da2a6f9a31
Accurate bed leveling: x loop inside y and zigzag motion
11 years ago
d29615dc0c
Z and Y dual stepper drivers error
...
if you try to enable Z_DUAL_STEPPER_DRIVERS the error "You cannot have dual drivers for both Y and Z" shows even if you don't have defined Y_DUAL_STEPPER_DRIVERS and don't let you compile the firmware
to solve this problem i change this line:
#ifdef Z_DUAL_STEPPER_DRIVERS && Y_DUAL_STEPPER_DRIVERS
to:
#if defined (Z_DUAL_STEPPER_DRIVERS) && defined (Y_DUAL_STEPPER_DRIVERS)
now the error only show if you define both Z_DUAL_STEPPER_DRIVERS and Y_DUAL_STEPPER_DRIVERS
11 years ago
5bde7fcb28
Minor code and comment polishing
11 years ago
20faff5935
Incorporate PS_DEFAULT_OFF for starting state on LCD menu entry
11 years ago
e5d3044801
Added posibility to set ENCODER_STEPS_PER_MENU_ITEM in Configuration.h like ENCODER_PULSES_PER_STEP as it depends on it for usability
11 years ago
b7eadb9f37
Made numbering of heat bed thermistor more logical as D8 is bed, D9 is Extruder 2 and D10 is Extruder 1, so T0 should be E1, T1 E1 and T2 bed to be sequential as MOSFET-Outputs
11 years ago
e8786bf110
Added support for Cheaptronic v1 electronic
11 years ago
cc2925b705
Implemented a least squares fit of the bed equation for auto bed leveling.
...
The code for the LSQ solver (qr_solve) is copyrighted by John Burkardt and released under LGPL here:
http://people.sc.fsu.edu/~%20jburkardt/c_src/qr_solve/qr_solve.html
(see qr_solve.cpp for further copyright information)
11 years ago
b64661070e
Fixed the plane vector equation to a simpler one (only dependent on the normal)
...
Removed the calculation of the inverse matrix since the rotation matrix is orthogonal, therefore inverted == transposed.
Much simpler and mathematically robust.
11 years ago
5c44f6c434
Bed Heater monitoring in Controller Fan
...
In some cases the Bed Heater FET heats up more then stepper drivers, so
this change add the bed monitoring to the controller fan. As soon as the
bed heater is turned on, the controller fan will run as well.
11 years ago
b33375d438
Z Axis Safe Homing when using Z Probe
...
Recommended for those who are using the Z Probe for Z Homing (as
Z-Endstop)
This feature has two changes:
1) Allow user to choose where the Z Probe will touch the bed when homing
all axis together (G28) by setting below defines:
Z_SAFE_HOMING_X_POINT
Z_SAFE_HOMING_Y_POINT
2) Prevents the user to perform Z Axis Homing when the Z Probe is
outsite bed.
11 years ago
35905ea4f9
Allow heaters to stay full On when PWM=127
...
In previous version, even with PWM = 127, the system turns the FET off
and then on in the next cycle. This bevavior may increase the FET heat
dissipation.
It was fixed keeping the FET always On when PWM=127.
11 years ago
a94e588765
Changed slow buttons behavior.
11 years ago
69af392554
Added HEATERS_PARALLEL (Request from reifsnyderb)
...
This allows a hot end with two heaters and a FET for each heater. This is useful if the FET is not capable of heating two heaters.
11 years ago
48a185d004
Fixed compile errors from bad commits.
11 years ago
24d1f480b6
Merge pull request #647 from shaggythesheep/newfeature-M226
...
Implement M226 - GCode Initiated Pause
11 years ago
95b41413e6
Merge pull request #641 from hugokernel/master
...
M80 - ATX Power On related modification
11 years ago
59b96e323e
Merge pull request #640 from fmalpartida/SAV-MkI
...
Added support for BT on AT90USB devices, corrected LCD bug, added new board and LCD
11 years ago
2433ee6fc8
Merge pull request #637 from justuswilhelm/Marlin_v1
...
Fix servo control for Melzi v2.0
11 years ago
3455a2bac2
Merge pull request #636 from PrintToPeer/Marlin_v1
...
Add UUID support to M115 responses.
11 years ago
dc887ef99b
Implement M226 - GCode Initiated Pause
...
Implemented M226 as described here:
http://reprap.org/wiki/G-code#M226:_Gcode_Initiated_Pause
Waits for pin to be become either HIGH, LOW or the inverse of what it
was before. Allows printing to pause until user interaction
11 years ago
c244eb860c
If you have a switch on suicide pin, this is useful if you want to
...
start another print with suicide feature after a print without
suicide...
11 years ago
7b556d2e96
Added BT support on AT90USB devices
...
Added AT90USB device BT connectivity support using second UART.
11 years ago
a5e8575829
Add UUID support to M115 responses.
11 years ago
cab84e0e5b
Add (correct) missing pin definitions for Y2
...
I tested this and it works.
11 years ago
5b3f60ea2e
Corrected LCD only error
...
If only an LCD is defined and no menu or keyboard defined, there is a
compilation error.
Added conditional compilation.
11 years ago
62d0b79023
Fix servo control for Melzi
11 years ago
b5a964fcc5
Initial SAV MkI (RepRap CloneWars board) integration.
...
Included support for BT dongle on AT90USB boards.
Added LCD Shift Register LCD control
Included support for RepRap Clone Wars project board (SAV MKI).
11 years ago
f941203172
PS_ON configurable boot state
...
Allows the user to select wheter or not the PSU should be turned on or
kept in standby when marlin boots
11 years ago
c79e3967b3
Make G11 not horribly broken
11 years ago
d69822ed51
Fix '#'
...
since it can occure in comments.
11 years ago
2fb2a0a119
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
39d88bcccb
preparation for hibernation
...
If a print is stopped, it would be nice in the future to write a file with the printer state, the filename of the print, and the position within the print.
this file could be read, to continue a previously stopped print.
not finished yet.
11 years ago
ab965376ff
Sub-file calls.
...
by overloading M32 it is now possible to execute gcode files from other gcode files, with a fixed recursion level.
This can be used e.g. for having a real start.g and end.g somewhere on the sd card, which are then called from the normal print file.
Another usecase would be to have macro-files for nozzle-change and layerchange.
I have not tested the speedwise performance. The testing was done with pronterface.
syntax:
normal call from sd card will open the new file and continue executing there.
M32 !/path/filename#
this however will call the new file and return to the caller file.
M32 P !/path/filename#
with the optional "S<position>" the file starting position can be set.
this is for continuing prints from a previous location.
11 years ago
b2cc27e5ea
Added a magic character for sd buffering.
...
if a '#' is read now the buffer will be emptied before reading ahead.
This is so one can execute files from within gcode files, without messing the buffer with preread characters from the caller file.
# can not occure in sd files imho, because it should only occure within checksums in ther serial communication.
Yes, thats a lame argument. If you have a better idea please tell me. It has to be a character that one can type
on a keyboard manually.
11 years ago
8a08cca0f2
Added temperature status less.
...
Hopefully fixed viky button handling without braking other boards
11 years ago
667d278f54
Revert "Fix for Viki display"
...
This reverts commit 314fd13c39
11 years ago
bf27e79e74
Small BlinkM fix
11 years ago
87e28c0599
Added ifdefs to blinkm
11 years ago
24c6b2ab35
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
6a803ba9c5
Merge pull request #590 from timkoster/Marlin_v1
...
Added BlinkM support over i2c
11 years ago
457d8a0acb
Fixed merge conflicts
11 years ago
6f85a8c7aa
Bed auto Leveling change: Raise Z before homing
...
- Added "Z_RAISE_BEFORE_HOMING" for raising Z the defined distance
before homing. This is useful to avoid Z-Probe collision when hotend is
near bed.
- Fixed the issue of Z not going bellow Z_PROBE_OFFSET when
"min_software_endstops" is true.
Now the Z_PROBE_OFFSET is not set in Z_MIN_POS, it is added after
homing.
11 years ago
dd3086d3f2
Show Temperature ADC values
...
If "SHOW_TEMP_ADC_VALUES" is defined in Configuration_adv.h, the M105
command will present, after tradicional temperatures, the ADC value read
from temp sensors. This is great for adjusting thermistor tables with
thermocouple.
From Pronterface you can see the ADC value and compare with a
thermocouple reading.. then you just need to create your own thermistor
table.
Since this merge doesnt change the original information, it doesnt mess
with PC software parsing (tested under Pronterface and Repetier-Host).
11 years ago
7fad13a1e2
Reverse SD card file name order.
...
This is _not_ automatically the cronological, since deleting a file will free
the filesystem descriptor for it, which then will be used by the next file copied on it.
Since this makes the auto0.g file very inaccessible, I put the option back, to have it in the prepare menu.
this should satisfy https://github.com/ErikZalm/Marlin/pull/373
as a reminder, auto0.g will be executed every time after a boot with sd card present and file present.
thereafter, if there is a file auto1.g this will be done. Thats IMHO the best place to put settings, and prepare heating.
I also execute again after each (now again via the prepare menu) before starting a new print/ after a failed one.
It for me 100% replaces any start.gcode form the slicers.
11 years ago
b832f5b9f6
added delta tower babystepping. Its untested, but hopefully florian horsch will be able to try.
...
also, removed some trouble for compilation with corexy.
I think that babystepping is only possible in z for a delta tower.
not sure if it would be usefull to step individual motors on a delta, i don't own one
11 years ago
c38b0855c8
I think that filament change is ready for the masses. I have tested very often with my ultimaker.
...
I strongly vote for it being a single gcode, because otherwise the triggering from the menu is terrible.
11 years ago
d147a057ac
Add the socalled "Babystepping" feature.
...
It is a realtime control over the head position via the LCD menu system that works _while_ printing.
Using it, one can e.g. tune the z-position in realtime, while printing the first layer.
Also, lost steps can be manually added/removed, but thats not the prime feature.
Stuff is placed into the Tune->Babystep *
It is not possible to have realtime control via gcode sending due to the buffering, so I did not include a gcode yet. However, it could be added, but it movements will not be realtime then.
Historically, a very similar thing was implemented for the "Kaamermaker" project, while Joris was babysitting his offspring, hence the name.
say goodby to fuddling around with the z-axis.
11 years ago
bca353cc12
Fixed duplicate define in fastio.h
11 years ago
253dfc4bc1
Bed Auto Leveling feature
...
Check the Readme for instruction how to enable and configure the feature
11 years ago
1bda6bf862
Merge pull request #609 from phq1910/patch-1
...
Update Configuration.h
11 years ago
c80aac1518
Merge pull request #610 from phq1910/patch-2
...
Update pins.h
11 years ago
314fd13c39
Fix for Viki display
11 years ago
4f7c6dfe35
Update pins.h
...
Include Pins cpu Sethi 3D
11 years ago
57173739a1
Update Configuration.h
...
Include CPU Sethi 3D
11 years ago
0dca49a7c0
Added Azteeg X3 board.
11 years ago
d8c2c810b4
Added info to the delta configuration files in the configuration.h file
11 years ago
9bc88f8bab
Placed optional ENCODER_PULSES_PER_STEP in the configuration.h file
11 years ago
3ca1ca6869
Fixed missing ENCODER_PULSES_PER_STEP
11 years ago
97b0da0c2e
Removed #ifndef BLINKM
11 years ago
61db046b32
Added #ifdef BLINKM around new code. Also refined BlinkM.h.
11 years ago
77df2ab0e7
Make Y_DUAL_STEPPER_DRIVERS disabled by default
11 years ago
ed1ab42186
Added Y_DUAL_STEPPER_DRIVERS
...
Enables two stepper drivers to be used for the Y axis (useful for
Shapeoko style machines)
Each Y driver can be stepped in either the same way or in opposite
directions, accounting for different hardware setups (leadscrew vs. belt
driven)
11 years ago
f4a59e4ce5
Revert "Added Y_DUAL_STEPPER_DRIVERS"
...
This reverts commit 7ee275b620
11 years ago
7ee275b620
Added Y_DUAL_STEPPER_DRIVERS
...
Enables two stepper drivers to be used for the Y axis (useful for
Shapeoko style machines)
Each Y driver can be stepped either the same way or in opposite
directions, accounting for different hardware setups (leadscrew vs. belt
driven)
11 years ago
6a1e980c6d
Merge pull request #600 from xoan/Encoder_Pulses_Per_Step
...
add ENCODER_PULSES_PER_STEP
11 years ago
20076a8bd3
Merge pull request #598 from GDV0/Marlin_v1
...
FIx compilation error when enabling SERVO_ENDSTOPS (#591 )
11 years ago
3626b5ad8b
Removed Delta from the default config file.
...
Changed EEPROM CHITCHAT behavior. M503 is always enabled.
11 years ago
bf7007d02f
add ENCODER_PULSES_PER_STEP
11 years ago
f17506c504
FIx compilation error when enabling SERVO_ENDSTOPS ( #591 )
11 years ago
acd8619809
Fan fix for Panelolu2+Sanguinololu.
11 years ago
595580556c
Fixed bug that makes ulticontroller knob backwards introduced Feb 28 2013 by Robert.
...
Bug introduced in version 6beb42cdf6839bef6d5d
11 years ago
88dfeefca3
Define BlinkM default disabled
11 years ago
5350faf2a2
Merge https://github.com/timkoster/MarlinBlinkM into Marlin_v1
11 years ago
7016cc9511
Added BlinkM support over i2c
11 years ago
3b315b3da0
Added BlinkM support over i2c
11 years ago
f26f26b7bd
Fix the example delta configuration as someone forgot to do it.
11 years ago
9aa2229077
add command M666 for adjusting delta printer endstop position
11 years ago
9547fb9dfb
Add duplication and auto-park mode for dual x-carriage support.
11 years ago
53614e5144
add pins for rambo lcd
11 years ago
b42d24e31e
add additional pins to avr2560 for rambo lcd
11 years ago
b0c8120fcc
Added feedrate setting in exemple config for manual moves from panel
11 years ago
a54fe2d73c
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1
...
Conflicts:
Marlin/Marlin_main.cpp
11 years ago
7ea63d08df
Merge pull request #565 from iXce/avrdudeconfpath
...
Detect OS in Makefile to use the correct avrdude.conf path
11 years ago
4187b637a5
Merge pull request #570 from hg42/separate-INVERTING-macros-for-MIN-and-MAX-endstops
...
separate INVERTING for MIN and MAX endstops (6 #defines instead of 3)
11 years ago
07e7de3600
Merge pull request #569 from hg42/convert-PROTOCOL-macros-from-statements-to-expressions
...
convert PROTOCOL macros from statements to (multiple, comma separated) expressions
11 years ago
c0c4c97db6
Detect OS in Makefile to use the correct avrdude.conf path
11 years ago
2ca983568d
separate INVERTING for MIN and MAX endstops (6 #defines instead of 3)
11 years ago
3700f688f5
convert PROTOCOL macros from statements to (multiple, comma separated) expressions
11 years ago
a504c88346
Fix a bug where the PID controllers D action kicks in hard as soon as the PID controller starts.
11 years ago
394ed08f88
Added feedrate setting for manual moves from panel
11 years ago
9bf1cf1b22
Pre-calculate diagonal rod length squared
11 years ago
4623e78ce0
Added Honeywell thermistor 135-104LAF-J01
11 years ago
d7f384f680
Skip SD menu refresh if nothing has changed
11 years ago
abc8320a68
Save LCD_CLICKED before it is cleared
...
The SD card menu was refreshing so slowly that the button interrupt was clearing LCD_CLICKED before the menu items could check it.
11 years ago
f4c3135c6d
Add Panelolu2 pins for RAMPS1.3
11 years ago
aae42c68f9
Update French translation in language.h
11 years ago
4d435c38a6
Add support of LiquidTWI2-based panels to Makefile
...
Use LIQUID_TWI2=1 as make argument to enable this support
11 years ago
6c42a3a339
Woops, fix logic
11 years ago
376d8af2c8
Report temperatures for all extruders
11 years ago
434b6a05c1
Merge pull request #552 from iXce/Marlin_v1
...
Report temperatures for all extruders in reply to M105
11 years ago
bdc2621119
Merge pull request #561 from Brendan-csel/Marlin_v1
...
Fix for Viki LCD issues printing from SD card
11 years ago
6965bd4e15
Merge pull request #560 from njprossi/Marlin_v1
...
Fixed move from panel for delta bot #557
11 years ago
a55b33e613
Merge pull request #559 from iXce/panelolupinsramps13
...
Add Panelolu2 pins for RAMPS1.3
11 years ago
8b34351537
Merge pull request #558 from iXce/frenchupdate
...
Update French translation in language.h
11 years ago
735e556724
Merge pull request #555 from iXce/liquidtwi2_makefile
...
Add support of LiquidTWI2-based panels to Makefile
11 years ago
d80aecda0a
Skip SD menu refresh if nothing has changed
11 years ago
be2dea1dc6
Save LCD_CLICKED before it is cleared
...
The SD card menu was refreshing so slowly that the button interrupt was clearing LCD_CLICKED before the menu items could check it.
11 years ago
55c287a69e
Fixed move from panel for delta bot #557
11 years ago
1902d339b0
Add Panelolu2 pins for RAMPS1.3
11 years ago
eb23a68e92
Update French translation in language.h
11 years ago
1561c6df51
Merge pull request #547 from wolfmanjm/delta-configuration
...
Setup Default configuration for Deltas if DELTA is defined
11 years ago
374bc99fa3
Add support of LiquidTWI2-based panels to Makefile
...
Use LIQUID_TWI2=1 as make argument to enable this support
11 years ago
ab624eac2a
revert COnfiguratiuon to the same as head
11 years ago
52f79ffeca
add an example default configuration for delta style bots
11 years ago
b9d7ccf1cd
Merge remote-tracking branch 'upstream/Marlin_v1' into delta-configuration
...
Conflicts:
Marlin/Marlin_main.cpp
11 years ago
d4d1540727
Use -fno-use-cxa-atexit to override gcc --enable-cxa_atexit
11 years ago
01ed99143c
Woops, fix logic
11 years ago
76841450c8
Only display poweron/poweroff if PS_ON_PIN > -1
11 years ago
44f327d738
Uniformly reindent language.h
11 years ago
326d2db025
Update language.h so that all languages compile
...
Some strings still need translation, but at least everything compiles.
11 years ago
2cb716f513
Run Marlin/language.h through dos2unix
11 years ago
34da3a0a3f
Merge github.com:ErikZalm/Marlin into Marlin_v1
...
Conflicts:
Marlin/language.h
11 years ago
18199ff960
Merge github.com:ErikZalm/Marlin into Marlin_v1
11 years ago
fb5334f428
Fixed compile error when QUICK_HOME is defined.
...
As well a couple of minor changes to handling of extruder offset for
dual x-carriage mode.
11 years ago
c3568398b5
Disable DUAL_X_CARRIAGE by default
11 years ago
39cd3dbdbe
Remove dual x-carriage functionality that could/should be implemented in slicer
...
Also added a couple of missed merge lines in homeaxis() from previous
commit.
11 years ago
fb20ceabce
enable soft endstops for delta
...
disable delta by default
11 years ago
d01ee7e7b5
fix zjerk being the same for delta as xy jerk
...
add more delta defaults
on delta make second home even slower
11 years ago
d7390e13d9
Support dual x-carriage printers
...
Dual x-carriage designs offer some substantial improvements for dual
extruder printing.
11 years ago
f3aa2a48e7
update max pos
11 years ago
460751503e
Added default configurations for deltas when DELTA is defined
11 years ago
9da94c247a
fixed bad lcd commit from makr3d
...
#elsif does not exist #elif is correct
12 years ago
59004023fd
Fixed typo
12 years ago
461dad6e05
Added : M32 - Select file and start SD print (Can be used when printing from SD card)
...
Untested
12 years ago
c4a2077951
M109 and M190 now wait when cooling down if R is used instead of S.
...
M109 S180 waits only when heating.
M109 R180 also waits when cooling.
12 years ago
8a2a3ef91d
Merge pull request #531 from iXce/Marlin_v1_lcd
...
Only clamp panel movements if software endstops are enabled
12 years ago
6397b3339c
restored configuration.h defaults
12 years ago
cdaaad3df1
Merge branch 'Marlin_v1' of https://github.com/makr3d/Marlin into makr3d-Marlin_v1
12 years ago
e3bdefd873
fixed missing #endif
12 years ago
a5be0c52c6
no message
12 years ago
e509cdbeb0
added contrast control function for gLCDs
12 years ago
99b7e926e7
added MaKr3d Melzi board
12 years ago
68be33b1fc
Update language.h
...
I update the spanish Messages, now this compile for spanish language.
12 years ago
acb3271c9a
Merge pull request #534 from xifle/Marlin_v1
...
Fixes compiler warning for feedrate deadzone
12 years ago
61fe430d4f
Should fix compiler warning for feedrate deadzone
12 years ago
fde17d5720
Fix for ugly code compilation errors in SERVO_ENDSTOP checks
12 years ago
aa65c20d1f
Only clamp panel movements if software endstops are enabled
12 years ago
ecf3ab5de4
Added thermistor 60 to configuration.h
12 years ago
2daa85918e
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
Marlin/Marlin_main.cpp
Marlin/language.h
Marlin/pins.h
Marlin/ultralcd.cpp
12 years ago
2015989f84
Added DISABLE_MIN_ENDSTOPS
12 years ago
648d45cfb2
Fix Pin Description Typo
...
Reverse 'Bed' and 'Fan' at the RAMPS 33 Description.
Signed-off-by: Christian Inci <chris.pcguy.inci@gmail.com>
12 years ago
171719f18c
Merge pull request #525 from lajos/ultralcd_pid
...
ultralcd.cpp compile errors when !defined(PIDTEMP)
12 years ago
b519af4f05
fixed another !defined(PIDTEMP) compile in ultralcd.cpp
12 years ago
7d03c52511
fixed compile error in ultralcd.cpp when PIDTEMP undefined
12 years ago
02dee80fa5
added Azteeg X1 motherboard
12 years ago
47dc70e3ec
Fix location of avrdude.conf
12 years ago
1d258903bb
Allow command line compilation when using BEEPER.
12 years ago
e34c9981ab
Delta disabled by default
12 years ago
26a441fc7d
More 3Drag controller patches.
12 years ago
ac975ed8c2
Merge branch 'deltabot' into Marlin_v1
12 years ago
caa848f943
fix homing for deltas
12 years ago
7ad12be763
Merge branch 'Marlin_v1' of https://github.com/codexmas/Marlin into codexmas-Marlin_v1
...
Conflicts:
Marlin/Configuration.h
README.md
12 years ago
408169aef4
Merge branch 'Marlin_v1' of https://github.com/BorisLandoni/Marlin into BorisLandoni-Marlin_v1
...
Conflicts:
Marlin/Configuration.h
Marlin/language.h
Marlin/pins.h
12 years ago
bd96d22bfb
Merge branch 'Marlin_v1' into thinkyhead
...
Conflicts:
Marlin/Configuration.h
Marlin/Configuration_adv.h
Marlin/Marlin.h
Marlin/Marlin_main.cpp
Marlin/Servo.cpp
Marlin/language.h
Marlin/pins.h
Marlin/planner.cpp
Marlin/ultralcd_implementation_hitachi_HD44780.h
README.md
12 years ago
73f21cd5d6
Spanish updated so far.
12 years ago
6f4a6e531c
Merge branch 'deltabot' into Marlin_v1
12 years ago
01edf22a10
Fix home_all_axis to make QUICK_HOME work with Repetier-Host which sends G28 X0 Y0 Z0 instead of G28. Thanks to Matt Schoenholz for reporting this issue.
12 years ago
ff6fa09ecf
Moved corexy implementation from stepper to planner
...
(Thanks iquizzle)
12 years ago
c8dcc7c208
Allow increasing the software PWM frequency.
12 years ago
8b0d82e9db
Removed "awaiting translation" for french
12 years ago
1e05d192ab
Make the beep tone less offensive
12 years ago
373f3ecab3
Merge branch 'deltabot' of https://github.com/jcrocholl/Marlin into deltabot
...
Conflicts:
Marlin/Configuration.h
Marlin/Marlin_main.cpp
Marlin/pins.h
12 years ago
f295712008
Trying to fix weird diff on ultralcd_implementation_hitachi_HD44780.h
12 years ago
69b02031ca
Fixed small error in lcd define statements.
12 years ago
6a81291c57
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
...
This should fix issues with pull request 467, I hope.
Conflicts:
Marlin/Configuration.h
Marlin/Marlin.pde
Marlin/ultralcd_implementation_hitachi_HD44780.h
12 years ago
c1cb5977ee
Update Configuration.h
12 years ago
8a5bd8a808
Update Configuration.h
12 years ago
c1d7cf939e
Update language.h
12 years ago
4c7d1436e9
Update pins.h
12 years ago
6588933c04
Update Configuration.h
12 years ago
5dabc95409
Apply all changes from latest Marlin_V1
...
Diffed and merged, preserving my updates
12 years ago
a733537ddd
Missed some variable declarations
...
Integrated fixes from henrikbrixandersen pull request #504
12 years ago
f4f30c9d64
Added servo actuated enstop coding to allow G28 command to engage and retract a servo to specified angles.
12 years ago
79374f0b93
Merge branch 'reisnyderb' of https://github.com/ErikZalm/Marlin into Marlin_v1
12 years ago
da05b3ba94
faster GLCD (ST7920 SW-SPI) implementation / fixes
...
- fixed long menu entries (>14 or >18 chars) caused overrun in dogm lcd
implementation
- fixed pin set problem when in interrupt
- much faster ST7920 SW-SPI implementation
- increased ST7920 framebuffer size for more speed
12 years ago
4b19c8552e
Fixing changed Configuration.h settings to be default values per ErikZalm Request.
12 years ago
971ec35135
Expanded M302 to allow setting the temp
12 years ago
5090c56651
More redundant temp sensor changes. (After testing and debugging by reifsnderb)
12 years ago
16b9239a26
Report temperatures for all extruders
12 years ago
a964b3cf3d
Merge pull request #495 from Gatulibu/Marlin_v1
...
Added support for Megatronics v2.0 and Minitronics v1.0
12 years ago
e8572c5239
Fix: Long menu entries (>14 or >18 chars) caused overrun in hitachi display implementation
12 years ago
7ee70c2248
Fix: removed wrong ; at end of define
12 years ago
b78fa6bb70
Added support for Megatronics v2.0 and Minitronics v1.0
...
merged from code downloaded from reprapworld.com
12 years ago
9be61cdc02
Added redundant temp sensor
12 years ago
7231a20dba
Put #ifdef around servo pins in pins.h. This allows the pins to be used for M42.
12 years ago
e2ff536b03
Fixed typo in Comment
12 years ago
40eb07bad4
Revert and extend previous change pin check change
...
Reviert previous change of #if BLAH_PIN > 0 to #if defined(BLAH_PIN) &&
BLAH_PIN > -1. Unfortunately some times pin 0 is used. For my sins I've
gone through and replaced all unsafe checks of #if BLAH_PIN > -1 with
the safe version.
12 years ago
bd33cf4a9f
fixed typo / added "const" to defines for newer gcc compatibility
12 years ago
567291e734
Merge pull request #485 from Banjer/Panelolu2_Melzi
...
Add Panelolu2 support for Melzi
12 years ago
8d80cbbf4c
fix broken LCD commit #dfa549f268 from buildrob - GLCD/DOGM implementation was ignored
12 years ago
98d0d48191
fixed merge
12 years ago
bbe67fca5a
soft tab correction
12 years ago
9eeb711c96
Merged from Upstream Master
12 years ago
424101110c
Add Panelolu2 support for Melzi
12 years ago
0d4a9444c4
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
12 years ago
86cce025f4
Added #ifdef NUM_SERVOS to servo.cpp
12 years ago
03141a5ef4
LCD: Added Deadzone at 100% Feedrate
...
This adds a deadzone at 100% Feedrate when changing it at the status
screen/main menu. Prevents from unwanted feedrate-changing when
navigating back to the main menu and makes it easier to return to 100%.
12 years ago
28ada096e2
Adding servo documentation
12 years ago
4121311b9d
Change to LCD status indicators
...
The I2C LCD status indicators now indicate when the hotends or bed are
turned on at all (rather than just when they are in their heating phase)
12 years ago
dfa549f268
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
12 years ago
64360164ad
Merge pull request #482 from codexmas/Marlin_v1
...
servosupport
12 years ago
86405cdd11
Merge pull request #479 from MStohn/thermocouple
...
BUGFIXES for temperature.cpp / add RUMBA thermocouple support
12 years ago
6c45c3f4e7
BariCUDA changes
12 years ago
96624f0f31
Forgot to include reference to Servo in makefile
12 years ago
dc59f07d24
First attempt at refactoring of original servo code. Only adding servo support as a start to keep things simple.
12 years ago
b668cb0516
Adding in clean copies of Servo library from Arduino 1.0.4
12 years ago
95dff34b73
fixed wrong compare for min temp check of heater 1 and heater 2
12 years ago
4cc6f9f6de
fixed wrong pin initialization when using temperature 2 pin input
12 years ago
61a48cc662
Add support for RUMBA thermocouple add on
12 years ago
9cc15876be
Add support for RUMBA thermocouple add on
12 years ago
c9cf2174dd
Merge pull request #474 from xifle/Marlin_v1
...
Fixed "Cooldown" Selection not reseting bed temp
12 years ago
bd2cd4903e
Added #ifdef BARICUDA around the BariCUDA changes
12 years ago
37f3199df3
fixed problems in planner with solenoids for BariCUDA when set to 0
12 years ago
fbd899a37d
Support for BariCUDA Paste Extruder derived from MakerBot Frostruder. Using Ultimachine RAMBo board. M126/M127 and M128/M129.
12 years ago
29bb8d7d4f
Fixed "Cooldown" Selection not reseting bed temp
...
- enquecommand with multiple lines "\n" doesn't work -> M140 S0 didn't
get processed. So I wrote a new func for the cooldown which uses
setTargetHotend. In addition this does return to status page after
selection.
- Added setWatch() to preheat-functions (Temperatur sanity check
would never have worked when preheating from the lcd panel)
12 years ago
015d0594b0
Optimize menu selection for Viki rotary encoder.
...
The Viki LCD rotary encoder uses a different number of steps per
rotation. This fixes the seeming "missed" steps when selecting a menu.
12 years ago
2739c26c4f
changes:
...
- changed the variables from keypad to reprapworld_keypad
- added a missing ifdef check
12 years ago
6fb9573157
added support for the reprapworld keypad
12 years ago
594193c908
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
12 years ago
1fa61c297e
Turning off Control Panel by Default and Updating the link to the LiquidCrystal_I2C library to avoid confusion.
12 years ago
b27a59f41e
Added support for Elefu RA Board and Elefu Control Panel
12 years ago
a65a26d6b4
If CORE_XY is in use X and Y Axis had to be activated at the same time
12 years ago
db2f157a22
Replace the <= to < in the Command M907, M350 and M351.
...
The for loop for Axis count over the Array.
Add a break after M907
12 years ago
a5cd582665
Support for 10 level deep SD folder hierarchy
12 years ago
fc4ab05157
Solved minor bug in controllerFan()
...
Extruder 2 was checked where extruder 1 should be checked.
12 years ago
0ef54f2f85
Make M303 silent when "S0" is sent
...
If S is left out perhaps it should be silent, but check the spec for
this M code.
12 years ago
a200521eab
Added CUSTOM_MENDEL_NAME option to Configuration.h and language.h
...
Also cosmetic comment changes and spelling corrections in printed
messages
12 years ago
1a397825f9
fix DEFAULT_AXIS_STEPS_PER_UNIT minor Z rounding error
12 years ago
289c02eda4
Remove unnecessary pin initialization in stepper.cpp
...
(duplicates initialization in Marlin_main.cpp)
12 years ago
d5ad7a0814
Rework change to incorporate CONTROLLERFAN
...
Also refactor extruder auto fan logic to simplify further and now only
check every 2.5 seconds
12 years ago
c3cdaceab3
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
12 years ago
1c127217df
Make DOGLCD merge neater.
12 years ago
7f57f28ccc
Add lcd_buzz function to ultralcd.h so that non-LCD code can make use of lcd's buzzer.
...
Argument order of lcd_buzz was set to mirror that on tone(). Change
default M300 frequency to something audible.
12 years ago
788d62bcc4
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Marlin.pde
Marlin/ultralcd.cpp
Marlin/ultralcd_implementation_hitachi_HD44780.h
12 years ago
d71f1e9bf6
Add (as an option) slower SD transfer mode
12 years ago
db5bb8546d
Merge pull request #452 from MStohn/Marlin_v1
...
128x64 RepRapDiscount Full Graphic Smart Controller support
12 years ago
4b2ece159b
Merge pull request #453 from brackendawson/Marlin_v1
...
Make Gen7 1.4+ heater temp sensort pins match silkscreen.
12 years ago
d5ee2a5a62
Make Gen7 1.4 heater pins match silkscreen
12 years ago
7ac6d7f78e
FIX: Speedup - no explicit display clear needed in u8glib
12 years ago
13596e8722
Added RepRapDiscount FULL GRAPHIC Smart Controller
12 years ago
3a6abe1d6e
Removed STB custom font hack from u8glib library and moved to marlin project
12 years ago
16afbf9bfa
FIX: adopted latest changes from hitachi implementation
12 years ago
34bca48b98
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
12 years ago
ac52dcc174
Updated the card menu and watch messages to make it more informative.
12 years ago
31bb3fb297
Fix: Build error when EEPROM_SETTINGS is defined and PIDTEMP is undefined
12 years ago
c80a78bb70
Lower the default max E feedrate a bit. With the stepper fix this is much to high.
12 years ago
5d5909fc25
Fix failure to compile with heated bed: remove call to non-existant scaleBedPID().
12 years ago
93f0463b21
Allow Edit menu to call fn after edit; Fix PID Ki and Kd display in menus; Actually use changed PID and Max Accel values
...
Add new 'callback' edit-menu types that call a function after the edit is done. Use this to display and edit Ki and Kd correctly (removing the scaling first and reapplying it after). Also use it to reset maximum stepwise acceleration rates, after updating mm/s^2 rates via menus. (Previously, changes did nothing to affect planner unless saved back to EEPROM, and the machine reset).
Add calls to updatePID() so that PID loop uses updated values whether set by gcode (it already did this), or by restoring defaults, or loading from EEPROM (it didn't do those last two). Similarly, update the maximum step/s^2 accel rates when the mm/s^2 values are changed - whether by menu edits, restore defaults, or EEPROM read.
Refactor the acceleration rate update logic, and the PID scaling logic, into new functions that can be called from wherever, including the callbacks.
Add menu items to allow the z jerk and e jerk to be viewed/edited in the Control->Motion menu, as per xy jerk.
Conflicts:
Marlin/language.h
12 years ago
4fa2260a59
Fixed cardreader.h to resolve issue #440 (Pull Request #425 missing file)
12 years ago
038d405254
Corrected #endif in language.h
12 years ago
443aaa30bf
Removed GIT fragments
...
Seems that there was something wrong while merging
12 years ago
7f622467fc
Merge pull request #425 from kefir-/m928_logging
...
M928 logging
12 years ago
86867928ac
Merge pull request #434 from DDRBoxman/Marlin_v1
...
Add support for M300: Play beep sound
12 years ago
9a38cad6f0
Merge pull request #430 from STB3/GLCD_128x64_dots
...
Final task of the 128x64dots GLCD implementation
12 years ago
7a5c474d91
Update Configuration.h
12 years ago
4e448b700a
Merged fetched files from Marlin_v1 branch
...
Pull requests: #414 #433 #432 #428
12 years ago
9f2862ce48
Merge pull request #414 from whosawhatsis/Marlin_v1
...
regenerated thermistor table 7
12 years ago
9fb8bd5685
Merge pull request #433 from whosawhatsis/bang-mode
...
Separate PID_MAX from BANG_MAX
12 years ago
0d075378d5
Add LARGE_FLASH define and enable it for some of the beefier boards
...
The LARGE_FLASH flag allows superfluous features to be excluded
on boards with less memory
12 years ago
9a1c90471f
Ignore unused beeper pins
12 years ago
1a0f889803
Add support for M300: Play beep sound
12 years ago
9322c408c6
Updated for LiquidTWI2 library version 1.2.3
...
The new version of the library means that PANELOLU no longer needs to be
defined in LiquidTWI.h (the library file can be used as is) and the new
version of the library also enables the buzzer on the Panucatt VIKI
panel.
12 years ago
fd5b7e0cec
Separate PID_MAX from BANG_MAX
...
This allows PID_FUNCTIONAL_RANGE to use a maximum duty cycle higher
than PID_MAX. This is useful for powerful heaters to heat quickly in
bang-bang mode, but use a lower duty cycle that is easier to stabilize
in PID mode.
12 years ago
e5a853a3d0
Added automated extruder fan function
12 years ago
72419f69a9
Added rumba
12 years ago
91bea43332
Added rumba pinout
12 years ago
d2b00fe486
Removed html and added rumba
...
Found some unwanted html at the bottom of the file which caused it to not be able to compile.
Also added rumba as machine.
12 years ago
6c66cae694
GLCD init screen cosmetics
12 years ago
f3e0e5184d
Add include selector between char. LCD and GLCD
12 years ago
5d3862f9d1
Modified u8glib logo on welcome screen
12 years ago
0b320f75e9
Removed debug code, add some comments
12 years ago
5f1cd70122
Add code to lcd_update() for GLCD
...
This code selects between the routines for the GLCD or the char.
display.
12 years ago
a49c09a776
Add variable for animated fan, add float conversion w/o sign
...
A new variable was introduced to allow fan animation on the GLCD.
Add additional float to string conversion routine without sign
character. This is used for the coordinates visualisation on the GLCD.
12 years ago
26d8863111
Add library selection between GLCD and char. LCD
12 years ago
4a141a694f
Marlin code for GLCD display
...
This contains the menues, status screen etc...
12 years ago
83c790a020
Add bitmap graphics for GLCD
...
1. Marlin welcome screen
2. Status screen symbols 3 Extruders, heated bed, animated fan logo 1
3. Status screen symbols 3 Extruders, heated bed, animated fan logo 2
12 years ago
233df9cca0
Add missing LF at the end of the file
12 years ago
bb0de75a92
Removed umwanted HTML code ath the end of the file
...
Sorry for that. This does not lead to compile errors. I removed the
unwanted code to make it clean.
12 years ago
7c47e7162d
Adding Maker's Tool Works heated bed thermistor
12 years ago
af78d0cbfa
Merge pull request #1 from illuminarti/Fix_E_Speed
...
Fix step rate bug (especially for retraction)
12 years ago
9a78f321a4
Add pins for Motherboard variant 64
...
These definition contain also the definition for the graphics LCD.
12 years ago
5de25ccd20
Add Motherboard variant 64 - STB V1.1
...
Definition for the graphic LCD are already in it, they will not harm the
configuration as they are only defined constants
12 years ago
d6ce63c49c
Merge pull request #411 from STB3/Marlin_w_STB_Board_support
...
Add STB board support to Marlin (next step towards graphic LCD implementation)
12 years ago
f036be7c4e
Clean up tab/whitespace from last commit
12 years ago
07e11c7cf5
Add command M928 to enable logging to file of received gcode commands
12 years ago
92782f9252
Merge pull request #1 from illuminarti/Fix_E_Speed
...
Fix step rate bug (especially for retraction)
12 years ago
6a61a3c0b4
missing comma in last commit
12 years ago
f0aee4101a
regenerated thermistor table 7
...
Generated with createTemperatureLookup.py. The old table crapped out at
270C, which was a problem for polycarbonate.
12 years ago
aba67e2449
No bed config for RAMPS
...
The motherboard 35 is a config without bed with this pins setting :
D8 Extruder
D9 Fan
D10 Controller Fan
12 years ago
6504e96165
Turn off power supply off-load
...
Disable the high current output and wait a little before to turn off,
because the interrupting capacity of the PSU is unknown.
Could be a function if needed by other.
12 years ago
86bf911139
Toggle menu for PSU from LCD pannel
...
From the prepare menu, accessible when is not printing, you have the
possibility to turn off the PSU when is on et vice versa.
From the host, you can turn off or turn on the PSU then the menu is
updated accordingly.
From the LCD message, the printer status is reported ready or off
respectively when the PSU is on or off.
12 years ago
7bad72359c
Support encoder click on PANELOLU2 being read through I2C
...
This change also handles the case where the pause/stop/restart button on
the VIKI is not used. Make LCD I2C buzz sound the same as the normal
buzz (300ms is too long for quick feedback).
12 years ago
1daf2f3256
Number of extruders is not an advanced configuration - it is a basic property.
12 years ago
f1263d3f88
Further reduce code by using precompiler logic
12 years ago
140e095c6e
Add pins for Motherboard variant 64
...
These definition contain also the definition for the graphics LCD.
12 years ago
b2c1c64fb1
Add Motherboard variant 64 - STB V1.1
...
Definition for the graphic LCD are already in it, they will not harm the
configuration as they are only defined constants
12 years ago
ceb5ee38af
Replaced corrupted language.h file on local PC with current from ErikZalm/Marlin
12 years ago
8efd4cfd73
fixed merge conflict
12 years ago
372e12f83f
Implement automatic extruder/cold-end fan control based on temperature
...
This change allows fan outputs to automatically turn on/off when the
associated nozzle temperature of an extruder is above/below a threshold
temperature.
Multiple extruders can be assigned to the same pin in which case the fan
will turn on when any selected extruder is above the threshold.
It also makes the M42 command compatible with the M106/M107 command.
The majority of the logic in this change will be evaluated by the
compiler at build time (i.e, low code space requirements).
12 years ago
6beb42cdf6
Attempt to address Bernhard's comments
...
Refactor configuration to try to make items clearer (what defines a
panel vs what is user changeable).
12 years ago
839bef6d5d
Fix Configuration.h file to not define LCDs be default.
...
Also fix compile time check in Marlin.pde
12 years ago
1292d735ba
Converge all I2C LCD branches (PANELOLU2, VIKI & PCF8575)
...
This includes refactoring the buttons code to remove a large amount of
non-pin dependent duplication from pins.h.
12 years ago
4eb81a69e6
Only compile the new extruder offset code if you have multiple extruders.
12 years ago
3e9cd334a4
Merge pull request #383 from dob71/jeff
...
Hotend offset handling for multi-extruder machines
12 years ago
67710df9f3
Made i2c mode wok with the hardware I am able to test (ywrobot / sainsmart i2c LCD 2004)
...
Removed incorrect LiquidCrystal_I2C Library
12 years ago
b6209c86dd
Added import of Wire Library to make I2C LCD support compilable
12 years ago
2b567d1df5
Added I2C port expander support to HD44780
12 years ago
06272f463d
Added Config variables for activating I2C LCDs and setting type and address
12 years ago
de3dec7215
Also show the tune menu when USB printing.
12 years ago
73d41c10b9
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into jeff
...
Conflicts:
Marlin/language.h
Marlin/thermistortables.h
12 years ago
63da4dc59a
Merge pull request #398 from DanieleSdei/Marlin_v1
...
Marlin v1, alignment of the Italian language
12 years ago
82e28851bd
Italian language: SD-Card change and SD-Card init
12 years ago
aed5965ad8
Italian language: remove space and some fix
12 years ago
d360846dd4
Update Marlin/language.h
...
Update Polish language #define MSG_RESUMING "Wznawiam drukowanie"
12 years ago
2f60e324dc
Fixed #394
12 years ago
5e2abfcdcd
Merge pull request #391 from STB3/Marlin_with_SD-Card_Change_Menu
...
Add SD-Card change and SD-Card init. for electronics equipped with LCD Display
12 years ago
a0d4e8e78e
Add Messages for SD Card init. & change
12 years ago
bbf0cc1379
Update Marlin/ultralcd_implementation_hitachi_HD44780.h
...
Fix to a bug that I just introduced - sorry. Forgot about offset of string length.
12 years ago
c8f1fbd9d8
Add SD-Card change and SD-Card init.
...
Add SD-Card change and SD-Card init. for reprap electronics without
SD-Chard change detect pin.
12 years ago
71ddb8dc60
Update Marlin/ultralcd_implementation_hitachi_HD44780.h
...
Use all available characters in narrow LCDs < 20 characters.
12 years ago
d2c547c407
Update Marlin/ultralcd_implementation_hitachi_HD44780.h
...
Fix to a minor bug with hardcoded LCD_WIDTH that draws edited values outside of the 16 characters width LCDs.
12 years ago
70871715e4
Added support for extruder offset handling
...
The extruder offset can be specified in the configuration
file or adjusted on the fly using the "M218 T# X# Y#" command.
The EEPROM support is not yet merged in.
The "T#" command can take option "F#" that specifies the feedrate
at which the printing head should be re-positioned. If not
specified the re-positioning move is not preformed immediately,
but the coordinates are adjusted for the printer to properly
position the head when the next movement happens.
12 years ago
49b2ddc8c1
Cleaned up non-standard characters
12 years ago
f8876a7958
Merge pull request #376 from kintel/skip_longfilenames
...
Also skip .files and _files with long filenames. I think its better than before. If somebody dislikes it, or wants additional configuration, it can be done in a future step. Thanks, Marius, and nice to have you helping!
12 years ago
18fcc367d2
Merge pull request #371 from Banjer/Melzi_LED_PIN
...
Chenged LED_PIN for Melzi boards, added comment about broken versions of...
12 years ago
19ce90fe02
Added comment about M42 usage (clean)
12 years ago
00fed0a703
Revert "Extended comment explaining M42 usage"
...
This reverts commit 01541ee64c
12 years ago
e06d820909
Also skip .files and _files with long filenames
12 years ago
01541ee64c
Extended comment explaining M42 usage
12 years ago
f24f02e212
compile fix: quickStop() needs stepper.h
12 years ago
12c41423ad
Fixed typo in comment
12 years ago
0995eaa492
Chenged LED_PIN for Melzi boards, added comment about broken versions of the Sanguino libraries
12 years ago
1d06b10962
Added a feature to have filament change by gcode or display trigger.
...
[default off for now]
syntax: M600 X[pos] Y[pos] Z[relative lift] E[initial retract] L[later retract distance for removal]
if enabled, after a M600, the printer will retract by E, lift by Z, move to XY, retract even more filament.
Oh, and it will display "remove filament" and beep like crazy.
You are then supposed to insert a new filament (other color, e.g.) and click the display to continue.
After having the nozzle cleaned manually, aided by the disabled e-steppers.
After clicking, the printer will then go back the whole shebang, and continue printing with a fancy new color.
12 years ago
408b349a84
Fixed #368 . Commented out the wrong pin definition, but explained why it is there.
12 years ago
9ecb267b63
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
12 years ago
3cf59f6f9a
add RepRapPro Huxley thermistor tables
12 years ago
c1730e2b08
Merge pull request #363 from yuroller/sanguino_panelolu
...
Panelolu pin assignment for sanguinololu
12 years ago
86358dd6cd
Panelolu pin assignment for sanguinololu from http://reprap.org/wiki/Panelolu
12 years ago
0f3f5d083d
Minor cleanup of the new FAN_KICKSTART code. #334
12 years ago
6ec56fa923
Merge pull request #334 from KevinOConnor/FanKick
...
Add feature to briefly run the cooling fan at full speed when it first starts.
12 years ago
965baf2683
Merge pull request #362 from daid/Marlin_v1
...
Finnish language
12 years ago
3d91bd486c
Add "kick fan" feature - briefly run fan at full speed on start.
...
Add a feature to run the cooling fan at full speed for a small period
(default 100ms) when first starting the fan. Some fans wont reliably
start spinning at low power, and many fans have issue with the PWM at
low power. However, once the fan starts spinning it can reliably be
set to a wide range of PWM values.
12 years ago
3f2f94ef28
Be consistent in setting of the fan PWM.
...
Always set the FAN PWM value in check_axes_activity() and always use
the value of the active move if a move is active.
12 years ago
7f30039d2a
+ Finnish translation
12 years ago
14e1d495ef
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
12 years ago
bbe7d3d0fe
Fixed #312
12 years ago
7ce509b9a7
Merge pull request #361 from yuroller/MakefileSanguino
...
Makefile sanguino
12 years ago
9c34c4f05b
fixes for ramps compilation using installed arduino ide
12 years ago
442ade15a6
Move Gen6 stuff into a proper location.
12 years ago
5fd4582cc8
Merge pull request #242 from Drakelive/Marlin_v1
...
Fixes issues # 216 and # 135 for Gen6 and Gen6 Deluxe board
12 years ago
8b88e3b386
Fixed #345 , Fixed #267 .
12 years ago
27843388c6
Merge pull request #360 from njprossi/Marlin_v1
...
Power signal control definitions for other power supplies
12 years ago
921273baa0
Added optional feature to stop printing when an endstop is hit. Made the Z display on the LCD in 3.2 format instead of 3.1. Added LCD message when and endstop is hit.
12 years ago
7d20ec706e
Added libraries from Arduino 1.0.3 for sanguino build
12 years ago
437eb3bafc
Initialize PS_ON at startup
12 years ago
f3c1fc70a9
Power signal control definitions for ATX and others
12 years ago
dad7691df9
makefile for sanguino standalone compilation
12 years ago
6752cb2d9c
PID now per extruder. Fixed typo
12 years ago
0ac452e252
Disable is now multi extruder compatible. M84 got a T option.
12 years ago
9e7b5056a0
{X,Y,Z}_{MIN,MAX}_POS are actually in Gcode coordinates.
12 years ago
5f82f03ff3
Add italian MSG_RESUMING.
12 years ago
5e3873c8db
Add german MSG_RESUMING.
12 years ago
01aac2a142
Small changes on the LCD panel, let the speed control work better, line up the parameter edit the same as the menu, remove some unused defines, and remove the Z from the 10mm move menu.
12 years ago
b69cb9fbd9
Change the end of SD cart print message from minutes/seconds to hours/minutes.
12 years ago
30254e3388
Merge pull request #350 from jcrocholl/Marlin_v1
...
Automatically set *_MIN_PIN and *_MAX_PIN according to *_HOME_DIR.
12 years ago
38ee395ac7
Replace the 1ms delay for 2 nops to get a 100ns delay. #259
12 years ago
5df5e4c4a2
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
12 years ago
a95dcd74e7
Fix some of the duplicated PSTRs, saving 500bytes of flash with LCD on.
12 years ago
8caf5d252d
Remove bogus blank line.
12 years ago
1c2ecddae4
Fix typo (# missing before define).
12 years ago
6dfb8a2187
Fix home_all_axis to make QUICK_HOME work with Repetier-Host which sends G28 X0 Y0 Z0 instead of G28. Thanks to Matt Schoenholz for reporting this issue.
12 years ago
3b2e5027e5
Merged updates from Marlin_v1.
12 years ago
b39f5d614a
For boards with only one endstop per axis, automatically set *_MIN_PIN and *_MAX_PIN according to *_HOME_DIR.
12 years ago
ab09fa4bbf
fixed pwm generation at pin D12 and D13 when one of them is used as FAN_PIN on Sanguino, added soft pwm entry for FAN_PIN in temperature.cpp
12 years ago
5697451c72
fix lcd class
12 years ago
58e806f3fa
Fix the russial translation.
12 years ago
50a5ce1dc4
deduplicate messages
12 years ago
6123a00e64
Fix the german translation.
12 years ago
7c21716886
Fixed #341
12 years ago
ae1bc83350
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
12 years ago
596a7e1904
Fix compiling for Arduin < 1.0.0
12 years ago
b264317fa0
Reverted the patch by KevinOConnor, as it crashes some versions of avr-gcc and caused linking issues.
12 years ago
673577a31b
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
12 years ago
23022f1a82
Updates to Makefile to compile for Teensy.
12 years ago
96e9db8919
Merge pull request #339 from KevinOConnor/CompilerFlags
...
Add additional optimization flags to Makefile
12 years ago
08356361ac
Fixing a problem with heated beds not working without PID and BED_LIMIT_SWITCHING
12 years ago
047d037f8c
#ifdef fix for #326
12 years ago
0908458381
Use gcc "-fwhole-program" optimization.
...
Use "whole program" and "link time optimization" features of gcc. The
whole-program optimization enables the compiler to evaluate the entire
firmware for optimization instead of just one code file at a time.
This leads to better overall optimizations.
12 years ago
16fbb455ef
Use linker "--relax" option.
...
The "relax" option enables the linker to convert certain "call"
instructions to the smaller "rcall" instruction. This reduces the
size of the resulting binary.
12 years ago
f30b46b2a8
One more fix for #338 , I really should get a heated bed to test with.
12 years ago
65c3f1ffcd
Most likely fixing #338
12 years ago
7577717b59
Fixed #336
12 years ago
1a8f54cea1
The big LCD code update. This splits the display and menu implementation. Paving the way for future different displays. It also makes it easier to modify the menu structures while keeping everything consistant. Note that this most likely breaks the translations, which need to be updated.
12 years ago
6731c094ee
Fix compiling with just an 16x2 LCD and no buttons.
12 years ago
b99a928a80
Fix the M117 (display message on LCD) when used over USB with checksums.
12 years ago
55ba90ac19
Add PID functional range setting. With high powered heaters the current functional range of 10 degrees causes high overshoots as the PID needs to kick in before the temperature hits 10 degrees below target.
12 years ago
5ff5cee8ce
Fix the sensitive pin definitions, there where analogue numbers in the digital pin list. Also made M42 without a P function on the LED_PIN (which was otherwise a useless pin definition)
12 years ago
8b58edc70e
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
12 years ago
d0319d45af
Merge pull request #335 from jcrocholl/Marlin_v1
...
Fix endstop pins for Printrboard
12 years ago
ca409e5531
Fix X/Y/Z_MIN_PIN for Printrboard.
12 years ago
1f45cb0a51
Fix typo in MANUAL_HOME_POSITION (plural S missing) and improve comments.
12 years ago
931a0052ea
Fix typo in MANUAL_HOME_POSITION (plural S missing) and reduce BLOCK_BUFFER_SIZE because 64 wasn't working for some reason.
12 years ago
46ec4b648c
Added some missing Mxxx comments to M commands. Fixed the unsetting of the timer dividers for the fast PWM fan.
12 years ago
724f5aa36b
Update on makefile for moved Arduino addons.
12 years ago
6d9dfa96c3
Move the Arduino related stuff out of the Marlin tree, as they are not directly related to Marlin functionality but addons for the Arduino IDE. Also split up the addons for pre 1.0.0 Arduino and post 1.0.0 Arduino.
12 years ago
3fb07d9b8d
Add MINTEMP/MAXTEMP error to LCD, and fix temperature bug with more then 1 extruder.
12 years ago
8e2519e88b
Add realtime delta geometry in Marlin_main.cpp.
12 years ago
cec7283b21
Enable QUICK_HOME for deltabot.
12 years ago
2292441f0c
Use X/Y/Z_MAX_PIN instead of X/Y/Z_MIN_PIN for top endstops on deltabot.
12 years ago
c430906d3b
Deltabot settings and configuration adjustments.
12 years ago
82c8724b33
Fix compile with PID_DEBUG
12 years ago
9b160972a1
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
12 years ago
e036750bdf
Use the disable macros on initialization. Which fixes a bug when there is no pin defined for stepper enabled (motherboard 4)
12 years ago
fcd9de72ef
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
12 years ago
32d4373e0f
Add printrboard and brainwave to Makefile.
12 years ago
b3ddbcee2a
Merge pull request #329 from jcrocholl/Marlin_v1
...
Add Printrboard and Brainwave to pins.h and fastio.h
12 years ago
29435dfb4b
Proper avr for Sanguino in Makefile.
12 years ago
52158dffcc
Big temperature code update. No longer converts back and forwards between temperature and raw sample value. Reducing complexity, removing code. Also named some variables better. While keeping the safety intact and functionality the same.
12 years ago
ca7acbe6d9
Allow specification of which arduino hardware subvariant in Makefile.
12 years ago
33247733e0
Teensylu and Printrboard use different analog pins for thermistors.
12 years ago
621c24a10f
AT90USB is only defined after pins.h is included.
12 years ago
6cba11f087
Stop redefining MOTHERBOARD and #define AT90USB instead. Also put #ifndef AT90USB around the HardwareSerial_h trick, so now Printrboard / Brainwave support compiles on Arduino 1.0.2 as well.
12 years ago
4d351b4846
Improved formatting and comments for consistency.
12 years ago
a30007caa4
If fastio.h is not messed up then Teensylu and Printrboard are actually using the same pins.
12 years ago
6aa87a7b67
Use the same fastio.h definition for AT90USB1286/7 and AT90USB646/7.
12 years ago
b1c38d4c82
Avoid compiler warnings (redefined MOTHERBOARD) in Arduino 1.0 and greater.
12 years ago
42e21bb06e
Add support for Printrboard (from https://github.com/lincomatic/Marlin ) and Brainwave (from https://github.com/metrix/Sprinter ).
12 years ago
ce4b5bbeaa
Add AT90USB646 support from Sprinter to fastio.h.
12 years ago
f413aa33b3
Small makefile change, posibility to add defines on the commandline, and fix compiling with watchdog enabled when using the Makefile.
12 years ago
587154c01b
Fix the WATCHPERIOD implementation. It did not work correctly in a multi extruder setup, it did not work after 32 seconds after startup (int16 used as millies timestamp). And it did not work if you gave an M104 or M109 when the target was already around the target setpoint. So on average, it did not work at all. The new implementation should be robust in detecting a failure to heat up.
12 years ago
1f27870d41
Fix compiling the watchdog error message when the manual reset watchdog is used.
12 years ago
c5d4225804
Mistake there, not sure why I did that. My bad.
12 years ago
529748894c
Minor changes in the temperature code for some cleanup.
12 years ago
4e26ecc940
The Partial release message (which does not really tell you anything) overwrites the final print time on the LCD, which is a real shame. So I removed the message.
12 years ago
c421774422
The Partial release message (which does not really tell you anything) overwrites the final print time on the LCD, which is a real shame. So I removed the message.
12 years ago
16078e47d4
Fixed #325
12 years ago
6a9bee27cc
Changed the naming of some LCD functions, so the names match better what the function does. Also moved around some prototypes for general cleanup.
12 years ago
94ea26ff46
Some minor changes on code style. And a bugfix where the counters for positioning in the stepper where wrong depending on compiler settings. (Caused strange values to reported back with M114 and endstop triggers). Also fixed compiling with FWRETRACT enabled.
12 years ago
6c51fe5039
Fix the bug where the SD percentage calculation is wrong when the file is larger then 42MB
12 years ago
Francesco Santini