bfd9728cf4
Serial buffer over run work around for v2.0.0 ( #9236 )
...
* Work around for serial buffer over run
PronterFace sends a lot of M105 commands. During long operations such
as UBL's G29 P1, G29 P2, G29 P4 and G26 this can over run the serial
buffer. This results (very often) in a M1 (actually a M1M105) ending
up in the command queue.
Until we figure out a better way to resolve this issue, this will keep
the UBL commands from experiencing bogus commands at thier completion.
7 years ago
c371bdc499
Expand RAMP case light possibilities
...
Pin 6 is only used by servos when 2 or more of them are used
7 years ago
7c18c2ea5f
Fix LCD timer string length
7 years ago
9d0cf02fef
Correct mesh size calculations
7 years ago
c7bad74d8f
Merge pull request #9202 from benlye/m73-bugfix
...
[2.0.x] Fix progress bar duration when time is exactly 86400s
7 years ago
af9b32e3b9
Give PronterFace time to print the UBL What information...
...
Give PronterFace time to print the UBL What information...
7 years ago
acb1e31374
Fix UBL Mesh Size regression
7 years ago
f5f1b069ad
Convert UBL mesh tilting to all use the same algorithm ( #9204 )
...
A number of regressions were patched also. The UBL G29 P2 and P4 Press and Hold had stopped working. It is very possible this is broken in the bugfix_v1.1.x branch also.
The main purpose of the Pull Request is to get the 3-Point mesh tilting to use the LSF algorithm just like the grid based mesh tilt. This simplifies the logic and reduces the code size some what. But the real reason to do it is the 3-Point case can be solved exactly. And by feeding these numbers into the LSF algorithm it provides a way to check all that code for 'correctness'.
7 years ago
554d849827
Fix duration when time is exactly 86400s
7 years ago
6f1bf5d212
LPC1768: Config: default to SDSORT_LIMIT = 64 instead of 256
7 years ago
1e65562d55
LPC1768: HAL: only initialise used HardwareSerial ports
...
Misc formatting
7 years ago
9dacd54a50
Get FT-i3-2020 configuration files into compliance with ?_BED_SIZE
7 years ago
d178d6e921
M503 patch for EEPROM_CHITCHAT off
...
Fix #9155
7 years ago
fa432508b0
Followup to Ender config
7 years ago
6856eccc77
Master-only TwoWire class for LPC1768
7 years ago
d5bf9e74c4
Merge pull request #8996 from p3p/pr_bf2_more_adc_filter
...
[2.0.x] PID control fix and more LPC1768 ADC filtering
7 years ago
4d2f277d43
Merge pull request #9189 from psavva/tmc_debug_compile_fix
...
[2.0.x] Fixes TMC_DEBUG compilation error
7 years ago
43d3d024ac
Update tmc_util.cpp
7 years ago
ad500b01e0
Fixes TMC compilation error
7 years ago
f4e4c7a7c8
Merge pull request #9188 from thinkyhead/bf2_creality_ender
...
[2.0.x] Add Creality Ender config/board
7 years ago
2038722c52
LARGE_FLASH obsolete
7 years ago
f887719a40
Creality Ender board support
7 years ago
9a2dd0bc5a
Creality Ender 2/4 configuration
7 years ago
2c18faf3e4
General cleanups for HAL
7 years ago
42933c804a
Cleanups for STM32F7
7 years ago
a0246c5c96
Add support for STM32F7 MCU
7 years ago
a27fa80a7e
More featureful CR-10S configuration
7 years ago
1a3d2ad275
Merge pull request #9168 from marvin-sinister/rename-M100-2.0.x
...
[2.0.x] Rename M200 pins file to uppercase
7 years ago
a408209d24
More reliable temperature serial report?
7 years ago
5f807e37c5
A second rename saves nine
7 years ago
3ae41e5f7f
Merge pull request #9152 from thinkyhead/bf2_anti_stutter
...
[2.0.x] Ensure smooth printer movements
7 years ago
02ff12d491
More up front option to show SD percentage
7 years ago
3b15c88225
Merge pull request #9153 from thinkyhead/bf2_malyan_support
...
[2.0.x] Fix support for Malyan M150
7 years ago
e753d6298f
FLSUN Kossel example configs
7 years ago
77c2d810f9
Bring configs up to date
7 years ago
3952070800
Link to marlinfw.org boot screen tool
7 years ago
0cd397a3f8
Add instructions for Malyan M150
7 years ago
344ebc3bd2
Create and use pins_MELZI_MALYAN.h for Malyan M150
7 years ago
094e9b1dab
Remove ARDUINO_ARCH_SAM from serial.h too?
7 years ago
c37d38886c
Fix serial.h avr block
...
Followup to #8148
7 years ago
4f5e087ff4
Planner anti-stutter by Sebastian Popp
7 years ago
ac368f2788
Add STEPPER_ISR_ENABLED() to HALs
...
Some also get a `HAL_timer_interrupt_enabled` function.
7 years ago
5578dccaa0
Merge pull request #9161 from tcm0116/2.0.x-eeprom
...
[2.0.x] Fix EEPROM SettingsData for 32-bit architectures
7 years ago
6ba8cf8405
Merge pull request #9163 from GMagician/2.0.x-SD-issues-fix
...
[2.0.x] sd issue fix
7 years ago
50c55b25f7
Renamed to upercase
7 years ago
6667a916a4
Indentation fix
7 years ago
be717b3c07
Save some program memory
...
This will save some program memory with no speed lose
7 years ago
f37c64ee5b
Fix unsupported CMD59
...
It seems that some SD cards don't support CRC_ON_OFF command. This fix will permit to use also these cards but leaving CRC check active on the system
7 years ago
cfd989d7c5
Fix EEPROM SettingsData for 32-bit architectures
7 years ago
da600e5fbe
Merge pull request #9132 from Bob-the-Kuhn/add-VIKI2-to-Travis
...
[2.0.x] add VIKI2 test to Travis & fix LCD contrast (again)
7 years ago
742cff5f3c
Followup to #9141
7 years ago
84de428d30
[2.0.x] Fix compile errors ( #9141 )
...
* Update persistent_store_impl.cpp
* Remove define BYTE from serial functions since Arduino docs typically show 0 for the normal case.
7 years ago
e633ce06c7
LCD contrast type mismatch is back
...
WORKS!
7 years ago
e654ea1e1a
Merge pull request #9130 from thinkyhead/bf2_tmc_followup
...
[2.0.x] More TMC followup
7 years ago
8ac246162e
Creality CR-10S configurations
...
Provided by printedsolid.com
7 years ago
048486390e
Bring some configs up to date
7 years ago
6a043eee55
Various updates for TMC support
7 years ago
d7fd78cb91
Merge pull request #8148 from tcm0116/2.0.x-multi_host
...
[2.0.x] Add multi-host support
7 years ago
a8c446c3bc
[2.0.x]DUE: Fix includes for SDSUPPORT ( #9112 )
7 years ago
f7efac57b7
Multi-host support
7 years ago
dabb75034c
Update example configurations
7 years ago
6a50adb4d5
works
7 years ago
5c076a6d93
Improved M915 description
7 years ago
a94104dbb5
Merge pull request #9113 from teemuatlut/TMC_followup
...
[2.0.x]TMC followup
7 years ago
554e577676
SERIAL_STATS_* features not supported on USBCON targets ( #9127 )
7 years ago
2db666e99a
Enable USE_ZMIN_PLUG on SCARA example ( #9126 )
7 years ago
7e000e6af4
More EEPROM field debugging ( #9123 )
7 years ago
3a99dc7c5c
2.0.x Fix compiler warning ( #9116 )
...
Fix duplicate language define warning
7 years ago
5295b4713d
[2.0.x] add semitec 104NT-4 ( #9119 )
...
Table is very very similar to old 104-GT2 so I added only the name and recycled old ID
7 years ago
cdc61ebf53
Add M915 configuration option
7 years ago
9d923c6c03
Fix TMC gcode commands
7 years ago
99516572b1
Fix TMC current read from EEPROM
7 years ago
f26805e862
[2.0.x] UBL Mesh Storage Message ( #9095 )
7 years ago
14dcad6bbc
LPC1768: Increase ADC median filter from 3 values to 23
...
Clarify the HAL_adc_get_result method to make sure correct values enter the filters
HAL: Fix the PID control loop for non-AVR platforms
7 years ago
60d07f20e7
Make mbl.has_mesh() a method
7 years ago
86818c9a89
Move MBL functions into the class
7 years ago
bbb8d4c802
Set has_mesh if user issues G9 S3
...
Prevents user from having to manually run through entire manual leveling process only to enable mesh so they can manually restore their offline mesh backup
7 years ago
2b5a9be49c
Fix M503 skew output
...
Followup to 19e75ccf86
7 years ago
cf2922f164
Laser/spindle PWM off on M5
7 years ago
5fb6dd1424
Bmp fix
...
Clockwise arrow fixed
7 years ago
cb0e826c5d
Merge pull request #9068 from Bob-the-Kuhn/SD-detect
...
[2.0.x] SD card detect improvement
7 years ago
f72b0a7b04
1234
7 years ago
702c8acdd5
Settings FIELD_TEST fix
7 years ago
e89f1453ab
UBL G29 works without settings.load()
7 years ago
950be70a33
Add FIELD_TEST to validate storage
7 years ago
760c912ab9
Add data size validation
7 years ago
b91ca168fb
Add a struct defining EEPROM storage
7 years ago
51e0f2bee3
Add MarlinSettings::validate()
7 years ago
878f54c27b
Write filler with NO_VOLUMETRICS
7 years ago
3ea6745b36
Pretty up TMC current write
7 years ago
3319765034
Detab some HAL files
7 years ago
1c41de16d4
Trailing whitespace clean
7 years ago
1746a7352e
Merge pull request #9042 from thinkyhead/bf2_M701_M702
...
[2.0.x] Improved Pause/Load/Unload, M701-M702
7 years ago
048d8a0158
CheapTRONIC v2.0 additions/revisions
...
Based on #9030
7 years ago
3a4e107b6b
use SERIAL_EOL(); instead of new line string
7 years ago
a5dfe08a81
Add precision to planner.xy_skew_factor so it doesn't print as 0.00
7 years ago
19e75ccf86
Add enough precision so planner.xy_skew_factor doesn't print as 0.00
7 years ago
4fb60e1562
M702.cpp => M701_M702.cpp
7 years ago
7541316bb4
Add M701/M702 Filament Load/Unload, M603
7 years ago
81211da7b4
M701 / M702 language changes
7 years ago
8704e533da
Apply FILAMENT_LOAD_UNLOAD_GCODES to example configs
7 years ago
455592eee8
Improvements to LCD menu macros
7 years ago
a80f2eea23
Group leveling reports for folding
7 years ago
190cd0a111
Nozzle park args
7 years ago
0e93506985
Fix for issue #9005 , #8942 - Bed PID autotuning ( #9036 )
7 years ago
016e46a3c0
Merge pull request #9009 from Bob-the-Kuhn/Due-RRDFG-power-up-garbage
...
[2.0.x] Due - fix power up garbage on RRDFG LCD
7 years ago
31582caa07
2.0 Fix for bad Pause extruder position resuming ( #9029 )
7 years ago
4626d04067
as good as i can get it
...
minor edits to force new Travis test (last one timed out)
Update u8g_com_HAL_DUE_st7920_sw_spi.cpp
initial power up display garbage gone
7 years ago
4af3d436b2
M303 pid autotune cleanup, commentary
7 years ago
e5b71af8c9
snapshot
...
found a few more nasties
7 years ago
724e3f33bc
Merge pull request #9001 from Tannoo/(2.0.x)_LCD_EEPROM_init_fix
...
[2.0.x] EEPROM init fix
7 years ago
959a2d2527
Add beginTransaction to HAL SPI ( #9019 )
7 years ago
e43f3ac989
EEPROM init fix
7 years ago
fc67c64b8f
Merge pull request #8989 from tcm0116/2.0.x_ubl
...
[2.0.x] Fix UBL compilation warnings
7 years ago
8afc4f8d9d
Fix UBL compilation warnings
7 years ago
eca5cc8669
Merge pull request #9003 from Bob-the-Kuhn/Due-PINS_DEBUG-&-related
...
[2.0.x] add Due PINS_DEBUG support & misc improvements (replaces PR #8990 )
7 years ago
e9fc7bc69c
Merge pull request #9000 from Bob-the-Kuhn/2.0-LCD-contrast
...
[2.0.x] lcd_contrast type mismatch work around
7 years ago
5574fad69c
copy of PR #8991 code
...
Formatting tweaks
correct array initialization & remove test code
7 years ago
d190c702de
Add MKS_BASE Microstepping pins
...
Based on #9008
7 years ago
5e01ee8adf
Temperature updates for parity with 1.1.x
7 years ago
adb9ecf3cc
copy of PR #8990
7 years ago
39e5fabfa9
Z BabyStepping should not be dependent on a bed leveling system being active
7 years ago
ef911a2d12
works
7 years ago
d80c4f1a6e
Fix typo in delta call to buffer_line
...
Fix #8901
7 years ago
9312ee63b0
Merge pull request #8979 from thinkyhead/bf2_sync_up_configs
...
[2.0.x] Synchronize configs with 1.1.x
7 years ago
41dfb229ec
Merge pull request #8978 from thinkyhead/bf2_slimming_option
...
[2.0.x] SLIM_LCD_MENUS option
7 years ago
3dd04736c0
Update M17_M18_M84.cpp
7 years ago
2929c9e56f
A specific option to SLIM_LCD_MENUS
7 years ago
10edb469bb
Apply SLIM_LCD_MENUS to example configs
7 years ago
5294fd132f
Merge pull request #8924 from ejtagle/bugfix-2.0.x
...
[2.0.x] Improve SW SPI for DUE a bit more
7 years ago
0b4a46fa6c
Bring configs up to date with 1.1.x
7 years ago
7cc2193bce
Add Tronxy X1 example config ( #8972 )
7 years ago
729a9f55fc
Improved Sw SPI on DUE HAL a bit more.
...
Now the USB MSD can transfer at 750k/s. Previously, it was 500k/s. I think this is the maximum achievable speed using Sw SPI.
7 years ago
615146c069
Enqueue commands better in ultralcd.cpp
7 years ago
9686ffedef
Single pause flag also indicates SD print pause
7 years ago
6d94bbf618
Apply some PGM_P pointers
7 years ago
cba44128d5
fix include
7 years ago
427df8792d
Fix Capabilities Report
7 years ago
2526ac6500
Display up to 3 extruders on char LCD
...
…and show bed level indicator at the position of the [H] icon, when a heated bed exists.
7 years ago
db32c185ae
Merge pull request #8860 from Bob-the-Kuhn/2.0.x-DUE-RRDFGSC
...
[2.0.x] DUE - update for Reprap Discount Full Graphic Smart Controller
7 years ago
9ecdd1f4c7
Multi extruder support for M600 and LCD
7 years ago
a1ce6e8ff4
Clear lcd_clicked immediately on use
7 years ago
5effe1590c
Fix NO_VOLUMETRICS bug
7 years ago
f163eede78
No sub-menu if NO_VOLUMETRICS
...
For parity with #8911
7 years ago
2c4e03d2cf
Indentation of a SW SPI file
7 years ago
1a827d5b68
Opening brace tweaks
7 years ago
a142fab155
Enable RRDFGSC on Due
7 years ago
b259bb4670
Fix tmc_util global vars
7 years ago
4ef965cc40
Fix compiler warnings
7 years ago
9e8008c49c
Fixes for G29, esp. 3POINT
7 years ago
026e301307
lcd_map_control deps on ULTIPANEL
7 years ago
f2731c9f93
Allow consecutive uses of G29
7 years ago
4b49ea1e92
General cleanup of config-store, reset_bed_level
7 years ago
2925852244
Fix GT2560 A+ servo pin
7 years ago
c6354fa153
Tweak M125 code
7 years ago
3b51f5c67e
Add pause/resume action to example configs
7 years ago
f704f405af
Add pause/resume actions on M600, M125
7 years ago
f0a8a1a853
[2.0.x] Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE ( #8866 )
...
* Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE
7 years ago
705ea98fd3
Comment `return false` in motion functions
7 years ago
50366b00d5
Tweak cleaning buffer / SD finished command
7 years ago
28fc8741d6
Reduce default jerk. XY by half. Z by 1/4
7 years ago
1a948cbd93
Fix SET_OUTPUT glitch - LPC1768 & DUE
7 years ago
869c89d83f
Merge pull request #8865 from thinkyhead/bf2_more_scara_scaling
...
[2.0.x] SCARA Feedrate Scaling for G2/G3 - using HYPOT
7 years ago
1cf1cf8759
Add RADDS_DISPLAY to example configs
7 years ago
ea1a8d1223
add original RADDS LCD + Controller
...
adds setup for the original Radds Display+Controller+SD Card Reader PCB
http://doku.radds.org/dokumentation/lcd-display/
7 years ago
4a8fd8ae92
Merge pull request #8853 from ejtagle/bugfix-2.0.x
...
USB Mass Storage Implementation / CDC with HW flow control and misc fixes and improvements for Arduino DUE/RE-ARM based boards
7 years ago
aa97cd6e9b
Merge pull request #8871 from petrzjunior/bugfix-2.0.x
...
[2.0.x][Language] Update Czech for Dec 2017
7 years ago
2917d1217d
Revert "Followup to #8698"
...
This reverts commit 4e891e9fb7
7 years ago
69a51a426c
Update Czech language Dec 2017
7 years ago
caa5093498
General DELTA_IK macro
7 years ago
c694608450
Apply SCARA_FEEDRATE_SCALING to G2/G3
7 years ago
97d509d4d2
Revert "Improved Core-compatible jerk code"
...
Reverting commit 3cd7659
7 years ago
5bc2acc072
Restore position_float to fix LIN_ADVANCE
7 years ago
33a6fc70e4
Adding USB MSD implementation to the HAL: Now, when you plug the Native USB port of the Arduino DUE to your PC, it will be detected as a composite USB device: One of the devices is a USB CDC (Serial port over USB) with native USB handshake (no more overflows!!) (set SERIAL_PORT to -1 to use it as main serial port) and also, a MSD (USB Mass Storage Device) will be detected, and the SD card present on the socket will be reflected as a Removable disk on your PC)
7 years ago
d8a4db72ac
Reimplemented SW SPI for DUE in assembler. This allows to reach 12Mhz as SPI Clock and improves 4x the transfer speed to the SD card. This is REQUIRED so access to SD from USB is usable (allows 600Kbytes/second transfer speeds)
7 years ago
99b2fc2066
Adjusted timings on the ST7290 u8glib so RE-ARM and RAMPS4DUE have no problems when writing to the graphics LCD. This fixes Issue #8787 - Special thanks to Bergerac56 for testinf this out !!!
7 years ago
498ea7512a
Exposed SDCard interface to the public, to USB MSD is able to read/write sectors on the SD card
7 years ago
9aff55ed1f
Backported latest improvements and fixes from the SdFat liibrary to our own version. This includes support for CRC7 validation on commands and also, made sure that even if using software SPI implementations, SD card speed is properly adjusted when transitioning from INITIALIZATION to DATA TRANSFER mode. ALL HALs implement spiInit, even in SW SPI mode, and we NEED this change to improve 25x the transfer speed of the SD card and allow implementations of USB MSD
7 years ago
7447979110
Fixed some warnings on the MakerParts configuration, when compiling using the AVR toolchain (integer overflow on the preprocessor calculations)
7 years ago
b6f9c333d4
Adding hooks into the idle loop so HALs can execute 2nd plane tasks, such as serving SD card read/writes requested from the USB MSD layer
7 years ago
2ec4113cb2
Changes to STM32F1 HAL ( #8833 )
...
Some to correct missing files from previous PR to completely avoid
HardwareTimer Class (reduce overhead). Some changes to formatting.
Changes to DMA ADC to work correctly.
Change to F1 sanity check.
7 years ago
913d9e9a59
Matching sign across filwidth vars
7 years ago
3cde4c78b2
Use wildcard *.cpp in Makefile
...
Based on #8738
Addressing #8731
7 years ago
fdc5e72720
A single setting to validate filament width
7 years ago
93a6a4e1a8
Add VOLUMETRIC capability item
7 years ago
933f76fda3
Option to disable all volumetric extrusion
7 years ago
31e33d2acd
Add NO_VOLUMETRICS to example configs
7 years ago
fc9ee1a4de
Fix up serial sanity check
7 years ago
de5ca96654
More parity with 1.1.x, plus whitespace
7 years ago
a891d8d738
Merge pull request #8820 from thinkyhead/bf2_mks_sbase_spi
...
[2.0.x] Fix SDSUPPORT for MKS SBASE
7 years ago
097a26007f
Fix SDSUPPORT for MKS SBASE
...
Fix supplied by @cjsoong in https://github.com/MarlinFirmware/Marlin/issues/8750#issuecomment-350779983
7 years ago
8df5955da4
Revert "Reset timer count before first block step"
...
This reverts commit 5cf6a062e3
7 years ago
957bbab57f
Update inc files for parity with 1.1.x
7 years ago
f79026acc1
Apply MKS_12864OLED_SSD1306 to examples
...
Followup to #8814
7 years ago
b055d8c39c
[2.0.x] Adding support for using the MKS_12864OLED with the SSD1306 controller ( #8814 )
...
* Adding support for using the MKS_12864OLED with the SSD1306 controller
* Update comment for correct controller type
7 years ago
15d05748df
Adding support for the Tronxy and Zonestar LCD
7 years ago
9abbcc3ee0
Apply ZONESTAR_LCD to example configs
7 years ago
aed0cfa3d1
Various fixes for 2.0.x configs
7 years ago
674deaf223
Add NANODLP_ALL_AXIS to config examples
7 years ago
5595098063
V2 Extended NanoDLP_Z_Move_Sync to G4 & G28,Added all axis option.
7 years ago
2b7db90340
Bring Malyan M200 config up to date
7 years ago
8b12371e45
Change some hex case
7 years ago
4782acf60e
Merge pull request #8780 from fiveangle/bf2-typo
...
[2.0.x] typo in Marlin.cpp
7 years ago
0cd1e91056
[2.0.x] TMC driver update ( #8769 )
7 years ago
09d13f186f
Correct unskew, after all
7 years ago
0d531d9655
Missing HAS_HEAT_BED conditional
...
Fixes issue found in #8779
7 years ago
69efb87d19
typo in Marlin.cpp
7 years ago
368c124de8
Fix Planner::unskew parity with skew
7 years ago
cf2193c07f
Comment, fix filament width sensor
7 years ago
a641992c1d
Merge pull request #8762 from victorpv/patch-2
...
[2.0.x] STM32F1 HAL: Fix issue #8585 . Updates to readme.
7 years ago
ac168a03c8
Fixes for the Arduino DUE HAL (Serial Port, Graphics Display, EEPROM emulation) ( #8651 )
...
* Fixing the DUE serial port assignments: Now -1 means the SAM3x USB Device emulating a serial port, and 0 means the USB to serial adapter included as a programming port
* Improving the Fast IO port access implementation on Arduino DUE
* Implemented EEPROM emulation on Due by storing data on the internal FLASH (with wear leveling)
* Implemented a Software SPI for the ST7920 graphics display for the Arduino RAMPS for DUE, as the default one in u8glib is clocking data too fast on ARM, and the display does not understand it.
* Fixing the case where the serial port selected is the USB device
* Adding configuration for the Makerparts 3D printer (www.makerparts.net)
* Tuned MakerParts acceleration on X and Y axis so it never loses steps. Also adjusted pulses per mm to match default hw configuration
* Fine tuned Maximum acceleration for MakerParts printer
* Style cleanup
* Style cleanup (2)
* Style fixes (3)
* Fixing the DUE serial port assignments: Now -1 means the SAM3x USB Device emulating a serial port, and 0 means the USB to serial adapter included as a programming port
* Improving the Fast IO port access implementation on Arduino DUE
* Implemented EEPROM emulation on Due by storing data on the internal FLASH (with wear leveling)
* Implemented a Software SPI for the ST7920 graphics display for the Arduino RAMPS for DUE, as the default one in u8glib is clocking data too fast on ARM, and the display does not understand it.
* Fixing the case where the serial port selected is the USB device
* Adding configuration for the Makerparts 3D printer (www.makerparts.net)
* Tuned MakerParts acceleration on X and Y axis so it never loses steps. Also adjusted pulses per mm to match default hw configuration
* Fine tuned Maximum acceleration for MakerParts printer
* Style cleanup
* Style changes to u8g_dev_st7920_128_64_sw_spi.cpp
* Even more improvements to the FastIO HAL for DUE. Now WRITE() is 2 ASM instructions, if value is constant, and 5 cycles if value is not constant. Previously, it was 7..8 cycles
* After some problems and debugging, seems we need to align the interrupt vector table to 256 bytes, otherwise, the program sometimes stops working
* Moved comments out of macro, otherwise, token pasting does not properly work sometimes
* Improved Software SPI implementation on DUE: Now it honors the selected speed passed to spiInit(). This allows much faster SDCARD access, improving SDCARD menus and reducing latency
* Update u8g_dev_st7920_128_64_sw_spi.cpp
* Disabling EEPROM over FLASH emulatiion if an I2C or SPI EEPROM is present
7 years ago
084f2434a7
Update readme.md
7 years ago
7c7ae5ebef
Delete duplicated file.
7 years ago
4feffca178
fix for issue #8585
...
As reported in this issue:
https://github.com/MarlinFirmware/Marlin/issues/8585
I have it working fine in my local copy like that change.
7 years ago
d568e586b7
Fix up ubl_motion indentation
7 years ago
24f9bec6f4
UBL + DUAL_X_CARRIAGE compatibility
7 years ago
6d0678d963
Omit unused UBL motion code
7 years ago
3255712343
Skew Correction for UBL
...
Also remove unused grid slicing function when using UBL segmented.
7 years ago
3d796d8040
Move debug code
7 years ago
3db5303bfe
_buffer_line => buffer_segment
7 years ago
a71d2f3f40
UBL_DELTA => UBL_SEGMENTED
7 years ago
73e32925e4
References are better for array args
7 years ago
125c572d97
Tweak M114 detail
7 years ago
a5150c83a2
[2.0.x] Multiple updates to STM32F1 HAL ( #8733 )
...
* STM32F1 HAL
Adding files for STM32F1 HAL based on libmaple/stm32duino core.
Current persistent_store uses cardreader changes to be sent in separate
commit, but could be changed to use i2c eeprom.
There is another persistent_store implementation that uses the MCU flash memory
to emulate eeprom
Adding readme with some information about the stm32 HAL.
* Switch to Timer4 to avoid a hard reset on STM32F103C6 boards
On bluepill STM32F103C6 boards, using Timer5 results in a error() vector call. Switch to 4 since these are both general purpose, 16 bit timers.
* Add support for EEPROM emulation using Flash
Some low end machines doe not have EEPROM support. Simulate it using the last two pages of flash. Flash does not allow rewrite between erases, so skip writing the working version if that's enabled.
* Basic Pins for a malyan M200
This is a work in progress to go hand in hand with the STM32 work.
* Add support for ADC with DMA. This work has exposed a problem with the pin enumerations in STM boards vs what marlin expects (i.e, try defining PA0 as a temp pin). The hack can be removed with we go to fastio completely. To see this work, set something in adc_pins to a value like PA0 and connect your pullup resistor'd thermistor.
* Missing file - change HAL_adc_init to actually do something
We have an actual ADC init function now.
* Remove pinmode hack
Remove the pin mode hack that I was using to init PA0.
Updated Readme.md
* Several changes to timers and GPIO
Faster GPIO, and faster timer functions by accesing registers and
libmaple.
Still more changes pending for the Timer's code to skip using the
HardwareTimer class altogether.
Switch all enums to be within #defines
This change allows a user to have, for instance, TEMP_4 and TEMP_BED definied but nothing else. The enums which are not defined move "out", allowing the first ones to take the slots in the enum, and since the array is sized on ADC_PIN_COUNT, we always have the right size data and in order.
* Update Malyan M200 pins
Update Malyan M200 pins with correct fan values.
* Test all pins on actual hardware, update definitions
Some of the pin definitions were from knowlege base/pdfs. Now they've been tested against actual hardware. This should be very close to final.
* Update HAL_timers_Stm32f1.cpp
* Add sample configurations for Malyan M200
Add sample configuration for Malyan M200 without bed leveling, and move fan to auto cool E0 since this printer by default has only one fan.
Choose the timer based on MCU defintion. Timer5 is not valid on C8/CB class boards, so use Timer4 for the step timer.
readme.md update
* Updates to timers, and some stm32 boards definitiions
* Correct pin toggle macro.
* Remove duplicated Malyan M200 entry from pins.h
* Update configuration_store.cpp
* Formatting, indentation
* Formatting in HAL_Stm32f1.cpp
7 years ago
204199e1ce
Only compare XYZ to check motion
7 years ago
6686d937fb
Always report position on config load/reset
7 years ago
117fc872a7
Update current position in M852
7 years ago
7d2e850577
Have M420 report a changed position
7 years ago
03ba79f144
Sync and report changed position
7 years ago
5cf6a062e3
Reset timer count before first block step
7 years ago
6149b82119
Allow setting current timer counter
7 years ago
82ef6b5242
Add an option to specify "pulse" timer
7 years ago
b8bc965414
General cleanup HAL timers
7 years ago
69d49a2438
Shorter segments may be better
7 years ago
d576f5408e
Add MiniRAMBo 1.0a board
7 years ago
c40cb52342
Use MB() for Megatronics 3.1
7 years ago
4fa65a5c25
TCNT0 => HAL_timer_get_current_count
...
Fix #8710
7 years ago
b3daf6b5db
[2.0.x] better reverse pass ( #8722 )
...
* repair reverse_pass()
And make it readeble.
This was broken a long time ago.
Not competely unfunctional but far from optimal.
* Minor speedup when calling calculate_trapezoid_for_block
2 float / to 1 foat / and 2 float *
* Various style changes
7 years ago
f58eb391aa
[2.0.0] Better off mesh behavior for UBL ( #8714 )
...
* Better off mesh behaviour for UBL
* Suggested ubl.h changes
7 years ago
cffd052fee
[2.0.x] Fix for #8604 ( #8717 )
...
* Nozzle.cpp: replace incorrect M_2_PI (2/pi) with 2.0 * M_PI
* Use RADIANS(360) instead of 2 * M_PI
7 years ago
65d0f32f82
divide only when required
7 years ago
728acf521c
Followup to #8706
7 years ago
85c6ffbe0d
Discard all "continued" blocks on interrupted move
7 years ago
4e891e9fb7
Followup to #8698
7 years ago
de3d3b9cb1
Put FORCE_INLINE before static
7 years ago
43ea265b78
Merge pull request #8685 from MateuszKrawczuk/patch-3
...
Update TEMP_BED_PIN in MIGHTYBOARD_REVE
7 years ago
ae663a4198
PROBE_DOUBLE_TOUCH => MULTIPLE_PROBING
7 years ago
d7800e7975
Apply MULTIPLE_PROBING to example configs
7 years ago
542efda7db
Merge pull request #8698 from thinkyhead/bf2_replace_jerk_code
...
[2.0.x] Improved Core-compatible jerk code
7 years ago
3cd7659924
Improved Core-compatible jerk code
7 years ago
99fcf60977
[2.x] addressing #8644
...
Removed missing include file
7 years ago
81c0a918af
feed_factor => inverse_secs
7 years ago
f206b81cf7
Sanity check skew+UBL
7 years ago
9898b96992
No lcd_map_control flag in quick_stop
7 years ago
840289e7cc
Use block cleaning instead of split flag
7 years ago
90cf6a06be
Simplify G26 user_canceled
7 years ago
cdfabbc507
Shorten error text in G29
7 years ago
c846388a65
Standardize LCD interface code for UBL a little
7 years ago
2fde60da12
Changes for parity with 1.1.x
7 years ago
6040d4080e
Cleanup stepper ISR. Allow cleaning for endstops.
7 years ago
a4e1d83599
Fix M503 S parameter
7 years ago
a3b098b4be
Whitespace clean
7 years ago
a993c5227d
Don't split first_move while homing or probing
...
While homing or probing it might be bad if the stop/trobe triggers during the first part and the second is still in the buffer.
7 years ago
5320906b0b
Update TEMP_BED_PIN in MIGHTYBOARD_REVE
...
Pin K7 number in fastio1280.h is 69, but it's also ADC15 pin.
To get correct value from ADC reading it should be set as 15.
7 years ago
aeb5c623c1
Show "Level Bed Corners" with UBL too
...
Addressing #8676
7 years ago
5fbb2f121e
Remove skew warning that could crash the planner
7 years ago
c1184552ac
Change K1 to required option PID_K1
7 years ago
9e3fbcf35c
fix for #8669 ( #8679 )
...
* fix for #8669
* Update G28.cpp
7 years ago
d8b444c144
Cleanup constextpr in planner.cpp
7 years ago
a2372cfab5
Fix SKEW_CORRECTION without leveling
7 years ago
4d3c3d0b73
Some ST7920 parity with 1.1.x
...
Possibly more should be brought over? Discussion at #8471
7 years ago
3748c28924
Fix MBL G29 without LCD
...
Addressing https://github.com/MarlinFirmware/Marlin/pull/8575#discussion_r154536617
7 years ago
772298257b
Creality pins spacing, MINIPANEL CS pin
7 years ago
b27bc67271
Set initial endstops state
7 years ago
b6ba32ce75
Support for RAMPS Plus (3DYMY)
7 years ago
53694ebaa1
Folllwup to planner splitting
7 years ago
37fff608b0
Merge pull request #8652 from fiveangle/bf2_usbcon_xonxoff
...
[2.0.x] SERIAL_XON_XOFF not supported on USB-native AVR devices
7 years ago
4b612f590c
Split first move to planner for better chaining
7 years ago
91b63f6d69
SERIAL_XON_XOFF not supported on USB-native AVR devices
...
User could enable SERIAL_XON_XOFF on USB-native devices and it would not be enabled without warning, but M115 would report the capability as available.
7 years ago
57fac33a74
add explanations
...
1) add explanations as to why software SPIs are selected
2) remove unused flag/option
7 years ago
bb23286383
add README & modify spi_pins.h
...
still trying to fix file name
7 years ago
dd8febca1a
Revert "Merge pull request #8611 from thinkyhead/bf2_planner_split_first"
...
This reverts commit 824980e70eaa7efb96bf
7 years ago
fb44f8e50f
Merge pull request #8616 from hg42/bugfix-2.0.x
...
[2.0.x][LPC1768][FIX] NUM_DIGITAL_PINS was negative, fixes PWM, arduino io functions, M42, M43, M226, probably also Servo, some LCD, soft spi, SoftwareSerial, ... may be others
7 years ago
4c5356f77a
Merge pull request #8622 from hg42/implement-LPC1768-GET_TIMER
...
[2.0.x][LPC1768][fix] Implement GET_TIMER and other GET_xxx, fixes PWM
7 years ago
f5b4e1ef4f
as a workaround enable PWM for any pin, see PR #8622
7 years ago
6e944a413c
Merge pull request #8607 from benlye/patch-1
...
[2.0.x] Fix M49 so that it does not hang the terminal console
7 years ago
967522b95e
Merge pull request #8615 from dot-bob/Duplicator_6-2.0.x
...
[2.0.x] Example configurations for Wanhao Duplicator 6
7 years ago
f4b16a3bac
Update M49.cpp
7 years ago
f9327534f8
Merge pull request #8634 from fiveangle/bf2_report_xonxoff
...
[2.0.x] Report SERIAL_XON_XOFF in M115
7 years ago
da9f140829
Merge pull request #8637 from thinkyhead/bf2_ubl_uses_LSL
...
[2.0.x] Use custom segment length for UBL Cartesian
7 years ago
3a97de52ef
Split first move to planner for better chaining
...
Address #8573 , #8595
7 years ago
24437de591
Use custom segment length for UBL Cartesian
7 years ago
4c5ffd2349
[2.0.x] Report SERIAL_XON_XOFF in M115
...
-Report SERIAL_XON_XOFF in Extended Capabilites M115 report for hosts
-Remove outdated 256 size limitation from comments on RX_BUFFER_SIZE defines
-Update error message conditions
7 years ago
aa7efb96bf
Bring configurations up to date
7 years ago
63a91cd37a
Fix a homing comment
7 years ago
8056120195
Rename inverse_mm_s => inverse_secs
7 years ago
23557f8e77
Remove obsolete de_float
7 years ago
05f8e98c4a
Fix for issue #8629 - mismatch between number of stored and loaded dummy items on non-delta machines. ( #8631 )
7 years ago
48fb4e0932
Get Bi-Linear to work with G26
...
More corrections to make that happen...
7 years ago
0850b38b45
Get Bi-Linear working with G26
...
G26 uses logic that looks like:
```
ex = _GET_MESH_X(i + 1) - (SIZE_OF_INTERSECTION_CIRCLES - (SIZE_OF_CROSSHAIRS));
```
The Bi-Linear macros need parenthesis to work correctly.
7 years ago
000b3b3117
Comment/cleanup of motion code
7 years ago
046a1ad331
Merge pull request #8625 from tcm0116/2.0.x-G33
...
[2.0.x] Fix missing return values in G33_auto_tune
7 years ago
b35c3b5eb8
Fix missing return values in G33_auto_tune
7 years ago
45c2388a58
Apply const to thermal_runaway_protection args
7 years ago
0154e3480c
New feature: BED_SKEW_CORRECTION
7 years ago
082ab8fcab
Add SKEW_CORRECTION to example configs
7 years ago
d1f11e9c10
fix missing GET_TIMER (used by PWM for Ex_AUTO_FAN)
7 years ago
dd1b503f64
fix NUM_DIGITAL_PINS being negative for more than 127 digital pins
7 years ago
bd45d0363d
Add default configurations for the Wanhao Duplicator 6.
7 years ago
91fb6231b2
Fix EEPROM V45 header, layout
7 years ago
94e6b2976e
Restore correct G26 values for gMax 1.5+ printer
7 years ago
dd3ce40826
Drop Planner::position_float, use int types
7 years ago
ec6ca37ed3
Fix (un)apply_leveling fade bug
7 years ago
a52fec6ac4
Planner class parity with 1.1.x
7 years ago
1f3ad461bc
Update M49.cpp
...
Fix M49 so that it does not hang the terminal console.
7 years ago
e37dd64548
Apply LEDColor, language fixes
7 years ago
8f90642eea
LED_CONTROL_MENU config changes
7 years ago
cf0f78336b
New Feature: LED_CONTROL_MENU
7 years ago
23e45fa3c4
Apply const to some planner vars
7 years ago
7c61bcb058
Apply SEGMENT_LEVELED_MOVES to example configs
7 years ago
ef2531558c
Add an option to segment leveled moves
7 years ago
285b868e9b
Tweak planner code style
7 years ago
1f2acc33bc
Tweaks for check_axes_activity
7 years ago
7f88334aa3
Done cleanup and removed duplicates in pins_RuRAMPS4D.h ( #8582 )
...
Remove duplicates, with followup fixes
7 years ago
a8aa43ce2d
Merge pull request #8587 from AnHardt/2_Fix_WDTO_during_long_DELTA_moves
...
[2.0.x] Fix WDTO during long delta moves
7 years ago
4793c34c53
Fix M290 boolval bug
...
Fix #8577
7 years ago
16baa48699
Fix #8579
...
Fan speed code fell into a curly brace
7 years ago
02aa93a6ad
Fix Watchdog time out during long lasting DELTA moves
...
During long lasting moves of a delta machine neither the temperatures are maintained nor buttons checked nor ... .
The fix is to call 'manage_heater()' and 'idle()' every now and then in the loop where the move is segmented.
The code is abot the same as in G2_G3 wher we had the same problem with too large circles lasting too long.
Fixing #7510
7 years ago
fadf9eb2d7
Simplify midpos calculation
7 years ago
0880031e8e
Satisfy M702 dependencies
7 years ago
0786b61ce7
Followup to #8575
7 years ago
276271e72f
Make MBL work more like PROBE_MANUALLY
7 years ago
94cb412e45
Allow override of probe bounds
7 years ago
c8718aa111
Spacing, macros in LPC1768_PWM
7 years ago
a67cf78c6b
Clean up whitespace, spacing
7 years ago
f0dd4e3fa0
Bootscreen parity with 1.1.x
7 years ago
b634bfe1b1
Tweak to readDir code
7 years ago
7be4857ab9
Tweak BLOCK_BUFFER_SIZE description
7 years ago
7d8b66e207
Merge pull request #8570 from Bob-the-Kuhn/Sbase-PWM
...
[2.0.x] MKS Sbase - add servo pin definitions and add directly controlled PWM
7 years ago
59b32c25b5
MKS Sbase changes
7 years ago
f90c075d1f
SD Menu patches
7 years ago
9b64be0bc5
Fixes for leveling sub-menus
7 years ago
25674da90c
Tweaks to do_blocking_move
7 years ago
22b897e77d
Show M211 output with workspace offset
7 years ago
d06e29846d
Loosen HAS_BED_PROBE definition
7 years ago
e48fcad615
change G26 and G29 bit function names to avoid HAL collision
7 years ago
41ec449960
Fix G26 error return
7 years ago
9badf5dc0d
Fix Micromake C1 config
7 years ago
7576ad7fc2
Merge pull request #8554 from tcm0116/2.0.x-cleanup
...
[2.0.x] Fix for #8525 and other cleanup
7 years ago
27c5692b13
Syntax tweaks
7 years ago
d18d40e1d6
M290 report on change, P0 to leave Probe Z Offset alone
7 years ago
65f365333f
[2.0.x] G33 probe error handling
7 years ago
8c69adba8b
Merge pull request #8553 from Bob-the-Kuhn/2.0.x-U8Glib-follow-up
...
[2.0.X] U8Glib follow up
7 years ago
be00e421a7
Patch up M290, M851
7 years ago
fc40d56131
fixed error, updated defaults, added notes
...
Travis fix - only allow ultralcd_st7920_u8glib_rrd_AVR.cpp to compile when ST7920 selected
7 years ago
d29cb646e3
Fix erroneous reference to temperature in time calculations
...
Travis is having problems at: https://github.com/MarlinFirmware/Marlin/pull/8560
So... doing a direct commit to get things correct. Bugfix_v1.1.x does not have this bug. Nothing needs to be done to that branch.
7 years ago
7bb1721f35
Fix _BV already defined warnings for Teensy
7 years ago
5f9592a523
Cleanup narrowing warning in pin_is_protected
7 years ago
34eaaab5fb
Fix _BV already defined warnings
7 years ago
2ea779e560
Allow bed probe sanity checks to run
7 years ago
d24b1190bd
Don't use Z_MIN_PROBE_ENDSTOP on DELTA
7 years ago
e34c6827ea
Init MIXING virtual tools as switching
7 years ago
a9ecb975b2
Apply LINEAR_UNIT to M503 output for M200
7 years ago
d95ee0f003
Merge pull request #8551 from revilor/bugfix-2.0.x
...
MK2_MULTIPLEXER does not require E2/E3 stepper pins
7 years ago
80ada58818
One fewer function call in probe_pt
7 years ago
92a0dc552a
MK2_MULTIPLEXER does not require E2/E3 stepper pins
7 years ago
b49acce035
Tweaks for lcd_external_control
7 years ago
1ef1052ae1
Phatter arrows for Z offset overlay
7 years ago
5926c9c97b
Followup for MESH_EDIT_GFX_OVERLAY
7 years ago
ab03a31cc9
Patch G0/G1 for NANODLP_Z_SYNC
7 years ago
a766dfb3b1
Merge pull request #8536 from thinkyhead/bf2_nanodlp_z_move_sync
...
[2.0.x] Implement NANODLP_Z_SYNC for 2.0.x
7 years ago
01e207213f
Fix MK2_MULTIPLEXER stepper indirection
7 years ago
ec04cf27d3
Fix the G26 out of scope identifiers in the v2.0.0 branch ( #8543 )
...
These changes may need to be warmed over. I tried to fix things with
the least amount of disruption. I just wanted to get the bugfix_v2.0.0
branch working for people again.
7 years ago
dc82babe8e
Implement NANODLP_Z_SYNC for 2.0.x
7 years ago
c6b0c104bb
Adapt G26 to work for all meshes
7 years ago
5ce7f23afa
Config option G26_MESH_VALIDATION for all meshes
7 years ago
c19eb33408
Move G26 to gcode sub-folder
7 years ago
a03f93bab4
Fix fan kickstart
7 years ago
9e3c41f9e8
Tweak fan kickstart / speed code
7 years ago
118ac61e59
[2.0.x] Tool change bad behaviour fix
...
Previous fix did not work as expected when axeis not homed. It raise Z but never return to original position
7 years ago
c35d27f77c
Merge pull request #8299 from tcm0116/2.0.x-BIQU_BQ111-A4
...
[2.0.x] Add BIQU BQ111-A4 board
7 years ago
1685cd193b
Tweak char_mode init
7 years ago
9406c87a97
Fix up LCD init / charset
7 years ago
fa577392b2
Add BIQU BQ111-A4 board
7 years ago
c2fc78c3a8
#ifndef => #if !PIN_EXISTS
7 years ago
c613a1ed38
Fix indentation, stepper.h dependency, etc.
7 years ago
f011a32771
Board definitions for Ultratronics Pro v1.0
7 years ago
9dad534f02
fixed
7 years ago
4371345cbe
Don't re-init graphical LCD after boot screen
...
Followup to 13a3fb1acc
7 years ago
56c02b7f59
Shift register buttons question
...
Can LCD shift registers keep up with faster MCUs?
7 years ago
3994d3b935
General cosmetic LCD
7 years ago
617993d0ea
Patch for !!TEST (was _BV once?)
7 years ago
3269d8dd62
Tweak M42 var
7 years ago
bb1a6eea88
Remove pin count check for MIGTHYBOARD_REVE
...
Remove assert and unused code since it is implemented in pinsDebug_plus_70.h
7 years ago
1ce0fb336b
Patch Max7219_LED_Set input args
7 years ago
a61127a421
[2.0.x] tool change bad behaviours
...
This will solve 2 issues on tool change.
1) when no home is done ("no_move" is set) tool change should never move X & Y because... I don't know where I am...only Z should be adjusted to avoid bed collision if other nozzle is lower than current.
Since no move no bed level matrix should be applied
2) When SWITCHING_NOZZLE is enabled and system is homed there are two movements to go to destination, but first can move Z to older position and then crash on the bed
7 years ago
e2724c68ab
Update pins_RURAMPS4D.h
...
Add and bugfix pins
7 years ago
9770062309
Merge pull request #8463 from thinkyhead/bf2_32bit_M42
...
[2.0.x] Updates to Anet A8 configurations
7 years ago
3066655727
Try port*100+pin, fix config dependency
7 years ago
ba8bc7ea80
Cosmetic tweaks
7 years ago
f409147116
Fix P2_04, P2_05
7 years ago
a28ccabe2a
M42 P1.20 fix
7 years ago
33912fa7e8
Update Temperature::setPwmFrequency prototype to match source
...
Introduced with #8446
7 years ago
b9327a4d16
Misc. general cleanup
7 years ago
8836623e0f
Fix `sq`/`min`/`max` macros after platform headers
7 years ago
fe4f009fdd
32-bit unless…
7 years ago
25af9decfe
Remove enum.h include of MarlinConfig.h
7 years ago
1d4571b88d
Dependency adjustments
7 years ago
550f1025f0
Try using <Arduino.h> everywhere
7 years ago
c0000a0cdc
Move servo code to modules/servo.*
7 years ago
81bc428b48
Don't compile custom u8g without DOGLCD
7 years ago
c14000775b
PWM fixes, slow down fan update
...
include LPC1768 syntax for M42
couple more pin_t changes
consistency
change M42 to R, P format
Revert "change M42 to R, P format"
This reverts commit 01f12f579ec9ccc1bb9126e68d2c86449e9b7edf.
7 years ago
60adc6ff02
Display filwidth ratio in terms of E mm
7 years ago
6e533748eb
Fixes #8472
7 years ago
485abb023b
Merge pull request #8456 from thinkyhead/bf2_wednesday_tweaks
...
[2.0] No retroactive adjustment with M851 Z
7 years ago
3bba7d60f3
No retroactive changes with M851 Z
...
If using babystep to adjust the Z probe offset, the axis will move and the mesh will be updated at the same time, causing a doubling of the Z offset over the rest of the print.
To correct for this, the current Z position would need to be modified in the opposite direction, canceling out the additional Z offset added to the mesh. This would be confusing to users, and moreover it would not be accurate without also taking the current Z fade level and current Z height into account.
It might make sense to change the mesh in the case where no babystepping is taking place, but this could be considered an undesirable side-effect of changing the `zprobe_zoffset`.
One way to remedy this would be to return to storing the mesh with `zprobe_zoffset` included, then subtracting `zprobe_zoffset` from the returned Z value. Thus, a babystep moving the Z axis up 1mm would subtract 1 from `zprobe_zoffset` while adding 1 to all mesh Z values.
Without including the `zprobe_zoffset` in the `z_values` there is no safe way to alter the mesh in conjunction with babystepping, although it's fine without it.
7 years ago
32512332df
Apply some formatting
7 years ago
7dacc999b9
Remove obsolete show_bootscreen var
7 years ago
9729528d13
Update UBL's Delta Probable locations
...
This is a non-intuitive change. @oldmcg says in this post https://github.com/MarlinFirmware/Marlin/issues/7572#issuecomment-340641207 that using DELTA_PRINTABLE_RADIUS is better than DELTA_PROBABLE_RADIUS for setting the probe limits. This is because the automatic probe code checks all locations for being reachable by the probe prior to doing the probe.
7 years ago
d48cb6bf41
Apply coding standards to Max7219
7 years ago
bd8bcf06e7
Updates to Anet A8 configurations
...
Based on #8426
7 years ago
7eea000f4b
E0 auto fan fixes
7 years ago
b2dda096fe
Fix FILAMENT_LCD_DISPLAY for disabled state
7 years ago
1e8afb66b7
Fix a planner comment
7 years ago
50f09cc029
Miscellaneous cleanup
7 years ago
63257dc083
Fix M503 output for M145
...
Fixes #7978
7 years ago
0918dae66e
Add OV() macro for use in thermistor tables
7 years ago
24057270a3
Merge pull request #8420 from RowanMeara/rm-dithering-2.0.x
...
[2.0.x] Fix Software Fan PWM
7 years ago
5079a02c90
Add HAL_SERVO_LIB to HAL_Due.h
7 years ago
9c3761047e
Merge pull request #8434 from thinkyhead/bf2_fix_M32_subroutines
...
[2.0] Fix 'M32 P' subroutines
7 years ago
e0d367f1fb
Fix M32 P subroutine handling
7 years ago
9f8b4c5ee8
Patch SD lib files for readability
7 years ago
2c8c30437e
Fix parser parameter value handling
7 years ago
6131533157
Change dithering behavior to intended.
7 years ago
e70b44dc0b
Make sure leveled[] is defined for later use
7 years ago
54774841ba
Merge pull request #8416 from thinkyhead/bf2_M114_DETAIL
...
[2.0] Add M114_DETAIL to Configuration_adv.h
7 years ago
009e3a7aa7
Add M114_DETAIL to Configuration_adv.h
7 years ago
6d6c3b1e97
Fix up REPRAPWORLD_KEYPAD defines
7 years ago
3f0a982b8c
Move Filament Width Sensor to Configuration_adv.h
7 years ago
b76e173205
Move test extrusion options under G26
7 years ago
14ebedca27
Drop unused LARGE_FLASH option
7 years ago
b7feb53e8a
Support for Extrudrboard in Printrboard Rev.F
7 years ago
91baca6abb
Patches for compiler warnings/errors
7 years ago
2f73dec077
Apply native workspace fixes for G92, G53-59
7 years ago
04abd8d459
Improve and clarify M428 code
7 years ago
c009a990e4
[2.0.x] Fix some 8-bit Teensyduino compile warnings ( #8385 )
...
* Fix some 8-bit Teensyduino compile warnings
-Override Teensyduino legacy NOT_A_PIN 127 define
-some fixups for Printrboard_RevF pins
* Proper cleanup of Printrboard Rev.F pins
* Apply LCD fixes to Printrboard v1
7 years ago
e8e92f8969
No leveling data in M114 if no leveling is enabled
7 years ago
f5d210c35c
Fix report_current_position
7 years ago
faaae7a1b2
Provide more clearance for BL-Touch probe
7 years ago
06ee6584fd
Remove offsets from soft endstops, tool change
7 years ago
Roxy-3D