A number of regressions were patched also. The UBL G29 P2 and P4 Press and Hold had stopped working. It is very possible this is broken in the bugfix_v1.1.x branch also.
The main purpose of the Pull Request is to get the 3-Point mesh tilting to use the LSF algorithm just like the grid based mesh tilt. This simplifies the logic and reduces the code size some what. But the real reason to do it is the 3-Point case can be solved exactly. And by feeding these numbers into the LSF algorithm it provides a way to check all that code for 'correctness'.
* Fixing the DUE serial port assignments: Now -1 means the SAM3x USB Device emulating a serial port, and 0 means the USB to serial adapter included as a programming port
* Improving the Fast IO port access implementation on Arduino DUE
* Implemented EEPROM emulation on Due by storing data on the internal FLASH (with wear leveling)
* Implemented a Software SPI for the ST7920 graphics display for the Arduino RAMPS for DUE, as the default one in u8glib is clocking data too fast on ARM, and the display does not understand it.
* Fixing the case where the serial port selected is the USB device
* Adding configuration for the Makerparts 3D printer (www.makerparts.net)
* Tuned MakerParts acceleration on X and Y axis so it never loses steps. Also adjusted pulses per mm to match default hw configuration
* Fine tuned Maximum acceleration for MakerParts printer
* Style cleanup
* Style cleanup (2)
* Style fixes (3)
* Fixing the DUE serial port assignments: Now -1 means the SAM3x USB Device emulating a serial port, and 0 means the USB to serial adapter included as a programming port
* Improving the Fast IO port access implementation on Arduino DUE
* Implemented EEPROM emulation on Due by storing data on the internal FLASH (with wear leveling)
* Implemented a Software SPI for the ST7920 graphics display for the Arduino RAMPS for DUE, as the default one in u8glib is clocking data too fast on ARM, and the display does not understand it.
* Fixing the case where the serial port selected is the USB device
* Adding configuration for the Makerparts 3D printer (www.makerparts.net)
* Tuned MakerParts acceleration on X and Y axis so it never loses steps. Also adjusted pulses per mm to match default hw configuration
* Fine tuned Maximum acceleration for MakerParts printer
* Style cleanup
* Style changes to u8g_dev_st7920_128_64_sw_spi.cpp
* Even more improvements to the FastIO HAL for DUE. Now WRITE() is 2 ASM instructions, if value is constant, and 5 cycles if value is not constant. Previously, it was 7..8 cycles
* After some problems and debugging, seems we need to align the interrupt vector table to 256 bytes, otherwise, the program sometimes stops working
* Moved comments out of macro, otherwise, token pasting does not properly work sometimes
* Improved Software SPI implementation on DUE: Now it honors the selected speed passed to spiInit(). This allows much faster SDCARD access, improving SDCARD menus and reducing latency
* Update u8g_dev_st7920_128_64_sw_spi.cpp
* Disabling EEPROM over FLASH emulatiion if an I2C or SPI EEPROM is present
If using babystep to adjust the Z probe offset, the axis will move and the mesh will be updated at the same time, causing a doubling of the Z offset over the rest of the print.
To correct for this, the current Z position would need to be modified in the opposite direction, canceling out the additional Z offset added to the mesh. This would be confusing to users, and moreover it would not be accurate without also taking the current Z fade level and current Z height into account.
It might make sense to change the mesh in the case where no babystepping is taking place, but this could be considered an undesirable side-effect of changing the `zprobe_zoffset`.
One way to remedy this would be to return to storing the mesh with `zprobe_zoffset` included, then subtracting `zprobe_zoffset` from the returned Z value. Thus, a babystep moving the Z axis up 1mm would subtract 1 from `zprobe_zoffset` while adding 1 to all mesh Z values.
Without including the `zprobe_zoffset` in the `z_values` there is no safe way to alter the mesh in conjunction with babystepping, although it's fine without it.
LPC1768 VIKI2 & RRDFG are working
looks like all SPIs are working
library change
sh1106 locks up
fixed lockup, started I2C SW com
pretty
re-org
restore a few files
make library happy
switched HAL version of rrd
fix travis error
travis error fixes
another travis fix
cleanup
minor update
one more
correct spacing in platformio.ini
Move 'lcd_bootscreen()' from `lcd_init()` to 'setup()' where it is cexecute exactly once. Saves 'bool show_bootscreen'.
Move the call of 'lcd_custom_bootscreen()' to the begin of 'lcd_bootscreen()'.
Move the delays into the related functions.
Move the picture loop around 'lcd_kill_screen()' into the function.
* Re-Print of same SD Memory Card file with single click
* Re-Print of same SD Memory Card file with single click
* This is the bugfix-v2.0.0 version of https://github.com/MarlinFirmware/Marlin/pull/8104
* Add GFX overlay to UBL mesh edit
Fixed misplaced HAS_TEMP_BED in dogm_bitmaps.h
rename _lcd_babystep_zoffset_overlay to _lcd_zoffset_overlay_gfx and move it out of BABYSTEP_ZPROBE_OFFSET to we can use it for over things. Add this function into UBL mesh edit screen.
update all Configuration.h to add ENABLE_MESH_EDIT_GFX_OVERLAY
* Add Sanity to UBL insanity
Need to check for DOGLCD otherwise error out.
* Auto-enable DISABLE_REDUCED_ACCURACY_WARNING if HOME_AFTER_DEACTIVATE enabled
If HOME_AFTER_DEACTIVATE, there is no need to warn on LCD since printer will home prior to starting print. Saves 60 bytes PROGMEM on AVR with U8g panel.
* Reduce lines used
* Reduce lines used
* fixed some include paths
* LPC1768: Fix Serial API
Add missing serial methods used if TX_BUFFER_SIZE is set
Change return value of HalSerial:read to match Arduino API
* LPC1768: add filters to ADC
This is to try and compensate for hardware issue and oversensitivity to noise
* LPC1768: remove the polling section of delayMicroseconds
* LPC1768: lock usb mass storage device while device accesses it.
Currently only applicable to persistent store,
The device always has priority and will unmount the sd card from the host, Windows then tries to automount again so it can look like the explorer window freezes. Linux Mint, by default, just closes the Nemo window.
* Add timeout to make sure if Serial never connects that Marlin still boots
* Remove unneeded ifdef CPU_32_BIT
In general the need for ifdef CPU_32_BIT blocks means that something is missing from the HAL API or a Platform, in this case HAL_TICKS_PER_US was missing from the AVR Platform
* LPC1768: relocate RE-ARM debug_extra_script.py
Bob-the-Kuhn