eef0248a1c
Add M420 C to adjust the whole mesh ( #10522 )
7 years ago
c1e5ebbc1e
[2.0.x] AVR: Atomic bit set and clear of upper pin ports without critical section ( #10502 )
...
* AVR: Atomic bit set and clear
The critical section can be dropped, saving 3 cycles per access. Also simplified pin toggling for all ports.
7 years ago
02a711c4d6
[2.0.x] Fix crash upon repeated calls to process_subcommands_now_P ( #10509 )
7 years ago
a3ce8a3fcd
Add sanity checks for EMERGENCY_PARSER
7 years ago
f06c3c38b9
Fix M0_M1 with no LCD
7 years ago
c82dd5129f
Revert potentially-not-redundant UBL test
...
Response to #10435
7 years ago
9789c1c719
Fix current_temperature_chamber compile error
...
Fix #10505
7 years ago
0c428a66d9
Proper AVR preemptive interrupt handling ( #10496 )
...
Also simplify logic on all ARM-based interrupts. Now, it is REQUIRED to properly configure interrupt priority. USART should have highest priority, followed by Stepper, and then all others.
7 years ago
f423e54f77
Strip trailing spaces
7 years ago
8177c4334e
Merge pull request #10498 from xC0000005/MalyanLCDFix
...
Fix overridden Malyan LCD functions
7 years ago
cb46cb8480
Add HAS_HEATED_BED conditional ( #10495 )
7 years ago
10a25f733e
Add SENSORLESS_HOMING to Archim 2.0 ( #10500 )
7 years ago
24d23ce49b
Fix function definitions for Malyan LCD
7 years ago
ad58b626a3
Fix pin mappings for Viki2 on Azteeg X5 GT ( #10487 )
7 years ago
9e07df5c1b
Extra options for LEVEL_BED_CORNERS ( #10483 )
7 years ago
1c3d49afe0
Fix G28 with Z_AFTER_PROBING
...
Fix #10476
7 years ago
b6747c742a
Cleanup AZTEEG_X5_GT pins for VIKI
...
What should the SD detect and SDSS pins be? Followup soon on #8138
7 years ago
023385ca59
Merge pull request #10479 from thinkyhead/bf2_creality_power_loss_resume
...
[2.0.x] Creality3D Power-Loss Recovery
7 years ago
3396671011
[2.0.x] Reset LCD status to fallbacks ( #10470 )
...
* Remove obsolete strings
* Tweak some static consts
* Reset LCD status to fallbacks
7 years ago
d58450c82a
Russian language update
...
Co-Authored-By: anton-piliugin <34044202+anton-piliugin@users.noreply.github.com>
7 years ago
11ab017dd0
Creality3D Power-Loss Recovery
7 years ago
594d6f9efd
Add POWER_LOSS_RECOVERY to example configs
7 years ago
7dcd0a1cff
Add R parameter to G28 to specify pre-raise
7 years ago
2f4b4d6076
Add Stopwatch::resume method
7 years ago
a90cbc6339
[2.0.x] Wait for bed heaters between probing ( #10472 )
7 years ago
a0dac95d25
Merge pull request #10460 from thinkyhead/bf2_trigorilla_14
...
[2.0.x] Split TRIGORILLA into 1.3 and 1.4
7 years ago
f0cbf3d432
Correction to sanity check
7 years ago
d8a8eec6ea
Add THERMAL_PROTECTION capability
...
Based on #10465
In response to `M115` the firmware reports if Thermal Protection is enabled (1) or not (0). This information can be used by software such as OctoPrint (more precisely the Printer Safety Check plugin) to warn users when Thermal Protection is not enabled in the firmware.
Co-Authored-By: andrivet <sebastien@advtools.com>
7 years ago
186d71b361
Complete CREALITY_ENDER revert
7 years ago
11ef432476
Match Makefile to boards.h
7 years ago
2be5fe5ddf
Split TRIGORILLA into 1.3 and 1.4
7 years ago
80e29492c6
TRIGORILLA => TRIGORILLA_13
7 years ago
dea686cf55
Define short pin names in fastio for STM32 ( #10461 )
7 years ago
65a6a86d19
Don't report point 0 in MBL G29
7 years ago
6faa93d787
Add G29_RETRY_AND_RECOVER to example configs
7 years ago
5cc7916e69
Add G29_RETRY_AND_RECOVER feature
...
- Add an option to retry G29, optionally executing a G-code procedure after each failed probe.
7 years ago
78ea4871f9
Fix up enqueue now functions
...
…and apply to MALYAN_LCD.
7 years ago
23635c2b64
Update ubl_motion.cpp
...
Restore necessary and needed loop termination logic.
7 years ago
8ca3c43d73
Updated language_data spacing, headers
7 years ago
184c077c58
Correct includes (u8g.h) and spelling
7 years ago
627348b46c
move the TALL_FONT_CORRECTION to language files
7 years ago
77bc653524
Use X windows 6x12 bitmap font to support western languages.
7 years ago
d81649b365
Update language data for sk.
7 years ago
41839746a2
Removed unused macros
7 years ago
4f184ba5da
[2.0.x] Add BOARD_MKS_BASE_15 with digital micro-stepping ( #10454 )
...
* Add BOARD_MKS_BASE_15 with digital micro-stepping
* Rename MKS_13 to MKS_GEN_13
7 years ago
ad6baa5c9d
Fix for UBL set_bed_leveling_enabled
7 years ago
df2f24617b
Use 0 as the bed position (not Z_MIN_POS)
7 years ago
428c54f2ad
[2.0.x] HAL for STM32F4 ( #10434 )
7 years ago
744bcaee61
[2.0.x] Fix problems compiling with Arduino IDE ( #10441 )
...
* Fix problems compiling u8glib utf8 support on Arduino
* Change header in auto-generated font data
* Change include in font gen scripts
7 years ago
20772492aa
Fix compile warnings in AVR fastio.h ( #10440 )
7 years ago
f57a008c58
Merge pull request #10443 from thinkyhead/bf2_fix_and_improve
...
[2.0.x] Improve UBL mesh report, M420 V T, M421 N, and…
7 years ago
89b1580587
Fix compile error in tmc_status
7 years ago
52c024e260
M221 with no parameters report flow
7 years ago
01b01f6dfd
Tweak fwretract.retract debug, comments
7 years ago
e4acd2c40e
One fewer compare in _lcd_move_xyz
7 years ago
e05c825a05
Update position for UBL non-segmented activate/deactivate
7 years ago
d462be6de6
Try FIXFLOAT rounding based on sign
7 years ago
39c6f65ce7
Ignore LCD_BED_LEVELING with UBL
7 years ago
0746aff595
Improve UBL mesh report. Add M420 T, M421 N
7 years ago
3c826e5d05
Prevent delay when power is already on
...
Fix #10410
7 years ago
5a064d0e94
Fix bug in planner.set_position_mm
7 years ago
0945674ba2
Use H0 by default with UBL_MESH_EDIT_MOVES_Z ( #10428 )
7 years ago
6cb83758d7
Fix Brazilian Portuguese language duplicates
7 years ago
8f57e098de
Use end-of-line comments in planner.cpp
7 years ago
6c7a17dba6
Abort SD printing more safely ( #10407 )
...
Allow the current command to complete when aborting an SD print, otherwise some commands (G28, G29, etc.) will cause trouble.
7 years ago
c9aed73987
Fix missed includes from HAL macro patch ( #10416 )
7 years ago
9f8a96fb8a
Brazilian Portuguese update ( #10409 )
7 years ago
93273a4c9e
Fix u8g.h search path error ( #10419 )
...
Support env MARLIN_LANGS for user select generated language, and update doc; update script to generate dogm_font_data_ISO10646_1.h automatically.
7 years ago
584735c994
u8g.h => clib/u8g.h
7 years ago
29dda871cb
Patch "upload_disk" to make python happy
7 years ago
36b97bde9f
clear_block_buffer, kill_current_block in quick_stop
7 years ago
99282a46e9
Make sure ABL (manual) starts close to the bed
7 years ago
21f13f9e57
Stow Probe at end of G29 J3
7 years ago
6c535081ec
[2.0.x] Add optional menu item to toggle software endstops ( #10389 )
7 years ago
3c5c6d478a
Prettify process_parsed_command
7 years ago
0535ebc4d2
MESH_BED_LEVELING before PROBE_MANUALLY
7 years ago
bb7064cc30
Tweak MBL move to bed code
7 years ago
cc6d41e1d3
Use a macro for HAL header redirection ( #10380 )
7 years ago
12785583d0
[2.0.x] G33 MIN_STEPS_PER_SEGMENT ( #10386 )
7 years ago
c96412a78f
[2.0.x] UTF-8 language translation support ( #10213 )
7 years ago
daa712455b
Make sure MBL starts close to the bed
...
Fix #10390
7 years ago
4c8751727a
Fix M118 parameter handling
...
Fix #10388
7 years ago
3bc179a16f
Compress/update comments ubl_motion
...
…to fit more code on the screen and correct outdated commentary contrasting ABL.
7 years ago
646aa20b43
Overhaul of G33 Delta Calibration ( #8822 )
7 years ago
ac2e0afb62
Low Point for delta calibration ( #10363 )
7 years ago
57a899a412
[2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR ( #10373 )
7 years ago
85014cd132
[2.0.x] LPC1768 - automatic selection of upload disk ( #10374 )
7 years ago
8669dba5e6
Merge pull request #10172 from noingwhat/2.0.x-Filament-Change-Acceleration
...
[2.0.x] Filament load/unload add acceleration for Bowden
7 years ago
472ab0cc24
Tweak RAMPS SDSS pins
7 years ago
b94c8defee
Provide additional information about SMART-RAMPS board ( #10353 )
7 years ago
6f8e228880
Add RESET_PIN to pins_RAMPS_SMART.h
7 years ago
2d9b0a66fe
Add Filament Change accelerations
7 years ago
71d3523254
Add Filament Change accelerations to example configs
7 years ago
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
7 years ago
82dafbba33
Add Z_PROBE_LOW_POINT to example configs
7 years ago
a731a723e8
Better i3-2020 Z_PROBE_OFFSET_FROM_EXTRUDER
7 years ago
26cc12eaa4
Resolve corruption of Max7219 Debug LED Matrix
7 years ago
dca69efc11
Update Bed PID comments
7 years ago
56486c5c0e
Apply const to manage_inactivity
7 years ago
a6485456df
Fix LIGHTWEIGHT_UI with UBL
...
See https://github.com/MarlinFirmware/Marlin/issues/10317#issuecomment-379100702
7 years ago
e02fc4f1d6
Better RESTORE_LEVELING_AFTER_G28 sanity-check
...
As suggested by @GMagician
7 years ago
44a697ab04
Set STM32F1 TEMP_TIMER_FREQUENCY to 1K
...
Responding to https://github.com/MarlinFirmware/Marlin/pull/8833#issuecomment-379426803
7 years ago
cec6e19099
Add RepRapPro Huxley configuration
...
Based on #10343 by @indazoo
7 years ago
9ff4e9e1e6
Patch _IS_HW_SPI so defined() works
7 years ago
cea398849e
Tweak to gcode_line_error/return
7 years ago
a29adde5c0
Implement BEZIER_JERK_CONTROL
...
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
7 years ago
5932df7ea1
Add BEZIER_JERK_CONTROL to example configs
7 years ago
0e8242180d
Chamber temperature monitoring and auto fan control.
...
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
7 years ago
5b3bda1c16
Add Chamber Temp options to example configs
7 years ago
acda4ecb20
Fix DUE Trinamic SW/HW SPI sanity check ( #10336 )
7 years ago
ab715c70d1
TMC SPI sanity-check and pins debugging ( #10324 )
7 years ago
4dc7e64789
Update Slovak language
...
Based on #10313 by @rmoravcik
7 years ago
0dccf9ea6a
Merge pull request #10318 from marcio-ao/pr-einsy-retro-tmc2130
...
[2.0.x] Fix TMC2130 DIAG1 active high, Einsy Retro
7 years ago
2efc072fdb
Clear progress bar on completion ( #10333 )
...
Fix #10330
7 years ago
6ce060cfe0
[2.0.x] Update language_it.h ( #10322 )
...
Updated to #10296
7 years ago
9356cf648f
Added support for Einsy Retro
...
http://reprap.org/wiki/EinsyRetro
7 years ago
75037493fa
Default active low for TMC2130 DIAG1 ( #10294 )
...
- Added sanity check to inform users to set the endstop to inverting
when using SENSORLESS_HOMING
7 years ago
e8e60263c8
Scale feedrate (mm/s to deg/s) for SCARA
7 years ago
051303ad42
Russian language updates
...
From #10311 by @anton-piliugin
7 years ago
2fa0a73c2c
Implement filament change continuous purge
7 years ago
d133ad61f3
Add continuous purge to example configs
7 years ago
4b25543633
Backtrace formatting cleanup
7 years ago
902c885782
Switch to TMC2130 compatible hardware SPI & misc ( #10299 )
7 years ago
1c36606886
Fix MSG_HEATING_FAILED_LCD_BED macro evaluation
7 years ago
fe91514395
MBL should add z_offset regardless of fade ( #10308 )
7 years ago
8bc93c6f2b
Improve heating/cooling LCD messages ( #10293 )
7 years ago
21a47b50f4
Additional tool-change fixes ( #10304 )
...
Followup to #10257
7 years ago
f68b4265a6
Fix a probe pin definition
7 years ago
a019eebdd6
support utf8 unicode for test language ( #10220 )
7 years ago
656219d867
Add configs for Creality CR-8
7 years ago
7cbbc2af7a
[2.0.x] Optional heater signal inversion ( #10260 )
7 years ago
4d1a61335c
[2.0.x] Fixed Makefile for Marlin 2.0 ( #10255 ) ( #10281 )
...
* Fixed Makefile for Marlin 2.0 (#10255 )
- Makefile now supports the new Marlin 2.0 directory hierarchy.
- RELOC_WORKAROUND is now automatically enabled based on avr-gcc version.
* Makefile support for U8glib and TMC2130Stepper
- Updated paths for oliver's U8glib 1.19.1
- Added option for teemuatlut's TMC2130Stepper 2.2.1
7 years ago
241996d5d6
Merge pull request #10257 from thinkyhead/bf2_tool_change_debug
7 years ago
4c79dc1093
Fix a Serial+EEPROM compile error
...
Fixes #10278
7 years ago
93305a2d5e
Fix some spellings
7 years ago
adcb87f0db
Z Endstop Servo => Z Probe Servo
7 years ago
4f0eafce8f
Add more AVR boards to Makefile
7 years ago
4a23069de9
Fix Ender 4 / CR-8 compilation
...
- Assign 243 (like EFB) as Ender-4/CR-8 board ID
- Add to `Makefile`
- Add to `pins.h`
7 years ago
02f0f95d40
Handle disabled HYBRID_THRESHOLD in EEPROM ( #10275 )
7 years ago
9ec2c03c5b
Fix likely error in retract/recover
...
Addressing #10200
7 years ago
49f384a2ab
Note about MKS_MINI_12864 in sanitycheck
7 years ago
2672120a97
Do a small raise for all move-back
7 years ago
5acccbacc1
Simplified leveling-based tool change
7 years ago
1a75165f35
For set_z_fade_height use set_bed_leveling_enabled
7 years ago
d1734a089a
Split up tool_change for some setups
7 years ago
a9f94f260a
Some RADDS pin updates
7 years ago
31df43212c
Use lcd_printPGM_utf in more places
...
Fix #10256
7 years ago
7d8a46519f
Output ABC for delta stepper counts
7 years ago
6098efcc59
Use float62 for LCD edit of Z Fade
7 years ago
f6d13e2295
Allow Z_SAFE_HOMING sanity checks to handle floats
7 years ago
889fd5f71f
Backtrace minor cleanup
7 years ago
53f0c7522a
Symmetrical FWRETRACT Z Hop
...
Do the Z lift normally before setting Z back to its prior value. But do the Z lower using spoofing. This should produce proper symmetrical movement.
7 years ago
ac7e97f4fe
Change order of inactive stepper disable/enable
...
This ensures that steppers that share an enable pin will only be disabled for a miniscule time.
7 years ago
55e9b85ad6
Clear the "Wait for user" message set by M0/M1
...
See https://github.com/MarlinFirmware/Marlin/issues/10246#issuecomment-377146936
7 years ago
b6a55f0891
Temporary workaround for tool-change compile error
...
Pending a more complete solution to tool-change Z deviation.
7 years ago
b852781eba
Fix BLTOUCH compile error
...
Followup to #10250
7 years ago
c1f58a238d
No delay in sensorless quick homing ( #10254 )
7 years ago
1be955e52a
Alert users about low Z jerk values
7 years ago
9e4c037cef
Wait before turning off PRINTER_EVENT_LEDS at print end ( #10248 )
7 years ago
8b7381b626
Clear sensorless homing in home_delta after first move-to-top
7 years ago
dbe2b6f7b0
Do moves towards endstops differently in do_homing_move
7 years ago
d573a2cada
Fix pins_RAMPS.h for 32-bit platforms
...
Followup to 436e5b7
7 years ago
f04be05a14
"G28 Z Forbidden" => "Home XY first"
...
Some languages will need to be updated for proper phrasing
7 years ago
a97624dd81
Allow pinsDebug "Analog in" long int
7 years ago
7b8bb2519e
Fix gcode_line_error call
...
Followup to 3007eee
7 years ago
aa20b3ef7c
Fix linear/3-point manual leveling buffer overrun
...
Fixes #10137
7 years ago
cbdc78ec0f
Fix STM32 compilation with PlatformIO ( #10245 )
7 years ago
9d2ea5d64b
Undo German changes
...
See 941e9bd329 (commitcomment-28262166)
7 years ago
2bc7f416ee
Fix missing comma in tmc_sgt
...
Fixes #10209
7 years ago
38378cd0e8
M218 with DELTA needs planner.h
...
Fix #10232
7 years ago
3007eee22e
Require a checksum when writing to SD
...
From #10204 by @adriancuzman
7 years ago
9656a82609
Fix G53/CNC_COORDINATE_SYSTEMS compilation, Travis testing ( #10227 )
7 years ago
749f19e502
[2.0.x] Move backtrace to a shared location ( #10237 )
...
- And implement the `backtrace()` function call
7 years ago
7dc256432f
Restore STM32F1 series to working order. ( #10229 )
...
The `_O2` attribute is no longer needed on the malyanlcd function, and the macros have broken timer numbers - reset this to a function to return the right device. Also fix the bit order cast in SPI.
7 years ago
d1f14202a9
[2.0.x] NANODLP_Z_SYNC requires linear axes ( #10240 )
7 years ago
b287560258
Fix say_M603
7 years ago
436e5b7ea3
Apply spacing in pins files
7 years ago
4d533b9baa
Update bq Hephestos 2 probe offset
...
From #10234 by @thopiekar
7 years ago
78df07ac71
Merge pull request #10221 from ejtagle/bugfix-2.0.x
...
[2.0.x] DUE: Several fixes to the backtracker
7 years ago
8934a2c49b
Added some missing Thumb instructions to the traceback follower, so now it is able to traceback through switch() statements
7 years ago
328edea03a
Several fixes to the backtracer. Tested ant it works
7 years ago
aa6dacbbdf
German update
...
Based on #10216
7 years ago
8322a79bb9
update the UTF-8 C strings for Chinsee languages, for Simplified and Traditional Chinese ( #10211 )
7 years ago
9a24c0ae3f
Tons of fixes to the backtracker code, and also added an extra backtracker that does not require unwind tables to work and it is used if unwind tables are absent
7 years ago
a891af2f7a
Enforce minimum TMC2130 / TMC2208 libs
7 years ago
75b381cd28
Merge pull request #10203 from Bob-the-Kuhn/sanity-check-fix
...
[2.0.x] Fix TMC sanity checks that always fail
7 years ago
433e984d1f
move comment to fix compile error
7 years ago
f7857ac8a8
Merge pull request #10185 from ejtagle/bugfix-2.0.x
...
[2.0.x] DUE debugging: Solve WDT startup delay, add traceback & crash report uses programming port baud rate
7 years ago
b756a15aba
another needs to be deleted
7 years ago
50c81ebe0d
remove check that always fails
7 years ago
3ac135cef3
Enforce minimum TMC2130 / TMC2208 libs
7 years ago
8870f9b1da
Fix M503 helper functions following TMC updates ( #10197 )
7 years ago
bb7236a750
Z correction on tool-change for all HAS_MESH ( #10199 )
7 years ago
509227fd80
change to mode 0
7 years ago
c3b23974bd
Added detection of case when no unwind tables are available
7 years ago
ea1a83ce41
Use pgm_read_ptr for tables of pointers
7 years ago
9da0797e29
Fix EEPROM size of tmc_hybrid_threshold
...
Followup to #10102
7 years ago
daf643e1ce
[2.0.x] TMC: Match axis label order ( #10188 )
7 years ago
1628a9e864
make data declarations consistent
7 years ago
b210bdf032
Now the Crash reporter uses the configured BAUDRATE to send the report through the Programming port. And also shows the traceback of functions as discussed. For that latest feature to work, you need to compile the project with -funwind-tables and -mpoke-function-name compiler flags
7 years ago
Scott Lahteine