8b12371e45
Change some hex case
7 years ago
4782acf60e
Merge pull request #8780 from fiveangle/bf2-typo
...
[2.0.x] typo in Marlin.cpp
7 years ago
0cd1e91056
[2.0.x] TMC driver update ( #8769 )
7 years ago
09d13f186f
Correct unskew, after all
7 years ago
0d531d9655
Missing HAS_HEAT_BED conditional
...
Fixes issue found in #8779
7 years ago
69efb87d19
typo in Marlin.cpp
7 years ago
368c124de8
Fix Planner::unskew parity with skew
7 years ago
cf2193c07f
Comment, fix filament width sensor
7 years ago
a641992c1d
Merge pull request #8762 from victorpv/patch-2
...
[2.0.x] STM32F1 HAL: Fix issue #8585 . Updates to readme.
7 years ago
ac168a03c8
Fixes for the Arduino DUE HAL (Serial Port, Graphics Display, EEPROM emulation) ( #8651 )
...
* Fixing the DUE serial port assignments: Now -1 means the SAM3x USB Device emulating a serial port, and 0 means the USB to serial adapter included as a programming port
* Improving the Fast IO port access implementation on Arduino DUE
* Implemented EEPROM emulation on Due by storing data on the internal FLASH (with wear leveling)
* Implemented a Software SPI for the ST7920 graphics display for the Arduino RAMPS for DUE, as the default one in u8glib is clocking data too fast on ARM, and the display does not understand it.
* Fixing the case where the serial port selected is the USB device
* Adding configuration for the Makerparts 3D printer (www.makerparts.net)
* Tuned MakerParts acceleration on X and Y axis so it never loses steps. Also adjusted pulses per mm to match default hw configuration
* Fine tuned Maximum acceleration for MakerParts printer
* Style cleanup
* Style cleanup (2)
* Style fixes (3)
* Fixing the DUE serial port assignments: Now -1 means the SAM3x USB Device emulating a serial port, and 0 means the USB to serial adapter included as a programming port
* Improving the Fast IO port access implementation on Arduino DUE
* Implemented EEPROM emulation on Due by storing data on the internal FLASH (with wear leveling)
* Implemented a Software SPI for the ST7920 graphics display for the Arduino RAMPS for DUE, as the default one in u8glib is clocking data too fast on ARM, and the display does not understand it.
* Fixing the case where the serial port selected is the USB device
* Adding configuration for the Makerparts 3D printer (www.makerparts.net)
* Tuned MakerParts acceleration on X and Y axis so it never loses steps. Also adjusted pulses per mm to match default hw configuration
* Fine tuned Maximum acceleration for MakerParts printer
* Style cleanup
* Style changes to u8g_dev_st7920_128_64_sw_spi.cpp
* Even more improvements to the FastIO HAL for DUE. Now WRITE() is 2 ASM instructions, if value is constant, and 5 cycles if value is not constant. Previously, it was 7..8 cycles
* After some problems and debugging, seems we need to align the interrupt vector table to 256 bytes, otherwise, the program sometimes stops working
* Moved comments out of macro, otherwise, token pasting does not properly work sometimes
* Improved Software SPI implementation on DUE: Now it honors the selected speed passed to spiInit(). This allows much faster SDCARD access, improving SDCARD menus and reducing latency
* Update u8g_dev_st7920_128_64_sw_spi.cpp
* Disabling EEPROM over FLASH emulatiion if an I2C or SPI EEPROM is present
7 years ago
084f2434a7
Update readme.md
7 years ago
7c7ae5ebef
Delete duplicated file.
7 years ago
4feffca178
fix for issue #8585
...
As reported in this issue:
https://github.com/MarlinFirmware/Marlin/issues/8585
I have it working fine in my local copy like that change.
7 years ago
d568e586b7
Fix up ubl_motion indentation
7 years ago
24f9bec6f4
UBL + DUAL_X_CARRIAGE compatibility
7 years ago
6d0678d963
Omit unused UBL motion code
7 years ago
3255712343
Skew Correction for UBL
...
Also remove unused grid slicing function when using UBL segmented.
7 years ago
3d796d8040
Move debug code
7 years ago
3db5303bfe
_buffer_line => buffer_segment
7 years ago
a71d2f3f40
UBL_DELTA => UBL_SEGMENTED
7 years ago
73e32925e4
References are better for array args
7 years ago
125c572d97
Tweak M114 detail
7 years ago
a5150c83a2
[2.0.x] Multiple updates to STM32F1 HAL ( #8733 )
...
* STM32F1 HAL
Adding files for STM32F1 HAL based on libmaple/stm32duino core.
Current persistent_store uses cardreader changes to be sent in separate
commit, but could be changed to use i2c eeprom.
There is another persistent_store implementation that uses the MCU flash memory
to emulate eeprom
Adding readme with some information about the stm32 HAL.
* Switch to Timer4 to avoid a hard reset on STM32F103C6 boards
On bluepill STM32F103C6 boards, using Timer5 results in a error() vector call. Switch to 4 since these are both general purpose, 16 bit timers.
* Add support for EEPROM emulation using Flash
Some low end machines doe not have EEPROM support. Simulate it using the last two pages of flash. Flash does not allow rewrite between erases, so skip writing the working version if that's enabled.
* Basic Pins for a malyan M200
This is a work in progress to go hand in hand with the STM32 work.
* Add support for ADC with DMA. This work has exposed a problem with the pin enumerations in STM boards vs what marlin expects (i.e, try defining PA0 as a temp pin). The hack can be removed with we go to fastio completely. To see this work, set something in adc_pins to a value like PA0 and connect your pullup resistor'd thermistor.
* Missing file - change HAL_adc_init to actually do something
We have an actual ADC init function now.
* Remove pinmode hack
Remove the pin mode hack that I was using to init PA0.
Updated Readme.md
* Several changes to timers and GPIO
Faster GPIO, and faster timer functions by accesing registers and
libmaple.
Still more changes pending for the Timer's code to skip using the
HardwareTimer class altogether.
Switch all enums to be within #defines
This change allows a user to have, for instance, TEMP_4 and TEMP_BED definied but nothing else. The enums which are not defined move "out", allowing the first ones to take the slots in the enum, and since the array is sized on ADC_PIN_COUNT, we always have the right size data and in order.
* Update Malyan M200 pins
Update Malyan M200 pins with correct fan values.
* Test all pins on actual hardware, update definitions
Some of the pin definitions were from knowlege base/pdfs. Now they've been tested against actual hardware. This should be very close to final.
* Update HAL_timers_Stm32f1.cpp
* Add sample configurations for Malyan M200
Add sample configuration for Malyan M200 without bed leveling, and move fan to auto cool E0 since this printer by default has only one fan.
Choose the timer based on MCU defintion. Timer5 is not valid on C8/CB class boards, so use Timer4 for the step timer.
readme.md update
* Updates to timers, and some stm32 boards definitiions
* Correct pin toggle macro.
* Remove duplicated Malyan M200 entry from pins.h
* Update configuration_store.cpp
* Formatting, indentation
* Formatting in HAL_Stm32f1.cpp
7 years ago
204199e1ce
Only compare XYZ to check motion
7 years ago
6686d937fb
Always report position on config load/reset
7 years ago
117fc872a7
Update current position in M852
7 years ago
7d2e850577
Have M420 report a changed position
7 years ago
03ba79f144
Sync and report changed position
7 years ago
5cf6a062e3
Reset timer count before first block step
7 years ago
6149b82119
Allow setting current timer counter
7 years ago
82ef6b5242
Add an option to specify "pulse" timer
7 years ago
b8bc965414
General cleanup HAL timers
7 years ago
69d49a2438
Shorter segments may be better
7 years ago
d576f5408e
Add MiniRAMBo 1.0a board
7 years ago
c40cb52342
Use MB() for Megatronics 3.1
7 years ago
4fa65a5c25
TCNT0 => HAL_timer_get_current_count
...
Fix #8710
7 years ago
b3daf6b5db
[2.0.x] better reverse pass ( #8722 )
...
* repair reverse_pass()
And make it readeble.
This was broken a long time ago.
Not competely unfunctional but far from optimal.
* Minor speedup when calling calculate_trapezoid_for_block
2 float / to 1 foat / and 2 float *
* Various style changes
7 years ago
f58eb391aa
[2.0.0] Better off mesh behavior for UBL ( #8714 )
...
* Better off mesh behaviour for UBL
* Suggested ubl.h changes
7 years ago
cffd052fee
[2.0.x] Fix for #8604 ( #8717 )
...
* Nozzle.cpp: replace incorrect M_2_PI (2/pi) with 2.0 * M_PI
* Use RADIANS(360) instead of 2 * M_PI
7 years ago
65d0f32f82
divide only when required
7 years ago
728acf521c
Followup to #8706
7 years ago
85c6ffbe0d
Discard all "continued" blocks on interrupted move
7 years ago
4e891e9fb7
Followup to #8698
7 years ago
de3d3b9cb1
Put FORCE_INLINE before static
7 years ago
43ea265b78
Merge pull request #8685 from MateuszKrawczuk/patch-3
...
Update TEMP_BED_PIN in MIGHTYBOARD_REVE
7 years ago
ae663a4198
PROBE_DOUBLE_TOUCH => MULTIPLE_PROBING
7 years ago
d7800e7975
Apply MULTIPLE_PROBING to example configs
7 years ago
542efda7db
Merge pull request #8698 from thinkyhead/bf2_replace_jerk_code
...
[2.0.x] Improved Core-compatible jerk code
7 years ago
3cd7659924
Improved Core-compatible jerk code
7 years ago
99fcf60977
[2.x] addressing #8644
...
Removed missing include file
7 years ago
81c0a918af
feed_factor => inverse_secs
7 years ago
f206b81cf7
Sanity check skew+UBL
7 years ago
9898b96992
No lcd_map_control flag in quick_stop
7 years ago
840289e7cc
Use block cleaning instead of split flag
7 years ago
90cf6a06be
Simplify G26 user_canceled
7 years ago
cdfabbc507
Shorten error text in G29
7 years ago
c846388a65
Standardize LCD interface code for UBL a little
7 years ago
2fde60da12
Changes for parity with 1.1.x
7 years ago
6040d4080e
Cleanup stepper ISR. Allow cleaning for endstops.
7 years ago
a4e1d83599
Fix M503 S parameter
7 years ago
a3b098b4be
Whitespace clean
7 years ago
a993c5227d
Don't split first_move while homing or probing
...
While homing or probing it might be bad if the stop/trobe triggers during the first part and the second is still in the buffer.
7 years ago
5320906b0b
Update TEMP_BED_PIN in MIGHTYBOARD_REVE
...
Pin K7 number in fastio1280.h is 69, but it's also ADC15 pin.
To get correct value from ADC reading it should be set as 15.
7 years ago
aeb5c623c1
Show "Level Bed Corners" with UBL too
...
Addressing #8676
7 years ago
5fbb2f121e
Remove skew warning that could crash the planner
7 years ago
c1184552ac
Change K1 to required option PID_K1
7 years ago
9e3fbcf35c
fix for #8669 ( #8679 )
...
* fix for #8669
* Update G28.cpp
7 years ago
d8b444c144
Cleanup constextpr in planner.cpp
7 years ago
a2372cfab5
Fix SKEW_CORRECTION without leveling
7 years ago
4d3c3d0b73
Some ST7920 parity with 1.1.x
...
Possibly more should be brought over? Discussion at #8471
7 years ago
3748c28924
Fix MBL G29 without LCD
...
Addressing https://github.com/MarlinFirmware/Marlin/pull/8575#discussion_r154536617
7 years ago
772298257b
Creality pins spacing, MINIPANEL CS pin
7 years ago
b27bc67271
Set initial endstops state
7 years ago
b6ba32ce75
Support for RAMPS Plus (3DYMY)
7 years ago
53694ebaa1
Folllwup to planner splitting
7 years ago
37fff608b0
Merge pull request #8652 from fiveangle/bf2_usbcon_xonxoff
...
[2.0.x] SERIAL_XON_XOFF not supported on USB-native AVR devices
7 years ago
4b612f590c
Split first move to planner for better chaining
7 years ago
91b63f6d69
SERIAL_XON_XOFF not supported on USB-native AVR devices
...
User could enable SERIAL_XON_XOFF on USB-native devices and it would not be enabled without warning, but M115 would report the capability as available.
7 years ago
57fac33a74
add explanations
...
1) add explanations as to why software SPIs are selected
2) remove unused flag/option
7 years ago
bb23286383
add README & modify spi_pins.h
...
still trying to fix file name
7 years ago
dd8febca1a
Revert "Merge pull request #8611 from thinkyhead/bf2_planner_split_first"
...
This reverts commit 824980e70eaa7efb96bf
7 years ago
fb44f8e50f
Merge pull request #8616 from hg42/bugfix-2.0.x
...
[2.0.x][LPC1768][FIX] NUM_DIGITAL_PINS was negative, fixes PWM, arduino io functions, M42, M43, M226, probably also Servo, some LCD, soft spi, SoftwareSerial, ... may be others
7 years ago
4c5356f77a
Merge pull request #8622 from hg42/implement-LPC1768-GET_TIMER
...
[2.0.x][LPC1768][fix] Implement GET_TIMER and other GET_xxx, fixes PWM
7 years ago
f5b4e1ef4f
as a workaround enable PWM for any pin, see PR #8622
7 years ago
6e944a413c
Merge pull request #8607 from benlye/patch-1
...
[2.0.x] Fix M49 so that it does not hang the terminal console
7 years ago
967522b95e
Merge pull request #8615 from dot-bob/Duplicator_6-2.0.x
...
[2.0.x] Example configurations for Wanhao Duplicator 6
7 years ago
f4b16a3bac
Update M49.cpp
7 years ago
f9327534f8
Merge pull request #8634 from fiveangle/bf2_report_xonxoff
...
[2.0.x] Report SERIAL_XON_XOFF in M115
7 years ago
da9f140829
Merge pull request #8637 from thinkyhead/bf2_ubl_uses_LSL
...
[2.0.x] Use custom segment length for UBL Cartesian
7 years ago
3a97de52ef
Split first move to planner for better chaining
...
Address #8573 , #8595
7 years ago
24437de591
Use custom segment length for UBL Cartesian
7 years ago
4c5ffd2349
[2.0.x] Report SERIAL_XON_XOFF in M115
...
-Report SERIAL_XON_XOFF in Extended Capabilites M115 report for hosts
-Remove outdated 256 size limitation from comments on RX_BUFFER_SIZE defines
-Update error message conditions
7 years ago
aa7efb96bf
Bring configurations up to date
7 years ago
63a91cd37a
Fix a homing comment
7 years ago
8056120195
Rename inverse_mm_s => inverse_secs
7 years ago
23557f8e77
Remove obsolete de_float
7 years ago
05f8e98c4a
Fix for issue #8629 - mismatch between number of stored and loaded dummy items on non-delta machines. ( #8631 )
7 years ago
48fb4e0932
Get Bi-Linear to work with G26
...
More corrections to make that happen...
7 years ago
0850b38b45
Get Bi-Linear working with G26
...
G26 uses logic that looks like:
```
ex = _GET_MESH_X(i + 1) - (SIZE_OF_INTERSECTION_CIRCLES - (SIZE_OF_CROSSHAIRS));
```
The Bi-Linear macros need parenthesis to work correctly.
7 years ago
000b3b3117
Comment/cleanup of motion code
7 years ago
046a1ad331
Merge pull request #8625 from tcm0116/2.0.x-G33
...
[2.0.x] Fix missing return values in G33_auto_tune
7 years ago
b35c3b5eb8
Fix missing return values in G33_auto_tune
7 years ago
45c2388a58
Apply const to thermal_runaway_protection args
7 years ago
0154e3480c
New feature: BED_SKEW_CORRECTION
7 years ago
082ab8fcab
Add SKEW_CORRECTION to example configs
7 years ago
d1f11e9c10
fix missing GET_TIMER (used by PWM for Ex_AUTO_FAN)
7 years ago
dd1b503f64
fix NUM_DIGITAL_PINS being negative for more than 127 digital pins
7 years ago
bd45d0363d
Add default configurations for the Wanhao Duplicator 6.
7 years ago
91fb6231b2
Fix EEPROM V45 header, layout
7 years ago
94e6b2976e
Restore correct G26 values for gMax 1.5+ printer
7 years ago
dd3ce40826
Drop Planner::position_float, use int types
7 years ago
ec6ca37ed3
Fix (un)apply_leveling fade bug
7 years ago
a52fec6ac4
Planner class parity with 1.1.x
7 years ago
1f3ad461bc
Update M49.cpp
...
Fix M49 so that it does not hang the terminal console.
7 years ago
e37dd64548
Apply LEDColor, language fixes
7 years ago
8f90642eea
LED_CONTROL_MENU config changes
7 years ago
cf0f78336b
New Feature: LED_CONTROL_MENU
7 years ago
23e45fa3c4
Apply const to some planner vars
7 years ago
7c61bcb058
Apply SEGMENT_LEVELED_MOVES to example configs
7 years ago
ef2531558c
Add an option to segment leveled moves
7 years ago
285b868e9b
Tweak planner code style
7 years ago
1f2acc33bc
Tweaks for check_axes_activity
7 years ago
7f88334aa3
Done cleanup and removed duplicates in pins_RuRAMPS4D.h ( #8582 )
...
Remove duplicates, with followup fixes
7 years ago
a8aa43ce2d
Merge pull request #8587 from AnHardt/2_Fix_WDTO_during_long_DELTA_moves
...
[2.0.x] Fix WDTO during long delta moves
7 years ago
4793c34c53
Fix M290 boolval bug
...
Fix #8577
7 years ago
16baa48699
Fix #8579
...
Fan speed code fell into a curly brace
7 years ago
02aa93a6ad
Fix Watchdog time out during long lasting DELTA moves
...
During long lasting moves of a delta machine neither the temperatures are maintained nor buttons checked nor ... .
The fix is to call 'manage_heater()' and 'idle()' every now and then in the loop where the move is segmented.
The code is abot the same as in G2_G3 wher we had the same problem with too large circles lasting too long.
Fixing #7510
7 years ago
fadf9eb2d7
Simplify midpos calculation
7 years ago
0880031e8e
Satisfy M702 dependencies
7 years ago
0786b61ce7
Followup to #8575
7 years ago
276271e72f
Make MBL work more like PROBE_MANUALLY
7 years ago
94cb412e45
Allow override of probe bounds
7 years ago
c8718aa111
Spacing, macros in LPC1768_PWM
7 years ago
a67cf78c6b
Clean up whitespace, spacing
7 years ago
f0dd4e3fa0
Bootscreen parity with 1.1.x
7 years ago
b634bfe1b1
Tweak to readDir code
7 years ago
7be4857ab9
Tweak BLOCK_BUFFER_SIZE description
7 years ago
7d8b66e207
Merge pull request #8570 from Bob-the-Kuhn/Sbase-PWM
...
[2.0.x] MKS Sbase - add servo pin definitions and add directly controlled PWM
7 years ago
59b32c25b5
MKS Sbase changes
7 years ago
f90c075d1f
SD Menu patches
7 years ago
9b64be0bc5
Fixes for leveling sub-menus
7 years ago
25674da90c
Tweaks to do_blocking_move
7 years ago
22b897e77d
Show M211 output with workspace offset
7 years ago
d06e29846d
Loosen HAS_BED_PROBE definition
7 years ago
e48fcad615
change G26 and G29 bit function names to avoid HAL collision
7 years ago
41ec449960
Fix G26 error return
7 years ago
9badf5dc0d
Fix Micromake C1 config
7 years ago
7576ad7fc2
Merge pull request #8554 from tcm0116/2.0.x-cleanup
...
[2.0.x] Fix for #8525 and other cleanup
7 years ago
27c5692b13
Syntax tweaks
7 years ago
d18d40e1d6
M290 report on change, P0 to leave Probe Z Offset alone
7 years ago
65f365333f
[2.0.x] G33 probe error handling
7 years ago
8c69adba8b
Merge pull request #8553 from Bob-the-Kuhn/2.0.x-U8Glib-follow-up
...
[2.0.X] U8Glib follow up
7 years ago
be00e421a7
Patch up M290, M851
7 years ago
fc40d56131
fixed error, updated defaults, added notes
...
Travis fix - only allow ultralcd_st7920_u8glib_rrd_AVR.cpp to compile when ST7920 selected
7 years ago
d29cb646e3
Fix erroneous reference to temperature in time calculations
...
Travis is having problems at: https://github.com/MarlinFirmware/Marlin/pull/8560
So... doing a direct commit to get things correct. Bugfix_v1.1.x does not have this bug. Nothing needs to be done to that branch.
7 years ago
7bb1721f35
Fix _BV already defined warnings for Teensy
7 years ago
5f9592a523
Cleanup narrowing warning in pin_is_protected
7 years ago
34eaaab5fb
Fix _BV already defined warnings
7 years ago
2ea779e560
Allow bed probe sanity checks to run
7 years ago
d24b1190bd
Don't use Z_MIN_PROBE_ENDSTOP on DELTA
7 years ago
e34c6827ea
Init MIXING virtual tools as switching
7 years ago
a9ecb975b2
Apply LINEAR_UNIT to M503 output for M200
7 years ago
d95ee0f003
Merge pull request #8551 from revilor/bugfix-2.0.x
...
MK2_MULTIPLEXER does not require E2/E3 stepper pins
7 years ago
80ada58818
One fewer function call in probe_pt
7 years ago
92a0dc552a
MK2_MULTIPLEXER does not require E2/E3 stepper pins
7 years ago
b49acce035
Tweaks for lcd_external_control
7 years ago
1ef1052ae1
Phatter arrows for Z offset overlay
7 years ago
5926c9c97b
Followup for MESH_EDIT_GFX_OVERLAY
7 years ago
ab03a31cc9
Patch G0/G1 for NANODLP_Z_SYNC
7 years ago
a766dfb3b1
Merge pull request #8536 from thinkyhead/bf2_nanodlp_z_move_sync
...
[2.0.x] Implement NANODLP_Z_SYNC for 2.0.x
7 years ago
01e207213f
Fix MK2_MULTIPLEXER stepper indirection
7 years ago
ec04cf27d3
Fix the G26 out of scope identifiers in the v2.0.0 branch ( #8543 )
...
These changes may need to be warmed over. I tried to fix things with
the least amount of disruption. I just wanted to get the bugfix_v2.0.0
branch working for people again.
7 years ago
dc82babe8e
Implement NANODLP_Z_SYNC for 2.0.x
7 years ago
c6b0c104bb
Adapt G26 to work for all meshes
7 years ago
5ce7f23afa
Config option G26_MESH_VALIDATION for all meshes
7 years ago
c19eb33408
Move G26 to gcode sub-folder
7 years ago
a03f93bab4
Fix fan kickstart
7 years ago
9e3c41f9e8
Tweak fan kickstart / speed code
7 years ago
118ac61e59
[2.0.x] Tool change bad behaviour fix
...
Previous fix did not work as expected when axeis not homed. It raise Z but never return to original position
7 years ago
c35d27f77c
Merge pull request #8299 from tcm0116/2.0.x-BIQU_BQ111-A4
...
[2.0.x] Add BIQU BQ111-A4 board
7 years ago
1685cd193b
Tweak char_mode init
7 years ago
9406c87a97
Fix up LCD init / charset
7 years ago
fa577392b2
Add BIQU BQ111-A4 board
7 years ago
c2fc78c3a8
#ifndef => #if !PIN_EXISTS
7 years ago
c613a1ed38
Fix indentation, stepper.h dependency, etc.
7 years ago
f011a32771
Board definitions for Ultratronics Pro v1.0
7 years ago
9dad534f02
fixed
7 years ago
4371345cbe
Don't re-init graphical LCD after boot screen
...
Followup to 13a3fb1acc
7 years ago
56c02b7f59
Shift register buttons question
...
Can LCD shift registers keep up with faster MCUs?
7 years ago
3994d3b935
General cosmetic LCD
7 years ago
617993d0ea
Patch for !!TEST (was _BV once?)
7 years ago
3269d8dd62
Tweak M42 var
7 years ago
bb1a6eea88
Remove pin count check for MIGTHYBOARD_REVE
...
Remove assert and unused code since it is implemented in pinsDebug_plus_70.h
7 years ago
1ce0fb336b
Patch Max7219_LED_Set input args
7 years ago
a61127a421
[2.0.x] tool change bad behaviours
...
This will solve 2 issues on tool change.
1) when no home is done ("no_move" is set) tool change should never move X & Y because... I don't know where I am...only Z should be adjusted to avoid bed collision if other nozzle is lower than current.
Since no move no bed level matrix should be applied
2) When SWITCHING_NOZZLE is enabled and system is homed there are two movements to go to destination, but first can move Z to older position and then crash on the bed
7 years ago
e2724c68ab
Update pins_RURAMPS4D.h
...
Add and bugfix pins
7 years ago
9770062309
Merge pull request #8463 from thinkyhead/bf2_32bit_M42
...
[2.0.x] Updates to Anet A8 configurations
7 years ago
3066655727
Try port*100+pin, fix config dependency
7 years ago
ba8bc7ea80
Cosmetic tweaks
7 years ago
f409147116
Fix P2_04, P2_05
7 years ago
a28ccabe2a
M42 P1.20 fix
7 years ago
33912fa7e8
Update Temperature::setPwmFrequency prototype to match source
...
Introduced with #8446
7 years ago
b9327a4d16
Misc. general cleanup
7 years ago
8836623e0f
Fix `sq`/`min`/`max` macros after platform headers
7 years ago
fe4f009fdd
32-bit unless…
7 years ago
25af9decfe
Remove enum.h include of MarlinConfig.h
7 years ago
1d4571b88d
Dependency adjustments
7 years ago
550f1025f0
Try using <Arduino.h> everywhere
7 years ago
c0000a0cdc
Move servo code to modules/servo.*
7 years ago
81bc428b48
Don't compile custom u8g without DOGLCD
7 years ago
c14000775b
PWM fixes, slow down fan update
...
include LPC1768 syntax for M42
couple more pin_t changes
consistency
change M42 to R, P format
Revert "change M42 to R, P format"
This reverts commit 01f12f579ec9ccc1bb9126e68d2c86449e9b7edf.
7 years ago
60adc6ff02
Display filwidth ratio in terms of E mm
7 years ago
6e533748eb
Fixes #8472
7 years ago
485abb023b
Merge pull request #8456 from thinkyhead/bf2_wednesday_tweaks
...
[2.0] No retroactive adjustment with M851 Z
7 years ago
3bba7d60f3
No retroactive changes with M851 Z
...
If using babystep to adjust the Z probe offset, the axis will move and the mesh will be updated at the same time, causing a doubling of the Z offset over the rest of the print.
To correct for this, the current Z position would need to be modified in the opposite direction, canceling out the additional Z offset added to the mesh. This would be confusing to users, and moreover it would not be accurate without also taking the current Z fade level and current Z height into account.
It might make sense to change the mesh in the case where no babystepping is taking place, but this could be considered an undesirable side-effect of changing the `zprobe_zoffset`.
One way to remedy this would be to return to storing the mesh with `zprobe_zoffset` included, then subtracting `zprobe_zoffset` from the returned Z value. Thus, a babystep moving the Z axis up 1mm would subtract 1 from `zprobe_zoffset` while adding 1 to all mesh Z values.
Without including the `zprobe_zoffset` in the `z_values` there is no safe way to alter the mesh in conjunction with babystepping, although it's fine without it.
7 years ago
32512332df
Apply some formatting
7 years ago
7dacc999b9
Remove obsolete show_bootscreen var
7 years ago
9729528d13
Update UBL's Delta Probable locations
...
This is a non-intuitive change. @oldmcg says in this post https://github.com/MarlinFirmware/Marlin/issues/7572#issuecomment-340641207 that using DELTA_PRINTABLE_RADIUS is better than DELTA_PROBABLE_RADIUS for setting the probe limits. This is because the automatic probe code checks all locations for being reachable by the probe prior to doing the probe.
7 years ago
d48cb6bf41
Apply coding standards to Max7219
7 years ago
bd8bcf06e7
Updates to Anet A8 configurations
...
Based on #8426
7 years ago
7eea000f4b
E0 auto fan fixes
7 years ago
b2dda096fe
Fix FILAMENT_LCD_DISPLAY for disabled state
7 years ago
1e8afb66b7
Fix a planner comment
7 years ago
50f09cc029
Miscellaneous cleanup
7 years ago
63257dc083
Fix M503 output for M145
...
Fixes #7978
7 years ago
0918dae66e
Add OV() macro for use in thermistor tables
7 years ago
24057270a3
Merge pull request #8420 from RowanMeara/rm-dithering-2.0.x
...
[2.0.x] Fix Software Fan PWM
7 years ago
5079a02c90
Add HAL_SERVO_LIB to HAL_Due.h
7 years ago
9c3761047e
Merge pull request #8434 from thinkyhead/bf2_fix_M32_subroutines
...
[2.0] Fix 'M32 P' subroutines
7 years ago
e0d367f1fb
Fix M32 P subroutine handling
7 years ago
9f8b4c5ee8
Patch SD lib files for readability
7 years ago
2c8c30437e
Fix parser parameter value handling
7 years ago
6131533157
Change dithering behavior to intended.
7 years ago
e70b44dc0b
Make sure leveled[] is defined for later use
7 years ago
54774841ba
Merge pull request #8416 from thinkyhead/bf2_M114_DETAIL
...
[2.0] Add M114_DETAIL to Configuration_adv.h
7 years ago
009e3a7aa7
Add M114_DETAIL to Configuration_adv.h
7 years ago
6d6c3b1e97
Fix up REPRAPWORLD_KEYPAD defines
7 years ago
3f0a982b8c
Move Filament Width Sensor to Configuration_adv.h
7 years ago
b76e173205
Move test extrusion options under G26
7 years ago
14ebedca27
Drop unused LARGE_FLASH option
7 years ago
b7feb53e8a
Support for Extrudrboard in Printrboard Rev.F
7 years ago
91baca6abb
Patches for compiler warnings/errors
7 years ago
2f73dec077
Apply native workspace fixes for G92, G53-59
7 years ago
04abd8d459
Improve and clarify M428 code
7 years ago
c009a990e4
[2.0.x] Fix some 8-bit Teensyduino compile warnings ( #8385 )
...
* Fix some 8-bit Teensyduino compile warnings
-Override Teensyduino legacy NOT_A_PIN 127 define
-some fixups for Printrboard_RevF pins
* Proper cleanup of Printrboard Rev.F pins
* Apply LCD fixes to Printrboard v1
7 years ago
e8e92f8969
No leveling data in M114 if no leveling is enabled
7 years ago
f5d210c35c
Fix report_current_position
7 years ago
faaae7a1b2
Provide more clearance for BL-Touch probe
7 years ago
06ee6584fd
Remove offsets from soft endstops, tool change
7 years ago
c938273bd5
Coding standard patch of M290
7 years ago
98c1265e3b
Disable laser power when PWM goes to 0
7 years ago
d4a1154c25
Use do_blocking_move_to where possible
7 years ago
36426af564
Merge pull request #8356 from tcm0116/2.0.x-M600
...
[2.0.x] Normalize load/unload length in M600
7 years ago
1ed86adf9c
Cleanup around updatePID
7 years ago
75a58ee4b8
Fix position_is_reachable bug in waiting
7 years ago
e334efb2a7
PROBE_MANUALLY etc.
7 years ago
b6415dc169
finish
7 years ago
0efa66be0b
Updates to Traditional Chinese
...
From @cheton at #8347
7 years ago
cba9c1cf9e
Add pre-calculated planner.e_factor
7 years ago
600c85226e
Normalize load/unload length in M600
7 years ago
81b91b3f9d
Clean up some trailing white-space
7 years ago
2f9848ede3
Correct gMax 1.5+ example file
...
And... Keep both branches in synchronization.
7 years ago
006dad4b52
Add pins_RURAMPS4D.h & change pins.h
...
http://3dtoday.ru/blogs/svs0724/ruramps4d-ramps-for-adruino-due-the-pilot-shipment-available-for-zack/
7 years ago
00514857e9
SBASE serial port -1, RAMPS spacing
7 years ago
c66696c507
Merge pull request #8344 from tcm0116/2.0.x-delta_height
...
[2.0.x] Add delta_height variable in lieu of using home_offset
7 years ago
22e18fe832
Patch _manual_goto_xy for kinematics
7 years ago
0cfb936dd1
Clarify some motion code
7 years ago
f34c3597dc
Add delta_height variable in lieu of using home_offset
7 years ago
d47fbf791b
Arduini IDE compatibility changes
...
changed includes to make Arduino IDE happy
7 years ago
95ea43bde4
Update XYZ dual stepper configurations
7 years ago
b0b4a20930
Tweaks to core motion code
7 years ago
8805e24cc7
Fix tilt_mesh_based_on_probed_grid output bug
7 years ago
24437fbb13
Fix G26 Y argument bug
7 years ago
09b05c9d79
Merge pull request #8321 from Bob-the-Kuhn/pins_re-arm
...
2.0.x - pins_RAMPS_RE_ARM.h - add mega2560 pin numbers
7 years ago
e6788bb6ae
Fix get_destination_from_command for E
7 years ago
967104e1ce
Default Extrusion Settings were off a few lines in some of the example config files. ( #8333 )
7 years ago
8875885a15
pins add old names
...
fix typo
re-write PWM section, add "not on Re-ARM" list
7 years ago
1c6e83c137
if !HAS_MESH we still need to do some motion! ( #8328 )
...
* if !HAS_MESH we still need to do some motion!
Thank You MagoKimbra !
* Ooops.... need #else and not #elif
7 years ago
82f45c3e6a
Patch G33 misuse of PROBE_MANUALLY
7 years ago
064e6fe60e
Remove debugging pin toggle from LCD code
7 years ago
0483a7df91
AVR RRD works
...
LPC1768 VIKI2 & RRDFG are working
looks like all SPIs are working
library change
sh1106 locks up
fixed lockup, started I2C SW com
pretty
re-org
restore a few files
make library happy
switched HAL version of rrd
fix travis error
travis error fixes
another travis fix
cleanup
minor update
one more
correct spacing in platformio.ini
7 years ago
96c9d715f3
Patch abuse of sprintf_P in G33
7 years ago
ed62c621d7
Fix G26 Circle Drawing. Add Default Extrusion Settings ( #8313 )
...
- Fix G26 Circle Drawing.
- Add default extrusion settings so machine can print lines on print bed
- Yet to be done: Get LCD Menu's to use these settings.
7 years ago
8fea26aa9d
Fix PID_autotune watch temp increase value
7 years ago
2c099fd4c2
Update Thermal Protection Documentation
7 years ago
a6160916b0
[2.0] Fix M48 for delta printers/ABL compile issue ( #8286 )
...
* fix M48 for delta printers
fix M48 for delta printers. home printer if not already homed.
* remove ENABLED(DELTA)
remove ENABLED(DELTA) as it is not needed.
* Update M48.cpp
* abl needs queue.h
without queue.h abl will not compile since there is a script that runs at the end of it and we need to queue it up.
7 years ago
17ef0a513b
Update G92 for native workspace
7 years ago
b4bf8928aa
German language updates
...
Corresponding to #8306
7 years ago
73ca5345e1
Fix Delta EEPROM
7 years ago
714d2b9bbc
Merge pull request #8297 from thinkyhead/bf2_M118_and_others
...
[2.0] Fix M118, compiler warnings, etc.
7 years ago
83555933aa
Add platformio support for stm32 ( #8246 )
...
[2.0] Add platformio support for stm32
7 years ago
85a62bbf46
Misc. fixes to compiler warnings, etc.
7 years ago
e6aba99f16
Fix M118 parameters, with strict guideline
7 years ago
e9b1944a67
Patch non-extended font option
7 years ago
6324b09934
Revert "Fix EEPROM crc ( #8284 )" ( #8292 )
...
This reverts commit 172c36f517
7 years ago
172c36f517
Fix EEPROM crc ( #8284 )
7 years ago
cc4d28b73c
Update bilinear for native workspace
7 years ago
94c7205d64
Merge pull request #8281 from thinkyhead/bf2_alligator_dac
...
[2.0] Use fastio for Alligator dac084s085, etc.
7 years ago
2246316605
Fix name collision. timer_t => hal_timer_t
7 years ago
4efaef7039
[2.0.x] Fix archim2 SSDS define ( #8278 )
...
* Fix SSDS define
* Update pins_ARCHIM2.h
7 years ago
c8dfa26bc8
Use fastio for STM32F1 endstop interrupts
7 years ago
185dec800b
Use fastio for HAL SPI EEPROM
7 years ago
297666ea14
Use fastio for Alligator dac084s085
7 years ago
c5d95d318b
Merge pull request #8249 from thinkyhead/bf2_nozzle_cleanup
...
[2.0] Cleanup Nozzle class, fix XY vs Z move order
7 years ago
7e2fee9d56
Merge pull request #8274 from tcm0116/2.0.x-re_arm_D8
...
[2.0.x] Correct RAMPS_D8_PIN for Re-ARM
7 years ago
59c558d612
Merge pull request #8275 from GMagician/2.0.x-Typo-fix
...
[2.0.x] typo fix (removed spaces)
7 years ago
be73d5cc08
Cleanup Nozzle class, fix XY vs Z move order
7 years ago
9e93b7ccbd
[2.0.x] removed spaces
...
Removed spaces in array declaration
7 years ago
b91a822d7a
Correct RAMPS_D8_PIN for Re-ARM
7 years ago
d295f984e3
Update fwretract.cpp
7 years ago
1b40e9c464
Implement CNC_COORDINATE_SYSTEMS
7 years ago
1b42fba39b
Add CNC_COORDINATE_SYSTEMS to configs
7 years ago
a22434508f
Match tweaks to G33 from 1.1
7 years ago
c07bbd4154
Prettify some EEPROM code
7 years ago
d6aa127c76
Remove I2CPEM workspace offset
7 years ago
79772219ae
Fix Fan Multiplexer init
7 years ago
ca7d36d9ed
RAMPS pins for ANET_KEYPAD_LCD
7 years ago
e0a6ee8da5
[2.0] Fix up G33, LPC1768 + SDCARD_SORT_ALPHA ( #8250 )
...
* Update Conditionals_post.h
* Add a cast to round() to convert to a unsigned int
Add's a cast to round() so that it will compile properly. round() returns a float which must be cast to a integer for the following % operation. Use a unsigned int as a negative index to an array is wrong. Should never be more than 255 points allowing us to use a 8 bit cast.
* Update G33.cpp
7 years ago
dac1f6fe74
Tweaks to cubic_b_spline code style
7 years ago
4df024d7b9
Merge pull request #8234 from thinkyhead/bf2_native_operation
...
[2.0.x] Operate in Native Machine Space
7 years ago
601ccded89
Fix case-insensitive config issue
7 years ago
f8393a0908
Operate in Native Machine Space
7 years ago
d83a9a53e8
Merge pull request #8220 from thinkyhead/bf2_serial_port_-1
...
[2.0] Add SERIAL_PORT -1 option for configurators
7 years ago
93ba72ea83
Add SERIAL_PORT -1, set on SBASE, STM32F103RET6
7 years ago
7e43dd1d23
Fix probes configuration url
...
Based on #8241 by @machaj
7 years ago
ca0e4b4e96
Some cleanup around 'lcd_bootscreen()' and 'lcd_kill_screen()'
...
Move 'lcd_bootscreen()' from `lcd_init()` to 'setup()' where it is cexecute exactly once. Saves 'bool show_bootscreen'.
Move the call of 'lcd_custom_bootscreen()' to the begin of 'lcd_bootscreen()'.
Move the delays into the related functions.
Move the picture loop around 'lcd_kill_screen()' into the function.
7 years ago
84b93d941f
Merge pull request #8178 from thinkyhead/bf2_config_tweak
...
[2.0.x] Faster menu navigation for Anet A8
7 years ago
70be4d206e
[2.0.x] UltiMachine Archim2 ( #8190 )
...
* UltiMachine Archim2 support
* SPI gets included by the library
* Invert TMC2130 diag pin state
* Clean up Archim2 pins
* Update Archim2 config
* FAN2 -> FAN1
* Cleanup
* Add brief Archim installation instructions
* Bring pins into compliance
* Update 1.0 SD Detect pin for 1.1
* Update Configuration.h
* Update pins_ARCHIM2.h
7 years ago
f3deb37bdf
Merge pull request #8236 from thinkyhead/bf2_protect_M303
...
[2.0.x] M303 thermal runaway protection
7 years ago
31f112cf58
Cleanup trailing whitespace
7 years ago
2f9e42feb9
M303 thermal runaway protection
7 years ago
e5ae545647
Remove ADCKey steps acceleration
7 years ago
6827e243a0
[2.0.x] G33 magic numbers ( #8171 )
...
* [2.0.x] G33 magic numbers
* oops
* Comments
* oops
* warning
* better comment section
* remarks
* extra grids
7 years ago
8735ae984b
Merge pull request #8227 from tcm0116/2.0.x-pin_mapping
...
LPC1768: updates to use the new pin_t typedef
7 years ago
c72a0610b4
Fix watchdog in WATCHDOG_RESET_MANUAL mode AVR
7 years ago
13d839795c
LPC1768: updates to use the new pin_t typedef
7 years ago
eb13b8d985
Add MKS Gen L board
7 years ago
063e957fc4
Update pins_MKS_SBASE.h ( #8188 )
...
* Update pins_MKS_SBASE.h
Deleted E_MUX2, not used.
Changed #define LCD_PINS_D4 P0_14 // EXP1.5 to #define LCD_PINS_D4 P0_15 // EXP1.5, wrong in MKS's pinout schematic.
Swapped TEMP_BED_PIN and TEMP_0_PIN port's, request from user, more logical...
* Update pins_MKS_SBASE.h
Moved MUX signals to J8 and re added MUX2, cleaner wiring..
7 years ago
f7133e53fd
Fix case light off
...
Addressing #8205
7 years ago
0108d5181f
Allow asterisks in G-Code commands
...
Addressing #6655
7 years ago
34745b2183
Organize boards.h by architecture
7 years ago
9cc1d8e312
[2.0.x] Support for SilverGate Board
7 years ago
03e5369411
Faster menu navigation for Anet A8
...
Addressing #8166
7 years ago
f1edf83720
Merge pull request #8187 from rafaljot/patch-5
...
Update InterruptVectors_Due.cpp
7 years ago
b2bd77c40a
Merge pull request #8191 from thinkyhead/bf2_rearm_more
...
[2.0.x] Add SDCARD_SORT_ALPHA options for LPC1768
7 years ago
571ced712d
Add SDCARD_SORT_ALPHA options for LPC1768
7 years ago
778e4e4c23
Update InterruptVectors_Due.cpp
...
const pfnISR_Handler *isrtab = get_relocated_table_addr();
What compiler do you use? Arduino 1.8.5 can't compile this "const".
7 years ago
cae8703e0d
Merge pull request #8181 from thinkyhead/bf2_fix_bootscreen_repeat
...
[2.0.x] Only show custom bootscreen once
7 years ago
a516856df9
Only show custom bootscreen once
7 years ago
727a403ba1
[2.0.x] Fix NO_MOTION_BEFORE_HOMING unwanted behaviour ( #8176 )
...
* [2.0.x] Fix NO_MOTION_BEFORE_HOMING unwanted behaviour
NO_MOTION_BEFORE_HOMING should prevent XYZ movements only when homing is not done.
E axes should be allowed
* Update G0_G1.cpp
* Update G0_G1.cpp
7 years ago
577659cacf
Basic support for Azteeg_X5_GT ( #8139 )
...
* Basic support for Azteeg_X5_GT
Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
* Add fan pins for AZTEEG X5 GT
Signed-off-by: Alexey Shvetsov <alexxy@gentoo.org>
* Fix endstop pins
* Add servo0 pin
7 years ago
0b02f9cc33
Merge pull request #8168 from thinkyhead/bf2_config_tweak
...
[2.0.x] Apply Re-ARM SPI review items
7 years ago
04c0d9f3c3
Implement kinematic software endstops
7 years ago
9f89b5d876
Fix for MAX_VFAT_ENTRIES sanity check
7 years ago
2cdde08339
Apply items specified in code review
...
Followup to #8122
7 years ago
34be5d33c0
The plural of 'axis' is 'axes'
7 years ago
6e5f13a5c2
Merge pull request #8122 from Bob-the-Kuhn/2.0.x-restore-Re-ARM-RepRap-Discount-Full-Graphics-fix-(partial-solution)
...
2.0.x - Restore fix for garbaged display on Re-ARM with RepRap Full Graphics Smart Controller
7 years ago
b7a66742dd
tested
...
add sort alpha section to other LPC1768 boards
7 years ago
bbc2e66634
Fix AZSMZ MINI pins for new LPC1768 pinmapping
7 years ago
31e96935f7
Fix EXTRA_FAN_SPEED
...
Addressing #8158
7 years ago
c94dce6b32
Merge pull request #8113 from thinkyhead/bf2_fixup_sd_reprint
...
[2.0.x] Cleanup after SD Print Again, whitespace, tabs
7 years ago
ce1c9c0808
Tweak QUICK_HOME description
7 years ago
12458cefc4
Remove 5s timer hack. Encoder pos is saved on print start!
7 years ago
9a4cf11835
Remove return_to_status_ms hack, just use defer...
7 years ago
8949c8c0a5
Move SD_REPRINT_LAST_SELECTED_FILE to ultralcd.cpp
7 years ago
817175613a
Merge pull request #8157 from thinkyhead/bf2_anet_10_servo
...
[2.0.x] Define a default SERVO0_PIN for Anet 1.0
7 years ago
723f2a77f6
Implement support for Dual X and Y endstops
7 years ago
e04425281d
Add Dual Steppers / Endstops to configs
7 years ago
edff2c917b
Cleanup for DIGIPOTS settings
7 years ago
3e8754a38a
Add/correct time units on planner vars / M205 B
7 years ago
b2a48f1a04
Provide a SERVO0_PIN for non-standard LCD
7 years ago
b232f39341
AVR: Hidden option to use 8s watchdog
7 years ago
9d4cfd2013
Merge pull request #8142 from thinkyhead/bf2_fix_m303
...
[2.0.x] Fix M303 thermal protection
7 years ago
eae0aea1e0
Fix M303 thermal protection
7 years ago
a1a4fc277e
(2.0.x) serious bug G33 ( #8136 )
...
* (2.0.x) serious bug G33
* Revert config changes
This reverts commit 74b5a98223b7b7fb970d05b8541f4a079c3cfe56.
7 years ago
325233b454
Fix automatic stepper assignment for X/Y/Z dual stepper drivers ( #8130 )
7 years ago
50b4f9cbf7
LPC1768 Pin Mapping and M43 cleanup ( #8119 )
...
* LPC1768 M43 cleanup
* Update pinmapping.h to #define pins
7 years ago
6b1d1a818b
Revert default BABYSTEP_MULTIPLICATOR to 1
7 years ago
ba8dc678f5
Arduino Due XON/XOFF implementation
...
Alos includes emergency parser and configurable TX/RX buffers for Arduino Due.
7 years ago
8d9c3cc2b7
Add a module for Due SRAM-based Interrupt Vector Table
...
This is the ONLY way to be able to override ISRs stolen by the Arduino Runtime, such as Serial or USB device interrupts. This feature is needed so Arduino modules can be replaced and enhanced.
7 years ago
c9bbef6380
Cosmetic fix for HAL_AVR/MarlinSerial.cpp
...
Instead of using const char, it is better to use uint8_t
7 years ago
dcfc2503c2
G33 Autotune calibration update #10
7 years ago
b338cafc65
Merge pull request #8111 from thinkyhead/bf2_fwretract_fix_oct26
...
[2.0.x] Improved Firmware Retraction logic
7 years ago
ada90f7335
Clean up trailing spaces
7 years ago
7fad26549b
Concise SD_REPRINT_LAST_SELECTED_FILE description
7 years ago
33f379fe88
Add some Polish language
...
Thanks @SCiunczyk
7 years ago
daeff5a11a
Tweak neopixel self-test
7 years ago
0ceec1f166
Fix leveling_active_at_z warning
7 years ago
eb02f8c719
Improve FWRETRACT logic, add common sense
7 years ago
bd78ca0ee3
Add M290 Babystepping
7 years ago
ce5f0ec85a
Bring STM32 example config up to date
7 years ago
46e9eae159
Tweak to M100 config comment
7 years ago
c45514f811
Merge pull request #8094 from thinkyhead/bf2_neopixel_led_parity
...
[2.0.x] Bring NEOPIXEL_LED into parity with 1.1.x
7 years ago
229a27a1c7
save FLASH by using reduced font for some languages
7 years ago
3f5f39576b
Reprint option for last SD Memory card file ( #8106 )
...
* Re-Print of same SD Memory Card file with single click
* Re-Print of same SD Memory Card file with single click
* This is the bugfix-v2.0.0 version of https://github.com/MarlinFirmware/Marlin/pull/8104
7 years ago
9e699811d2
Make LPC1768 pinmapping not specific to Re-ARM ( #8063 )
...
* Merging early because of build failures. See #8105
* Make LPC1768 pinmapping not specific to Re-ARM
* Add HAL_PIN_TYPE and LPC1768 pin features
* M43 Updates
* Move pin map into pinsDebug_LPC1768.h
* Incorporate comments and M226
* Fix persistent store compilation issues
* Update pin features
* Update MKS SBASE pins
* Use native LPC1768 pin numbers in M42, M43, and M226
7 years ago
3ac581eac9
Neopixel changes for parity with 1.1.x
7 years ago
7b3098bbd5
Add AZSMZ Mini ( #8005 )
...
* Add AZSMZ Mini
* Remove tabs, adjust spacing
* Renumber boards to group by family
* Patch up spacing
* Tweak
7 years ago
e00ed10c4c
GT2560 config MKS_MINI_12864 => SDSUPPORT
7 years ago
10a5e4d80f
Merge pull request #8078 from thinkyhead/bf2_mks_mini_lcd
...
[2.0.x] Add MKS MINI 12864 support to GT2560
7 years ago
Scott Lahteine