f643f4d674
Test and refactor
11 years ago
bbe8fbe13d
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
c8cdd1fc6f
Bugfixes for language option 6 (russian)
11 years ago
7395dafc1e
semantic changes in language.h
11 years ago
fad2a60ce6
Corrections for preheat extension in language.h
11 years ago
eecda434fb
Sanguinololu servo pins set default disabled
11 years ago
944ced87c5
Extended Preheat options
...
Preheat LCD menus base on code by D-Base
11 years ago
06709ad60e
Added servo pin assignments to Sanguinololu
11 years ago
3906f27c46
Individual extruder flow rate
...
Extension of M221, Tune menu
11 years ago
a38c90ee84
Added estop handling
11 years ago
a00cec8b71
Merge pull request #833 from mattsch/optional_feedrate_multiplier
...
Add support for disabling encoder control for feedrate multiplier
11 years ago
af8be9013b
Merge branch 'lcd_detected' of https://github.com/whosawhatsis/Marlin into Marlin_v1
11 years ago
0ddee3c7db
Prevent SD card insertion from causing a hang when using LiquidTWI2 device detection
11 years ago
272072fa20
Added M112
11 years ago
aab61e63c3
FWRETRACT in mm/s
...
Firmware retraction now stores the retract and recover speeds in mm/s
instead of mm/min. This makes it match the units of the maximum
feedrate, and fixes problems with modifying the value via LCD control
panel. From gcode, the values are still taken in mm/min to match the
units of G1 and similar, and they are converted to mm/s before they are
stored.
I also lowered the default retract feedrate to make it less likely to
cause problems for geared extruders when the user hasn’t bothered to
set a reasonable maximum feedrate, though users should be setting both
of these values to suit their hardware.
11 years ago
6cd85e6008
Add support for disabling encoder control for feedrate multiplier
...
Signed-off-by: Matthew Schick <matthew.schick@gmail.com>
11 years ago
09af1b90b8
Added CHDK support
...
Added CHDK support to take pictures instead of doing an IR command, see more about how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
11 years ago
765b2da3d4
Added CHDK support
...
Added so M240 can be used to trigger CHDK instead of sending an IR signal, see more about CHDK here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
11 years ago
881e348eed
Update Configuration_adv.h
...
Increase Z_HOME_RETRACT_MM to 2mm default to avoid end stop not switching during retract.
11 years ago
5a332df47e
Merge https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
15d1b8d719
Fixed finnish translation
...
- Fixed Few finnish transalations
- Removed duplicate contrast define
11 years ago
7325d7102e
Activate LiquidTWI2 device detection and space-pad LCD status line.
11 years ago
7f76a0e064
Merge pull request #813 from drf5n/PID_DEBUG
...
temperature.cpp: Fix PID_DEBUG compile error.
11 years ago
fcd8524b6e
Only increase EEPROM version for DELTA printers.
11 years ago
8ea5665ee2
Merge remote-tracking branch 'origin/Marlin_v1' into add/M665-set-delta-configuration
...
Conflicts:
Marlin/Marlin_main.cpp
11 years ago
8c4377dd63
temperature.cpp: Fix PID_DEBUG compile error.
11 years ago
fde8c2c310
Merge pull request #807 from Cylindric3D/typofixes_upstream5
...
Various typo fixes #5 - only in comments, no code changes.
11 years ago
fdce91192e
Various typo fixes - only in comments, no code changes.
11 years ago
d819c55395
Various typo fixes - only in comments, no code changes.
11 years ago
fd4542f33a
Merge pull request #805 from whosawhatsis/M200
...
autretract fix
11 years ago
e8291ed728
Merge pull request #802 from Makers-Tool-Works/Marlin_v1
...
Clarify which PID values to enter
11 years ago
465b654d24
Merge pull request #797 from Cylindric3D/update_menu_plan
...
Update menu plan
11 years ago
88506a80c3
Merge pull request #789 from smiler/Marlin_v1
...
Fixed typo.
11 years ago
b514d3c87f
Merge pull request #781 from Cylindric3D/typofixes_upstream
...
Various typo fixes #3 - only in comments, no code changes.
11 years ago
77df0d689a
autretract fix
...
I made these changes previously, but I can’t find the commit now. This
reapplies the changes to get auto retract working again.
Conflicts:
Marlin/Configuration_adv.h
Marlin/Marlin_main.cpp
11 years ago
cc5f1d475c
Merge pull request #772 from ellensp/Marlin_v1
...
Updated gen3+ board pins names to current convention
11 years ago
91759dede6
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into typofixes_upstream
11 years ago
557217fc05
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into update_menu_plan
11 years ago
aee63afccd
Clarify which PID values to enter
...
Users can be confused as to which values to enter after a PID tune. Updating the message to help clarity it.
New message: "PID Autotune finished! Put the last Kp, Ki and Kd constants from above into Configuration.h"
Old message: "PID Autotune finished! Put the Kp, Ki and Kd constants into Configuration.h"
11 years ago
99f6326544
Remove unnecessary dependency on time.h from qr_solve.cpp
...
Fixed compiler errors on Ubuntu using arduino-core
11 years ago
ea669cb504
Fix some extra and some missing tabs, to make the file consistent.
11 years ago
b46a1b6360
Update the menu plan document with the current menu as per ultralcd.cpp.
11 years ago
3cc7626d1f
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into update_menu_plan
11 years ago
174b8d99d5
Simplify 3-point probing using new code only
11 years ago
3b718b816c
better documentation
11 years ago
34fd59c370
ABL at any points
11 years ago
541155ea87
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into typofixes_upstream
11 years ago
9fa328e5c8
Merge pull request #793 from MissionSt/use_axis_enums
...
Use constants instead of numeric literals
11 years ago
f308a8af91
update comment
11 years ago
357e31270a
Prevent G29 without first homing in X and Y
...
If position is unknown, then G29 can be dangerous.
11 years ago
d2d7d186b5
Use descriptive constants, more
11 years ago
2ccdf4f36d
Use descriptive constants instead of numeric literals
11 years ago
c00383f286
Fixed typo.
11 years ago
60f72a78a9
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into typofixes_upstream
11 years ago
abba7a0003
Merge pull request #782 from marcovannoord/Marlin_v1
...
Added dutch to language.h
11 years ago
b868d668fa
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into typofixes_upstream
11 years ago
8212d8d543
Revert "Fixed small typo that would prevent compiling"
...
This reverts commit 51ae4881ab
11 years ago
46bae30573
Merge pull request #776 from whosawhatsis/fwretract
...
Fwretract fixes, cleanup
11 years ago
51ae4881ab
Fixed small typo that would prevent compiling
11 years ago
498d76fd79
Fixed some messages where the text shown on the screen was more than 17 characters
11 years ago
af9395ac2e
Add M605 to dynamically set delta configuration
...
Save above configs in eeprom
fix docs in createTemperatureLookupMarlin.py
add missing azteegX3pro digipot settings in delta example config
11 years ago
fd42f0d226
Merge pull request #783 from MissionSt/fix/syntax-error
...
Fix compile error
11 years ago
96217bf36a
Merge pull request #777 from PxT/M114
...
Add whitespace to M114 output
11 years ago
cf5c3b6610
Added dutch to language.h
11 years ago
d1c64b9dc4
Fix syntax error introduced in 477b6fa1d
11 years ago
5d50819791
Various typo fixes - only in comments, no code changes.
11 years ago
3f455889d0
Merge pull request #769 from Cylindric3D/typofixes_1
...
Various typo fixes - only in comments, no code changes.
11 years ago
4ddedb3b27
Merge pull request #780 from Cylindric3D/typofixes_2
...
Various typo fixes #2 - only in comments, no code changes.
11 years ago
d4ba23bc28
Merge pull request #770 from josefpavlik/Marlin_v1
...
Marlin v1
11 years ago
bbb424bd2f
Merge pull request #779 from MissionSt/makefile-fix-abl
...
Makefile fixes
11 years ago
8f0cee2a14
Various typo fixes - only in comments, no code changes.
11 years ago
08263ae66e
Merge branch 'Marlin_v1' into typofixes_1
11 years ago
5bd09d26e2
Makefile works with auto bed leveling
11 years ago
b45beeffd6
typo fix in Makefile
11 years ago
306588925d
Add whitespace to M114 output
11 years ago
c43838bb1e
disable auto retract by default
...
This should make it safe to enable FWRETRACT by default, with
autoretract (which should now be fixed) only enabled by M209. FWRETRACT
should probably now default to enabled (to make G10/G11 and M207-209
available, without changing functionality when they are not used), but
I’ll save that for another pull request/discussion.
11 years ago
99f0e44864
Move FWRETRACT defaults to configuration_adv.h
11 years ago
66e3869138
Fix autoretract
...
This takes the (now working) G10/G11 code and moves it to a function,
which is called by G10 and G11, and also called by G1 if autoretract is
enabled and a retract/recover move is detected.
11 years ago
2f2459c0db
Fix G10/G11 Z-lift
11 years ago
8c5675c290
Use language.h instead of English literals for "bed"
11 years ago
0f7393a13e
Refactor 'accurate' auto bed leveling to use probe_pt()
11 years ago
c4fbb44d6d
Refactor 3-point auto bed leveling to use probe_pt()
11 years ago
ad2c6488c7
Add probe_pt(), useful for auto bed leveling
11 years ago
c9c83a4560
Updated gen3+ board pins names to current convention
11 years ago
ab0d3c4fb3
Various typo fixes - only in comments, no code changes.
11 years ago
477b6fa1df
move engaged from lcd console refreshes power off timeout
11 years ago
831fc2a952
Pt100 and Pt1000 temperature sensors handling
11 years ago
7dcd350941
A few changes to Russian, changed LCD strings to be <=17 characters.
11 years ago
c31bb2b7ad
Only show the ZProbe offset when auto-bed-leveling is enabled.
11 years ago
46f5bea19f
Add configurable beep for UltiPanel.
11 years ago
d16a770855
Ultimainboard 2.x does not has a PS_ON pin.
11 years ago
71bb3a8133
Add comments for Ultimainboard 2.0 configuration.
11 years ago
9b7d87e885
Remove duplicate contrast define.
11 years ago
816f0a678a
Merge pull request #768 from whosawhatsis/Marlin_v1
...
multiple FWretract fixes
11 years ago
6e43398509
G10/G11 bugfixes
...
Previous version was broken by using G92 E0 between retract and recover.
11 years ago
d6c5c503d4
correct feedrate units in comments for M207/M208
11 years ago
15d6116188
Merge pull request #689 from cajun-rat/tidy
...
Use C++ initialization list
11 years ago
0b9ecf3824
Language cleanup, part 1.
11 years ago
b5ba5c1465
Merge branch 'Marlin_v1' of https://github.com/whosawhatsis/Marlin into Marlin_v1
11 years ago
78e7654601
Keep FWRETRACT values in terms of millimeters when using M200
...
for volumetric E units
11 years ago
3f6d44d40b
Keep FWRETRACT values in terms of millimeters when using M200 for volumetric E units
11 years ago
363dc2f0e8
Merge branch 'Marlin_v1' into update_menu_plan
11 years ago
5f797ca29f
Updated Polish, changed default firmware URL to Marlin.
11 years ago
0778f5f028
Add missing entries to the new Aragonian language.
11 years ago
54bab3e0d0
Merge branch 'Marlin_v1' into localisation
...
Conflicts:
Marlin/language.h
11 years ago
bdd0211aeb
Move strings in ultralcd.cpp into language.h.
11 years ago
c8e5a82d49
keep English as default lang.
11 years ago
f64592e362
Add Aragonese translation
11 years ago
ac74f45dc0
Merge pull request #752 from MatixYo/patch-3
...
Update language.h
11 years ago
36086d3ca4
Update language.h
...
Updated Polish translations.
11 years ago
1781031f2d
Update LCD Menu Tree with current options, based on ultralcd.cpp and language.h.
11 years ago
d485988bec
fix typo
11 years ago
8a1fd25363
Default is to not define digipot_i2c
11 years ago
5097c57d3a
Added pins for Azteeg X3 Pro under motherboard 68
11 years ago
b819fc53ca
Add Azteeg X3 Pro as motherboard 68
...
Add digipot i2c control for MCP4451
Allow M907 to set i2c digipot currents in amps
Fix Makefile to allow Azteeg motherboards
Fix Makefile to allow Wire libraries only
Add beeper pin for Azteeg X3 Pro
11 years ago
e1ae7952eb
Merge pull request #743 from Opticalworm/Marlin_v1
...
Improved support for panelolu2 encoder and buzzer
11 years ago
a5f53f0cf3
Heater wattage reporting for M105 using EXTRUDER_WATTS and BED_WATTS
11 years ago
8d162e5bd7
Improved support for panelolu2 encoder and buzzer
...
I added #define for LCD_FEEDBACK_FREQUENCY_HZ and
LCD_FEEDBACK_FREQUENCY_DURATION_MS which is used to alter the default
buzzer sound.
When selecting Panelolu2 in configuration.h:
- it automatically sets the correct ENCODER_PULSES_PER_STEP and
ENCODER_STEPS_PER_MENU_ITEM.
- if LCD_USE_I2C_BUZZER is defined it will also set the default
LCD_FEEDBACK_FREQUENCY_HZ and LCD_FEEDBACK_FREQUENCY_DURATION_MS
When selecting the sanguinololu 1284p the following is true:
- its now enables LARGE_FLASH
- It enables the gcode M300 when the panelolu2 LCD_USE_I2C_BUZZER is
defined
11 years ago
b2c11ba980
Change diameter code to 'D'
...
For some reason that I can’t figure out, the decimal is dropped when
using ’S’ for the code.
Also some minor code improvements to M200.
11 years ago
61059385a3
Merge pull request #737 from whosawhatsis/M200
...
M200 implementation
11 years ago
856edfcc0d
Fixed math
...
This is why I wanted to sleep on the code I wrote while falling asleep
rather than immediately submitting a pull request.
11 years ago
0d81ae77bc
Merge pull request #727 from drf5n/oversampling
...
temperature.cpp: Actually use OVERSAMPLENR in the oversampling calculation.
11 years ago
84df13f7d1
Merge pull request #721 from drf5n/lcdOnly
...
Enable basic ULTRA_LCD screen w/o encoders and menus.
11 years ago
4c7e9502ad
Merge pull request #718 from drf5n/temptableRes
...
createTemperatureLookupMarlin.py: Add resolution comments and format for...
11 years ago
652a0f6b5a
Merge pull request #717 from drf5n/tpins2
...
fastio.h: Add AT90USBxx_TEENSYPP_ASSIGNMENTS for teensyduino/Lincomatic/...
11 years ago
96a0cdc541
Merge pull request #716 from drf5n/maketeensy
...
Makefile: Update for Arduino 1.0.5 and Teensyduino dependent boards (HAR...
11 years ago
d24df7af2c
M200 implementation
11 years ago
f0b8d5ba3d
createTemperatureLookupMarlin.py: Change comment to refer to actual program name.
11 years ago
50f44d9249
createTemperatureLookupMarlin.py: Truncate to short after application of OVERSAMPLENR for improved resolution.
11 years ago
f5b5dd8038
createTemperatureLookupMarlin.py: Add output of Steinhart-Hart coefficients.
11 years ago
76cf07c3f7
Configuration.h: Use OVERSAMPLENR in dT_PID definition.
11 years ago
476c7193d8
temperature.cpp: Use OVERSAMPLENR in oversampling calculation.
11 years ago
f08bb8bb6a
Previous commit borked.
11 years ago
b1f8f492c6
Remove previous_millis_cmd update from extruder runout prevention code
...
This seems to defeat the purpose of previous_millis_cmd, preventing the
time elapsed from previous_millis_cmd from ever reaching
max_inactive_time or stepper_inactive_time while the heat was on.
11 years ago
8a5eaa3c9b
Fix crash after home bug
...
Fixes a bug in the Extruder Runout Prevention feature that caused the
extruder to move back to “current_position” after a move if it was
activated while the move was in progress. For long home moves (which
are longer than the dimensions of the machine’s working area), this
would cause the machine to crash into the far end of its travel after
homing. This usually occurred on the Z axis, which could result in
damage to the machine if you don’t hit the reset button in time.
11 years ago
61a7256d42
Enable basic ULTRA_LCD screen w/o encoders and menus.
11 years ago
fdac8f6cec
Update ConfigurationStore.cpp
...
Unable to compile if ENABLE_AUTO_BED_LEVELING is not set (not set by default).
11 years ago
05932e4458
Add Z Probe Offset to EEPROM and Ultra LCD
11 years ago
7216583b8b
createTemperatureLookupMarlin.py: Add resolution comments and format for Marlin.
11 years ago
e8e0697e48
fastio.h: Add AT90USBxx_TEENSYPP_ASSIGNMENTS for teensyduino/Lincomatic/Printrboard compatibility.
11 years ago
75f39fadfc
Makefile: Update for Arduino 1.0.5 and Teensyduino dependent boards (HARDWARE_MOTHERBOARD=={8,81,82,83,84})
11 years ago
df194f75e1
Added PT100 support for Ultiboard2
11 years ago
380144c20f
Add Ultiboard2 electronics. With PWM current settings. For the few people that have this new board as experiment in their UM-Original.
11 years ago
6ae7f7870d
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into ErikZalm
...
Conflicts:
Marlin/Configuration.h
Marlin/Marlin_main.cpp
11 years ago
17d6d965dc
Use C++ initialization list
...
This is the recommended approach for object initialization. The change
doesn't affect binary size (although in theory it could make it smaller).
11 years ago
ce8b9c4fc5
Correct missing parameter from last upmerge
...
Signed-off-by: Joseivaldo Benito Junior <jrbenito@benito.qsl.br>
11 years ago
8e48e24c7f
Update Delta example files
...
Signed-off-by: Joseivaldo Benito Junior <jrbenito@benito.qsl.br>
11 years ago
46d2443c7d
Merge pull request #676 from IVI053/Marlin_v1
...
Minor improvements for encoder configuration, LCD entry for PSU controll and thermistor pins on RAMPS
11 years ago
eed053dffb
Revert "Made numbering of heat bed thermistor more logical as D8 is bed, D9 is Extruder 2 and D10 is Extruder 1, so T0 should be E1, T1 E1 and T2 bed to be sequential as MOSFET-Outputs"
...
This reverts commit b7eadb9f37
11 years ago
8349fc89a4
Fixed planner bug
11 years ago
da2a6f9a31
Accurate bed leveling: x loop inside y and zigzag motion
11 years ago
d29615dc0c
Z and Y dual stepper drivers error
...
if you try to enable Z_DUAL_STEPPER_DRIVERS the error "You cannot have dual drivers for both Y and Z" shows even if you don't have defined Y_DUAL_STEPPER_DRIVERS and don't let you compile the firmware
to solve this problem i change this line:
#ifdef Z_DUAL_STEPPER_DRIVERS && Y_DUAL_STEPPER_DRIVERS
to:
#if defined (Z_DUAL_STEPPER_DRIVERS) && defined (Y_DUAL_STEPPER_DRIVERS)
now the error only show if you define both Z_DUAL_STEPPER_DRIVERS and Y_DUAL_STEPPER_DRIVERS
11 years ago
5bde7fcb28
Minor code and comment polishing
11 years ago
20faff5935
Incorporate PS_DEFAULT_OFF for starting state on LCD menu entry
11 years ago
e5d3044801
Added posibility to set ENCODER_STEPS_PER_MENU_ITEM in Configuration.h like ENCODER_PULSES_PER_STEP as it depends on it for usability
11 years ago
b7eadb9f37
Made numbering of heat bed thermistor more logical as D8 is bed, D9 is Extruder 2 and D10 is Extruder 1, so T0 should be E1, T1 E1 and T2 bed to be sequential as MOSFET-Outputs
11 years ago
e8786bf110
Added support for Cheaptronic v1 electronic
11 years ago
cc2925b705
Implemented a least squares fit of the bed equation for auto bed leveling.
...
The code for the LSQ solver (qr_solve) is copyrighted by John Burkardt and released under LGPL here:
http://people.sc.fsu.edu/~%20jburkardt/c_src/qr_solve/qr_solve.html
(see qr_solve.cpp for further copyright information)
11 years ago
b64661070e
Fixed the plane vector equation to a simpler one (only dependent on the normal)
...
Removed the calculation of the inverse matrix since the rotation matrix is orthogonal, therefore inverted == transposed.
Much simpler and mathematically robust.
11 years ago
5c44f6c434
Bed Heater monitoring in Controller Fan
...
In some cases the Bed Heater FET heats up more then stepper drivers, so
this change add the bed monitoring to the controller fan. As soon as the
bed heater is turned on, the controller fan will run as well.
11 years ago
b33375d438
Z Axis Safe Homing when using Z Probe
...
Recommended for those who are using the Z Probe for Z Homing (as
Z-Endstop)
This feature has two changes:
1) Allow user to choose where the Z Probe will touch the bed when homing
all axis together (G28) by setting below defines:
Z_SAFE_HOMING_X_POINT
Z_SAFE_HOMING_Y_POINT
2) Prevents the user to perform Z Axis Homing when the Z Probe is
outsite bed.
11 years ago
35905ea4f9
Allow heaters to stay full On when PWM=127
...
In previous version, even with PWM = 127, the system turns the FET off
and then on in the next cycle. This bevavior may increase the FET heat
dissipation.
It was fixed keeping the FET always On when PWM=127.
11 years ago
a94e588765
Changed slow buttons behavior.
11 years ago
69af392554
Added HEATERS_PARALLEL (Request from reifsnyderb)
...
This allows a hot end with two heaters and a FET for each heater. This is useful if the FET is not capable of heating two heaters.
11 years ago
48a185d004
Fixed compile errors from bad commits.
11 years ago
24d1f480b6
Merge pull request #647 from shaggythesheep/newfeature-M226
...
Implement M226 - GCode Initiated Pause
11 years ago
95b41413e6
Merge pull request #641 from hugokernel/master
...
M80 - ATX Power On related modification
11 years ago
59b96e323e
Merge pull request #640 from fmalpartida/SAV-MkI
...
Added support for BT on AT90USB devices, corrected LCD bug, added new board and LCD
11 years ago
2433ee6fc8
Merge pull request #637 from justuswilhelm/Marlin_v1
...
Fix servo control for Melzi v2.0
11 years ago
3455a2bac2
Merge pull request #636 from PrintToPeer/Marlin_v1
...
Add UUID support to M115 responses.
11 years ago
dc887ef99b
Implement M226 - GCode Initiated Pause
...
Implemented M226 as described here:
http://reprap.org/wiki/G-code#M226:_Gcode_Initiated_Pause
Waits for pin to be become either HIGH, LOW or the inverse of what it
was before. Allows printing to pause until user interaction
11 years ago
c244eb860c
If you have a switch on suicide pin, this is useful if you want to
...
start another print with suicide feature after a print without
suicide...
11 years ago
7b556d2e96
Added BT support on AT90USB devices
...
Added AT90USB device BT connectivity support using second UART.
11 years ago
a5e8575829
Add UUID support to M115 responses.
11 years ago
cab84e0e5b
Add (correct) missing pin definitions for Y2
...
I tested this and it works.
11 years ago
5b3f60ea2e
Corrected LCD only error
...
If only an LCD is defined and no menu or keyboard defined, there is a
compilation error.
Added conditional compilation.
11 years ago
62d0b79023
Fix servo control for Melzi
11 years ago
b5a964fcc5
Initial SAV MkI (RepRap CloneWars board) integration.
...
Included support for BT dongle on AT90USB boards.
Added LCD Shift Register LCD control
Included support for RepRap Clone Wars project board (SAV MKI).
11 years ago
f941203172
PS_ON configurable boot state
...
Allows the user to select wheter or not the PSU should be turned on or
kept in standby when marlin boots
11 years ago
c79e3967b3
Make G11 not horribly broken
11 years ago
d69822ed51
Fix '#'
...
since it can occure in comments.
11 years ago
2fb2a0a119
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
39d88bcccb
preparation for hibernation
...
If a print is stopped, it would be nice in the future to write a file with the printer state, the filename of the print, and the position within the print.
this file could be read, to continue a previously stopped print.
not finished yet.
11 years ago
ab965376ff
Sub-file calls.
...
by overloading M32 it is now possible to execute gcode files from other gcode files, with a fixed recursion level.
This can be used e.g. for having a real start.g and end.g somewhere on the sd card, which are then called from the normal print file.
Another usecase would be to have macro-files for nozzle-change and layerchange.
I have not tested the speedwise performance. The testing was done with pronterface.
syntax:
normal call from sd card will open the new file and continue executing there.
M32 !/path/filename#
this however will call the new file and return to the caller file.
M32 P !/path/filename#
with the optional "S<position>" the file starting position can be set.
this is for continuing prints from a previous location.
11 years ago
b2cc27e5ea
Added a magic character for sd buffering.
...
if a '#' is read now the buffer will be emptied before reading ahead.
This is so one can execute files from within gcode files, without messing the buffer with preread characters from the caller file.
# can not occure in sd files imho, because it should only occure within checksums in ther serial communication.
Yes, thats a lame argument. If you have a better idea please tell me. It has to be a character that one can type
on a keyboard manually.
11 years ago
8a08cca0f2
Added temperature status less.
...
Hopefully fixed viky button handling without braking other boards
11 years ago
667d278f54
Revert "Fix for Viki display"
...
This reverts commit 314fd13c39
11 years ago
bf27e79e74
Small BlinkM fix
11 years ago
87e28c0599
Added ifdefs to blinkm
11 years ago
24c6b2ab35
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
6a803ba9c5
Merge pull request #590 from timkoster/Marlin_v1
...
Added BlinkM support over i2c
11 years ago
457d8a0acb
Fixed merge conflicts
11 years ago
6f85a8c7aa
Bed auto Leveling change: Raise Z before homing
...
- Added "Z_RAISE_BEFORE_HOMING" for raising Z the defined distance
before homing. This is useful to avoid Z-Probe collision when hotend is
near bed.
- Fixed the issue of Z not going bellow Z_PROBE_OFFSET when
"min_software_endstops" is true.
Now the Z_PROBE_OFFSET is not set in Z_MIN_POS, it is added after
homing.
11 years ago
dd3086d3f2
Show Temperature ADC values
...
If "SHOW_TEMP_ADC_VALUES" is defined in Configuration_adv.h, the M105
command will present, after tradicional temperatures, the ADC value read
from temp sensors. This is great for adjusting thermistor tables with
thermocouple.
From Pronterface you can see the ADC value and compare with a
thermocouple reading.. then you just need to create your own thermistor
table.
Since this merge doesnt change the original information, it doesnt mess
with PC software parsing (tested under Pronterface and Repetier-Host).
11 years ago
7fad13a1e2
Reverse SD card file name order.
...
This is _not_ automatically the cronological, since deleting a file will free
the filesystem descriptor for it, which then will be used by the next file copied on it.
Since this makes the auto0.g file very inaccessible, I put the option back, to have it in the prepare menu.
this should satisfy https://github.com/ErikZalm/Marlin/pull/373
as a reminder, auto0.g will be executed every time after a boot with sd card present and file present.
thereafter, if there is a file auto1.g this will be done. Thats IMHO the best place to put settings, and prepare heating.
I also execute again after each (now again via the prepare menu) before starting a new print/ after a failed one.
It for me 100% replaces any start.gcode form the slicers.
11 years ago
b832f5b9f6
added delta tower babystepping. Its untested, but hopefully florian horsch will be able to try.
...
also, removed some trouble for compilation with corexy.
I think that babystepping is only possible in z for a delta tower.
not sure if it would be usefull to step individual motors on a delta, i don't own one
11 years ago
c38b0855c8
I think that filament change is ready for the masses. I have tested very often with my ultimaker.
...
I strongly vote for it being a single gcode, because otherwise the triggering from the menu is terrible.
11 years ago
d147a057ac
Add the socalled "Babystepping" feature.
...
It is a realtime control over the head position via the LCD menu system that works _while_ printing.
Using it, one can e.g. tune the z-position in realtime, while printing the first layer.
Also, lost steps can be manually added/removed, but thats not the prime feature.
Stuff is placed into the Tune->Babystep *
It is not possible to have realtime control via gcode sending due to the buffering, so I did not include a gcode yet. However, it could be added, but it movements will not be realtime then.
Historically, a very similar thing was implemented for the "Kaamermaker" project, while Joris was babysitting his offspring, hence the name.
say goodby to fuddling around with the z-axis.
11 years ago
bca353cc12
Fixed duplicate define in fastio.h
11 years ago
253dfc4bc1
Bed Auto Leveling feature
...
Check the Readme for instruction how to enable and configure the feature
11 years ago
1bda6bf862
Merge pull request #609 from phq1910/patch-1
...
Update Configuration.h
11 years ago
c80aac1518
Merge pull request #610 from phq1910/patch-2
...
Update pins.h
11 years ago
314fd13c39
Fix for Viki display
11 years ago
4f7c6dfe35
Update pins.h
...
Include Pins cpu Sethi 3D
11 years ago
57173739a1
Update Configuration.h
...
Include CPU Sethi 3D
11 years ago
0dca49a7c0
Added Azteeg X3 board.
11 years ago
d8c2c810b4
Added info to the delta configuration files in the configuration.h file
11 years ago
9bc88f8bab
Placed optional ENCODER_PULSES_PER_STEP in the configuration.h file
11 years ago
3ca1ca6869
Fixed missing ENCODER_PULSES_PER_STEP
11 years ago
97b0da0c2e
Removed #ifndef BLINKM
11 years ago
61db046b32
Added #ifdef BLINKM around new code. Also refined BlinkM.h.
11 years ago
77df2ab0e7
Make Y_DUAL_STEPPER_DRIVERS disabled by default
11 years ago
ed1ab42186
Added Y_DUAL_STEPPER_DRIVERS
...
Enables two stepper drivers to be used for the Y axis (useful for
Shapeoko style machines)
Each Y driver can be stepped in either the same way or in opposite
directions, accounting for different hardware setups (leadscrew vs. belt
driven)
11 years ago
f4a59e4ce5
Revert "Added Y_DUAL_STEPPER_DRIVERS"
...
This reverts commit 7ee275b620
11 years ago
7ee275b620
Added Y_DUAL_STEPPER_DRIVERS
...
Enables two stepper drivers to be used for the Y axis (useful for
Shapeoko style machines)
Each Y driver can be stepped either the same way or in opposite
directions, accounting for different hardware setups (leadscrew vs. belt
driven)
11 years ago
6a1e980c6d
Merge pull request #600 from xoan/Encoder_Pulses_Per_Step
...
add ENCODER_PULSES_PER_STEP
11 years ago
20076a8bd3
Merge pull request #598 from GDV0/Marlin_v1
...
FIx compilation error when enabling SERVO_ENDSTOPS (#591 )
11 years ago
3626b5ad8b
Removed Delta from the default config file.
...
Changed EEPROM CHITCHAT behavior. M503 is always enabled.
11 years ago
bf7007d02f
add ENCODER_PULSES_PER_STEP
11 years ago
f17506c504
FIx compilation error when enabling SERVO_ENDSTOPS ( #591 )
11 years ago
acd8619809
Fan fix for Panelolu2+Sanguinololu.
11 years ago
595580556c
Fixed bug that makes ulticontroller knob backwards introduced Feb 28 2013 by Robert.
...
Bug introduced in version 6beb42cdf6839bef6d5d
11 years ago
88dfeefca3
Define BlinkM default disabled
11 years ago
5350faf2a2
Merge https://github.com/timkoster/MarlinBlinkM into Marlin_v1
11 years ago
7016cc9511
Added BlinkM support over i2c
11 years ago
3b315b3da0
Added BlinkM support over i2c
11 years ago
f26f26b7bd
Fix the example delta configuration as someone forgot to do it.
11 years ago
9aa2229077
add command M666 for adjusting delta printer endstop position
11 years ago
9547fb9dfb
Add duplication and auto-park mode for dual x-carriage support.
11 years ago
53614e5144
add pins for rambo lcd
11 years ago
b42d24e31e
add additional pins to avr2560 for rambo lcd
11 years ago
b0c8120fcc
Added feedrate setting in exemple config for manual moves from panel
11 years ago
a54fe2d73c
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1
...
Conflicts:
Marlin/Marlin_main.cpp
11 years ago
7ea63d08df
Merge pull request #565 from iXce/avrdudeconfpath
...
Detect OS in Makefile to use the correct avrdude.conf path
11 years ago
4187b637a5
Merge pull request #570 from hg42/separate-INVERTING-macros-for-MIN-and-MAX-endstops
...
separate INVERTING for MIN and MAX endstops (6 #defines instead of 3)
11 years ago
07e7de3600
Merge pull request #569 from hg42/convert-PROTOCOL-macros-from-statements-to-expressions
...
convert PROTOCOL macros from statements to (multiple, comma separated) expressions
11 years ago
c0c4c97db6
Detect OS in Makefile to use the correct avrdude.conf path
11 years ago
2ca983568d
separate INVERTING for MIN and MAX endstops (6 #defines instead of 3)
11 years ago
3700f688f5
convert PROTOCOL macros from statements to (multiple, comma separated) expressions
11 years ago
a504c88346
Fix a bug where the PID controllers D action kicks in hard as soon as the PID controller starts.
11 years ago
394ed08f88
Added feedrate setting for manual moves from panel
11 years ago
9bf1cf1b22
Pre-calculate diagonal rod length squared
11 years ago
4623e78ce0
Added Honeywell thermistor 135-104LAF-J01
11 years ago
d7f384f680
Skip SD menu refresh if nothing has changed
11 years ago
abc8320a68
Save LCD_CLICKED before it is cleared
...
The SD card menu was refreshing so slowly that the button interrupt was clearing LCD_CLICKED before the menu items could check it.
11 years ago
f4c3135c6d
Add Panelolu2 pins for RAMPS1.3
11 years ago
aae42c68f9
Update French translation in language.h
11 years ago
4d435c38a6
Add support of LiquidTWI2-based panels to Makefile
...
Use LIQUID_TWI2=1 as make argument to enable this support
11 years ago
6c42a3a339
Woops, fix logic
11 years ago
376d8af2c8
Report temperatures for all extruders
11 years ago
434b6a05c1
Merge pull request #552 from iXce/Marlin_v1
...
Report temperatures for all extruders in reply to M105
11 years ago
bdc2621119
Merge pull request #561 from Brendan-csel/Marlin_v1
...
Fix for Viki LCD issues printing from SD card
11 years ago
6965bd4e15
Merge pull request #560 from njprossi/Marlin_v1
...
Fixed move from panel for delta bot #557
11 years ago
a55b33e613
Merge pull request #559 from iXce/panelolupinsramps13
...
Add Panelolu2 pins for RAMPS1.3
11 years ago
8b34351537
Merge pull request #558 from iXce/frenchupdate
...
Update French translation in language.h
11 years ago
735e556724
Merge pull request #555 from iXce/liquidtwi2_makefile
...
Add support of LiquidTWI2-based panels to Makefile
11 years ago
d80aecda0a
Skip SD menu refresh if nothing has changed
11 years ago
be2dea1dc6
Save LCD_CLICKED before it is cleared
...
The SD card menu was refreshing so slowly that the button interrupt was clearing LCD_CLICKED before the menu items could check it.
11 years ago
55c287a69e
Fixed move from panel for delta bot #557
11 years ago
1902d339b0
Add Panelolu2 pins for RAMPS1.3
11 years ago
eb23a68e92
Update French translation in language.h
11 years ago
1561c6df51
Merge pull request #547 from wolfmanjm/delta-configuration
...
Setup Default configuration for Deltas if DELTA is defined
11 years ago
374bc99fa3
Add support of LiquidTWI2-based panels to Makefile
...
Use LIQUID_TWI2=1 as make argument to enable this support
11 years ago
ab624eac2a
revert COnfiguratiuon to the same as head
11 years ago
52f79ffeca
add an example default configuration for delta style bots
11 years ago
b9d7ccf1cd
Merge remote-tracking branch 'upstream/Marlin_v1' into delta-configuration
...
Conflicts:
Marlin/Marlin_main.cpp
11 years ago
d4d1540727
Use -fno-use-cxa-atexit to override gcc --enable-cxa_atexit
11 years ago
01ed99143c
Woops, fix logic
11 years ago
76841450c8
Only display poweron/poweroff if PS_ON_PIN > -1
11 years ago
44f327d738
Uniformly reindent language.h
11 years ago
326d2db025
Update language.h so that all languages compile
...
Some strings still need translation, but at least everything compiles.
11 years ago
2cb716f513
Run Marlin/language.h through dos2unix
11 years ago
34da3a0a3f
Merge github.com:ErikZalm/Marlin into Marlin_v1
...
Conflicts:
Marlin/language.h
11 years ago
18199ff960
Merge github.com:ErikZalm/Marlin into Marlin_v1
11 years ago
fb5334f428
Fixed compile error when QUICK_HOME is defined.
...
As well a couple of minor changes to handling of extruder offset for
dual x-carriage mode.
11 years ago
c3568398b5
Disable DUAL_X_CARRIAGE by default
11 years ago
39cd3dbdbe
Remove dual x-carriage functionality that could/should be implemented in slicer
...
Also added a couple of missed merge lines in homeaxis() from previous
commit.
11 years ago
fb20ceabce
enable soft endstops for delta
...
disable delta by default
11 years ago
d01ee7e7b5
fix zjerk being the same for delta as xy jerk
...
add more delta defaults
on delta make second home even slower
11 years ago
d7390e13d9
Support dual x-carriage printers
...
Dual x-carriage designs offer some substantial improvements for dual
extruder printing.
11 years ago
f3aa2a48e7
update max pos
11 years ago
460751503e
Added default configurations for deltas when DELTA is defined
11 years ago
9da94c247a
fixed bad lcd commit from makr3d
...
#elsif does not exist #elif is correct
12 years ago
59004023fd
Fixed typo
12 years ago
461dad6e05
Added : M32 - Select file and start SD print (Can be used when printing from SD card)
...
Untested
12 years ago
c4a2077951
M109 and M190 now wait when cooling down if R is used instead of S.
...
M109 S180 waits only when heating.
M109 R180 also waits when cooling.
12 years ago
8a2a3ef91d
Merge pull request #531 from iXce/Marlin_v1_lcd
...
Only clamp panel movements if software endstops are enabled
12 years ago
6397b3339c
restored configuration.h defaults
12 years ago
cdaaad3df1
Merge branch 'Marlin_v1' of https://github.com/makr3d/Marlin into makr3d-Marlin_v1
12 years ago
e3bdefd873
fixed missing #endif
12 years ago
a5be0c52c6
no message
12 years ago
e509cdbeb0
added contrast control function for gLCDs
12 years ago
99b7e926e7
added MaKr3d Melzi board
12 years ago
68be33b1fc
Update language.h
...
I update the spanish Messages, now this compile for spanish language.
12 years ago
acb3271c9a
Merge pull request #534 from xifle/Marlin_v1
...
Fixes compiler warning for feedrate deadzone
12 years ago
61fe430d4f
Should fix compiler warning for feedrate deadzone
12 years ago
fde17d5720
Fix for ugly code compilation errors in SERVO_ENDSTOP checks
12 years ago
aa65c20d1f
Only clamp panel movements if software endstops are enabled
12 years ago
ecf3ab5de4
Added thermistor 60 to configuration.h
12 years ago
2daa85918e
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
Marlin/Marlin_main.cpp
Marlin/language.h
Marlin/pins.h
Marlin/ultralcd.cpp
12 years ago
Dan Nixon