1fad8e6a81
Proper long file name var
10 years ago
29e854c535
Disable SDCARD_SORT_ALPHA by default
...
For legacy boards it’s better if this option is disabled.
10 years ago
6599adc184
Polish up a little...
10 years ago
a12eec33e2
Completed SORT_USES_MORE_RAM implementation
...
For the MORE_RAM option we need to buffer both the short and long
names, even though long names are sometimes redundant. Worst case, all
the names are max length. We can save some RAM by not storing these. We
could save more RAM by only storing the visible part of the long name.
10 years ago
c9486ebb85
Improvements, more SORT_USES_MORE_RAM
...
With this option, always keeps the dir in RAM, doubling as a cache for
getfilename. A board with only 8K of SRAM is cutting it very close.
10 years ago
b6ffea612a
Expand on More RAM concept, address minor bugs
10 years ago
8196b36ad9
SD Card Alpha Sorting
...
First iteration of alphabetical sorting for SD cards, both
slow+efficient and fast+rammy. Option for folders to sort first, last,
or not at all.
10 years ago
cf749dbeda
Completed SORT_USES_MORE_RAM implementation
...
For the MORE_RAM option we need to buffer both the short and long
names, even though long names are sometimes redundant. Worst case, all
the names are max length. We can save some RAM by not storing these. We
could save more RAM by only storing the visible part of the long name.
10 years ago
ae081d0fe0
Improvements, more SORT_USES_MORE_RAM
...
With this option, always keeps the dir in RAM, doubling as a cache for
getfilename. A board with only 8K of SRAM is cutting it very close.
10 years ago
785143a013
Expand on More RAM concept, address minor bugs
10 years ago
0cbbba08bd
SD Card Alpha Sorting
...
First iteration of alphabetical sorting for SD cards, both
slow+efficient and fast+rammy. Option for folders to sort first, last,
or not at all.
10 years ago
3ebfd29312
Print a message when printing is aborted
...
Messages in gcode files like “M117 Printing…” were not being cleared on
Stop Print.
10 years ago
2ef0669b19
Split do_blocking_move() to XY and Z sections to make sure that the Z homing feedrate is not exceeded
10 years ago
64139f5e5a
Merge https://github.com/ErikZalm/Marlin into Marlin_v1
10 years ago
edfcf3b527
Toshiba Stepper Driver support
...
Tosh stepper drivers need to be driven slower, so the stepper code
was interleaved to separate the pin HIGH from the pin LOW. This adds
enough instructions to make it work, without needing nops.
10 years ago
c429a4b3ec
Toshiba Stepper Driver support
...
Tosh stepper drivers need to be driven slower, so the stepper code
was interleaved to separate the pin HIGH from the pin LOW. This adds
enough instructions to make it work, without needing nops.
10 years ago
1977b4490f
Merge pull request #1159 from thinkyhead/lcd_wait_better
...
M0/M1 Message Fix
10 years ago
7562183efc
Skip over spaces first
10 years ago
5a8b3a84ae
Merge pull request #1155 from thinkyhead/lcd_wait_better
...
M0-M1 Enhancements
10 years ago
433ac29d31
Updated a bit of spanish language
10 years ago
12b51d6060
Ignore S and P if no value >0 is included.
10 years ago
d12b24758a
Clear LCD to welcome_msg if not printing
...
The welcome message is more appropriate than “resuming print” if
nothing is printing.
10 years ago
3f54c9ba33
Relocate click ignore code into info screen
10 years ago
92e21d3ee2
M0-M1 Enhancements
...
Allow M0 and M1 to include a message string. Ignore clicks on “Wait for
user” so that the Info Screen stays up.
10 years ago
0d35b1d0b8
Allow negative values in menus
10 years ago
0d97dec434
Adaption of LCD info screen
...
Here comes a compile-time operation to match the extruder symbols on the
info screen to the set number of extruders in configuration.h.
When only one extruder is selected, the "1" on the symbol will not be
displayed.
10 years ago
3b1ab84536
Display Filament Sensor data on graphic LCD
...
Added support to show the filament width on the status line of the
graphic LCD. The status will show for 5 sec and then switch over to
data. Status can be seen by clicking the button.
10 years ago
d84934d8c5
Display Filament Sensor data on 20x4 LCD
...
Changes to support displaying the real-time filament width and the
volume factor on a 20x4 LCD. The data is displayed on the 4th line.
First the status message is displayed for 5 seconds, and then the
filament data is displayed. The status message can be seen by
re-selecting the info screen in the menu.
10 years ago
5c8107bcdd
Commented out FILAMENT_SENSOR #define
...
Commented out the FILAMENT_SENSOR define so that it is not enabled by
default. Code does not work on all hardware variants.
10 years ago
377dfb182f
Updated example configurations for Delta printers
10 years ago
b81021f475
Merge https://github.com/ErikZalm/Marlin into Marlin_v1
10 years ago
724197454c
Merge pull request #1104 from ch100/Marlin_v1
...
Fixed typo.
10 years ago
058e446531
Merge pull request #1037 from filipmu/Filament-Sensor
...
Support for a filament diameter sensor
10 years ago
110c5dcf23
Fixed typo.
...
Signed-off-by: Christian Inci <chris.pcguy.inci@gmail.com>
10 years ago
ca30aee903
Fix "add_homeing" to "add_homing" to match changes
10 years ago
0733825fb1
Merge pull request #1099 from Fourmi/Marlin_v1
...
Update line 627 ,wrong number on thermistortables
10 years ago
af3e4d7510
Update line 627 ,wrong number on thermistortables
...
Wrong number on line 627 > i change number "12" by the correct number "13"
Soory
10 years ago
aaaf8fe8dd
Merge pull request #1068 from darkjavi/Marlin_v1
...
Added profile for RAMPS with 2 extruders and 1 fan, no heated bed
10 years ago
b360306881
Merge pull request #1073 from WingTangWong/wing-fix-float-delta
...
Wing fix float delta
10 years ago
ce85515428
Merge pull request #1082 from Fourmi/Marlin_v1
...
Add thermistor table
10 years ago
764921bdbf
Merge pull request #1091 from Aldert/patch-1
...
Update motion_control.cpp
10 years ago
c40c7b589b
Merge pull request #1095 from thinkyhead/codeclean
...
Simple code cleanup. Rename "homeing" to homing.
10 years ago
0f2e0525df
Merge pull request #1096 from thinkyhead/set-home
...
Proposed feature: Set Home Offsets
10 years ago
5ae02a361b
Merge pull request #1097 from thinkyhead/round-up-xyz
...
Adjust the Z display to hide float rounding errors
10 years ago
fb34265d75
Make hotend optional when compiling with lcd support
...
Signed-off-by: Matthew Schick <matthew.schick@gmail.com>
10 years ago
6e343ef2f0
Adjust the Z display to hide float rounding errors
10 years ago
2f6c57eadc
Proposed feature: Set Home Offsets
...
Add an item to the LCD menu that applies the current axis position to
the “add_homeing” offset.
10 years ago
f989bd5435
Simple code cleanup. Rename "homeing" to homing.
10 years ago
6c5a460e65
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
10 years ago
d1e4237e1d
Update motion_control.cpp
...
G03 Full circle did not work (G02 is working correct)
10 years ago
a664763e6f
Update thermistortables.h
...
Add another thermistor table (13),it's a cartridge thermistor up to +300°C,use with Hotend "Simple ONE" & "All In ONE"
Thx
10 years ago
b5dc228a7a
Update configuration.h
...
Add another comment for thermistor 13 ,use with Hotend "Simple ONE & All In ONE"
10 years ago
3cbb2f56c6
Update configuration.h
...
Add another comment on configuration.h for the value of thermistor.
I make a pull request on thermistortables.h with my thermistor (12),but y see there is a comment on configuration with number 12 but it's not present on thermistortables.h ?
Thx
10 years ago
c35736a140
Update thermistortables.h
...
Add another thermistor table,use with hotend "Simple ONE" & "All in ONE"
10 years ago
cb4a6dd2dc
Merge pull request #1065 from oliasmage/Marlin_v1
...
Corrected retract() call for use of auto probe without sled enabled.
10 years ago
01e9b536cb
Fix build for non-sled bed auto levelling
...
This function should only be used with sled, not all bed auto
levelling.
10 years ago
58eabd21fb
Added ifndef
10 years ago
88d12a762a
Added #ifndef DELTA wrapper to float delta
10 years ago
bf0ecedf60
Merge pull request #1051 from fsantini/EZ_fix935
...
Fix issue 935: error in matrix calculation
10 years ago
40ba644bb4
Added profile for RAMPS with 2 extruders and 1 fan.
...
modified: Marlin/Configuration.h
modified: Marlin/pins.h
10 years ago
3b8216bdd1
Corrected #endif and ifdef for Z_PROBE_SLED code.
10 years ago
37799f70ba
Corrected retract() call for use of auto probe without sled enabled.
10 years ago
1632e5e38a
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
10 years ago
fe3a09bbcf
Correct analog sampling time for additional A to D sample
...
Adjusted the #define PID_dT to reflect 10 A to D sample steps, vs
original 8.
10 years ago
1e9dc85148
Do not use translations for the serial console messages
...
The serial protocol has to stay machine readable, without having
to cope with a ton of different human language variants. So
just leave it at the original english version.
Should fix ErikZalm/Marlin#1052
10 years ago
cf325ba240
Fix issue 935: error in matrix calculation
10 years ago
018b68a5c4
Merge pull request #976 from cocktailyogi/SCARA_by_Yogi
...
Implemented SCARA-Maths
10 years ago
dde61d8886
Merge pull request #977 from OskarLinde/Marlin_v1
...
Fix lcd itostr3() to handle negative numbers
10 years ago
0fbfb1bf82
Merge pull request #991 from bonm014/patch-1
...
Leapfrog controller board support
10 years ago
8340ca6e05
Merge pull request #992 from Grogyan/patch-1
...
temperature.cpp fixes for SD card and MAX6675
10 years ago
9887555192
Merge pull request #998 from darconeous/pull-requests/fwretract
...
FWRETRACT fixes
10 years ago
105571ec68
Merge pull request #1005 from midopple/Marlin_v1
...
With option DISABLE_INACTIVE_EXTRUDER the extruder is disable to early
10 years ago
68dd5e635e
Merge pull request #1024 from oliasmage/Marlin_v1
...
Adding Z Probe via sled mounted endstop
10 years ago
25069ed4e9
Merge pull request #1031 from Roxy-3DPrintBoard/Z_PROBE_REPEATABILITY-with-correct-Defaults
...
Z probe repeatability with correct defaults
10 years ago
75b3a68b65
Revert "Change pinMode to SET_INPUT or SET_OUTPUT"
...
This reverts commit 1d0fe035f3
11 years ago
e3c88a5120
Filament sensor changes to config file
...
Update the config file for improvements and clarifying what diameter to
use in the slicer software.
11 years ago
62db9848d3
Improvements and bug fixes in sensor delay buffer for filament sensor code
...
Improvement to avoid reinitializing delay buffer with every print. Fixed
issues in buffer indexing and memory out of bounds due to floating point
imprecision. Simplified the code by avoiding conversion to standard
diameter and 1cu mm extrusion, which caused complications in determining
mm extruded.
11 years ago
5908fd5cec
Fix reseting CHDK pin to LOW
...
chdkActive was set to false regardless of (millis() - chdkHigh) being bigger than the CHDK_DELAY or not. So if (millis() - chdkHigh) wasn't bigger than the delay the first time, the CHDK would never be set back to LOW.
Also, don't return from the function, as there might be other stuff to do, after the CHDK check.
11 years ago
0adbc79571
Fix Default Configuration so Auto Bed Leveling is off
...
This snapshot has the Auto Bed Leveling turned off because most Marlin
users do not have that feature.
11 years ago
0091865583
Z_PROBE_REPEATABILITY test
...
Z_PROBE_REPEATABILITY test for Auto Bed Leveling.
Implemented as M48 with extra user specified options.
Full support at
http://3dprintboard.com/showthread.php?2802-Auto_Bed_Leveling-Z-Probe-Repeatability-code
11 years ago
85649a4549
Real-time filament diameter measurement and control
...
This feature allows the printer to read the filament diameter
automatically and adjust the printer in real time. Added code to read
an analog voltage that represents a filament diameter measurement. This
measurement is delayed in a ring buffer to compensate for sensors that
are a distance away from the extruder. The measurement is used to
adjust the volumetric_multiplier for the extruder. Some additional g
codes (M404, M405, M406, M407) are used to set parameters and turn
on/off the control. g code M221 is updated. Pins for RAMPS1.4, RAMBO,
and Printrboard are identified for analog input. The configuration file
is updated with relevant user parameters.
11 years ago
1d0fe035f3
Change pinMode to SET_INPUT or SET_OUTPUT
...
Original code is using WRITE from fastio, but original used pinMode to
set pin direction and did not use the fastio SET_INPUT or SET_OUTPUT.
This caused an issue with the rotary encoder interface to boards based
on teensyduino, since for teensyduino pin numbers for fastio and the
usual Arduino IO are different.
11 years ago
e7707aedbc
Commented out new #defines in Configuration.h.
11 years ago
0a8dc0e96b
Added documentation to the README.md for the sled Z probe option. CAB
11 years ago
d2fcb3ee56
CAB: Added code for Z-probe with Z endstop mounted on a sled.
11 years ago
3cd7dbcc45
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
c13a831ea1
Merge pull request #1017 from foosel/fix/checksum_truncation_bug
...
Fix for a wrong checksum truncation for certain commands
11 years ago
2d22902d08
Fix for a wrong checksum truncation for certain commands
...
Positioning of string terminator to truncate checksum from the commands
M23, M28, M30, M32, M928 and M117 was off by one, causing the last
letter of the actual command to be truncated instead of just the
checksum.
In case of the SD commands this caused checksummed commands targeting
existing files to fail since the last letter of the filename was
truncated.
In case of M117 this caused the last given letter not to be displayed.
This patch fixes the off-by-one error and sets the null terminator
on the exact position of the * starting the checksum instead of the
character before that.
11 years ago
ad3b770c1a
updated examples
11 years ago
2f4a20257c
imported last Marlin changes
11 years ago
aacff0d361
Merge pull request #948 from Dim3nsioneer/Marlin_v1
...
Implementation of FW extruder change retract
11 years ago
17aa67e4ea
If the option DISABLE_INACTIVE_EXTRUDER ist active the extruder switch to early to inactive because there are some moves in the buffer. So the planner wait 32 moves to disable the unused extruder.
11 years ago
1fd9a7d476
Fix for FWRETRACT on DELTA printers.
...
Fixes #817
11 years ago
3f2c771d90
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
bcd039aa81
Update pins.h
11 years ago
82606354dd
Update temperature.cpp
...
Enables both SD card and MAX6675 to talk with each other
Fixes also issue #750
11 years ago
32a6451ad8
Add leapfrog and dual Y/Z
...
I have added the pin set for the leapfrog and the support of dual Y and Z
11 years ago
b5417be109
Update Configuration.h
...
Leapfrog added to the board list
11 years ago
f244045245
Update pins.h
...
Leapfrog board added to the pin list
11 years ago
2242a84218
Changed the declaration of the variable to Marlin_main.cpp to fix issue on commit #965
11 years ago
6e3406d228
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
43c298a7a9
Add "Thermal Runaway Protection" feature
...
This is a feature to protect your printer from burn up in flames if it
has a thermistor coming off place (this happened to a friend of mine
recently and motivated me writing this feature).
The issue: If a thermistor come off, it will read a lower temperature
than actual. The system will turn the heater on forever, burning up the
filament and anything
else around.
After the temperature reaches the target for the first time, this
feature will start measuring for how long the current temperature stays
below the target minus _HYSTERESIS (set_temperature -
THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
If it stays longer than _PERIOD, it means the thermistor temperature
cannot catch up with the target, so something *may be* wrong. Then, to
be on the safe side, the system will he halt.
Bear in mind the count down will just start AFTER the first time the
thermistor temperature is over the target, so you will have no problem
if your extruder heater takes 2 minutes to hit the target on heating.
11 years ago
d86c3cf43c
Changed the type of variable to bool, the name to "cancel_heatup", flags implementation and added this fix to M190 gcode too.
11 years ago
f0cab611db
optimised some math-code
11 years ago
269a068032
Fix lcd itostr3() to handle negative numbers
11 years ago
fae7d08698
fixed wrong compiler-option
11 years ago
512f2a3136
restore Branch from Backup
...
sorry for that
11 years ago
cd3220d055
Inverted state logic for forced_heating_stop variable
11 years ago
86b4b805d2
Fixed stop print LCD function on M104
11 years ago
6e6e4e2143
Added thermistor table for the 500C thermistor shipped with the Pico hot end.
11 years ago
9d11b70436
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
0de826160e
M30 response is missing linefeed, "ok" therefore not on own line
...
This leads to the command not being acknowledged properly
by the firmware, leading to consecutive issues in host software
waiting for an acknowledgement.
11 years ago
3c927901a4
Implementation of FW extruder change retract
...
FW retraction is extended onto swap retraction invoked by 'G10 S1'.
Bookkeeping of the retract state of all extruders allows for having one
extruder fw standard retracted while another extruder is swap retracted.
An LCD menu item for the swap retract and recover length was added.
11 years ago
8a32c5395b
renaming the disable inactive extruder feature
11 years ago
29e7639933
Add switch unused feeder(s) off
...
Having the non-active feeder motors powered on all the time is not
necessary. A feature to deactivate the unused feeder motors has been
implemented. The feature is enabled on default but can be switched off
in the configuration.
11 years ago
07c0eeee99
Fixed a comment in the planner
11 years ago
09b84faa00
Configuration.h, pins.h: Add MOTHERBOARD 84 for Teensy++2.0
11 years ago
efb6d61413
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
38192cb5f3
Add M112 description to Marlin_main
11 years ago
aed5ec008a
Merge pull request #851 from DanNixon/estop
...
Implemented M112
11 years ago
cfb98ef682
More coverity fixes
11 years ago
92e14298b0
Fixes typo for lcd backlighting on I2C PCF8575
...
When using LCD_I2C_TYPE_PCF8575T (like Sainsmart I2C), the backlight
won't come on; the incorrect ifdef blocks the evocation of the backlight
functions.
11 years ago
9db9842aea
Fixed error found by the free coverity tool ( https://scan.coverity.com/ )
...
===================================================
Hi,
Please find the latest report on new defect(s) introduced to ErikZalm/Marlin found with Coverity Scan.
Defect(s) Reported-by: Coverity Scan
Showing 15 of 15 defect(s)
** CID 59629: Unchecked return value (CHECKED_RETURN)
/Marlin_main.cpp: 2154 in process_commands()()
** CID 59630: Operands don't affect result (CONSTANT_EXPRESSION_RESULT)
/Applications/Arduino.app/Contents/Resources/Java/hardware/arduino/cores/arduino/Tone.cpp: 319 in tone(unsigned char, unsigned int, unsigned long)()
** CID 59631: Missing break in switch (MISSING_BREAK)
/Marlin_main.cpp: 1187 in process_commands()()
** CID 59632: Missing break in switch (MISSING_BREAK)
/Marlin_main.cpp: 1193 in process_commands()()
** CID 59633: Out-of-bounds write (OVERRUN)
/temperature.cpp: 914 in disable_heater()()
** CID 59634: Out-of-bounds write (OVERRUN)
/temperature.cpp: 913 in disable_heater()()
** CID 59635: Out-of-bounds read (OVERRUN)
/temperature.cpp: 626 in analog2temp(int, unsigned char)()
** CID 59636: Out-of-bounds read (OVERRUN)
/temperature.cpp: 620 in analog2temp(int, unsigned char)()
** CID 59637: Out-of-bounds write (OVERRUN)
/temperature.cpp: 202 in PID_autotune(float, int, int)()
** CID 59638: Out-of-bounds read (OVERRUN)
/temperature.cpp: 214 in PID_autotune(float, int, int)()
** CID 59639: Out-of-bounds write (OVERRUN)
/Marlin_main.cpp: 2278 in process_commands()()
** CID 59640: Out-of-bounds read (OVERRUN)
/Marlin_main.cpp: 1802 in process_commands()()
** CID 59641: Uninitialized scalar field (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 51 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
** CID 59642: Uninitialized scalar field (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 45 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
** CID 59643: Uninitialized scalar field (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 32 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
________________________________________________________________________________________________________
*** CID 59629: Unchecked return value (CHECKED_RETURN)
/Marlin_main.cpp: 2154 in process_commands()()
2148 }
2149 #endif
2150 }
2151 }
2152 break;
2153 case 85: // M85
CID 59629: Unchecked return value (CHECKED_RETURN)
Calling "code_seen" without checking return value (as is done elsewhere 66 out of 67 times).
2154 code_seen('S');
2155 max_inactive_time = code_value() * 1000;
2156 break;
2157 case 92: // M92
2158 for(int8_t i=0; i < NUM_AXIS; i++)
2159 {
________________________________________________________________________________________________________
*** CID 59630: Operands don't affect result (CONSTANT_EXPRESSION_RESULT)
/Applications/Arduino.app/Contents/Resources/Java/hardware/arduino/cores/arduino/Tone.cpp: 319 in tone(unsigned char, unsigned int, unsigned long)()
313 else
314 {
315 // two choices for the 16 bit timers: ck/1 or ck/64
316 ocr = F_CPU / frequency / 2 - 1;
317
318 prescalarbits = 0b001;
CID 59630: Operands don't affect result (CONSTANT_EXPRESSION_RESULT)
"ocr > 65535U" is always false regardless of the values of its operands. This occurs as the logical operand of if.
319 if (ocr > 0xffff)
320 {
321 ocr = F_CPU / frequency / 2 / 64 - 1;
322 prescalarbits = 0b011;
323 }
324
________________________________________________________________________________________________________
*** CID 59631: Missing break in switch (MISSING_BREAK)
/Marlin_main.cpp: 1187 in process_commands()()
1181 case 2: // G2 - CW ARC
1182 if(Stopped == false) {
1183 get_arc_coordinates();
1184 prepare_arc_move(true);
1185 return;
1186 }
CID 59631: Missing break in switch (MISSING_BREAK)
The above case falls through to this one.
1187 case 3: // G3 - CCW ARC
1188 if(Stopped == false) {
1189 get_arc_coordinates();
1190 prepare_arc_move(false);
1191 return;
1192 }
________________________________________________________________________________________________________
*** CID 59632: Missing break in switch (MISSING_BREAK)
/Marlin_main.cpp: 1193 in process_commands()()
1187 case 3: // G3 - CCW ARC
1188 if(Stopped == false) {
1189 get_arc_coordinates();
1190 prepare_arc_move(false);
1191 return;
1192 }
CID 59632: Missing break in switch (MISSING_BREAK)
The above case falls through to this one.
1193 case 4: // G4 dwell
1194 LCD_MESSAGEPGM(MSG_DWELL);
1195 codenum = 0;
1196 if(code_seen('P')) codenum = code_value(); // milliseconds to wait
1197 if(code_seen('S')) codenum = code_value() * 1000; // seconds to wait
1198
________________________________________________________________________________________________________
*** CID 59633: Out-of-bounds write (OVERRUN)
/temperature.cpp: 914 in disable_heater()()
908 WRITE(HEATER_0_PIN,LOW);
909 #endif
910 #endif
911
912 #if defined(TEMP_1_PIN) && TEMP_1_PIN > -1
913 target_temperature[1]=0;
CID 59633: Out-of-bounds write (OVERRUN)
Overrunning array "soft_pwm" of 1 bytes at byte offset 1 using index "1".
914 soft_pwm[1]=0;
915 #if defined(HEATER_1_PIN) && HEATER_1_PIN > -1
916 WRITE(HEATER_1_PIN,LOW);
917 #endif
918 #endif
919
________________________________________________________________________________________________________
*** CID 59634: Out-of-bounds write (OVERRUN)
/temperature.cpp: 913 in disable_heater()()
907 #if defined(HEATER_0_PIN) && HEATER_0_PIN > -1
908 WRITE(HEATER_0_PIN,LOW);
909 #endif
910 #endif
911
912 #if defined(TEMP_1_PIN) && TEMP_1_PIN > -1
CID 59634: Out-of-bounds write (OVERRUN)
Overrunning array "target_temperature" of 1 2-byte elements at element index 1 (byte offset 2) using index "1".
913 target_temperature[1]=0;
914 soft_pwm[1]=0;
915 #if defined(HEATER_1_PIN) && HEATER_1_PIN > -1
916 WRITE(HEATER_1_PIN,LOW);
917 #endif
918 #endif
________________________________________________________________________________________________________
*** CID 59635: Out-of-bounds read (OVERRUN)
/temperature.cpp: 626 in analog2temp(int, unsigned char)()
620 if(heater_ttbl_map[e] != NULL)
621 {
622 float celsius = 0;
623 uint8_t i;
624 short (*tt)[][2] = (short (*)[][2])(heater_ttbl_map[e]);
625
CID 59635: Out-of-bounds read (OVERRUN)
Overrunning array "heater_ttbllen_map" of 1 bytes at byte offset 1 using index "e" (which evaluates to 1).
626 for (i=1; i<heater_ttbllen_map[e]; i++)
627 {
628 if (PGM_RD_W((*tt)[i][0]) > raw)
629 {
630 celsius = PGM_RD_W((*tt)[i-1][1]) +
631 (raw - PGM_RD_W((*tt)[i-1][0])) *
________________________________________________________________________________________________________
*** CID 59636: Out-of-bounds read (OVERRUN)
/temperature.cpp: 620 in analog2temp(int, unsigned char)()
614 if (e == 0)
615 {
616 return 0.25 * raw;
617 }
618 #endif
619
CID 59636: Out-of-bounds read (OVERRUN)
Overrunning array "heater_ttbl_map" of 1 2-byte elements at element index 1 (byte offset 2) using index "e" (which evaluates to 1).
620 if(heater_ttbl_map[e] != NULL)
621 {
622 float celsius = 0;
623 uint8_t i;
624 short (*tt)[][2] = (short (*)[][2])(heater_ttbl_map[e]);
625
________________________________________________________________________________________________________
*** CID 59637: Out-of-bounds write (OVERRUN)
/temperature.cpp: 202 in PID_autotune(float, int, int)()
196 {
197 soft_pwm_bed = (MAX_BED_POWER)/2;
198 bias = d = (MAX_BED_POWER)/2;
199 }
200 else
201 {
CID 59637: Out-of-bounds write (OVERRUN)
Overrunning array "soft_pwm" of 1 bytes at byte offset 1 using index "extruder" (which evaluates to 1).
202 soft_pwm[extruder] = (PID_MAX)/2;
203 bias = d = (PID_MAX)/2;
204 }
205
206
207
________________________________________________________________________________________________________
*** CID 59638: Out-of-bounds read (OVERRUN)
/temperature.cpp: 214 in PID_autotune(float, int, int)()
208
209 for(;;) {
210
211 if(temp_meas_ready == true) { // temp sample ready
212 updateTemperaturesFromRawValues();
213
CID 59638: Out-of-bounds read (OVERRUN)
Overrunning array "current_temperature" of 1 4-byte elements at element index 1 (byte offset 4) using index "extruder" (which evaluates to 1).
214 input = (extruder<0)?current_temperature_bed:current_temperature[extruder];
215
216 max=max(max,input);
217 min=min(min,input);
218 if(heating == true && input > temp) {
219 if(millis() - t2 > 5000) {
________________________________________________________________________________________________________
*** CID 59639: Out-of-bounds write (OVERRUN)
/Marlin_main.cpp: 2278 in process_commands()()
2272 tmp_extruder = code_value();
2273 if(tmp_extruder >= EXTRUDERS) {
2274 SERIAL_ECHO_START;
2275 SERIAL_ECHO(MSG_M200_INVALID_EXTRUDER);
2276 }
2277 }
CID 59639: Out-of-bounds write (OVERRUN)
Overrunning array "volumetric_multiplier" of 1 4-byte elements at element index 1 (byte offset 4) using index "tmp_extruder" (which evaluates to 1).
2278 volumetric_multiplier[tmp_extruder] = 1 / area;
2279 }
2280 break;
2281 case 201: // M201
2282 for(int8_t i=0; i < NUM_AXIS; i++)
2283 {
________________________________________________________________________________________________________
*** CID 59640: Out-of-bounds read (OVERRUN)
/Marlin_main.cpp: 1802 in process_commands()()
1796 int pin_status = code_value();
1797 int pin_number = LED_PIN;
1798 if (code_seen('P') && pin_status >= 0 && pin_status <= 255)
1799 pin_number = code_value();
1800 for(int8_t i = 0; i < (int8_t)sizeof(sensitive_pins); i++)
1801 {
CID 59640: Out-of-bounds read (OVERRUN)
Overrunning array "sensitive_pins" of 28 2-byte elements at element index 55 (byte offset 110) using index "i" (which evaluates to 55).
1802 if (sensitive_pins[i] == pin_number)
1803 {
1804 pin_number = -1;
1805 break;
1806 }
1807 }
________________________________________________________________________________________________________
*** CID 59641: Uninitialized scalar field (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 51 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
45 }
46
47 LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t enable,
48 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3)
49 {
50 init(1, rs, 255, enable, d0, d1, d2, d3, 0, 0, 0, 0);
CID 59641: Uninitialized scalar field (UNINIT_CTOR)
Non-static class member "_initialized" is not initialized in this constructor nor in any functions that it calls.
51 }
52
53 void LiquidCrystal::init(uint8_t fourbitmode, uint8_t rs, uint8_t rw, uint8_t enable,
54 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
55 uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7)
56 {
________________________________________________________________________________________________________
*** CID 59642: Uninitialized scalar field (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 45 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
39 }
40
41 LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t rw, uint8_t enable,
42 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3)
43 {
44 init(1, rs, rw, enable, d0, d1, d2, d3, 0, 0, 0, 0);
CID 59642: Uninitialized scalar field (UNINIT_CTOR)
Non-static class member "_initialized" is not initialized in this constructor nor in any functions that it calls.
45 }
46
47 LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t enable,
48 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3)
49 {
50 init(1, rs, 255, enable, d0, d1, d2, d3, 0, 0, 0, 0);
________________________________________________________________________________________________________
*** CID 59643: Uninitialized scalar field (UNINIT_CTOR)
/Applications/Arduino.app/Contents/Resources/Java/libraries/LiquidCrystal/LiquidCrystal.cpp: 32 in LiquidCrystal::LiquidCrystal(unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char, unsigned char)()
26
27 LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t rw, uint8_t enable,
28 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
29 uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7)
30 {
31 init(0, rs, rw, enable, d0, d1, d2, d3, d4, d5, d6, d7);
CID 59643: Uninitialized scalar field (UNINIT_CTOR)
Non-static class member "_initialized" is not initialized in this constructor nor in any functions that it calls.
32 }
33
34 LiquidCrystal::LiquidCrystal(uint8_t rs, uint8_t enable,
35 uint8_t d0, uint8_t d1, uint8_t d2, uint8_t d3,
36 uint8_t d4, uint8_t d5, uint8_t d6, uint8_t d7)
37 {
________________________________________________________________________________________________________
To view the defects in Coverity Scan visit, http://scan.coverity.com/projects/2224?tab=overview
11 years ago
e541323741
Merge https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
1c9a70cee9
Support for Gen3 Monolithic electronics
...
Techzone Monotronics support, ignoring the tip manager and using fan connector as on Sprinter FW
TODO: Add support for tipmanager
11 years ago
2acd3792fc
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
11 years ago
8b4c4aa5c3
Add feature to check&retry CRC read errors on SD.
11 years ago
ce76843dc3
Merge pull request #897 from Makible/5DPrint_D8_Board_Support
...
5DPrint D8 Controller Board Support
11 years ago
ad5c8cbba9
Add safety limit for hot bed power in example configuration
11 years ago
6460709d92
Fix bug in PID Autotune report
11 years ago
105bebb466
Fix for pin mapping for SDSS pin and Fan pin, so Arduino library can be used
11 years ago
97ead2eccb
Fix for microstepping pin mapping, not using Teensy pin mapping, but Arduino's default pin mapping so Arduino library can be used
11 years ago
d85411f13a
Revert "Fix for stepper microstepping"
...
This reverts commit eea3ba5588
11 years ago
7c7f2d094e
Revert "Fix for reading microstepping resolution"
...
This reverts commit 2715f6ddbf
11 years ago
e2d703377a
Enable EEPROM by default for 5DPrint D8 Controller Board in example configuration
11 years ago
2715f6ddbf
Fix for reading microstepping resolution
11 years ago
39e9b133f3
Add example configuration for Makibox printer, which uses the 5DPrint D8 Driver Board
11 years ago
da6b536182
Add 5DPrint D8 Driver Board info and temperature table for Makibox hot bed
11 years ago
3a8e36f19e
Add Digipot config for 5DPrint D8 Driver Board
11 years ago
eea3ba5588
Fix for stepper microstepping
11 years ago
1cbcbb0971
Add makibox machine information
11 years ago
2fa514e88a
Add port for 5DPrint D8 Driver board
11 years ago
b9126ab497
Merge pull request #894 from MyMakibox/Marlin_v1
...
Update Marlin_main.cpp
11 years ago
21ec6b88c3
Update Marlin_main.cpp
...
Added description of autotemp flags to M109
11 years ago
e4dc80d3d3
Update Configuration_adv.h
...
Corrected error in AUTOTEMP instructions
11 years ago
6adbdf42e0
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
27d544ac25
Speed up QUICK_HOME feedrate for diagonal move
...
Speed up the diagonal move while still keeping each individual axis at
or below its homing feedrate.
11 years ago
013793bbe9
Merge pull request #878 from koldoartola/Marlin_v1
...
Added new language (Basque-Euskera)
11 years ago
e5b70237c7
Added new language (Basque-Euskera)
...
Added:
* new language (Basque-Euskera)
* some minor corrections for Spanish
* added 2 new constants for every language (required for a minor change
I am preparing to ultralcd.cpp)
11 years ago
ed6f4a71c5
fix wrong temptable index
11 years ago
3161740df9
This table is made for thermistor 3950 (can be found on ebay for cheap)
...
it's caracteristics are :
R25℃ ;100KΩ±1%
B Value(R25/50℃)：3990K 1%
Dissipation Factor(mW/℃)：1.1~1.6 In still Air
Thermal Time Constant(S)：10~17 In Still Air
Operating temperature range： (-50~+260°C)
Dimension： 1.8mm Dia X4.1mm
Lead Length ：30mm
This table was found on the following blogs:
http://cae2100.wordpress.com/2014/03/08/beta3950-thermistor-table-for-marlin/
and
http://microfabricator.com/articles/view/id/531ad7e59aad9d3131000000/beta-3950-thermistor-table-for-marlin
11 years ago
086ff1644f
Merge pull request #852 from pixatintes/patch-1
...
Update language.h
11 years ago
3ffc9651b1
Merge pull request #845 from DerSchultze/Sanguinololu-servo
...
Added servo pin assignments to Sanguinololu
11 years ago
357b87b498
Merge pull request #826 from paciotti/patch-1
...
Configuration_adv.h
11 years ago
95ad6ec9a1
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
27a7cf9fcf
use existing strings
11 years ago
d3f305332a
Allowable range now includes default value
11 years ago
b0aeac117f
Adjustable Z probe offset, via custom M-code
11 years ago
73b380d8d2
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
c23376f2e7
Merge pull request #837 from whosawhatsis/fwretract
...
FWRETRACT in mm/s
11 years ago
dfb98101e4
Change CONTROLLERFAN_PIN for board 35 to -1, as it would conflict with board's 33 extruder pin, causing burnout (it's the same board, just different number of fans/extruders, therefore should be pin-compatible)
11 years ago
f1501317ca
Merge pull request #860 from drf5n/therm3950
...
thermistortables.h: Add comments that table 60 uses beta=3950.
11 years ago
9a5d23d96f
Merge pull request #866 from sakunamary/Marlin_v1
...
fix bug for dual extruders not working
11 years ago
303ee67896
Merge pull request #864 from whosawhatsis/M200
...
fix bug in M200 with multiple extruders
11 years ago
8759508319
fix bug for dual extruders not working
...
some guy find that marlin not working good for dual extruders delta .
when type T0 or T1 to active extruder and E0 or E1 move causing XYZ
motion . so i locales the bugs and fix it , I have dry run the fix.
11 years ago
a65564eef6
fix bug in M200 with multiple extruders
11 years ago
aeaf9b9312
fix bug in M200 with multiple extruders
11 years ago
89f78b0b80
Allow use of either SD Card slot when LCD Panel is configured.
...
Preference is for Controller SD slot before LCD Panel slot when both are occupied.
11 years ago
b0093a1513
thermistortables.h: Add comments that table 60 uses beta=3950.
11 years ago
a3530d1141
Update language.h
...
Updated to latest version.
11 years ago
990e770e15
Update language.h
...
Added catalan language
11 years ago
f643f4d674
Test and refactor
11 years ago
bbe8fbe13d
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
c8cdd1fc6f
Bugfixes for language option 6 (russian)
11 years ago
7395dafc1e
semantic changes in language.h
11 years ago
fad2a60ce6
Corrections for preheat extension in language.h
11 years ago
eecda434fb
Sanguinololu servo pins set default disabled
11 years ago
944ced87c5
Extended Preheat options
...
Preheat LCD menus base on code by D-Base
11 years ago
06709ad60e
Added servo pin assignments to Sanguinololu
11 years ago
3906f27c46
Individual extruder flow rate
...
Extension of M221, Tune menu
11 years ago
a38c90ee84
Added estop handling
11 years ago
a00cec8b71
Merge pull request #833 from mattsch/optional_feedrate_multiplier
...
Add support for disabling encoder control for feedrate multiplier
11 years ago
af8be9013b
Merge branch 'lcd_detected' of https://github.com/whosawhatsis/Marlin into Marlin_v1
11 years ago
0ddee3c7db
Prevent SD card insertion from causing a hang when using LiquidTWI2 device detection
11 years ago
272072fa20
Added M112
11 years ago
aab61e63c3
FWRETRACT in mm/s
...
Firmware retraction now stores the retract and recover speeds in mm/s
instead of mm/min. This makes it match the units of the maximum
feedrate, and fixes problems with modifying the value via LCD control
panel. From gcode, the values are still taken in mm/min to match the
units of G1 and similar, and they are converted to mm/s before they are
stored.
I also lowered the default retract feedrate to make it less likely to
cause problems for geared extruders when the user hasn’t bothered to
set a reasonable maximum feedrate, though users should be setting both
of these values to suit their hardware.
11 years ago
6cd85e6008
Add support for disabling encoder control for feedrate multiplier
...
Signed-off-by: Matthew Schick <matthew.schick@gmail.com>
11 years ago
09af1b90b8
Added CHDK support
...
Added CHDK support to take pictures instead of doing an IR command, see more about how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
11 years ago
765b2da3d4
Added CHDK support
...
Added so M240 can be used to trigger CHDK instead of sending an IR signal, see more about CHDK here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
11 years ago
881e348eed
Update Configuration_adv.h
...
Increase Z_HOME_RETRACT_MM to 2mm default to avoid end stop not switching during retract.
11 years ago
5a332df47e
Merge https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
15d1b8d719
Fixed finnish translation
...
- Fixed Few finnish transalations
- Removed duplicate contrast define
11 years ago
7325d7102e
Activate LiquidTWI2 device detection and space-pad LCD status line.
11 years ago
7f76a0e064
Merge pull request #813 from drf5n/PID_DEBUG
...
temperature.cpp: Fix PID_DEBUG compile error.
11 years ago
fcd8524b6e
Only increase EEPROM version for DELTA printers.
11 years ago
8ea5665ee2
Merge remote-tracking branch 'origin/Marlin_v1' into add/M665-set-delta-configuration
...
Conflicts:
Marlin/Marlin_main.cpp
11 years ago
8c4377dd63
temperature.cpp: Fix PID_DEBUG compile error.
11 years ago
fde8c2c310
Merge pull request #807 from Cylindric3D/typofixes_upstream5
...
Various typo fixes #5 - only in comments, no code changes.
11 years ago
fdce91192e
Various typo fixes - only in comments, no code changes.
11 years ago
d819c55395
Various typo fixes - only in comments, no code changes.
11 years ago
fd4542f33a
Merge pull request #805 from whosawhatsis/M200
...
autretract fix
11 years ago
e8291ed728
Merge pull request #802 from Makers-Tool-Works/Marlin_v1
...
Clarify which PID values to enter
11 years ago
465b654d24
Merge pull request #797 from Cylindric3D/update_menu_plan
...
Update menu plan
11 years ago
88506a80c3
Merge pull request #789 from smiler/Marlin_v1
...
Fixed typo.
11 years ago
b514d3c87f
Merge pull request #781 from Cylindric3D/typofixes_upstream
...
Various typo fixes #3 - only in comments, no code changes.
11 years ago
77df0d689a
autretract fix
...
I made these changes previously, but I can’t find the commit now. This
reapplies the changes to get auto retract working again.
Conflicts:
Marlin/Configuration_adv.h
Marlin/Marlin_main.cpp
11 years ago
cc5f1d475c
Merge pull request #772 from ellensp/Marlin_v1
...
Updated gen3+ board pins names to current convention
11 years ago
91759dede6
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into typofixes_upstream
11 years ago
557217fc05
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into update_menu_plan
11 years ago
aee63afccd
Clarify which PID values to enter
...
Users can be confused as to which values to enter after a PID tune. Updating the message to help clarity it.
New message: "PID Autotune finished! Put the last Kp, Ki and Kd constants from above into Configuration.h"
Old message: "PID Autotune finished! Put the Kp, Ki and Kd constants into Configuration.h"
11 years ago
99f6326544
Remove unnecessary dependency on time.h from qr_solve.cpp
...
Fixed compiler errors on Ubuntu using arduino-core
11 years ago
ea669cb504
Fix some extra and some missing tabs, to make the file consistent.
11 years ago
b46a1b6360
Update the menu plan document with the current menu as per ultralcd.cpp.
11 years ago
3cc7626d1f
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into update_menu_plan
11 years ago
174b8d99d5
Simplify 3-point probing using new code only
11 years ago
3b718b816c
better documentation
11 years ago
34fd59c370
ABL at any points
11 years ago
541155ea87
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into typofixes_upstream
11 years ago
9fa328e5c8
Merge pull request #793 from MissionSt/use_axis_enums
...
Use constants instead of numeric literals
11 years ago
f308a8af91
update comment
11 years ago
357e31270a
Prevent G29 without first homing in X and Y
...
If position is unknown, then G29 can be dangerous.
11 years ago
d2d7d186b5
Use descriptive constants, more
11 years ago
2ccdf4f36d
Use descriptive constants instead of numeric literals
11 years ago
c00383f286
Fixed typo.
11 years ago
60f72a78a9
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into typofixes_upstream
11 years ago
abba7a0003
Merge pull request #782 from marcovannoord/Marlin_v1
...
Added dutch to language.h
11 years ago
b868d668fa
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into typofixes_upstream
11 years ago
8212d8d543
Revert "Fixed small typo that would prevent compiling"
...
This reverts commit 51ae4881ab
11 years ago
46bae30573
Merge pull request #776 from whosawhatsis/fwretract
...
Fwretract fixes, cleanup
11 years ago
51ae4881ab
Fixed small typo that would prevent compiling
11 years ago
498d76fd79
Fixed some messages where the text shown on the screen was more than 17 characters
11 years ago
af9395ac2e
Add M605 to dynamically set delta configuration
...
Save above configs in eeprom
fix docs in createTemperatureLookupMarlin.py
add missing azteegX3pro digipot settings in delta example config
11 years ago
fd42f0d226
Merge pull request #783 from MissionSt/fix/syntax-error
...
Fix compile error
11 years ago
96217bf36a
Merge pull request #777 from PxT/M114
...
Add whitespace to M114 output
11 years ago
cf5c3b6610
Added dutch to language.h
11 years ago
d1c64b9dc4
Fix syntax error introduced in 477b6fa1d
11 years ago
5d50819791
Various typo fixes - only in comments, no code changes.
11 years ago
3f455889d0
Merge pull request #769 from Cylindric3D/typofixes_1
...
Various typo fixes - only in comments, no code changes.
11 years ago
4ddedb3b27
Merge pull request #780 from Cylindric3D/typofixes_2
...
Various typo fixes #2 - only in comments, no code changes.
11 years ago
d4ba23bc28
Merge pull request #770 from josefpavlik/Marlin_v1
...
Marlin v1
11 years ago
bbb424bd2f
Merge pull request #779 from MissionSt/makefile-fix-abl
...
Makefile fixes
11 years ago
8f0cee2a14
Various typo fixes - only in comments, no code changes.
11 years ago
08263ae66e
Merge branch 'Marlin_v1' into typofixes_1
11 years ago
5bd09d26e2
Makefile works with auto bed leveling
11 years ago
b45beeffd6
typo fix in Makefile
11 years ago
306588925d
Add whitespace to M114 output
11 years ago
c43838bb1e
disable auto retract by default
...
This should make it safe to enable FWRETRACT by default, with
autoretract (which should now be fixed) only enabled by M209. FWRETRACT
should probably now default to enabled (to make G10/G11 and M207-209
available, without changing functionality when they are not used), but
I’ll save that for another pull request/discussion.
11 years ago
99f0e44864
Move FWRETRACT defaults to configuration_adv.h
11 years ago
66e3869138
Fix autoretract
...
This takes the (now working) G10/G11 code and moves it to a function,
which is called by G10 and G11, and also called by G1 if autoretract is
enabled and a retract/recover move is detected.
11 years ago
2f2459c0db
Fix G10/G11 Z-lift
11 years ago
Scott Lahteine