix endstop when no interrupt ( #12158 )
6 years ago
8c02dd971b
Move disable_all_steppers to minkill
6 years ago
3847c08f7e
Disable heaters/steppers before message
6 years ago
71e19baf69
Fix kill => disable_all_heaters => print_job_timer.stop ( #12146 )
...
- Remove `print_job_timer.stop()` from `disable_all_heaters`
- Call `print_job_timer.stop()` for relevant `disable_all_heaters()`.
- Split up `kill()` for watchdog interrupt safety
6 years ago
4cc1c2627e
Update German language ( #12143 )
6 years ago
75a0d46edf
Fix compile warning re: LCD_INFO_SCREEN_STYLE
6 years ago
a81763c237
Pins E sanity check tweak
6 years ago
bc22641002
[2.0.x] Updated Italian Language ( #12148 )
6 years ago
eded90bf87
Updated Azteeg X5 Mini Wifi pins for onboard SD ( #12133 )
6 years ago
27a84fd021
Remove unused option in Anycubic Kossel config ( #12138 )
6 years ago
67a3c5a16a
Alternative info screen (Prusa-style) ( #12132 )
...
* Fix Z value display
* Add HAS_PRINT_PROGRESS
* Alternative Info Screen option
* Add LCD_INFO_SCREEN_STYLE to example configs
6 years ago
5b7dd553d3
Fix sd_mmc_spi_mem capacity; clean up USB code ( #12134 )
...
- Fix an error in the return value of `sd_mmc_spi_read_capacity` which was causing the host OS to read beyond the last sector in the card.
- Clean up the USB flashdrive code and add better debugging.
6 years ago
df768e7d8f
Followup to #12129
6 years ago
3c13c9e3e9
[LPC176x] Fix USEABLE_HARDWARE_PWM macro, cleanup multiple LED support ( #12129 )
6 years ago
a768df83cb
Remove stale variable ( #12136 )
6 years ago
c36773bffb
Update the Ender-4 example config ( #12131 )
...
- Enable filament change menu
- Enable bed-PID
- Enable s-curve acceleration
- Enable some menu items
- Update from Skorpi's new version
- Fix extruder steps, deactivate nozzle clean feature
6 years ago
9c71bff5e8
Update German language ( #12115 )
6 years ago
9deb23aa47
Add missing SerialUSB definition for STM32 HAL ( #12124 )
6 years ago
0519ef0802
Update pins for final RemRam v1.3 board ( #12125 )
6 years ago
3ec3872730
Single Z raise value for all tool-changing / parking ( #12090 )
...
* Universal tool-change Z lift
* Add TOOLCHANGE_ZRAISE to example configs
* Park/unpark changes to example configs
* Implement DEBUG_DXC_MODE
6 years ago
6bdbe3299e
Fix a comment
6 years ago
bc75eb2c64
Cleanup for HAL_spi_Due.cpp
6 years ago
d82bcdeea1
Make PULSE_STOP(E) conditional ( #12121 )
6 years ago
c90e26dfa6
fix normal extruder stepping ( #12118 )
6 years ago
96bbda5d48
remove confusing comment ( #12120 )
6 years ago
f98f4ac7ea
Fix and improve EXTENSIBLE_UI ( #12117 )
...
- Add methods to access print counter data
- Clean up some inconsistent method names
- Clear lcd status after filament change
- Implement `lcd_reset_status` so it works like UltraLCD
6 years ago
8bf596bd4c
RETRACT_ZLIFT => RETRACT_ZRAISE
6 years ago
056561df93
[2.0.x] Enhancements to FILAMENT_RUNOUT_SENSOR ( #12069 )
...
- Added FILAMENT_RUNOUT_DISTANCE_MM option
- Added FILAMENT_MOTION_SENSOR option
6 years ago
cce4931342
Clean up recent contribs
6 years ago
8b5e51c9aa
STM32F4xx modifications for HAL_STM32 ( #12080 )
6 years ago
bf0c809ff2
Update M165 comment
6 years ago
9ac9649183
Mixer - update descriptions ( #12108 )
6 years ago
9bf5d4331c
Clear up some compiler warnings
6 years ago
0139762a96
Fix a sanity check
6 years ago
2ecb124e42
Fix trailing whitespace
6 years ago
f56968ba0b
New Continuous Filament Mixer ( #12098 )
6 years ago
2d2cd628c6
Update German language ( #12094 )
6 years ago
84b59d58fb
Clean up whitespace
6 years ago
06e2afe8e0
[2.0.x] Reduce HOMING_FEEDRATE_XY for Ender 3 ( #12105 )
...
Homing on the Ender 3 with HOMING_FEEDRATE_XY set to 50*60 was shown (#12074 ) to cause the end-stop micro-switches to bottom out, causing the carriage for both X and Y axis to physically crash into the micro switch. Reducing the homing speed prevents the switches from bottoming out.
6 years ago
af939c158a
Option for G0 to have a separate feedrate ( #12089 )
6 years ago
e5b4bf22d4
Remove debug output from flash persistent store implementation
6 years ago
42fb7c14b0
Update the sdcard usb sharing config and apply to Re-ARM
6 years ago
254b68fe2c
servo update
6 years ago
870bfd08f5
usb and sdcard sharing improvements
...
* Add traceback after watchdog timeout
Add the cpability to perform a traceback following a watchdog timeout.
* Enhanced hardware SPI
Allow use of either SSP0 or SSP1.
Ensure that no data is left in I/O buffers after calls to enable sharing of SSP hardware.
* Make flash emulation of eeprom the default
Make use of flash for eeprom storage the default. This means that usage of eeprom will not cause USB drive mount/unmount operations.
* Allow sharing of SD card
SD card I/O operations from the USB stack take place in idle loop, rather than at interrupt time. Allowing sharing of the SPI bus.
New configuration options to allow usage of the SD card to be specified.
* Fix problem with hardware SPI pins
6 years ago
5ddf52d58e
[HAL][LPC176x] Pull out framework into separate repository
...
Framework and build platform now located at https://github.com/p3p/pio-framework-arduino-lpc176x and https://github.com/p3p/pio-nxplpc-arduino-lpc176x respectively
fix mkssbase leds
move hardware serial
remove hardware/software serial
Hardware Serial extraction
HardwareSerial ISRs
fix disabled serial2 causing Serial object to link
move usb devices out to framework
separate out adc/pwm peripheral function from hal.cpp
fix includes
remove unused pwm init
move adc
HAL header update
templated filtered adc
LPC1769 platform
6 years ago
213e94bce2
[2.0.x] Updated slovak translation ( #12059 )
6 years ago
a40458405a
Fix datasize error when FWRETRACT is disabled ( #12086 )
6 years ago
951b25163e
Extend M217 with configurable park/raise ( #12076 )
6 years ago
ea13a77dcb
Fixed Z-Probes NO/NC for Anycubic Kossel ( #12083 )
6 years ago
ab9d5eb38d
Add Bootscreen Animation ( #12077 )
6 years ago
26208a5c2f
Clean up some boot screens
6 years ago
9b6be0ae0f
Fix lite status screen SD %
6 years ago
af3bf6c956
Tweak config spacing
6 years ago
a44ef27897
Outdent singlenozzle toolchange code
6 years ago
d338e4d875
Fix singlenozzle toolchange cold extrusion test
6 years ago
25b980dddb
Remove erroneous Pin 12 definition
...
There is no switchable Power Supply. Don't put it on Pin 12.
(Pin 12 is actually FAN1)
6 years ago
ddaef1a60c
Clean trailing whitespace
6 years ago
1407afad73
Move SENSITIVE_PINS to its own file
6 years ago
45e738876a
Add stepper MS3 support
...
Co-Authored-By: TheLongAndOnly <thelongandonly@users.noreply.github.com>
6 years ago
d43d4e4219
Refactor PRINTER_EVENT_LEDS, apply to M303 ( #12038 )
...
Co-Authored-By: Giuliano Zaro <gmagician@users.noreply.github.com>
6 years ago
d8d76cd2ba
[2.0.x] Italian language update ( #12060 )
6 years ago
e8d2cf4fb5
EEPROM followup (tmc_stepper_current_t)
6 years ago
50cbca4c55
Hide some menu items when busy
6 years ago
3cb5517ddb
Make singlenozzle tool-change honor no_move ( #12056 )
...
...Set no move earlier so it applies
6 years ago
d332fcb8fa
Fix firmware-retract compile errors ( #12061 )
6 years ago
43940d59ed
Fix trailing spaces
6 years ago
b2c1cd7eda
Allow cold change of active extruder ( #12055 )
...
Followup to #11994
6 years ago
d556dc1865
Fix and improve EEPROM storage ( #12054 )
...
* Clean up Temperature PID
* Improve EEPROM read/write/validate
* Group `SINGLENOZZLE` saved settings
* Group planner saved settings
* Group filament change saved settings
* Group skew saved settings
* Group `FWRETRACT` saved settings
6 years ago
9b5c1a5e77
Fix EEPROM checksum bug
...
Addressing #12048
6 years ago
272d4a5167
Apply #pragma once
6 years ago
07d33849b0
Fix unused var warning, apply ENABLED
6 years ago
a3e8cb1e44
[2.0.x] Ender-4 small improvements in Configuration ( #11843 )
6 years ago
cf5284cdf2
Add SD Firmware Update capability ( #12043 )
...
Co-Authored-By: timoxd7 <timoxd7@users.noreply.github.com>
6 years ago
0bd54392b7
Use uint8_t in EEPROM code
6 years ago
ce82015d5f
Fix include in G80
6 years ago
cef1de89d0
Fixed incorrect axis index. ( #12051 )
6 years ago
d6d48e63fb
Allow #defined TYPE arg to ultralcd menu macros ( #12041 )
...
Previously, it was not possible for the TYPE argument to ultralcd menu macros to itself be a #defined value. This made it difficult to create variables to set many related menu items to a common precision that could be easily changed.
6 years ago
2ef7175b42
Update Ender-2 BED_MAXTEMP ( #12042 )
...
Also added details to the README to make sure the Ender-2 status is properly documented.
6 years ago
5f6aabccbe
Tweak M48 spacing
6 years ago
ec9aa4f468
[2.0.x] Miscellaneous fixes ( #12039 )
...
* Allow override of soft SPI pins in `pins_*.h`
* Add default case to avoid compiler warning.
* Additional pin definitions for Archim 2.
* Einsy Retro has same timings as Einsy Rambo.
6 years ago
906a24fa81
Extensible user interface API ( #11193 )
6 years ago
ee253991d4
Various fixups for single-nozzle filament swap ( #12036 )
6 years ago
8dbb305e8e
Fix "Missing separator" errors. ( #12035 )
...
- Makefiles require tabs (not spaces) before shell commands.
- Other indentation can either be space or tabs.
6 years ago
55e810d512
Fix G80 compilation
6 years ago
d5017e2788
Add status screen with 4 nozzles
6 years ago
7db0113b53
Improve E_AXIS_N macro
6 years ago
191df5e17d
Correct PWM_PIN behavior for STM32 HALs ( #12027 )
6 years ago
f2ecf8d510
Add option to control Solenoids under PARKING_EXTRUDER ( #12028 )
6 years ago
74cd6cb4fc
Single nozzle filament change ( #11994 )
6 years ago
bfcf570d68
Try ISR_ALIASOF for Endstop Interrupts
6 years ago
c0d9058e25
Shorten an Italian menu title ( #12034 )
...
…and change a multi-use "back" menu item.
6 years ago
dffb4c63dc
[2.0.x] TMC2660 followup ( #12029 )
...
* Don't react to s2g on TMC2660. False positives
* Init with sensorless probing as well
6 years ago
d6b0fbd771
Use uint8_t for all fan speeds ( #12032 )
6 years ago
cb7844c8d4
Save PROGMEM on serial prefixes ( #12033 )
...
With default config and `EEPROM_SETTINGS`, saves over 200 bytes of PROGMEM.
6 years ago
07db08e39d
Fix EXTRUDER_AUTO_FAN_SPEED comment
6 years ago
ca0e308105
Fix up some units comments
6 years ago
65b8f3821b
Suppress temperature.h compile warning
6 years ago
c447d75916
Add support for TMC2660 ( #11998 )
6 years ago
cf0b9eb37c
no need to use destination in do_pause_e_move
6 years ago
e8d677620c
Use NUM_SERVOS in EEPROM code
...
Fix #12015
6 years ago
0fcdfdeed6
Followup to #12017
6 years ago
acac2adfc8
Add support for MeCreator2 ( #12017 )
6 years ago
49823a4939
Fix broken jerk handling ( #12019 )
...
Fix #12004
6 years ago
52a37913c1
Extend and apply some corrections
6 years ago
77b9a41f1f
Add G-code extensions to example configs
6 years ago
e09c144674
Add CNC-like G-code options
6 years ago
33056046a3
STM32 non-generic PWM_PIN and USEABLE_HARDWARE_PWM ( #12016 )
6 years ago
d5141c4e03
Fix up leading/trailing whitespace
6 years ago
03fc4d31d0
Makefile support for 32-bit Archim board and new TMC library ( #11997 )
...
* Support new TMC library and 32-bit Archim board
- Added IS_MCU flag
- When IS_MCU flag is 1, AVR compiler will be used
- When IS_MCU flag is 0, ARM compiler will be used
- Added support for new TMC library
- Added support for a 32-bit Archim board, which could probably be used as a basis for other 32-bit boards.
6 years ago
65b36642f8
Fix Anycubic Kossel config
6 years ago
fc326b3dde
Add USB_FLASH_DRIVE_SUPPORT to examples
...
Co-Authored-By: marcio-ao <marcio@alephobjects.com>
6 years ago
2067619a26
Add USB_FLASH_DRIVE_SUPPORT
6 years ago
07fe8d28be
[2.0.x] Partial Italian revert ( #12008 )
...
- Use a comma for decimals just in one message has not been a good idea.
- Full comments translation
6 years ago
517b4f4cd4
Fix lightweight UI hotends display
6 years ago
72a750e0eb
[2.0.x] Update Italian language ( #11996 )
6 years ago
bb561baf9e
Tweak some config comments
6 years ago
fcf6d127fd
STM32 timer simplification ( #11995 )
...
Prescalers aren't calculated for the given target frequency.
Stepper timer should run at 2 Mhz and temperature timer at 72 Khz.
6 years ago
8daadd2c8c
Fix TMC_DEBUG undefined report_tmc_status ( #11993 )
6 years ago
c40ea1f0fd
Update EEPROM_VERSION
...
And set EEPROM_OFFSET to 0, since the historical 100 skipped bytes are never used.
6 years ago
1358bd9319
Make MAX_EXTRUDERS always 6
6 years ago
001f26b642
Template struct simplification for serial ( #11990 )
6 years ago
348004c34f
STM32F7 HAL using the official STM32 Arduino Core ( #11750 )
6 years ago
3e58b3a5d4
Followup to #11943
6 years ago
c3229e1b34
Migrate to a new TMC library ( #11943 )
6 years ago
2abf3d258d
Korean language translation support ( #11987 )
6 years ago
d6955f25b2
Expand serial support in DUE/AVR hals exploiting the templated MarlinSerial classes ( #11988 )
6 years ago
f6f2246f59
Templatized serial classes ( #11982 )
6 years ago
ee53f7d813
Revert header reorg.
6 years ago
d619ba2685
Tweak STM32F4 config
6 years ago
d777cef837
fixed minimum macro ( #11986 )
6 years ago
e3f7b69105
Add PROBING_STEPPERS_OFF ( #11984 )
...
Co-Authored-By: houseofbugs <houseofbugs@gmail.com>
6 years ago
0e5bcdf695
Make DISABLE_INACTIVE_EXTRUDER a simple switch
6 years ago
0dedb3e139
Reorganize some core headers ( #11983 )
6 years ago
ab4549d2bc
[2.0.x] Add simultaneous retraction for mixing extruder ( #11941 )
6 years ago
c75f5a376b
Tweak some comments
6 years ago
f4c625d3a1
Ensure MIN/MAX overrides
6 years ago
3019713402
Reorganize some enums
6 years ago
606a4362b3
Reduce STM32F4 compile warnings
6 years ago
b3154b2120
Apply MOVE_Z_WHEN_IDLE to example configurations
...
Co-Authored-By: dot-bob <gibben@gmail.com>
6 years ago
b0fd8f2d74
Add option to move Z on double-click when idle
6 years ago
389376c40e
Clean up softspi.h
6 years ago
e78bdd654d
Clean up BABYSTEP options
6 years ago
8ae113ff36
Show zprobe_zoffset when BABYSTEP_HOTEND_Z_OFFSET is disabled ( #11973 )
6 years ago
2e98437392
Clean up main menu ( #11972 )
6 years ago
6d862b2916
Home before level corners, if needed ( #11976 )
...
…and add a consistent homing screen for all LCD pre-homing.
6 years ago
11ac75edcb
Use PGM_P for PSTR pointers ( #11977 )
6 years ago
4d5566a6b7
Add filament runout sensor menu item ( #11971 )
6 years ago
8489673cea
Adjust some HAL formatting
6 years ago
fb8a07660a
Followup to minmax patch
...
Co-Authored-By: Palatis <palatis@gmail.com>
6 years ago
3c40933713
Remove trailing spaces, old comment
6 years ago
a3ec805c97
Anycubic Kossel Linear+: corrected DELTA_DIAGONAL_ROD ( #11964 )
6 years ago
b30ca652ae
Replace MIN# / MAX# with variadic MIN / MAX ( #11960 )
6 years ago
e10f730478
Tweak vector_3::apply_rotation
6 years ago
e2ab78d876
Fix SERIAL_PORT_2 sanity check
6 years ago
a644d8cb93
Avoid copies in vector and matrix ( #11959 )
6 years ago
693865a649
Fix some whitespace
6 years ago
9903305dda
Merge pull request #9582 from tcm0116/2.0.x-sensorless_probing
...
[2.0.x] Add TMC2130 sensorless probing
6 years ago
14df753086
Correction for block->mix_steps
...
Fix #11484
6 years ago
2ecfda80ac
Improve support for JTAG/SWD pins reuse ( #11963 )
...
STM32 can reuse JTAG and SWD pins separately. Add `DISABLE_DEBUG` option to disable both interfaces and retain `DISABLE_JTAG` to disable JTAG only.
6 years ago
bb47009656
Apply sensorless changes to example configs
6 years ago
3286325044
Add TMC2130 sensorless probing
6 years ago
7d5c336c56
Corrections for dylsexic TMC
6 years ago
d89d8fe852
Fix Busy State in temperature.cpp
...
Fix #11954
6 years ago
70e7a465d8
[2.0.x] Fix compile error ( #11951 )
...
Fix compile error intruduced with M109 modification
6 years ago
935b120949
Anycubic Kossel: probe closer to the edge ( #11950 )
6 years ago
1410e79e7f
Ensure M109 handles autotemp
6 years ago
e4389f7d23
Standard methods to wait for heating ( #11949 )
6 years ago
bdc9889d3a
Fix a sanity check
6 years ago
321f9140d1
Followup to #11904
6 years ago
23114aeb81
Fix garbled M119 output. Honor NUM_RUNOUT_SENSORS ( #11948 )
6 years ago
1667ed9d1c
Pause should use ECHOLNPGM
6 years ago
93839e2f73
Add option to enable/disable autoretract altogether ( #11904 )
6 years ago
ad21a4f07b
Tweaks to HAL format and order
6 years ago
b682a1961a
Tweak STM32F7 TMC2660 class
6 years ago
a0a3b23e35
Reduce Raptor bootscreen by 144 bytes
6 years ago
95d793456b
Add Formbot Raptor config, fix other Formbot configs ( #11926 )
6 years ago
d016b572e3
[2.0.x] Add pin configuration for Fysetc F6 ( #11932 )
6 years ago
84926b1d5a
HAL general support for DISABLE_JTAG option ( #11211 )
...
Some STM32-based boards may use multiplexed JTAG pins as IO. Up to now the `DISABLE_JTAG` option (defined in pins files) was only supported for AT90-based boards. This commit generalizes the code and adds support for boards based on STM32F1 and STM32F4.
6 years ago
c575c5d5f6
Bring example configs up to date ( #11939 )
6 years ago
6b1a4f30a8
Fix case of T-Rex 3 _Statusscreen.h
6 years ago
ab7bfa86e2
Fix case of T-Rex-3 _Statusscreen.h
6 years ago
241168926d
Update some configs
6 years ago
cb6454118c
Workaround for Pronterface M29
6 years ago
eeab4141db
[2.0.x] Anycubic Trigorilla 14 pins tweak ( #11869 )
6 years ago
cb9dc56630
Add GT2560 v3 support ( #11914 )
6 years ago
f2e630a05e
Stow probe on probing failed ( #11936 )
...
Prevents probe from being left down should probing fail and print job continue
6 years ago
0b602ae101
[2.0.x] Fix Anycubic Kossel with Probe V1, stuck LCD message after stow ( #11929 )
6 years ago
dc11131656
[2.0.x] fix possible race condition ( #11923 )
...
Fix some commits done in #11900
6 years ago
d6b9327c11
Followup for Endstop Noise Threshold
...
Followup to #11912
6 years ago
aa6e8e9325
Tweak some config comments
6 years ago
5490a664f5
Expose: Homing Validation and Endstop Noise Threshold ( #11912 )
6 years ago
cee34f7290
Followup for BABYSTEP_HOTEND_Z_OFFSET ( #11916 )
6 years ago
884ad75cb8
Update config files
6 years ago
18e456d38d
[2.0.x] fix home endstop bug (DON'T MERGE, needs discussion) ( #11900 )
6 years ago
6742026568
Followup for 6 extruders
6 years ago
04bdff4115
Add a blank line
6 years ago
ccbd045f02
Fixed warning about comparing signed to unsigned ( #11909 )
6 years ago
Ludy