42fb7c14b0
Update the sdcard usb sharing config and apply to Re-ARM
6 years ago
254b68fe2c
servo update
6 years ago
870bfd08f5
usb and sdcard sharing improvements
...
* Add traceback after watchdog timeout
Add the cpability to perform a traceback following a watchdog timeout.
* Enhanced hardware SPI
Allow use of either SSP0 or SSP1.
Ensure that no data is left in I/O buffers after calls to enable sharing of SSP hardware.
* Make flash emulation of eeprom the default
Make use of flash for eeprom storage the default. This means that usage of eeprom will not cause USB drive mount/unmount operations.
* Allow sharing of SD card
SD card I/O operations from the USB stack take place in idle loop, rather than at interrupt time. Allowing sharing of the SPI bus.
New configuration options to allow usage of the SD card to be specified.
* Fix problem with hardware SPI pins
6 years ago
5ddf52d58e
[HAL][LPC176x] Pull out framework into separate repository
...
Framework and build platform now located at https://github.com/p3p/pio-framework-arduino-lpc176x and https://github.com/p3p/pio-nxplpc-arduino-lpc176x respectively
fix mkssbase leds
move hardware serial
remove hardware/software serial
Hardware Serial extraction
HardwareSerial ISRs
fix disabled serial2 causing Serial object to link
move usb devices out to framework
separate out adc/pwm peripheral function from hal.cpp
fix includes
remove unused pwm init
move adc
HAL header update
templated filtered adc
LPC1769 platform
6 years ago
213e94bce2
[2.0.x] Updated slovak translation ( #12059 )
6 years ago
a40458405a
Fix datasize error when FWRETRACT is disabled ( #12086 )
6 years ago
951b25163e
Extend M217 with configurable park/raise ( #12076 )
6 years ago
ea13a77dcb
Fixed Z-Probes NO/NC for Anycubic Kossel ( #12083 )
6 years ago
ab9d5eb38d
Add Bootscreen Animation ( #12077 )
6 years ago
26208a5c2f
Clean up some boot screens
6 years ago
9b6be0ae0f
Fix lite status screen SD %
6 years ago
af3bf6c956
Tweak config spacing
6 years ago
a44ef27897
Outdent singlenozzle toolchange code
6 years ago
d338e4d875
Fix singlenozzle toolchange cold extrusion test
6 years ago
25b980dddb
Remove erroneous Pin 12 definition
...
There is no switchable Power Supply. Don't put it on Pin 12.
(Pin 12 is actually FAN1)
6 years ago
ddaef1a60c
Clean trailing whitespace
6 years ago
1407afad73
Move SENSITIVE_PINS to its own file
6 years ago
45e738876a
Add stepper MS3 support
...
Co-Authored-By: TheLongAndOnly <thelongandonly@users.noreply.github.com>
6 years ago
d43d4e4219
Refactor PRINTER_EVENT_LEDS, apply to M303 ( #12038 )
...
Co-Authored-By: Giuliano Zaro <gmagician@users.noreply.github.com>
6 years ago
d8d76cd2ba
[2.0.x] Italian language update ( #12060 )
6 years ago
e8d2cf4fb5
EEPROM followup (tmc_stepper_current_t)
6 years ago
50cbca4c55
Hide some menu items when busy
6 years ago
3cb5517ddb
Make singlenozzle tool-change honor no_move ( #12056 )
...
...Set no move earlier so it applies
6 years ago
d332fcb8fa
Fix firmware-retract compile errors ( #12061 )
6 years ago
43940d59ed
Fix trailing spaces
6 years ago
b2c1cd7eda
Allow cold change of active extruder ( #12055 )
...
Followup to #11994
6 years ago
d556dc1865
Fix and improve EEPROM storage ( #12054 )
...
* Clean up Temperature PID
* Improve EEPROM read/write/validate
* Group `SINGLENOZZLE` saved settings
* Group planner saved settings
* Group filament change saved settings
* Group skew saved settings
* Group `FWRETRACT` saved settings
6 years ago
9b5c1a5e77
Fix EEPROM checksum bug
...
Addressing #12048
6 years ago
272d4a5167
Apply #pragma once
6 years ago
07d33849b0
Fix unused var warning, apply ENABLED
6 years ago
a3e8cb1e44
[2.0.x] Ender-4 small improvements in Configuration ( #11843 )
6 years ago
cf5284cdf2
Add SD Firmware Update capability ( #12043 )
...
Co-Authored-By: timoxd7 <timoxd7@users.noreply.github.com>
6 years ago
0bd54392b7
Use uint8_t in EEPROM code
6 years ago
ce82015d5f
Fix include in G80
6 years ago
cef1de89d0
Fixed incorrect axis index. ( #12051 )
6 years ago
d6d48e63fb
Allow #defined TYPE arg to ultralcd menu macros ( #12041 )
...
Previously, it was not possible for the TYPE argument to ultralcd menu macros to itself be a #defined value. This made it difficult to create variables to set many related menu items to a common precision that could be easily changed.
6 years ago
2ef7175b42
Update Ender-2 BED_MAXTEMP ( #12042 )
...
Also added details to the README to make sure the Ender-2 status is properly documented.
6 years ago
5f6aabccbe
Tweak M48 spacing
6 years ago
ec9aa4f468
[2.0.x] Miscellaneous fixes ( #12039 )
...
* Allow override of soft SPI pins in `pins_*.h`
* Add default case to avoid compiler warning.
* Additional pin definitions for Archim 2.
* Einsy Retro has same timings as Einsy Rambo.
6 years ago
906a24fa81
Extensible user interface API ( #11193 )
6 years ago
ee253991d4
Various fixups for single-nozzle filament swap ( #12036 )
6 years ago
8dbb305e8e
Fix "Missing separator" errors. ( #12035 )
...
- Makefiles require tabs (not spaces) before shell commands.
- Other indentation can either be space or tabs.
6 years ago
55e810d512
Fix G80 compilation
6 years ago
d5017e2788
Add status screen with 4 nozzles
6 years ago
7db0113b53
Improve E_AXIS_N macro
6 years ago
191df5e17d
Correct PWM_PIN behavior for STM32 HALs ( #12027 )
6 years ago
f2ecf8d510
Add option to control Solenoids under PARKING_EXTRUDER ( #12028 )
6 years ago
74cd6cb4fc
Single nozzle filament change ( #11994 )
6 years ago
bfcf570d68
Try ISR_ALIASOF for Endstop Interrupts
6 years ago
c0d9058e25
Shorten an Italian menu title ( #12034 )
...
…and change a multi-use "back" menu item.
6 years ago
dffb4c63dc
[2.0.x] TMC2660 followup ( #12029 )
...
* Don't react to s2g on TMC2660. False positives
* Init with sensorless probing as well
6 years ago
d6b0fbd771
Use uint8_t for all fan speeds ( #12032 )
6 years ago
cb7844c8d4
Save PROGMEM on serial prefixes ( #12033 )
...
With default config and `EEPROM_SETTINGS`, saves over 200 bytes of PROGMEM.
6 years ago
07db08e39d
Fix EXTRUDER_AUTO_FAN_SPEED comment
6 years ago
ca0e308105
Fix up some units comments
6 years ago
65b8f3821b
Suppress temperature.h compile warning
6 years ago
c447d75916
Add support for TMC2660 ( #11998 )
6 years ago
cf0b9eb37c
no need to use destination in do_pause_e_move
6 years ago
e8d677620c
Use NUM_SERVOS in EEPROM code
...
Fix #12015
6 years ago
0fcdfdeed6
Followup to #12017
6 years ago
acac2adfc8
Add support for MeCreator2 ( #12017 )
6 years ago
49823a4939
Fix broken jerk handling ( #12019 )
...
Fix #12004
6 years ago
52a37913c1
Extend and apply some corrections
6 years ago
77b9a41f1f
Add G-code extensions to example configs
6 years ago
e09c144674
Add CNC-like G-code options
6 years ago
33056046a3
STM32 non-generic PWM_PIN and USEABLE_HARDWARE_PWM ( #12016 )
6 years ago
d5141c4e03
Fix up leading/trailing whitespace
6 years ago
03fc4d31d0
Makefile support for 32-bit Archim board and new TMC library ( #11997 )
...
* Support new TMC library and 32-bit Archim board
- Added IS_MCU flag
- When IS_MCU flag is 1, AVR compiler will be used
- When IS_MCU flag is 0, ARM compiler will be used
- Added support for new TMC library
- Added support for a 32-bit Archim board, which could probably be used as a basis for other 32-bit boards.
6 years ago
65b36642f8
Fix Anycubic Kossel config
6 years ago
fc326b3dde
Add USB_FLASH_DRIVE_SUPPORT to examples
...
Co-Authored-By: marcio-ao <marcio@alephobjects.com>
6 years ago
2067619a26
Add USB_FLASH_DRIVE_SUPPORT
6 years ago
07fe8d28be
[2.0.x] Partial Italian revert ( #12008 )
...
- Use a comma for decimals just in one message has not been a good idea.
- Full comments translation
6 years ago
517b4f4cd4
Fix lightweight UI hotends display
6 years ago
72a750e0eb
[2.0.x] Update Italian language ( #11996 )
6 years ago
bb561baf9e
Tweak some config comments
6 years ago
fcf6d127fd
STM32 timer simplification ( #11995 )
...
Prescalers aren't calculated for the given target frequency.
Stepper timer should run at 2 Mhz and temperature timer at 72 Khz.
6 years ago
8daadd2c8c
Fix TMC_DEBUG undefined report_tmc_status ( #11993 )
6 years ago
c40ea1f0fd
Update EEPROM_VERSION
...
And set EEPROM_OFFSET to 0, since the historical 100 skipped bytes are never used.
6 years ago
1358bd9319
Make MAX_EXTRUDERS always 6
6 years ago
001f26b642
Template struct simplification for serial ( #11990 )
6 years ago
348004c34f
STM32F7 HAL using the official STM32 Arduino Core ( #11750 )
6 years ago
3e58b3a5d4
Followup to #11943
6 years ago
c3229e1b34
Migrate to a new TMC library ( #11943 )
6 years ago
2abf3d258d
Korean language translation support ( #11987 )
6 years ago
d6955f25b2
Expand serial support in DUE/AVR hals exploiting the templated MarlinSerial classes ( #11988 )
6 years ago
f6f2246f59
Templatized serial classes ( #11982 )
6 years ago
ee53f7d813
Revert header reorg.
6 years ago
d619ba2685
Tweak STM32F4 config
6 years ago
d777cef837
fixed minimum macro ( #11986 )
6 years ago
e3f7b69105
Add PROBING_STEPPERS_OFF ( #11984 )
...
Co-Authored-By: houseofbugs <houseofbugs@gmail.com>
6 years ago
0e5bcdf695
Make DISABLE_INACTIVE_EXTRUDER a simple switch
6 years ago
0dedb3e139
Reorganize some core headers ( #11983 )
6 years ago
ab4549d2bc
[2.0.x] Add simultaneous retraction for mixing extruder ( #11941 )
6 years ago
c75f5a376b
Tweak some comments
6 years ago
f4c625d3a1
Ensure MIN/MAX overrides
6 years ago
3019713402
Reorganize some enums
6 years ago
606a4362b3
Reduce STM32F4 compile warnings
6 years ago
b3154b2120
Apply MOVE_Z_WHEN_IDLE to example configurations
...
Co-Authored-By: dot-bob <gibben@gmail.com>
6 years ago
b0fd8f2d74
Add option to move Z on double-click when idle
6 years ago
389376c40e
Clean up softspi.h
6 years ago
e78bdd654d
Clean up BABYSTEP options
6 years ago
8ae113ff36
Show zprobe_zoffset when BABYSTEP_HOTEND_Z_OFFSET is disabled ( #11973 )
6 years ago
2e98437392
Clean up main menu ( #11972 )
6 years ago
6d862b2916
Home before level corners, if needed ( #11976 )
...
…and add a consistent homing screen for all LCD pre-homing.
6 years ago
11ac75edcb
Use PGM_P for PSTR pointers ( #11977 )
6 years ago
4d5566a6b7
Add filament runout sensor menu item ( #11971 )
6 years ago
8489673cea
Adjust some HAL formatting
6 years ago
fb8a07660a
Followup to minmax patch
...
Co-Authored-By: Palatis <palatis@gmail.com>
6 years ago
3c40933713
Remove trailing spaces, old comment
6 years ago
a3ec805c97
Anycubic Kossel Linear+: corrected DELTA_DIAGONAL_ROD ( #11964 )
6 years ago
b30ca652ae
Replace MIN# / MAX# with variadic MIN / MAX ( #11960 )
6 years ago
e10f730478
Tweak vector_3::apply_rotation
6 years ago
e2ab78d876
Fix SERIAL_PORT_2 sanity check
6 years ago
a644d8cb93
Avoid copies in vector and matrix ( #11959 )
6 years ago
693865a649
Fix some whitespace
6 years ago
9903305dda
Merge pull request #9582 from tcm0116/2.0.x-sensorless_probing
...
[2.0.x] Add TMC2130 sensorless probing
6 years ago
14df753086
Correction for block->mix_steps
...
Fix #11484
6 years ago
2ecfda80ac
Improve support for JTAG/SWD pins reuse ( #11963 )
...
STM32 can reuse JTAG and SWD pins separately. Add `DISABLE_DEBUG` option to disable both interfaces and retain `DISABLE_JTAG` to disable JTAG only.
6 years ago
bb47009656
Apply sensorless changes to example configs
6 years ago
3286325044
Add TMC2130 sensorless probing
6 years ago
7d5c336c56
Corrections for dylsexic TMC
6 years ago
d89d8fe852
Fix Busy State in temperature.cpp
...
Fix #11954
6 years ago
70e7a465d8
[2.0.x] Fix compile error ( #11951 )
...
Fix compile error intruduced with M109 modification
6 years ago
935b120949
Anycubic Kossel: probe closer to the edge ( #11950 )
6 years ago
1410e79e7f
Ensure M109 handles autotemp
6 years ago
e4389f7d23
Standard methods to wait for heating ( #11949 )
6 years ago
bdc9889d3a
Fix a sanity check
6 years ago
321f9140d1
Followup to #11904
6 years ago
23114aeb81
Fix garbled M119 output. Honor NUM_RUNOUT_SENSORS ( #11948 )
6 years ago
1667ed9d1c
Pause should use ECHOLNPGM
6 years ago
93839e2f73
Add option to enable/disable autoretract altogether ( #11904 )
6 years ago
ad21a4f07b
Tweaks to HAL format and order
6 years ago
b682a1961a
Tweak STM32F7 TMC2660 class
6 years ago
a0a3b23e35
Reduce Raptor bootscreen by 144 bytes
6 years ago
95d793456b
Add Formbot Raptor config, fix other Formbot configs ( #11926 )
6 years ago
d016b572e3
[2.0.x] Add pin configuration for Fysetc F6 ( #11932 )
6 years ago
84926b1d5a
HAL general support for DISABLE_JTAG option ( #11211 )
...
Some STM32-based boards may use multiplexed JTAG pins as IO. Up to now the `DISABLE_JTAG` option (defined in pins files) was only supported for AT90-based boards. This commit generalizes the code and adds support for boards based on STM32F1 and STM32F4.
6 years ago
c575c5d5f6
Bring example configs up to date ( #11939 )
6 years ago
6b1a4f30a8
Fix case of T-Rex 3 _Statusscreen.h
6 years ago
ab7bfa86e2
Fix case of T-Rex-3 _Statusscreen.h
6 years ago
241168926d
Update some configs
6 years ago
cb6454118c
Workaround for Pronterface M29
6 years ago
eeab4141db
[2.0.x] Anycubic Trigorilla 14 pins tweak ( #11869 )
6 years ago
cb9dc56630
Add GT2560 v3 support ( #11914 )
6 years ago
f2e630a05e
Stow probe on probing failed ( #11936 )
...
Prevents probe from being left down should probing fail and print job continue
6 years ago
0b602ae101
[2.0.x] Fix Anycubic Kossel with Probe V1, stuck LCD message after stow ( #11929 )
6 years ago
dc11131656
[2.0.x] fix possible race condition ( #11923 )
...
Fix some commits done in #11900
6 years ago
d6b9327c11
Followup for Endstop Noise Threshold
...
Followup to #11912
6 years ago
aa6e8e9325
Tweak some config comments
6 years ago
5490a664f5
Expose: Homing Validation and Endstop Noise Threshold ( #11912 )
6 years ago
cee34f7290
Followup for BABYSTEP_HOTEND_Z_OFFSET ( #11916 )
6 years ago
884ad75cb8
Update config files
6 years ago
18e456d38d
[2.0.x] fix home endstop bug (DON'T MERGE, needs discussion) ( #11900 )
6 years ago
6742026568
Followup for 6 extruders
6 years ago
04bdff4115
Add a blank line
6 years ago
ccbd045f02
Fixed warning about comparing signed to unsigned ( #11909 )
6 years ago
1104054d73
2.0 IDEX Independent z offset and other fixes ( #11862 )
...
* Add Formbot Raptor board
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>
* Add a second Z probe Z offset
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>
* Modify method to utilize live adjustment of hotend z offset
Should probably move config option to babystepping and rename as it may now apply to all multiextruder systems
* Move config item and catchup other code to current method
6 years ago
217e0efd20
General option PAUSE_BEFORE_DEPLOY_STOW ( #11905 )
6 years ago
849dea92a8
Move probe extras below probe types
6 years ago
a2b0260f0f
Update Sublime files
6 years ago
a4cdffdd69
Support for manually deployed fixed probes ( #11899 )
6 years ago
ddcbf80f23
Followup for Z_TRIPLE_ENDSTOPS
6 years ago
c411e7eb0d
[2.0.x] Squelch compiler warnings seen with -Wall ( #11889 )
6 years ago
83105590a0
Better default values for Mesh Inset
6 years ago
4163c1a514
Fix end stop and Z-probe reporting logic
6 years ago
ea9eb2fc8f
Fix servo angles in config-store
6 years ago
d3d6be8210
Add MAX7219 reverse units option ( #11860 )
6 years ago
beab9733f8
Remove extra clauses in config-store
6 years ago
5a74b12b45
Followup to #11769
6 years ago
f38570ac55
Add custom user menu title ( #11769 )
6 years ago
17494099a9
Fix parking_extruder_tool_change
...
Fix #11872
6 years ago
140caf99b8
E0_CS_PIN moved from A13 to A15 on RAMPS-FD v2.2 ( #11865 )
6 years ago
10590c2f80
Fix some fan conditionals
6 years ago
e4ee607fc8
Fix Dual X FRS in M600
...
Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>
6 years ago
bae8f82ba8
[2.0] Fix Mixing Extruder mixing factors ( #11861 )
6 years ago
c5e5cc5e9f
Fix some trailing whitespace, macros
6 years ago
54bd124665
2.0.x: Fix normalize_mix() ( #11856 )
...
Mix factors needed to be updated consistent with the recent Stepper/Planner code refactor.
6 years ago
5fbfbde532
Fix example file to pull in correct pins file
6 years ago
378f354939
IDEX Scaled Duplication is still under development
...
Take it out of the menu until it is tested and working.
6 years ago
65045ba54b
tmc_util fix part 2
...
Followup to 115abf9
6 years ago
09a2bee8aa
Support more filament runout sensors in M119 ( #11851 )
6 years ago
115abf9c53
Fix syntax error in front of `tmc_axes`
6 years ago
0780913848
IDEX Improvements ( #11848 )
6 years ago
39732838b4
Tweak indent of Chinese languages
6 years ago
53bd0b55cb
Followup for 6 extruders
6 years ago
1718eff54a
Code changes supporting up to 6 extruders
6 years ago
f5c210d33d
Config changes supporting up to 6 extruders
6 years ago
d948c6e867
RADDS Extension Board V3 support
6 years ago
c437bb08f1
Overhaul of the planner ( #11578 )
...
- Move FWRETRACT to the planner
- Combine leveling, skew, etc. in a single modifier method
- Have kinematic and non-kinematic moves call one planner method
6 years ago
8323a08642
Clean up some whitespace
6 years ago
6286afd456
Add Triple-Z options to example configs
6 years ago
1a6f2b29b8
Add support for Triple-Z steppers/endstops
6 years ago
bc06406d7d
Fix Anycubic Kossel config (probe crash) ( #11832 )
6 years ago
66f83d33e6
Fix some config comments
6 years ago
84ed9b5a63
Send "G33 S P1" for Delta Height Calibration ( #11831 )
6 years ago
215eee4fe5
Use 'friend' to access set_directions
6 years ago
ff51e7322d
Fix for Stepper::set_directions() compilation error ( #11838 )
6 years ago
809b232fa2
Fix stepper directions after M501/M502
...
See https://github.com/MarlinFirmware/Marlin/issues/11103#issuecomment-421387611
Co-Authored-By: tcm0116 <tcm0116@users.noreply.github.com>
6 years ago
f79a5a9dee
Tweak spacing of L6470 options
6 years ago
c37d3ae97d
[2.0.x] Fix NOZZLE_PARK_FEATURE for Anycubic Kossel ( #11812 )
6 years ago
Christopher Pepper