2f4a20257c
imported last Marlin changes
10 years ago
50b4e86f75
Add "Thermal Runaway Protection" feature
...
This is a feature to protect your printer from burn up in flames if it
has a thermistor coming off place (this happened to a friend of mine
recently and motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature
than actual. The system will turn the heater on forever, burning up the
filament and anything
else around.
After the temperature reaches the target for the first time, this
feature will start measuring for how long the current temperature stays
below the target minus _HYSTERESIS (set_temperature -
THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
If it stays longer than _PERIOD, it means the thermistor temperature
cannot catch up with the target, so something *may be* wrong. Then, to
be on the safe side, the system will he halt.
Bear in mind the count down will just start AFTER the first time the
thermistor temperature is over the target, so you will have no problem
if your extruder heater takes 2 minutes to hit the target on heating.
10 years ago
b5417be109
Update Configuration.h
...
Leapfrog added to the board list
11 years ago
43c298a7a9
Add "Thermal Runaway Protection" feature
...
This is a feature to protect your printer from burn up in flames if it
has a thermistor coming off place (this happened to a friend of mine
recently and motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature
than actual. The system will turn the heater on forever, burning up the
filament and anything
else around.
After the temperature reaches the target for the first time, this
feature will start measuring for how long the current temperature stays
below the target minus _HYSTERESIS (set_temperature -
THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
If it stays longer than _PERIOD, it means the thermistor temperature
cannot catch up with the target, so something *may be* wrong. Then, to
be on the safe side, the system will he halt.
Bear in mind the count down will just start AFTER the first time the
thermistor temperature is over the target, so you will have no problem
if your extruder heater takes 2 minutes to hit the target on heating.
11 years ago
512f2a3136
restore Branch from Backup
...
sorry for that
11 years ago
6e6e4e2143
Added thermistor table for the 500C thermistor shipped with the Pico hot end.
11 years ago
8a32c5395b
renaming the disable inactive extruder feature
11 years ago
29e7639933
Add switch unused feeder(s) off
...
Having the non-active feeder motors powered on all the time is not
necessary. A feature to deactivate the unused feeder motors has been
implemented. The feature is enabled on default but can be switched off
in the configuration.
11 years ago
09b84faa00
Configuration.h, pins.h: Add MOTHERBOARD 84 for Teensy++2.0
11 years ago
1c9a70cee9
Support for Gen3 Monolithic electronics
...
Techzone Monotronics support, ignoring the tip manager and using fan connector as on Sprinter FW
TODO: Add support for tipmanager
11 years ago
2acd3792fc
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
11 years ago
8b4c4aa5c3
Add feature to check&retry CRC read errors on SD.
11 years ago
da6b536182
Add 5DPrint D8 Driver Board info and temperature table for Makibox hot bed
11 years ago
3161740df9
This table is made for thermistor 3950 (can be found on ebay for cheap)
...
it's caracteristics are :
R25℃ ;100KΩ±1%
B Value(R25/50℃)：3990K 1%
Dissipation Factor(mW/℃)：1.1~1.6 In still Air
Thermal Time Constant(S)：10~17 In Still Air
Operating temperature range： (-50~+260°C)
Dimension： 1.8mm Dia X4.1mm
Lead Length ：30mm
This table was found on the following blogs:
http://cae2100.wordpress.com/2014/03/08/beta3950-thermistor-table-for-marlin/
and
http://microfabricator.com/articles/view/id/531ad7e59aad9d3131000000/beta-3950-thermistor-table-for-marlin
11 years ago
d3f305332a
Allowable range now includes default value
11 years ago
b0aeac117f
Adjustable Z probe offset, via custom M-code
11 years ago
b0093a1513
thermistortables.h: Add comments that table 60 uses beta=3950.
11 years ago
174b8d99d5
Simplify 3-point probing using new code only
11 years ago
3b718b816c
better documentation
11 years ago
34fd59c370
ABL at any points
11 years ago
3f455889d0
Merge pull request #769 from Cylindric3D/typofixes_1
...
Various typo fixes - only in comments, no code changes.
11 years ago
d4ba23bc28
Merge pull request #770 from josefpavlik/Marlin_v1
...
Marlin v1
11 years ago
ab0d3c4fb3
Various typo fixes - only in comments, no code changes.
11 years ago
831fc2a952
Pt100 and Pt1000 temperature sensors handling
11 years ago
71bb3a8133
Add comments for Ultimainboard 2.0 configuration.
11 years ago
b819fc53ca
Add Azteeg X3 Pro as motherboard 68
...
Add digipot i2c control for MCP4451
Allow M907 to set i2c digipot currents in amps
Fix Makefile to allow Azteeg motherboards
Fix Makefile to allow Wire libraries only
Add beeper pin for Azteeg X3 Pro
11 years ago
e1ae7952eb
Merge pull request #743 from Opticalworm/Marlin_v1
...
Improved support for panelolu2 encoder and buzzer
11 years ago
a5f53f0cf3
Heater wattage reporting for M105 using EXTRUDER_WATTS and BED_WATTS
11 years ago
8d162e5bd7
Improved support for panelolu2 encoder and buzzer
...
I added #define for LCD_FEEDBACK_FREQUENCY_HZ and
LCD_FEEDBACK_FREQUENCY_DURATION_MS which is used to alter the default
buzzer sound.
When selecting Panelolu2 in configuration.h:
- it automatically sets the correct ENCODER_PULSES_PER_STEP and
ENCODER_STEPS_PER_MENU_ITEM.
- if LCD_USE_I2C_BUZZER is defined it will also set the default
LCD_FEEDBACK_FREQUENCY_HZ and LCD_FEEDBACK_FREQUENCY_DURATION_MS
When selecting the sanguinololu 1284p the following is true:
- its now enables LARGE_FLASH
- It enables the gcode M300 when the panelolu2 LCD_USE_I2C_BUZZER is
defined
11 years ago
76cf07c3f7
Configuration.h: Use OVERSAMPLENR in dT_PID definition.
11 years ago
6ae7f7870d
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into ErikZalm
...
Conflicts:
Marlin/Configuration.h
Marlin/Marlin_main.cpp
11 years ago
e5d3044801
Added posibility to set ENCODER_STEPS_PER_MENU_ITEM in Configuration.h like ENCODER_PULSES_PER_STEP as it depends on it for usability
11 years ago
e8786bf110
Added support for Cheaptronic v1 electronic
11 years ago
cc2925b705
Implemented a least squares fit of the bed equation for auto bed leveling.
...
The code for the LSQ solver (qr_solve) is copyrighted by John Burkardt and released under LGPL here:
http://people.sc.fsu.edu/~%20jburkardt/c_src/qr_solve/qr_solve.html
(see qr_solve.cpp for further copyright information)
11 years ago
b33375d438
Z Axis Safe Homing when using Z Probe
...
Recommended for those who are using the Z Probe for Z Homing (as
Z-Endstop)
This feature has two changes:
1) Allow user to choose where the Z Probe will touch the bed when homing
all axis together (G28) by setting below defines:
Z_SAFE_HOMING_X_POINT
Z_SAFE_HOMING_Y_POINT
2) Prevents the user to perform Z Axis Homing when the Z Probe is
outsite bed.
11 years ago
48a185d004
Fixed compile errors from bad commits.
11 years ago
59b96e323e
Merge pull request #640 from fmalpartida/SAV-MkI
...
Added support for BT on AT90USB devices, corrected LCD bug, added new board and LCD
11 years ago
7b556d2e96
Added BT support on AT90USB devices
...
Added AT90USB device BT connectivity support using second UART.
11 years ago
a5e8575829
Add UUID support to M115 responses.
11 years ago
b5a964fcc5
Initial SAV MkI (RepRap CloneWars board) integration.
...
Included support for BT dongle on AT90USB boards.
Added LCD Shift Register LCD control
Included support for RepRap Clone Wars project board (SAV MKI).
11 years ago
f941203172
PS_ON configurable boot state
...
Allows the user to select wheter or not the PSU should be turned on or
kept in standby when marlin boots
11 years ago
8a08cca0f2
Added temperature status less.
...
Hopefully fixed viky button handling without braking other boards
11 years ago
6a803ba9c5
Merge pull request #590 from timkoster/Marlin_v1
...
Added BlinkM support over i2c
11 years ago
6f85a8c7aa
Bed auto Leveling change: Raise Z before homing
...
- Added "Z_RAISE_BEFORE_HOMING" for raising Z the defined distance
before homing. This is useful to avoid Z-Probe collision when hotend is
near bed.
- Fixed the issue of Z not going bellow Z_PROBE_OFFSET when
"min_software_endstops" is true.
Now the Z_PROBE_OFFSET is not set in Z_MIN_POS, it is added after
homing.
11 years ago
253dfc4bc1
Bed Auto Leveling feature
...
Check the Readme for instruction how to enable and configure the feature
11 years ago
57173739a1
Update Configuration.h
...
Include CPU Sethi 3D
11 years ago
0dca49a7c0
Added Azteeg X3 board.
11 years ago
d8c2c810b4
Added info to the delta configuration files in the configuration.h file
11 years ago
9bc88f8bab
Placed optional ENCODER_PULSES_PER_STEP in the configuration.h file
11 years ago
61db046b32
Added #ifdef BLINKM around new code. Also refined BlinkM.h.
11 years ago
3626b5ad8b
Removed Delta from the default config file.
...
Changed EEPROM CHITCHAT behavior. M503 is always enabled.
11 years ago
88dfeefca3
Define BlinkM default disabled
11 years ago
5350faf2a2
Merge https://github.com/timkoster/MarlinBlinkM into Marlin_v1
11 years ago
7016cc9511
Added BlinkM support over i2c
11 years ago
3b315b3da0
Added BlinkM support over i2c
11 years ago
a54fe2d73c
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1
...
Conflicts:
Marlin/Marlin_main.cpp
11 years ago
2ca983568d
separate INVERTING for MIN and MAX endstops (6 #defines instead of 3)
11 years ago
9bf1cf1b22
Pre-calculate diagonal rod length squared
11 years ago
4623e78ce0
Added Honeywell thermistor 135-104LAF-J01
11 years ago
34da3a0a3f
Merge github.com:ErikZalm/Marlin into Marlin_v1
...
Conflicts:
Marlin/language.h
11 years ago
c4a2077951
M109 and M190 now wait when cooling down if R is used instead of S.
...
M109 S180 waits only when heating.
M109 R180 also waits when cooling.
12 years ago
6397b3339c
restored configuration.h defaults
12 years ago
e509cdbeb0
added contrast control function for gLCDs
12 years ago
99b7e926e7
added MaKr3d Melzi board
12 years ago
ecf3ab5de4
Added thermistor 60 to configuration.h
12 years ago
2daa85918e
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
Marlin/Marlin_main.cpp
Marlin/language.h
Marlin/pins.h
Marlin/ultralcd.cpp
12 years ago
2015989f84
Added DISABLE_MIN_ENDSTOPS
12 years ago
648d45cfb2
Fix Pin Description Typo
...
Reverse 'Bed' and 'Fan' at the RAMPS 33 Description.
Signed-off-by: Christian Inci <chris.pcguy.inci@gmail.com>
12 years ago
02dee80fa5
added Azteeg X1 motherboard
12 years ago
e34c9981ab
Delta disabled by default
12 years ago
7ad12be763
Merge branch 'Marlin_v1' of https://github.com/codexmas/Marlin into codexmas-Marlin_v1
...
Conflicts:
Marlin/Configuration.h
README.md
12 years ago
408169aef4
Merge branch 'Marlin_v1' of https://github.com/BorisLandoni/Marlin into BorisLandoni-Marlin_v1
...
Conflicts:
Marlin/Configuration.h
Marlin/language.h
Marlin/pins.h
12 years ago
bd96d22bfb
Merge branch 'Marlin_v1' into thinkyhead
...
Conflicts:
Marlin/Configuration.h
Marlin/Configuration_adv.h
Marlin/Marlin.h
Marlin/Marlin_main.cpp
Marlin/Servo.cpp
Marlin/language.h
Marlin/pins.h
Marlin/planner.cpp
Marlin/ultralcd_implementation_hitachi_HD44780.h
README.md
12 years ago
6f4a6e531c
Merge branch 'deltabot' into Marlin_v1
12 years ago
ff6fa09ecf
Moved corexy implementation from stepper to planner
...
(Thanks iquizzle)
12 years ago
c8dcc7c208
Allow increasing the software PWM frequency.
12 years ago
373f3ecab3
Merge branch 'deltabot' of https://github.com/jcrocholl/Marlin into deltabot
...
Conflicts:
Marlin/Configuration.h
Marlin/Marlin_main.cpp
Marlin/pins.h
12 years ago
6a81291c57
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
...
This should fix issues with pull request 467, I hope.
Conflicts:
Marlin/Configuration.h
Marlin/Marlin.pde
Marlin/ultralcd_implementation_hitachi_HD44780.h
12 years ago
c1cb5977ee
Update Configuration.h
12 years ago
8a5bd8a808
Update Configuration.h
12 years ago
6588933c04
Update Configuration.h
12 years ago
5dabc95409
Apply all changes from latest Marlin_V1
...
Diffed and merged, preserving my updates
12 years ago
f4f30c9d64
Added servo actuated enstop coding to allow G28 command to engage and retract a servo to specified angles.
12 years ago
79374f0b93
Merge branch 'reisnyderb' of https://github.com/ErikZalm/Marlin into Marlin_v1
12 years ago
4b19c8552e
Fixing changed Configuration.h settings to be default values per ErikZalm Request.
12 years ago
5090c56651
More redundant temp sensor changes. (After testing and debugging by reifsnderb)
12 years ago
b78fa6bb70
Added support for Megatronics v2.0 and Minitronics v1.0
...
merged from code downloaded from reprapworld.com
12 years ago
9be61cdc02
Added redundant temp sensor
12 years ago
e2ff536b03
Fixed typo in Comment
12 years ago
0d4a9444c4
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
12 years ago
28ada096e2
Adding servo documentation
12 years ago
dfa549f268
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
12 years ago
dc59f07d24
First attempt at refactoring of original servo code. Only adding servo support as a start to keep things simple.
12 years ago
bd2cd4903e
Added #ifdef BARICUDA around the BariCUDA changes
12 years ago
2739c26c4f
changes:
...
- changed the variables from keypad to reprapworld_keypad
- added a missing ifdef check
12 years ago
6fb9573157
added support for the reprapworld keypad
12 years ago
1fa61c297e
Turning off Control Panel by Default and Updating the link to the LiquidCrystal_I2C library to avoid confusion.
12 years ago
b27a59f41e
Added support for Elefu RA Board and Elefu Control Panel
12 years ago
0ef54f2f85
Make M303 silent when "S0" is sent
...
If S is left out perhaps it should be silent, but check the spec for
this M code.
12 years ago
a200521eab
Added CUSTOM_MENDEL_NAME option to Configuration.h and language.h
...
Also cosmetic comment changes and spelling corrections in printed
messages
12 years ago
1a397825f9
fix DEFAULT_AXIS_STEPS_PER_UNIT minor Z rounding error
12 years ago
c3cdaceab3
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
12 years ago
788d62bcc4
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Marlin.pde
Marlin/ultralcd.cpp
Marlin/ultralcd_implementation_hitachi_HD44780.h
12 years ago
d71f1e9bf6
Add (as an option) slower SD transfer mode
12 years ago
13596e8722
Added RepRapDiscount FULL GRAPHIC Smart Controller
12 years ago
c80a78bb70
Lower the default max E feedrate a bit. With the stepper fix this is much to high.
12 years ago
7a5c474d91
Update Configuration.h
12 years ago
9fb8bd5685
Merge pull request #433 from whosawhatsis/bang-mode
...
Separate PID_MAX from BANG_MAX
12 years ago
9322c408c6
Updated for LiquidTWI2 library version 1.2.3
...
The new version of the library means that PANELOLU no longer needs to be
defined in LiquidTWI.h (the library file can be used as is) and the new
version of the library also enables the buzzer on the Panucatt VIKI
panel.
12 years ago
fd5b7e0cec
Separate PID_MAX from BANG_MAX
...
This allows PID_FUNCTIONAL_RANGE to use a maximum duty cycle higher
than PID_MAX. This is useful for powerful heaters to heat quickly in
bang-bang mode, but use a lower duty cycle that is easier to stabilize
in PID mode.
12 years ago
72419f69a9
Added rumba
12 years ago
aba67e2449
No bed config for RAMPS
...
The motherboard 35 is a config without bed with this pins setting :
D8 Extruder
D9 Fan
D10 Controller Fan
12 years ago
7bad72359c
Support encoder click on PANELOLU2 being read through I2C
...
This change also handles the case where the pause/stop/restart button on
the VIKI is not used. Make LCD I2C buzz sound the same as the normal
buzz (300ms is too long for quick feedback).
12 years ago
1daf2f3256
Number of extruders is not an advanced configuration - it is a basic property.
12 years ago
b2c1c64fb1
Add Motherboard variant 64 - STB V1.1
...
Definition for the graphic LCD are already in it, they will not harm the
configuration as they are only defined constants
12 years ago
6beb42cdf6
Attempt to address Bernhard's comments
...
Refactor configuration to try to make items clearer (what defines a
panel vs what is user changeable).
12 years ago
839bef6d5d
Fix Configuration.h file to not define LCDs be default.
...
Also fix compile time check in Marlin.pde
12 years ago
1292d735ba
Converge all I2C LCD branches (PANELOLU2, VIKI & PCF8575)
...
This includes refactoring the buttons code to remove a large amount of
non-pin dependent duplication from pins.h.
12 years ago
67710df9f3
Made i2c mode wok with the hardware I am able to test (ywrobot / sainsmart i2c LCD 2004)
...
Removed incorrect LiquidCrystal_I2C Library
12 years ago
2b567d1df5
Added I2C port expander support to HD44780
12 years ago
06272f463d
Added Config variables for activating I2C LCDs and setting type and address
12 years ago
70871715e4
Added support for extruder offset handling
...
The extruder offset can be specified in the configuration
file or adjusted on the fly using the "M218 T# X# Y#" command.
The EEPROM support is not yet merged in.
The "T#" command can take option "F#" that specifies the feedrate
at which the printing head should be re-positioned. If not
specified the re-positioning move is not preformed immediately,
but the coordinates are adjusted for the printer to properly
position the head when the next movement happens.
12 years ago
9ecb267b63
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
12 years ago
3cf59f6f9a
add RepRapPro Huxley thermistor tables
12 years ago
bbe7d3d0fe
Fixed #312
12 years ago
8b88e3b386
Fixed #345 , Fixed #267 .
12 years ago
f3c1fc70a9
Power signal control definitions for ATX and others
12 years ago
6752cb2d9c
PID now per extruder. Fixed typo
12 years ago
0ac452e252
Disable is now multi extruder compatible. M84 got a T option.
12 years ago
9e7b5056a0
{X,Y,Z}_{MIN,MAX}_POS are actually in Gcode coordinates.
12 years ago
1c2ecddae4
Fix typo (# missing before define).
12 years ago
3b2e5027e5
Merged updates from Marlin_v1.
12 years ago
55ba90ac19
Add PID functional range setting. With high powered heaters the current functional range of 10 degrees causes high overshoots as the PID needs to kick in before the temperature hits 10 degrees below target.
12 years ago
5ff5cee8ce
Fix the sensitive pin definitions, there where analogue numbers in the digital pin list. Also made M42 without a P function on the LED_PIN (which was otherwise a useless pin definition)
12 years ago
1f45cb0a51
Fix typo in MANUAL_HOME_POSITION (plural S missing) and improve comments.
12 years ago
c430906d3b
Deltabot settings and configuration adjustments.
12 years ago
42e21bb06e
Add support for Printrboard (from https://github.com/lincomatic/Marlin ) and Brainwave (from https://github.com/metrix/Sprinter ).
12 years ago
f934d0ef5b
Merge remote-tracking branch 'tonokip/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
12 years ago
2f771b3979
Added automatic build numbering.
12 years ago
a27fef8750
Store the pre-heat constants outside of the ULTIPANEL define, so we can use them when storing EEPROM in a build without the ULTIPANEL.
12 years ago
ffc69537aa
Update on some comments, make the MOTHERBOARD list complete again.
12 years ago
46b9988e26
Search and replace failure.
12 years ago
36b452c7ac
Remove abbrs.
12 years ago
3cbaad9288
RepRapDiscount Smart Controller pin definitions.
12 years ago
65c9a0728f
Set default serial port back to 0.
12 years ago
ab9d183024
Make serial port configurable.
...
This change makes the choice of serial port configurable so that
wireless capability can be easily added by connecting Bluetooth modules
(such as BlueSmirf or JY-MCU) to the expansion port pins.
12 years ago
326423719f
Add support for Megatronics
12 years ago
36a746d7d5
Merge pull request #244 from markfinn/pidbed
...
PID for heated bed
12 years ago
04631d2250
cleanup for pull
12 years ago
c6caa45ae2
Limit Switch locations based on MIN/MAX limits and homing direction
...
fixes #246
Added statements to set the limit switch positions to the maximum travel if homing in the positive direction as well as bed center at (0,0) if defined.
Relocated code based on feedback.
12 years ago
dc566d654f
fixes #246
...
Added statements to set the limit switch positions to the maximum travel if homing in the positive direction as well as bed center at (0,0) if defined.
12 years ago
9698f4ea64
bed pid
...
Conflicts:
Marlin/Configuration.h
12 years ago
e358a2d7af
Added fix for SF Arc Point fillet procedure
12 years ago
1c1fddc7ac
Added support for the Rambo reprap electronics board. Added Mcodes to set
...
motor current and microstepping pins.
12 years ago
5406c533db
Disable FAST_PWM by default. On some systems it does not work ok.
12 years ago
6b45e9f167
Add Duty Cycling to the Heater Bed
12 years ago
538189cc19
Fixed soft limits when the origin is in the middle.
...
HOME_POS is now always where the endstop is and can be outside the limits.
The limits are now defined by MIN_POS and MAX_POS rather than HOME_POS and MAX_LENGTH.
The Z is axis now homed first if direction is away from the bed.
Saguinololu limit pins change from MIN to MAX according to the homing direction.
13 years ago
ea2c19f978
Added CoreXY support (Thanks Ilan Moyer)
13 years ago
aa65fe22ed
decoupled axes sucessfully at least on pure x or y jog
13 years ago
0c123950e9
__ header file replace
13 years ago
0e5e249ab5
added individual pullup setting option to have finer control in case there is a special z-min sensor, for example
13 years ago
6b14f95b3e
Merge pull request #170 from linagee/Marlin_v1
...
Marlin v1
13 years ago
fbd282b3ba
Update Marlin/Configuration.h
13 years ago
c4490f5f3d
Update Marlin/Configuration.h
13 years ago
7244aa7eb7
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
13 years ago
de2ca3b2e8
Grammar correction.
13 years ago
c2fc466e1b
Update Marlin/Configuration.h
13 years ago
9f9f498491
Update Marlin/Configuration.h
13 years ago
602c8ee02b
Melzi support
13 years ago
e3fe1f0d00
Made a more granular configuration possible PREVENT_LENGTHY_EXTRUDE. You can now decide to allow/disallow large length of extrusions to be executed.
...
Turning off the protection might be beneficial to those who want to do fast and long reversals.
13 years ago
1874cb71a6
Added option to increase the FAN PWM frequency.
13 years ago
e3821bd86f
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
13 years ago
02af69911e
Added temperature window to M109. This is needed for systems with no overshoot PID.
13 years ago
464b755918
added support for the UltiController
13 years ago
67cf105bc6
Fixed AUTOTEMP (M109 S215 B260 F1 starts autotemp)
...
Changed SLOWDOWN. IF this does not work ok OLD_SLOWDOWN is the old algo.
13 years ago
63aec3c56e
Replaced Kill by Stop. If the printer is stopped. Fix the error and use M999 to restart.
...
Moved the PID_dT in the Ki and Kd calculation from the configuration.h to temperature.cpp
13 years ago
aa6e6e914e
Makefile: Redone
...
+ Removed most explicit pathnames, use the standard make "VPATH" to let
make find the files for itself.
+ Added a "hardware variant" variable that allows compiging Sanguino and
Gen7 as well as "generic" arduino.
+ Allows overriding the MOTHERBOARD define from the Makefile
+ Removed the 'preprocessor' bit that wasn't needed, now just "include" the
files that are needed, since it allows gcc to show the right file/line
when displaying error/warnings.
+ Uses gcc's own dependency generator to generate the .d files, and
and include these instead of self-patching the makefile
Signed-off-by: Michel Pollet <buserror@gmail.com>
13 years ago
2e749d60c3
Added DISABLE_MAX_ENDSTOPS
13 years ago
910f4e77a2
Added 20MHz support.
13 years ago
e056bf8081
Added E-Jerk
13 years ago
b65ef8d66c
Add support for upcoming Gen7 v1.4
...
V1.4 moves thermistor power to the always-on 5v line.
The BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE is no longer
needed on this board. Add a new motherboard type to
support this feature.
13 years ago
97d42ca2b2
SDSUPPORT default disabled
13 years ago
018c567abf
Moved SLOWDOWN function. (jetty840)
...
Included AD595 calibration options. (daid)
13 years ago
4fbda5c3f5
Merge remote-tracking branch 'daid/Marlin_v1' into Test
13 years ago
35e57bf149
Added gen6 deluxe.
13 years ago
84ea2d61e8
Moved gen7 boards to motherboard type 10, 11 and 12.
...
Split ramps1.3 in Sprinter like config and multiextruder config.
13 years ago
01d28c18ab
Fixed casting warning in sanguino
13 years ago
2fd8c248fe
Added Fan control to the pre-heat settings.
...
I find that the PID routine works better when the cooling fan is switched on
at the beginning of a warm up routine. Otherwise when you enable the fan
just before a print, you have a delay as the PIDre-adjusts.
This should also be safer as most cooling fans are directed at the hot -ends
thermal barrier!
13 years ago
d9f2f509d5
Added new menu items under the prepare submenu.
...
Instead of a single pre-heat, now there is pre-heat ABS and PLA options
Added defines to the configuration file to adjust preheat temperatures for both
13 years ago
ae3e7586c6
Added HOME_POS. This adds the posibility to make the center 0
...
Updated the Xsteps ... settings via the LCD menu
13 years ago
8816ef1c64
Small fixes after merge
13 years ago
d298dd121f
merged SBUBA82 and Justblair
13 years ago
a05a261b72
Added a workaround. Ramps SD card does not have sdcarddetect. My temporary solution is to add a momentary swtich
...
that pulls down the SDCARDDETECT pin and mimicking the pull and reinsert ofa a SD card
13 years ago
1b6765ed12
Updated the pin config for RAMPS 1.3 to include ultimaker new style LCD/Rotary Encoder interface
13 years ago
e661578c84
support for GEN7 1.1,1.2 and 1.3
13 years ago
73344e69c1
Added temperature offset/gain settings for AD595.
13 years ago
d309565b56
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
13 years ago
0e3631ff4b
smaller changes
13 years ago
fa2e1be0ca
changed default EXTRUDE_MINTEMP to 170.
13 years ago
154de69c02
Print configuration.h version during startup (thanks hairykiwi)
13 years ago
9173a5713b
Teensylu support.
13 years ago
bdb70c0509
Warning for 10k thermistor
13 years ago
d8a0c6450f
Split the configuration file in two parts.
...
One for common settings.
One for advanced settings.
13 years ago
f9c5333f97
Made "stop heating wait" optional.
...
Default off.
13 years ago
13e2ad2831
- added info for using GEN7 configuration
13 years ago
9f139d6e0e
Added MAX6675 support. (Thanks to gregfrost)
...
Needs some work to remove the blocking in read max6675.
13 years ago
e45e5c68bb
Added support for Gen3+ (Pins file only)
...
Added late z enable. (blddk request)
Only calculate look ahead if >2 moves in buffer.
Removed some FORCE_INLINE to save memory.
Signed-off-by: Erik van der Zalm <erik@vdzalm.eu>
13 years ago
212515148e
added m240 photography support. default off
13 years ago
415aadf704
lcd panel bed support
...
advance and ultipanel not any more in default config
13 years ago
84d9cf7339
merging
13 years ago
e017228569
Merged multiple extruder support.
...
Soft PWM. (Sanguinololu can also have PID temperature control)
Interrupt save WRITE for addresses > 0x0FF
13 years ago
01001b89d2
repaired nozzle runout prevention to not collide with automatic stepper disabeling.
13 years ago
88ee053af0
heating up santity, formarly knows as "watchdog", but renamed due to the existance of the real watchdog, works now.
13 years ago
2bc5e7ec9e
prevent too long extrudes, or too cold extrudes
13 years ago
aa4f9a6474
better values.
13 years ago
87fd249c43
made runout prevention independent of tempeorarily set esteps
13 years ago
1ec0c3b68a
extruder runout prevention.
13 years ago
5b4625f79c
added a partial release option to "m84" aka "stepper release". If you do tiny layers, you might want to keep the z-axis powered to not loose height positioning after homeing.
13 years ago
4fd75dc813
Working version of multiple extruders (up to 3)
...
- The temperature control is pretty much complete
(not sure what to do w/ autotemp though)
Changed the pins assignment to clearly separate bed and extruder heaters
and temp sensors, changed a bit how termistor tables are handled.
- The steppers control is rudimentary
(only chanages what pins it uses depending on the active_extruder var,
but that's enough for switching extruder in the start.gcode in the
the profiles)
- Tested only w/ RAMPS 1.4
13 years ago
b99c49ec3b
Add option to only check endstop when homing
13 years ago
95a0b28acb
Merge branch 'Marlin_v1', remote-tracking branch 'origin/Marlin_v1' into Marlin_v1
13 years ago
af22e9cd38
Some advance modifications
13 years ago
4f909963e4
make QUICKHOME configureable
13 years ago
6b86f15686
More 2nd extruder implementation. (Not usable)
...
Advance (not tested)
13 years ago
59205ac5fc
preliminiary implementation for the early heating finish.
...
Might be replaced by something more clever, e.g. by erik, and does not yet support the second extruder or the bed.
its kind of not so cool, because you need 6 more ints.
Maybe isheating() should use the degrees directly, as it is not used in time-critical anyways.
Then it would be much easier. to have the offsets without additional variables.
13 years ago
f75f426dfa
Removed interrupt nesting in the stepper ISR.
...
Add serial checkRx in stepper ISR.
Copied HardwareSerial to MarlinSerial (Needed for checkRx).
13 years ago
aad4b75b94
First parts 2nd extruder
13 years ago
a0dc66f7bf
Home retract distance configureable per axis.
13 years ago
6d6f323535
make an option if sd-card stop should release the steppers.
13 years ago
74d0032e25
cooldown blocking selectable by #define.
13 years ago
c0f8c9fd72
Seperate ENDSTOP_INVERTING for X Y and Z
...
Added simple endstop filter.
Corrected M114 count display.
13 years ago
2e43f9c809
Changed min max temperature code.
13 years ago
8a1e719a3f
overworked config file
13 years ago
f52e1a9571
autotemp working, default=disabled.
13 years ago
70650c331d
corrected the ultimaker default values, the previous had a calculation error: see: http://groups.google.com/group/ultimaker/browse_thread/thread/91906788639703cf
13 years ago
b15902d3b5
Fixed bug in configuration.h
13 years ago
e63e224a33
Merge remote-tracking branch 'origin/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
Marlin/Marlin.pde
13 years ago
e7dca8614b
Advance experiments. Not working yet.
13 years ago
46f80e82d9
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
...
Conflicts:
Marlin/ultralcd.h
13 years ago
a9c7da06e3
and changed ultipanel to have the mm/sec and not mm/min
...
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
Conflicts:
Marlin/Marlin.pde
Marlin/ultralcd.h
13 years ago
7919a40d06
watchdog,percent done,
13 years ago
805d37f77b
Fixed some small planner bugs
13 years ago
5fd41ae872
Some fixes in planner
13 years ago
95126c09c0
Added slowdown
13 years ago
331e82dcd3
Buffer size > 16
13 years ago
c00eefb824
Merge remote-tracking branch 'origin/Marlin_v1' into Marlin_v1
13 years ago
1d0452f10c
250000 baud
13 years ago
c57906b627
fixed bug with adjusting ki in realtime.
13 years ago
ac82411c73
Merge remote-tracking branch 'origin/Marlin_v1' into Marlin_v1
13 years ago
65934eee9c
A lot of changes in the planner code
13 years ago
36958ee305
minor changes and first not-well working version of autotemp
13 years ago
27361e7cd0
beautified the config. ordered it into thematic sections.
13 years ago
d3bfffcb6e
Corrected thermistor naming
13 years ago
163efdf1c7
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
13 years ago
87aaf0f70a
static'ified Marlin.pde.
13 years ago
76b3f805c0
Added teensylu pins
13 years ago
1d171e9e52
reformating and some minor bugs/things found on the way.
13 years ago
2afb7bd4cf
refactured temperature.cpp so that there are now abstract functions to access temperatures.
13 years ago
0b82465168
First arcs version. (Arcs not working ok)
13 years ago
2e8e8878e5
Corrected temp variables.
13 years ago
04d3b5537f
Merge remote-tracking branch 'origin/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
Marlin/EEPROMwrite.h
Marlin/Marlin.h
Marlin/Marlin.pde
Marlin/temperature.cpp
Marlin/temperature.h
Marlin/thermistortables.h
13 years ago
d15f01e1b4
Temperature changes
13 years ago
00674af3a8
merge from the branch bkubicek/Marlin/zalmmerge
13 years ago
95d3d9847c
M109 now equal to sprinter
13 years ago
bf879ceaa9
Added thermistor tables
13 years ago
094afe7c10
Merged Marlin, Marlin non gen6 and Ultimaker changes
13 years ago
8e017b81ab
Sync with non-gen6 version
13 years ago
b5f6482dce
Fixed small feedrate bug.
...
Copied Camiels comments in the Configuration.h file
13 years ago
26bf57e22c
first-commit
13 years ago
750f6c33e3
first commit
13 years ago
cocktailyogi