3a3d358df9
Fix Printrboard with LCD (redo)
...
Based on #2860 - rebased for RCBugFix
9 years ago
eb85342fd9
Merge pull request #2989 from AnHardt/fix2661
...
Pre home display - Stepper release
9 years ago
14f3ca1b2e
Merge pull request #2978 from thinkyhead/tool_offset_abl_rcbugfix
...
Apply bed leveling matrix when switching extruders
9 years ago
91fcdc2b99
Merge pull request #3090 from thinkyhead/rc_spelling
...
Various minor spelling corrections
9 years ago
772460a7b8
Various minor spelling corrections
...
Redo of #2939 rebased against RCBugFix
9 years ago
0fb507a75d
correct raise_z_for_servo
9 years ago
04a0d45c22
Merge pull request #2821 from MarlinFirmware/ReinitializeDisplay
...
Fix status LEDs update when reinitializing the display
9 years ago
b4e5e0f11d
Add Watchdog reset in kill()
...
Add watchdog reset in the kill loop to simplify recovering.
9 years ago
547d35a921
Merge pull request #3067 from Blue-Marlin/ALARM_PIN
...
Remove unused ALARM_PIN
9 years ago
79778d46d9
Merge pull request #3066 from Blue-Marlin/Fix-disable_all_heaters()
...
Fix disable_all_heaters() for MAX6675
9 years ago
a68228bf55
Remove unused ALARM_PIN
...
Remove unused ALARM_PIN from all the Configuration.h's
9 years ago
9eb4aceee4
Merge pull request #2986 from thinkyhead/enable_watchdog
...
Enable USE_WATCHDOG by default
9 years ago
0631541166
Fix disable_all_heaters() for MAX6675
9 years ago
222d13d5ed
Merge pull request #3051 from thinkyhead/rcbugfix_dual_axis_offset
...
Code cleanup in gcode_T
9 years ago
186629aee8
Merge pull request #3057 from jbrazio/3034-z_raise_after_probing_fix
...
Fix Z_RAISE_AFTER_PROBING for non DELTA printers
9 years ago
a42fb35c56
Merge pull request #3050 from Blue-Marlin/fix-1166
...
Temporary workaround for stack overflow
9 years ago
67e15aac3d
As pointed out by @Blue-Marlin the previous code would raise the Z axis
...
twice for a servo based probe.
9 years ago
17cc2a9663
Z_RAISE_AFTER_PROBING value was being ignored by Marlin because
...
raise_z_after_probing() was only called if the printer type was set to a
DELTA or if the printer had a docking sled for the probe.
9 years ago
252f4a75cd
Merge pull request #3043 from oxivanisher/RCBugFix
...
Example configuration for Kossel XL
9 years ago
fd1243c184
Merge pull request #3052 from thinkyhead/rc_fix_m145_eeprom_output
...
Fix "M145" output in M503 report
9 years ago
0bc648353f
Merge pull request #3031 from tnw513/RCBugFix
...
Fix board type for Hephestos: RAMPS 1.4
9 years ago
f27c2b6b4b
Reimplement #2892
...
Include #2892 to fix the isHeating symbol in the extruder graphics
9 years ago
615bec2329
Activate warning about possible reduced accuracy by default
...
Renamed `WARN_REDUCED_ACCURACY` to `DISABLE_REDUCED_ACCURACY_WARNING`
Changed the condition for blinking from
```
#if ENABLED(WARN_REDUCED_ACCURACY)
```
to
```
#if DISABLED(DISABLE_REDUCED_ACCURACY_WARNING)
```
9 years ago
1c889cd303
Refresh previous_cmd_ms during run_z_probe()
...
Refresh previous_cmd_ms during run_z_probe() to prevent:
stepper shutdown for expired DEFAULT_STEPPER_DEACTIVE_TIME
and extrudes for expired EXTRUDER_RUNOUT_SECONDS
(https://github.com/MarlinFirmware/MarlinDev/issues/238 )
9 years ago
4b02f33e69
Distribute config-changes to the other configurations
9 years ago
be24fdacea
The same changes to the axis-letters now for the char-displays
...
Exactly the same - copy/paste.
9 years ago
5b0f659355
Changes for graphics displays
...
Replaced displaying "---" instead of the value of a coordinate when
unhomed or with reduced precision
with blinking the coordinate-prefix-character ('X','Y','Z').
For "unhomed" a '?' is shown every second second - until that axis is
homed. The value displayed is, as before the "---" where displayed, the
relative to the reset position coordinate value.
When the axis stepper was disabled, now we can display a hint on that,
by showing a blinking ' ' instead of the axis letter, when
WARN_REDUCED_ACCURACY is defined.
I suppose the code itself is here the better documentation.
A '+/-' character is in non of our charsets so i decided for a '?' for
now to reduce the work.
There is no additional space on the displays one could use to display
the information, so replacing something is the only option. As the axis
letters are totally redundant with their positions on the display they
contain the least information.
So my decision was to overwrite them.
9 years ago
32ae9f9ab7
Fix stepper shutdown during waiting for temperatures
...
In the wait loops of M109 M190 idle() is called, what checks
stepper_inactive_time against previous_cmd_ms.
Because we can be several minutes inside the loop, resetting
previous_cmd_ms only outside the loop caused stepper shutdowns.
The name of previous_cmd_ms does not really reflect its use. It's set
not only when a new command was received or executed but also in many of
the movement routines. For that the little extension of using it during
the wait will (hopefully) not hurt.
# Conflicts:
# Marlin/Configuration_adv.h
9 years ago
b6e69e71ce
Make stepper shutdown after inactivity dependent
...
Make stepper shutdown after inactivity dependent on a new set of
#defines.
DISABLE_INACTIV_X
DISABLE_INACTIV_Y
DISABLE_INACTIV_Z
DISABLE_INACTIV_E
And make exemplaric Configuration.
Names can be discussed.
This makes the disabling of the steppers independent from the DISABLE_?
settings witch shut down the steppers immediately.
9 years ago
051325ccd7
Introduce axis_homed
...
Introduce additional variable axis_homed to replace axix_known_position
when the coordinate display should indicate the axis is not homed.
This is to distinguish between "not homed" and "inexact position possible
because stepper was disabled".
# Conflicts:
# Marlin/ultralcd_implementation_hitachi_HD44780.h
solved
9 years ago
e736779d7e
blink for char-lcds
...
Implement and test blinking for char-lcds
# Conflicts:
# Marlin/ultralcd_implementation_hitachi_HD44780.h
solved
9 years ago
7253a1971d
Fix "M145" output in M503 report
9 years ago
d118e3f985
Merge pull request #3044 from thinkyhead/rc_gcode_spaces
...
Fix GCode handling of spaces between command letter and first digit
9 years ago
100271e6ac
minor cleanup in gcode_T
9 years ago
fd9e94e5a4
Fix crashes when the Z axis is moved via LCD
...
Fix crashes when the Z axis is moved via LCD
by calling `plan_buffer_line` only when there is enough room in the
planner buffer, to avoid endless recursion.
A brief description about what went wrong is in #1166
9 years ago
8dccd5a7ea
Merge pull request #3018 from CONSULitAS/RCBugFix_K8200_backinsync
...
K8200: sample config back in sync
9 years ago
6a4f06d35d
Fix GCode handling of spaces between command letter and first digit
9 years ago
68eae2b5a8
added kossel xl example configuration
9 years ago
eb5817675d
Fix board type: RAMPS 1.4
9 years ago
cb88fdd242
Protect MarlinSerial against interrupts
...
Protect MarlinSerial against interrupts
by shielding the CRITICAL_SECTIONs
Now with a test if RX_BUFFER_SIZE is in the required range.
Code in peek() and read() is now optimized for readability and showing the similarity between the two.
Maybe a bit overprotected in checkRx() and store_char(), but now some days without detected errors from this source.
9 years ago
dc0f41868e
Make rx tail/head atomic
9 years ago
ea8409ad5d
Fix: current_command_args contains command
...
@thinkyhead
Hi Scott,
your code from a0f362c@thinkyhead is great, but you forgot to skip the
command.
Symptom `M117 Test`shows `M117 Test` on LCD instead of `Test`.
see also
https://github.com/MarlinFirmware/Marlin/commit/a0f362c735401ebbcd95de3f
6f8e3c2f17ecc770 lines 941, 2851 and so on
Greetings and welcome back
Jochen
9 years ago
9a3408e58f
Merge pull request #3024 from thinkyhead/rc_remove_steps_mm_e
...
Remove obsolete STEPS_MM_E setting
9 years ago
1093c780c8
Remove obsolete STEPS_MM_E setting
9 years ago
a4fe6a45ae
K8200: sample config back in sync
...
* Configuration.h:
* updated header comment
* new UUID feature used
* sync to default config
* typos fixed
* changes better documented
* reflect change in SDSUPPORT feature
* Configuration_adv.h
* updated header comment
* thermal protection tuned to work with K8200
* homing tuned
* sync to default config
* typos fixed
* changes better documented
* reflect change in LCD features
* use long filenames
* use Watchdog
* use Babystepping
* use Auto Filament Change
9 years ago
c2e5c6c12c
Nest Manual Bed Leveling options
...
This formalizes the dependency of MANUAL_BED_LEVELING on
MESH_BED_LEVELING
9 years ago
042a6a0a37
Extend existing MESH_BED_LEVELING test
9 years ago
08b3147791
sanity check for MANUAL_BED_LEVELING
9 years ago
9f8e6dce20
Merge pull request #2942 from esenapaj/esenapaj-patch-2
...
more suitable display format for delta printer
9 years ago
e1beaf61eb
Merge pull request #2985 from AnHardt/adv-ok
...
Repair N in ADVANCED_OK
9 years ago
34cde1b77c
Merge pull request #14 from MarlinFirmware/RCBugFix
...
Rc bug fix
9 years ago
f00ca3fd89
Fix layout descr. in configuration_store.cpp
9 years ago
0c9db67273
Merge pull request #2983 from AnHardt/ok-echo
...
Replace the "ok" in M280, M301, M304, M851 with output not including …
9 years ago
fbfbc5e330
Enable USE_WATCHDOG by default
9 years ago
d4e7c2d694
Merge pull request #2976 from thinkyhead/drop_configurator
...
Drop the experimental Configurator
9 years ago
9df0e0e0cc
Merge pull request #2974 from thinkyhead/sanitycheck_spi_speed
...
Sanity-check deprecated options replaced by SPI_SPEED
9 years ago
3e2473e695
Merge pull request #2988 from thinkyhead/z2_more_extruders
...
Use next open E connector for Y2/Z2
9 years ago
8eaba020fb
Merge pull request #2973 from thinkyhead/fix_splash_url
...
Remove references to marlinfirmware.org
9 years ago
438a87eba8
Sanity check deprecated SDSLOW, SDEXTRASLOW
9 years ago
b19b272172
Update configurations with SPI_SPEED
...
- Include aligned comment about new SDSUPPORT behavior
9 years ago
7f30f85602
Merge pull request #2987 from thinkyhead/gcode_allow_no_initial_space
...
Fix handling of spaces in GCode
9 years ago
b81d3b83cf
Drop the experimental Configurator
...
Development moved to https://github.com/thinkyhead/MarlinConfigurator
9 years ago
be691b51f1
Remove references to marlinfirmware.org
...
The domain is gone and doesn’t redirect, so for now show no URL on the boot screen.
9 years ago
f3f58bd619
Merge pull request #2992 from thinkyhead/rc_rename_fpos_t
...
Rename fpos_t to avoid libc conflict
9 years ago
83ffc9eb4f
Show raw steps in M114
...
This is a proposed change. This section of M114 output is a debug
extension according to RepRap wiki.
9 years ago
373e8a1ad4
Fixes for COREXY and COREXZ coordinates
9 years ago
31656e68bc
Fix for homing X and Y before raising Z when Z_SAFE_HOMING is set.
9 years ago
8ea55323d8
Fix for not raising Z before homing X and Y
9 years ago
b83e472bd3
Rename fpos_t to avoid libc conflict
9 years ago
68457ee903
For Dual Y/Z use the next available extruder pins
9 years ago
711e5db19a
Tweak comment in process_next_command
9 years ago
400e9329be
Allow spaces after a code letter
9 years ago
cdcb80f3c5
Allow no-space after initial command
...
Addresses issue #2715
9 years ago
6f473f7fc6
Repair N in ADVANCED_OK
...
Send the correct line number.
If no N was in the command - non't send an N.
9 years ago
efbd705eda
Replace the "ok" in M280, M301, M304, M851 with output not including an "ok"
...
Replace the "ok" in M280, M301, M304, M851 with output not including an "ok"
to avoid senting two "ok"s for a single g-code.
Doing the same for M105 would break the input filters of the hosts.
For M105 the other "ok" is omitted.
9 years ago
8e66028d25
Apply the ABL rotation matrix to the extruder offset.
9 years ago
ab5aa3fc92
Merge pull request #5 from MarlinFirmware/RCBugFix
...
Rc bug fix
9 years ago
27d918d836
Merge pull request #4 from MarlinFirmware/RCBugFix
...
Rc bug fix
9 years ago
159ff94afd
Remove obsolete HEATER_BED_DUTY_CYCLE_DIVIDER #2977
9 years ago
1270fbfd38
Using SET_INPUT instead of pinMode
9 years ago
b58083b0fa
Getting rid of SDEXTRASLOW, SDSLOW variables.
9 years ago
1833049b8a
reusing millis()
9 years ago
1b7c443628
Adding SDULTRASLOW variable.
...
Instead of changing SDEXTRASLOW variable to a slower speed, the new
SDULTRASLOW is used for rigidbot panel.
9 years ago
6f9e9c0e4f
Cleaning up, getting rid of the fake encoder count variable.
9 years ago
becbfe1065
Fixing Rigidbot LCD Panel Support
9 years ago
4882a7eded
more suitable display format for delta printer
9 years ago
d7272e3f36
Merge pull request #3 from MarlinFirmware/RCBugFix
...
Rc bug fix
9 years ago
62bad1b60f
Merge pull request #2848 from japzi/RCBugFix
...
Fixing Rigidbot LCD Panel Support
9 years ago
59d345a3dd
Update Configuration.h
9 years ago
b8f0c8a4c7
Update Configuration.h
9 years ago
df0d599c79
Update Configuration.h
9 years ago
a366697649
Update Configuration.h
9 years ago
7c94c83765
Repair formula mangled by PR#1319 in Jan 2015
9 years ago
2932602643
Update stepper.cpp
...
Forgot Z2_MIN_PIN
9 years ago
06555febdd
Using SET_INPUT instead of pinMode
9 years ago
8d2aa2368d
Update Configuration_adv.h
9 years ago
0de5fcad0a
Update Configuration_adv.h
9 years ago
1403b9acc0
Update Configuration_adv.h
9 years ago
5cf1c38ea1
Update Configuration_adv.h
9 years ago
04ab61bf40
Update Configuration_adv.h
9 years ago
39c62fbd6f
Update Configuration_adv.h
9 years ago
efcb769003
Update Configuration_adv.h
9 years ago
992fbb831d
Update Configuration_adv.h
9 years ago
5ee6fe6385
Update Configuration_adv.h
9 years ago
056daf00fc
Update Configuration_adv.h
9 years ago
71aafb79a0
Update Configuration_adv.h
9 years ago
2c9e0415c7
Getting rid of SDEXTRASLOW, SDSLOW variables.
9 years ago
a64bcd53e9
reusing millis()
9 years ago
e6cc232184
Adding SDULTRASLOW variable.
...
Instead of changing SDEXTRASLOW variable to a slower speed, the new
SDULTRASLOW is used for rigidbot panel.
9 years ago
83c4131ba3
Cleaning up, getting rid of the fake encoder count variable.
9 years ago
5eeea2f611
Fixing Rigidbot LCD Panel Support
9 years ago
f6950acb8e
Residual unused variable — Backport
9 years ago
7a670e3911
Improve planner & stepper PR #263
9 years ago
58658c9279
Call the probe pin a probe pin and not a min endstop
9 years ago
0fa3bac8ee
If unused, just don’t define it.
9 years ago
3b2973da6a
Prepare Ramps for user redefinition
9 years ago
1635613c25
Backport cosmetic
9 years ago
0b429461d5
Back port Cosmetic changes
9 years ago
0cebe85e65
Clean up spacing and duplicate entries
...
• Removing trailing whitespace
• Adjusting indention for better readability
• Removing duplicated entries
9 years ago
e7b40bbe98
Change link to U8glib source
9 years ago
e2da2b4105
Back port language translation
9 years ago
4f314afaf0
Allow Thermistor #12 to be used on hotends also
...
//100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
Caveat Emptor —-
I’m not sure that this really makes sense,
but why keep someone from using it?
9 years ago
60d5658da8
Revert nozzle_bed_fan_menu_items
...
For some reason that I cannot determine, using a sub-function causes
the Tune sub-menu to act strangely, yet replacing the function call
with its code content works perfectly.
9 years ago
57da1b8497
Host parseble output for M109, M190 and M303
...
Make the output of M105 more similar to Repetier.
Make the text-print pert of M105 an extra function to make it reusable. `print_heaterstates()`
Use `print_heaterstates()` in M019, M190 and M303
9 years ago
fcceb98191
Unglobalize no_wait_for_cooling
9 years ago
78a347a01a
change nx, ny, nz and ne from float to long
...
st_set_position takes long
```void st_set_position(const long& x, const long& y, const long& z, const long& e)```
9 years ago
6d691aceee
change dx, dy, dz and de from float to long
...
anything is long, we don't need float there
9 years ago
6bfcb74c25
The probe stowing coordinates have changed
9 years ago
0fbfb22506
Renaming delta speeds (PR2824)
...
dx -> dsx
dy -> dsy
dz -> dsz
de -> dse
9 years ago
8d1eeff021
Fix status LEDs update when reinitializing the display
...
Fix status LEDs update when reinitializing the display
By using the regular update function during init.
Fixing #2683
9 years ago
5a54204f72
Marlin 1.1.0 Release Candidate 3 - 01 December 2015
9 years ago
bb4efcf603
Handle temp callbacks when THERMAL_PROTECTION_HOTENDS is not defined
...
by alternate definition for the callback macros
9 years ago
96d0d04b8f
Update LCD buttons less frequently
...
Move slow_buttons_update into the LCD_UPDATE_INTERVAL block
lcd_implementation_read_slow_buttons() will then be executed ~10 times a
second.
9 years ago
e293ea57f0
Unbalanced brackets in setPwmFrequency
...
This is a back port of the correct in issue #248
9 years ago
c956b52c4a
Babystep Multiplier
...
Analog to https://github.com/MarlinFirmware/MarlinDev/pull/250 by
@RicardoGA
Restore the Babystep Multiplicator functionality and now it's available
for X/Y/Z
9 years ago
956418c674
Kc is also a multi-PID parameter
9 years ago
33addc52a1
Suppress Z_MIN_PROBE_REPEATABILITY_TEST for DELTA and SCARA configurations (PR#2747)
...
For now Z_MIN_PROBE_REPEATABILITY_TEST is not possible for DELTA or SCARA
configurations.
This PR comments the feature out, where it is commented in by default.
9 years ago
8da2e98985
Split RAMPS 1.3 an 1.4 (PR#2741)
...
because of hardware differences on the SERVO0_PIN
9 years ago
be7167ed97
Change XY formatting on LCD (PR#2740)
...
According to #123 negative values for XY at or below -100 are displaying incorrectly, dropping the first digit. Deltas can easily have XY values in this range. This PR adds a function to display floats/ints formatted like `_123`, `-123`, `_-12`, or `__-1` as appropriate and applies it to the XY coordinates on Hitachi displays. It also moves the Z value to the right to be consistent with the XY formatting.
9 years ago
e7099ea597
Fix Portuguese (Portugal) strings (PR#2700)
...
Align strings with release
9 years ago
754b13d8fe
Patch issue #2315
9 years ago
dbd4c17096
Init Kp, Ki, Kd to 0
9 years ago
644c376e84
Use binary OR with endstop bits
9 years ago
54a39d8c1a
Use a ternary in qr_solve.cpp
9 years ago
17c23bbaf3
Shorten gcode_M221 yet function the same
9 years ago
c0e791dbe9
Only look for "N" line number as first parameter
9 years ago
b4af4441c5
Clean up watchdog impl.
9 years ago
8f16563bbd
Use "defined" with LCD_PIN_BL and LCD_PIN_RESET
9 years ago
6fa7e24af3
Use "UNUSED" to squash compiler warnings
9 years ago
d5b7c595ae
Use static locals in utf_mapper.h
9 years ago
9bdab4f3a8
Clean up "else" and other spacing
9 years ago
9b23490f01
Clean up spacing in configs
9 years ago
c6c37abd41
Update language_kana.h
9 years ago
c24045475a
Update language_kana_utf8.h
9 years ago
25d636c9e0
Compiler issues (PR#2696)
9 years ago
47401ec97b
MSG_EXTRUDER_SWITCHED_OFF was renamed to MSG_REDUNDANCY
...
in language.h, but was not renamed here. If TEMP_SENSOR_1 is enabled as redundant then
an error is thrown that MSG_EXTRUDER_SWITCHED_OFF is not defined.
Originaly by @12dstring
9 years ago
ba6a243197
DEBUG message has no parameter (PR#2671)
9 years ago
0c7f7ebcfb
Styling adjustments (PR#2668 & PR#2670)
...
Keep "astyled" reformatting
9 years ago
b5fb7075b9
Galician (gl) language.
9 years ago
7b4bdc0203
DUAL_X_CARRIAGE motor enabling
...
As noted by @darkjavi et.al. in #103 , the E1 motor was not being enabled in planner.cpp when using DUAL_X_CARRIAGE. This patch enables and disables E1 as it should.
9 years ago
91b5156b3e
Marlin 1.1.0 Release Candidate 2 - 29 September 2015
9 years ago
03f0edb57e
Fix high LCD status screen update frequency (PR#2655)
9 years ago
0ad25c6665
Hint for changed behaviour of SDSUPPORT
9 years ago
e01f5e1ef7
Cleanup
9 years ago
5e36b64635
SDEXTRASLOW for some SD card readers (PR#176)
...
Add SDEXTRASLOW which runs the SD card at SPI_QUARTER_SPEED. Quarter speed is needed for RIGIDBOT_PANEL
9 years ago
5d65a36dee
Give lcd_sd_status an UNKNOWN state (PR#180)
9 years ago
0f149ea0c6
LCD home button causes repeated homing (PR#175)
...
Fix: increased debounce delay.
9 years ago
b825567e0f
Drop www. from marlinfirmware.org (PR#175)
9 years ago
db27e67580
Apply PID_ADD_EXTRUSION_RATE to extras
9 years ago
bc50db9cf6
Implement PID_ADD_EXTRUSION_RATE
9 years ago
cffb2d457e
Cleanup file formatting
9 years ago
7ac7ddbf20
Show nozzles, heaters, and extruders numbered 1-4
9 years ago
5bc480fee8
Fix Move E menu items
9 years ago
fc882c34a3
Init lcd_sd_status as false to force lcd_update test
...
Replaces #145 which is way out of date
9 years ago
e27dd5c22d
Conditionalize functions that rely on SDSUPPORT
9 years ago
fabf3ae4a0
Add final Z raise after Delta probe
9 years ago
8c768a76a2
Create language_cz.h
...
Czech language translation.
9 years ago
5b9010965d
Update language.h
...
Added comment for Czech language (associated with file language_cz.h).
9 years ago
89fb778684
Fix up probe pin define and test
9 years ago
558665cd90
Constrain Tune > Nozzle/Flow menu items
9 years ago
9f462f0cf5
Hack to address stuttering caused by ISR not finishing in time
...
(PR #138 )
When the ISR does not finish in time, the timer will
wrap in the computation of the next interrupt time.
This hack replaces the correct (past) time with a time not far in the future.
9 years ago
8b3d63c423
Unify Delta XYZ homing rates
...
As noted in #130 allen key probe stow rate is based on homing rates,
but homing rates were left out of most delta configs. This unifies the
XYZ homing rates and applies the unified rates to allen key movements.
9 years ago
7c72b57313
Unify manual feedrate and Fix LCD MANUAL_FEEDRATE (PR#128)
...
As noted by @o-lampe at https://github.com/MarlinFirmware/MarlinDev/issues/114#issuecomment-136757614 the `MANUAL_FEEDRATE` for Delta Z should be the same as XY.
9 years ago
f690b82343
Remove extra MAX_FREQ_TIME define (PR#148)
9 years ago
a4c78ae786
Add E1 pins to SENSITIVE_PINS for Dual Y or Dual Z
9 years ago
a39fadf876
Update kossel-pro example config (again?)
9 years ago
34e0a8d848
Move Y2 and Z2 pins defines to pins.h
9 years ago
28599c51c7
Wrap Dual Y options in a conditional
9 years ago
11a065c0ca
Remove Z2 pins overrides from Configuration_adv.h
9 years ago
f7f6b5faae
Fix lcd_move_e compile error (PR#143)
...
Fix a compile error introduced in #98
9 years ago
2b30e8ac99
Conditionals for ULTIPANEL without SDSUPPORT
9 years ago
7c7a4051fe
Disable SDSUPPORT by default
...
As noted in #133 you can’t disable `SDSUPPORT` with `MAKRPANEL`,
`PANEL_ONE`, `MINIPANEL`, or `ULTIPANEL`. This patch makes it possible
to disable `SDSUPPORT` on these controllers and then disables it by
default.
Users of these controllers will now need to enable `SDSUPPORT` in their
configurations as others currently do.
9 years ago
b23d765991
Added Extrude From Multiple Extruders from LCD feature
9 years ago
8347a9d6e4
Fix HOMING_BUMP_DIVISOR for deltas configuration
...
* Re-bump speed divisor should be the same for delta printer.
9 years ago
703df2cb6c
Fix error message for probe region sanity check
9 years ago
4c8330c15c
Trim Adjustments for Delta Configurations
9 years ago
962120d1d2
Fix spacing in some conditional blocks
9 years ago
20b4772155
Create DEBUG_LEVELING_FEATURE
9 years ago
194f98ff95
Debug messages for homing and leveling
9 years ago
6292d9e815
Rename ENABLE_AUTO_BED_LEVELING
...
With the introduction of the #if ENABLED(…)
reads better than
9 years ago
91fd66ffba
add Lulzbot TAZ4 example configuration (PR#104)
9 years ago
7a275773ee
remove colon in utf_mapper.h (PR#106)
9 years ago
6b4b6fa315
update for newest version of U8glib_Arduino
9 years ago
9897a9147c
Update ABL comments (PR#95)
...
* Updates the auto bed leveling comments ONLY.
* Renames "Z probe" word usage in //comments and #errors properly.
9 years ago
a7822e3ff7
Some renaming of Z_PROBE to Z_MIN_PROBE (PR#91)
...
* Fix a couple of renames omission and macro expansion errors.
9 years ago
ad90e851b3
Use a small unsigned integer type
9 years ago
29b456ae07
Suppress some compiler warnings
9 years ago
23d742bf06
Don't free the stack array plane_equation_coefficients (PR#83)
9 years ago
e3b1e08777
Patch G30 to use raise_z_for_servo (PR#73)
9 years ago
a1eb90d5c0
Save another 30 bytes in gcode_SET_Z_PROBE_OFFSET
9 years ago
91122277f4
Reduce gcode_SET_Z_PROBE_OFFSET by 88 bytes
9 years ago
5707a2c3d5
indexindexIntoAB is only vald for !DELTA
9 years ago
d8860f9ad9
Alway end at the same point
...
Always end at [RIGHT_PROBE_BED_POSITION, BACK_PROBE_BED_POSITION]
Regardles the evennes of auto_bed_leveling_grid_points.
9 years ago
4ca8f4a9a7
Always zigzag
...
Use the shortest way between probing-points.
9 years ago
3d23424121
Add array indexIntoAB[xx][yy]
...
and use it.
9 years ago
e2d69f66b2
Make Z_PROBE a Z_MIN_PROBE (PR#65)
...
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.
Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX check for the probe in update_endstops().
Using an delta related idea of @clefranc from #61 ,
extended to the general change for all setups.
Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
9 years ago
6a6e863a47
Resolve #2581 by adding a missed ';' (PR#67)
9 years ago
e09ff79635
Update pins_RAMPS_13.h (PR#64)
...
Now all ramps configuration can enable Filament sensor not only EEB
9 years ago
e6aed7bb4e
Update thermistortables for Hisens Thermistor (PR#2588)
9 years ago
9d8cc24abf
Continue from the line following the M999 (PR#60)
...
If the printer is going to accept the M999,
then it should continue from that line number.
9 years ago
f3ab1dba54
Z babystepping for coreXY (PR#47)
...
only X and Y were not implemented
9 years ago
35afea1c0e
Restore test
...
PR#2572 Changed this because of faulty Boolean Logic
NOT(A OR (NOT B) OR (NOT C)) !=
(NOT A) AND ((NOT B) OR C))
Besides, the compiler should be smart enough to
optimize this without help from the programmer
9 years ago
6af75f4b5d
Squish down deprecated tests in sanity check
9 years ago
edeb58288e
Use PIN_EXISTS in sanity check
9 years ago
c30b7693e0
Clean up RUMBA pins conditions
9 years ago
46453905d6
Apply remaining ENABLED/DISABLED conditionals
9 years ago
b227d8c128
Supply a VERSION in a short form for displays
...
The long descriptor will still be available in M115
9 years ago
cd7828a928
This will be the 1.1.0 Release rather than 1.0.3
9 years ago
4e2f5618c1
Pick up Default_version when needed
9 years ago
329acc852e
Canonize Option flag USE_AUTOMATIC_VERSION
9 years ago
5a11d32a85
Move deprecation test to SanityCheck.h
9 years ago
7bb7a52940
Bring config up-to-date
9 years ago
244ea2014a
Boot-screen for text-displays improvements
...
Centred the logo for 16x4 and 20 x4.
Moved version to the bottom line
Code shrink to 704 bytes.
9 years ago
80f2a20842
Enable bootscreen in all Configurations
9 years ago
2684d061ed
Scroll too long strings on bootscreen
9 years ago
4f46df5dab
Make bootscreen configurable for the graphic displays
...
Saves about 473 byte of progmem and 28 bytes of RAM.
9 years ago
09571b7753
Boot-screen for the character displays
...
Uses about 488 byte of progmem and 32 byte of RAM.
For that configurable.
9 years ago
866efc14fe
Add Danish translations
9 years ago
267f3479d7
Adjust spacing in pins_RAMPS_13.h
9 years ago
56702e7bb9
Define servo pins just like other pins
9 years ago
4b9d5cd352
Use lowercase names for serial instances
9 years ago
1e2deff4fd
Rename BTENABLED to BLUETOOTH
...
- For some reason it’s easy to forget what BT stands for, but it
doesn’t need an abbreviation.
9 years ago
68055a5959
Include RIGIDBOT_PANEL in Conditionals
9 years ago
f8ed3a835d
Added comment with the RigidBot Big bed size
9 years ago
7deae6b6be
Updated RigidBot example configuration
...
- The default serial baud rate of 115200
- The regular RigitBot bed size 254mm/248mm/254mm
- Single stock extruder
- Stock termistors for extruder and hotbed
- Stock Min X/Y/Z stops. Max stops not connected
- Stock 32 teth tooleys (stock axis steps)
- No auto bed leveling
- No screen
9 years ago
5418faa1f9
Add sanity checks for old names
9 years ago
f03e063750
Rename BEEPER to BEEPER_PIN
...
For consistency with other pins, allowing use of `PIN_EXISTS` macro.
9 years ago
270c766de2
SDCARDDETECT -> SD_DETECT, added docs
...
- `SD_DETECT_PIN` replaces `SDCARDDETECT`
- `SD_DETECT_INVERTED` replaces `SDCARDDETECTINVERTED`
- Revise the description of `SD_DETECT_INVERTED`
- Add a note about the override of `SD_DETECT_INVERTED` in
`Conditionals.h`
9 years ago
496fc28dc3
Tweaks to pins comments
9 years ago
8d3b74cc6e
Rename SDCARDDETECT to SDCARDDETECT_PIN
...
- Rename the pin so it can be tested with `PIN_EXISTS`
- Fix some incorrect tests for `SDCARDDETECT`
9 years ago
0f5ada8cbd
Group the fail case in one negation (PR#2572)
9 years ago
7ddf1cda1d
Improve condition for SERVO_LEVELING (PR#2570)
9 years ago
f32048b8f5
In for a penny, in for a pound
9 years ago
e944f960de
Add a sanity check for old name "BEEPER"
9 years ago
8ebf0b92be
Spacing adjustments in some pins files
9 years ago
94a796c8cc
Rename BEEPER to BEEPER_PIN
...
For consistency with other pins, allowing use of `PIN_EXISTS` macro.
9 years ago
b217474eab
Compiler Complaints about concatenated tokens (PR#2566)
9 years ago
2460f82d8b
Make proper distinction between BEEPER and HAS_BUZZER
9 years ago
58cfcd4239
Overridable Options - Part 5
...
Apply `ENABLED` / `DISABLED` macros to files needing only a small
number of changes.
9 years ago
5e834352a9
Overridable Options - Part 11 (PR#2563)
...
Apply `ENABLED` / `DISABLED` macros to EEPROM-related files.
9 years ago
bf6eb93c61
Overridable Options - Part 10 (PR#2562)
...
Apply `ENABLED` / `DISABLED` macros to planner files.
9 years ago
51e89a269c
Overridable Options - Part 9 (PR#2561)
...
Apply `ENABLED` / `DISABLED` macros to temperature-related files.
9 years ago
c35fb88094
Overridable Options - Part 8 (PR#2560)
...
Apply `ENABLED` / `DISABLED` macros to stepper-related files.
9 years ago
0d8989fc14
Overridable Options - Part 7 (PR#2559)
...
Apply `ENABLED` / `DISABLED` macros to LCD-related files.
9 years ago
b4abb0ae7f
Apply ENABLED / DISABLED to Marlin core files (PR#2558)
9 years ago
c0d7ea3e7e
Overridable Options - Part 4 (PR#2556)
...
Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files.
9 years ago
4b40964064
Overridable Options - Part 3 (PR#2555)
...
Apply `ENABLED` / `DISABLED` macros to language-related files.
9 years ago
32683b282b
Include configurator copies of configs
9 years ago
37d1879386
Apply overridables to Configuration files
9 years ago
9d151bb61b
servo_endstop_angles -> servo_endstop_angle
9 years ago
9334479aeb
Minor cleanup of Conditionals.h
9 years ago
1f63293624
servo_endstops -> servo_endstop_id
9 years ago
edaaead7e0
Fix comment about SERVO_ENDSTOP_ANGLES
9 years ago
ed4a6371ad
Add HAS_SERVO_ENDSTOPS to simplify conditonals
9 years ago
70be61d416
Reset filament_size with a loop
9 years ago
ae9274be05
Fix minor compiler warnings in for loops
9 years ago
c7c8cfed6f
Complete M200 output with M503
...
- The contents of EEPROM include filament diameters even with
Volumetric disabled. This change makes `M503` display the full
volumetric settings so that playing back the output of `M503 S0` will
fully restore them.
9 years ago
4a58e447a1
Add array size to servo_endstop_angles (PR#2553)
9 years ago
a0ae9e30df
don't pass integer by reference, inefficient. (PR#2547)
9 years ago
d03f037a92
Get rid of malloc() and free() (PR#2549)
...
Just the minimal changes to qr_solve.cpp and .h to get rid of malloc() and free().
Saves about 656 bytes of progmem (library-code)
and 22 bytes for static variables.
Should use exactly the same amount of stack as it did before on the heap.
9 years ago
3b2b2313ff
Combine if block related to SERVO_ENDSTOPS
9 years ago
0af2a80e06
Make SERVO_ENDSTOP_ANGLES 2-dimensional
9 years ago
525d0dc239
Configurator is out-of-date AGAIN (PR#2550)
9 years ago
dd22cbbfb8
makefile: add buzzer.cpp (PR#2479)
9 years ago
9f48798ffd
Replace ENABLED with DEFINED for SERVO_ENDSTOPS (PR#2542)
9 years ago
ae00fad75b
Rename as M100
9 years ago
a401d738df
There is an echo in here
9 years ago
ed7d45e8f5
Memory watcher
9 years ago
d17f7ebc8a
Multiply WATCH_TEMP_PERIOD by 1000UL (PR#2535)
...
instead of 1000. Else we get errors with times over 32 seconds.
9 years ago
bea6739774
Don't include Z_RAISE_AFTER_PROBING if not used (PR#2527)
9 years ago
81bba7ed88
More sanity checking for extruder requirements (PR#2531)
9 years ago
87a97f3724
Fix conditions for display strings
9 years ago
aaccea0260
Shift some display only strings from language.h to lenguage_en.h
...
and translate them to German.
9 years ago
e4c01f1c7e
Simplify init with ARRAY_BY_EXTRUDERS1 macro (PR#2507)
9 years ago
ab6f1fdf8b
Move & document ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED (PR#2528)
...
As suggested in #2521
- Move `ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED` because `SDSUPPORT` is
also required.
- Add a note that endstops must be enabled for the feature to have any
effect
9 years ago
1183c10a2e
makefile: drop -q -q (much quiet) from avrdude flags
...
Annoying when trying to figure out if uploading
actually does something.
9 years ago
0e064357f4
makefile: use /etc/avrdude/avrdude.conf on linux
...
No need to look for arduino specific avrdude configuration
as distributions ship their own avrdude.conf file that
is compatible with arduino.
9 years ago
bcb7d5a149
Improve sanitycheck for TEMP_SENSOR_1
9 years ago
5b24f59401
Add sanity checks for temp sensors
9 years ago
fd0e81b0c7
Distinguish between BUZZER and SPEAKER (PR#2513)
...
A speaker needs a AC or a pulsed DC to make a sound, a buzzer only needs a DC.
A buzzer has it's own resonator. It works in most cases to feed the buzzer with a pulsed DC, but the sound will not be as loud as with pure DC.
There seem to be boards where the BEEPER-pin is not able to handle a PWM. Obviously intended for a buzzer.
To make these board able to handle a speaker
* replace the PWM based tone()-function again with a on-delay-off-delay loop.
Hopefully the last time I touch the beeper code.
9 years ago
e2957df05c
Shorthand for do_blocking_move_to
9 years ago
819c5b9b50
Adjust comment on Z adjustment
9 years ago
5a7356b6fc
Patch for G29 final Z position
...
Include all the necessary pieces to get the final Z position after
probing the bed, and add commentary about other possible changes.
9 years ago
088e09e052
Add forgotten Marlin_main.cpp
9 years ago
8b876241bd
Some more servo code tweaks
...
Just set up the pin. Don't move to a random position.
Simplify servo::move()
* servo::move() does not need the pin parameter - The pin is set during servo_init() with attach().
* servo::move() does not need a return value.
SERVO_LEVELING is the wrong condition to deactivate the servos.
Remove some temporary (Servo *) variables.
SanityCheck for the servo indexes.
9 years ago
b116c096bd
Reduce set_homing_bump_feedrate, save 42 bytes (PR#2512)
...
Updates to `set_homing_bump_feedrate`:
- Move the string into Program Memory, reduce length by 31 bytes
- Use an auto to get the divisor, adjust it on error
- Set feedrate once, at the end
9 years ago
f7e7862588
Better Sanguinololu & Graphical Controller (PR#2504)
...
- Change suggested at
https://github.com/MarlinFirmware/Marlin/issues/2482#issuecomment-123553
266
9 years ago
a1154d4a20
Enable Y and sanity-check CoreXZ (PR#2509)
9 years ago
932f1c109e
Move servos to the top in pins_MEGACONTROLLER.h
9 years ago
90f8ddfc1e
Apply MINIPANEL to other configs
9 years ago
00dbf69b6d
add MINIPANEL defines
9 years ago
8ac5e56934
fixed some format problems and cleaned code
9 years ago
eef595aa64
add makerlab mega controller pin configs
9 years ago
4e14e152fa
Add Travis tests for CORXY and COREXZ
9 years ago
27d7d2ccab
Correct bracketing for COREXY-XZ
9 years ago
469843427d
Reduce code in gcode_M81 (PR#2497)
9 years ago
c66955aaf9
Mark unchanging arrays as const (PR#2494)
...
The compiler may be able to optimize if it knows an array won’t be
changing.
9 years ago
278aa15301
Add COUNT macro and apply
9 years ago
d85861d296
Move macros, add ENABLED/DISABLED, add includes
9 years ago
17960fd2b0
Neaten up pins_MEGATRONICS.h (PR#2493)
9 years ago
aac2b9aa9d
Reduce code in gcode_M84 (PR#2492)
...
`gcode_M84` only needs to call `finishAndDisableSteppers`, which calls
all the other functions.
9 years ago
4971fa73f9
Add a sanitycheck error for old servo settings (PR#2491)
...
- Documentation solution for #2476
9 years ago
96ace72ddc
Servos attach/detach based only on servo config
...
Assuming #2470 fixed up the main issue.
9 years ago
b80a6a8d31
Correct Kossel Pro Configuration_adv (PR#2473)
9 years ago
000a6fce46
Extract update_endstops from stepper ISR (PR#2474)
9 years ago
e83eac312e
Move plan_arc next to prepare_move
9 years ago
5c5936508d
G2/G3 Arcs for Delta
...
- Update prepare_move_delta to take a target argument
- Add Delta support to plan_arc
9 years ago
9f53e2f0c9
Implement COREXZ in stepper.cpp and planner.cpp
9 years ago
fa00e1d97f
Explode conditions common to corexy and cartesian
9 years ago
c7dd5527b4
Add a C_AXIS and Z_HEAD to support COREXZ
9 years ago
129f986ccf
Add COREXZ option to configurations
9 years ago
69b0490b77
Show minimal preheat options in menus (PR#2471)
9 years ago
eacfe132aa
Change the name of servos[] and servo_t
9 years ago
3b23ccd366
Patch servos code for move
...
- Have `Servo::attach` explicitly return -1 if it fails
- Check for -1 in `Servo::move` because `servoIndex` might be 0
- Make `attach` / `detach` calls conditional on `SERVO_LEVELING`
- Move `SERVO_LEVELING` define to `Conditionals.h`
9 years ago
54ddc1d417
Simplify DRY RUN (PR#2358)
...
Elsewhere DRYRUN turns off the heating elements
and ignores constraints on them.
Here, whenever motion is entered into the planner,
if DRY RUN is set, we instantly act as if the E_AXIS
is in the desired final position.
9 years ago
944090c19c
Optimize lsDive logic
9 years ago
417706e578
Include space for the terminating nul in lsDive
9 years ago
f3c1a6b19c
Reduce lsDive stack usage to the minimum
9 years ago
fba4e6241b
Specify print format for reporting invalid tmp_extruder (PR#2465)
9 years ago
d15d869267
Rename axis_is_at_home() to set_axis_is_at_home() (PR#2464)
...
to make clear - it's not a question but an order.
9 years ago
f209b755a5
Move the Z probe as far as needed to trigger the switch (PR#2461)
9 years ago
0f1df62389
Fixup comments in code_seen
9 years ago
2945eb6650
Call code_seen only once per parameter
9 years ago
b742af2e2a
Move Y_STOP_PIN for Printrboard with SD (PR#2420)
9 years ago
baa9199973
Define extern delta only for delta
9 years ago
77e80ef367
Require extruders for thermal code
9 years ago
3bde4f4855
Require temp sensor for bed thermal protection
9 years ago
82a3ed2f9a
Cleanup and dev notes in Marlin.h
9 years ago
db23b9b184
Minor tweak to M204 code (PR#2457)
9 years ago
81d42406b7
Move braces in homeaxis to prevent a hanging else (PR#2451)
9 years ago
552a327df8
Fix lsDive filename stack overrun (PR#2449)
9 years ago
a6628f12cc
Eliminate the further use of the pin-parameter
9 years ago
8504992e9f
Remove the additional pin variable in Servo.cpp
...
as sugested by @c-born
inhttps://github.com/MarlinFirmware/Marlin/issues/1885#issuecomment-92618240
9 years ago
ed6598adf5
Corrected Bed Height vs. Bed Topology for verbosity > 3
...
and cleaned out some tabs.
Everything else is a rebased PR#2017 as proposed by @CptanPanic
9 years ago
62302ceb9e
Add calculation of difference between auto-correct bed level plane, and measured topo map.
9 years ago
de25a48dec
Remove PID examples from preconfigured configs
9 years ago
7456710a1f
Update configs formatting
9 years ago
391386dd94
Update configs for new servo deactivation
9 years ago
5243d8b523
Deactivate DEACTIVATE_SERVOS_AFTER_MOVE by default
9 years ago
49609f6c14
Activate the new servo.move() function
...
by replacing the sequences (attach, write, delay, detach), and their conditions with the new function in Marlin.main.cpp
and removing the old configuration in the ABL part of Configuration.h
9 years ago
40b6edcad7
Introduce DEACTIVATE_SERVOS_AFTER_MOVE in Configuration.h
...
DEACTIVATE_SERVOS_AFTER_MOVE is ought to replace PROBE_SERVO_DEACTIVATION_DELAY.
But it will work on all servo moves, not only the probe servo moves.
9 years ago
2ddb2a2be9
Add Servo::move() to servo.cpp
...
move(pin, angel) - Sequence of attach(pin), write(angel),
if DEACTIVATE_SERVOS_AFTER_MOVE is defined waits SERVO_DEACTIVATION_DELAY, than detaches.
As we have jitter on the servos during moves of the steppers, and detaching them improves this behaviour,
the usual sequence to handle a servo movement is:
attach(pin)
write(angel)
delay(until the servo finished the move)
detache()
Here a function to handle the complete sequence.
9 years ago
8a01e5fb7a
Update Russian translation (PR#2443)
...
Slightly updated translation.
9 years ago
e83575537a
Compiler defines USBCON for USB devices (PR#2433)
9 years ago
7268d46508
Always calculate extruder temperature PID d term (PR#2432)
9 years ago
87a872e103
Use st_get_position_mm where possible (PR#2411)
9 years ago
2e0da8abdc
Allow N to take a negative argument (PR@2402)
9 years ago
447dbd6fa5
Add STEPPER_RESET_PIN support
9 years ago
a0351bdb73
Remove STEPPER_RESET_FIX option
9 years ago
6b1b8cb2b3
Also nullify spaces before the checksum asterisk (PR#2409)
9 years ago
8e61314323
Use RIGIDBOT_PANEL for consistency with online docs
9 years ago
4b204da3c1
Cleanup of pins_RAMPS_13.h
9 years ago
536f86e896
RigidBot CONTROLLERFAN_PIN in Configuration_adv.h
9 years ago
f068e46661
RigidBoard include for pins.h
9 years ago
9ebcae496d
RIGIDBOARD / RIGIDPANEL
9 years ago
c3c605c658
Move note about LiquidTWI2 to Configuration.h (PR#2406)
9 years ago
4e9d658141
Prevent a hanging SERIAL_ECHO_START in M111
9 years ago
bc0fdbe88e
Use SERIAL_EOL in SERIAL_PROTOCOLLN macros
9 years ago
d78ebbc0e9
Remove unused MSG_OK_B and MSG_OK_T
9 years ago
6b494c1535
Use disable_all_heaters in M111
9 years ago
15190d40df
Add extra EOL after M111
9 years ago
0e1cf78f5c
Remove code for testing if probing range is too small (PR#2390)
...
becaue it is over-restrictive and superseeded by the now working tests
if the probe-recktangle can be reached. See iss#2366
9 years ago
d421f5250d
Correct the sign of zprobe_zoffset for G29 (PR#@391)
...
Sign flipped with #2167 .
See also comments
https://github.com/MarlinFirmware/Marlin/issues/2040#issuecomment-118568355
and following.
9 years ago
52fcc743ab
Replace "target" with "destination" in M600 (PR#2374)
...
- Also fix a bug in `M600` where `Z_MAX_ENDSTOP_INVERTING` is being
used as the index into the `destination[AxisEnum]` array.
10 years ago
a5033c3652
Enable LCD_PIN_RESET if it exists (PR#2375)
10 years ago
23c8c5348f
Z-height fix V2b (PR#2351)
...
here the other two occurences of `Z_PROBE_OFFSET_FROM_EXTRUDER` are
replaced with `zprobe_zoffset`.
10 years ago
a111fbbd0a
z-probe offset fix (PR#2361)
...
verified via 1.0.2 tag that compiles by multiple people,
credit for the fix goes to paulusjacobus for the initial find and
sniffle for the correction so M851 works.
10 years ago
42465ee444
Cleanup of comments & spacing
10 years ago
9682ed455e
Fix comment on M83, add comment to prepare_move
10 years ago
bb44fe17cf
Fix typo in buzzer.h endif (PR#2337)
10 years ago
36746143a1
Correct output of M48 (PR#2336)
...
n_samples is an uint8_t .
Got printouts like:
50 of 2 ...
10 years ago
f6ca5a8da8
Allow "M110 N123" without a checksum
10 years ago
aaad65ff5d
Include a comment documenting M110
10 years ago
862c72b030
Put the mandatory test of gcode_N first
10 years ago
30976f9773
Allow M110 to handle a second N argument
10 years ago
d135b15bb8
Init all endstop bits to 0 (PR#2332)
10 years ago
5ccb1c9e7d
Use millis for M600 audio feedback interval
10 years ago
fb16a83b8a
Cleanup M600 documentation comments
10 years ago
97ec224d72
Replace target with destination in M600
10 years ago
4ce9ddbb74
Check the temperature before filament change
10 years ago
Scott Lahteine