81edbfa665
Merge pull request #11004 from ejtagle/always_honor_maximum_step_rate
...
[2.0.x] Fix stepper pulse minimum period and timing calculations
7 years ago
f3fed52348
Fix coolstep_min_speed / sensorless homing
...
Fix #8890
7 years ago
a215725df6
Fix stepper pulse timing
...
Always honor minimum period on stepper pulse generation, and fix timing calculations
Signed-off-by: etagle <ejtagle@hotmail.com>
7 years ago
0d79128c8d
Localize stepper-specific defines
7 years ago
4dbec774b5
HAL_*_TIMER_RATE => *_TIMER_RATE
7 years ago
9d04f47d98
Improvements for junction_deviation_mm
...
- Drop `max_jerk` with `JUNCTION_DEVIATION`
- Add `max_e_jerk_factor` for use by `LIN_ADVANCE`
- Recalculate `max_e_jerk_factor` when `junction_deviation_mm` changes
- Fix LCD editing of `junction_deviation_mm`
7 years ago
f2c3b0d476
Use bit flags for homed/known
7 years ago
43bdd0bfe4
Fix indent in stepper.h
7 years ago
3fd1f32b73
Fix ADC key and chamber temp
7 years ago
a2f521d34b
Add Junction Deviation mm runtime setting ( #10990 )
7 years ago
6f14bcaa3e
Add MAXIMUM_STEPPER_RATE, enforce in multi-stepping
...
The timing value should be properly set for ALL boards. The compiler will check and set maximum step rate calculations based on those values.
7 years ago
39a7e7720d
Adaptive multiaxis step smoothing
...
- Stepper bugs fixed
- Support MIXING_EXTRUDER with Linear Advance
- Miscellaneous cleanup
7 years ago
b64cc9329e
[2.0.x] Fix dual enstop home ( #10980 )
7 years ago
3701869e6c
Add HAL_timer_start for AVR, use stepper timer to time pulses
7 years ago
d82704354f
Increase the planner first block HOLD delay to 100mS
7 years ago
334341c632
Hephestos config updates ( #10960 )
7 years ago
55aedf036b
Fix M503 ABL mesh report. (Zero-based IJ indices)
7 years ago
d8b983f624
More concise M503 output for M906, M913, M914 ( #10947 )
7 years ago
ad8d3150aa
Cleanup for dual endstops homing
7 years ago
d3c02410a8
[2.0.x] Small assorted collection of fixes and improvements ( #10911 )
...
* Misc fixes and improvements
- Get rid of most critical sections on the Serial port drivers for AVR and DUE. Proper usage of FIFOs should allow interrupts to stay enabled without harm to queuing and dequeuing.
Also, with 8-bit indices (for AVR) and up to 32-bit indices (for ARM), there is no need to protect reads and writes to those indices.
- Simplify the XON/XOFF logic quite a bit. Much cleaner now (both for AVR and ARM)
- Prevent a race condition (edge case) that could happen when estimating the proper value for the stepper timer (by reading it) and writing the calculated value for the time to the next ISR by disabling interrupts in those critical and small sections of the code - The problem could lead to lost steps.
- Fix dual endstops not properly homing bug (maybe).
* Set position immediately when possible
7 years ago
2deff0d9b9
Fix/Improve junction deviation
...
- Respect axis max acceleration limits instead of forcing a fixed acceleration value.
- The `junction_unit_vec` ensures proper handling of entry and exit speeds even when the axes involved have different limits.
7 years ago
d259070980
Clean up trailing spaces from vim, etc.
7 years ago
b90f54b0fc
Improve probe logging
7 years ago
4299e5dc8b
Modify E-stepping macros for use in LINEAR_ADVANCE ( #10885 )
7 years ago
8f14ef855d
More concise commentary in planner.cpp
7 years ago
6919e87656
Minor cleanup of multi-stepping logic
7 years ago
853a9056ac
Long thermistor tables need special consideration
7 years ago
a4f9c3373f
Tweak thermistor spacing
7 years ago
1ce97f1f6d
Faster (bisect) search in thermistor tables ( #10883 )
7 years ago
0ca9db7051
Correct HOTENDS for SWITCHING_EXTRUDER
7 years ago
7b9f0302d4
Fix Bresenham rounding errors, add link to article ( #10871 )
7 years ago
2566342979
Adjust some commentary
7 years ago
6775a16c97
Fix switching extruder stepping with LA
7 years ago
931ab4ec40
Rename Junction Deviation options
7 years ago
aaaf09bda2
BEZIER_JERK_CONTROL => S_CURVE_ACCELERATION
7 years ago
01d37e00af
Fix up stepper ISR with linear advance timing ( #10853 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
7261f48872
Fix reset of endstops and move state
7 years ago
50fa8e01c1
Minor optimization of axis_did_move bits
7 years ago
f28e366b77
Followup for core endstops
7 years ago
9644d56b42
Patches for core motion tests
7 years ago
3e3789da85
Regression: Endstops Core compatibility ( #10823 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
4b610b333e
Tweak G38 formatting
7 years ago
d2647c1f19
Fix G1 behaviour after tool unpark
...
Fix #10777 for 2.0.x
Co-Authored-By: Ante Vukorepa <o.orcinus@gmail.com>
7 years ago
0c3773d724
Cleanup in stepper_indirection.h
7 years ago
4b2f6e3b2b
[2.0.x] Add endstop noise filter ( #10796 )
7 years ago
65a004564c
Stepper::set_position needed for some applications
7 years ago
435ecb6b67
Followup to stepper/planner refactor
7 years ago
d557c84a71
[2.0.x] Error for FAST_PWM_FAN with 32 bit CPU ( #10798 )
7 years ago
569df3fc0c
Fix interrupt-based endstop detection
...
- Also implemented real endstop reading on interrupt.
7 years ago
a4af975873
Fix planner block optimization
...
- Fixed the planner incorrectly avoiding optimization of the block following the active one.
- Added extra conditions to terminate planner early and avoid redundant computations.
7 years ago
e0ca627033
Planner block HOLD flag
...
Allows the Stepper ISR to wait until a given block is free for use. Allows Planner to plan the first move, which is split into two.
7 years ago
a11eb50a3e
Refactor and optimize Stepper/Planner
...
Better encapsulation and considerably reduce stepper jitter
7 years ago
0566badcef
Add memory barrier, optimal interrupt on-off
...
Disabling an ISR on ARM has 3 instructions of latency. A Memory barrier is REQUIRED to ensure proper and predictable disabling. Memory barriers are expensive, so avoid disabling if already disabled (See https://mcuoneclipse.com/2015/10/16/nvic-disabling-interrupts-on-arm-cortex-m-and-the-need-for-a-memory-barrier-instruction/ )
7 years ago
7dc03ce721
Simplified fix for babystep pulse width
...
Alternative to the apparently superfluous double delay
7 years ago
65270d6a96
Fix LIN_ADVANCE + SWITCHING_EXTRUDER
...
Followup to #10656
7 years ago
9ad42d6617
add delay between pulse edges ( #10778 )
7 years ago
83d42f33e1
Add HAS_HOTEND_OFFSET_Z conditional
7 years ago
3c76bda2d8
Fix switching extruder
...
`DONT_SWITCH` got lost along the way. Replace it with `DO_SWITCH_EXTRUDER` and adjust the code.
7 years ago
e1d9046efc
[2.0.x] Temperature reading fix ( #10774 )
7 years ago
50270b53a0
Clear up some more compile warnings
7 years ago
43ddb29f9e
Add FAN_MAX_PWM for M106-controlled fans
7 years ago
836b0bbeee
Fix MBL line_to_destination
...
Fix #10708
7 years ago
ba4c32eec5
Followup to _AXIS patch
7 years ago
d9154ebdf6
Followup to math patch
7 years ago
883b0c9880
Convert custom maths to inlines ( #10728 )
7 years ago
08e36e264e
Apply _AXIS macro
7 years ago
99ecdf59af
Smarter MIN, MAX, ABS macros
...
Use macros that explicitly avoid double-evaluation and can be used for any datatype, replacing `min`, `max`, `abs`, `fabs`, `labs`, and `FABS`.
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
083ec9963e
Tweaks to heater / lcd conditions
7 years ago
8f8c6a9bc4
Move get_axis_position_mm to Planner ( #10718 )
7 years ago
a1062eec5b
Better handling of DELAY_NS and DELAY_US ( #10716 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
f5aaa2d6c0
Fix some compiler warnings
7 years ago
3614e6ce0f
Fix Switching Extruder with Linear Advance
7 years ago
625035a9ce
Fix M301 access to lpq_len ( #10714 )
...
Co-Authored-By: Zwaubel
7 years ago
306f0f2135
Move Stepper::synchronize to Planner ( #10713 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
d99f1b2245
[2.0.x] EEPROM code cleanup ( #10710 )
7 years ago
325bbbc8c2
[2.0.x] Enable AD595 and AD8495 in concert ( #10693 )
...
* Allow both AD595 and AD8495 in concert
* General temperature code tweaks
7 years ago
23a876b08d
Update a comment in motion.cpp
7 years ago
439e0cdd0f
Patch up reverse_pass_kernel (and other planner code) ( #10674 )
7 years ago
57c2f8d2f6
Trailing whitespace cleanup
7 years ago
b76344c080
More Trinamic cleanup
7 years ago
722aba77f3
Fix LIN_ADVANCE + SWITCHING_EXTRUDER stepper directions ( #10656 )
7 years ago
a225d2e99e
Fix compilation with UBL and Arc/Bézier
...
Fix #10660
7 years ago
6d9ec1852a
Fix compilation of say_units
...
Fixes #10663
7 years ago
19f189b4e5
Add UBL support for G2/G3 and G5 ( #10648 )
7 years ago
4d4bf7897d
Junction Deviation jerk limiting option
7 years ago
0436e16fb2
Apply shorthand Assembler macros
7 years ago
d1b619be52
Standardize some hexadecimals
7 years ago
55f1f8446b
Show correct current units in M503
7 years ago
1f11b0f612
Fully init planner sync block
7 years ago
bfe223e120
Adjust usage of stepper.synchronize
7 years ago
af1950a63e
Improve sync of stepper positions
7 years ago
0c23792344
Apply int32_t to stepper
7 years ago
81b632c255
Additional temp-oriented improvements
7 years ago
e911635fb1
Add thermocouple with AD8495 support
7 years ago
d7b699ec34
Fewer includes of vector_3.h
7 years ago
2c1205d8b1
Improve debug of homing move feedrate
7 years ago
c8e4b7c8a6
Fix XY homing move away rate
7 years ago
1f92b9a4ed
Fix do_probe_move with fr_mm_s ( #10576 )
7 years ago
4dfc011d86
Fix homing with probe feedrates
7 years ago
59fda986ea
Allow Z_AFTER_PROBING to be 0
7 years ago
1dab44213a
Fix the TMC26X initializer CS pin argument
...
From #10531
Co-Authored-By: chriscg9 <chriscg9@users.noreply.github.com>
7 years ago
7546f87949
Allow a home bump of 0 when homing Z with probe
7 years ago
683dc24e0f
When homing with Z probe bump at Z_PROBE_SPEED_SLOW
7 years ago
5ac226aa93
Further cleanup of inline delays
7 years ago
2242b98248
[LPC176x] Emergency Parser Feature ( #10516 )
7 years ago
9789c1c719
Fix current_temperature_chamber compile error
...
Fix #10505
7 years ago
0c428a66d9
Proper AVR preemptive interrupt handling ( #10496 )
...
Also simplify logic on all ARM-based interrupts. Now, it is REQUIRED to properly configure interrupt priority. USART should have highest priority, followed by Stepper, and then all others.
7 years ago
f423e54f77
Strip trailing spaces
7 years ago
cb46cb8480
Add HAS_HEATED_BED conditional ( #10495 )
7 years ago
a90cbc6339
[2.0.x] Wait for bed heaters between probing ( #10472 )
7 years ago
5a064d0e94
Fix bug in planner.set_position_mm
7 years ago
8f57e098de
Use end-of-line comments in planner.cpp
7 years ago
36b97bde9f
clear_block_buffer, kill_current_block in quick_stop
7 years ago
12785583d0
[2.0.x] G33 MIN_STEPS_PER_SEGMENT ( #10386 )
7 years ago
646aa20b43
Overhaul of G33 Delta Calibration ( #8822 )
7 years ago
ac2e0afb62
Low Point for delta calibration ( #10363 )
7 years ago
57a899a412
[2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR ( #10373 )
7 years ago
2d9b0a66fe
Add Filament Change accelerations
7 years ago
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
7 years ago
a29adde5c0
Implement BEZIER_JERK_CONTROL
...
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
7 years ago
0e8242180d
Chamber temperature monitoring and auto fan control.
...
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
7 years ago
75037493fa
Default active low for TMC2130 DIAG1 ( #10294 )
...
- Added sanity check to inform users to set the endstop to inverting
when using SENSORLESS_HOMING
7 years ago
e8e60263c8
Scale feedrate (mm/s to deg/s) for SCARA
7 years ago
1c36606886
Fix MSG_HEATING_FAILED_LCD_BED macro evaluation
7 years ago
fe91514395
MBL should add z_offset regardless of fade ( #10308 )
7 years ago
8bc93c6f2b
Improve heating/cooling LCD messages ( #10293 )
7 years ago
21a47b50f4
Additional tool-change fixes ( #10304 )
...
Followup to #10257
7 years ago
7cbbc2af7a
[2.0.x] Optional heater signal inversion ( #10260 )
7 years ago
241996d5d6
Merge pull request #10257 from thinkyhead/bf2_tool_change_debug
7 years ago
4c79dc1093
Fix a Serial+EEPROM compile error
...
Fixes #10278
7 years ago
adcb87f0db
Z Endstop Servo => Z Probe Servo
7 years ago
02f0f95d40
Handle disabled HYBRID_THRESHOLD in EEPROM ( #10275 )
7 years ago
2672120a97
Do a small raise for all move-back
7 years ago
5acccbacc1
Simplified leveling-based tool change
7 years ago
d1734a089a
Split up tool_change for some setups
7 years ago
7d8a46519f
Output ABC for delta stepper counts
7 years ago
ac7e97f4fe
Change order of inactive stepper disable/enable
...
This ensures that steppers that share an enable pin will only be disabled for a miniscule time.
7 years ago
b6a55f0891
Temporary workaround for tool-change compile error
...
Pending a more complete solution to tool-change Z deviation.
7 years ago
b852781eba
Fix BLTOUCH compile error
...
Followup to #10250
7 years ago
8b7381b626
Clear sensorless homing in home_delta after first move-to-top
7 years ago
dbe2b6f7b0
Do moves towards endstops differently in do_homing_move
7 years ago
2bc7f416ee
Fix missing comma in tmc_sgt
...
Fixes #10209
7 years ago
9656a82609
Fix G53/CNC_COORDINATE_SYSTEMS compilation, Travis testing ( #10227 )
7 years ago
b287560258
Fix say_M603
7 years ago
a891af2f7a
Enforce minimum TMC2130 / TMC2208 libs
7 years ago
8870f9b1da
Fix M503 helper functions following TMC updates ( #10197 )
7 years ago
bb7236a750
Z correction on tool-change for all HAS_MESH ( #10199 )
7 years ago
9da0797e29
Fix EEPROM size of tmc_hybrid_threshold
...
Followup to #10102
7 years ago
1628a9e864
make data declarations consistent
7 years ago
1cb810ff1c
[2.0.x] Automatically reset stepper timeout ( #10179 )
...
* Automatically reset stepper timeout in manage_inactivity
Any code that adds moves to the planner can skip resetting the stepper timeout. We can let `idle` / `manage_inactivity` reset the timer whenever it detects any moves in the planner.
* blocks_queued => has_blocks_queued
7 years ago
97e8a6ebd9
Various fixes for DUE... ( #10152 )
...
- Watchdog reset during SD Card initialization.
- Move `DebugMonitor` to `DebugMonitor_Due.cpp`.
- Since the watchdog is enabled on boot do extra resets during init.
- Have `thermalManager` do watchdog reset before its ISR starts to prevent reset.
- Ensure that timers are stopped before reprogramming them to address tone issues.
- Improve SAM3XE reset when reflashed through the native port.
7 years ago
9fd1016bb1
Trust the bootloader to clear globals
7 years ago
bc45fb6b13
Tweak use of move_z_after_probing
7 years ago
c352954882
Allow no raise after run_z_probe in probe_pt
7 years ago
8dfaf1539e
Merge pull request #10102 from thinkyhead/bf2_eeprom_M913
...
[2.0.x] More complete Trinamic driver options
7 years ago
837ac2fdbd
[2.0.x] Fix_Autotune_THERMAL_PROTECTION_BED_off ( #10166 )
...
- Fix Autotune Thermal Protection
- Make 2 constants in autotune configurable
7 years ago
a5c6d3c7b8
Prevent null pointer crash in Endstops::update
...
Thanks to Evgeny Kotsuba!
7 years ago
a46bac3100
Add 'I' parameter to M906/M913/M914; 'T' to M906/M913
7 years ago
c95450016b
Improve Trinamic support in the EEPROM
7 years ago
48d7036874
Consolidate smart stepper driver initialization
7 years ago
eaefc1e410
Add CorePQ support for BABYSTEPPING ( #10155 )
7 years ago
772810fb24
Followup to PORTVAR patch
7 years ago
93af8aa157
Fix home_delta for SENSORLESS_HOMING ( #10145 )
7 years ago
c6ff39cc14
Spacing cleanup
7 years ago
a6feb58837
Delta support for multiple hotends with offsets ( #10118 )
7 years ago
1e946d681d
Update Marlin for newest TMC libraries
...
- TMC2130Stepper v2.2.0
- TMC2208Stepper v0.0.4
7 years ago
4aebe3d82e
Pretty up EEPROM port args
7 years ago
51bf3c9503
Fix E direction for MK2_MULTIPLEXER with LIN_ADVANCE
7 years ago
e7a61de8af
[2.0] FWRetract Reset (Best way) ( #10083 )
7 years ago
e7570f3195
Improve TMC config organization, naming
7 years ago
07cf2cd9c4
Fix sensorless_homing_per_axis compile warning
7 years ago
14c03cb6f4
[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) ( #10069 )
...
Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.
7 years ago
468f34104b
Patch do_blocking_move_to so 'destination' can be used
7 years ago
28f1276286
[2.0.x] Add Z_AFTER_PROBING option ( #10058 )
...
Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.
7 years ago
751785fc97
Followup to recent patches
...
- `M666` is static, not inline
- Disambiguate some stepper macros
7 years ago
a0211f5d6c
Disambiguate else in stepper_indirection.h
7 years ago
f10c87b442
Update Endstops class for 1.1.x parity
7 years ago
239902f861
Fix E2END and add EEPROM to Smart RAMPS
...
Reference #9983
7 years ago
419d12ca1b
Add UNKNOWN_Z_NO_RAISE option
...
With this option enabled, Z won't ever be raised until after `G28` has been completed, and it won't raise if Z becomes unknown. This is good for machines whose beds fall when Z is powered off.
7 years ago
3b4c89e4b5
Move do_probe_raise closer to set_probe_deployed
...
…and limit the raise to Z_MAX_POS
7 years ago
2908e76151
Fix position_is_reachable_by_probe typo, add comment
...
Fix #10029
7 years ago
161ff9ff35
Fix UPDATE_ENDSTOP for CorePQ compatibility
...
Fixes #9939
7 years ago
49ca67202f
Patch configuration_store for extra serial port
...
Fix #9948
7 years ago
16a8edc5f0
Add more delay before pulse off in Linear Advance ISR
...
A capital idea from https://github.com/MarlinFirmware/Marlin/pull/9914#issuecomment-371614153
7 years ago
dfd5d2fe75
Have position_is_reachable_by_probe use the whole bed ( #10020 )
...
Previously `position_is_reachable_by_probe` was limited to the area specified for `G29` mesh leveling (even if leveling was disabled). This change will properly consider the entire bed area so that `G30` and other non-leveling probing may take place.
7 years ago
3c2bfa5e53
Update powersupply_on in power_on/off ( #10015 )
...
Fix #10004
7 years ago
8d32fd997f
Wrap NORM_E_DIR/REV_E_DIR macros in do{}while(0)
7 years ago
98d48fc731
Followup to HAL_timer_restrain
...
Followup to #9985
7 years ago
a1a88ebabc
HAL function to ensure min stepper interrupt interval ( #9985 )
7 years ago
9515e5aefb
Fix LA_active_extruder (static)
7 years ago
e5ec793f7e
Wrap stepper indirection macros
7 years ago
5b85464791
Fix for LA ( #9964 )
...
Missed in the original LA 1.5 PR: eISR has to use a local copy of
current_block->use_advance_lead because it might still run wenn the last
block has been set to NULL.
7 years ago
ffbf63e6af
Add HAS_TEMP_SENSOR conditional
7 years ago
2057177184
Make enums into implicit char
7 years ago
ca0def766e
LIN_ADVANCE single stepper optimization
7 years ago
8291ae34f2
Support duplication mode in LIN_ADVANCE
7 years ago
0dd1c4458d
Put more code between pulse start and stop ( #9959 )
7 years ago
36262a0479
Use static classes for job timers ( #9938 )
7 years ago
930720bbbb
Fix broken reverse planner ( #9943 )
...
From #9914 by @Sebastianv650
7 years ago
025118da3e
Init print_job_timer in setup() instead of "early" ( #9937 )
7 years ago
07ae23fe14
No pulse delay on last e_steps in advance isr
7 years ago
ed758de80d
tweak comment in stepper.cpp
7 years ago
d1dc863962
autotemp_factor is not value_celsius_diff
...
See https://github.com/MarlinFirmware/Marlin/issues/9852#issuecomment-369861822
7 years ago
f3914a432e
Clear retracted status when homing the Z axis
7 years ago
6d7f4f84e2
Add board MKS_BASE_HEROIC ( #9926 )
...
Followup to #9008
- Don't define micro-stepping pins for boards that lack them.
- Allow setting of 128 microsteps with `M350`.
7 years ago
649f375494
Fix: M112 calling kill from interrupt ( #9923 )
...
Fix #9906
7 years ago
23a576faf7
[2.0] Fix for FW retract ( #9878 )
7 years ago
91db7930dc
Drop SCARA_FEEDRATE_SCALING
...
The updated planner takes the length of the move, so this pre-calculation is no longer needed.
7 years ago
1746749361
Followup to #9868
7 years ago
a446433c87
Fix SENSORLESS_HOMING for Core Kinematics ( #9868 )
7 years ago
c22f8dd660
Get duration_t in printcounter.h for its clients ( #9843 )
7 years ago
966d9af98a
Mesh export in Bilinear + UBL M503
7 years ago
8d5a77001e
EEPROM parity with 1.1.x
7 years ago
cb4cb86d80
Useless line removed ( #9814 )
...
nextAdvanceISR is set in the next if structure in every possible
situation, so it's useless to set it once more before.
7 years ago
0557ab5780
Fix CONFIG_ECHO_START bug
...
In reference to #9633
7 years ago
813f9f3082
[bugfix_2.0.x] - LIN_ADVANCE V1.5 stepper.cpp ( #9797 )
...
Removal of obsolete (i) from port of LIN_ADVANCE from V1.1.x to V2..0.x.
7 years ago
3f89bbeab5
Drop a conditional only used once
7 years ago
689bc99402
Correction to acceleration
7 years ago
2bd252b501
[2.0.x] LIN_ADVANCE v1.5 ( #9712 )
7 years ago
2c9775313a
Fix Z position on HD44780
...
Fix #9732
7 years ago
5968a3e60e
Add ADVANCED_PAUSE_FEATURE include
7 years ago
73cd34b121
Finish AUTO_POWER_CONTROL implementation
...
Followup to #9503
7 years ago
b3deadd898
Don't raise FIX_MOUNTED_PROBE on stow
...
Reference #9336
7 years ago
3d1692d1fd
Fix X2 enable with X_DUAL_STEPPER_DRIVERS
...
From #9286
7 years ago
c241da32e8
stepper.h parity with 1.1.x
7 years ago
ca55f2927a
Pulldown pin mode support ( #9701 )
...
Implemented for LPC1768.
7 years ago
83d7e95de0
Add MSG_THERMAL_RUNAWAY_BED ( #9691 )
7 years ago
472229b974
Fix #9681
7 years ago
03d790451f
[2.0.x] HAL timer set/get count => set/get compare ( #9581 )
...
To reduce confusion over the current timer count vs. the compare (aka "top") value. Caution: this re-uses the function name, changing its meaning.
7 years ago
7280fa1e31
Patch Power class
7 years ago
e698998343
More reliable PROBING_HEATERS_OFF with BED_LIMIT_SWITCHING
7 years ago
1541224a81
Enable Z axis and delta sensorless homing ( #9516 )
7 years ago
d168ee9bed
Drop leveling include from steppers.cpp
7 years ago
b5e92f4f90
[2.0.x] Enable / disable PSU automatically ( #9503 )
7 years ago
ac6bf7226a
Update of comments in thermistor files. No functional changes. ( #8986 )
7 years ago
786746404b
[2.0.x] Apply feedrate to nozzle movement for kinematic machines ( #8778 )
7 years ago
e1fd9c08b3
[2.0.x] Add support for LPC1769 at 120 MHz ( #9423 )
7 years ago
9b9350e010
Fix jerky Z motion between probes
...
Suggested by #9375
7 years ago
ea9ad4e46d
[2.0.x] Fix compile error on delta when NO_WORKSPACE_OFFSETS ( #9388 )
7 years ago
c251601916
Simplified SET_BIT, moved to endstops.cpp
7 years ago
f8227abf1c
Merge pull request #9384 from tcm0116/2.0.x-retract
...
[2.0.x] Clear retracted status when homing the Z axis
7 years ago
5c69d45f5b
[2.0.x] TMC2130 support for LPC platform ( #9114 )
7 years ago
7035471982
Clear retracted status when homing the Z axis
7 years ago
2bea1bda56
Move more strings to PROGMEM
7 years ago
1dcfe193ac
Optimize some serial strings
7 years ago
9644fe1839
Lightly optimize arc length calculation
7 years ago
3217da6fa5
Followup patch for TMC stepper init
7 years ago
db031d5d76
Add missing SoftwareSerial begin for TMC2208
...
Based on #9299
7 years ago
f7f8569bbf
Fix skew settings report precision
...
Followup to changes from #8843
7 years ago
205c5fa078
Merge pull request #9277 from oysteinkrog/fix/DualX_Endstops
...
[2.0.x] Fix DUAL_X_CARRIAGE endstop tests
7 years ago
Scott Lahteine