03b0850e63
This breaks temperature readout for pronterface!
13 years ago
4ca2f336f0
Changed default MINIMUM_PLANNER_SPEED -> 0.05
...
Fixed small bug in arcs
M105 prints now actual_temp/target_temp
13 years ago
ae0bf8068b
Fixed arc offset.
13 years ago
0c1b863755
Ignore ":" in comments.
13 years ago
63aec3c56e
Replaced Kill by Stop. If the printer is stopped. Fix the error and use M999 to restart.
...
Moved the PID_dT in the Ki and Kd calculation from the configuration.h to temperature.cpp
13 years ago
f5eae52098
Added more manage_inactivity checks
13 years ago
87ff2f8867
Added CONTROLLERFAN. (Controlling a fan to cool down the steppper drivers)
13 years ago
387fe51a56
Do not disable steppers when there are moves in the queue.
13 years ago
7b1e295f34
Merge branch 'Marlin_v1' of github.com:ErikZalm/Marlin into Marlin_v1
13 years ago
c077316b2b
Added PID autotune. (experimental)
...
M303 Starts autotune. Wait till the Kp Ki and Kd constants are printed.
Put these values in Configuration.h
13 years ago
ce07c9186d
While Waiting for hotbed to warm up via M190, LCD Display and Click Encoder input freeze until target temperature is reached.
13 years ago
e056bf8081
Added E-Jerk
13 years ago
632528aa95
merging with SCUBA82
13 years ago
aac7aa3bf0
Queued fan control. Issue #90
13 years ago
fde51084f3
set SD file delete to M30; switch printime output to M31
13 years ago
21e2bae063
Changed (corrected?) SD_card comment handling.
13 years ago
cb0c84e075
Merge remote-tracking branch 'justblair/master' into Marlin_v1
13 years ago
ed951b1977
Fixed RAMPS 1.2 support (Found and fixed by rrhb)
13 years ago
046a8e0039
Added more defines to the language.h file so that nowe most of the text strings are now configured via this file. Still got some hunting down to do to complete this task.
13 years ago
5f3a422e68
added M31 - delete file from sd card
13 years ago
cb02914687
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
13 years ago
10bf2bb8e1
-
13 years ago
b4833d55c2
Fixed HOME_POS in combination with G28 X0 or G28 Y0
13 years ago
c6f2ec3c82
remove stop_heating_wait
13 years ago
b48d67ce10
Fixed homing
13 years ago
09469add55
Add board reset reporting (from Repetier-Firmware)
13 years ago
27f595a444
Changed version => RC2
13 years ago
84ea2d61e8
Moved gen7 boards to motherboard type 10, 11 and 12.
...
Split ramps1.3 in Sprinter like config and multiextruder config.
13 years ago
5aa9c41ab1
Changed comment mode for detection.
...
Added M221 extuder multiply factor.
13 years ago
ae3e7586c6
Added HOME_POS. This adds the posibility to make the center 0
...
Updated the Xsteps ... settings via the LCD menu
13 years ago
df1437bd86
Changed display format for some numbers.
13 years ago
d298dd121f
merged SBUBA82 and Justblair
13 years ago
2cc9a89830
Merge remote-tracking branch 'SCUBA82/Marlin_v1' into Marlin_v1
13 years ago
a0a1f81913
various changes
13 years ago
fe940a142d
Added a structure that will allow easy translations/modifications to the LCD menu.
...
Signed-off-by: Blair Thompson <mail@justblair.co.uk>
13 years ago
d309565b56
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
13 years ago
0e3631ff4b
smaller changes
13 years ago
7699f250e3
Fixed small merge bug
13 years ago
11518a987f
merged with triffid fork
13 years ago
13e185d330
removed unused HEATING_EARLY_FINISH_DEG_OFFSET
...
Simplified stepper inactive time
13 years ago
2a77c84c8f
Updated SERIAL define to MYSERIAL, because Arduino 1.0 defines SERIAL as 0.
13 years ago
f87c80889f
Fixed M109 timer overflow (reported by triffid)
13 years ago
154de69c02
Print configuration.h version during startup (thanks hairykiwi)
13 years ago
598eb1d4f1
Fixed compilation for gcc-4.6.2 with avr-lib-1.8.0 (thanks daid)
13 years ago
9173a5713b
Teensylu support.
13 years ago
5113513cb2
RC 1
13 years ago
d8a0c6450f
Split the configuration file in two parts.
...
One for common settings.
One for advanced settings.
13 years ago
b5fae1104b
fixed sUICIDE_PIN disable
13 years ago
e45e5c68bb
Added support for Gen3+ (Pins file only)
...
Added late z enable. (blddk request)
Only calculate look ahead if >2 moves in buffer.
Removed some FORCE_INLINE to save memory.
Signed-off-by: Erik van der Zalm <erik@vdzalm.eu>
13 years ago
3e575533c5
get M81 working
13 years ago
2ae2ead97b
help residency not overflow
13 years ago
8d0916af13
allow Marlin to actually compile with Makefile pulled from Sprinter and a few other modifications
13 years ago
6cc6029d7a
M109 EOL fix when TEMP_RESIDENCY_TIME is undefined; printer interface (pronterface) could not see target extruder heater temperature to continue print
13 years ago
157aa7f2fd
m115 eol fix
13 years ago
7aeb45303d
small mistake
13 years ago
cee5f9020a
added suicide pin for a power supply to the arduino that is only active if the arduino is holding high for an output.
13 years ago
57f9359a41
simplified the includes, makefile now works with arduino23
13 years ago
3c1a4aac2b
header file simplification
13 years ago
212515148e
added m240 photography support. default off
13 years ago
554cc1718d
Fiexed E_ENABLE_PIN errors
13 years ago
617968ab76
G92 fix
13 years ago
84d9cf7339
merging
13 years ago
e017228569
Merged multiple extruder support.
...
Soft PWM. (Sanguinololu can also have PID temperature control)
Interrupt save WRITE for addresses > 0x0FF
13 years ago
06411d5c9e
ultralcd can now also stop the wait loop for the hot-end m109 heating when stopping sd prints.
13 years ago
01001b89d2
repaired nozzle runout prevention to not collide with automatic stepper disabeling.
13 years ago
f6fe7143e4
Merge pull request #29 from k-eex/Marlin_v1
...
Fix M201 not saving settings in all places, so the changes did not get written into EEPROM
13 years ago
dde4b40fa9
disable steppers in runout prevention
13 years ago
2bc5e7ec9e
prevent too long extrudes, or too cold extrudes
13 years ago
aa4f9a6474
better values.
13 years ago
87fd249c43
made runout prevention independent of tempeorarily set esteps
13 years ago
1ec0c3b68a
extruder runout prevention.
13 years ago
5b4625f79c
added a partial release option to "m84" aka "stepper release". If you do tiny layers, you might want to keep the z-axis powered to not loose height positioning after homeing.
13 years ago
bae1e422f6
Fix M201 not saving settings in all places, so the changes did not get written into EEPROM
13 years ago
986f0ba76c
moved <stdio.h> to more dominant location.
13 years ago
460b788d78
repaired homing position setting.
13 years ago
4fd75dc813
Working version of multiple extruders (up to 3)
...
- The temperature control is pretty much complete
(not sure what to do w/ autotemp though)
Changed the pins assignment to clearly separate bed and extruder heaters
and temp sensors, changed a bit how termistor tables are handled.
- The steppers control is rudimentary
(only chanages what pins it uses depending on the active_extruder var,
but that's enough for switching extruder in the start.gcode in the
the profiles)
- Tested only w/ RAMPS 1.4
13 years ago
12e8edcac3
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
13 years ago
cf50ba140f
added M503 to display eeprom storage, and renamed eeprom routings. This version is compatible with the qtmarlin eeprom-tab.
13 years ago
b99c49ec3b
Add option to only check endstop when homing
13 years ago
7714b98da7
solved some compiler warnings that are now visible in arduino 1.0.
...
Found a couple of unused variables, that I commented.
Tried to solve the program memory warning message, and failed.
13 years ago
dfd240b260
overworked autotemp, removed one layer of nesting from the ultralcd.
13 years ago
4f909963e4
make QUICKHOME configureable
13 years ago
b0c3871750
more fixing of the sanguino math round problem
13 years ago
716e89b87c
first homing move diagonal towards home switches.
13 years ago
e4ab0e5982
more inlines
13 years ago
8cb29921a0
possible stepper release after sd printing
13 years ago
044886b4a0
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
13 years ago
6d95644c0d
Moved M88 into M84. (M84 E)
13 years ago
311627141b
Merge branch 'smallopt' into Marlin_v1
...
Conflicts:
Marlin/temperature.h
13 years ago
7216a12856
Disabled M88 for boards that don't have seperate enable pins.
13 years ago
98805c9228
Added M88 command. (Request from Action68)
13 years ago
f75f426dfa
Removed interrupt nesting in the stepper ISR.
...
Add serial checkRx in stepper ISR.
Copied HardwareSerial to MarlinSerial (Needed for checkRx).
13 years ago
2d9a715655
first naive attempt to have a offset in the homeing procedure. Does not enable to move into regions not allowed by endstops.
13 years ago
d2f034ba84
lcd message from gcode, m117
13 years ago
aad4b75b94
First parts 2nd extruder
13 years ago
a0dc66f7bf
Home retract distance configureable per axis.
13 years ago
4d6a5c29df
disable steppers as routine in stepper.cpp
13 years ago
74d0032e25
cooldown blocking selectable by #define.
13 years ago
57e163e989
typo
13 years ago
b58787a367
now velocities are also set in mm/sec in gcode.
13 years ago
grrf