348004c34f
STM32F7 HAL using the official STM32 Arduino Core ( #11750 )
6 years ago
3e58b3a5d4
Followup to #11943
6 years ago
c3229e1b34
Migrate to a new TMC library ( #11943 )
6 years ago
2abf3d258d
Korean language translation support ( #11987 )
6 years ago
d6955f25b2
Expand serial support in DUE/AVR hals exploiting the templated MarlinSerial classes ( #11988 )
6 years ago
f6f2246f59
Templatized serial classes ( #11982 )
6 years ago
ee53f7d813
Revert header reorg.
6 years ago
d619ba2685
Tweak STM32F4 config
6 years ago
d777cef837
fixed minimum macro ( #11986 )
6 years ago
e3f7b69105
Add PROBING_STEPPERS_OFF ( #11984 )
...
Co-Authored-By: houseofbugs <houseofbugs@gmail.com>
6 years ago
0e5bcdf695
Make DISABLE_INACTIVE_EXTRUDER a simple switch
6 years ago
0dedb3e139
Reorganize some core headers ( #11983 )
6 years ago
ab4549d2bc
[2.0.x] Add simultaneous retraction for mixing extruder ( #11941 )
6 years ago
c75f5a376b
Tweak some comments
6 years ago
f4c625d3a1
Ensure MIN/MAX overrides
6 years ago
3019713402
Reorganize some enums
6 years ago
606a4362b3
Reduce STM32F4 compile warnings
6 years ago
b3154b2120
Apply MOVE_Z_WHEN_IDLE to example configurations
...
Co-Authored-By: dot-bob <gibben@gmail.com>
6 years ago
b0fd8f2d74
Add option to move Z on double-click when idle
6 years ago
389376c40e
Clean up softspi.h
6 years ago
e78bdd654d
Clean up BABYSTEP options
6 years ago
8ae113ff36
Show zprobe_zoffset when BABYSTEP_HOTEND_Z_OFFSET is disabled ( #11973 )
6 years ago
2e98437392
Clean up main menu ( #11972 )
6 years ago
6d862b2916
Home before level corners, if needed ( #11976 )
...
…and add a consistent homing screen for all LCD pre-homing.
6 years ago
11ac75edcb
Use PGM_P for PSTR pointers ( #11977 )
6 years ago
4d5566a6b7
Add filament runout sensor menu item ( #11971 )
6 years ago
8489673cea
Adjust some HAL formatting
6 years ago
fb8a07660a
Followup to minmax patch
...
Co-Authored-By: Palatis <palatis@gmail.com>
6 years ago
3c40933713
Remove trailing spaces, old comment
6 years ago
a3ec805c97
Anycubic Kossel Linear+: corrected DELTA_DIAGONAL_ROD ( #11964 )
6 years ago
b30ca652ae
Replace MIN# / MAX# with variadic MIN / MAX ( #11960 )
6 years ago
e10f730478
Tweak vector_3::apply_rotation
6 years ago
e2ab78d876
Fix SERIAL_PORT_2 sanity check
6 years ago
a644d8cb93
Avoid copies in vector and matrix ( #11959 )
6 years ago
693865a649
Fix some whitespace
6 years ago
9903305dda
Merge pull request #9582 from tcm0116/2.0.x-sensorless_probing
...
[2.0.x] Add TMC2130 sensorless probing
6 years ago
14df753086
Correction for block->mix_steps
...
Fix #11484
6 years ago
2ecfda80ac
Improve support for JTAG/SWD pins reuse ( #11963 )
...
STM32 can reuse JTAG and SWD pins separately. Add `DISABLE_DEBUG` option to disable both interfaces and retain `DISABLE_JTAG` to disable JTAG only.
6 years ago
bb47009656
Apply sensorless changes to example configs
6 years ago
3286325044
Add TMC2130 sensorless probing
6 years ago
7d5c336c56
Corrections for dylsexic TMC
6 years ago
d89d8fe852
Fix Busy State in temperature.cpp
...
Fix #11954
6 years ago
70e7a465d8
[2.0.x] Fix compile error ( #11951 )
...
Fix compile error intruduced with M109 modification
6 years ago
935b120949
Anycubic Kossel: probe closer to the edge ( #11950 )
6 years ago
1410e79e7f
Ensure M109 handles autotemp
6 years ago
e4389f7d23
Standard methods to wait for heating ( #11949 )
6 years ago
bdc9889d3a
Fix a sanity check
6 years ago
321f9140d1
Followup to #11904
6 years ago
23114aeb81
Fix garbled M119 output. Honor NUM_RUNOUT_SENSORS ( #11948 )
6 years ago
1667ed9d1c
Pause should use ECHOLNPGM
6 years ago
93839e2f73
Add option to enable/disable autoretract altogether ( #11904 )
6 years ago
ad21a4f07b
Tweaks to HAL format and order
6 years ago
b682a1961a
Tweak STM32F7 TMC2660 class
6 years ago
a0a3b23e35
Reduce Raptor bootscreen by 144 bytes
6 years ago
95d793456b
Add Formbot Raptor config, fix other Formbot configs ( #11926 )
6 years ago
d016b572e3
[2.0.x] Add pin configuration for Fysetc F6 ( #11932 )
6 years ago
84926b1d5a
HAL general support for DISABLE_JTAG option ( #11211 )
...
Some STM32-based boards may use multiplexed JTAG pins as IO. Up to now the `DISABLE_JTAG` option (defined in pins files) was only supported for AT90-based boards. This commit generalizes the code and adds support for boards based on STM32F1 and STM32F4.
6 years ago
c575c5d5f6
Bring example configs up to date ( #11939 )
6 years ago
6b1a4f30a8
Fix case of T-Rex 3 _Statusscreen.h
6 years ago
ab7bfa86e2
Fix case of T-Rex-3 _Statusscreen.h
6 years ago
241168926d
Update some configs
6 years ago
cb6454118c
Workaround for Pronterface M29
6 years ago
eeab4141db
[2.0.x] Anycubic Trigorilla 14 pins tweak ( #11869 )
6 years ago
cb9dc56630
Add GT2560 v3 support ( #11914 )
6 years ago
f2e630a05e
Stow probe on probing failed ( #11936 )
...
Prevents probe from being left down should probing fail and print job continue
6 years ago
0b602ae101
[2.0.x] Fix Anycubic Kossel with Probe V1, stuck LCD message after stow ( #11929 )
6 years ago
dc11131656
[2.0.x] fix possible race condition ( #11923 )
...
Fix some commits done in #11900
6 years ago
d6b9327c11
Followup for Endstop Noise Threshold
...
Followup to #11912
6 years ago
aa6e8e9325
Tweak some config comments
6 years ago
5490a664f5
Expose: Homing Validation and Endstop Noise Threshold ( #11912 )
6 years ago
cee34f7290
Followup for BABYSTEP_HOTEND_Z_OFFSET ( #11916 )
6 years ago
884ad75cb8
Update config files
6 years ago
18e456d38d
[2.0.x] fix home endstop bug (DON'T MERGE, needs discussion) ( #11900 )
6 years ago
6742026568
Followup for 6 extruders
6 years ago
04bdff4115
Add a blank line
6 years ago
ccbd045f02
Fixed warning about comparing signed to unsigned ( #11909 )
6 years ago
1104054d73
2.0 IDEX Independent z offset and other fixes ( #11862 )
...
* Add Formbot Raptor board
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>
* Add a second Z probe Z offset
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>
* Modify method to utilize live adjustment of hotend z offset
Should probably move config option to babystepping and rename as it may now apply to all multiextruder systems
* Move config item and catchup other code to current method
6 years ago
217e0efd20
General option PAUSE_BEFORE_DEPLOY_STOW ( #11905 )
6 years ago
849dea92a8
Move probe extras below probe types
6 years ago
a2b0260f0f
Update Sublime files
6 years ago
a4cdffdd69
Support for manually deployed fixed probes ( #11899 )
6 years ago
ddcbf80f23
Followup for Z_TRIPLE_ENDSTOPS
6 years ago
c411e7eb0d
[2.0.x] Squelch compiler warnings seen with -Wall ( #11889 )
6 years ago
83105590a0
Better default values for Mesh Inset
6 years ago
4163c1a514
Fix end stop and Z-probe reporting logic
6 years ago
ea9eb2fc8f
Fix servo angles in config-store
6 years ago
d3d6be8210
Add MAX7219 reverse units option ( #11860 )
6 years ago
beab9733f8
Remove extra clauses in config-store
6 years ago
5a74b12b45
Followup to #11769
6 years ago
f38570ac55
Add custom user menu title ( #11769 )
6 years ago
17494099a9
Fix parking_extruder_tool_change
...
Fix #11872
6 years ago
140caf99b8
E0_CS_PIN moved from A13 to A15 on RAMPS-FD v2.2 ( #11865 )
6 years ago
10590c2f80
Fix some fan conditionals
6 years ago
e4ee607fc8
Fix Dual X FRS in M600
...
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>
6 years ago
bae8f82ba8
[2.0] Fix Mixing Extruder mixing factors ( #11861 )
6 years ago
c5e5cc5e9f
Fix some trailing whitespace, macros
6 years ago
54bd124665
2.0.x: Fix normalize_mix() ( #11856 )
...
Mix factors needed to be updated consistent with the recent Stepper/Planner code refactor.
6 years ago
5fbfbde532
Fix example file to pull in correct pins file
6 years ago
378f354939
IDEX Scaled Duplication is still under development
...
Take it out of the menu until it is tested and working.
6 years ago
65045ba54b
tmc_util fix part 2
...
Followup to 115abf9
6 years ago
09a2bee8aa
Support more filament runout sensors in M119 ( #11851 )
6 years ago
115abf9c53
Fix syntax error in front of `tmc_axes`
6 years ago
0780913848
IDEX Improvements ( #11848 )
6 years ago
39732838b4
Tweak indent of Chinese languages
6 years ago
53bd0b55cb
Followup for 6 extruders
6 years ago
1718eff54a
Code changes supporting up to 6 extruders
6 years ago
f5c210d33d
Config changes supporting up to 6 extruders
6 years ago
d948c6e867
RADDS Extension Board V3 support
6 years ago
c437bb08f1
Overhaul of the planner ( #11578 )
...
- Move FWRETRACT to the planner
- Combine leveling, skew, etc. in a single modifier method
- Have kinematic and non-kinematic moves call one planner method
6 years ago
8323a08642
Clean up some whitespace
6 years ago
6286afd456
Add Triple-Z options to example configs
6 years ago
1a6f2b29b8
Add support for Triple-Z steppers/endstops
6 years ago
bc06406d7d
Fix Anycubic Kossel config (probe crash) ( #11832 )
6 years ago
66f83d33e6
Fix some config comments
6 years ago
84ed9b5a63
Send "G33 S P1" for Delta Height Calibration ( #11831 )
6 years ago
215eee4fe5
Use 'friend' to access set_directions
6 years ago
ff51e7322d
Fix for Stepper::set_directions() compilation error ( #11838 )
6 years ago
809b232fa2
Fix stepper directions after M501/M502
...
See https://github.com/MarlinFirmware/Marlin/issues/11103#issuecomment-421387611
Co-Authored-By: tcm0116 <tcm0116@users.noreply.github.com>
6 years ago
f79a5a9dee
Tweak spacing of L6470 options
6 years ago
c37d3ae97d
[2.0.x] Fix NOZZLE_PARK_FEATURE for Anycubic Kossel ( #11812 )
6 years ago
4fb2134f00
Fix non-sensical values for Zonestar themistor table ( #11817 )
...
Values taken from Zonestar firmware for P802QA with a Melzi board. Timestamps from the firmware package are from April 2016.
6 years ago
b220a825a7
Fix raw_filwidth_value error
6 years ago
1933d5d6fb
Fix SD autostart with no LCD
6 years ago
8bce5370c7
Updated slovak translation ( #11807 )
6 years ago
64d629ba2a
[2.0.x] Italian language fix ( #11796 )
6 years ago
8584d3697d
Fix servo count define conflict
...
`MAX_SERVOS` => `NUM_SERVO_PLUGS`
6 years ago
06949ae510
Fix MSG_FILAMENT_CHANGE_HEAT_1 for small LCD
6 years ago
d882717d98
Save some PROGMEM with constexpr ( #11798 )
...
When possible, make `active_extruder` a `constexpr` to save some PROGMEM.
6 years ago
4f883d5971
[2.0.x] Extruder-Distinct Linear Advance K Factors ( #11789 )
6 years ago
fe9f088d60
[2.0.x] Anycubic LinearPlus, Trigorilla 1.4 ( #11730 )
6 years ago
b6aae2b322
Tweak RAMPS_FD_V1 pins
6 years ago
7391e23332
Fix RigidBoard FAN_PIN collision
6 years ago
53b8c3bd66
Add EXTERNAL_CLOSED_LOOP_CONTROLLER to examples
6 years ago
1b6bc19427
Add external closed loop controller support
6 years ago
2ebfe90be9
Add custom preheat temp to filament change ( #11475 )
6 years ago
69d0ed5791
[2.0.x] Fix ambiguous function call (SERIAL_PROTOCOL_F) when using Arduino_Core_STM32 ( #11747 )
6 years ago
d32c4efc77
Fix some trailing whitespace
6 years ago
bc1ba998b2
[2.0.x] Fix undefined symbol 'g29_in_progress' ( #11781 )
6 years ago
bad225dc04
Fix mesh leveling compile errors ( #11768 )
6 years ago
d783400330
Updates to STM32F7 HAL, for completeness ( #11770 )
6 years ago
72af8e0f02
Patch extruder_advance_K edit menu
...
Fix #11776
6 years ago
7e8c073fba
Fix extruder stops extruding with LA ( #11758 )
6 years ago
0c01099f17
hop_amount => current_hop
6 years ago
eafd62308e
Use TMC2208Stepper v0.2.5 ( #11714 )
6 years ago
e25d2ae4a2
[2.0.x] SWITCHING_TOOLHEAD ( #11623 )
6 years ago
f417408df1
[STM32F1] Fix HAL for new PlatformIO ( #11749 )
6 years ago
3d7f2c1fde
Fix directory name to be consistent ( #11745 )
6 years ago
a9c98a0e47
Create _Bootscreen.h
6 years ago
9f85d3a9cb
Create _statusscreen.h
6 years ago
e2e7b1d705
Break out support of the T-Rex 3
6 years ago
67996c2b66
Break out support for the T-Rex 3
6 years ago
9c8d9d282f
Break out support for Formbot T-Rex3 from previous versions
6 years ago
e3aac59637
Create pins_FORMBOT_TREX3.h
6 years ago
f580247581
Create pins_FORMBOT_TREX2.h
6 years ago
073857646b
seperate the T-Rex2 and T-Rex3 support
6 years ago
fe4fc2883b
Add support for Formbot T-Rex3
6 years ago
2a61c9a939
Various fixups to configs, spacing, etc.
6 years ago
b3efbc6e6e
Add MANUAL_E_MOVES_RELATIVE to more configs
6 years ago
679e4602fe
Add MANUAL_E_MOVES_RELATIVE to examples
6 years ago
beb51c2d58
Show manual extrusion moves as relative in LCD
...
- Implements FR#11724
- Old behavior can be restored by commenting out MANUAL_E_MOVES_RELATIVE
6 years ago
d10f29ae2e
Pass segment length in G2-G3
6 years ago
dcfde2317f
Pass segment length in prepare_kinematic_move_to ( #11737 )
6 years ago
d5379ee9d6
Fix search for white space in enqueued commands
6 years ago
8d5bea073b
Assume one Max7219 unit if not specified
6 years ago
9651ceb36b
Correct spelling of #endif
6 years ago
b213a89ef5
Sanity-check NOZZLE_PARK_POINT
6 years ago
86ee74731e
Comment for RADDS + RRDFGSC
6 years ago
ae1271b2ae
RADDS: Update Full Graphic Display Pins ( #11731 )
6 years ago
650d4313c4
Bring some configs up to date
6 years ago
530a13ab6c
[2.0.x] SECURITYFIX missing max temp error when PID is used ( #11717 )
6 years ago
12fded46c2
Correct some FR strings
...
Co-Authored-By: pipersw <pipersw@users.noreply.github.com>
6 years ago
aefc2f7cf9
Add Anet A2 and A2 Plus Configurations ( #11677 )
6 years ago
72fdb6bab3
Fix SWITCHING_NOZZLE zdiff ( #11683 )
6 years ago
8b837dc3ad
No need for last \n in G-code items
6 years ago
d1ceaf5550
[2.0.x] Followup to IDEX changes ( #11707 )
6 years ago
d62f4df0b7
Disable LCD Pins used by new Max7219 hook up if in that mode
6 years ago
fa772c31bf
Provide more options for Max7219 connection on Formbot
6 years ago
8e18e48d49
Merge pull request #11610 from Freeviv/bugfix-2.0.x
...
[2.0.x] Editable servo angles
6 years ago
59e76e5fdf
[2.0.x] Fix planner computation ( #11708 )
...
Fix #11697
6 years ago
509ee44611
Boot and status file should not have been added to main directory!
6 years ago
f8abe12a9c
Boot and status file should not have been added to main directory!
6 years ago
7680b64aa6
IDEX clean up ( #11690 )
6 years ago
49e107cea9
Restrict SW serial to AVR ( #11696 )
6 years ago
18f1af2dca
Fix up Teensy tests, servo sanity
6 years ago
74a04aed55
Fix compile error with NO_LCD_MENUS
6 years ago
509e1cf2bd
Add *_DRIVER_TYPE to remaining configs
6 years ago
d55f44edba
Printcounter improvements ( #11689 )
6 years ago
6a3207391f
Remove obsolete HAL_timer_restrain
6 years ago
e3fc9aa35f
Update some config comments
6 years ago
136860e8bb
Sanity-check SERVO pin for servo probes
6 years ago
66de50f5f8
Updated slovak translation ( #11684 )
6 years ago
ada85d5585
Improve HOTEND OFFSET Z display precision to 3 ( #11686 )
6 years ago
607c1e58d9
Improve HOTEND OFFSET Z display precision to 3 ( #11685 )
6 years ago
3e81745e81
Fix issues, make optional
6 years ago
aa80e448e2
Store servo angles in EEPROM
6 years ago
9953213513
Add EDITABLE_SERVO_ANGLES to example configs
6 years ago
0966bdcbc4
Reorganized ultralcd menu (10317) ( #10360 )
...
Replaced "Prepare" and "Control" menus with "Movement", "Temperature", "Configuration" and "Advanced Settings"
6 years ago
e40a3eef04
Support for Anet A2 Plus
6 years ago
32e38fee74
Update Controller Fan for Y2,Z2
6 years ago
59cf217e77
Fix 5 mixing steppers
6 years ago
2a2e8c314e
Suppress emergency parser G-code errors
...
Co-Authored-By: srieche <srieche@users.noreply.github.com>
6 years ago
7ecb8b4af5
[2.0.x] Teensy 3.1 and 3.2 support ( #11460 )
6 years ago
409a0632af
[2.0.x] Add Morpheus Board support ( #11651 )
6 years ago
0f14977b5d
LIGHTWEIGHT_UI: Allow feedrate % to exceed 255% ( #11656 )
...
- Changed type of integer used for feedrate percentage from uint8_t to uint16_t.
6 years ago
6dc9553aa5
Fix SWITCHING_NOZZLE compile error ( #11657 )
6 years ago
a15e570d3b
Fix SD progress with Lite Status Screen
...
Co-Authored-By: Lê Hoàng <icy.lord.love.angel@gmail.com>
6 years ago
66966dbd69
Tweak comments for newer multiplexer
6 years ago
933d833ec8
Tweak some Anet A6 comments
6 years ago
d1c9517903
Followup to hotend_offset[Z] patch
6 years ago
e2b8fc4f17
Reduce some debug strings
6 years ago
b71c2b8651
[2.0.x] Update LPC176x tests, fix clean script ( #11617 )
6 years ago
a317bb4991
Remove stray tab
6 years ago
acf5ae3083
!ENABLED => DISABLED
6 years ago
ba1919c1eb
HAL tweaks to LPC1768 main
6 years ago
0987ed2a18
Use American English
6 years ago
6483285bc5
HOTEND_OFFSET_Z always available ( #11603 )
6 years ago
f8c52c9c29
Azteeg X5 Mini WiFi support ( #11601 )
6 years ago
3671c63cde
Einsy Full Graphic LCD Fix ( #11604 )
...
Fixed issue with LCD timings for Einsy RAMBo board.
6 years ago
593d5375ea
Fix G28 resetting DUAL_NOZZLE_DUPLICATION_MODE ( #11605 )
...
There's no reason for G28 to reset DUAL_NOZZLE_DUPLICATION_MODE, because it only affects the E stepper, unlike DUAL_X_CARRIAGE which affects the X steppers as well.
6 years ago
f0dbe61692
Tweaks to motion.h reachable tests
6 years ago
2d3317a35b
Prettify Dual X Carriage description
6 years ago
cd9868f442
Make position_is_reachable() smarter about IDEX machines`
...
On many IDEX machines the allowed travel of the X1 carraige and X2 carraige does not perfectly overlap.
This helps the issue. But more work needs to be done at the higher level. (For example the X1_MAX_POS should probably be factored into G26's mesh validation pattern.)
6 years ago
97f6396b25
Fix RE_ARM LCD pins to avoid #undef
6 years ago
0e25f66c09
Fix Ultimaker servo pin
...
As pointed out at https://github.com/MarlinFirmware/Marlin/issues/7981#issuecomment-407116642
6 years ago
ad12b9b46b
Fix indentation, whitespace, spelling, formbot pins...
6 years ago
b5537dde7f
need to add E2END to pins_RAMPS_FD_V2.h ( #11564 )
6 years ago
8f0bbdcc9b
Fix up Max7219 orientations ( #11596 )
6 years ago
a77f8c6dd5
Implement servo support for STM32F1 ( #11580 )
...
Implement servo support for STM32F1. Original code was incomplete and depended on Servo library from stm32duino which conflicts with `module/servo.h`.
6 years ago
0456caf0ad
Consolidate shared HALs and isolate HAL compile ( #11552 )
6 years ago
dfe18ac633
Fix compilation error for STM32F1 with U8GLIB_SSD1306 or U8GLIB_SH1106 enabled ( #11583 )
...
The `binary.h` file required by `lcd/dogm/dogm_bitmaps.h` is not present in stm32duino environment. Binary macros are defined in `bit_constants.h` in stm32duino framework.
6 years ago
b0a8ce59bd
Update Boards.h to include Formbot support
6 years ago
62ce937540
Update pins.h to include the Formbot board
6 years ago
a82be36d5d
Create pins_FORMBOT.h
6 years ago
00d24a8219
Don't call __delay_4cycles for 0 cycle delay - takes a really long time. ( #11586 )
6 years ago
56f1e17a25
[2.0.x] Max7219 cleanup, simplify, and extend ( #11575 )
6 years ago
0b2d686160
Fix "SD init fail" problem for STM32F1 ( #11579 )
...
Fix "SD init fail" problem for STM32F1 caused by incorrect SS pin state and incorrect SPI mode. Issue #11225
6 years ago
a98f21ec5e
Marlin assumes signed chars
6 years ago
db30650731
Fix UBL/Homing ( #11566 )
6 years ago
aae4c67e5d
Max7219 Clean Up ( #11563 )
...
Some of the Rotations did not do the right thing with setting and clearing pixels.
I think it is correct now. But if not... It is much closer to being correct.
6 years ago
9de730b2bf
Update tool_change.cpp ( #11559 )
6 years ago
c2553f9888
2.0.x - Idex match119 ( #11556 )
...
* Update ubl_G29.cpp
* Update ultralcd.cpp
6 years ago
e9de321ac0
declare void Max7219_register_setup();
6 years ago
952a1bc9d5
Merge pull request #11551 from thinkyhead/bf2_trinamic_fixes
...
[2.0.x] Fix TMC2208 SW serial communication
6 years ago
67613bf5bd
Update Czech translations ( #11510 )
6 years ago
bd6d032628
Update default driver configuration
...
Co-Authored-By: teemuatlut <teemu.mantykallio@live.fi>
6 years ago
1561e61df7
New TMC2208 constructor
...
Co-Authored-By: teemuatlut <teemu.mantykallio@live.fi>
6 years ago
b37bfeffeb
[2.0.x] Use the new const functions of the persistentStore api ( #11544 )
6 years ago
5573ef62c6
[2.0.x] PersistentStore update followup ( #11549 )
6 years ago
846bd24eb9
MALYAN_LCD is ok without SD
6 years ago
834ea7fcea
Remove 'const' from PersistentStore::capacity
6 years ago
c64199941e
Compile only selected PIO environment ( #11519 )
6 years ago
5be2559eda
Use flash memory to emulate EEPROM ( #11500 )
...
Use a sector of the LPC flash memory to emulate EEPROM storage, removing the need to have an SD card to store system parameters.
6 years ago
6964e1a95a
Clean up trailing whitespace
6 years ago
865ee5985f
Followup persistent store with heading, const
6 years ago
a4b0148365
Easier to find 'static inline'
6 years ago
cc0a60453f
Merge pull request #11526 from hasenbanck/eeprom-cleanup
...
[2.0.x] Change direct eeprom access to HAL::PersistentStore
6 years ago
65c5227c29
Change M7219 I to setup Max7219 registers, but not do initialization pattern
6 years ago
577aeb4aa9
All EEPROM access uses persistentStore
6 years ago
6a8b906318
Followup for persistent_store_api.h
6 years ago
66d2b48b59
Update PersistentStore api ( #11538 )
...
- Clean up the API to use a `static` class instance to adhere to Marlin convention
- Add `const` position data access for read/write
- Add Storage capacity to the interface
6 years ago
60f1376798
Make M7219 I more robust and nice to look at
...
Make M2719 initialize the Max7219 registers and then run the initialization pattern (if one is specified).
6 years ago
fd15b1495a
add I parameter to M42 to allow access to sensitive pins
6 years ago
11b411a872
Improve AXIS_DRIVER_TYPE macros
6 years ago
f1347f783d
Optimize thermistor table 71
...
agData in Table 71 is extremely oversampled (see Issue #11220 ). I have removed the data points that perform *worse* than linearly interpolating the remaining points, and fixed up two points that were simply rounded incorrectly.
Co-Authored-By: Aaron Griffith <aargri@gmail.com>
6 years ago
0bda22367b
Allow Einsy RAMBo FAN1_PIN override
6 years ago
1b921b246b
Fix pca9632_set_led_color
...
…when used with an I2C screen.
Co-Authored-By: soimy <soimy@163.com>
6 years ago
aa9d329560
Reduce max accel in Creality configs
6 years ago
c93538e9f3
UBL/planner patch tweaks
6 years ago
0af22549a6
Allow G33 to compile with no LCD
6 years ago
fc55f1da01
Account for UBL correction when setting the planner position ( #11486 )
6 years ago
b328fb4dc9
Treat TMC2660 like non-TMC ( #11508 )
6 years ago
72b086b90d
Add A5984 to example configurations
6 years ago
a1a5367380
Smoothieboard V1.0/1.1 and A5984 support
6 years ago
f891416e70
No raise on G28 after power-loss
6 years ago
e4ecade8d4
Fix AUTO_POWER_CONTROL compile error
...
Counterpart to #11467
Co-Authored-By: lsellens <lsellens@users.noreply.github.com>
6 years ago
eee1b7c50c
[2.0.x] Fix compile error ( #11465 )
...
Address #11463
6 years ago
e85feb2545
[2.0.x] Better timing handling ( #11461 )
6 years ago
79835590e3
Easier to disable homing validation ( #11458 )
6 years ago
131d216afa
Fix drivers.h dependency, defer macro evaluation ( #11450 )
7 years ago
9c62c47579
[2.0.x] Fix Dual X Carriage tool change crash ( #11447 )
7 years ago
9bae413901
Add Bigtreetech/BIQU KFB 2.0 board ( #11446 )
7 years ago
f2224755ad
Fix jumping progress bar. ( #11439 )
...
- When LCD_SET_PROGRESS_MANUALLY was disabled and an SD print was not active (i.e. the printer was idle), progress_bar_percent would read uninitialized memory from stack and cause progress bar to jump wildly.
- Also updated conditions in `#ifdef` to match `ultralcd.cpp`
7 years ago
aae02827c0
Cosmetic pins changes
7 years ago
64c493ad82
MKS_12864_OLED code cleanup
7 years ago
b826bf4194
Fix initial safe_speed in jerk code ( #11417 )
7 years ago
2cc950d67e
[2.0.x] MKS SBASE Trinamic examples/support ( #11402 )
7 years ago
16432376ab
Revert "[2.0.x]Idex and bl touch fixes" ( #11407 )
...
* Revert "[2.0.x] bltouch home refinements (#11397 )"
This reverts commit 74900f7a70#11395 )"
This reverts commit 6dafb90c01
7 years ago
74900f7a70
[2.0.x] bltouch home refinements ( #11397 )
...
Just create a better functions call logic flow
7 years ago
6dafb90c01
[2.0.x]Idex and bl touch fixes ( #11395 )
...
* Fix BLTouch homing
Deploy at start, dont call generic stow function at finish or raise goes too high before setting 0
* Update tool_change.cpp
* Update motion.cpp
* Update motion.cpp
* Update motion.cpp
* Update motion.cpp
* Change brackets to be more in align of Marlin coding standards
7 years ago
5ce5ff8e9b
[2.0.x] fix bltouch homing ( #11379 )
...
Partially revert. Seems to solve the issue, but one report says G29 still fails.
7 years ago
15d68cb496
Pre-override of ST7920 delays before HAL.h
7 years ago
8a24ff94d1
AT90USB1286 PIO cleanup and optimization ( #11230 )
...
-normalize `env` and `board` to lowercase naming convention.
-make board `name` follow descriptive convention.
-implement `-fsingle-precision-constant` compile optimization per https://github.com/MarlinFirmware/Marlin/pull/11178#issuecomment-401673901
-fix typo in 5DPRINT entry.
7 years ago
094e6d81a5
Add Einstart-S support ( #11219 )
...
Indeed the HAL does not need to be mucked around with to expose ATmega2560 pins not available as numbers on the MEGA board, I'll need to update the wiki with that tidbit and a reference to the pin-mapping comment in `fastio_1280.h`.
7 years ago
244b9a8257
Better fastio 1280/2560 pin list
...
Co-Authored-By: bleughb <36889022+bleughb@users.noreply.github.com>
7 years ago
955a7f0ae9
Improve driver.h macros ( #11371 )
7 years ago
aadcf08913
[2.0.x] add Calibrate Z (M915) to Prepare Menu ( #11331 )
7 years ago
4237c3d9f8
[2.0.x] different bltouch init ( #11135 )
7 years ago
624986d423
Ensure ADC conversion is complete before reading ( #11336 )
...
The current Marlin implementation relies on a timer interrupt to start the ADC conversion and read it. However in some circumstances the interrupt can be delayed resulting in insufficient time being available for the ADC conversion. This results in a bad reading and false temperature fluctuations. These changes make sure that the conversion is complete (by checking the ADC hardware via the HAL) before reading a value.
See: https://github.com/MarlinFirmware/Marlin/issues/11323
7 years ago
e2aa635e70
Fix Anet A6 thermistors
...
Co-Authored-By: vitekn <vitekn@users.noreply.github.com>
7 years ago
67b205fd45
Add support for board RuRAMPS4D v1.3 ( #11363 )
7 years ago
d1c6687ecd
Update MKS sBase pins ( #11357 )
7 years ago
048dbf6eca
Merge pull request #11275 from thinkyhead/bf2_pwm_adjustments
...
[2.0.x] Tweak some SoftPWM code
7 years ago
e05e95cf97
Clean trailing whitespace
7 years ago
22ebbc091f
Tweak some SoftPWM code
7 years ago
32de09f5c5
Specify some extra CR-10S pins
7 years ago
9c2bfa2ab3
Remove extra parameter to enqueue. ( #11364 )
7 years ago
bd3ec66a78
[2.0.x] typo fix ( #11365 )
...
Typo fix
7 years ago
fbcdf5eaeb
Simplify stepper driver per-axis selection
7 years ago
e5c0b490c8
Add *_DRIVER_TYPE to example configs
...
Co-Authored-By: teemuatlut <teemu.mantykallio@live.fi>
7 years ago
fbdbe53290
Fix get_period_inverse(0) so it doesn't crash ( #11334 )
7 years ago
14e2b11195
Fix spelling in configs
7 years ago
4685c7d59f
Followup to M91x I patch
7 years ago
62fa028155
Handle dual gantry machines better
7 years ago
09485f63e9
add missing ')'
7 years ago
a35abce1ac
Fix missing ')'
7 years ago
76d4cfb064
Tweak some Max7219 code
7 years ago
4195757585
Merge pull request #11309 from thinkyhead/bf2_manual_probe_start_z
...
[2.0.x] Manual Z Start Height
7 years ago
03b01e2500
Folger Tech i3-2020 now defaults to 2 Max7219 units
7 years ago
db85ca93c4
Change Max7219_idle_task() to use a column instead of row if Y-Axis as 16 LED's
7 years ago
9660996cc3
Add Multi Unit Support for Max7219 to bugfix_2.0.0 ( #11285 )
...
* Add Multi Unit Support for Max7219 to bugfix_2.0.0
* Apply multi-MAX7219 to example configs
* Tweak some spacing, macros
7 years ago
39c8aed8ba
Add MANUAL_PROBE_START_Z to example configs
7 years ago
2106fa26b1
Add MANUAL_PROBE_START_Z for manual probing
7 years ago
17ed0f815c
Fix tool_change call in UBL G29
...
Fix #11279 , #11252
7 years ago
6d2aff03bd
Merge pull request #11306 from thinkyhead/bf2_power_loss_pin
...
[2.0.x] Add support for power loss detect pin
7 years ago
63a146d424
planner.synchronize at start of tool_change
...
See https://github.com/MarlinFirmware/Marlin/issues/10949#issuecomment-398540498
7 years ago
665ac1e4d0
Add POWER_LOSS_PIN support
7 years ago
2243f72523
Add POWER_LOSS_PIN to example configs
7 years ago
47d5fcbbcc
[2.0.x] Change MKS SBASE default serial port to avoid confusion ( #11301 )
7 years ago
c83109c0ae
Merge pull request #11238 from xC0000005/MalyanLCDUpdate
...
[2.0.x] Malyan LCD Feedrate + Better Temp Handling
7 years ago
64f007580b
Fix some header comments
7 years ago
aed1d17a2d
Initialize default units ( #11295 )
...
When `INCH_MODE_SUPPORT` is enabled no default unit is set. This fixes it.
7 years ago
8c40f0c6c7
Reduce TQ message code size
7 years ago
b04e0c0cbb
Malyan LCD feedrate, better temp handling.
7 years ago
065e9c3d66
Add card.longest_filename method
7 years ago
71df1f7f57
Don't display M421 information for UBL at startup
...
It takes too long to display the mesh data for large mesh's at startup. We should consider ways to speed this up.
Perhaps it makes sense to display an entire row of the mesh instead of just one mesh point?
7 years ago
be7d1dfb3c
Merge pull request #11267 from teemuatlut/bf2_lpc_spi
...
[2.0.x] LPC1768: Expand hardware SPI class
7 years ago
8f686aa449
[2.0.x] Fix change filament crash ( #11269 )
...
Prevent crash, on filament change, when printer is not homed
7 years ago
f38c81cdde
LPC176x: Expand HW SPI class
7 years ago
3b5dec4b13
Add new LPC include folder
7 years ago
e486326910
Vellemann K8400 Y bed size is 180
...
Co-Authored-By: kaimimue <kaimimue@users.noreply.github.com>
7 years ago
e5ea9d200f
[2.0.x] fix kill printer ( #11260 )
...
This will fix kill message on dual printer with 0 alignment offset
7 years ago
8c57cadbe7
Include stdlib in fontutils ( #11251 )
...
When `REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER` is defined and Re-ARM build is attempted, `u8g_fontutf8.cpp` includes `fontutils.h` which uses `abs()`.
However, `abs()` is defined in `stdlib.h` which is not included in `fontutils.h`, so compile fails with an error.
Include `stdlib.h` in `fontutils.h` so that `abs()` is defined before `u8g_fontutf8.cpp` needs to use it, resolving the compile error.
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
7 years ago
bf7d0ba859
Assert that XY probe offsets are integers
7 years ago
12854f1909
Add Z_CLEARANCE_MULTI_PROBE to example configs
...
Co-Authored-By: nightgryphon <ngryph@gmail.com>
7 years ago
25e2ca8896
Add Z_CLEARANCE_MULTI_PROBE
...
Co-Authored-By: nightgryphon <ngryph@gmail.com>
7 years ago
fd8a76493b
Unify M91x parameter I meaning, simplify reports ( #11249 )
7 years ago
566d05006d
report_state > event_handler
...
Make the endstop report method track endstop changes on its own.
7 years ago
6b521b6df2
Loosen thermistor table size limit
...
Co-Authored-By: Aaron Griffith <aargri@gmail.com>
7 years ago
20761b88e0
Merge pull request #11212 from AlexanderAmelkin/2.0-HD44780-remove-unused-include
...
[2.0.x][HD44780] Remove unused include
7 years ago
603e136e87
Resolve issue where user can't edit UBL's mesh
7 years ago
ed720194d2
[2.0.x][HD44780] Remove unused include
...
The <binary.h> header is not available in STM32 toolchain
and is not used anywhere in ultralcd_common_HD44780.h.
If it is used anywhere in HD44780 support for other platforms,
it must be included in the corresponding .cpp file directly
and put under appropriate conditional compilation directives
for the platform requiring it.
As I was unable to find such code, I consider the file unused
and hence remove the inclusion.
7 years ago
d05e832f29
Add STM32F1 support for SD-based EEPROM
7 years ago
63f4c9bdb9
Followup to float maths patch
7 years ago
2992112da0
Optimize delta kinematics
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
1367df2875
Replace double with float, optimize calculation
7 years ago
d960d448fa
Optimize calculations with LROUND
7 years ago
68e6650df7
Remove Quake Fast Inverse SQRT (it isn't faster)
7 years ago
e7e896e7d7
More tweaks to fastio_Due.h
7 years ago
55f4744e54
[LPC176x] Endstop Interrupts Feature ( #11202 )
...
Enable the endstop interrupts feature for LPC176x boards. Although Smoothieboard chose to use non-interrupt capable pins for their endstops, and this has been copied by clones, so they can't use it.
7 years ago
5abf5bc8a7
[LPC176x] Fix Interrupt forward declarations ( #11200 )
7 years ago
cbea385ed7
[2.0.x] Fix LCD_LANGUAGE options list formatting in config ( #11198 )
...
* Fix LCD_LANGUAGE options list formatting in config
* Remove 'cn' language option from list
7 years ago
6837252fba
Merge pull request #11196 from thinkyhead/bf2_fix_m914_sgt
...
[2.0.x] No M914 or SGT with non-sensorless axes
7 years ago
5379c115c8
Fix Trigorilla include typo
7 years ago
9c058091e9
No M914 or SGT set for non-sensorless axes
7 years ago
c7ec6c68e7
Patch SCARA config to match 1.1.x
7 years ago
480a3d3d0c
Apply sensorless homing requirements only for specified axes
7 years ago
47ee149dfd
Merge pull request #11195 from thinkyhead/bf2_tronxy_x3a
...
[2.0.x] Tronxy X3A configurations and thermistor
7 years ago
8c0ec81a19
Followup to #11187
7 years ago
48c1f32b3e
Add configurations for Tronxy X3A
7 years ago
568cfe7caa
Add thermistor 501 (100K Zonestar)
7 years ago
1a0f4dedad
Fix and improve POWER_LOSS_RECOVERY ( #11187 )
7 years ago
e0ab8acf19
Add "Marlin Dev Mode" option
7 years ago
4b2af6ab48
Minor patches to POWER_LOSS_RECOVERY
7 years ago
1ea222e6fc
Turn off DISABLE_INACTIVE_EXTRUDER with SWITCHING_NOZZLE
...
Fix #11183
7 years ago
8299ac121d
[2.0.x] Slovak translation update ( #11175 )
7 years ago
3de0c85d41
Fix RRW graphical LCD constructor macro ( #11171 )
7 years ago
cedc158106
[2.0.x] Board specific init macro ( #11170 )
7 years ago
5616581eb1
[LPC176x] Update fastio _GET_INPUT, _GET_OUTPUT macros ( #11168 )
7 years ago
8a8eae8d97
Implement more fastio_Due macros ( #11165 )
7 years ago
c51e27d11d
Do a hard kill for failed homing moves ( #11161 )
7 years ago
90ba77ea0f
Lose the old HOMEAXIS macro
7 years ago
2421f3a47d
Detect endstop hits in any direction
7 years ago
f9a090b2cf
Fix Trigorilla 1.4 pins
...
See #11097
7 years ago
8eaac0dab3
Add delta feedrate scaling ( #11153 )
7 years ago
444725ae9a
Non-conflicting CS pins for MKS Gen L
7 years ago
8c9f90153e
Enable Malyan LCD Support for M200 printers. ( #11051 )
7 years ago
fc10101b06
Tweaks to fastio_Due.h
7 years ago
05518d6add
Add newline to end of file
7 years ago
d4fde91222
Fix serial.h including itself
7 years ago
a431013eb7
Fix G33 compile warning
7 years ago
bd7f5848f1
Remove JUNCTION_DEVIATION_INCLUDE_E option ( #11147 )
7 years ago
fbf1c9b496
Fix and tweak POWER_LOSS_RECOVERY ( #11151 )
7 years ago
0fff79c24b
Fixes G29_with_retry behavior ( #11045 )
...
* Fix G29 (ABL) retry behavior
7 years ago
3349eb0020
Fix SKEW_CORRECTION compile error
7 years ago
a264030526
Fix "G29" G29_MAX_RETRIES handling
7 years ago
42f9921482
Ignore Z min endstop with separate Z-probe
...
To allow for the case where a Z endstop (e.g., hall effect) is higher than the probe trigger point, don't check the Z min endstop during probe moves. See #11134
7 years ago
1b8973eb1c
Fix up microsteps conditionals
7 years ago
aa4cd2e861
Eliminate stepper.* signed/unsigned warnings
7 years ago
edb21f349a
Fix stepper/planner block handling, race conditions ( #11098 )
...
- Allow planner to alter the deceleration phase of the currently executing block.
- Remove BUSY flag, as it is NON ATOMIC to set bits in the Stepper ISR and Planner at the same time.
7 years ago
4d3a9930c5
Match ASM comment spacing to 1.1.x
7 years ago
Scott Lahteine