b7e938a9fb
LCD_BED_LEVELING enables a sub-menu for ABL
7 years ago
c87b0e21be
Add units to probe speed comments
7 years ago
05c33833e7
[2.0.x] Add NO_LCD_MENUS option ( #10582 )
7 years ago
9e07df5c1b
Extra options for LEVEL_BED_CORNERS ( #10483 )
7 years ago
a90cbc6339
[2.0.x] Wait for bed heaters between probing ( #10472 )
7 years ago
6c535081ec
[2.0.x] Add optional menu item to toggle software endstops ( #10389 )
7 years ago
c96412a78f
[2.0.x] UTF-8 language translation support ( #10213 )
7 years ago
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
7 years ago
dca69efc11
Update Bed PID comments
7 years ago
a29adde5c0
Implement BEZIER_JERK_CONTROL
...
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
7 years ago
0e8242180d
Chamber temperature monitoring and auto fan control.
...
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
7 years ago
adcb87f0db
Z Endstop Servo => Z Probe Servo
7 years ago
dd2949922b
Consolidate 3-point leveling point options
7 years ago
c6ff39cc14
Spacing cleanup
7 years ago
14c03cb6f4
[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) ( #10069 )
...
Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.
7 years ago
28f1276286
[2.0.x] Add Z_AFTER_PROBING option ( #10058 )
...
Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.
7 years ago
419d12ca1b
Add UNKNOWN_Z_NO_RAISE option
...
With this option enabled, Z won't ever be raised until after `G28` has been completed, and it won't raise if Z becomes unknown. This is good for machines whose beds fall when Z is powered off.
7 years ago
a2a672449a
Updated boot screen description
7 years ago
4953fb1c88
Standardize encoder defaults
7 years ago
5684beae90
Bring some configs up to speed
7 years ago
2024775e07
Spanish (UTF8) Language ( #9786 )
...
From #7314 by @MrAmericanMike
7 years ago
b2cf253a13
Add RESTORE_LEVELING_AFTER_G28 option
7 years ago
13176dfe2f
Merge remote-tracking branch 'origin/pr-lite-st7920-status' into pr-lite-st7920-status
7 years ago
716a22498f
Changed temp type from uint8_t to int16_t
...
- Also deleted old implementation files which had been renamed.
7 years ago
7d8c6b3f3c
Add 20x4 option for Sainsmart LCD ( #9740 )
7 years ago
aada1e698f
Removed unused configuration options.
7 years ago
c7513eb032
Merge branch 'pr-lite-st7920-status' of github.com:marcio-ao/Marlin into pr-lite-st7920-status
7 years ago
d3ca82d8c2
Support for multiple filament runout sensors
7 years ago
ca55f2927a
Pulldown pin mode support ( #9701 )
...
Implemented for LPC1768.
7 years ago
79272f98fc
Proposed changes to ST7920 lightweight status screen
7 years ago
24eb275b99
Added a light-weight status screen for the ST7920
...
- The status screen uses the ST7920 character generator to greatly
reduce SPI traffic and MCU load when updating the status screen.
- Has been tested with the RepRapDiscount Full Graphics Smart Controller
but should work with any LCD that uses an ST7920 or fully compatible
controller.
7 years ago
08d685c97a
Followup to 21e60fd
7 years ago
21e60fd3ed
Allow user to control Z-Height correction for off mesh movements ( #9661 )
7 years ago
4880ac6533
Added a light-weight status screen for the ST7920
...
- The status screen uses the ST7920 character generator to greatly
reduce SPI traffic and MCU load when updating the status screen.
- Has been tested with the RepRapDiscount Full Graphics Smart Controller
but should work with any LCD that uses an ST7920 or fully compatible
controller.
7 years ago
2ec65051fd
Fix serial comment sp.
7 years ago
2014d38e10
NEOPIXEL_BRIGHTNESS parity
7 years ago
b5e92f4f90
[2.0.x] Enable / disable PSU automatically ( #9503 )
7 years ago
16739264d3
Add UltiController v2.1 support
...
Add compatibility with the original screen bord from Ultimaker 2 printer (UltiController v2.1 with the PG-2864ALBP I2C display)
7 years ago
4925f60cff
Add MALYAN_LCD to configs
7 years ago
7d6c009104
Add thermistor 15 tuned for JGAurora A5
7 years ago
348b454401
Probe bounds based on bed size
7 years ago
58ed9901d7
Consistent NEOPIXEL_TYPE options
7 years ago
fa432508b0
Followup to Ender config
7 years ago
048486390e
Bring some configs up to date
7 years ago
f7efac57b7
Multi-host support
7 years ago
5295b4713d
[2.0.x] add semitec 104NT-4 ( #9119 )
...
Table is very very similar to old 104-GT2 so I added only the name and recycled old ID
7 years ago
0b4a46fa6c
Bring configs up to date with 1.1.x
7 years ago
f0a8a1a853
[2.0.x] Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE ( #8866 )
...
* Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE
7 years ago
28fc8741d6
Reduce default jerk. XY by half. Z by 1/4
7 years ago
ea1a8d1223
add original RADDS LCD + Controller
...
adds setup for the original Radds Display+Controller+SD Card Reader PCB
http://doku.radds.org/dokumentation/lcd-display/
7 years ago
b055d8c39c
[2.0.x] Adding support for using the MKS_12864OLED with the SSD1306 controller ( #8814 )
...
* Adding support for using the MKS_12864OLED with the SSD1306 controller
* Update comment for correct controller type
7 years ago
15d05748df
Adding support for the Tronxy and Zonestar LCD
7 years ago
69d49a2438
Shorter segments may be better
7 years ago
ae663a4198
PROBE_DOUBLE_TOUCH => MULTIPLE_PROBING
7 years ago
c1184552ac
Change K1 to required option PID_K1
7 years ago
aa7efb96bf
Bring configurations up to date
7 years ago
0154e3480c
New feature: BED_SKEW_CORRECTION
7 years ago
ef2531558c
Add an option to segment leveled moves
7 years ago
5926c9c97b
Followup for MESH_EDIT_GFX_OVERLAY
7 years ago
5ce7f23afa
Config option G26_MESH_VALIDATION for all meshes
7 years ago
3f0a982b8c
Move Filament Width Sensor to Configuration_adv.h
7 years ago
b76e173205
Move test extrusion options under G26
7 years ago
81b91b3f9d
Clean up some trailing white-space
7 years ago
967104e1ce
Default Extrusion Settings were off a few lines in some of the example config files. ( #8333 )
7 years ago
ed62c621d7
Fix G26 Circle Drawing. Add Default Extrusion Settings ( #8313 )
...
- Fix G26 Circle Drawing.
- Add default extrusion settings so machine can print lines on print bed
- Yet to be done: Get LCD Menu's to use these settings.
7 years ago
2c099fd4c2
Update Thermal Protection Documentation
7 years ago
d83a9a53e8
Merge pull request #8220 from thinkyhead/bf2_serial_port_-1
...
[2.0] Add SERIAL_PORT -1 option for configurators
7 years ago
93ba72ea83
Add SERIAL_PORT -1, set on SBASE, STM32F103RET6
7 years ago
7e43dd1d23
Fix probes configuration url
...
Based on #8241 by @machaj
7 years ago
9cc1d8e312
[2.0.x] Support for SilverGate Board
7 years ago
34be5d33c0
The plural of 'axis' is 'axes'
7 years ago
7fad26549b
Concise SD_REPRINT_LAST_SELECTED_FILE description
7 years ago
46e9eae159
Tweak to M100 config comment
7 years ago
7f55d82fd1
Move UBL_SAVE_ACTIVE_ON_M500 to Configuration.h
7 years ago
580b6e9089
Apply physical limits to mesh bounds
7 years ago
5f87324536
Fix some config verbiage
7 years ago
6296ab2173
Add GFX overlay to UBL mesh edit ( #8038 )
...
* Add GFX overlay to UBL mesh edit
Fixed misplaced HAS_TEMP_BED in dogm_bitmaps.h
rename _lcd_babystep_zoffset_overlay to _lcd_zoffset_overlay_gfx and move it out of BABYSTEP_ZPROBE_OFFSET to we can use it for over things. Add this function into UBL mesh edit screen.
update all Configuration.h to add ENABLE_MESH_EDIT_GFX_OVERLAY
* Add Sanity to UBL insanity
Need to check for DOGLCD otherwise error out.
7 years ago
572cf0ec95
UBL able to generate mesh and save and load it on 32-bit platforms ( #8015 )
...
* Get UBL Mesh Generation, Mesh Save & Mesh Load working with 32-Bit platforms
* clean up read_data() and write_data() for non-LPC1768 HAL's
* Get read_data() and write_data() return codes consistent
All HAL's read_data() and write_data() return false if they succeed.
* Get read_data() and write_data() return codes to be consistent
Make read_data() and write_data() return true if an error happens.
* Say UBL is now checked out on machine types in default Configuration.h file.
7 years ago
eeb4611606
Add proper support for the AZSMZ 12864 LCD on a SMART RAMPS
7 years ago
014a83fe09
Merge pull request #7984 from thinkyhead/bf2_micromake_c1
...
[2.0.x] Micromake C1 Configurations, Unaccented French
7 years ago
34a261416f
Add unaccented French language
7 years ago
b206f70693
Split the software endstop capability by axis.
7 years ago
a11e6a1022
Different NEOPIXEL types
...
Same as #7728 but for 2.0.x,
Lot of cleanup and remove references in whole code to other "LED files" than leds.h. Now will be much easier to add next drivers/libraries. e.g. FastLED. But bad news, currently FastLED is suporting only RGB devices (no RGBW)
7 years ago
e9bcb9d048
Add 4 new LCD displays
7 years ago
9fe7f53216
Misc general spacing cleanup
7 years ago
508d764d63
Add serial XON/XOFF handshaking
...
From @ejtagle, originally #7459
7 years ago
90af1fe5ee
Implement NO_MOTION_BEFORE_HOMING option
7 years ago
bea3ec2724
M355 S0, S1 fixes & faster LCD, SD card
...
fix Travis error
7 years ago
7cd5eb6d42
Update LEVEL_BED_CORNERS config option
7 years ago
4c5be9bb05
Fix a PARKING_EXTRUDER comment
7 years ago
494b0eba2d
Config spacing fix
7 years ago
f37ed314e0
Friendly layout for Arduino IDE
7 years ago
f536c4dccb
Move configs
7 years ago
e4fcf460e7
Marlin bugfix-2.0.x Version/README
7 years ago
54d48130f3
Slovak UTF-8 translation
...
Slovak UTF-8 translation
7 years ago
4817b39d98
Added new feature for AutoParking Extruder (APE)
7 years ago
385f1bb9e5
Merge pull request #7504 from thinkyhead/bf1_servo_delays
...
Individual servo delays
7 years ago
a1878cd1c0
Add "Level Corners" menu option
7 years ago
e9c72978c7
Implement SERVO_DELAY as array
...
This modify give SERVO_DELAY x servo basis
7 years ago
97c21e9007
Support for Geeetech GT2560 Rev.A/Rev.A+
7 years ago
Scott Lahteine