14c03cb6f4
[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) ( #10069 )
...
Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.
7 years ago
468f34104b
Patch do_blocking_move_to so 'destination' can be used
7 years ago
28f1276286
[2.0.x] Add Z_AFTER_PROBING option ( #10058 )
...
Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.
7 years ago
751785fc97
Followup to recent patches
...
- `M666` is static, not inline
- Disambiguate some stepper macros
7 years ago
a0211f5d6c
Disambiguate else in stepper_indirection.h
7 years ago
f10c87b442
Update Endstops class for 1.1.x parity
7 years ago
239902f861
Fix E2END and add EEPROM to Smart RAMPS
...
Reference #9983
7 years ago
419d12ca1b
Add UNKNOWN_Z_NO_RAISE option
...
With this option enabled, Z won't ever be raised until after `G28` has been completed, and it won't raise if Z becomes unknown. This is good for machines whose beds fall when Z is powered off.
7 years ago
3b4c89e4b5
Move do_probe_raise closer to set_probe_deployed
...
…and limit the raise to Z_MAX_POS
7 years ago
2908e76151
Fix position_is_reachable_by_probe typo, add comment
...
Fix #10029
7 years ago
161ff9ff35
Fix UPDATE_ENDSTOP for CorePQ compatibility
...
Fixes #9939
7 years ago
49ca67202f
Patch configuration_store for extra serial port
...
Fix #9948
7 years ago
16a8edc5f0
Add more delay before pulse off in Linear Advance ISR
...
A capital idea from https://github.com/MarlinFirmware/Marlin/pull/9914#issuecomment-371614153
7 years ago
dfd5d2fe75
Have position_is_reachable_by_probe use the whole bed ( #10020 )
...
Previously `position_is_reachable_by_probe` was limited to the area specified for `G29` mesh leveling (even if leveling was disabled). This change will properly consider the entire bed area so that `G30` and other non-leveling probing may take place.
7 years ago
3c2bfa5e53
Update powersupply_on in power_on/off ( #10015 )
...
Fix #10004
7 years ago
8d32fd997f
Wrap NORM_E_DIR/REV_E_DIR macros in do{}while(0)
7 years ago
98d48fc731
Followup to HAL_timer_restrain
...
Followup to #9985
7 years ago
a1a88ebabc
HAL function to ensure min stepper interrupt interval ( #9985 )
7 years ago
9515e5aefb
Fix LA_active_extruder (static)
7 years ago
e5ec793f7e
Wrap stepper indirection macros
7 years ago
5b85464791
Fix for LA ( #9964 )
...
Missed in the original LA 1.5 PR: eISR has to use a local copy of
current_block->use_advance_lead because it might still run wenn the last
block has been set to NULL.
7 years ago
ffbf63e6af
Add HAS_TEMP_SENSOR conditional
7 years ago
2057177184
Make enums into implicit char
7 years ago
ca0def766e
LIN_ADVANCE single stepper optimization
7 years ago
8291ae34f2
Support duplication mode in LIN_ADVANCE
7 years ago
0dd1c4458d
Put more code between pulse start and stop ( #9959 )
7 years ago
36262a0479
Use static classes for job timers ( #9938 )
7 years ago
930720bbbb
Fix broken reverse planner ( #9943 )
...
From #9914 by @Sebastianv650
7 years ago
025118da3e
Init print_job_timer in setup() instead of "early" ( #9937 )
7 years ago
07ae23fe14
No pulse delay on last e_steps in advance isr
7 years ago
ed758de80d
tweak comment in stepper.cpp
7 years ago
d1dc863962
autotemp_factor is not value_celsius_diff
...
See https://github.com/MarlinFirmware/Marlin/issues/9852#issuecomment-369861822
7 years ago
f3914a432e
Clear retracted status when homing the Z axis
7 years ago
6d7f4f84e2
Add board MKS_BASE_HEROIC ( #9926 )
...
Followup to #9008
- Don't define micro-stepping pins for boards that lack them.
- Allow setting of 128 microsteps with `M350`.
7 years ago
649f375494
Fix: M112 calling kill from interrupt ( #9923 )
...
Fix #9906
7 years ago
23a576faf7
[2.0] Fix for FW retract ( #9878 )
7 years ago
91db7930dc
Drop SCARA_FEEDRATE_SCALING
...
The updated planner takes the length of the move, so this pre-calculation is no longer needed.
7 years ago
1746749361
Followup to #9868
7 years ago
a446433c87
Fix SENSORLESS_HOMING for Core Kinematics ( #9868 )
7 years ago
c22f8dd660
Get duration_t in printcounter.h for its clients ( #9843 )
7 years ago
966d9af98a
Mesh export in Bilinear + UBL M503
7 years ago
8d5a77001e
EEPROM parity with 1.1.x
7 years ago
cb4cb86d80
Useless line removed ( #9814 )
...
nextAdvanceISR is set in the next if structure in every possible
situation, so it's useless to set it once more before.
7 years ago
0557ab5780
Fix CONFIG_ECHO_START bug
...
In reference to #9633
7 years ago
813f9f3082
[bugfix_2.0.x] - LIN_ADVANCE V1.5 stepper.cpp ( #9797 )
...
Removal of obsolete (i) from port of LIN_ADVANCE from V1.1.x to V2..0.x.
7 years ago
3f89bbeab5
Drop a conditional only used once
7 years ago
689bc99402
Correction to acceleration
7 years ago
2bd252b501
[2.0.x] LIN_ADVANCE v1.5 ( #9712 )
7 years ago
2c9775313a
Fix Z position on HD44780
...
Fix #9732
7 years ago
5968a3e60e
Add ADVANCED_PAUSE_FEATURE include
7 years ago
73cd34b121
Finish AUTO_POWER_CONTROL implementation
...
Followup to #9503
7 years ago
b3deadd898
Don't raise FIX_MOUNTED_PROBE on stow
...
Reference #9336
7 years ago
3d1692d1fd
Fix X2 enable with X_DUAL_STEPPER_DRIVERS
...
From #9286
7 years ago
c241da32e8
stepper.h parity with 1.1.x
7 years ago
ca55f2927a
Pulldown pin mode support ( #9701 )
...
Implemented for LPC1768.
7 years ago
83d7e95de0
Add MSG_THERMAL_RUNAWAY_BED ( #9691 )
7 years ago
472229b974
Fix #9681
7 years ago
03d790451f
[2.0.x] HAL timer set/get count => set/get compare ( #9581 )
...
To reduce confusion over the current timer count vs. the compare (aka "top") value. Caution: this re-uses the function name, changing its meaning.
7 years ago
7280fa1e31
Patch Power class
7 years ago
e698998343
More reliable PROBING_HEATERS_OFF with BED_LIMIT_SWITCHING
7 years ago
1541224a81
Enable Z axis and delta sensorless homing ( #9516 )
7 years ago
d168ee9bed
Drop leveling include from steppers.cpp
7 years ago
b5e92f4f90
[2.0.x] Enable / disable PSU automatically ( #9503 )
7 years ago
ac6bf7226a
Update of comments in thermistor files. No functional changes. ( #8986 )
7 years ago
786746404b
[2.0.x] Apply feedrate to nozzle movement for kinematic machines ( #8778 )
7 years ago
e1fd9c08b3
[2.0.x] Add support for LPC1769 at 120 MHz ( #9423 )
7 years ago
9b9350e010
Fix jerky Z motion between probes
...
Suggested by #9375
7 years ago
ea9ad4e46d
[2.0.x] Fix compile error on delta when NO_WORKSPACE_OFFSETS ( #9388 )
7 years ago
c251601916
Simplified SET_BIT, moved to endstops.cpp
7 years ago
f8227abf1c
Merge pull request #9384 from tcm0116/2.0.x-retract
...
[2.0.x] Clear retracted status when homing the Z axis
7 years ago
5c69d45f5b
[2.0.x] TMC2130 support for LPC platform ( #9114 )
7 years ago
7035471982
Clear retracted status when homing the Z axis
7 years ago
2bea1bda56
Move more strings to PROGMEM
7 years ago
1dcfe193ac
Optimize some serial strings
7 years ago
9644fe1839
Lightly optimize arc length calculation
7 years ago
3217da6fa5
Followup patch for TMC stepper init
7 years ago
db031d5d76
Add missing SoftwareSerial begin for TMC2208
...
Based on #9299
7 years ago
f7f8569bbf
Fix skew settings report precision
...
Followup to changes from #8843
7 years ago
205c5fa078
Merge pull request #9277 from oysteinkrog/fix/DualX_Endstops
...
[2.0.x] Fix DUAL_X_CARRIAGE endstop tests
7 years ago
90d011cc48
Use ADD_PORT_ARG for all cases
7 years ago
51c7b5d46f
Fix set_home_offset bug from bad porting
7 years ago
61bf8478a2
Add hotEnough methods
7 years ago
7d6c009104
Add thermistor 15 tuned for JGAurora A5
7 years ago
382a5e3318
Clean up trailing whitespace
7 years ago
441517bbe1
Fix DUAL_X_CARRIAGE endstops
...
\#8170 fixed
7 years ago
887664aa61
Restore broken Dual X Carriage
7 years ago
2e2fd8fd79
Merge pull request #9261 from tcm0116/2.0.x-delta_softstops
...
[2.0.x] Allow DELTA to compile with soft endstops disabled
7 years ago
750cc02b3a
Use delay() in serial temp report
7 years ago
44239b1062
Allow DELTA to compile with soft endstops disabled
7 years ago
afec16e644
Merge pull request #9240 from tcm0116/2.0.x-eeprom
...
[2.0.x] Follow-on to #9161
7 years ago
429e6ba8a6
Fix lcd_preheat dummy variable types
7 years ago
d5bf9e74c4
Merge pull request #8996 from p3p/pr_bf2_more_adc_filter
...
[2.0.x] PID control fix and more LPC1768 ADC filtering
7 years ago
42933c804a
Cleanups for STM32F7
7 years ago
a0246c5c96
Add support for STM32F7 MCU
7 years ago
a408209d24
More reliable temperature serial report?
7 years ago
4f5e087ff4
Planner anti-stutter by Sebastian Popp
7 years ago
cfd989d7c5
Fix EEPROM SettingsData for 32-bit architectures
7 years ago
da600e5fbe
Merge pull request #9132 from Bob-the-Kuhn/add-VIKI2-to-Travis
...
[2.0.x] add VIKI2 test to Travis & fix LCD contrast (again)
7 years ago
84de428d30
[2.0.x] Fix compile errors ( #9141 )
...
* Update persistent_store_impl.cpp
* Remove define BYTE from serial functions since Arduino docs typically show 0 for the normal case.
7 years ago
e633ce06c7
LCD contrast type mismatch is back
...
WORKS!
7 years ago
f7efac57b7
Multi-host support
7 years ago
7e000e6af4
More EEPROM field debugging ( #9123 )
7 years ago
5295b4713d
[2.0.x] add semitec 104NT-4 ( #9119 )
...
Table is very very similar to old 104-GT2 so I added only the name and recycled old ID
7 years ago
99516572b1
Fix TMC current read from EEPROM
7 years ago
14dcad6bbc
LPC1768: Increase ADC median filter from 3 values to 23
...
Clarify the HAL_adc_get_result method to make sure correct values enter the filters
HAL: Fix the PID control loop for non-AVR platforms
7 years ago
60d07f20e7
Make mbl.has_mesh() a method
7 years ago
2b5a9be49c
Fix M503 skew output
...
Followup to 19e75ccf86
7 years ago
702c8acdd5
Settings FIELD_TEST fix
7 years ago
e89f1453ab
UBL G29 works without settings.load()
7 years ago
950be70a33
Add FIELD_TEST to validate storage
7 years ago
760c912ab9
Add data size validation
7 years ago
b91ca168fb
Add a struct defining EEPROM storage
7 years ago
51e0f2bee3
Add MarlinSettings::validate()
7 years ago
878f54c27b
Write filler with NO_VOLUMETRICS
7 years ago
3ea6745b36
Pretty up TMC current write
7 years ago
1c41de16d4
Trailing whitespace clean
7 years ago
1746a7352e
Merge pull request #9042 from thinkyhead/bf2_M701_M702
...
[2.0.x] Improved Pause/Load/Unload, M701-M702
7 years ago
3a4e107b6b
use SERIAL_EOL(); instead of new line string
7 years ago
19e75ccf86
Add enough precision so planner.xy_skew_factor doesn't print as 0.00
7 years ago
7541316bb4
Add M701/M702 Filament Load/Unload, M603
7 years ago
a80f2eea23
Group leveling reports for folding
7 years ago
0e93506985
Fix for issue #9005 , #8942 - Bed PID autotuning ( #9036 )
7 years ago
4af3d436b2
M303 pid autotune cleanup, commentary
7 years ago
e43f3ac989
EEPROM init fix
7 years ago
fc67c64b8f
Merge pull request #8989 from tcm0116/2.0.x_ubl
...
[2.0.x] Fix UBL compilation warnings
7 years ago
8afc4f8d9d
Fix UBL compilation warnings
7 years ago
5e01ee8adf
Temperature updates for parity with 1.1.x
7 years ago
d80c4f1a6e
Fix typo in delta call to buffer_line
...
Fix #8901
7 years ago
5effe1590c
Fix NO_VOLUMETRICS bug
7 years ago
4b49ea1e92
General cleanup of config-store, reset_bed_level
7 years ago
705ea98fd3
Comment `return false` in motion functions
7 years ago
50366b00d5
Tweak cleaning buffer / SD finished command
7 years ago
869c89d83f
Merge pull request #8865 from thinkyhead/bf2_more_scara_scaling
...
[2.0.x] SCARA Feedrate Scaling for G2/G3 - using HYPOT
7 years ago
2917d1217d
Revert "Followup to #8698"
...
This reverts commit 4e891e9fb7
7 years ago
caa5093498
General DELTA_IK macro
7 years ago
c694608450
Apply SCARA_FEEDRATE_SCALING to G2/G3
7 years ago
97d509d4d2
Revert "Improved Core-compatible jerk code"
...
Reverting commit 3cd7659
7 years ago
5bc2acc072
Restore position_float to fix LIN_ADVANCE
7 years ago
913d9e9a59
Matching sign across filwidth vars
7 years ago
fdc5e72720
A single setting to validate filament width
7 years ago
933f76fda3
Option to disable all volumetric extrusion
7 years ago
fc9ee1a4de
Fix up serial sanity check
7 years ago
de5ca96654
More parity with 1.1.x, plus whitespace
7 years ago
8df5955da4
Revert "Reset timer count before first block step"
...
This reverts commit 5cf6a062e3
7 years ago
0cd1e91056
[2.0.x] TMC driver update ( #8769 )
7 years ago
09d13f186f
Correct unskew, after all
7 years ago
0d531d9655
Missing HAS_HEAT_BED conditional
...
Fixes issue found in #8779
7 years ago
368c124de8
Fix Planner::unskew parity with skew
7 years ago
cf2193c07f
Comment, fix filament width sensor
7 years ago
24f9bec6f4
UBL + DUAL_X_CARRIAGE compatibility
7 years ago
3255712343
Skew Correction for UBL
...
Also remove unused grid slicing function when using UBL segmented.
7 years ago
3db5303bfe
_buffer_line => buffer_segment
7 years ago
a71d2f3f40
UBL_DELTA => UBL_SEGMENTED
7 years ago
73e32925e4
References are better for array args
7 years ago
a5150c83a2
[2.0.x] Multiple updates to STM32F1 HAL ( #8733 )
...
* STM32F1 HAL
Adding files for STM32F1 HAL based on libmaple/stm32duino core.
Current persistent_store uses cardreader changes to be sent in separate
commit, but could be changed to use i2c eeprom.
There is another persistent_store implementation that uses the MCU flash memory
to emulate eeprom
Adding readme with some information about the stm32 HAL.
* Switch to Timer4 to avoid a hard reset on STM32F103C6 boards
On bluepill STM32F103C6 boards, using Timer5 results in a error() vector call. Switch to 4 since these are both general purpose, 16 bit timers.
* Add support for EEPROM emulation using Flash
Some low end machines doe not have EEPROM support. Simulate it using the last two pages of flash. Flash does not allow rewrite between erases, so skip writing the working version if that's enabled.
* Basic Pins for a malyan M200
This is a work in progress to go hand in hand with the STM32 work.
* Add support for ADC with DMA. This work has exposed a problem with the pin enumerations in STM boards vs what marlin expects (i.e, try defining PA0 as a temp pin). The hack can be removed with we go to fastio completely. To see this work, set something in adc_pins to a value like PA0 and connect your pullup resistor'd thermistor.
* Missing file - change HAL_adc_init to actually do something
We have an actual ADC init function now.
* Remove pinmode hack
Remove the pin mode hack that I was using to init PA0.
Updated Readme.md
* Several changes to timers and GPIO
Faster GPIO, and faster timer functions by accesing registers and
libmaple.
Still more changes pending for the Timer's code to skip using the
HardwareTimer class altogether.
Switch all enums to be within #defines
This change allows a user to have, for instance, TEMP_4 and TEMP_BED definied but nothing else. The enums which are not defined move "out", allowing the first ones to take the slots in the enum, and since the array is sized on ADC_PIN_COUNT, we always have the right size data and in order.
* Update Malyan M200 pins
Update Malyan M200 pins with correct fan values.
* Test all pins on actual hardware, update definitions
Some of the pin definitions were from knowlege base/pdfs. Now they've been tested against actual hardware. This should be very close to final.
* Update HAL_timers_Stm32f1.cpp
* Add sample configurations for Malyan M200
Add sample configuration for Malyan M200 without bed leveling, and move fan to auto cool E0 since this printer by default has only one fan.
Choose the timer based on MCU defintion. Timer5 is not valid on C8/CB class boards, so use Timer4 for the step timer.
readme.md update
* Updates to timers, and some stm32 boards definitiions
* Correct pin toggle macro.
* Remove duplicated Malyan M200 entry from pins.h
* Update configuration_store.cpp
* Formatting, indentation
* Formatting in HAL_Stm32f1.cpp
7 years ago
204199e1ce
Only compare XYZ to check motion
7 years ago
6686d937fb
Always report position on config load/reset
7 years ago
03ba79f144
Sync and report changed position
7 years ago
5cf6a062e3
Reset timer count before first block step
7 years ago
82ef6b5242
Add an option to specify "pulse" timer
7 years ago
4fa65a5c25
TCNT0 => HAL_timer_get_current_count
...
Fix #8710
7 years ago
b3daf6b5db
[2.0.x] better reverse pass ( #8722 )
...
* repair reverse_pass()
And make it readeble.
This was broken a long time ago.
Not competely unfunctional but far from optimal.
* Minor speedup when calling calculate_trapezoid_for_block
2 float / to 1 foat / and 2 float *
* Various style changes
7 years ago
65d0f32f82
divide only when required
7 years ago
728acf521c
Followup to #8706
7 years ago
85c6ffbe0d
Discard all "continued" blocks on interrupted move
7 years ago
4e891e9fb7
Followup to #8698
7 years ago
de3d3b9cb1
Put FORCE_INLINE before static
7 years ago
ae663a4198
PROBE_DOUBLE_TOUCH => MULTIPLE_PROBING
7 years ago
3cd7659924
Improved Core-compatible jerk code
7 years ago
81c0a918af
feed_factor => inverse_secs
7 years ago
9898b96992
No lcd_map_control flag in quick_stop
7 years ago
840289e7cc
Use block cleaning instead of split flag
7 years ago
2fde60da12
Changes for parity with 1.1.x
7 years ago
6040d4080e
Cleanup stepper ISR. Allow cleaning for endstops.
7 years ago
a4e1d83599
Fix M503 S parameter
7 years ago
a993c5227d
Don't split first_move while homing or probing
...
While homing or probing it might be bad if the stop/trobe triggers during the first part and the second is still in the buffer.
7 years ago
5fbb2f121e
Remove skew warning that could crash the planner
7 years ago
c1184552ac
Change K1 to required option PID_K1
7 years ago
d8b444c144
Cleanup constextpr in planner.cpp
7 years ago
a2372cfab5
Fix SKEW_CORRECTION without leveling
7 years ago
b27bc67271
Set initial endstops state
7 years ago
53694ebaa1
Folllwup to planner splitting
7 years ago
4b612f590c
Split first move to planner for better chaining
7 years ago
dd8febca1a
Revert "Merge pull request #8611 from thinkyhead/bf2_planner_split_first"
...
This reverts commit 824980e70eaa7efb96bf
7 years ago
3a97de52ef
Split first move to planner for better chaining
...
Address #8573 , #8595
7 years ago
63a91cd37a
Fix a homing comment
7 years ago
8056120195
Rename inverse_mm_s => inverse_secs
7 years ago
23557f8e77
Remove obsolete de_float
7 years ago
05f8e98c4a
Fix for issue #8629 - mismatch between number of stored and loaded dummy items on non-delta machines. ( #8631 )
7 years ago
000b3b3117
Comment/cleanup of motion code
7 years ago
45c2388a58
Apply const to thermal_runaway_protection args
7 years ago
0154e3480c
New feature: BED_SKEW_CORRECTION
7 years ago
91fb6231b2
Fix EEPROM V45 header, layout
7 years ago
dd3ce40826
Drop Planner::position_float, use int types
7 years ago
ec6ca37ed3
Fix (un)apply_leveling fade bug
7 years ago
a52fec6ac4
Planner class parity with 1.1.x
7 years ago
23e45fa3c4
Apply const to some planner vars
7 years ago
ef2531558c
Add an option to segment leveled moves
7 years ago
285b868e9b
Tweak planner code style
7 years ago
1f2acc33bc
Tweaks for check_axes_activity
7 years ago
a8aa43ce2d
Merge pull request #8587 from AnHardt/2_Fix_WDTO_during_long_DELTA_moves
...
[2.0.x] Fix WDTO during long delta moves
7 years ago
16baa48699
Fix #8579
...
Fan speed code fell into a curly brace
7 years ago
02aa93a6ad
Fix Watchdog time out during long lasting DELTA moves
...
During long lasting moves of a delta machine neither the temperatures are maintained nor buttons checked nor ... .
The fix is to call 'manage_heater()' and 'idle()' every now and then in the loop where the move is segmented.
The code is abot the same as in G2_G3 wher we had the same problem with too large circles lasting too long.
Fixing #7510
7 years ago
fadf9eb2d7
Simplify midpos calculation
7 years ago
a67cf78c6b
Clean up whitespace, spacing
7 years ago
25674da90c
Tweaks to do_blocking_move
7 years ago
27c5692b13
Syntax tweaks
7 years ago
65f365333f
[2.0.x] G33 probe error handling
7 years ago
d29cb646e3
Fix erroneous reference to temperature in time calculations
...
Travis is having problems at: https://github.com/MarlinFirmware/Marlin/pull/8560
So... doing a direct commit to get things correct. Bugfix_v1.1.x does not have this bug. Nothing needs to be done to that branch.
7 years ago
a9ecb975b2
Apply LINEAR_UNIT to M503 output for M200
7 years ago
80ada58818
One fewer function call in probe_pt
7 years ago
01e207213f
Fix MK2_MULTIPLEXER stepper indirection
7 years ago
a03f93bab4
Fix fan kickstart
7 years ago
9e3c41f9e8
Tweak fan kickstart / speed code
7 years ago
118ac61e59
[2.0.x] Tool change bad behaviour fix
...
Previous fix did not work as expected when axeis not homed. It raise Z but never return to original position
7 years ago
617993d0ea
Patch for !!TEST (was _BV once?)
7 years ago
a61127a421
[2.0.x] tool change bad behaviours
...
This will solve 2 issues on tool change.
1) when no home is done ("no_move" is set) tool change should never move X & Y because... I don't know where I am...only Z should be adjusted to avoid bed collision if other nozzle is lower than current.
Since no move no bed level matrix should be applied
2) When SWITCHING_NOZZLE is enabled and system is homed there are two movements to go to destination, but first can move Z to older position and then crash on the bed
7 years ago
e2724c68ab
Update pins_RURAMPS4D.h
...
Add and bugfix pins
7 years ago
33912fa7e8
Update Temperature::setPwmFrequency prototype to match source
...
Introduced with #8446
7 years ago
25af9decfe
Remove enum.h include of MarlinConfig.h
7 years ago
1d4571b88d
Dependency adjustments
7 years ago
c0000a0cdc
Move servo code to modules/servo.*
7 years ago
c14000775b
PWM fixes, slow down fan update
...
include LPC1768 syntax for M42
couple more pin_t changes
consistency
change M42 to R, P format
Revert "change M42 to R, P format"
This reverts commit 01f12f579ec9ccc1bb9126e68d2c86449e9b7edf.
7 years ago
60adc6ff02
Display filwidth ratio in terms of E mm
7 years ago
485abb023b
Merge pull request #8456 from thinkyhead/bf2_wednesday_tweaks
...
[2.0] No retroactive adjustment with M851 Z
7 years ago
3bba7d60f3
No retroactive changes with M851 Z
...
If using babystep to adjust the Z probe offset, the axis will move and the mesh will be updated at the same time, causing a doubling of the Z offset over the rest of the print.
To correct for this, the current Z position would need to be modified in the opposite direction, canceling out the additional Z offset added to the mesh. This would be confusing to users, and moreover it would not be accurate without also taking the current Z fade level and current Z height into account.
It might make sense to change the mesh in the case where no babystepping is taking place, but this could be considered an undesirable side-effect of changing the `zprobe_zoffset`.
One way to remedy this would be to return to storing the mesh with `zprobe_zoffset` included, then subtracting `zprobe_zoffset` from the returned Z value. Thus, a babystep moving the Z axis up 1mm would subtract 1 from `zprobe_zoffset` while adding 1 to all mesh Z values.
Without including the `zprobe_zoffset` in the `z_values` there is no safe way to alter the mesh in conjunction with babystepping, although it's fine without it.
7 years ago
32512332df
Apply some formatting
7 years ago
7eea000f4b
E0 auto fan fixes
7 years ago
b2dda096fe
Fix FILAMENT_LCD_DISPLAY for disabled state
7 years ago
1e8afb66b7
Fix a planner comment
7 years ago
50f09cc029
Miscellaneous cleanup
7 years ago
63257dc083
Fix M503 output for M145
...
Fixes #7978
7 years ago
0918dae66e
Add OV() macro for use in thermistor tables
7 years ago
6131533157
Change dithering behavior to intended.
7 years ago
91baca6abb
Patches for compiler warnings/errors
7 years ago
04abd8d459
Improve and clarify M428 code
7 years ago
f5d210c35c
Fix report_current_position
7 years ago
06ee6584fd
Remove offsets from soft endstops, tool change
7 years ago
d4a1154c25
Use do_blocking_move_to where possible
7 years ago
36426af564
Merge pull request #8356 from tcm0116/2.0.x-M600
...
[2.0.x] Normalize load/unload length in M600
7 years ago
1ed86adf9c
Cleanup around updatePID
7 years ago
75a58ee4b8
Fix position_is_reachable bug in waiting
7 years ago
e334efb2a7
PROBE_MANUALLY etc.
7 years ago
cba9c1cf9e
Add pre-calculated planner.e_factor
7 years ago
600c85226e
Normalize load/unload length in M600
7 years ago
c66696c507
Merge pull request #8344 from tcm0116/2.0.x-delta_height
...
[2.0.x] Add delta_height variable in lieu of using home_offset
7 years ago
0cfb936dd1
Clarify some motion code
7 years ago
f34c3597dc
Add delta_height variable in lieu of using home_offset
7 years ago
b0b4a20930
Tweaks to core motion code
7 years ago
1c6e83c137
if !HAS_MESH we still need to do some motion! ( #8328 )
...
* if !HAS_MESH we still need to do some motion!
Thank You MagoKimbra !
* Ooops.... need #else and not #elif
7 years ago
Scott Lahteine