703f3b38c4
Merge remote-tracking branch 'upstream/Development' into Development
10 years ago
37cde8a191
Report changes from previous PR from old code base including :
...
I've updated the minimum values from the LCD.
It has been a while that i want to at least fix this.
I have an inductive probe and often i need to set my zOffset to something lower than 0.5.
With the current implementation, the default LCD value is set to 0.5 for some reason.
On my case i need to be able to set it down to 0.0 as my inductive probe can be lower than 0.5.
Before with the LCD we couldn't change this value below 0.5. We had to flash the firmware every time which was painful.
Now we are able to change this value down to 0.0 if needed.
I've also changed the minimum value for Z min acceleration.
In the default configuration it's set to 25 but on the LCD the minimum was 100 which is not coherent.
I've changes the minimum to 10. On this axis, depending on the mechanics/motor drivers we might require very low acceleration, so i guess 10 is somehow realistic.
10 years ago
b26a3ea02c
Merge pull request #1662 from josla972/refactor_scara
...
Refactor SCARA calibration. Save some lines of code and possibly ROM.
10 years ago
e6f6c6e3a1
fix bad insertion config again
10 years ago
6bdee87be3
Cleanup temperature code
...
- Get rid of unused temp states in the ISR, resulting in more frequent
temperature reading with fewer sensors
- Shrink code slightly in min/max testing
10 years ago
34a41648ab
Merge branch 'Development' into planner_oh_planner
...
Latest upstream commits
10 years ago
4fbb80567e
Get upstream commits
10 years ago
7717e1ce33
Fix bad insert in configuration
10 years ago
146501215f
Fix mangled probe_pt calls
...
- Address issue #1669
- Remove the TOPO_ORIGIN configuration setting
10 years ago
15345cc249
Corrected Z_PROBE_ALLEN_KEY behaviour.
10 years ago
0f034dd97e
Clean up Z_RAISE_AFTER_PROBING to work the same in all code paths except Z_PROBE_SLED.
10 years ago
6c96f32069
Blind fix for #1507
10 years ago
379348487e
Removed malplaced comment.
10 years ago
8bd6e37b21
Merge pull request #1661 from thinkyhead/G92_no_offset
...
Don't add home offsets in G29
10 years ago
582cd780cd
Fix compile error with `*_DUAL_STEPPER_DRIVERS`
...
- Patch up macros in stepper.cpp
10 years ago
9b3462f73f
Refactor SCARA calibration. Save some lines of code and possibly ROM.
10 years ago
691e753cc3
Don't add home offsets in G29
...
- Address #1262 by leaving values as set
- Rename `add_homing` to `home_offset`
10 years ago
88e81a4804
Latest upstream commits, plus fixes
...
- Also add Manual Bed Leveling to the rest of the configs
10 years ago
15eb5d35a2
Merge branch 'Development' into config_testing
...
Latest upstream commits
10 years ago
19df90622b
Include Conditionals.h file in update
10 years ago
9b639b4135
Merge pull request #1619 from epatel/manual-bed-leveling+mesh-bed-level
...
Manual bed leveling + mesh bed leveling
10 years ago
2c9bd15625
Move LCD items to `Conditionals.h`
...
- `Conditionals.h` is included twice, setting LCD values the first time
10 years ago
63abeaff38
Merge branch 'Development' into config_testing
...
Latest upstream commits
10 years ago
3703694e30
Fix temperature min/max test
...
- Base tests on all thermistors/thermocouples, not just heater 0
10 years ago
3d0a060a7a
Added G29 command
10 years ago
c516747847
Merge branch 'Development' into manual-bed-leveling+mesh-bed-level
10 years ago
af14c684b5
Minor optimizations to planner code
...
- Prefetch values used more than once
10 years ago
13fbf42d95
Cleanup of planner code
...
- Use named axis indexes, `X_AXIS` etc.
- Replace `block.steps_A` with block.steps[A]`
- Replace `A_segment_time` with `segment_time[A]`
- Add `A_AXIS`, `B_AXIS` for `COREXY` axes
- Conditional compile based on `EXTRUDERS`
- Add BLOCK_MOD macro for planner block indexes
- Apply coding standards to `planner.h` and `planner.cpp`
- Small optimizations of planner code
- Update `stepper.cpp` for new `block` struct
- Replace `memcpy` with loops, let the compiler unroll them
- Make `movesplanned` into an inline function
10 years ago
64e3d33893
Fix shrinked menucode
...
by updating 'encoderPosition' in END_MENU() line 1.
10 years ago
a7e89d4cfa
Merge branch 'Development' into manual-bed-leveling+mesh-bed-level
10 years ago
8c5bb38748
Removed now unneded FONT_STATUSMENU
10 years ago
2176a22d42
Fix count_direction initializer
...
- Addressing #1625
10 years ago
e72cb3e45d
Merge https://github.com/MarlinFirmware/Marlin into tm2-utf-minus-kanji
...
Conflicts:
Marlin/dogm_lcd_implementation.h
Marlin/ultralcd_implementation_hitachi_HD44780.h
Fix merge conflicts 2
10 years ago
cb6942d4a7
Merge branch 'Development' into config_testing
...
Get upstream commits
10 years ago
6bfccaf99e
Merge https://github.com/MarlinFirmware/Marlin into tm2-utf-minus-kanji
...
Conflicts:
Marlin/dogm_lcd_implementation.h
Marlin/ultralcd_implementation_hitachi_HD44780.h
Fixed conflicts 1
10 years ago
5644ad6809
Fix hiliting of edit items
10 years ago
63d5d28085
Merge branch 'Development' into config_testing
...
Latest upstream changes
10 years ago
526a755a66
Merge pull request #1652 from AnHardt/PIDdebug
...
PID debug
10 years ago
a1c240b0a4
Delta supports some auto bed leveling options
10 years ago
5112cf8422
Added comment for the EEPROM storage
10 years ago
4619d80524
Merge branch 'Development' into manual-bed-leveling+mesh-bed-level
10 years ago
199151a4ed
Merge pull request #1650 from AnHardt/beautify
...
Beautivy statusscreen
10 years ago
2424713a8f
Merge pull request #1640 from AnHardt/warning6
...
codepos not used in gcode_M28()
10 years ago
b6d381f863
Divide up Conditionals to get LCD items early
10 years ago
e85061d20d
Added changes to the 'new' Configuration.h s
10 years ago
33c7c6e11d
Conditionals.h requires Arduino.h
10 years ago
8ade04b78e
Felix and Hephestos configs
...
- Not sure why these are showing as all new
10 years ago
670006b919
Remove invariant code from Configurations
...
- Add `Conditionals.h` with calculated configuration values
- Add `SanityCheck.h` with checks for configuration errors
- Remove equivalent code from all configurations
- Move error checks from some sources to `SanityCheck.h` also
- Fix initialization of count_direction in stepper.cpp
10 years ago
a61f679568
Merge branch 'Development' into manual-bed-leveling+mesh-bed-level
10 years ago
c87faa69ed
Shortened mesh_plan_buffer_line()
10 years ago
47c1ea72af
Merge https://github.com/kieranc/Marlin into PIDdebug
...
Conflicts:
Marlin/temperature.cpp
Cleaned merge conflict.
Codeposition had changed.
Variable pid_input had vanished.
Signed-off-by: AnHardt <github@kitelab.de>
10 years ago
f1d3d1524d
Merge branch 'optimize_menu_code' of https://github.com/thinkyhead/Marlin into beautify
...
Conflicts:
Marlin/dogm_lcd_implementation.h
solved merge conflict.
10 years ago
fa889cd6e1
Beautivy statusscreen
...
by shifting things some pixels around
10 years ago
7279e4f82f
Small code tweaks re lcd.print
10 years ago
90ba61b9b8
Include indicator for new drawmenu_generic
...
In the new method we pass the character that should be used for
selected state, not the character to print always.
10 years ago
15d29efad5
Pass sel to lcd_implementation_mark_as_selected
...
- Pass selected state directly to lcd_implementation_mark_as_selected
- Rename sel function parameter
- Include a minor fix for SdBaseFile.h
10 years ago
a547dc2148
Merge branch 'Development' into optimize_menu_code
...
Get upstream changes
10 years ago
9c1f6e7ac7
Merge remote-tracking branch 'upstream/Development' into Development
10 years ago
e650d4044e
Fix "Stop Print" function in the LCD menu
...
When one hit "Stop Print" option in LCD menu, the command buffer was not
cleared. The printer keep moving until the buffer has been emptied.
Actually I could not clear the command buffer as well.. I don't know
why, it doesnt work as expected.
I need to implement a routine inside Stepper ISR to handle such
situation.
10 years ago
e917477fec
Merge https://github.com/MarlinFirmware/Marlin into tm-utf-minus-kanji
...
Conflicts:
Marlin/dogm_lcd_implementation.h
Marlin/fonts/make_fonts.bat
Claerd conflicts with my own #1621 . (His was easy. :-) )
corrected typo in fonts/README.fonts
Applied changes to the new delta-configurations
and deletet there some extra whitespace at the line-endings.
10 years ago
ae01a6b5f2
Make use of codepos.
...
Saves one addition.
Needs one pointer on the stack.
Don't know if this is a go trade.
10 years ago
a534ac197a
Merge pull request #1621 from AnHardt/remove--6x9-font
...
Remove 6x9 font
10 years ago
80e0ee10ca
Merge pull request #1631 from AnHardt/iss1593
...
Decrease KILL_DELAY
10 years ago
4ce79920e5
Merge pull request #1635 from AnHardt/warnings1
...
Negative times are unlikly
10 years ago
76127b8a55
Merge pull request #1630 from Wurstnase/fix_g29
...
optional parameters must be named when ignoring order
10 years ago
be3f2dc1d9
Merge pull request #1636 from AnHardt/warning2
...
lcd_control_retract_menu() is conditional.
10 years ago
8d396584bf
Merge pull request #1637 from AnHardt/warning3
...
lcd_autostart_sd() has two conditions.
10 years ago
8664c6d465
Merge pull request #1638 from AnHardt/warning4
...
delta[3] not used when DELTA not defined.
10 years ago
10711ccc6a
Merge pull request #1639 from AnHardt/warning5
...
G4 could wait for an undefined time
10 years ago
28c91deb5c
EEPROM saving of z_values.
...
Tried to make it a little intelligent.
10 years ago
240b5cfe04
Merge branch 'Development' into manual-bed-leveling+mesh-bed-level
10 years ago
4521f6655b
Restore "S" parameter of M204 for retrocompatibility.
10 years ago
5ddb8d94e2
Update Documentation related to M204
10 years ago
f8c4d43886
delta[3] is used with SCARA
...
Shoot in the dark.
10 years ago
72a9fed4fb
codepos not used in gcode_M28()
...
Got:
Marlin_main.cpp:2567: warning: unused variable 'codepos'
Needs revision.
Don't now how this should look like.
10 years ago
b94dd33641
G4 could wait for an undefined time
...
Got:
Marlin_main.cpp:1689: warning: 'codenum' may be used uninitialized in this function
And indeed codenum is undefined when no parameter is given.
10 years ago
e90985a4e8
delta[3] not used when DELTA not defined.
...
got:
Marlin_main.cpp:387: warning: 'delta' defined but not used
Compiles cleaner when definition is removed.
10 years ago
5099b86ad4
lcd_autostart_sd() has two conditions.
...
got:
ultralcd.cpp:408: warning: 'void lcd_autostart_sd()' defined but not used
10 years ago
5d81c779cc
lcd_control_retract_menu() is conditional.
...
Got:
ultralcd.cpp:64: warning: 'void lcd_control_retract_menu()' declared 'static' but never defined
10 years ago
450b89e63c
Negative times are unlikly
...
While bunting an other bug I stumbled across:
ultralcd.cpp:1250: warning: comparison between signed and unsigned
integer expressions
Changed to the type of lcd_next_update_millis.
10 years ago
d1658eebfc
Decrease KILL_DELAY
...
Users hat to press kill-button for unexpexted lon times.
See #1593
10 years ago
00adb2a6c1
optional parameters must be named when ignoring order
10 years ago
0d43898a22
Remove of mesh_plan_buffer_line parameter reference (e)
10 years ago
8067a985ce
Merge branch 'Development' into manual-bed-leveling+mesh-bed-level
...
Fixed conflicts:
Marlin/planner.h
10 years ago
05333f61b7
fix macro
10 years ago
1883e1bb60
Applied thinkyheads corrections from 2015-03-17
10 years ago
be79235ef2
Add new (cleaner) Marlin font
...
with sources in /fonts
10 years ago
89fe77468d
Merge pull request #1586 from maverikou/delta_auto_bed_level
...
Delta auto bed level (Updated PR)
10 years ago
2b1ddc0413
Merge remote-tracking branch 'upstream/Development' into Development
10 years ago
cb676cdf39
Fix CoreXY homing bug introduced by PR #1606
...
The Check Endstop logic must be:
if (current_block->steps_x != current_block->steps_y || (TEST(out_bits,
X_AXIS) == TEST(out_bits, Y_AXIS)))
if (TEST(out_bits, X_HEAD))
not
if (TEST(out_bits, X_HEAD) && (current_block->steps_x !=
current_block->steps_y || (TEST(out_bits, X_AXIS) == TEST(out_bits,
Y_AXIS))))
Same applies for Y axis.
10 years ago
8a29dd4839
Cleaned typo in dogm_lcd_implementation.h
10 years ago
7e69f72db6
Moved font directory. Updated README.fonts
10 years ago
00b162a993
Merge remote-tracking branch 'origin/utf-kanji' into tm-utf-minus-kanji
...
Conflicts:
Marlin/language.h
Conflict cleaned
10 years ago
e38dd5f030
Merge remote-tracking branch 'origin/utf' into utf-kanji
10 years ago
08e4651ece
Corrected cyrillic font again
...
Thank you @Nprod.
10 years ago
752c804677
remove offset, add minimum scan area
10 years ago
14f0250853
allow negative values
...
and some more comments
10 years ago
e6cb8ee188
Remove 6x9 font
...
in dogm_lcd_implementation.h
by using standard font and
shifting down temperature displays by one pixel
Saves 2300 bytes.
10 years ago
e93eb3e8d3
Update test
10 years ago
b8ae3feb9e
Update test
10 years ago
3570447ded
Fix Z_RAISE_AFTER_PROBING
10 years ago
8a739b6fba
Merge branch 'Development' into delta_auto_bed_level
...
Conflicts:
Marlin/Marlin_main.cpp
10 years ago
7629c4f05c
Cleanup for menu optimization
...
- Compare pr_char to space
- Fewer calls to lcd_strlen
10 years ago
3405f85a6a
Reduce size of menu code
...
- Get rid of _selected functions, passing selected state instead
10 years ago
e983a5ab92
Disable option. Enable for use/test.
10 years ago
f34b9c83d1
Added comment about MESH_NUM axis points.
10 years ago
a686c9878f
Move TOPO_ORIGIN define to Configuration.h
...
- Addressing issue #1608
10 years ago
8005d22c81
Added menu option for bed leveling.
10 years ago
0e51e53813
WIP. Adding bed leveling code.
10 years ago
d0d12962e0
Merge pull request #1615 from AnHardt/fix-1611
...
Fix #1611
10 years ago
f0dcea7e14
Fix #1611
...
Warning: suggest parentheses around comparison in operand of &
pretty much helped.
10 years ago
28b1c37dea
Fix for #1612
10 years ago
a8c1bdabd2
Update: readme.md for K8200 example
...
* readme.md: updated typo and URLs
10 years ago
2f374f1465
Removed Kanji.
10 years ago
5efc798642
Merge pull request #1546 from apollo-ng/pr-felix
...
Added support for Felix 2.0/3.0 printers
10 years ago
b83e52e50f
Merge pull request #1467 from thinkyhead/marlin_configurator
...
Configurator utility
10 years ago
7bc77dc134
Merge pull request #1583 from galexander1/m404fix
...
M404 should not use 'N' address as parameter because 'N' is reserved
10 years ago
b80ed51fcc
Fix controllerFan() code
...
- Add support for 4th extruder
- Fix parentheses matching
- Apply coding standards
- Address issue mentioned at #1575
10 years ago
4b50205f11
Merge branch 'Development' into marlin_configurator
...
Latest upstream changes
10 years ago
bb4cb1b15a
Merge pull request #1606 from thinkyhead/cleanup_stepper
...
Cleanup of stepper.cpp
10 years ago
63f41f56f8
Merge pull request #1607 from chris-bo/Development
...
Update ultralcd_st7920_u8glib_rrd.h
10 years ago
4eabd80025
Fix babystep for extruder_duplication
10 years ago
d3259d0dba
Merge pull request #1581 from msutas/Development
...
Filament Runout Sensor Feature
10 years ago
25c4f17e5d
Corrected Cyrillic fonts. Round II.
10 years ago
b73ba26b23
Update ultralcd_st7920_u8glib_rrd.h
10 years ago
c37f7d15c9
- Rename WRITE_E_STEP for consistency
...
- Add BIT and TEST macros
- Add _APPLY_ macros to stepper.cpp to help with consolidation
- Consolidate code in stepper.cpp using macros
- Apply standards in stepper.cpp
- Use >= 0 instead of > -1 as a better semantic
- Replace DUAL_Y_CARRIAGE with Y_DUAL_STEPPER_DRIVERS
10 years ago
44a205d9d9
Corrected Cyrillic fonts.
...
Cleaned typo in language_test.h Cyrillic part.
10 years ago
4d878b9bac
Fixed path typos in README
10 years ago
12ec557a75
Added DEFAULT_TRAVEL_ACCELERATION
10 years ago
1d25d510bc
Upstream Merge Fixes
10 years ago
a89d690b77
Merge remote-tracking branch 'upstream/Development' into pr-felix
10 years ago
cb57fc727d
Declare pid_output for PIDBEDTEMP
10 years ago
3d6deb9bdf
Simplify manage_heater
...
- Make separate get_pid_output(e) and get_pid_output_bed() function
- Reduce size of manage_heater function
- Hopefully work around linker errors
10 years ago
730497aaa1
Make use of ligatures in language_kana_utf8.h
10 years ago
3240d89f7d
Logic cleanup in utf_mapper.
10 years ago
2f3c77b751
Fix decimal places in G29 Bed Equation Coeficients
10 years ago
96f8d20f2f
Change selection logic another time
...
Automatic selection was to unflexible.
Updated documentation
Updated language files to new logic and documentation.
Updated bdf2u8g.exe
10 years ago
76da32b567
add hash-bang for python3
10 years ago
2e7ba44633
some renaming for readability
10 years ago
352aa3f4c5
Merge branch 'Development' into marlin_configurator
...
Latest upstream
10 years ago
e3ca9137b5
Fix missing temp_error declarations
...
- Fix for #1591 replacing #1595
10 years ago
0620267ebb
g29 auto-mode for the new G29 LRFB
...
short:
this script scans the first few lines from a gcode. If the line between 2 different z are greater than min_g1 this is our first layer. On this layer we search the min and max values of X and Y. With an offset we write that in a new file.
10 years ago
08694339eb
Merge branch 'Development' into marlin_configurator
...
Conflicts:
Marlin/Configuration.h
10 years ago
e4d77a6313
Merge pull request #1554 from 2PrintBeta/Development
...
Macro indirection for stepper drivers + Support for TMC26X and L6470 Stepper Drivers
10 years ago
b373826428
Merge pull request #2 from MarlinFirmware/Development
...
update
10 years ago
5bafb1fe1f
Add user test to language_test.h and make it default.
...
Improve description in Configuration.h
10 years ago
c0b6075f77
Fix max acceleration limits in planner
...
The max acceleration limiting was in wrong place.
10 years ago
9157cbd8f3
Add Travel Acceleration and change the M204 options
...
Added option to set Travel Acceleration (non printing moves).
The M204 options was a non sense (S for printing moves and T for retract
moves).
It has been changed to:
P = Printing moves
R = Retract only (no X, Y, Z) moves
T = Travel (non
printing) moves
I will add this info o G-Code wiki in reprap.org. I also advise to put
this info in Marlin next version changelog.
10 years ago
888cf161bd
fix travel speed option for G29
...
I forgot to enclousure the variable with #ifdef
10 years ago
af63b54562
Add travel speed option to G29 command line
10 years ago
817751d4b9
Added new languages, the Cyrillic display and a test language to find out your hardware.
10 years ago
c4b0087f7a
Insert utf_mapper.h
...
Top -> down
- Decide what output function is to use.
- Precautions. If non of the DISPLAY_CHARSET_HD44780's is selected fall back to Japanese.
- When we are not on the dogms setup a mapping table depending on display type and mapper.
- If we are on dogm we use ONE To ONE mapping - except kanji.
- select and define one of the mapping functions.
10 years ago
b60761bcff
Removed some messages that shouldn't be translated in the Japanese files.
...
And made falback to kana work.
10 years ago
97ae3c5c6a
Corected some errors inrtoduced by a faild global replacement.
10 years ago
ae76b1e8a8
Changes in dogm_lcd_implementation.h in detail.
...
Top -> down
- We don't need the old Marlion_font package any more - we made new.
- But we need information about configured fonts and the mappers.
- We support Cyrillic now.
- LCD_CLASS is not used in this file. LiquidCrystalRus.h is deleted anyway.
- define some fonts
- BIG_EDIT_FONT works only together with western languages.
- Select a matching FONT for the MENUE depending on the defined language.
- Number the different font-types. Wanted to avoid to store complete font-structures when changing fonts back and forth.
- Marlin special symbols are now at the lower end - like in 'ultralcd_implementation_hitachi_HD44780.h'
- insert the new remembering setFont function.
- insert the new counting lcd_print functions.
- make use of the new setFont and lcd_print functions.
- On some places redefined one character long strings with chars to avoid overhead and reduce warnings.
10 years ago
5bf42066fa
Fix typo in configuration.h
10 years ago
8a4b62d081
Set more regular setup in configuration.h
10 years ago
255ca68123
Changes in ultralcd_implementation_hitachi_HD44780.h in detail
...
Top -> down:
We don't need LiquidCrystalRus.cpp and LiquidCrystalRus.h any more. Functionality is now in utf_mapper.h
Comment on LCD_STR_BEDTEMP about behaviour in strings.
Change LCD_STR_ARROW_RIGHT from "\x7E" to ">" because "\x7E" is only ARROW_RIGHT on displays with DISPLAY_CHARSET_HD44780_JAPAN.
Introduce the counting UTF8 enabled lcd_print functions.
Replace the old lcd.print functions and make use of them.
A bit of reformatting around the changes.
10 years ago
60ceca1bc1
Add speed configuration for home-bumping movement
10 years ago
6fc2ccd568
Make use of new remenbering fontswitch.
10 years ago
0f26f3abf2
Add a test_language.
...
Will show the compleet utf8 or ASCII charset
To se the second half of ASCII click on "01234..."
10 years ago
901cf203fe
Add legal stuff to marlin_kanji.h
10 years ago
2d5134b0ed
Introduce - clean - prepae language files
10 years ago
d813090d90
Merge remote-tracking branch 'remotes/upstream/Development' into Development
...
Conflicts:
Marlin/Marlin_main.cpp
Marlin/stepper.cpp
10 years ago
c321c97f35
Merge pull request #1584 from galexander1/stringcleanup
...
fix a handful of cases where strtod() was cast to int, instead of just using strtol()
10 years ago
53abc5e2f1
Merge branch 'Development' into delta_auto_bed_level
10 years ago
956fb2d278
Merge pull request #1 from MarlinFirmware/Development
...
update
10 years ago
978dadf806
Base64 decode AJAX-fetched text properly
10 years ago
0eae9c24bc
Merge pull request #1582 from galexander1/deltaconftypo
...
fix typo in delta example config introduced in commit 697ee2d
10 years ago
624f23f550
Merge pull request #1575 from Wurstnase/fix-controllerFan
...
Fix controller fan
10 years ago
424c747fb3
Enable M401 and M402 for deltas with allen key z-probes.
10 years ago
0d593ab7c1
Fix debug message
10 years ago
3e8c5678f5
fix bug where, i.e., "G1X1E1" would be interpretted as "G1 X10 E1",
...
because strtod() will read the E address value as if it was a base 10
exponent.
10 years ago
ed7874b4e0
M404 should not use 'N' address as parameter because 'N' is reserved for the line number
10 years ago
b9dfa5cad4
use code_value_long() instead of (int)code_value()
10 years ago
901b03d020
use strtol() instead of strtod() when an integer value is desired
10 years ago
4fba7b084f
fix typo in delta example config introduced in
...
commit 697ee2dc50
10 years ago
cfc6a3a87a
Filament Runout Sensor Feature
...
With this change a mechanical or optical switch may be used to check the
availability of the filament and when the filament runs out an M600
(filament change) command is issued. This is only done while printing
with an SD card.
This feature was requested several times (issue #679 ), but the requests
were not accepted since it was believed that this situation should be
handled at host side. However during an SD print the control is totally
on firmware and I think that during an SD print it should be handled by
the firmware.
The original code was posted at reprap forum
(http://forums.reprap.org/read.php?1,297350 ) by Lazymonk. I have only
corrected some bugs of the code and improved it by adding definitions to
the configuration.h in order to make it more standardized.
10 years ago
e6862700af
Add Z_RAISE_AFTER_PROBING to all config files
10 years ago
39d255608d
Test an extra delta configuration with auto bed leveling code paths
10 years ago
7c24b97958
Ported over Johann Rocholl's improvements for delta printers:
...
- Nonlinear auto bed leveling code (includes G29, G30, Z_RAISE_AFTER_PROBING). Cleaned it up to be a delta-specific AUTO_BED_LEVELING_GRID code path.
- Allen key z-probe deployment and retraction code. Cleaned it up and added safety checks.
10 years ago
a5342c942e
Update Marlin_main.cpp
10 years ago
0f3b7d5575
Update annotated configurations
...
- Also update base configs
10 years ago
c5aa56bc4d
Merge branch 'Development' into marlin_configurator
...
Latest upstream commits
10 years ago
d085725c86
More sanity-checking for ABL
...
- Moved sanity-checks to Marlin_main.cpp
- Applied to other configuration files
- Fixed formatting of ABL output
- Passing verbose level to probe_pt
- Miscellaneous cleanup
- Put CONFIG_STEPPERS_TOSHIBA into Configuration.h
10 years ago
8b6766b37b
Merge branch 'Development' into marlin_configurator
...
Latest upstream changes
10 years ago
9eed8c8cf0
Make sure a ROM is selected for ULTRA_LCD
10 years ago
7136268273
Added 'dogm_font_data_6x10_marlin_Kanji.h'
...
This is copied from http://www.thingiverse.com/thing:664397
// Japanese Original font
// Version 0.1 by ichibey
//
// 営利目的で利用する際は、かならず許可を得てください。非営利の場合は、CCライセンスに従い使用ください。
// http://creativecommons.org/licenses/by-nc/2.1/jp/legalcode
This font is very special. It uses a mixture of katakana an kanji symbols, uses multi character symbols and is only addressable by '\xxx' sequences.
10 years ago
16e173e167
Added 5 new font.h files to main directory.
...
The former place of 'dogm_font_data_6x9_marlin.h' was in 'dogm_font_data_m0arlin.h'.
Deleted 'dogm_font_data_marlin.h'.
10 years ago
254970c92a
Merge pull request #1570 from C-o-r-E/escape_fix
...
Fixes gCode handling of comments and escaped characters
10 years ago
25dc79f124
Remove M48 credits also
10 years ago
34e51f576f
Fix compile error in gcode_G29
...
- A redo of #1576 , which missed topo_flag
- Always set verbose_level
10 years ago
b14270b029
Added font tools
10 years ago
fe2bd237d5
Add font sources.
...
Fonts have been created with fony.exe (http://hukka.ncn.fi/?fony )
The HD44760_? fonts simulate the fonts of the character based displays.
The ISO10646 fonts provide the right size of the standard fonts.
Marlin_symbols contains only the the special symbols of the original marlin font.
10 years ago
344a12bd10
Merge pull request #1571 from AnHardt/Undubble
...
Undubble MSG_MIN & MSG MAX
10 years ago
1149c24b86
More grouping, cleanup, start on overrides
10 years ago
62bd734612
fix controllerFan() for inverted enable pins
...
add ```^ !(n_ENABLE_ON)``` for each stepper
10 years ago
3024f6c706
Undubble MSG_MIN &MSG MAX
10 years ago
63b62d8d4e
Fixed in-line comments and escaping
...
* "G1 X1 ; test" was not executing "G1 X1" due to never leaving comment mode.
* "M117 Hello \;)" printed "Hello \" to the display due to not replacing serial_char properly.
Tested with the following commands:
* M117 Hello ; test => displays "Hello" on display, ignores "test"
* G1 X1 ; foo => moves 1mm in X, ignores "foo"
* ; test => completely ignored, not even acknowledged
* M117 Hello \;) => displays "Hello ;)" on display
* M117 Hello \\;) => displays "Hello \" on display, ignores ")"
10 years ago
99fb1bc3e8
Attempt to resolve #1568 and add basic escape character support
10 years ago
fad14ae7eb
Merge branch 'Development' into marlin_configurator
...
Latest upstream changes
10 years ago
cdc38aa783
Move gcode handlers into inline functions
10 years ago
6d9e9a6bef
Merge branch 'Development' into enhanced_g29
...
Latest upstream changes
10 years ago
4db2179f5c
Include 4th extruder support
10 years ago
f90a947e65
Fix autoretract
...
Autoretract was broken, looks like it was overlooked when the retracted flag was updated for multi extruders.
10 years ago
2ef6b3d57a
Fix wrong defines, broken syntax
10 years ago
08b722b635
Merge pull request #1555 from C-o-r-E/solenoids
...
Add support for solenoid articulated extruders
10 years ago
32744d41a9
Do sanity checking on LRFB values
...
- Setting boundaries based on configured limits, contrasting with G28
(which forgets these limits?)
10 years ago
0a7d85c20e
Minor fixes
10 years ago
48e3a97a18
Removed extra encoder definitions from pins_FELIX2.h
10 years ago
d052a3c6aa
Merge pull request #1551 from thinkyhead/redundant_encrot
...
Cleanup rotary encoder encrot* defines
10 years ago
d8eeddfb93
Updated DUAL Extruder config, added README and enabled NEWPANEL by default
10 years ago
b423b90c77
Added Configuration_adv.h to examples for LCD/SD Support
10 years ago
075507fb9a
missed one X_ENABLE_PIN
10 years ago
dfb38874f8
Some suggested changes for #1555
10 years ago
7f8ea7105f
Arrange ProbeAction values bitwise
10 years ago
7684721977
Enhanced G29
...
- Adapted “Enhanced G29” code referred to in #1499 and posted at
[3dprintboard.com](http://3dprintboard.com/showthread.php?3105-Auto_Bed_
Leveling-Enhanced-G29-command)
- Compatible with current G29 while adding some new arguments
- `V` sets the verbose level for serial out
- `T` (or `V` > 2) send a Topology report to serial out
- `E` works the same way as before
- `P` works as before (source used `n` or `U`/`u`)
- `L`, `R`, `B`, `F` work as before
- Still needs sanity checking for `LRBF`
10 years ago
874d3d3fc5
Add support for solenoid articulated extruders
10 years ago
7540a81106
Minor fixes
10 years ago
a375d648c7
Merge remote-tracking branch 'upstream/Development' into Development
10 years ago
4a7aca2736
Merge remote-tracking branch 'remotes/upstream/Development' into Development
10 years ago
715104e477
Fix Endstop check for CoreXY bots.
...
The X_Axis could not home to min while Y_Max endstop was trigged.
10 years ago
e428e8da75
Merge pull request #1552 from thinkyhead/cleanup_cardreader
...
Cleanup of cardreader.*
10 years ago
20e59dc61e
Don't skip files starting with underscores
10 years ago
f171656f8e
Cleanup of cardreader.*
...
- Apply standards to cardreader.*
- Fix minor issues with cardreader.cpp
- Apply standards to some other stale regions
10 years ago
f379edca78
Cleanup rotary encoder encrot* defines
...
The encrot values are used in only one place, and don’t vary, so remove
redundant references.
10 years ago
c7cdb176c8
Merge branch 'Development' into marlin_configurator
...
Latest upstream changes
10 years ago
49f471a5fc
Merge pull request #1541 from thinkyhead/fixup_temperature
...
Cleanup of temperature code
10 years ago
f2710e11d1
Optimize initial loading, code cleanup
10 years ago
558c6313f7
Merge branch 'pr-felix' into Marlix
10 years ago
08bc723a3c
Enable PIDBED
10 years ago
e487bd642b
Updated PR to streamline integration
10 years ago
2eeb241b42
Find fields that group together
...
- Do field grouping
- Tweak configurations for better grouping
10 years ago
e30bfedce4
Fix undefined *_PROBE_BED_POSITION error
10 years ago
3eafea840d
Minor fixes in Configuration.h
10 years ago
c7fb1b70f2
Initial Configuration.h for Felix 2.0/3.0
10 years ago
2e172f38bd
Added support for Felix 2.0/3.0 printers
10 years ago
f994729999
Parse and use dependent groups
...
- Parse #if, #ifdef, etc. for rules to enable fields
10 years ago
9b50ec6512
Panel One encoder pins
10 years ago
838a22de64
Fix switch value method, make app global
10 years ago
8d5839151b
Merge branch 'Development' into marlin_configurator
...
Latest upstream changes
10 years ago
443e7edef4
- Add support for L6470 Drivers.
...
- Both TMC, L6470 and pin-driven drivers work.
- All can be mixed and matched as needed.
10 years ago
1db02c2891
Merge branch 'Development' into fixup_temperature
...
Merge upstream changes
10 years ago
a99470fbb0
Merge pull request #1527 from maverikou/panel_one
...
Added support for PanelOne from T3P3.
10 years ago
5727cb3ed4
Cleanup TMC Stepper a bit.
10 years ago
a5bbd402bf
Merge pull request #1539 from AnHardt/dummysensor
...
Extend the idea of dummy temperature sensors.
10 years ago
1a7b0d9a37
Redo HAS_* macros to fix define error
10 years ago
864dddc878
Macros to the top, a few HAS_* macros
10 years ago
227ab8c665
Merge pull request #1503 from MarcelMo/patch-2
...
Support for simple customisable AutoZProbing area
10 years ago
fd1ea9d56f
Move literal strings to language files
10 years ago
8742b6bd56
Merge branch 'Development' into panel_one
10 years ago
aa9c1f1bed
Better name for ADC macro
10 years ago
9c9726d469
Cleanup of temperature code
...
- Reduce calls to millis()
- General cleanup of manage_heaters
- General cleanup of pid autotune
- Formatting here & there
- Macros to clean up and shrink ISR code (reduced by ~364 lines)
10 years ago
c6d2ebe452
Extend the idea of dummy temperature sensors.
...
Added a second sensor and made them configurable.
10 years ago
c9a3eb0c1a
Spacing in calculate_volumetric_multiplier(s)
10 years ago
2af559cca3
Shared function for menu_edit_* and menu_edit_callback_*
10 years ago
df8c51528f
Merge branch 'Development' into cleanup_ultralcd
...
Latest upstream changes
10 years ago
517f411999
Spacing adjustment to menu_edit* macro
10 years ago
4938ae5caf
Add required backslash for macro expansion
10 years ago
e182cdebf9
Add required backslash for macro expansion
10 years ago
fa4c36df68
Fix menu callback issue wrt LCD_CLICKED
10 years ago
0cf0c20532
Optimize calculate_volumetric_multiplier
10 years ago
38500165ea
First attempt at adding TMC Driver support. May need some cleanup.
10 years ago
b55995aae8
Introduce a layer of macro indirection to all stepper pins. This allows other stepper drivers to redefine them, so they can use SPI/I2C instead of direct pin manipulation.
10 years ago
8ccdac9898
Enable PID debugging for heated bed
10 years ago
29097b0ab2
Enable PID debugging for heated bed
10 years ago
21bd4fd6db
Enable PID debugging for heated bed
10 years ago
fb56aad898
Enable PID debugging for heated bed
10 years ago
08c543f8fb
Enable PID debugging for heated bed
10 years ago
c89413db1e
Enable PID debugging for heated bed
10 years ago
1c71e4751a
Enable PID debugging for heated bed
10 years ago
a9e15aa503
Updated example configurations
10 years ago
3ba47ea277
Remove test/demo multi=line code menu items
10 years ago
c1240f23dd
Merge branch 'Development' into marlin_configurator
...
Latest upstream changes
10 years ago
a57869ba49
Dummy Thermistor Table for testing purposes
...
Am I the only one who always need to change the thermistortable.h to add
a dummy table??
Ok, it is done. Just set the thermistor to 999 and it will always read
25C. Great for Testing or Development purposes.
10 years ago
2e166f5337
Added support for PanelOne from T3P3.
10 years ago
40ef472a25
Merge in encoder multiplier
10 years ago
1c13cd604b
Formatting in babysteps defines
10 years ago
3a26804d80
Adapt to latest PID code and fix typos
10 years ago
422582da71
Prep formatting for upcoming PR
10 years ago
27ac3e985d
Add options to example_configurations
10 years ago
0d6a7a2df0
Merge with latest upstream changes
10 years ago
c7a97e18b7
Merge branch 'Development' into cleanup_ultralcd
...
Latest upstream changes
10 years ago
6d5c13df74
Merge pull request #1520 from thinkyhead/fixup_temperature
...
Fix typos in checkExtruderAutoFans
10 years ago
5b9e341222
Merge pull request #1516 from thinkyhead/fixup_ramps
...
Cleanup ramps boards
10 years ago
57bc28b42c
Cleanup and fix ultralcd.cpp
...
- Fix bug in lcd_control_temperature_menu
- Remove test menu-item left in from multi-line command feature
- Replace literals with translatable strings
- Reduce lcd_preheat code redundancy
- Reduce menu macro redundancy
- Clean up formatting
10 years ago
4fcd4b444e
Merge pull request #1519 from thinkyhead/fix_recent_issues
...
Fix implementation of PID menu items
10 years ago
9c35ed149d
Merge pull request #1508 from AnHardt/iss1492
...
Fix iss#1492
10 years ago
430c4b6538
Replace missing backslash
10 years ago
3aa5f98b64
Download all as ZIP, adjust layout on resize
10 years ago
a8939eec28
Readability of MENU_MULTIPLIER_ITEM
...
Last commit before bed.
10 years ago
09e09b308e
Tweaky spacing adjustments
10 years ago
e3fd3e8fa4
Fix typos in checkExtruderAutoFans
10 years ago
c610471b0c
Add PID_PARAMS_PER_EXTRUDER conditional
10 years ago
2d6fa9ce80
Proper implementation of PID menu items
...
- Make this work per #1344
10 years ago
b8e79dce89
Fix compilation errors when encoder multiplier is disabled
10 years ago
65e1fc71be
Add encoder rate multiplier
10 years ago
859c8d3fef
Azteeg X3 overrides too
10 years ago
7891eacf21
Merge branch 'Development' into fixup_ramps_boards
...
- Also apply cleanup for #1514
10 years ago
1600506545
Merge remote-tracking branch 'upstream/Development' into marlin_configurator
10 years ago
5d0c93ae10
Keep config boxes in view on wide screen
10 years ago
335b7680c9
Tooltip code, widescreen layout, hide auto-expands
...
Slightly better layout for wide screens.
10 years ago
15b73386b5
Add pin definitions for the Boards BAM&DICE + BAM&DICE Due
10 years ago
08c236059e
Merge pull request #1505 from thinkyhead/issue_1499
...
Bed leveling probe behavior issue?
10 years ago
f238c7428d
Merge branch 'Development' into marlin_configurator
...
Latest upstream changes
10 years ago
da275c72ab
Cleanup Github reply.data.content before atob()
10 years ago
159196d1e9
Reset Alert message when finish M600 command
10 years ago
266ff227cf
Merge pull request #1510 from docdawning/Development
...
Trivial spelling correction
10 years ago
dfd4e74a5c
Trivial spelling correction
10 years ago
6cdcd6c6d1
Fix iss#1492
...
Introduced lcd_strlen() and lcd_strlen_P().
Replaced the old functions where necessary.
Reworked language_ru.h.
Speeded up test for zero length string in cardreader.cpp
10 years ago
c033904693
Updated config file section markers
10 years ago
84a87a5b1c
Fix up configs a little
10 years ago
63a5ff7ab9
Merge pull request #1489 from tommil/Development
...
Updated Finnish language file
10 years ago
efb0491d40
Merge branch 'Development' into issue_1499
...
Merging latest upstream changes
10 years ago
8309b4f408
Merge branch 'Development' into marlin_configurator
...
Merging latest upstream changes
10 years ago
961998cf91
Merge pull request #1496 from thinkyhead/issue_1493
...
Megatronics 3 servo pins
10 years ago
b71322e793
Issue #1504 – K8200 Z_ENABLE_PIN
...
- K8200 uses a non-standard RAMPS with Z_ENABLE=63 ??
- Assuming from previous input that 3DRAG is the same.
10 years ago
978d114c73
Bed leveling probe behavior issue?
...
The `float` keyword should not be on these vars because they conceal
the outer vars, preventing them from obtaining known values before
being passed in `set_bed_level_equation_3pts`. Possibly related to
`Z_RAISE_BETWEEN_PROBING` not functioning.
10 years ago
7c6236761a
Merge branch 'Development' into issue_1493
...
Merging latest upstream changes
10 years ago
9875352dd8
Merge branch 'Development' into marlin_configurator
...
Merging latest upstream changes
10 years ago
d28f5b9e82
Support for simple customisable AutoZProbing area
...
When probing PCB´s I had the problem that i needed auto-leveling for specific areas (it´s never the same size).
Not much code, but very useful.
Now I use simply G29 L5 R55 F5 B35 P3 to probe a 4x6cm PCB before milling.
I used int for values... might be wrong...
I hope this time I got the right development tree. (tried first with https://github.com/MarlinFirmware/Marlin/pull/1130/commits )
10 years ago
513ff94b89
Merge remote-tracking branch 'upstream/Development' into Development
10 years ago
83cb702e72
Config sections, multi-field values, toggles, etc
...
- Auto-detect “switchable” items where possible
- Handle switchable multi-value fields
- Add standard sections to config form
- Add section markers to configurations
- Add value options to configurations
- Remove and re-add fields for loaded configs
- Preserve sections across configs
- Preserve non-added fields
- Style added fields wider & newline by default
10 years ago
afc737ca0c
Fix CoreXY Homing Routine.
...
Fixed how stepper ISR figure it out when the head (extruder) is going to
Min or Max direction.
Added Homing to Max Endstops.
10 years ago
ec53c6309a
More fields, options in config, fix tooltips
10 years ago
68184af57b
Merge branch 'Development' into marlin_configurator
...
Latest upstream commits
10 years ago
7866fa161f
Merge pull request #1476 from Natealus/Development
...
Compiling errors with 4 Extruders defined and Viki 2 Implementation
10 years ago
ea9e49b20d
ARRAY_BY_EXTRUDERS 4th hotend PID parameters
10 years ago
d0ad8a978c
Megatronics 3 servo pins
...
- Naive implementation, assuming the data sheet pin numbers correspond
to Arduino pin numbers.
10 years ago
e74138b2be
More robust fetch code, download buttons
...
- Fetch code now handles github, local, or http: access
- Download button creates a time-stamped inline download
- More complete error messages
- Show warnings when approaching the hourly fetch quota (limit
reloading!)
- Added my test domain (where the _htaccess is deployed)
- `_htaccess` file added to set Access-Control-Allow-Origin “*”
- Marlin logo with css
- Limit selectable areas to avoid annoying selections
- Messages now persist until dismissed
- Default repo for files set to thinkyhead, ‘marlin_configurator’ branch
- Cosmetic changes
10 years ago
622a531d9c
Fixed error in translation
10 years ago
290ab42d22
Updated Finnish translations
10 years ago
22a7985445
reverted to upstream
10 years ago
b3bda57ca2
reverted to upstream
10 years ago
9d75a56b56
Merge remote-tracking branch 'upstream/Development' into Development
...
Conflicts:
Marlin/Configuration.h
Marlin/Marlin_main.cpp
10 years ago
0a59fee763
Merge remote-tracking branch 'upstream/Development' into Development
10 years ago
eb5889b3da
Merge pull request #1479 from AnHardt/en_first
...
#include "language_en.h" before the national language in language.h
10 years ago
b9ed873827
Enable PID debugging for heated bed
10 years ago
0a19109476
Enable PID debugging for heated bed
10 years ago
a4f939cc27
Updated Finnish language file
10 years ago
32d4dd073f
Merge pull request #1487 from AnHardt/iss1485
...
Fix for #1485
10 years ago
c246026bda
Sorry.
10 years ago
07e488cfae
Fix for #1485
10 years ago
e7ecf14d0c
Update ultralcd_st7920_u8glib_rrd.h
...
Fixed delay-times during Init. REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER won't get initialized on some Boards because delay was to short.
10 years ago
52c3cf6d34
Fix a logging error
10 years ago
ba24a09f24
Use api.github to get Configurations
...
- Make api.github the default source for configurations
- Remove configurations from the configurator
- Continuation and enhancements
10 years ago
f4b0a40abb
Additional fixes to temperature.cpp and found another missing line
...
Looks like INVERT_E3_DIR was missing in the configuration.h also as I
did a test compile with 4 extruders and Azteeg X3 Pro defined. So I also
added those lines too. Additional formatting to make the comments line
up better in that section.
10 years ago
3aac2df057
Now the oter way around.
...
Include of language_en.h now behind national language.
All "#define MSG_STR_*" now surrounded by #ifndef and #endif.
10 years ago
488633bf44
#include "language_en.h" before the national language in language.h
...
+ May decrease the workload for feature developers. They may omit to
update all the language files but "language_en.h". When loading _en
first, all new features give some display, but the new in English.
- May throw some additional warnings about redefinition during compile.
10 years ago
8e92729141
Make display language configurable in Configuration.h
10 years ago
38a500d05c
Viki 2 Implementation
...
I've insert the define and pointer entries for the Viki 2 and miniViki
from Panucatt in all of the example configs and main config. With these
additions and with pins done in the old single pin.h style...I was able
to get the display working fine save for needing to turn Delta Segments
per Second down. But that's a common graphics lcd issue being looked
into right now.
I need assistance in understanding how the new divided pins files fit
together because my previous attempts at trying to get it to work
appropriately didn't seem successful. This originally came from trying
to find out how to swap the XYZ Min and Max Endstop pins in the Azteeg
X3 Pro. It only comes with one set of connectors and they're Min
Endstops. My previous experience didn't turn out well trying to tell the
firmware to home to the Min Endstops so the best solution I found was to
swap the pins in the firmware. If I'm missing a conflict with a setup
other than delta please let me know, but it makes sense in my setup.
10 years ago
697ee2dc50
Compiling errors with 4 Extruders defined
...
Here were a few changes that I had to make/add lines for the 4th hotend.
A compiling problem in the Temperature.cpp and missing lines in
configuration.h and configuration_adv.h. I added these lines in all of
the example configs too.
10 years ago
85e5aa4011
Generalized enqueue_commands_P, and moved them to Marlin_main as they should
10 years ago
4228758f1d
Clean up and improve tooltips, show the name
10 years ago
0116320d2c
Strip slashes off the front of tooltips
10 years ago
69240d41b0
Offset the timing of the pulsing animation
10 years ago
78b9428f4e
Avoid capturing disabled items in comments
10 years ago
5d159851e5
Fix positioning of tooltip
10 years ago
c99f1de9f3
Fix tooltips blocking clicks
10 years ago
1a548c1bc1
Find nearby comments and make them into tooltips
10 years ago
90fa1345b0
Fix purge + refresh of define info
10 years ago
aa67b38a44
Fan speed and 4th extruder on graphical LCD
...
- Display fan speed 0-1 as “—“ and 254-255 as “100%”.
- Display 4th extruder instead of the heated bed
10 years ago
7850ae2f4f
Merge branch 'Development' into marlin_configurator
...
Merge latest Development
10 years ago
2647402095
Use info.repl in updateDefineFromField, fix regex
10 years ago
12a3975341
Close section tag, add String.prototype.lineCount
10 years ago
4bb72f9480
Highlight the edited line
...
- Add a span to the edited text line to provide a highlight
- Scroll and highlight for switch checkboxes also
- Clean up initialization
- More API documentation
- Smarter handling of asynchronous file loading during init
10 years ago
37c43a7ab3
Scroll to reveal on switches as well
10 years ago
9c0adae3cd
Scroll to setting position in file when edited
...
- Animate scrolling to the edited item’s position
- Sanity check file drops and show warnings
- Fix form init / refresh on new configuration drop
- Document the API methods that get/set defines
10 years ago
4d341bb758
Copy configs into subfolder
...
Browsers may not want to load files outside the folder, but they may be
okay with these relative references within the folder.
10 years ago
72856166a9
Fix bad typo in ConfigurationStore.cpp
10 years ago
b51204cc1c
Add fieldsets and make them into tabs
10 years ago
56769ba4f8
Make comment/uncomment a little neater
10 years ago
94bebf31ac
Pre-collect info about options on field init
...
- When initializing fields use the configuration to determine the format
- Cache the line for each option for fastest string compare / replace
- Add logging levels for debugging
10 years ago
32aaadc301
Include minimized jQuery 2.1.3
10 years ago
53f6bbdfe0
Try a stepper for the serial port
10 years ago
ac7a4358d6
Add a responsive file uploader
...
- Specify HTML5
- Allow drag and drop for loading configurations
10 years ago
09a385d9b0
Add "use strict" to the top.
10 years ago
b2627200ea
Get thermistors from config, add temp sensors
10 years ago
ef18bfdd3f
An in-place browser-based configurator utility
...
- A web form with fields for configuration values
- Reads and parses standard config files
- Modifies configurations dynamically in-place
10 years ago
3490a19103
Merge pull request #1466 from CONSULitAS/Development_K8200_de
...
K8200: Example Configuration.h fixed
10 years ago
cfbb94a2a8
K8200: Example Configuration.h fixed
...
Example Configuration.h: fixed strange white characters preventing
compilation in lines 1 and 3 - oops
10 years ago
b65c5d8ec6
Merge pull request #1464 from AnHardt/iss1448-Menu
...
Unified menu selection - by hilighting - made first column avilable
10 years ago
0de5083aff
K8200: Example Configurations readme.md updated
...
Example Configurations for K8200 readme.md updated
* readme.md: added description for german umlaut support on LCD
10 years ago
c421ffd520
K8200: Example Configuration_adv.h back in sync
...
Example Configuration_adv.h for K8200 back in sync
* Configuration_adv.h: rebased and added missing changes for 4th
extruder
10 years ago
0575dd10de
K8200: Example Configuration.h back in sync
...
Example Configuration.h for K8200 back in sync
* Configuration.h: rebased and added missing changes
* Configuration.h: updated comments for K8200
10 years ago
f708884808
Introduced new function lcd_implementation_mark_as_selected()
...
New function now drops the prechar (select character) and makes the first
column usable for text.
Marking the line is now constantly made by highlighting (reverse).
Replaced selection code in:
lcd_implementation_drawmenu_generic()
_drawmenu_setting_edit_generic()
_drawmenu_sd()
with new function.
10 years ago
b6ca50a2cc
Merge pull request #1463 from thinkyhead/cleanup_recent_merge
...
Apply some cleanup for recent merge
10 years ago
cc56f36870
Merge pull request #1461 from thinkyhead/issue_1453_redo
...
Apply fix for M600 filament change
10 years ago
8663f4bbaf
Apply some cleanup for recent merge
...
Combine 1/(rows+1) with u8g.getHeight() to get rowHeight and just use
that.
10 years ago
0cb1029311
remove extra plan_buffer_line
10 years ago
9381bfe7f9
Fixes issue #1447 - Overlapping of long descriptions with values.
10 years ago
b97a950f53
Apply fix for M600 filament change
...
- Patch from #1453 for delta movement plan
- Fix: Set X with code X instead of adding to X
10 years ago
2abf1ad940
Distribute recent changes in Configuration.h to the examples.
10 years ago
33f8580255
Merge branch 'lcd-width' into b-
10 years ago
0c24bb6cfc
Adjust LCD_WIDTH to make better use of DOGM LCDs
10 years ago
b1dbd765c6
Centralise definition of fonts for DOGM displays
...
Prework for issue #1448 and #1447
Will merge in when pull request #1457 is in.
10 years ago
65642592ee
Added dualline version.
10 years ago
f9cc1df00b
Droped URL from bootsplash.
10 years ago
c20606b8d7
Replaced some literal constants with defines
...
Replaced calculation to centre bitmap with fixed values.
Saved 20 bytes.
10 years ago
3602474c25
Replace solitaire use of u8g_font_5x8 font and replace with u8g_font_6x10_marlin
...
and win another 1694 bytes.
10 years ago
f5fd94d62a
Kick suspicious loop an win 72 bytes.
...
No visible impact.
10 years ago
b3973ed224
Fix HD44780 misspelled as HD44870
10 years ago
d8b7f29fa2
Merge pull request #1452 from thinkyhead/fix_M200_bug
...
M200 cleanup, normalization of EXTRUDER loops
10 years ago
6d81968db5
Merge pull request #1450 from docdawning/Development
...
Normalized section headers, added some headers, added help URLs for newb...
10 years ago
5bb3933b21
Fixed n00bsauce
10 years ago
d109cd940b
Normalized all configuration files to include my new section headers and the like.
10 years ago
055c4beaf9
Normalized section headers, added some headers, added help URLs for newbies
10 years ago
9dc5de6166
Hide code that makes veteran geeks go "aha!"
10 years ago
bd387068bb
Apply loops for extruders elsewhere also
10 years ago
4a146d584b
Loop, since the pending feature can use an array
10 years ago
bca884bf72
Realized it's not a bug, but cleanup code anyway
10 years ago
2dd43a82b1
Ups. #else added
10 years ago
26e55471f8
Update example configurations.
10 years ago
85385be132
Removed now automatic define of DISPLAY_CHARSET_DOGM + improved description.
10 years ago
0e40408ee5
Make exemplaric use of new display charsets in language_en.h and languag_de.h
10 years ago
8dce5a6644
Improve new charset featur.
...
Select DOGM-displays automaticly.
Give hint where to find charsets.
Add '²' and '³' characters.
10 years ago
c009c81e65
make marlin-main the default
10 years ago
f4ebc02555
marlin url
10 years ago
0af9a0bf57
url to firmware downloads
10 years ago
5f8dd92905
toss in a fix for .ru
10 years ago
3f3ad9b3ad
typo
10 years ago
07639053fb
Add support for BQ Prusa i3 "Hephestos"
10 years ago
fb7c636ecf
Avoid compiling error
...
Only a missing ","... now it will compile again
10 years ago
787d6fb61a
Update RUMBA pins file
...
Add FAN1_PIN and SERVO0_PIN
10 years ago
5fd5105d44
Merge pull request #1439 from clefranc/Development
...
Fix nozzle in temperature menu
10 years ago
76bf93efcb
Revert "get STR_THERMOMETER from ultralcd_implementation_hitachi_HD44780.h"
...
This reverts commit 4d5b0e2037
10 years ago
4d5b0e2037
get STR_THERMOMETER from ultralcd_implementation_hitachi_HD44780.h
10 years ago
33408a4dfc
Update ultralcd.cpp
...
Fix number of nozzle displayed in temperature menu.
10 years ago
6e6e3cf443
merged https://github.com/MarlinFirmware/Marlin.git
10 years ago
b3ca430a20
Inducted the defined placeholders in the translation table.
10 years ago
e045034c3f
Included Configuration.h to read the defined charsets.
...
Defined the charsets plus a default.
10 years ago
27c638803e
Defined three charsets.
10 years ago
073c59c50a
Clean up some formatting
...
- Also partial cleanup of Marlin_main.cpp with a smidgen of Doxygen.
10 years ago
9a4d4b3a2f
translated Deltamenu
10 years ago
8aa6487b4b
MSG_ENDSTOP_ABORT = 'Endstop abort' > 'Endstop Abbr. Ein'
10 years ago
666ad7106b
Translated redundand: define MSG_INIT_SDCARD and MSG_CNG_SDCARD
10 years ago
e5c45fbe8c
Infoscreen messages end with a '.' if not to long.
...
MSG_NO_MOVE = 'Kein Zug.' > 'Motoren Eingesch.' hat mich grau Haare gekostet.
Die englisch Meldung will sagen - Du kannst jetz am Extruder arbeiten, die
Achsen sind bockiert, die Motoren sperren die Achsen weil sie unter Strom
stehen, weil sie eingeschaltet sind.
10 years ago
1e22137e27
MSG_STOP_PRINT = 'Druck stoppen' > 'SD-Druck Abbruch'
...
to work out that this can't be resumed.
10 years ago
05d2ebd118
MSG_WATCH > 'Beobachten' > 'Info'
10 years ago
06cba91c39
eye candy 2
10 years ago
9352c9547f
MSG_SPEED = 'Geschw' > 'Geschw.'
10 years ago
0dfb0162f3
eye candy.
10 years ago
7222b27501
MSG_MOVE_AXIS = 'Achsen bewegen' > 'Bewegen'. Is Extruder an axis?
10 years ago
a6f808c9b1
remove unused #define MSG_RETRACT
10 years ago
152fa579f5
MSG_SWITCH_PS_OFF = 'Switch Power Off' -> 'Netzteil Aus'
10 years ago
7a32b742f3
MSG_SWITCH_PS_ON = 'Switch Power On' ->'Netzteil Ein'
10 years ago
4e176d2ce8
MSG_SET_ORIGIN = 'Setze Nullpunkt' ->'Setze Null hier'
10 years ago
1f8c8ad3ed
MSG_SET_HOME_OFFSETS = 'Set home offsets' ->'Setze Home hier'
10 years ago
0e8836ce5e
MSG_AUTO_HOME = 'Auto Nullpunkt' ->'Home'
10 years ago
56d3e6615d
MSG_DISABLE_STEPPERS = 'Stepper abschalt.' -> 'Motoren Aus'#
10 years ago
1258980832
Merge pull request #1429 from bq/Development
...
Add bq Witbox 3D printer
10 years ago
766762a4dc
Change url link
10 years ago
7df9ca051c
Merge pull request #1428 from thinkyhead/issue_1388_eeprom
...
Make EEPROM storage consistent
10 years ago
fe3810f073
yeah, what he said
10 years ago
6137bbd484
use eeprom read correctly
10 years ago
9bc9051405
Flag EEPROM write errors on serial output
...
- Also adds a language string for the error.
- Also adds SERIAL_EOL as an alias for SERIAL_ECHOLN(“”)
10 years ago
ff99ca3040
Fix alignment of Restore following PIDTEMP
...
Should be reading 4 x 4 PID values instead of 4 x 3
10 years ago
6c285930cb
Fixing wrong pin to heater extruder 2 <-> 3
...
Extruder 2 and 3 was swapped
10 years ago
0d4ce27b79
Add pins_WITBOX file
10 years ago
13118cde33
Add bq Witbox 3D printer
10 years ago
093fedfde8
Make EEPROM storage consistent
...
Update ConfigurationStore to always write dummy values for disabled
options, including FWRETRACT, DELTA, and SCARA. Update the EEPROM
version to “V15.” Also fixes a buffer overrun with axis_scaling in
Config_ResetDefault.
10 years ago
34377ee512
Merge pull request #1427 from thinkyhead/fewer_preheat_strings
...
Remove language strings that only add a number
10 years ago
7378a7fef4
Merge pull request #1408 from thinkyhead/cleanup_servo
...
Formatting cleanup of quiet sources
10 years ago
5fbef6bed2
Merge pull request #1409 from thinkyhead/rename_lastnr
...
Rename lastnr to autostart_index and...
10 years ago
53eea611b8
Fix MSG_NOZZLE
10 years ago
d7211a5324
Changes for Portuguese too
10 years ago
0a21727c0a
Portuguese (pt) and Brazilian Portuguese (pt-br)
10 years ago
c90f2e77d8
Remove language strings that only add a number
...
This won’t reduce the string storage in the end, but it makes the
language files smaller. Also removed remaining unused strings.
10 years ago
2ce4a102ee
Add support for Megatronics 3 a la #1426
10 years ago
ae4b348d77
Make sure _Ex_PINS is defined
...
Also fix analogInputToDigitalPin so it uses proper C hex notation
10 years ago
80be6f3f91
tweak tweak
10 years ago
ebe78cb36f
tweak
10 years ago
82474fef8a
Max endstop pins disabled by configuration
...
There’s no need to ask users to uncomment Max Endstop pins when they
have them. These will be set to -1 later if the endstop option is
disabled.
10 years ago
8045e4d60d
Add support for 4th extruder
...
#1405 includes some changes to pins.h for a 4th extruder. This commit
applies those changes. It also deals with a possible problem with
SENSITIVE_PINS.
10 years ago
df4f3e7712
cleanup
10 years ago
b6ecbd8cc4
cleanup
10 years ago
4e573134de
Cleanup heading
10 years ago
574a5ab72a
Split up pins to make it more manageable
...
Hopefully this is helpful to organization and future expansion….
10 years ago
d55c62bf9f
Update ConfigurationStore.cpp
...
Moved #endif to allow filament settings to print.
10 years ago
e779641c73
Update ConfigurationStore.cpp
...
Added PIDTEMP dummy write to align EEPROM read/write operation.
10 years ago
baac6e242d
Merge pull request #1419 from AnHardt/bootsplash
...
repair Bootsplash
10 years ago
75cf302da3
example configurations changed to meet Configuration.h
10 years ago
61fd45a0c2
Add 4th extruder
10 years ago
2650be4921
Add 4th extruder
10 years ago
a9763d894e
Add 4th extruder
10 years ago
4949088302
Add 4th extruder
10 years ago
fc5204bd42
Add 4th extruder
10 years ago
9834818ef7
Add 4th extruder
10 years ago
8696963154
Add 4th extruder
10 years ago
ee8a7419f4
Add 4th extruder
10 years ago
e18403235d
Add 4th extruder
10 years ago
7baee555f4
Add 4th extruder
10 years ago
cebc7daf2a
Add 4th extruder
10 years ago
ef4c7abb21
Update language_es.h
...
Add 4th extruder
10 years ago
22e591518a
Update language_de.h
...
Add 4th extruder
10 years ago
a20c35bb38
Update language_ca.h
...
Add 4th extruder
10 years ago
dd301be52d
Added suport for multiline G-code commands in the LCD menus
10 years ago
aa48056c03
Made centering of bootlogo work and removed contraproductiv setScale2x2() in dogm_lcd_implementation.h
10 years ago
0d219b3e14
Make centering of STRING_SPLASH work
10 years ago
59315330dd
Remove definition of VERSION_STRING and replace where usend with STRING_VERSION
10 years ago
8c792c7b22
Make STRING_VERSION and VERSION_STRING the same
10 years ago
865ca0ef04
Merge pull request #1405 from MagoKimbra/4th-extruders
...
All the additions look proper. I can't think of any other extruder-count-related items that you might have missed. So, with some optimism, I will merge this for testing.
10 years ago
3021f7f743
Fix PID_dT
...
Add PID_dT in temeprature.cpp
10 years ago
a7b02975b7
No TEMP1 or TEMP2 pins for TEENSYLU || PRINTRBOARD
...
Pins 2 and 3 are probably general-use pins, since the filament sensor
uses pin 2.
10 years ago
6723388f7f
Proposed fix to #1379 . Printrboard I2C LCD support
10 years ago
03c9cb60e8
Rename lastnr to autostart_index and...
...
Replace instances of the number 13 with FILENAME_LENGTH where
appropriate.
10 years ago
ef5959a705
Fix Temperature
...
Githun insert this line when i merge with actual Branch development...
10 years ago
3d4ee6c868
Merge branch '4th-extruders' of https://github.com/MagoKimbra/Marlin into 4th-extruders
...
Conflicts:
Marlin/temperature.cpp
10 years ago
986e723eeb
Add 4th extruder
10 years ago
f16bdd2ff2
Borrow from Ultimaker to fix MAX6675 SPI conflict
...
Changes to temperature.cpp from Ultimaker fork, intended to address
#1226 and #1227
10 years ago
06c3b37933
Formatting cleanup of quiet sources
...
Formatting for code-folding plus minor style changes to less active
code.
10 years ago
23fcd1ecb2
Merge pull request #1407 from thinkyhead/cleanup_marlinserial
...
Formatting cleanup of quiet sources
10 years ago
fd78902194
Formatting cleanup of quiet sources
10 years ago
5c1814383a
Merge pull request #1390 from floyd871/Development
...
Show Custom M_Code for Z-Probe Offset when entering M503
10 years ago
0ebf896070
Add 4th extruder
10 years ago
a9d7ab9530
Update ConfigurationStore.cpp
...
Done
10 years ago
3a9a3e5ed8
Fix Issue #1356 – remove EXTRUDER1_Z_OFFSET
...
This define is not used.
10 years ago
54d5b52a2e
Merge pull request #1399 from beanz/use-bed-defines-not-extruder-ones
...
Code wont compile with extruder but without bed runaway protection defined.
10 years ago
0ce252ba7a
This ifdef is for bed code so should use bed constants for testing.
...
Without this fix, the code wont compile with extruder but without bed
runaway protection defined.
10 years ago
9040446780
Merge pull request #1395 from AnHardt/iss1394
...
removed function step_wait() from stepper.cpp
10 years ago
25f79c5010
Merge pull request #1391 from CONSULitAS/Development-newBoard_K8200
...
Add: Board for Vellemann K8200 (derived from 3Drag)
10 years ago
9ce75ab7de
Merge pull request #1386 from roglio/Development
...
Fixing a build error for melzi and gfx display
10 years ago
15a00a5a7c
Add 1µs delay in other appropriate spots
10 years ago
23cb899c5a
removed function step_wait() from stepper.cpp
...
removed function step_wait() from stepper.cpp because its used nowhere.
10 years ago
d9d4a78e0f
Add proper delay in stepper.cpp
...
Issue #1385 describes a delay that the compiler is optimizing out and
this solution.
10 years ago
d1322dafc9
Add: Example Configuration for Vellemann K8200 - based on new BOARD_K8200 #1391
...
# Add: Example Configuration for Vellemann K8200 - based on new
BOARD_K8200 #1391
* K8200: new folder in example_configurations for Vellemann K8200 (3Drag
clone - should work with 3Drag http://reprap.org/wiki/3drag , too. Please
report)
* K8200/Configuration.h/Configuration_adv.h: updated manually with
parameters form genuine Vellemann Firmware "firmware_k8200_marlinv2"
based on the recent development branch
I tested the changes on my K8200 with 20x4-LCD and Arduino 1.0.5 for
Windows (SD library added to IDE manually) - everything works well
10 years ago
3b50a5e2e6
Add: Board for Vellemann K8200 (derived from 3Drag)
...
## Add: Board for Vellemann K8200 (derived from 3Drag)
* Boards.h: updated comment for board 3Drag - K8200 removed
* Boards.h: added `BOARD_K8200` with ID 78
* language.h.: machine name and firmware URL for new board
* pins.h: added `K8200` to any `#if` with `3Drag` and corresponding
comments
10 years ago
2d454da3af
Update ConfigurationStore.cpp
...
Show Custom M Code when entering M503
10 years ago
4f35de991a
Merge pull request #1383 from CONSULitAS/Development
...
Update Boards.h for Vellemann K8200 - comment only
10 years ago
22571ca13d
Revert "Configuration for Aurora Z605"
...
This reverts commit 935ee968a7
10 years ago
935ee968a7
Configuration for Aurora Z605
...
Still not fine tuned but working.
10 years ago
ccdbeda526
Fixing a build error for melzi and gfx display
...
When a melzi board and a full gfx are both selected, the build fails
blaming for some missing defines.
This is a fix for the issue: now my configuration works.
10 years ago
e13f159343
Update Boards.h for Vellemann K8200 - comment only
...
## Update Boards.h for Vellemann K8200 - comment only
* Boards.h: updated comment for board 3Drag - K8200 uses same board
10 years ago
51c7f2fd5a
Revert "## Add: Example Configuration for Vellemann K8200"
...
This reverts commit 5333590ac2
10 years ago
5333590ac2
## Add: Example Configuration for Vellemann K8200
...
* K8200: new folder in example_configurations for Vellemann K8200 (3Drag
clone - should work with 3Drag too, please report)
* K8200/language.h: updated machine name and URL for K8200
* K8200/Configuration.h/Configuration_adv.h: updated manually with
parameters
form genuine Vellemann Firmware "firmware_k8200_marlinv2" based on the
recent development branch
* K8200/files by Vellemann: added folder with original files from
Vellemann homepage, since there is no GitHub fork you could link to by
them
I tested the changes on my K8200 with 20x4-LCD and Arduino 1.0.5 for
Windows - everything works well
10 years ago
ba3ac40b9d
Remove hardcoded programmer option (-cwiring). Use variable AVRDUDE_PROGRAMMER.
...
Change default value of AVRDUDE_PROGRAMMER to 'wiring'.
10 years ago
53f971095d
Revert "Reduce PROGMEM warnings"
10 years ago
67b597ad46
Update printrboard pin assignments
...
Backported from Printrbot branch, allows the fan to work correctly.
10 years ago
d4880a9e60
Revert "Move Sd library out into library"
10 years ago
ccdb086fc8
Merge pull request #1363 from PxT/patch-1
...
Fixes #1361
10 years ago
5151db5c2f
Merge pull request #1349 from msutas/patch-2
...
Improvement - G29 Option for Not Retracting Servo
10 years ago
1746b2582b
Merge pull request #1332 from Sniffle/Development
...
Rambo FAN_PIN documentation and servo support
10 years ago
4b51b5a46d
Merge pull request #1357 from odewdney/SDlib
...
Move Sd library out into library
10 years ago
f2cb4a3655
Merge pull request #1353 from thawkins/Development
...
fix avrdude upload in makefile
10 years ago
9fd4292923
Fixes #1361
10 years ago
f84ff4ba7d
Move SD Fat library out of main src
10 years ago
ab074dac17
Merge pull request #1344 from grob6000/independent_pid
...
Independent PID parameters for each extruder
10 years ago
d4a665694a
Merge pull request #1350 from odewdney/Development
...
Reduce PROGMEM warnings
10 years ago
9d9c859ac1
First move of SdFat library
10 years ago
5045d17a39
fix avrdude upload in makefile
10 years ago
3a5a6f42fb
Corrected the ABL grid option
...
G29 E was not retracting the probe on the last probe point when used with ABL grid. Corrected.
10 years ago
cd55a93a13
re-add blank line
10 years ago
23bfe30036
moved include themister to temperature.c
10 years ago
538859669d
Removing compiler warnings for progmem
10 years ago
bf2c923db5
Make multiple PID parameters a config option
...
* Adds config parameter `PID_PARAMS_PER_EXTRUDER` - allows single PID
parameters to be used where this would be preferable (e.g. dual
identical extruders)
* When disabled, will use `float Kp, Ki, Kd, Kc;` as before.
Preprocessor macros used to switch between.
* ultralcd.cpp defines extra menus for extra parameters only where
required
* M301 reports `e:xx` only if independent pid parameters enabled
* EEPROM structure still leaves space for 3 extruders worth, when undef
will save single parameter to all extruder positions, but only read the
first
* Switching off saves approx 330 B with no LCD enabled, 2634B with LCD
(RRD) enabled: this is significant.
* LCD modifications should be tested.
10 years ago
0877aa0fe0
Merge remote-tracking branch 'upstream/Development' into independent_pid
10 years ago
e0beb98fd3
Improvement - G29 Option for Not Retracting Servo
...
This change introduces an improvement to G29 command on Marlin.
Auto bed leveling operation's reliability is based on the repeatability of the Z-probe switch and the servo. This change introduces an option to G29 command. When the G29 command is sent with an "e" option, during auto bed levelling the servo is not retracted between probes which decreases the bias on auto bed levelling resulting from servo.
G29 command does the auto bed probing as it is.
G29 E command engages the servo on first probing point, probes all points and retracts the servo after probing the last point.
Please comment your opinions, test on your printer and check the code on a programmer's perspective. (I am not a good programmer.)
10 years ago
7d32c7f36d
Multiple PID parameter edit for ultralcd
...
* Depending on extruder count, will add menu items for ultralcd to edit
individual PID parameters for each extruder
* Added menu items to each language_xx.h
* Builds OK, but recommend testing with typical LCD
10 years ago
69dc411ae0
Merge branch 'Development' of github.com:MarlinFirmware/Marlin into LogoLCD
...
Conflicts:
Marlin/dogm_lcd_implementation.h
10 years ago
3e2af67ce3
Fix R-H compatibility
...
* R-H reads incorrect M301 line from EEPROM output if more than one is
present. Reverted to original output format, using only E0 value.
10 years ago
37c7e8300f
Independent PID parameters for each extruder
...
* Variables Kp, Ki, Kd, Kc now arrays of size EXTRUDERS
* M301 gains (optional, default=0) E parameter to define which
extruder's settings to modify. Tested, works with Repetier Host's EEPROM
config window, albeit only reads/updates settings for E0.
* All Kp, Ki, Kd, Kc parameters saved in EEPROM (version now v14), up to
3 extruders supported (same as Marlin in general)
10 years ago
326b925557
DOGLCD and LCD_PROGRESS_BAR to coexist
...
Small changes (and formatting to confuse the diff’er) which first
allows DOGLCD and LCD_PROGRESS_BAR to be enabled in tandem, then a
#warning (rather than error) that the extra progress bar / message
options don’t apply to graphical displays at this time. This leaves
open perhaps combining the progress bar and message area in some future
(or forked custom) graphical LCD display arrangement (at which time the
relevant variables may be moved into ultralcd.cpp with externs in
ultralcd.h). I also added a conditional error that the progress bar and
the filament display may not work well together.
10 years ago
1aade4a8e2
Merge branch 'Development' of https://github.com/MarlinFirmware/Marlin into Development
10 years ago
8a2e84e3f1
Possible fix for FWRETRACT with 0 zlift.
10 years ago
905aab3b85
added missing #endif
10 years ago
b9cf1465a7
updated LCD bouts with new strings and bitmaps
...
new version is pretty generic and should work in most scenarios
10 years ago
c7632be5cc
added high and low resolutions version of splash screen logo (saving code size)
10 years ago
8f0dba7cbf
adding string for bouts splash string to config
10 years ago
d94109e886
updated logo post and ver info
10 years ago
cd33b5b062
changed logo and ver info
...
logo is now 110 pixels wide and starts 9 pixels in from top left corner and also 9 pixels down from same corner... this will give a 9 pixel border all way round
ver info is placed centered and there is a 9 pixel from bottom of display to ver info
10 years ago
9b6c1cfda6
removed unneeded lines in welcome msg
10 years ago
ffa09f86f4
moved ver info 5 spaces to the right
10 years ago
2bbb68be8a
Fix calculation of BAL grid fitting into the bed
...
The previous calc was wrong. Between N points there are only N-1 gaps,
not N.
So changing AUTO_BED_LEVELING_GRID_POINTS to
(AUTO_BED_LEVELING_GRID_POINTS-1)
10 years ago
590caafa2d
changed ver info
10 years ago
3bb9b31515
changed boot logo a bit to test if fat wall goes away
10 years ago
da192c521f
Merge pull request #1333 from andrewsil1/development
...
Fix grammar/typos in new Configuration.h option
10 years ago
3a30d45c2e
Revert "issue 968 for dev branch"
10 years ago
269ec9f87f
Fix grammar/typos in new Configuration.h option
...
(For the SLOW_PWM_HEATERS option)
10 years ago
506353892e
Rambo Pin documentation and servo support
...
Updated pins reference and servo support.
cross referenced between Rambo 1.1, 1.2, and 1.3
10 years ago
8d7bfd03d8
moved/renamed documentation stuff to top-level directory
10 years ago
3c9e6b7b62
added link for pic to hex converter
10 years ago
0e760274bd
changed reprap logo to marlin logo
10 years ago
b291a422e9
added square png version of logo
...
406*406 pixels
10 years ago
7ae548cf34
Update Marlin Firmware URL
10 years ago
8f9067faa6
Added marlin logos. (Designed by Ahmet Cem TURAN)
10 years ago
addf52fd4a
Merge pull request #1328 from DinoMesina/development
...
Some corrections and new features
10 years ago
5cfe13f240
Correct some mistakes
10 years ago
c7e2d73039
Merge branch 'development'
...
ok
10 years ago
422a958a34
Fix CoreXY speed calculation
...
For cartesian bots, the X_AXIS is the real X movement and same for
Y_AXIS.
But for corexy bots, that is not true. The "X_AXIS" and "Y_AXIS" motors
(that should be named to A_AXIS
and B_AXIS) cannot be used for X and Y length, because A=X+Y and B=X-Y.
So we need to create other 2 "AXIS", named X_HEAD and Y_HEAD, meaning
the real displacement of the Head.
Having the real displacement of the head, we can calculate the total
movement length and apply the desired speed.
10 years ago
038fccd7a1
I have added some code in the "temperature.cpp" for have the possibility of control the time of the states with the heater drived by relays, with this feature now it is possible use PID function in conjunction with relay to control the temperature. I have made some tests and the temperature stay always in the range of +-1°C from the setted temp.
...
There is the possibility of turn on this features adding "#define SLOW_PWM_HEATERS" in Configuration.h
10 years ago
6730335657
Update Configuration.h
10 years ago
4ffecdbf7d
Merge pull request #1313 from wgm4321/Development
...
Re-enable filament menu with recalc fix when enabling/disabling mm3
10 years ago
672f764b4d
replaced ASCII GPL v3 license by markdown version
...
moved new COPYING file to top-level directory to make it more visible and remove clutter from Marlin subduer
10 years ago
f25e793cff
rename stepper lookup table scipt to be consistent with termistor lookup table script
10 years ago
df17a6a1b4
fix #1305 by proposed workaround (thanks gaby64)
10 years ago
f7e65935fb
make use of power operator
10 years ago
4e02aff9b5
automatically determine min/max temp for terminator
10 years ago
81363bc441
more cleanups
10 years ago
95f4a55820
refactored termistor table calculation to be in line with wikipedia's article about Steinhart-Hart coefficients
10 years ago
21205cc3d8
more cleanups in the termistorTable generation script
10 years ago
CONSULitAS