29b456ae07
Suppress some compiler warnings
9 years ago
23d742bf06
Don't free the stack array plane_equation_coefficients (PR#83)
9 years ago
e3b1e08777
Patch G30 to use raise_z_for_servo (PR#73)
9 years ago
a1eb90d5c0
Save another 30 bytes in gcode_SET_Z_PROBE_OFFSET
9 years ago
91122277f4
Reduce gcode_SET_Z_PROBE_OFFSET by 88 bytes
9 years ago
5707a2c3d5
indexindexIntoAB is only vald for !DELTA
9 years ago
d8860f9ad9
Alway end at the same point
...
Always end at [RIGHT_PROBE_BED_POSITION, BACK_PROBE_BED_POSITION]
Regardles the evennes of auto_bed_leveling_grid_points.
9 years ago
4ca8f4a9a7
Always zigzag
...
Use the shortest way between probing-points.
9 years ago
3d23424121
Add array indexIntoAB[xx][yy]
...
and use it.
9 years ago
e2d69f66b2
Make Z_PROBE a Z_MIN_PROBE (PR#65)
...
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.
Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX check for the probe in update_endstops().
Using an delta related idea of @clefranc from #61 ,
extended to the general change for all setups.
Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
9 years ago
6a6e863a47
Resolve #2581 by adding a missed ';' (PR#67)
9 years ago
e09ff79635
Update pins_RAMPS_13.h (PR#64)
...
Now all ramps configuration can enable Filament sensor not only EEB
9 years ago
e6aed7bb4e
Update thermistortables for Hisens Thermistor (PR#2588)
9 years ago
9d8cc24abf
Continue from the line following the M999 (PR#60)
...
If the printer is going to accept the M999,
then it should continue from that line number.
9 years ago
f3ab1dba54
Z babystepping for coreXY (PR#47)
...
only X and Y were not implemented
9 years ago
35afea1c0e
Restore test
...
PR#2572 Changed this because of faulty Boolean Logic
NOT(A OR (NOT B) OR (NOT C)) !=
(NOT A) AND ((NOT B) OR C))
Besides, the compiler should be smart enough to
optimize this without help from the programmer
9 years ago
6af75f4b5d
Squish down deprecated tests in sanity check
9 years ago
edeb58288e
Use PIN_EXISTS in sanity check
9 years ago
c30b7693e0
Clean up RUMBA pins conditions
9 years ago
46453905d6
Apply remaining ENABLED/DISABLED conditionals
9 years ago
b227d8c128
Supply a VERSION in a short form for displays
...
The long descriptor will still be available in M115
9 years ago
cd7828a928
This will be the 1.1.0 Release rather than 1.0.3
9 years ago
4e2f5618c1
Pick up Default_version when needed
9 years ago
329acc852e
Canonize Option flag USE_AUTOMATIC_VERSION
9 years ago
5a11d32a85
Move deprecation test to SanityCheck.h
9 years ago
7bb7a52940
Bring config up-to-date
9 years ago
244ea2014a
Boot-screen for text-displays improvements
...
Centred the logo for 16x4 and 20 x4.
Moved version to the bottom line
Code shrink to 704 bytes.
9 years ago
80f2a20842
Enable bootscreen in all Configurations
9 years ago
2684d061ed
Scroll too long strings on bootscreen
9 years ago
4f46df5dab
Make bootscreen configurable for the graphic displays
...
Saves about 473 byte of progmem and 28 bytes of RAM.
9 years ago
09571b7753
Boot-screen for the character displays
...
Uses about 488 byte of progmem and 32 byte of RAM.
For that configurable.
9 years ago
866efc14fe
Add Danish translations
9 years ago
267f3479d7
Adjust spacing in pins_RAMPS_13.h
9 years ago
56702e7bb9
Define servo pins just like other pins
9 years ago
4b9d5cd352
Use lowercase names for serial instances
9 years ago
1e2deff4fd
Rename BTENABLED to BLUETOOTH
...
- For some reason it’s easy to forget what BT stands for, but it
doesn’t need an abbreviation.
9 years ago
68055a5959
Include RIGIDBOT_PANEL in Conditionals
9 years ago
f8ed3a835d
Added comment with the RigidBot Big bed size
9 years ago
7deae6b6be
Updated RigidBot example configuration
...
- The default serial baud rate of 115200
- The regular RigitBot bed size 254mm/248mm/254mm
- Single stock extruder
- Stock termistors for extruder and hotbed
- Stock Min X/Y/Z stops. Max stops not connected
- Stock 32 teth tooleys (stock axis steps)
- No auto bed leveling
- No screen
9 years ago
5418faa1f9
Add sanity checks for old names
9 years ago
f03e063750
Rename BEEPER to BEEPER_PIN
...
For consistency with other pins, allowing use of `PIN_EXISTS` macro.
9 years ago
270c766de2
SDCARDDETECT -> SD_DETECT, added docs
...
- `SD_DETECT_PIN` replaces `SDCARDDETECT`
- `SD_DETECT_INVERTED` replaces `SDCARDDETECTINVERTED`
- Revise the description of `SD_DETECT_INVERTED`
- Add a note about the override of `SD_DETECT_INVERTED` in
`Conditionals.h`
9 years ago
496fc28dc3
Tweaks to pins comments
9 years ago
8d3b74cc6e
Rename SDCARDDETECT to SDCARDDETECT_PIN
...
- Rename the pin so it can be tested with `PIN_EXISTS`
- Fix some incorrect tests for `SDCARDDETECT`
9 years ago
0f5ada8cbd
Group the fail case in one negation (PR#2572)
9 years ago
7ddf1cda1d
Improve condition for SERVO_LEVELING (PR#2570)
9 years ago
f32048b8f5
In for a penny, in for a pound
9 years ago
e944f960de
Add a sanity check for old name "BEEPER"
9 years ago
8ebf0b92be
Spacing adjustments in some pins files
9 years ago
94a796c8cc
Rename BEEPER to BEEPER_PIN
...
For consistency with other pins, allowing use of `PIN_EXISTS` macro.
9 years ago
b217474eab
Compiler Complaints about concatenated tokens (PR#2566)
9 years ago
2460f82d8b
Make proper distinction between BEEPER and HAS_BUZZER
9 years ago
58cfcd4239
Overridable Options - Part 5
...
Apply `ENABLED` / `DISABLED` macros to files needing only a small
number of changes.
9 years ago
5e834352a9
Overridable Options - Part 11 (PR#2563)
...
Apply `ENABLED` / `DISABLED` macros to EEPROM-related files.
9 years ago
bf6eb93c61
Overridable Options - Part 10 (PR#2562)
...
Apply `ENABLED` / `DISABLED` macros to planner files.
9 years ago
51e89a269c
Overridable Options - Part 9 (PR#2561)
...
Apply `ENABLED` / `DISABLED` macros to temperature-related files.
9 years ago
c35fb88094
Overridable Options - Part 8 (PR#2560)
...
Apply `ENABLED` / `DISABLED` macros to stepper-related files.
9 years ago
0d8989fc14
Overridable Options - Part 7 (PR#2559)
...
Apply `ENABLED` / `DISABLED` macros to LCD-related files.
9 years ago
b4abb0ae7f
Apply ENABLED / DISABLED to Marlin core files (PR#2558)
9 years ago
c0d7ea3e7e
Overridable Options - Part 4 (PR#2556)
...
Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files.
9 years ago
4b40964064
Overridable Options - Part 3 (PR#2555)
...
Apply `ENABLED` / `DISABLED` macros to language-related files.
9 years ago
32683b282b
Include configurator copies of configs
9 years ago
37d1879386
Apply overridables to Configuration files
9 years ago
9d151bb61b
servo_endstop_angles -> servo_endstop_angle
9 years ago
9334479aeb
Minor cleanup of Conditionals.h
9 years ago
1f63293624
servo_endstops -> servo_endstop_id
9 years ago
edaaead7e0
Fix comment about SERVO_ENDSTOP_ANGLES
9 years ago
ed4a6371ad
Add HAS_SERVO_ENDSTOPS to simplify conditonals
9 years ago
70be61d416
Reset filament_size with a loop
9 years ago
ae9274be05
Fix minor compiler warnings in for loops
9 years ago
c7c8cfed6f
Complete M200 output with M503
...
- The contents of EEPROM include filament diameters even with
Volumetric disabled. This change makes `M503` display the full
volumetric settings so that playing back the output of `M503 S0` will
fully restore them.
9 years ago
4a58e447a1
Add array size to servo_endstop_angles (PR#2553)
9 years ago
a0ae9e30df
don't pass integer by reference, inefficient. (PR#2547)
9 years ago
d03f037a92
Get rid of malloc() and free() (PR#2549)
...
Just the minimal changes to qr_solve.cpp and .h to get rid of malloc() and free().
Saves about 656 bytes of progmem (library-code)
and 22 bytes for static variables.
Should use exactly the same amount of stack as it did before on the heap.
9 years ago
3b2b2313ff
Combine if block related to SERVO_ENDSTOPS
9 years ago
0af2a80e06
Make SERVO_ENDSTOP_ANGLES 2-dimensional
9 years ago
525d0dc239
Configurator is out-of-date AGAIN (PR#2550)
9 years ago
dd22cbbfb8
makefile: add buzzer.cpp (PR#2479)
9 years ago
9f48798ffd
Replace ENABLED with DEFINED for SERVO_ENDSTOPS (PR#2542)
9 years ago
ae00fad75b
Rename as M100
9 years ago
a401d738df
There is an echo in here
9 years ago
ed7d45e8f5
Memory watcher
9 years ago
d17f7ebc8a
Multiply WATCH_TEMP_PERIOD by 1000UL (PR#2535)
...
instead of 1000. Else we get errors with times over 32 seconds.
9 years ago
bea6739774
Don't include Z_RAISE_AFTER_PROBING if not used (PR#2527)
9 years ago
81bba7ed88
More sanity checking for extruder requirements (PR#2531)
9 years ago
87a97f3724
Fix conditions for display strings
9 years ago
aaccea0260
Shift some display only strings from language.h to lenguage_en.h
...
and translate them to German.
9 years ago
e4c01f1c7e
Simplify init with ARRAY_BY_EXTRUDERS1 macro (PR#2507)
9 years ago
ab6f1fdf8b
Move & document ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED (PR#2528)
...
As suggested in #2521
- Move `ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED` because `SDSUPPORT` is
also required.
- Add a note that endstops must be enabled for the feature to have any
effect
9 years ago
1183c10a2e
makefile: drop -q -q (much quiet) from avrdude flags
...
Annoying when trying to figure out if uploading
actually does something.
9 years ago
0e064357f4
makefile: use /etc/avrdude/avrdude.conf on linux
...
No need to look for arduino specific avrdude configuration
as distributions ship their own avrdude.conf file that
is compatible with arduino.
9 years ago
bcb7d5a149
Improve sanitycheck for TEMP_SENSOR_1
9 years ago
5b24f59401
Add sanity checks for temp sensors
9 years ago
fd0e81b0c7
Distinguish between BUZZER and SPEAKER (PR#2513)
...
A speaker needs a AC or a pulsed DC to make a sound, a buzzer only needs a DC.
A buzzer has it's own resonator. It works in most cases to feed the buzzer with a pulsed DC, but the sound will not be as loud as with pure DC.
There seem to be boards where the BEEPER-pin is not able to handle a PWM. Obviously intended for a buzzer.
To make these board able to handle a speaker
* replace the PWM based tone()-function again with a on-delay-off-delay loop.
Hopefully the last time I touch the beeper code.
9 years ago
e2957df05c
Shorthand for do_blocking_move_to
9 years ago
819c5b9b50
Adjust comment on Z adjustment
9 years ago
5a7356b6fc
Patch for G29 final Z position
...
Include all the necessary pieces to get the final Z position after
probing the bed, and add commentary about other possible changes.
9 years ago
088e09e052
Add forgotten Marlin_main.cpp
9 years ago
8b876241bd
Some more servo code tweaks
...
Just set up the pin. Don't move to a random position.
Simplify servo::move()
* servo::move() does not need the pin parameter - The pin is set during servo_init() with attach().
* servo::move() does not need a return value.
SERVO_LEVELING is the wrong condition to deactivate the servos.
Remove some temporary (Servo *) variables.
SanityCheck for the servo indexes.
9 years ago
b116c096bd
Reduce set_homing_bump_feedrate, save 42 bytes (PR#2512)
...
Updates to `set_homing_bump_feedrate`:
- Move the string into Program Memory, reduce length by 31 bytes
- Use an auto to get the divisor, adjust it on error
- Set feedrate once, at the end
9 years ago
f7e7862588
Better Sanguinololu & Graphical Controller (PR#2504)
...
- Change suggested at
https://github.com/MarlinFirmware/Marlin/issues/2482#issuecomment-123553
266
9 years ago
a1154d4a20
Enable Y and sanity-check CoreXZ (PR#2509)
9 years ago
932f1c109e
Move servos to the top in pins_MEGACONTROLLER.h
9 years ago
90f8ddfc1e
Apply MINIPANEL to other configs
9 years ago
00dbf69b6d
add MINIPANEL defines
9 years ago
8ac5e56934
fixed some format problems and cleaned code
9 years ago
eef595aa64
add makerlab mega controller pin configs
9 years ago
4e14e152fa
Add Travis tests for CORXY and COREXZ
9 years ago
27d7d2ccab
Correct bracketing for COREXY-XZ
9 years ago
469843427d
Reduce code in gcode_M81 (PR#2497)
9 years ago
c66955aaf9
Mark unchanging arrays as const (PR#2494)
...
The compiler may be able to optimize if it knows an array won’t be
changing.
9 years ago
278aa15301
Add COUNT macro and apply
9 years ago
d85861d296
Move macros, add ENABLED/DISABLED, add includes
9 years ago
17960fd2b0
Neaten up pins_MEGATRONICS.h (PR#2493)
9 years ago
aac2b9aa9d
Reduce code in gcode_M84 (PR#2492)
...
`gcode_M84` only needs to call `finishAndDisableSteppers`, which calls
all the other functions.
9 years ago
4971fa73f9
Add a sanitycheck error for old servo settings (PR#2491)
...
- Documentation solution for #2476
9 years ago
96ace72ddc
Servos attach/detach based only on servo config
...
Assuming #2470 fixed up the main issue.
9 years ago
b80a6a8d31
Correct Kossel Pro Configuration_adv (PR#2473)
9 years ago
000a6fce46
Extract update_endstops from stepper ISR (PR#2474)
9 years ago
e83eac312e
Move plan_arc next to prepare_move
9 years ago
5c5936508d
G2/G3 Arcs for Delta
...
- Update prepare_move_delta to take a target argument
- Add Delta support to plan_arc
9 years ago
9f53e2f0c9
Implement COREXZ in stepper.cpp and planner.cpp
9 years ago
fa00e1d97f
Explode conditions common to corexy and cartesian
9 years ago
c7dd5527b4
Add a C_AXIS and Z_HEAD to support COREXZ
9 years ago
129f986ccf
Add COREXZ option to configurations
9 years ago
69b0490b77
Show minimal preheat options in menus (PR#2471)
9 years ago
eacfe132aa
Change the name of servos[] and servo_t
9 years ago
3b23ccd366
Patch servos code for move
...
- Have `Servo::attach` explicitly return -1 if it fails
- Check for -1 in `Servo::move` because `servoIndex` might be 0
- Make `attach` / `detach` calls conditional on `SERVO_LEVELING`
- Move `SERVO_LEVELING` define to `Conditionals.h`
9 years ago
54ddc1d417
Simplify DRY RUN (PR#2358)
...
Elsewhere DRYRUN turns off the heating elements
and ignores constraints on them.
Here, whenever motion is entered into the planner,
if DRY RUN is set, we instantly act as if the E_AXIS
is in the desired final position.
9 years ago
944090c19c
Optimize lsDive logic
9 years ago
417706e578
Include space for the terminating nul in lsDive
9 years ago
f3c1a6b19c
Reduce lsDive stack usage to the minimum
9 years ago
fba4e6241b
Specify print format for reporting invalid tmp_extruder (PR#2465)
9 years ago
d15d869267
Rename axis_is_at_home() to set_axis_is_at_home() (PR#2464)
...
to make clear - it's not a question but an order.
9 years ago
f209b755a5
Move the Z probe as far as needed to trigger the switch (PR#2461)
9 years ago
0f1df62389
Fixup comments in code_seen
9 years ago
2945eb6650
Call code_seen only once per parameter
9 years ago
b742af2e2a
Move Y_STOP_PIN for Printrboard with SD (PR#2420)
9 years ago
baa9199973
Define extern delta only for delta
9 years ago
77e80ef367
Require extruders for thermal code
9 years ago
3bde4f4855
Require temp sensor for bed thermal protection
9 years ago
82a3ed2f9a
Cleanup and dev notes in Marlin.h
9 years ago
db23b9b184
Minor tweak to M204 code (PR#2457)
9 years ago
81d42406b7
Move braces in homeaxis to prevent a hanging else (PR#2451)
9 years ago
552a327df8
Fix lsDive filename stack overrun (PR#2449)
9 years ago
a6628f12cc
Eliminate the further use of the pin-parameter
9 years ago
8504992e9f
Remove the additional pin variable in Servo.cpp
...
as sugested by @c-born
inhttps://github.com/MarlinFirmware/Marlin/issues/1885#issuecomment-92618240
9 years ago
ed6598adf5
Corrected Bed Height vs. Bed Topology for verbosity > 3
...
and cleaned out some tabs.
Everything else is a rebased PR#2017 as proposed by @CptanPanic
9 years ago
62302ceb9e
Add calculation of difference between auto-correct bed level plane, and measured topo map.
9 years ago
de25a48dec
Remove PID examples from preconfigured configs
9 years ago
7456710a1f
Update configs formatting
9 years ago
391386dd94
Update configs for new servo deactivation
9 years ago
5243d8b523
Deactivate DEACTIVATE_SERVOS_AFTER_MOVE by default
9 years ago
49609f6c14
Activate the new servo.move() function
...
by replacing the sequences (attach, write, delay, detach), and their conditions with the new function in Marlin.main.cpp
and removing the old configuration in the ABL part of Configuration.h
9 years ago
40b6edcad7
Introduce DEACTIVATE_SERVOS_AFTER_MOVE in Configuration.h
...
DEACTIVATE_SERVOS_AFTER_MOVE is ought to replace PROBE_SERVO_DEACTIVATION_DELAY.
But it will work on all servo moves, not only the probe servo moves.
9 years ago
2ddb2a2be9
Add Servo::move() to servo.cpp
...
move(pin, angel) - Sequence of attach(pin), write(angel),
if DEACTIVATE_SERVOS_AFTER_MOVE is defined waits SERVO_DEACTIVATION_DELAY, than detaches.
As we have jitter on the servos during moves of the steppers, and detaching them improves this behaviour,
the usual sequence to handle a servo movement is:
attach(pin)
write(angel)
delay(until the servo finished the move)
detache()
Here a function to handle the complete sequence.
9 years ago
8a01e5fb7a
Update Russian translation (PR#2443)
...
Slightly updated translation.
9 years ago
e83575537a
Compiler defines USBCON for USB devices (PR#2433)
9 years ago
7268d46508
Always calculate extruder temperature PID d term (PR#2432)
9 years ago
87a872e103
Use st_get_position_mm where possible (PR#2411)
9 years ago
2e0da8abdc
Allow N to take a negative argument (PR@2402)
9 years ago
447dbd6fa5
Add STEPPER_RESET_PIN support
9 years ago
a0351bdb73
Remove STEPPER_RESET_FIX option
9 years ago
6b1b8cb2b3
Also nullify spaces before the checksum asterisk (PR#2409)
9 years ago
8e61314323
Use RIGIDBOT_PANEL for consistency with online docs
9 years ago
4b204da3c1
Cleanup of pins_RAMPS_13.h
9 years ago
536f86e896
RigidBot CONTROLLERFAN_PIN in Configuration_adv.h
9 years ago
f068e46661
RigidBoard include for pins.h
9 years ago
9ebcae496d
RIGIDBOARD / RIGIDPANEL
9 years ago
c3c605c658
Move note about LiquidTWI2 to Configuration.h (PR#2406)
9 years ago
4e9d658141
Prevent a hanging SERIAL_ECHO_START in M111
9 years ago
bc0fdbe88e
Use SERIAL_EOL in SERIAL_PROTOCOLLN macros
9 years ago
d78ebbc0e9
Remove unused MSG_OK_B and MSG_OK_T
9 years ago
6b494c1535
Use disable_all_heaters in M111
9 years ago
15190d40df
Add extra EOL after M111
9 years ago
0e1cf78f5c
Remove code for testing if probing range is too small (PR#2390)
...
becaue it is over-restrictive and superseeded by the now working tests
if the probe-recktangle can be reached. See iss#2366
9 years ago
d421f5250d
Correct the sign of zprobe_zoffset for G29 (PR#@391)
...
Sign flipped with #2167 .
See also comments
https://github.com/MarlinFirmware/Marlin/issues/2040#issuecomment-118568355
and following.
9 years ago
52fcc743ab
Replace "target" with "destination" in M600 (PR#2374)
...
- Also fix a bug in `M600` where `Z_MAX_ENDSTOP_INVERTING` is being
used as the index into the `destination[AxisEnum]` array.
10 years ago
a5033c3652
Enable LCD_PIN_RESET if it exists (PR#2375)
10 years ago
23c8c5348f
Z-height fix V2b (PR#2351)
...
here the other two occurences of `Z_PROBE_OFFSET_FROM_EXTRUDER` are
replaced with `zprobe_zoffset`.
10 years ago
a111fbbd0a
z-probe offset fix (PR#2361)
...
verified via 1.0.2 tag that compiles by multiple people,
credit for the fix goes to paulusjacobus for the initial find and
sniffle for the correction so M851 works.
10 years ago
42465ee444
Cleanup of comments & spacing
10 years ago
9682ed455e
Fix comment on M83, add comment to prepare_move
10 years ago
bb44fe17cf
Fix typo in buzzer.h endif (PR#2337)
10 years ago
36746143a1
Correct output of M48 (PR#2336)
...
n_samples is an uint8_t .
Got printouts like:
50 of 2 ...
10 years ago
f6ca5a8da8
Allow "M110 N123" without a checksum
10 years ago
aaad65ff5d
Include a comment documenting M110
10 years ago
862c72b030
Put the mandatory test of gcode_N first
10 years ago
30976f9773
Allow M110 to handle a second N argument
10 years ago
d135b15bb8
Init all endstop bits to 0 (PR#2332)
10 years ago
5ccb1c9e7d
Use millis for M600 audio feedback interval
10 years ago
fb16a83b8a
Cleanup M600 documentation comments
10 years ago
97ec224d72
Replace target with destination in M600
10 years ago
4ce9ddbb74
Check the temperature before filament change
10 years ago
b8b5762e55
Update Ultimaker URL
10 years ago
d5bfbf5a59
Added correct dutch translation for calibrate.
10 years ago
149c474e55
Updated Russian language (PR#2325)
...
Gleaned from
https://github.com/MarlinFirmware/Marlin/commit/4ac14a7e5fa8e6e395436664
8976eafd1ae220ae
10 years ago
722829b058
Move buzzing code to buzzr.h & buzzer.cpp (PR#2307)
...
at least the lcd independent part from Marlin_main.cpp.
10 years ago
c461975140
Rename and repair MELZI_1284 (PR#2301)
...
to MELZI_MAKR3D.
Fix for #2288
As the normal MELZI also can have a 1284.
10 years ago
1e9cf905c7
Enable ZigZag AutoBedLeveling on Deltas (PR#2273)
...
ZigZag has been disabled by fault due to do_topography_map
10 years ago
ec93383ec8
Add SanityCheck for bed probe position settings (PR#2282)
10 years ago
dc40a5f6e0
Patch up more outdated config lines
10 years ago
98c9111a7d
Update delta configs with latest settings
10 years ago
e6baf8afd9
Fix up allen key settings in delta configs
10 years ago
3b293fc5d1
Move Delta settings lower in delta files
10 years ago
df21857583
Move extruder offset settings next to extruders setting
10 years ago
2dd1859247
Cleanup spaces and comments in configs and conditionals
10 years ago
a274769f4f
Clean up spacing and comments
...
Also clean up some trailing spaces in a few other sources
10 years ago
d3bce05d54
Fix up spacing for filament sensor values
10 years ago
b4b10a57fe
Fix configurator section directives and values lists
10 years ago
bba14dcbe6
Move Z Safe Homing point to the middle of the movement range
10 years ago
318318b02f
Add pins_RAMPS_13_EFB.h to reduce redundancy
10 years ago
346c8b339b
Remove a test from pins_RAMPS_13.h
...
- Add 3 new lines to `pins.h` to remove 2 redundant tests in
`pins_RAMPS_13.h`
10 years ago
b93cddfcc9
Add lost MKS_BASE to pins.h (PR#2297)
10 years ago
6ab7b560af
Rework buzzing (PR#2296)
...
by:
Moving HAS_LCD_BUZZ macro to Coditionals.h
Renaming HAS_LCD_BUZZ to HAS_BUZZER to make clear is has nothing to do with the lcd.
Removing the ULTRALCD condition.
Moving declaration of lcd_buzz() out of the ULTRA_LCD block in ultralcd.h
Moving definition of lcd_buzz() out of the ULTIPANEL block in ultralcd.cpp
Renaming lcd_buzz() to buzz() to make clear is has nothing to do with the lcd.
All buzzing code is now only dependent on the existence of a BEEPER-pin or the definition of a LCD_USE_I2C_BUZZER.
To do: Check the conditions for the BEEPER-pin in all pin-files.
10 years ago
29122db2fa
Fix ULTRA_LCD spelling in HAS_LCD_BUZZ
10 years ago
1d94d098bf
Formatting tweaks as part of fixing issue 1497
10 years ago
e602c28ad9
Set auto fan pins to OUTPUT during init
...
Fixes the problem of these pins being left in INPUT state, as described
in #1497
10 years ago
90f858aa85
Use translated strings for axis movement (PR#2280)
...
Suggest we use the translated strings here. They use (except for
German) the phrasing “Move X” instead of just the axis letter, but they
should fit the available space. The “Extruder” string would be the
same, except it will be translated.
10 years ago
e2a4a83586
Don't re-apply Z_RAISE_BETWEEN_PROBINGS in probe_pt (PR #2281 )
10 years ago
6b1b3adaf0
Consistent punctuation in SanityCheck errors (PR#2283)
10 years ago
eb81982fcd
Fix error next command in autotune (PR#2274)
...
Now send only temperature for T or B, but not send OK.
Host interprets the line to show the right temperature, but not in
response to M105 then stop and send commands until it ends the autotune.
10 years ago
55b23c896a
Optimise out_of_range_error() (PR#2265)
...
by avoiding the strncopy()
10 years ago
b0860adab6
Fix volumetric multiplier display for filament sensor (PR#2264)
...
The volumetric multiplier display needs to be multiplied by 100 in order to make it an integer for display purposes.
10 years ago
45642b7fe8
Respect DISABLE_AXIS settings (PR#2216)
...
when DEFAULT_STEPPER_DEACTIVE_TIME is over
instead of simply turn off all.
10 years ago
c85a486445
make the dual z-endstop optional (PR#2277)
...
it's disabled by default
10 years ago
962b107341
Prevent current_command_args from bypassing nul (PR#2270)
10 years ago
06ae832276
Deprecate Support for Arduino IDE < 1.0.5
...
Note that newer versions of the IDE can still
be made to support compilation for the older boards.
10 years ago
ff6081be3a
Parse N[0-9]+[ ]* differently (PR #2263 )
...
More general solution to skip N[0-9]+[ ]* in the parser as in #2218
10 years ago
aad121864e
Include "Z" in M851 report
10 years ago
96a3fba8ac
Reverse the sign of zprobe_zoffset
...
- When editing on the LCD, minus now means below the nozzle
- Stores the opposite sign in EEPROM, so bumped to “V20”
10 years ago
f92907183c
Updated SAV MkI pin header.
10 years ago
58941e543e
ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED removed
...
#defining something just to define something else doesn’t
make sense
If you want SDCARDDETECTINVERTED, just define it yourself.
If the previous code was intended to define, undefined and then again define the term, that code is improper.
10 years ago
788eb6e647
planner.cpp: remove tab
...
planner.cpp: single evil and hidden tab removed ♻️ 😏
10 years ago
3a5963c0e7
Configuration_adv.h: Add FAN_MIN_PWM for slow fan stopping issue …
...
* all Configuration_adv.h: Add #define FAN_MIN_PWM for slow fan stopping
issue
* for K8200: uncommented with tested (and working) values
10 years ago
e55e65d1e4
planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue …
...
@CONSULitAS
planner.cpp: Add FAN_MIN_PWM for slow fan stopping issue (V2.1 with
macro and linear scaling)
@thinkyhead thanks for idea on linear scaling
10 years ago
8d295547be
* Auto filament change on CHANGEFILAMENT feature. Now you can activate this option that extrude filament until you press the button.
10 years ago
6d0e91328d
Renamed Board_megatronics_1 to Board_minitronics
10 years ago
c4a2e5ac23
Renamed Pins_megatronics_1 to Pins_minitronics
10 years ago
2076906aaa
Renamed Pins_megatronics_1 to Pins_minitronics
10 years ago
10733a2bb0
added minirambo pin definitions. V2
10 years ago
303d47228e
Define Probe Path in new format
10 years ago
ad09d6a60f
3 Step Allen Key Probe
10 years ago
8359cdf01d
Check compatibility for Teensy-based processor
...
The instruction say to set a #define in fastio.h
However, that value is not included before this test.
10 years ago
08968c29bb
Adding ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED to Examples
10 years ago
fed18bcc20
Removed SDSLOW for ELB_FULL_GRAPHIC_CONTROLLER
...
Hardware changes has removed the need for this option.
10 years ago
b94a0e1501
Added ELB_FULL_GRAPHIC_CONTROLLER_SDCARDDETECTINVERTED
...
The new define allows the sd card detect to be inverted or not from
Configuration.h
10 years ago
bc205c76a3
SDCARDDETECTINVERTED problems
...
Fixed an error where SDCARDDETECTINVERTED was being defined/undefined
improperly
10 years ago
e400fce271
Merge pull request #2221 from MagoKimbra/Dryrun
...
Insert Debug DRYRUN Repetier Host compatible
10 years ago
163a9ff58e
Merge pull request #2230 from AnHardt/psm
...
Fix thermal protection state machine target temp. V2
10 years ago
c3fe6e61ae
Merge pull request #2229 from AnHardt/position-out-of-range
...
Fix out_of_range_error()
10 years ago
4db8d2def4
Moved MSG_DEBUG in language.h
10 years ago
b7e9ba7591
Back to 1.0.3 dev - for now
10 years ago
d1f4471000
Merge pull request #2146 from Wackerbarth/Versioning
...
Versioning
10 years ago
b1404a0743
fix thermal protection state machine target temp. V2
...
If the target temperature is changed then it would always stay in the reset state.
Thanks to @tonokip.
Replaces #2119
10 years ago
17b0ec84ed
Fix out_of_range_error()
...
For sprintf_P() the first parameter has to be a `char*` not `const char*`.
10 years ago
35af5ef23e
Merge pull request #2225 from Wurstnase/naming
...
consistency name for multiplier
10 years ago
e7e964432b
consistency name for multiplier
...
replace extruder_multiply with extruder_multiplier
like feedrate_multiplier or volumetric_multiplier
10 years ago
d4c6fc5d0a
Merge pull request #2223 from AnHardt/dualz-semicolon
...
Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again.
10 years ago
0d9d21d15f
Add a semicolon to make Z_DUAL_STEPPER_DRIVERS compile again.
10 years ago
76306f9073
Insert Debug DRYRUN Repetier Host compatible
10 years ago
881146bc22
Fix problem Width Cura
10 years ago
11e3f3375d
Merge commit '764e61708b8e73410c7819d59c4970d7089ca6f5' into bugFixing
...
Updated LCD wiki location.
10 years ago
a8670b66a7
Update ru translation
...
Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
10 years ago
93da52d011
Added support for OLED SSD1306 I2C based LCDs.
10 years ago
9c09967803
Merge pull request #2149 from Wurstnase/enstop_bits
...
faster compare
10 years ago
0f3f7d6835
clean up double endstops
10 years ago
9d2a980bcf
Merge pull request #2170 from thinkyhead/beep_M600_elsewise
...
Slight size reduction by adding idle()
10 years ago
2728dc0606
Merge pull request #2194 from thinkyhead/reduce_strings
...
Redo "invalid extruder" to save 304 bytes
10 years ago
be5236e839
Reduce setTargetedHotend by removing the switch
10 years ago
06f401e7e5
Redo "invalid extruder" to save 264 bytes
...
- Use `setTargetedHotend` in `M200`, as with other commands that use
`T` for the extruder
- Synthesize the "invalid extruder" message, obviating several long
strings
10 years ago
1a882bcc2e
Merge pull request #2193 from thinkyhead/ignore_unrecognized_commands
...
Ignore unknown commands if they start with G, M, or T
10 years ago
a672872717
Merge pull request #2187 from AnHardt/MAX6675M105
...
Print active extruder with M105 for MAX6675
10 years ago
9beed830eb
Drop commented code_is_good lines
10 years ago
068d4a1eb2
Ignore unknown commands if they start with G, M, or T
10 years ago
5824f613ff
Merge pull request #2185 from jothan/bed_integral
...
Separate the maximum integral power for the bed from PID_INTEGRAL_DRI…
10 years ago
c5c9d12630
Merge pull request #2183 from AnHardt/displayinit
...
Initialize the display earlier
10 years ago
ef4becc413
Merge pull request #2188 from AnHardt/FtoN
...
Replace MSG_F? with MSG_N?
10 years ago
0564625757
Update M33 for new gcode parser
10 years ago
f18f689c01
Replace MSG_F? with MSG_N?
...
To avoid double definitions.
I prefer to read N for Number not for Nozzle.
10 years ago
af7e3f5076
Print active extruder with M105 for MAX6675
...
Was omitted when T0 is a MAX6675.
10 years ago
d46d9d998e
Add maximum bed integral term in example configurations.
10 years ago
e86f2342c0
Separate the maximum integral power for the bed from PID_INTEGRAL_DRIVE_MAX / PID_MAX.
...
My PID_INTEGRAL_DRIVE_MAX was at 96, which was insufficient for my bed
to reach its intended temperature. The head requires a low maximum power since
I run on 24 volts and it has a somewhat low thermal mass.
10 years ago
f0523b5816
Initialize the display earlier
...
to have it ready to display errors during (temperature)-setup.
10 years ago
790c697c19
Fix DEGREES macro
10 years ago
76b4678f99
Merge pull request #2171 from thinkyhead/gcode_110_is_good
...
M110 is a known command
10 years ago
03d5709b09
M110 is a known command
...
- The command parser now displays “unknown command” in more cases.
Known commands must be added to the `switch` inside `process_commands`
to suppress the error.
10 years ago
d76a01194d
Slight size reduction by adding idle()
10 years ago
2deb5a8ac5
Temporary Hack
...
REVERT THIS CHANGE
In proper use, we want to force the vendor to update this file to reflect distribution parameters
However, until most users have converted to automatic versioning,
we “grant them a pass”
10 years ago
b5743d6927
Use SOURCE_CODE_URL rather than FIRMWARE_URL
10 years ago
5ea139fd79
Revised Versioning mechanism
10 years ago
da246f5cb1
Activate BED_MINTEMP error.
...
And call _temp_error() directly for ERR_MAXTEMP_BED to avoid the only one time use of bed_max_temp_error().
Includes #2156 .
10 years ago
959da98d8e
Call kill() only once when triggered by a temperature error
...
to avoid stack overflow when called from interrupt.
Some clean up for calls of disable_all_heaters().
'disable_all_heaters()' is called in kill() and again when 'killed' is already set inside _temp_error().
10 years ago
68f6f149d0
Reduce code size with out_of_range_error function
...
- Affects code size when automatic bed leveling is enabled
10 years ago
94120740d8
faster compare
...
!(~(ab)&0x3) and ab == 0x3 are equal
10 years ago
c9141e604a
Merge pull request #2145 from thinkyhead/gcode_folding
...
Indentation in process_commands
10 years ago
b55f8718c3
Indent G90/G91, G92
10 years ago
b0d520b109
Indent G30, G31/G32
10 years ago
ffe27a6225
Indent G29
10 years ago
86083badc2
Indent G4, G10/G11, G28
10 years ago
47d7a9cb5e
Indent G2/G3
10 years ago
350f239d84
Indent G0/G1
10 years ago
672b0c1fd3
Cleanup pins in RAMPS_13_EFB boards
10 years ago
15a2351675
No need for +1 on initial seen_pointer
10 years ago
550dd87b2a
Set seen_pointer before calling code_value
10 years ago
38cc0b93c6
Merge pull request #1874 from AnHardt/Bulgarian
...
Introduction of Bulgarian - language_bg.h
10 years ago
04a1622172
Merge pull request #2127 from Wackerbarth/Kossel_Pro
...
Kossel Pro
10 years ago
81c2ca3e10
Merge pull request #2131 from thinkyhead/bq_is_ramps_13_efb
...
Witbox and Hephestos are RAMPS EFB
10 years ago
f919a2fed1
Merge pull request #2134 from AnHardt/preheat-all
...
Shift call of start_watching_heater() into setTargetHotend()
10 years ago
063881b5bd
Fix a couple of doubled semicolons
10 years ago
94dff5b36a
Merge pull request #2137 from thinkyhead/tweak_swh
...
Move millis call in start_watching_heater
10 years ago
70d2f48d4e
Merge pull request #2136 from thinkyhead/M303_suppress_error
...
Suppress the line mismatch error after M303
10 years ago
0c0ace2a04
Remove start_watching_heater() fom M104 and M109
10 years ago
00716d0ca0
Small start_watching_heater adjustment
10 years ago
834747deb7
Merge pull request #2135 from Wurstnase/new_endstop_bits
...
new endstop bits
10 years ago
bde9c70d42
Suppress the line mismatch error after M303
10 years ago
50bd7493cc
Merge pull request #2108 from thinkyhead/m33_long_filename_host_support
...
M33 LONG_FILENAME_HOST_SUPPORT
10 years ago
4d11b29959
Merge pull request #2113 from thinkyhead/command_sanitizer
...
Command sanitizer
10 years ago
ff98b8632b
new endstop bits
10 years ago
9b0fa9c309
Changed dependency of start_watching_heater() in setTargetHotend() to THERMAL_PROTECTION_HOTENDS
10 years ago
bc0764894a
Shift call of start_watching_heater() into setTargetHotend()
...
to warrant watching is set or reset.
Make setTargetBed() in _lcd_preheat() dependant of TEMP_SENSOR_BED.
Use disable_all_heaters() in lcd_cooldown() and abort_on_endstop_hit.
10 years ago
b878bc5620
Introducing the Kossel Pro Build Configuration
10 years ago
1d8f61ca8a
AT90USB is defined in pins.h
10 years ago
735bf2d35f
Describe Custom M Code
10 years ago
f39658c822
M120 and M121 are reversed
10 years ago
6eb4f90ce7
Also synchronize configurator copies of configs
10 years ago
9d1961ebe3
Witbox and Hephestos are just RAMPS_13_EFB
10 years ago
4422365a53
Merge branch 'Development' of https://github.com/MarlinFirmware/Marlin into _temp_error
10 years ago
4113762062
Merge pull request #2130 from AnHardt/kill2
...
Add a string parameter to kill()
10 years ago
89d2ee6f13
Make output on display dependant of ULTRA_LCD
10 years ago
120d4c7a8c
Merge remote-tracking branch 'origin/kill2' into _temp_error
10 years ago
cb6e82dc60
Change from kill() to kill(const char *)
...
in temperature.cpp
10 years ago
9d13942278
Use new kill() with parameter.
10 years ago
6398c5e28d
Merge remote-tracking branch 'origin/kill2' into _temp_error
10 years ago
f4a93ed997
Add a string parameter to kill()
...
Makes the output on the LCD adjustable.
10 years ago
2990c6c45f
Use new kill_() for _temp_error()
...
instead of stop(). We really want to require a reset and no chance to set a new temperature.
10 years ago
9b8c6ed254
Merge pull request #2120 from chris-bo/dogm_config
...
move dogm font selection to configuration_adv.h
10 years ago
06513565e9
Merge pull request #2105 from eboston/Development
...
Add ELB_FULL_GRAPHIC_CONTROLLER with ADAFRUIT_ST7565 display.
10 years ago
082ed3beed
Propagate Configuration.h changes
...
Updated all the example Configuration.h files for the new display type.
10 years ago
152b681bb5
Added link to controller github
...
Added the link to the github information about the
ELB_FULL_GRAPHIC_CONTROLLER
10 years ago
995b84944b
Merge pull request #1982 from CONSULitAS/Development_Update_language.h
...
language.h: update documentation / URL für K8200
10 years ago
7bc5fd8193
Merge pull request #2123 from AnHardt/Duemilanove
...
Remove Duemilanove
10 years ago
94de1e0d93
Merge pull request #2116 from AnHardt/wording
...
transpire -> expire
10 years ago
4d4fa3607b
Remove Duemilanove
...
No way to fit Marlin into 32K.
10 years ago
e353d27430
Merge branch 'Development' of https://github.com/MarlinFirmware/Marlin into Bulgarian
10 years ago
ca8d1756d5
Define fixes
...
Fixed a couple defines that were not changed or commented out.
10 years ago
b96b28b7cc
language.h: update documentation for LANGUAGE_INCLUDE
...
language.h: update documentation for LANGUAGE_INCLUDE
@thinkyhead What do you think? I think there should be a warning like
this.
10 years ago
258bcdefe0
move dogm font selection to configuration_adv.h
10 years ago
7750180c93
transpire -> expire
...
Minor wording correction.
10 years ago
70163dafb9
Use _temp_error() for all errors thrown by different mechanisms
...
Now ending in an endless loop.
Tidy up the output format.
We now get:
ERRORTEXT ", system stopped! Heater_ID: " HEATERID
Where ERRORTEXT can be:
"Heating failed"
"Thermal Runaway"
"MAXTEMP triggered"
"MINTEMP triggered"
and soon
"Thermal Jump"
HEATERID can be
0, 1, 2 ,3 , "bed"
This messages are always followed by the common:
"Printer stopped due to errors. Fix the error and use M999 to restart. (Temperature is reset. Set it after restarting)"
10 years ago
a0f362c735
Simplify & optimize with current_command_args
10 years ago
adc8fcb77f
More parser comments, optimize code_seen, save with goto
10 years ago
c6d8dd19d9
use fetched value
10 years ago
1116e13f5a
Further optimization of command parser
10 years ago
3a4c3ab76e
Pre-sanitize the command before handling
...
- Use a global pointer for the current sanitized command
- Pre-sanitize the current command to bypass `N` and nullify `*`,
removing the need for handlers to bypass, ignore, or nullify these
parts, and reducing overhead for `code_seen`, etc.
- Pre-skip leading whitespace.
- Only look for G, M, T codes at the start of the command.
- Verify that G, M, T codes are followed by command codes.
10 years ago
a83bf18ee1
More functional seperation
...
Moved SDCARDDETECTINVERTED and SDSLOW to Conditionals.h.
Added U8GLIB_LM6059_AF to define display specific actions.
Added reminder to compile in u8glib
10 years ago
97ca1b3f4d
Name magic value 20 to MAX_OVERSHOOT_PID_AUTOTUNE
...
to make it better findable.
10 years ago
0f2c9bacfd
M33 LONG_FILENAME_HOST_SUPPORT
10 years ago
3feaef6526
Have G92 set the nozzle position on Delta and SCARA
10 years ago
047e688e93
Changed ADAFRUIT_ST7565 to ELB_FULL_GRAPHIC_CONTROLLER
...
Rename of define to avoid confusion between the controller and the
display which had similar names.
10 years ago
1999ac415c
Formatting Changes
...
Fixes for some code formatting changes and commenting out the
ADAFRUIT_ST7565 define that was left defined.
10 years ago
41f8cdb3a6
ADAFRUIT_ST7565
...
Added support for new display type
10 years ago
21ff773832
rework out_bits
10 years ago
6c27eaf864
Merge pull request #2101 from thinkyhead/code_style
...
Code style and a dangling "else"
10 years ago
d580a0d186
Use "+=" in plane rotation
10 years ago
2f3a410cb0
Fix a potential hanging "else" bug
10 years ago
b83e3f0905
Combine "Bed X: " strings
10 years ago
7dfb8becdb
Adjust some names and types in Marlin_main.cpp
10 years ago
c966aa26ff
Comments in Marlin_main.cpp
10 years ago
c54a2ea042
Adjust spacing in Marlin_main.cpp and stepper.*
10 years ago
072625ccad
Update headings in Marlin_main.cpp and stepper.cpp
10 years ago
16032f149f
Rename to codenum as a consistency
10 years ago
273a4a253f
Merge pull request #2096 from thinkyhead/cherry_picking3
...
Hide M117 with no LCD
10 years ago
64825a3d1e
Merge pull request #2095 from thinkyhead/cherry_picking2
...
Add gcode_line_error to reduce code size
10 years ago
ca79282eaf
Hide M117 with no LCD
10 years ago
ce218cafdb
Add gcode_line_error to reduce code size
10 years ago
46d59784ad
Rename preocess_command to process_next_command
10 years ago
513077c317
Minor change to fan kick
10 years ago
76438195f0
NO_TIMEOUTS and ADVANCED_OK off by default
10 years ago
d2563804c8
Add LF to file errors
10 years ago
e114662cfa
Adjust SdBaseFile spacing
10 years ago
98e91f5253
Allow lsDive to recurse with minimal stack usage
10 years ago
19166a92e4
Merge pull request #2057 from Wurstnase/serial_wait
...
add plan buffer remaining for 'P' and block buffer remaining 'B'
10 years ago
95f5a68006
Merge pull request #2074 from thinkyhead/lcd_xyz_unknown
...
Display unknown XYZ on the LCD as "---"
10 years ago
e97fcafd0e
Merge pull request #2076 from thinkyhead/mendel_inverting
...
Use MSG_OK in M105
10 years ago
0f6cd3640b
Drop extraneous ok_to_send
10 years ago
0ce355d9e7
Use MSG_OK in M105
10 years ago
a366e57385
Merge pull request #2075 from thinkyhead/mendel_inverting
...
Use Mendel default for INVERT_Y_DIR
10 years ago
7b3acfbb6f
Merge pull request #2072 from thinkyhead/better_arc_code
...
Consolidate arc code, remove motion_control.*
10 years ago
78beef2d73
Use Mendel default for INVERT_Y_DIR
10 years ago
1a4a09c26f
Display unknown XYZ on the LCD as "---"
...
- Also show 2 digits past decimal for Z on DOGM
10 years ago
68ce419147
Note on segment size
10 years ago
8b92249f18
Bring arc_offset into auto scope
10 years ago
80807b2d71
Consolidate arc code, remove motion_control.*
10 years ago
f65833931d
Formatting tweaks
10 years ago
fcfd99c1ae
Add comments to lcd_control_temperature_menu
10 years ago
d693e0f378
Use WATCH_TEMP_INCREASE + TEMP_HYSTERESIS + 1 as difference limit
10 years ago
6697a8f375
Watch the heater a little longer
10 years ago
5693a6e3c9
Fix heating error message
10 years ago
747fd5801c
Merge pull request #2055 from thinkyhead/thermal_unified
...
Combine thermal runaway and watch-period
10 years ago
6e5572228d
Merge pull request #2064 from thinkyhead/wait_before_g28
...
Split up prepare_move by type
10 years ago
27ad381e25
Allow fractional seconds in G4 and M0
10 years ago
5146694452
Merge pull request #1884 from shaggythesheep/feature_new_board_ramps_cnc_controller
...
Feature: Add RAMPS CNC Controller Board
10 years ago
b2bd9aae7c
SCARA_SEGMENTS_PER_SECOND
10 years ago
bd20bd5444
Merge pull request #2063 from chris-bo/autobed_sled
...
improve sled handling
10 years ago
9e95ceb3fc
Split up prepare_move by type
...
- For better encapsulation add inlines for each prepare_move type
- Move controllerFan vars inside the function as statics
- Some formatting cleanup
- Rename `ClearToSend` as `ok_to_send`
10 years ago
9ba8cf5fe3
Merge pull request #2061 from thinkyhead/wait_before_g28
...
Always do st_synchronize() before G28
10 years ago
873f7d6f2a
Check that configs are up-to-date
10 years ago
f48599f172
add pin definition to some motherboards
10 years ago
b5200e184c
Remove extra setup_for_endstop_move
10 years ago
8d814de558
Return void in prevent_dangerous_extrude
10 years ago
367e2eb9f4
Global setup_for_endstop_move
10 years ago
1d5677cc3b
add missing Z-bits
10 years ago
df12e68e7d
add missing Z_PROBE-bit
10 years ago
fa951f8a0b
Always do st_synchronize() before G28
10 years ago
27a3b1d895
disable sled pin by default
10 years ago
fb44b53ae3
sled improvements
...
- create sled pin definition
- G28 Works with sled
10 years ago
46d1932380
add plan buffer remaining for 'P' and block buffer remaining 'B'
10 years ago
429c6ccad2
Neaten config formatting
10 years ago
8a0dc4d54a
Merge pull request #1922 from Wurstnase/serial_wait
...
Serial wait
10 years ago
8332a15899
Fix testing of runaway options in temperature.cpp
10 years ago
526ad82d20
activate advanced_ok and no_timeout
10 years ago
2b92b01afc
Fix typo in SanityCheck.h
10 years ago
2445ae3d3a
Combine thermal runaway and watch-period
...
- Make thermal protection for all hotends and/or bed into simple
switches
- Now enable `WATCH_TEMP_PERIOD` when `THERMAL_PROTECTION_HOTENDS` is
enabled
- Move detailed thermal parameters to `Configuration_adv.h`
- Add sanity checks to warn about old configurations
- Change `WATCH_TEMP_PERIOD` to seconds instead of milliseconds
10 years ago
4097207c75
Merge pull request #2041 from thinkyhead/watch_temp
...
More thermal protection
10 years ago
45d64040fe
Merge pull request #2048 from Wurstnase/hit_bits
...
replace some bools
10 years ago
9b3d4380d3
Only watch the heater that was set
10 years ago
52c0696e44
Merge pull request #2044 from thinkyhead/fix_servos_too
...
Make some z probe and servo code tweaks
10 years ago
b55f32f8a1
replace some bools
...
this PR replaces some bools with one char. this will safe 3 bytes and should also be sometimes a little bit faster.
10 years ago
e70e6e2b48
Correction traductions
10 years ago
f73f4ce555
Make some z probe and servo code tweaks
10 years ago
28c87ec81b
Disable all heaters on temp error
10 years ago
79106638a8
Fix documentation of heating sanity check
10 years ago
6110494a56
Change default to 4°C in 16s
10 years ago
54deb9eea3
Enable WATCH_TEMP_PERIOD by default
10 years ago
deedb00c18
Document WATCH_TEMP_PERIOD
10 years ago
be77cfd895
Merge pull request #2032 from Wurstnase/toshiba_for_all_stepper
...
We don't need the old standard one. The STEP_ADD and STEP_IF_COUNTER …
10 years ago
cb4ea75fab
Support for MKS BASE 1.0 board
10 years ago
0e70511381
Merge pull request #2036 from brupje/mainline
...
Fixes for reprapworld's keypad
10 years ago
0cb87795a3
advanced 'ok'
...
ok N(linenumber) P(bufferremaining)
the host can use this to send the data much faster.
Some pseudo code:
If (bufferremaining > 0) send command
## as long there is free buffer send command
Also
if (linenumber > lastsend - bufferremaining) send command
## as long last linenumber received is bigger than lastsend (host) - last bufferremaining received
10 years ago
182e0d99c9
Merge remote-tracking branch 'Marlin8bit/Development' into serial_wait
10 years ago
d1148a0198
Rename Configuration_megatronics.h to Configuration.h
10 years ago
7f3252eea9
Merge pull request #1999 from paclema/Filrunout_configurable_script
...
Added configurable script for filrunout from configuration.h
10 years ago
181ccc884c
Edit thermal runaway description
10 years ago
073e4af7e2
We don't need the old standard one. The STEP_ADD and STEP_IF_COUNTER are also good for non-Toshiba stepper driver.
10 years ago
b7fcb11580
Added example configuration for Megatronics
10 years ago
8f8174dc93
Revert "Default configuration for megatronics."
...
This reverts commit 22e0d2afcb
10 years ago
79633a74ab
Fix MBL compile error
10 years ago
ba9741139e
Clean up pins file for megatronics
10 years ago
22e0d2afcb
Default configuration for megatronics.
10 years ago
Richard Wackerbarth