adb5375a09
Enabling servo usage on boards with PWM current control
...
Enabling servo usage on boards with PWM current control
timer5 is used by some boards like the Mini Rambo for controlling motor current via PWM, see stepper.cpp.
```cpp
#ifdef MOTOR_CURRENT_PWM_XY_PIN
pinMode(MOTOR_CURRENT_PWM_XY_PIN, OUTPUT);
pinMode(MOTOR_CURRENT_PWM_Z_PIN, OUTPUT);
pinMode(MOTOR_CURRENT_PWM_E_PIN, OUTPUT);
digipot_current(0, motor_current_setting[0]);
digipot_current(1, motor_current_setting[1]);
digipot_current(2, motor_current_setting[2]);
//Set timer5 to 31khz so the PWM of the motor power is as constant as possible. (removes a buzzing noise)
TCCR5B = (TCCR5B & ~(_BV(CS50) | _BV(CS51) | _BV(CS52))) | _BV(CS50);
#endif
}
```
Using the same timer for controlling servos results in loss of motor control. So use timer4/3 for those boards instead.
[See discussion here.](http://shop.prusa3d.com/forum/software-f13/enabling-auto-leveling-in-firmware-t416-s40.html )
9 years ago
04e57e2b5e
Update the Hephestos 2 default config
9 years ago
f260e00a72
fix spelling
...
Thermister -> Thermistor
9 years ago
b1a3a95ad4
Tweak controllerFan to save a cycle or two
9 years ago
04a6924633
Make DISABLE_INACTIVE_X, etc., the same as DISABLE_X (etc.) if missing
9 years ago
15fccd43ee
Fix spacing of an #endif
9 years ago
be08eb6153
Merge pull request #3194 from jbrazio/feature/add-pt_pt-utf8
...
Add pt_pt-utf8 language pack and fix some minor compiler warnings
9 years ago
d1ff7959b7
Merge pull request #3188 from esenapaj/patch-1
...
follow-up the commit b82d91e
9 years ago
10caee2b7c
Merge pull request #3187 from AnHardt/target_extruder_number
...
Fix extrudernum in MSG_INVALID_EXTRUDER
9 years ago
1cc316f1fd
Merge pull request #3082 from thinkyhead/updated_2820
...
This is quite comprehensive. If probes are disabled in any case when they shouldn't be, I'm sure we will hear about it soon.
9 years ago
7bf5d117e7
Merge pull request #3069 from thinkyhead/rc_delta_compat_m48
...
Delta-compatible extensions to M48
9 years ago
db8ab50c66
Merge pull request #3192 from tnw513/fix_lang
...
Added missing translations.
9 years ago
06332f20be
Merge pull request #3113 from jbrazio/bugfix/3061-stop-print-time-counter
...
Stop print timer with M105/M109
9 years ago
92a7d4515a
Missing coma comment correction for the default cofig file
9 years ago
1aa531a3db
Missing coma comment correction for all config files
9 years ago
68dda08fff
Added pt_pt-utf8 language pack; Fixed some minor compiler warnings; Harmonize file suffix for the current existing UTF8 language packs; Updated all configuration files to reflect the new language packs
9 years ago
f8c10d6b0e
Added missing translations.
9 years ago
468df96b0f
follow-up the commit b82d91e
...
follow-up the commit b82d91eca6
9 years ago
338b69c24b
Fix extrudernum in MSG_INVALID_EXTRUDER
...
SERIAL_ECHO is not very good in printing uint8_t - so cast. to int.
9 years ago
b39b54031b
Fix KEEPALIVE_STATE
...
Add return to NOT_BUSY for M105
Replace WAIT_FOR_USER with PAUSED_FOR_USER
Add Travis test for FILAMENTCHANGEENABLE
9 years ago
32f75749e4
Merge pull request #3117 from Blue-Marlin/thermal-protection
...
Improve the descriptions for THERMAL_PROTECTION
9 years ago
37eaa1406b
follow-up the PR #3180
9 years ago
198d5d56fd
follow-up the PR #3183
9 years ago
4119cef32f
Merge pull request #3180 from clexpert/RCBugFix
...
Czech language specific changes
9 years ago
da94bcfebb
Merge pull request #3184 from thinkyhead/fix_command_injection
...
Patch drain_queued_commands_P
9 years ago
41145e6e81
Patch drain_queued_commands_P
...
Fix a SNAFU that should have been caught in #3012
9 years ago
3ce0c5063f
Merge pull request #3183 from thinkyhead/rc_lcm1602_support
...
Also closes #3181 .
9 years ago
eda95d8bed
Add support for LCM1602 16x2 I2C LCD adapter
9 years ago
59483221d5
Move stepper DAC to a separate file
9 years ago
5d0570cea0
Make digitalPotWrite depend on HAS_DIGIPOTSS
9 years ago
f96bc03081
Add M907-M910 g-codes support for Printrbot Rev. F
9 years ago
6843b78f99
Add support for Printrboard RevF
...
The PrintrBoard Rev F utilizes a mcp4728 DAC to set motor current. Printrbot's implementation utilizes 2 new M-codes to set and write the DAC settings to the DAC EEPROM: `M909` (Read DAC) and `M910` (Write DAC). `M907` is re-used to set value, `M908` for direct control.
The Pins file for the RevF board is included.
9 years ago
98392782ea
Update Configuration.h
9 years ago
daa52124b0
Update language_cz.h
9 years ago
3166aed087
Improve the descriptions for THERMAL_PROTECTION
9 years ago
a02ae36ae8
Include M65 "ABC" parameters in EEPROM
...
Addressing #2773
9 years ago
cf7c444aff
Apply unknown_position_error elsewhere
9 years ago
eda5190581
Check for known position in `M48`
9 years ago
68085ca855
Updated M48 friendly for DELTA
...
Partial implementation with reference to MarlinFirmware/Marlin#3011
9 years ago
6a3529247f
"Homing" as a translatable string
9 years ago
c97c2dcaf7
Use const parameters instead of static casting
...
Alternative fix to #3149
9 years ago
38b0082bf2
Additional tweaks to M42 exit conditions
9 years ago
4bbea5124d
Support for multiple PWM fans
9 years ago
637cc03686
Fix M109 so it won't wait for cooling
...
Addressing issue #2767
9 years ago
3f45a1acf9
Check probes only when deployed
...
Aim: Test probes in update_endstops only when activated
Changes:
Configurations
Add define for FIX_MOUNTED_PROBE to handle the situation where formerly ENDSTOPS_ONLY_FOR_HOMING had to be set, or lowering the nozzle below Z_PROBE_OFFSET_FROM_EXTRUDER could give an "endstop hit" message.
Add define for Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN to indicate a common situation, that we have a probe but it is connected to an endstop pin
Add some comments
Shift some entries to have related things together.
Conditionals.h
We have a probe (HAS_Z_MIN_PROBE) if one of the pins is defined AND one of the probes is defined.
SanityCheck.h
Add some tests if the probe is connected and if we have defined a probe.
stepper.cpp
Changes to test the probe only when it is deployed (z_probe_is_active).
Test update_endstops() when the probe is deployed.
MarlinMain.cpp
a. set and reset z_probe_is_active in deploy_z_probe(), stow_z_probe() and dock_sled()
b. set and reset z_probe_is_active in the case a z-servo is moved to a defined position. The only remaining unhandled servo move is in M280 where we do not end in a defined position. If you want to handle a probe use M401/402
c. skip deploying/stowing when already deployed/stowed in the dedicated deploy/stow functions.
d. Handle the new FIX_MOUNTED_PROBE in parallel to a servo driven probe/endstop.
To do: In another PR. handle all probes in deploy/stow_z_probe.
Sort out SERVO_LEVELING vs. HAS_SERVO_ENDSTOPS.
9 years ago
4634feaeab
Merge pull request #3012 from thinkyhead/fix_command_injection
...
Use a serial line buffer to prevent queue corruption
9 years ago
9bf87aac6a
Merge pull request #3127 from thinkyhead/rc_core_babystepping
...
Implement BABYSTEPPING for COREXY and COREXZ
9 years ago
4ae03df5c2
Merge pull request #3109 from thinkyhead/rc_host_keepalive
...
Provide feedback to hosts when busy
9 years ago
963a92ceda
Patch idle forevermore
9 years ago
7ec7bb31c4
Send a Busy signal to hosts during long processes, wait for input, etc
...
If Marlin is blocking the serial input or command queue for any length
of time (for example more than 2 seconds), it needs to send a message
to serial out to inform the host that it is busy. Marlin should only
send these messages out when busy, and preferably not when trying to
print formatted output.
9 years ago
8d580ea7e8
follow-up the PR #3114
...
follow-up the commit d56c6af24e
9 years ago
d9e1f22682
BABYSTEPPING requires ULTRA_LCD
9 years ago
e5fd43f343
Implement BABYSTEPPING for COREXY and COREXZ
9 years ago
80277cc9c8
drain_queued_commands_P now returns true if there are more
9 years ago
8fe7420310
Use a separate serial line buffer
9 years ago
7d25c107a8
Merge pull request #3149 from esenapaj/patch-1
...
suppress warnings
9 years ago
d56c6af24e
Merge pull request #3114 from thinkyhead/rc_reverse_lcd_menu
...
Option to reverse the click-wheel direction in menus
9 years ago
cc291aeb3c
Move definition of "blink" to main ultralcd file
9 years ago
e7e1866589
Merge pull request #3161 from Alex9779/fix_InitialExtruderDirection
...
Fix initial extruder direction for second/third/fourth extruder if they run inverted to the first
9 years ago
57e82cacc9
Merge pull request #3156 from esenapaj/patch-3
...
Fix CardReader::lsDive()
9 years ago
4338813814
save last extruder and set stepper directions too in case the extruder changed
...
fixes MarlinFirmware/Marlin#3144 and MarlinFirmware/Marlin#3083
9 years ago
8f24475e02
Simplify limiting encoderLine in END_MENU
9 years ago
fbef2f5b61
Implement reverse menu direction in ultralcd.cpp
9 years ago
b8b51d8da8
Add the REVERSE_MENU_DIRECTION option
9 years ago
999a76dbdf
Merge pull request #3157 from esenapaj/patch-4
...
Use variable in lcd_erase_line()
9 years ago
e8fa843c2d
Merge pull request #3164 from epatel/epatel/RCBugFix
...
Fix for #3160 MESH_BED_LEVELING broke correct G1 movement in Z
9 years ago
fc04b587cf
Merge pull request #3147 from thinkyhead/rc_stringify_macro
...
Promote STRINGIFY to macros.h
9 years ago
d7c6fd5c2f
Merge pull request #3146 from thinkyhead/rc_enabled_true_false
...
Support "true" and "false" in the ENABLED macro
9 years ago
cb0dbfa3b5
Fix for #3160 MESH_BED_LEVELING broke correct G1 movement in Z
9 years ago
a15c5d222a
Use variable in lcd_erase_line()
...
lcd_erase_line() is called with argument, but the argument is ignored by lcd_erase_line().
9 years ago
609c0d46d9
Fix CardReader::lsDive()
...
If comparison between signed char(-128 ~ +127) and DIR_NAME_DELETED(uint8_t const 0XE5, it's +229),
it makes incorrect result.
9 years ago
2ef49a9d53
Wrap DEFAULT_Ki, DEFAULT_Kd, PID_dT
...
Addition to #3140
9 years ago
eb8cf29464
Merge pull request #3151 from hydrocat/RCBugFix
...
Uptades the pt-br translation
9 years ago
6e1bc03d3b
Additional wrapping for #3140
9 years ago
cc9968f893
Patch spacing in #3140
9 years ago
1c384930f3
Merge pull request #3140 from thinkyhead/rc_fix_macro_expansion
...
Wrap macros to prevent bad expansions
9 years ago
de2cca73ac
Uptades the pt-br translation
9 years ago
a4314c4907
Use local variable in recalc_delta_settings()
...
diagonal_rod hadn't been used anywhere.
9 years ago
8de7a6f9b1
suppress warnings
9 years ago
9418b4f2f3
Promote STRINGIFY to macros.h
9 years ago
4b648793f2
Use ENABLED with DISABLE_[INACTIVE_][XYZ]
9 years ago
73a59a4e45
Allow ENABLED(b) to work with "true" and "false"
9 years ago
c73f1b2471
Extend stack_overflow_protection for lcd_move_e and _lcd_level_bed
...
Extend stack_overflow_protection for lcd_move_e() and _lcd_level_bed() with
a refined method of 3050.
9 years ago
f4a3efd35e
Merge pull request #3116 from thinkyhead/rc_fix_value_edit_bug
...
Fix value edit click bug
9 years ago
3f5fbbd398
Merge pull request #3124 from jbrazio/bugfix/update-g29-auto-level-bed-topography
...
Update the bed topography output done by G29
9 years ago
c16c47954c
Merge pull request #3141 from esenapaj2/RCBugFix
...
follow-up the PR #3131
9 years ago
30c3a21d1f
Merge pull request #3112 from thinkyhead/rc_support_MAX31855
9 years ago
81d759efb6
Merge pull request #3138 from jbrazio/bugfix/m109-r-could-wait-forever
9 years ago
2179f598bf
Merge pull request #3122 from thinkyhead/rc_group_filament_change
9 years ago
62a9b9902d
Merge pull request #3133 from thinkyhead/rc_machine_uuid_in_m115
9 years ago
f928894c38
Merge pull request #3132 from thinkyhead/rc_heating_failed_err
9 years ago
236a44c83b
follow-up the PR #3131
...
follow-up the commit 7326d63ce0
9 years ago
f9ded2a7c4
Wrap macros to prevent bad expansions
9 years ago
a645860431
All print timer related activity now uses print_job_start(), print_job_timer() or print_job_stop()
9 years ago
1981e53d68
M109 R option if misused could cause a wait-forever situation
9 years ago
7976e29399
Use MACHINE_UUID in M115
...
Addressing #2879 . The M115 report should display `MACHINE_UUID` but it
always displays `UUID`.
9 years ago
81aab828e2
Fix a "Heating failed" error
...
Addressing #3085 . If the target_temperature is set directly it never invokes or disables the timer set in `start_watching_heater`, so after _stopping a print_ or turning off _all heaters_ you could get a “Heating failed” error.
9 years ago
0c48eaf3de
Expose motor current in more configs, disable by default
9 years ago
e8b10d2836
Adding PWM_MOTOR_CURRENT flag to help expose PWM_MOTOR_CURRENTS in Configuration_adv.h similar to DIGIPOT_MOTOR_CURRENT
9 years ago
4d4a842cfb
Update the bed topography output done by G29
9 years ago
89838cdb10
Move step macros to stepper_indirection.h
9 years ago
793cd0ae3b
Clean up the code a bit
9 years ago
27f244ba2c
Support MAX31855 as Temperature Sensor -3
9 years ago
ce639b8b03
Group FILAMENT_SENSOR options together
9 years ago
3fd31976c3
Reduce code in stepper.cpp with macros
9 years ago
b45a0c4c60
Fix bugs in edit submenus so they return to origin
...
Expected behavior: After editing a value the menu should return to the
previous place with the edited item selected.
Actual behavior: Either the top (back) item from the previous screen is
selected, or the menu jumps up another level.
Solution: Pass the correct arguments to `lcd_goto_menu` on click when
editing a value.
9 years ago
986b508ff7
Print timer now stops when it sees the last extruder temperature being shutdown
9 years ago
fd5414c6ea
Z_RAISE_BEFORE_HOMING -> MIN_Z_HEIGHT_FOR_HOMING
...
rebased
corrected spelling
changed to #elif for error
Still with MIN_Z_HEIGHT_FOR_HOMING but con be done with (folder wide) search-replace when we have a better name.
9 years ago
b7928a000a
Merge pull request #3108 from AnHardt/M110+
...
M110 and M29 rework
9 years ago
5cba0b4187
Merge pull request #3111 from thinkyhead/rc_drop_old_condition
...
Drop obsolete test for leading "N"
9 years ago
302d1bfbc4
Drop obsolete test for leading "N"
9 years ago
37b857e8ec
M110 ang M29 rework
...
Add 'ok' output for G29 actually closing the file.
Handle M110 when received without linenumber/checksumm.
9 years ago
29e09c7c3e
update example configurations
...
update old comments
update or delete deprecated definitions
complement forgotten updates
adjust spacing
some cosmetic changes
9 years ago
fac85f6fa1
Merge pull request #3102 from jbrazio/bugfix-g28-multiple-z-movements
...
Bugfix: G28 was lifting Z-axis multiple times
9 years ago
642e3699ce
Z-axis was being lift multiple times if Z_SAFE_HOMING was enabled and Z_RAISE_BEFORE_HOMING was greater than zero
9 years ago
501f63802a
Merge pull request #3077 from Blue-Marlin/watchdogreset-in-kill
...
Add Watchdog timer reset in kill()
9 years ago
1002eb67c8
Update name of st_get_axis_position_mm in stepper.h
9 years ago
7dde761aa6
Fix MELZI_MAKR3D to use correct motherboard
...
Signed-off-by: Jaroslav Škarvada <jskarvad@redhat.com>
9 years ago
eafbc5e0cc
Add AJ4P pins and fix RAMBO pins
9 years ago
cf792fd8d8
Update configurations to use RAMPS 1.4
9 years ago
cacf04f8a7
Base RAMPS-like boards on RAMPS 1.4
9 years ago
50e3482e0a
Handle RAMPS 1.3 as the special case
9 years ago
679be3294f
Rename RAMPS 1.3 pins for RAMPS 1.4
9 years ago
f18d3f451a
Limit LCD move_to_x/y coordinates for deltas
...
Related to MarlinFirmware/MarlinDev#270
9 years ago
988332c67a
Cosmetic tweaks from dev
9 years ago
2690d8568e
DOGLCD width/height in Conditionals.h
9 years ago
614febaaf3
Fix acceleration limits
...
See: https://github.com/Ultimaker/Marlin/pull/7
9 years ago
13ef12ad3f
Fix power calculations
...
As suggested by @max-pau in #3073 - #3074
9 years ago
e2b022cce2
Include #3053
9 years ago
5cba0210f2
Small patch to Z_SAFE_HOMING comment
9 years ago
6165fd41a5
Fix Hephestos 2 and other configs
9 years ago
71718d888a
Fix typos in check_axes_activity
9 years ago
83795d3e63
deleted double used comments
9 years ago
143ad74db7
Update PROBE_OFFSET_FROM_EXTRUDER comment section in all example config
...
files.
9 years ago
b0f5ba0232
Update the PROBE_OFFSET_FROM_EXTRUDE comment section
...
This changes have being discussed at MarlinFirmware/Marlin#2849 .
9 years ago
02b131b552
Replaced stock BQ PID values with fine tuned ones generated using M303
9 years ago
45dc8a51f3
Added readme file for bqh2 and disabled the SLOWDOWN config flag
9 years ago
6a21180bd4
Implemented BQ ZUM Mega 3D board layout as an override to RAMPS 1.3
9 years ago
b18816fcbf
Fine tuned XYJERK.
...
Disallowed the Z_PROBE_OFFSET_RANGE_MAX to be greater than zero.
9 years ago
be83036212
Applying suggestions by @thinkyhead at MarlinFirmware/Marlin#3049 .
...
- Remove the forced activation of SDSUPPORT, I guess people may use the ZUM
3D board and not the LCD module.
- Fixed the tab issue within boards.h file.
9 years ago
b82d91eca6
Added configuration example for the BQ Hephestos 2 3D printer.
...
Added support for BQ ZUM Mega 3D board and stock Hephestos 2 thermistor.
9 years ago
45bcc43e48
Don't override SOURCE_CODE_URL in Default_Version.h
...
- Defining `SOURCE_CODE_URL` in `Default_Version.h` overrides it
elsewhere. So don’t define it there.
- Also fix up `language.h` so no `#undef` will be needed.
9 years ago
ef68c1910c
Check that the temperature is close to target
9 years ago
ea9fd1200b
Fix M109 so it won't wait for cooling
...
Addressing issue #2767
9 years ago
e4945b30d2
sbi and cbi are deprecated
9 years ago
ff13070b59
Use _BV macros, patch up others
9 years ago
209f5f21e0
Use macros where possible
...
Apply `constrain`, `NOMORE`, `NOLESS` and `CRITICAL_SECTION` macros
wherever possible.
9 years ago
c8f76bb8aa
Create BITSET/BITCLR macros
9 years ago
adc25db8c4
Merge pull request #3005 from thinkyhead/rcbugfix_eeprom
...
Fix layout descr. in configuration_store.cpp
9 years ago
e7cf85b922
Merge pull request #3013 from thinkyhead/esenapaj-patch-1
...
Enhanced #3010 - formal Mesh/Manual dependency
9 years ago
6e64895c30
Merge pull request #3001 from AlwaysTinkering/RCBugFix
...
Rc bug fix - Fix for issue #2931
9 years ago
34b8b9f0f5
Merge pull request #2995 from thinkyhead/rcbugfix_corexy_corexz
...
Add CORE support to st_get_position_mm (and elsewhere)
9 years ago
1e20949afb
Merge pull request #3092 from thinkyhead/rc_2860_printrbot_lcd
...
Fix Printrboard with LCD (redo)
9 years ago
f5972c4d2c
Merge pull request #2994 from AnHardt/Inerrup-save-serial
...
Interrupt safe serial --- Guard against non-atomic variable changes from interrupt routines
9 years ago
3a3d358df9
Fix Printrboard with LCD (redo)
...
Based on #2860 - rebased for RCBugFix
9 years ago
eb85342fd9
Merge pull request #2989 from AnHardt/fix2661
...
Pre home display - Stepper release
9 years ago
14f3ca1b2e
Merge pull request #2978 from thinkyhead/tool_offset_abl_rcbugfix
...
Apply bed leveling matrix when switching extruders
9 years ago
91fcdc2b99
Merge pull request #3090 from thinkyhead/rc_spelling
...
Various minor spelling corrections
9 years ago
772460a7b8
Various minor spelling corrections
...
Redo of #2939 rebased against RCBugFix
9 years ago
0fb507a75d
correct raise_z_for_servo
9 years ago
04a0d45c22
Merge pull request #2821 from MarlinFirmware/ReinitializeDisplay
...
Fix status LEDs update when reinitializing the display
9 years ago
b4e5e0f11d
Add Watchdog reset in kill()
...
Add watchdog reset in the kill loop to simplify recovering.
9 years ago
547d35a921
Merge pull request #3067 from Blue-Marlin/ALARM_PIN
...
Remove unused ALARM_PIN
9 years ago
79778d46d9
Merge pull request #3066 from Blue-Marlin/Fix-disable_all_heaters()
...
Fix disable_all_heaters() for MAX6675
9 years ago
a68228bf55
Remove unused ALARM_PIN
...
Remove unused ALARM_PIN from all the Configuration.h's
9 years ago
9eb4aceee4
Merge pull request #2986 from thinkyhead/enable_watchdog
...
Enable USE_WATCHDOG by default
9 years ago
0631541166
Fix disable_all_heaters() for MAX6675
9 years ago
222d13d5ed
Merge pull request #3051 from thinkyhead/rcbugfix_dual_axis_offset
...
Code cleanup in gcode_T
9 years ago
186629aee8
Merge pull request #3057 from jbrazio/3034-z_raise_after_probing_fix
...
Fix Z_RAISE_AFTER_PROBING for non DELTA printers
9 years ago
a42fb35c56
Merge pull request #3050 from Blue-Marlin/fix-1166
...
Temporary workaround for stack overflow
9 years ago
67e15aac3d
As pointed out by @Blue-Marlin the previous code would raise the Z axis
...
twice for a servo based probe.
9 years ago
17cc2a9663
Z_RAISE_AFTER_PROBING value was being ignored by Marlin because
...
raise_z_after_probing() was only called if the printer type was set to a
DELTA or if the printer had a docking sled for the probe.
9 years ago
252f4a75cd
Merge pull request #3043 from oxivanisher/RCBugFix
...
Example configuration for Kossel XL
9 years ago
fd1243c184
Merge pull request #3052 from thinkyhead/rc_fix_m145_eeprom_output
...
Fix "M145" output in M503 report
9 years ago
0bc648353f
Merge pull request #3031 from tnw513/RCBugFix
...
Fix board type for Hephestos: RAMPS 1.4
9 years ago
f27c2b6b4b
Reimplement #2892
...
Include #2892 to fix the isHeating symbol in the extruder graphics
9 years ago
615bec2329
Activate warning about possible reduced accuracy by default
...
Renamed `WARN_REDUCED_ACCURACY` to `DISABLE_REDUCED_ACCURACY_WARNING`
Changed the condition for blinking from
```
#if ENABLED(WARN_REDUCED_ACCURACY)
```
to
```
#if DISABLED(DISABLE_REDUCED_ACCURACY_WARNING)
```
9 years ago
1c889cd303
Refresh previous_cmd_ms during run_z_probe()
...
Refresh previous_cmd_ms during run_z_probe() to prevent:
stepper shutdown for expired DEFAULT_STEPPER_DEACTIVE_TIME
and extrudes for expired EXTRUDER_RUNOUT_SECONDS
(https://github.com/MarlinFirmware/MarlinDev/issues/238 )
9 years ago
4b02f33e69
Distribute config-changes to the other configurations
9 years ago
be24fdacea
The same changes to the axis-letters now for the char-displays
...
Exactly the same - copy/paste.
9 years ago
5b0f659355
Changes for graphics displays
...
Replaced displaying "---" instead of the value of a coordinate when
unhomed or with reduced precision
with blinking the coordinate-prefix-character ('X','Y','Z').
For "unhomed" a '?' is shown every second second - until that axis is
homed. The value displayed is, as before the "---" where displayed, the
relative to the reset position coordinate value.
When the axis stepper was disabled, now we can display a hint on that,
by showing a blinking ' ' instead of the axis letter, when
WARN_REDUCED_ACCURACY is defined.
I suppose the code itself is here the better documentation.
A '+/-' character is in non of our charsets so i decided for a '?' for
now to reduce the work.
There is no additional space on the displays one could use to display
the information, so replacing something is the only option. As the axis
letters are totally redundant with their positions on the display they
contain the least information.
So my decision was to overwrite them.
9 years ago
32ae9f9ab7
Fix stepper shutdown during waiting for temperatures
...
In the wait loops of M109 M190 idle() is called, what checks
stepper_inactive_time against previous_cmd_ms.
Because we can be several minutes inside the loop, resetting
previous_cmd_ms only outside the loop caused stepper shutdowns.
The name of previous_cmd_ms does not really reflect its use. It's set
not only when a new command was received or executed but also in many of
the movement routines. For that the little extension of using it during
the wait will (hopefully) not hurt.
# Conflicts:
# Marlin/Configuration_adv.h
9 years ago
b6e69e71ce
Make stepper shutdown after inactivity dependent
...
Make stepper shutdown after inactivity dependent on a new set of
#defines.
DISABLE_INACTIV_X
DISABLE_INACTIV_Y
DISABLE_INACTIV_Z
DISABLE_INACTIV_E
And make exemplaric Configuration.
Names can be discussed.
This makes the disabling of the steppers independent from the DISABLE_?
settings witch shut down the steppers immediately.
9 years ago
051325ccd7
Introduce axis_homed
...
Introduce additional variable axis_homed to replace axix_known_position
when the coordinate display should indicate the axis is not homed.
This is to distinguish between "not homed" and "inexact position possible
because stepper was disabled".
# Conflicts:
# Marlin/ultralcd_implementation_hitachi_HD44780.h
solved
9 years ago
e736779d7e
blink for char-lcds
...
Implement and test blinking for char-lcds
# Conflicts:
# Marlin/ultralcd_implementation_hitachi_HD44780.h
solved
9 years ago
7253a1971d
Fix "M145" output in M503 report
9 years ago
d118e3f985
Merge pull request #3044 from thinkyhead/rc_gcode_spaces
...
Fix GCode handling of spaces between command letter and first digit
9 years ago
100271e6ac
minor cleanup in gcode_T
9 years ago
fd9e94e5a4
Fix crashes when the Z axis is moved via LCD
...
Fix crashes when the Z axis is moved via LCD
by calling `plan_buffer_line` only when there is enough room in the
planner buffer, to avoid endless recursion.
A brief description about what went wrong is in #1166
9 years ago
8dccd5a7ea
Merge pull request #3018 from CONSULitAS/RCBugFix_K8200_backinsync
...
K8200: sample config back in sync
9 years ago
6a4f06d35d
Fix GCode handling of spaces between command letter and first digit
9 years ago
68eae2b5a8
added kossel xl example configuration
9 years ago
eb5817675d
Fix board type: RAMPS 1.4
9 years ago
cb88fdd242
Protect MarlinSerial against interrupts
...
Protect MarlinSerial against interrupts
by shielding the CRITICAL_SECTIONs
Now with a test if RX_BUFFER_SIZE is in the required range.
Code in peek() and read() is now optimized for readability and showing the similarity between the two.
Maybe a bit overprotected in checkRx() and store_char(), but now some days without detected errors from this source.
9 years ago
dc0f41868e
Make rx tail/head atomic
9 years ago
ea8409ad5d
Fix: current_command_args contains command
...
@thinkyhead
Hi Scott,
your code from a0f362c@thinkyhead is great, but you forgot to skip the
command.
Symptom `M117 Test`shows `M117 Test` on LCD instead of `Test`.
see also
https://github.com/MarlinFirmware/Marlin/commit/a0f362c735401ebbcd95de3f
6f8e3c2f17ecc770 lines 941, 2851 and so on
Greetings and welcome back
Jochen
9 years ago
9a3408e58f
Merge pull request #3024 from thinkyhead/rc_remove_steps_mm_e
...
Remove obsolete STEPS_MM_E setting
9 years ago
1093c780c8
Remove obsolete STEPS_MM_E setting
9 years ago
a4fe6a45ae
K8200: sample config back in sync
...
* Configuration.h:
* updated header comment
* new UUID feature used
* sync to default config
* typos fixed
* changes better documented
* reflect change in SDSUPPORT feature
* Configuration_adv.h
* updated header comment
* thermal protection tuned to work with K8200
* homing tuned
* sync to default config
* typos fixed
* changes better documented
* reflect change in LCD features
* use long filenames
* use Watchdog
* use Babystepping
* use Auto Filament Change
9 years ago
c2e5c6c12c
Nest Manual Bed Leveling options
...
This formalizes the dependency of MANUAL_BED_LEVELING on
MESH_BED_LEVELING
9 years ago
042a6a0a37
Extend existing MESH_BED_LEVELING test
9 years ago
08b3147791
sanity check for MANUAL_BED_LEVELING
9 years ago
9f8e6dce20
Merge pull request #2942 from esenapaj/esenapaj-patch-2
...
more suitable display format for delta printer
9 years ago
e1beaf61eb
Merge pull request #2985 from AnHardt/adv-ok
...
Repair N in ADVANCED_OK
9 years ago
34cde1b77c
Merge pull request #14 from MarlinFirmware/RCBugFix
...
Rc bug fix
9 years ago
f00ca3fd89
Fix layout descr. in configuration_store.cpp
9 years ago
0c9db67273
Merge pull request #2983 from AnHardt/ok-echo
...
Replace the "ok" in M280, M301, M304, M851 with output not including …
9 years ago
fbfbc5e330
Enable USE_WATCHDOG by default
9 years ago
d4e7c2d694
Merge pull request #2976 from thinkyhead/drop_configurator
...
Drop the experimental Configurator
9 years ago
9df0e0e0cc
Merge pull request #2974 from thinkyhead/sanitycheck_spi_speed
...
Sanity-check deprecated options replaced by SPI_SPEED
9 years ago
3e2473e695
Merge pull request #2988 from thinkyhead/z2_more_extruders
...
Use next open E connector for Y2/Z2
9 years ago
8eaba020fb
Merge pull request #2973 from thinkyhead/fix_splash_url
...
Remove references to marlinfirmware.org
9 years ago
438a87eba8
Sanity check deprecated SDSLOW, SDEXTRASLOW
9 years ago
b19b272172
Update configurations with SPI_SPEED
...
- Include aligned comment about new SDSUPPORT behavior
9 years ago
7f30f85602
Merge pull request #2987 from thinkyhead/gcode_allow_no_initial_space
...
Fix handling of spaces in GCode
9 years ago
b81d3b83cf
Drop the experimental Configurator
...
Development moved to https://github.com/thinkyhead/MarlinConfigurator
9 years ago
be691b51f1
Remove references to marlinfirmware.org
...
The domain is gone and doesn’t redirect, so for now show no URL on the boot screen.
9 years ago
f3f58bd619
Merge pull request #2992 from thinkyhead/rc_rename_fpos_t
...
Rename fpos_t to avoid libc conflict
9 years ago
83ffc9eb4f
Show raw steps in M114
...
This is a proposed change. This section of M114 output is a debug
extension according to RepRap wiki.
9 years ago
373e8a1ad4
Fixes for COREXY and COREXZ coordinates
9 years ago
31656e68bc
Fix for homing X and Y before raising Z when Z_SAFE_HOMING is set.
9 years ago
8ea55323d8
Fix for not raising Z before homing X and Y
9 years ago
b83e472bd3
Rename fpos_t to avoid libc conflict
9 years ago
68457ee903
For Dual Y/Z use the next available extruder pins
9 years ago
711e5db19a
Tweak comment in process_next_command
9 years ago
400e9329be
Allow spaces after a code letter
9 years ago
cdcb80f3c5
Allow no-space after initial command
...
Addresses issue #2715
9 years ago
6f473f7fc6
Repair N in ADVANCED_OK
...
Send the correct line number.
If no N was in the command - non't send an N.
9 years ago
efbd705eda
Replace the "ok" in M280, M301, M304, M851 with output not including an "ok"
...
Replace the "ok" in M280, M301, M304, M851 with output not including an "ok"
to avoid senting two "ok"s for a single g-code.
Doing the same for M105 would break the input filters of the hosts.
For M105 the other "ok" is omitted.
9 years ago
8e66028d25
Apply the ABL rotation matrix to the extruder offset.
9 years ago
ab5aa3fc92
Merge pull request #5 from MarlinFirmware/RCBugFix
...
Rc bug fix
9 years ago
27d918d836
Merge pull request #4 from MarlinFirmware/RCBugFix
...
Rc bug fix
9 years ago
159ff94afd
Remove obsolete HEATER_BED_DUTY_CYCLE_DIVIDER #2977
9 years ago
1270fbfd38
Using SET_INPUT instead of pinMode
9 years ago
b58083b0fa
Getting rid of SDEXTRASLOW, SDSLOW variables.
9 years ago
1833049b8a
reusing millis()
9 years ago
1b7c443628
Adding SDULTRASLOW variable.
...
Instead of changing SDEXTRASLOW variable to a slower speed, the new
SDULTRASLOW is used for rigidbot panel.
9 years ago
6f9e9c0e4f
Cleaning up, getting rid of the fake encoder count variable.
9 years ago
becbfe1065
Fixing Rigidbot LCD Panel Support
9 years ago
4882a7eded
more suitable display format for delta printer
9 years ago
d7272e3f36
Merge pull request #3 from MarlinFirmware/RCBugFix
...
Rc bug fix
9 years ago
62bad1b60f
Merge pull request #2848 from japzi/RCBugFix
...
Fixing Rigidbot LCD Panel Support
9 years ago
59d345a3dd
Update Configuration.h
9 years ago
b8f0c8a4c7
Update Configuration.h
9 years ago
df0d599c79
Update Configuration.h
9 years ago
a366697649
Update Configuration.h
9 years ago
7c94c83765
Repair formula mangled by PR#1319 in Jan 2015
9 years ago
2932602643
Update stepper.cpp
...
Forgot Z2_MIN_PIN
9 years ago
06555febdd
Using SET_INPUT instead of pinMode
9 years ago
8d2aa2368d
Update Configuration_adv.h
9 years ago
0de5fcad0a
Update Configuration_adv.h
9 years ago
1403b9acc0
Update Configuration_adv.h
9 years ago
5cf1c38ea1
Update Configuration_adv.h
9 years ago
04ab61bf40
Update Configuration_adv.h
9 years ago
39c62fbd6f
Update Configuration_adv.h
9 years ago
efcb769003
Update Configuration_adv.h
9 years ago
992fbb831d
Update Configuration_adv.h
9 years ago
5ee6fe6385
Update Configuration_adv.h
9 years ago
056daf00fc
Update Configuration_adv.h
9 years ago
71aafb79a0
Update Configuration_adv.h
9 years ago
2c9e0415c7
Getting rid of SDEXTRASLOW, SDSLOW variables.
9 years ago
a64bcd53e9
reusing millis()
9 years ago
e6cc232184
Adding SDULTRASLOW variable.
...
Instead of changing SDEXTRASLOW variable to a slower speed, the new
SDULTRASLOW is used for rigidbot panel.
9 years ago
83c4131ba3
Cleaning up, getting rid of the fake encoder count variable.
9 years ago
5eeea2f611
Fixing Rigidbot LCD Panel Support
9 years ago
f6950acb8e
Residual unused variable — Backport
9 years ago
7a670e3911
Improve planner & stepper PR #263
9 years ago
58658c9279
Call the probe pin a probe pin and not a min endstop
9 years ago
0fa3bac8ee
If unused, just don’t define it.
9 years ago
3b2973da6a
Prepare Ramps for user redefinition
9 years ago
1635613c25
Backport cosmetic
9 years ago
0b429461d5
Back port Cosmetic changes
9 years ago
0cebe85e65
Clean up spacing and duplicate entries
...
• Removing trailing whitespace
• Adjusting indention for better readability
• Removing duplicated entries
9 years ago
e7b40bbe98
Change link to U8glib source
9 years ago
e2da2b4105
Back port language translation
9 years ago
4f314afaf0
Allow Thermistor #12 to be used on hotends also
...
//100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed)
Caveat Emptor —-
I’m not sure that this really makes sense,
but why keep someone from using it?
9 years ago
60d5658da8
Revert nozzle_bed_fan_menu_items
...
For some reason that I cannot determine, using a sub-function causes
the Tune sub-menu to act strangely, yet replacing the function call
with its code content works perfectly.
9 years ago
57da1b8497
Host parseble output for M109, M190 and M303
...
Make the output of M105 more similar to Repetier.
Make the text-print pert of M105 an extra function to make it reusable. `print_heaterstates()`
Use `print_heaterstates()` in M019, M190 and M303
9 years ago
fcceb98191
Unglobalize no_wait_for_cooling
9 years ago
78a347a01a
change nx, ny, nz and ne from float to long
...
st_set_position takes long
```void st_set_position(const long& x, const long& y, const long& z, const long& e)```
9 years ago
6d691aceee
change dx, dy, dz and de from float to long
...
anything is long, we don't need float there
9 years ago
6bfcb74c25
The probe stowing coordinates have changed
9 years ago
0fbfb22506
Renaming delta speeds (PR2824)
...
dx -> dsx
dy -> dsy
dz -> dsz
de -> dse
9 years ago
8d1eeff021
Fix status LEDs update when reinitializing the display
...
Fix status LEDs update when reinitializing the display
By using the regular update function during init.
Fixing #2683
9 years ago
5a54204f72
Marlin 1.1.0 Release Candidate 3 - 01 December 2015
9 years ago
bb4efcf603
Handle temp callbacks when THERMAL_PROTECTION_HOTENDS is not defined
...
by alternate definition for the callback macros
9 years ago
96d0d04b8f
Update LCD buttons less frequently
...
Move slow_buttons_update into the LCD_UPDATE_INTERVAL block
lcd_implementation_read_slow_buttons() will then be executed ~10 times a
second.
9 years ago
e293ea57f0
Unbalanced brackets in setPwmFrequency
...
This is a back port of the correct in issue #248
9 years ago
c956b52c4a
Babystep Multiplier
...
Analog to https://github.com/MarlinFirmware/MarlinDev/pull/250 by
@RicardoGA
Restore the Babystep Multiplicator functionality and now it's available
for X/Y/Z
9 years ago
956418c674
Kc is also a multi-PID parameter
9 years ago
33addc52a1
Suppress Z_MIN_PROBE_REPEATABILITY_TEST for DELTA and SCARA configurations (PR#2747)
...
For now Z_MIN_PROBE_REPEATABILITY_TEST is not possible for DELTA or SCARA
configurations.
This PR comments the feature out, where it is commented in by default.
9 years ago
8da2e98985
Split RAMPS 1.3 an 1.4 (PR#2741)
...
because of hardware differences on the SERVO0_PIN
9 years ago
be7167ed97
Change XY formatting on LCD (PR#2740)
...
According to #123 negative values for XY at or below -100 are displaying incorrectly, dropping the first digit. Deltas can easily have XY values in this range. This PR adds a function to display floats/ints formatted like `_123`, `-123`, `_-12`, or `__-1` as appropriate and applies it to the XY coordinates on Hitachi displays. It also moves the Z value to the right to be consistent with the XY formatting.
9 years ago
e7099ea597
Fix Portuguese (Portugal) strings (PR#2700)
...
Align strings with release
9 years ago
754b13d8fe
Patch issue #2315
9 years ago
dbd4c17096
Init Kp, Ki, Kd to 0
9 years ago
644c376e84
Use binary OR with endstop bits
9 years ago
54a39d8c1a
Use a ternary in qr_solve.cpp
9 years ago
17c23bbaf3
Shorten gcode_M221 yet function the same
9 years ago
c0e791dbe9
Only look for "N" line number as first parameter
9 years ago
b4af4441c5
Clean up watchdog impl.
9 years ago
8f16563bbd
Use "defined" with LCD_PIN_BL and LCD_PIN_RESET
9 years ago
6fa7e24af3
Use "UNUSED" to squash compiler warnings
9 years ago
d5b7c595ae
Use static locals in utf_mapper.h
9 years ago
9bdab4f3a8
Clean up "else" and other spacing
9 years ago
9b23490f01
Clean up spacing in configs
9 years ago
c6c37abd41
Update language_kana.h
9 years ago
c24045475a
Update language_kana_utf8.h
9 years ago
25d636c9e0
Compiler issues (PR#2696)
9 years ago
47401ec97b
MSG_EXTRUDER_SWITCHED_OFF was renamed to MSG_REDUNDANCY
...
in language.h, but was not renamed here. If TEMP_SENSOR_1 is enabled as redundant then
an error is thrown that MSG_EXTRUDER_SWITCHED_OFF is not defined.
Originaly by @12dstring
9 years ago
ba6a243197
DEBUG message has no parameter (PR#2671)
9 years ago
0c7f7ebcfb
Styling adjustments (PR#2668 & PR#2670)
...
Keep "astyled" reformatting
9 years ago
b5fb7075b9
Galician (gl) language.
9 years ago
7b4bdc0203
DUAL_X_CARRIAGE motor enabling
...
As noted by @darkjavi et.al. in #103 , the E1 motor was not being enabled in planner.cpp when using DUAL_X_CARRIAGE. This patch enables and disables E1 as it should.
9 years ago
91b5156b3e
Marlin 1.1.0 Release Candidate 2 - 29 September 2015
9 years ago
03f0edb57e
Fix high LCD status screen update frequency (PR#2655)
9 years ago
0ad25c6665
Hint for changed behaviour of SDSUPPORT
9 years ago
e01f5e1ef7
Cleanup
9 years ago
5e36b64635
SDEXTRASLOW for some SD card readers (PR#176)
...
Add SDEXTRASLOW which runs the SD card at SPI_QUARTER_SPEED. Quarter speed is needed for RIGIDBOT_PANEL
9 years ago
5d65a36dee
Give lcd_sd_status an UNKNOWN state (PR#180)
9 years ago
0f149ea0c6
LCD home button causes repeated homing (PR#175)
...
Fix: increased debounce delay.
9 years ago
b825567e0f
Drop www. from marlinfirmware.org (PR#175)
9 years ago
db27e67580
Apply PID_ADD_EXTRUSION_RATE to extras
9 years ago
bc50db9cf6
Implement PID_ADD_EXTRUSION_RATE
9 years ago
cffb2d457e
Cleanup file formatting
9 years ago
7ac7ddbf20
Show nozzles, heaters, and extruders numbered 1-4
9 years ago
5bc480fee8
Fix Move E menu items
9 years ago
fc882c34a3
Init lcd_sd_status as false to force lcd_update test
...
Replaces #145 which is way out of date
9 years ago
e27dd5c22d
Conditionalize functions that rely on SDSUPPORT
9 years ago
fabf3ae4a0
Add final Z raise after Delta probe
9 years ago
8c768a76a2
Create language_cz.h
...
Czech language translation.
9 years ago
5b9010965d
Update language.h
...
Added comment for Czech language (associated with file language_cz.h).
9 years ago
89fb778684
Fix up probe pin define and test
9 years ago
558665cd90
Constrain Tune > Nozzle/Flow menu items
9 years ago
9f462f0cf5
Hack to address stuttering caused by ISR not finishing in time
...
(PR #138 )
When the ISR does not finish in time, the timer will
wrap in the computation of the next interrupt time.
This hack replaces the correct (past) time with a time not far in the future.
9 years ago
8b3d63c423
Unify Delta XYZ homing rates
...
As noted in #130 allen key probe stow rate is based on homing rates,
but homing rates were left out of most delta configs. This unifies the
XYZ homing rates and applies the unified rates to allen key movements.
9 years ago
7c72b57313
Unify manual feedrate and Fix LCD MANUAL_FEEDRATE (PR#128)
...
As noted by @o-lampe at https://github.com/MarlinFirmware/MarlinDev/issues/114#issuecomment-136757614 the `MANUAL_FEEDRATE` for Delta Z should be the same as XY.
9 years ago
f690b82343
Remove extra MAX_FREQ_TIME define (PR#148)
9 years ago
a4c78ae786
Add E1 pins to SENSITIVE_PINS for Dual Y or Dual Z
9 years ago
a39fadf876
Update kossel-pro example config (again?)
9 years ago
34e0a8d848
Move Y2 and Z2 pins defines to pins.h
9 years ago
28599c51c7
Wrap Dual Y options in a conditional
9 years ago
11a065c0ca
Remove Z2 pins overrides from Configuration_adv.h
9 years ago
f7f6b5faae
Fix lcd_move_e compile error (PR#143)
...
Fix a compile error introduced in #98
9 years ago
2b30e8ac99
Conditionals for ULTIPANEL without SDSUPPORT
9 years ago
7c7a4051fe
Disable SDSUPPORT by default
...
As noted in #133 you can’t disable `SDSUPPORT` with `MAKRPANEL`,
`PANEL_ONE`, `MINIPANEL`, or `ULTIPANEL`. This patch makes it possible
to disable `SDSUPPORT` on these controllers and then disables it by
default.
Users of these controllers will now need to enable `SDSUPPORT` in their
configurations as others currently do.
9 years ago
b23d765991
Added Extrude From Multiple Extruders from LCD feature
9 years ago
8347a9d6e4
Fix HOMING_BUMP_DIVISOR for deltas configuration
...
* Re-bump speed divisor should be the same for delta printer.
9 years ago
703df2cb6c
Fix error message for probe region sanity check
9 years ago
4c8330c15c
Trim Adjustments for Delta Configurations
9 years ago
962120d1d2
Fix spacing in some conditional blocks
9 years ago
20b4772155
Create DEBUG_LEVELING_FEATURE
9 years ago
194f98ff95
Debug messages for homing and leveling
9 years ago
6292d9e815
Rename ENABLE_AUTO_BED_LEVELING
...
With the introduction of the #if ENABLED(…)
reads better than
9 years ago
91fd66ffba
add Lulzbot TAZ4 example configuration (PR#104)
9 years ago
7a275773ee
remove colon in utf_mapper.h (PR#106)
9 years ago
6b4b6fa315
update for newest version of U8glib_Arduino
9 years ago
9897a9147c
Update ABL comments (PR#95)
...
* Updates the auto bed leveling comments ONLY.
* Renames "Z probe" word usage in //comments and #errors properly.
9 years ago
a7822e3ff7
Some renaming of Z_PROBE to Z_MIN_PROBE (PR#91)
...
* Fix a couple of renames omission and macro expansion errors.
9 years ago
ad90e851b3
Use a small unsigned integer type
9 years ago
29b456ae07
Suppress some compiler warnings
9 years ago
23d742bf06
Don't free the stack array plane_equation_coefficients (PR#83)
9 years ago
e3b1e08777
Patch G30 to use raise_z_for_servo (PR#73)
9 years ago
a1eb90d5c0
Save another 30 bytes in gcode_SET_Z_PROBE_OFFSET
9 years ago
91122277f4
Reduce gcode_SET_Z_PROBE_OFFSET by 88 bytes
9 years ago
5707a2c3d5
indexindexIntoAB is only vald for !DELTA
9 years ago
d8860f9ad9
Alway end at the same point
...
Always end at [RIGHT_PROBE_BED_POSITION, BACK_PROBE_BED_POSITION]
Regardles the evennes of auto_bed_leveling_grid_points.
9 years ago
4ca8f4a9a7
Always zigzag
...
Use the shortest way between probing-points.
9 years ago
3d23424121
Add array indexIntoAB[xx][yy]
...
and use it.
9 years ago
e2d69f66b2
Make Z_PROBE a Z_MIN_PROBE (PR#65)
...
Currently we use the probe exclusively as a device to find the build platform(bed).
For the currently supported setups this means, we use it as a additional min-endstop.
A triggered when not deployed probe disturbs the homing process for max-endstops.
Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE
Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP
Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST
Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP
Adjust comments accordingly
Remove Z_MAX check for the probe in update_endstops().
Using an delta related idea of @clefranc from #61 ,
extended to the general change for all setups.
Tested with Prusa i3, max-z-endstop and permanently triggered z-probe.
Worked for @clefranc's delta.
9 years ago
6a6e863a47
Resolve #2581 by adding a missed ';' (PR#67)
9 years ago
e09ff79635
Update pins_RAMPS_13.h (PR#64)
...
Now all ramps configuration can enable Filament sensor not only EEB
9 years ago
e6aed7bb4e
Update thermistortables for Hisens Thermistor (PR#2588)
9 years ago
9d8cc24abf
Continue from the line following the M999 (PR#60)
...
If the printer is going to accept the M999,
then it should continue from that line number.
9 years ago
f3ab1dba54
Z babystepping for coreXY (PR#47)
...
only X and Y were not implemented
9 years ago
35afea1c0e
Restore test
...
PR#2572 Changed this because of faulty Boolean Logic
NOT(A OR (NOT B) OR (NOT C)) !=
(NOT A) AND ((NOT B) OR C))
Besides, the compiler should be smart enough to
optimize this without help from the programmer
9 years ago
6af75f4b5d
Squish down deprecated tests in sanity check
9 years ago
edeb58288e
Use PIN_EXISTS in sanity check
9 years ago
c30b7693e0
Clean up RUMBA pins conditions
9 years ago
46453905d6
Apply remaining ENABLED/DISABLED conditionals
9 years ago
b227d8c128
Supply a VERSION in a short form for displays
...
The long descriptor will still be available in M115
9 years ago
cd7828a928
This will be the 1.1.0 Release rather than 1.0.3
9 years ago
4e2f5618c1
Pick up Default_version when needed
9 years ago
329acc852e
Canonize Option flag USE_AUTOMATIC_VERSION
9 years ago
5a11d32a85
Move deprecation test to SanityCheck.h
9 years ago
7bb7a52940
Bring config up-to-date
9 years ago
244ea2014a
Boot-screen for text-displays improvements
...
Centred the logo for 16x4 and 20 x4.
Moved version to the bottom line
Code shrink to 704 bytes.
9 years ago
80f2a20842
Enable bootscreen in all Configurations
9 years ago
2684d061ed
Scroll too long strings on bootscreen
9 years ago
4f46df5dab
Make bootscreen configurable for the graphic displays
...
Saves about 473 byte of progmem and 28 bytes of RAM.
9 years ago
09571b7753
Boot-screen for the character displays
...
Uses about 488 byte of progmem and 32 byte of RAM.
For that configurable.
9 years ago
866efc14fe
Add Danish translations
9 years ago
267f3479d7
Adjust spacing in pins_RAMPS_13.h
9 years ago
56702e7bb9
Define servo pins just like other pins
9 years ago
4b9d5cd352
Use lowercase names for serial instances
9 years ago
1e2deff4fd
Rename BTENABLED to BLUETOOTH
...
- For some reason it’s easy to forget what BT stands for, but it
doesn’t need an abbreviation.
9 years ago
68055a5959
Include RIGIDBOT_PANEL in Conditionals
9 years ago
f8ed3a835d
Added comment with the RigidBot Big bed size
9 years ago
7deae6b6be
Updated RigidBot example configuration
...
- The default serial baud rate of 115200
- The regular RigitBot bed size 254mm/248mm/254mm
- Single stock extruder
- Stock termistors for extruder and hotbed
- Stock Min X/Y/Z stops. Max stops not connected
- Stock 32 teth tooleys (stock axis steps)
- No auto bed leveling
- No screen
9 years ago
5418faa1f9
Add sanity checks for old names
9 years ago
f03e063750
Rename BEEPER to BEEPER_PIN
...
For consistency with other pins, allowing use of `PIN_EXISTS` macro.
9 years ago
270c766de2
SDCARDDETECT -> SD_DETECT, added docs
...
- `SD_DETECT_PIN` replaces `SDCARDDETECT`
- `SD_DETECT_INVERTED` replaces `SDCARDDETECTINVERTED`
- Revise the description of `SD_DETECT_INVERTED`
- Add a note about the override of `SD_DETECT_INVERTED` in
`Conditionals.h`
9 years ago
496fc28dc3
Tweaks to pins comments
9 years ago
8d3b74cc6e
Rename SDCARDDETECT to SDCARDDETECT_PIN
...
- Rename the pin so it can be tested with `PIN_EXISTS`
- Fix some incorrect tests for `SDCARDDETECT`
9 years ago
0f5ada8cbd
Group the fail case in one negation (PR#2572)
9 years ago
7ddf1cda1d
Improve condition for SERVO_LEVELING (PR#2570)
9 years ago
f32048b8f5
In for a penny, in for a pound
9 years ago
e944f960de
Add a sanity check for old name "BEEPER"
9 years ago
8ebf0b92be
Spacing adjustments in some pins files
9 years ago
94a796c8cc
Rename BEEPER to BEEPER_PIN
...
For consistency with other pins, allowing use of `PIN_EXISTS` macro.
9 years ago
b217474eab
Compiler Complaints about concatenated tokens (PR#2566)
9 years ago
2460f82d8b
Make proper distinction between BEEPER and HAS_BUZZER
9 years ago
58cfcd4239
Overridable Options - Part 5
...
Apply `ENABLED` / `DISABLED` macros to files needing only a small
number of changes.
9 years ago
5e834352a9
Overridable Options - Part 11 (PR#2563)
...
Apply `ENABLED` / `DISABLED` macros to EEPROM-related files.
9 years ago
bf6eb93c61
Overridable Options - Part 10 (PR#2562)
...
Apply `ENABLED` / `DISABLED` macros to planner files.
9 years ago
51e89a269c
Overridable Options - Part 9 (PR#2561)
...
Apply `ENABLED` / `DISABLED` macros to temperature-related files.
9 years ago
c35fb88094
Overridable Options - Part 8 (PR#2560)
...
Apply `ENABLED` / `DISABLED` macros to stepper-related files.
9 years ago
0d8989fc14
Overridable Options - Part 7 (PR#2559)
...
Apply `ENABLED` / `DISABLED` macros to LCD-related files.
9 years ago
b4abb0ae7f
Apply ENABLED / DISABLED to Marlin core files (PR#2558)
9 years ago
c0d7ea3e7e
Overridable Options - Part 4 (PR#2556)
...
Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files.
9 years ago
4b40964064
Overridable Options - Part 3 (PR#2555)
...
Apply `ENABLED` / `DISABLED` macros to language-related files.
9 years ago
32683b282b
Include configurator copies of configs
9 years ago
37d1879386
Apply overridables to Configuration files
9 years ago
9d151bb61b
servo_endstop_angles -> servo_endstop_angle
9 years ago
9334479aeb
Minor cleanup of Conditionals.h
9 years ago
1f63293624
servo_endstops -> servo_endstop_id
9 years ago
edaaead7e0
Fix comment about SERVO_ENDSTOP_ANGLES
9 years ago
ed4a6371ad
Add HAS_SERVO_ENDSTOPS to simplify conditonals
9 years ago
70be61d416
Reset filament_size with a loop
9 years ago
ae9274be05
Fix minor compiler warnings in for loops
9 years ago
c7c8cfed6f
Complete M200 output with M503
...
- The contents of EEPROM include filament diameters even with
Volumetric disabled. This change makes `M503` display the full
volumetric settings so that playing back the output of `M503 S0` will
fully restore them.
9 years ago
4a58e447a1
Add array size to servo_endstop_angles (PR#2553)
9 years ago
a0ae9e30df
don't pass integer by reference, inefficient. (PR#2547)
9 years ago
d03f037a92
Get rid of malloc() and free() (PR#2549)
...
Just the minimal changes to qr_solve.cpp and .h to get rid of malloc() and free().
Saves about 656 bytes of progmem (library-code)
and 22 bytes for static variables.
Should use exactly the same amount of stack as it did before on the heap.
9 years ago
3b2b2313ff
Combine if block related to SERVO_ENDSTOPS
9 years ago
0af2a80e06
Make SERVO_ENDSTOP_ANGLES 2-dimensional
9 years ago
525d0dc239
Configurator is out-of-date AGAIN (PR#2550)
9 years ago
dd22cbbfb8
makefile: add buzzer.cpp (PR#2479)
9 years ago
9f48798ffd
Replace ENABLED with DEFINED for SERVO_ENDSTOPS (PR#2542)
9 years ago
ae00fad75b
Rename as M100
9 years ago
a401d738df
There is an echo in here
9 years ago
ed7d45e8f5
Memory watcher
9 years ago
d17f7ebc8a
Multiply WATCH_TEMP_PERIOD by 1000UL (PR#2535)
...
instead of 1000. Else we get errors with times over 32 seconds.
9 years ago
bea6739774
Don't include Z_RAISE_AFTER_PROBING if not used (PR#2527)
9 years ago
81bba7ed88
More sanity checking for extruder requirements (PR#2531)
9 years ago
87a97f3724
Fix conditions for display strings
9 years ago
aaccea0260
Shift some display only strings from language.h to lenguage_en.h
...
and translate them to German.
9 years ago
e4c01f1c7e
Simplify init with ARRAY_BY_EXTRUDERS1 macro (PR#2507)
9 years ago
ab6f1fdf8b
Move & document ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED (PR#2528)
...
As suggested in #2521
- Move `ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED` because `SDSUPPORT` is
also required.
- Add a note that endstops must be enabled for the feature to have any
effect
9 years ago
1183c10a2e
makefile: drop -q -q (much quiet) from avrdude flags
...
Annoying when trying to figure out if uploading
actually does something.
9 years ago
0e064357f4
makefile: use /etc/avrdude/avrdude.conf on linux
...
No need to look for arduino specific avrdude configuration
as distributions ship their own avrdude.conf file that
is compatible with arduino.
9 years ago
bcb7d5a149
Improve sanitycheck for TEMP_SENSOR_1
9 years ago
5b24f59401
Add sanity checks for temp sensors
9 years ago
fd0e81b0c7
Distinguish between BUZZER and SPEAKER (PR#2513)
...
A speaker needs a AC or a pulsed DC to make a sound, a buzzer only needs a DC.
A buzzer has it's own resonator. It works in most cases to feed the buzzer with a pulsed DC, but the sound will not be as loud as with pure DC.
There seem to be boards where the BEEPER-pin is not able to handle a PWM. Obviously intended for a buzzer.
To make these board able to handle a speaker
* replace the PWM based tone()-function again with a on-delay-off-delay loop.
Hopefully the last time I touch the beeper code.
9 years ago
e2957df05c
Shorthand for do_blocking_move_to
9 years ago
819c5b9b50
Adjust comment on Z adjustment
9 years ago
5a7356b6fc
Patch for G29 final Z position
...
Include all the necessary pieces to get the final Z position after
probing the bed, and add commentary about other possible changes.
9 years ago
088e09e052
Add forgotten Marlin_main.cpp
9 years ago
8b876241bd
Some more servo code tweaks
...
Just set up the pin. Don't move to a random position.
Simplify servo::move()
* servo::move() does not need the pin parameter - The pin is set during servo_init() with attach().
* servo::move() does not need a return value.
SERVO_LEVELING is the wrong condition to deactivate the servos.
Remove some temporary (Servo *) variables.
SanityCheck for the servo indexes.
9 years ago
b116c096bd
Reduce set_homing_bump_feedrate, save 42 bytes (PR#2512)
...
Updates to `set_homing_bump_feedrate`:
- Move the string into Program Memory, reduce length by 31 bytes
- Use an auto to get the divisor, adjust it on error
- Set feedrate once, at the end
9 years ago
f7e7862588
Better Sanguinololu & Graphical Controller (PR#2504)
...
- Change suggested at
https://github.com/MarlinFirmware/Marlin/issues/2482#issuecomment-123553
266
9 years ago
a1154d4a20
Enable Y and sanity-check CoreXZ (PR#2509)
9 years ago
932f1c109e
Move servos to the top in pins_MEGACONTROLLER.h
9 years ago
90f8ddfc1e
Apply MINIPANEL to other configs
9 years ago
00dbf69b6d
add MINIPANEL defines
9 years ago
8ac5e56934
fixed some format problems and cleaned code
9 years ago
eef595aa64
add makerlab mega controller pin configs
9 years ago
4e14e152fa
Add Travis tests for CORXY and COREXZ
9 years ago
27d7d2ccab
Correct bracketing for COREXY-XZ
9 years ago
469843427d
Reduce code in gcode_M81 (PR#2497)
9 years ago
c66955aaf9
Mark unchanging arrays as const (PR#2494)
...
The compiler may be able to optimize if it knows an array won’t be
changing.
9 years ago
278aa15301
Add COUNT macro and apply
9 years ago
d85861d296
Move macros, add ENABLED/DISABLED, add includes
9 years ago
17960fd2b0
Neaten up pins_MEGATRONICS.h (PR#2493)
9 years ago
aac2b9aa9d
Reduce code in gcode_M84 (PR#2492)
...
`gcode_M84` only needs to call `finishAndDisableSteppers`, which calls
all the other functions.
9 years ago
4971fa73f9
Add a sanitycheck error for old servo settings (PR#2491)
...
- Documentation solution for #2476
9 years ago
96ace72ddc
Servos attach/detach based only on servo config
...
Assuming #2470 fixed up the main issue.
9 years ago
b80a6a8d31
Correct Kossel Pro Configuration_adv (PR#2473)
9 years ago
000a6fce46
Extract update_endstops from stepper ISR (PR#2474)
9 years ago
e83eac312e
Move plan_arc next to prepare_move
9 years ago
5c5936508d
G2/G3 Arcs for Delta
...
- Update prepare_move_delta to take a target argument
- Add Delta support to plan_arc
9 years ago
9f53e2f0c9
Implement COREXZ in stepper.cpp and planner.cpp
9 years ago
fa00e1d97f
Explode conditions common to corexy and cartesian
9 years ago
c7dd5527b4
Add a C_AXIS and Z_HEAD to support COREXZ
9 years ago
129f986ccf
Add COREXZ option to configurations
9 years ago
69b0490b77
Show minimal preheat options in menus (PR#2471)
9 years ago
eacfe132aa
Change the name of servos[] and servo_t
9 years ago
3b23ccd366
Patch servos code for move
...
- Have `Servo::attach` explicitly return -1 if it fails
- Check for -1 in `Servo::move` because `servoIndex` might be 0
- Make `attach` / `detach` calls conditional on `SERVO_LEVELING`
- Move `SERVO_LEVELING` define to `Conditionals.h`
9 years ago
54ddc1d417
Simplify DRY RUN (PR#2358)
...
Elsewhere DRYRUN turns off the heating elements
and ignores constraints on them.
Here, whenever motion is entered into the planner,
if DRY RUN is set, we instantly act as if the E_AXIS
is in the desired final position.
9 years ago
944090c19c
Optimize lsDive logic
9 years ago
417706e578
Include space for the terminating nul in lsDive
9 years ago
f3c1a6b19c
Reduce lsDive stack usage to the minimum
9 years ago
fba4e6241b
Specify print format for reporting invalid tmp_extruder (PR#2465)
9 years ago
d15d869267
Rename axis_is_at_home() to set_axis_is_at_home() (PR#2464)
...
to make clear - it's not a question but an order.
9 years ago
f209b755a5
Move the Z probe as far as needed to trigger the switch (PR#2461)
9 years ago
0f1df62389
Fixup comments in code_seen
9 years ago
2945eb6650
Call code_seen only once per parameter
9 years ago
b742af2e2a
Move Y_STOP_PIN for Printrboard with SD (PR#2420)
9 years ago
baa9199973
Define extern delta only for delta
9 years ago
77e80ef367
Require extruders for thermal code
9 years ago
PheiPheiPhei