9d11b70436
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
09b84faa00
Configuration.h, pins.h: Add MOTHERBOARD 84 for Teensy++2.0
11 years ago
e541323741
Merge https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
1c9a70cee9
Support for Gen3 Monolithic electronics
...
Techzone Monotronics support, ignoring the tip manager and using fan connector as on Sprinter FW
TODO: Add support for tipmanager
11 years ago
105bebb466
Fix for pin mapping for SDSS pin and Fan pin, so Arduino library can be used
11 years ago
97ead2eccb
Fix for microstepping pin mapping, not using Teensy pin mapping, but Arduino's default pin mapping so Arduino library can be used
11 years ago
2fa514e88a
Add port for 5DPrint D8 Driver board
11 years ago
6adbdf42e0
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
3ffc9651b1
Merge pull request #845 from DerSchultze/Sanguinololu-servo
...
Added servo pin assignments to Sanguinololu
11 years ago
73b380d8d2
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
11 years ago
dfb98101e4
Change CONTROLLERFAN_PIN for board 35 to -1, as it would conflict with board's 33 extruder pin, causing burnout (it's the same board, just different number of fans/extruders, therefore should be pin-compatible)
11 years ago
89f78b0b80
Allow use of either SD Card slot when LCD Panel is configured.
...
Preference is for Controller SD slot before LCD Panel slot when both are occupied.
11 years ago
eecda434fb
Sanguinololu servo pins set default disabled
11 years ago
06709ad60e
Added servo pin assignments to Sanguinololu
11 years ago
c9c83a4560
Updated gen3+ board pins names to current convention
11 years ago
d16a770855
Ultimainboard 2.x does not has a PS_ON pin.
11 years ago
5097c57d3a
Added pins for Azteeg X3 Pro under motherboard 68
11 years ago
b819fc53ca
Add Azteeg X3 Pro as motherboard 68
...
Add digipot i2c control for MCP4451
Allow M907 to set i2c digipot currents in amps
Fix Makefile to allow Azteeg motherboards
Fix Makefile to allow Wire libraries only
Add beeper pin for Azteeg X3 Pro
11 years ago
8d162e5bd7
Improved support for panelolu2 encoder and buzzer
...
I added #define for LCD_FEEDBACK_FREQUENCY_HZ and
LCD_FEEDBACK_FREQUENCY_DURATION_MS which is used to alter the default
buzzer sound.
When selecting Panelolu2 in configuration.h:
- it automatically sets the correct ENCODER_PULSES_PER_STEP and
ENCODER_STEPS_PER_MENU_ITEM.
- if LCD_USE_I2C_BUZZER is defined it will also set the default
LCD_FEEDBACK_FREQUENCY_HZ and LCD_FEEDBACK_FREQUENCY_DURATION_MS
When selecting the sanguinololu 1284p the following is true:
- its now enables LARGE_FLASH
- It enables the gcode M300 when the panelolu2 LCD_USE_I2C_BUZZER is
defined
11 years ago
df194f75e1
Added PT100 support for Ultiboard2
11 years ago
380144c20f
Add Ultiboard2 electronics. With PWM current settings. For the few people that have this new board as experiment in their UM-Original.
11 years ago
e8786bf110
Added support for Cheaptronic v1 electronic
11 years ago
59b96e323e
Merge pull request #640 from fmalpartida/SAV-MkI
...
Added support for BT on AT90USB devices, corrected LCD bug, added new board and LCD
11 years ago
cab84e0e5b
Add (correct) missing pin definitions for Y2
...
I tested this and it works.
11 years ago
b5a964fcc5
Initial SAV MkI (RepRap CloneWars board) integration.
...
Included support for BT dongle on AT90USB boards.
Added LCD Shift Register LCD control
Included support for RepRap Clone Wars project board (SAV MKI).
11 years ago
8a08cca0f2
Added temperature status less.
...
Hopefully fixed viky button handling without braking other boards
11 years ago
4f7c6dfe35
Update pins.h
...
Include Pins cpu Sethi 3D
11 years ago
0dca49a7c0
Added Azteeg X3 board.
11 years ago
acd8619809
Fan fix for Panelolu2+Sanguinololu.
11 years ago
53614e5144
add pins for rambo lcd
11 years ago
1902d339b0
Add Panelolu2 pins for RAMPS1.3
11 years ago
34da3a0a3f
Merge github.com:ErikZalm/Marlin into Marlin_v1
...
Conflicts:
Marlin/language.h
11 years ago
99b7e926e7
added MaKr3d Melzi board
12 years ago
2daa85918e
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin.git into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
Marlin/Marlin_main.cpp
Marlin/language.h
Marlin/pins.h
Marlin/ultralcd.cpp
12 years ago
2015989f84
Added DISABLE_MIN_ENDSTOPS
12 years ago
02dee80fa5
added Azteeg X1 motherboard
12 years ago
26a441fc7d
More 3Drag controller patches.
12 years ago
408169aef4
Merge branch 'Marlin_v1' of https://github.com/BorisLandoni/Marlin into BorisLandoni-Marlin_v1
...
Conflicts:
Marlin/Configuration.h
Marlin/language.h
Marlin/pins.h
12 years ago
bd96d22bfb
Merge branch 'Marlin_v1' into thinkyhead
...
Conflicts:
Marlin/Configuration.h
Marlin/Configuration_adv.h
Marlin/Marlin.h
Marlin/Marlin_main.cpp
Marlin/Servo.cpp
Marlin/language.h
Marlin/pins.h
Marlin/planner.cpp
Marlin/ultralcd_implementation_hitachi_HD44780.h
README.md
12 years ago
6a81291c57
Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1
...
This should fix issues with pull request 467, I hope.
Conflicts:
Marlin/Configuration.h
Marlin/Marlin.pde
Marlin/ultralcd_implementation_hitachi_HD44780.h
12 years ago
4c7d1436e9
Update pins.h
12 years ago
5dabc95409
Apply all changes from latest Marlin_V1
...
Diffed and merged, preserving my updates
12 years ago
a733537ddd
Missed some variable declarations
...
Integrated fixes from henrikbrixandersen pull request #504
12 years ago
79374f0b93
Merge branch 'reisnyderb' of https://github.com/ErikZalm/Marlin into Marlin_v1
12 years ago
5090c56651
More redundant temp sensor changes. (After testing and debugging by reifsnderb)
12 years ago
b78fa6bb70
Added support for Megatronics v2.0 and Minitronics v1.0
...
merged from code downloaded from reprapworld.com
12 years ago
7231a20dba
Put #ifdef around servo pins in pins.h. This allows the pins to be used for M42.
12 years ago
424101110c
Add Panelolu2 support for Melzi
12 years ago
dfa549f268
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
12 years ago
64360164ad
Merge pull request #482 from codexmas/Marlin_v1
...
servosupport
12 years ago
dc59f07d24
First attempt at refactoring of original servo code. Only adding servo support as a start to keep things simple.
12 years ago
9cc15876be
Add support for RUMBA thermocouple add on
12 years ago
bd2cd4903e
Added #ifdef BARICUDA around the BariCUDA changes
12 years ago
fbd899a37d
Support for BariCUDA Paste Extruder derived from MakerBot Frostruder. Using Ultimachine RAMBo board. M126/M127 and M128/M129.
12 years ago
2739c26c4f
changes:
...
- changed the variables from keypad to reprapworld_keypad
- added a missing ifdef check
12 years ago
6fb9573157
added support for the reprapworld keypad
12 years ago
b27a59f41e
Added support for Elefu RA Board and Elefu Control Panel
12 years ago
a200521eab
Added CUSTOM_MENDEL_NAME option to Configuration.h and language.h
...
Also cosmetic comment changes and spelling corrections in printed
messages
12 years ago
788d62bcc4
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Marlin.pde
Marlin/ultralcd.cpp
Marlin/ultralcd_implementation_hitachi_HD44780.h
12 years ago
4b2ece159b
Merge pull request #453 from brackendawson/Marlin_v1
...
Make Gen7 1.4+ heater temp sensort pins match silkscreen.
12 years ago
d5ee2a5a62
Make Gen7 1.4 heater pins match silkscreen
12 years ago
86867928ac
Merge pull request #434 from DDRBoxman/Marlin_v1
...
Add support for M300: Play beep sound
12 years ago
0d075378d5
Add LARGE_FLASH define and enable it for some of the beefier boards
...
The LARGE_FLASH flag allows superfluous features to be excluded
on boards with less memory
12 years ago
91bea43332
Added rumba pinout
12 years ago
aba67e2449
No bed config for RAMPS
...
The motherboard 35 is a config without bed with this pins setting :
D8 Extruder
D9 Fan
D10 Controller Fan
12 years ago
140e095c6e
Add pins for Motherboard variant 64
...
These definition contain also the definition for the graphics LCD.
12 years ago
1292d735ba
Converge all I2C LCD branches (PANELOLU2, VIKI & PCF8575)
...
This includes refactoring the buttons code to remove a large amount of
non-pin dependent duplication from pins.h.
12 years ago
12c41423ad
Fixed typo in comment
12 years ago
0995eaa492
Chenged LED_PIN for Melzi boards, added comment about broken versions of the Sanguino libraries
12 years ago
408b349a84
Fixed #368 . Commented out the wrong pin definition, but explained why it is there.
12 years ago
86358dd6cd
Panelolu pin assignment for sanguinololu from http://reprap.org/wiki/Panelolu
12 years ago
bbe7d3d0fe
Fixed #312
12 years ago
30254e3388
Merge pull request #350 from jcrocholl/Marlin_v1
...
Automatically set *_MIN_PIN and *_MAX_PIN according to *_HOME_DIR.
12 years ago
8caf5d252d
Remove bogus blank line.
12 years ago
b39f5d614a
For boards with only one endstop per axis, automatically set *_MIN_PIN and *_MAX_PIN according to *_HOME_DIR.
12 years ago
ab09fa4bbf
fixed pwm generation at pin D12 and D13 when one of them is used as FAN_PIN on Sanguino, added soft pwm entry for FAN_PIN in temperature.cpp
12 years ago
5ff5cee8ce
Fix the sensitive pin definitions, there where analogue numbers in the digital pin list. Also made M42 without a P function on the LED_PIN (which was otherwise a useless pin definition)
12 years ago
ca409e5531
Fix X/Y/Z_MIN_PIN for Printrboard.
12 years ago
33247733e0
Teensylu and Printrboard use different analog pins for thermistors.
12 years ago
6cba11f087
Stop redefining MOTHERBOARD and #define AT90USB instead. Also put #ifndef AT90USB around the HardwareSerial_h trick, so now Printrboard / Brainwave support compiles on Arduino 1.0.2 as well.
12 years ago
4d351b4846
Improved formatting and comments for consistency.
12 years ago
a30007caa4
If fastio.h is not messed up then Teensylu and Printrboard are actually using the same pins.
12 years ago
b1c38d4c82
Avoid compiler warnings (redefined MOTHERBOARD) in Arduino 1.0 and greater.
12 years ago
42e21bb06e
Add support for Printrboard (from https://github.com/lincomatic/Marlin ) and Brainwave (from https://github.com/metrix/Sprinter ).
12 years ago
57429cb9fe
Fix for keypad
12 years ago
f934d0ef5b
Merge remote-tracking branch 'tonokip/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
12 years ago
ffc69537aa
Update on some comments, make the MOTHERBOARD list complete again.
12 years ago
0f73afb0b0
Avoid defining overriding definitions for the RepRapDiscount Smart
...
Controller. Remove common definitions. Harmonize declaration order.
12 years ago
36b452c7ac
Remove abbrs.
12 years ago
3cbaad9288
RepRapDiscount Smart Controller pin definitions.
12 years ago
f5631a89e8
Add dummy Emergancy Pin to Gen7 1.4
...
Change required after pulling from ErikZalm.
12 years ago
a4f9e1ebf2
Merge git://github.com/ErikZalm/Marlin into Marlin_v1
12 years ago
2873d67b17
Put bogus temp override back in Gen7 up to 1.3
...
Took out the ifdef when I split 1.4 out and forgot to permanently
define it for <=1.3.
12 years ago
d07b6e93d5
Add support for Megatronics
12 years ago
8016f058bc
fix max endstop pins
12 years ago
abf0693e8e
Added KILL_PIN -1 to gen7 boards
12 years ago
d728e35658
Update Marlin/pins.h
12 years ago
1c1fddc7ac
Added support for the Rambo reprap electronics board. Added Mcodes to set
...
motor current and microstepping pins.
12 years ago
47d4f55bc0
Fix Gen7 1.4 pinout
...
Gen7 1.4 uses very different pin assignments, might as well make a new
section and remove some of the conditionals from each. It's easier to change
your pin assingment this way if like me you don't wire it exactly to plan.
12 years ago
50cde90324
Added support for dual Z axis stepper drivers
12 years ago
538189cc19
Fixed soft limits when the origin is in the middle.
...
HOME_POS is now always where the endstop is and can be outside the limits.
The limits are now defined by MIN_POS and MAX_POS rather than HOME_POS and MAX_LENGTH.
The Z is axis now homed first if direction is away from the bed.
Saguinololu limit pins change from MIN to MAX according to the homing direction.
13 years ago
e9bec9b6fe
Fixed E1_ENABLE pin for Ultimaker. This was wrong for the 1.5.4 and 1.5.3 PCB (I cannot check the 1.5.6)
13 years ago
602c8ee02b
Melzi support
13 years ago
464b755918
added support for the UltiController
13 years ago
5550e893d5
New board variant, Open Motion Controller
...
Open Hardware board currently used by the group build of http://tvrrug.org.uk
The board can be found at http://solderpad.com/folknology/open-motion-controller/
Signed-off-by: Michel Pollet <buserror@gmail.com>
13 years ago
2e749d60c3
Added DISABLE_MAX_ENDSTOPS
13 years ago
19a47dae4a
Merge pull request #99 from Justblair/master
...
Better pin configuration for rotary encoder in RAMPS boards
13 years ago
c077316b2b
Added PID autotune. (experimental)
...
M303 Starts autotune. Wait till the Kp Ki and Kd constants are printed.
Put these values in Configuration.h
13 years ago
02ee9e3d30
Changed Pin Assignment for the RAMPS motherboard so that LCD and Rotary encoder are all wired to AUX-4
...
This simplifies wiring for those with RAMPS 1.3 and 1.4 boards.
13 years ago
cb0c84e075
Merge remote-tracking branch 'justblair/master' into Marlin_v1
13 years ago
1d5809d458
Merge pull request #88 from daid/Marlin_v1
...
Made plan_buffer_line arguments const...
13 years ago
ed951b1977
Fixed RAMPS 1.2 support (Found and fixed by rrhb)
13 years ago
f278e1c00f
This is in my opinion a much better way of dealing with SD cards than my previous fix.
...
Instead of adding a momentary switch to fake the insertion of the card I have modified the ultralcd menu item:
Card Menu -> Refresh
to reinitialise the card providing that the SDCARDDETECT pin has been set to -1 in the pins.h file. This requires one less switch on the front panel and the refresh menu item is in the most relevent place for a user who wishes to inert a card and then print from it.
It also means that the "Card inserted" messages do not bother the users of these card readers (they dont make sense for users without SCCARDDETECT)
13 years ago
00d33e6b82
Typo fix
13 years ago
7d124478fa
Only protect the heater pins for the defined extruders.
...
Changed the way the extruder pins are defined so it doesn't create extra -1 entries in the list.
13 years ago
1ebe7d1ab6
Merge pull request #83 from phord/tempfix
...
Add explicit #define for bogus temp override
13 years ago
b65ef8d66c
Add support for upcoming Gen7 v1.4
...
V1.4 moves thermistor power to the always-on 5v line.
The BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE is no longer
needed on this board. Add a new motherboard type to
support this feature.
13 years ago
740f0c7690
Add explicit #define for bogus temp override
...
The code to ignore the "bad thermistor reading failsafe"
suicide function depends on the existing of the PS_ON pin
feature. But in some boards this shouldn't be the case
Fix this by adding an explicit definition to make our
intentions more clear and separable.
13 years ago
ba8500a236
pins.h: Define Z_MAX_PIN for Gen7 board
...
The Z_MAX_PIN value was defined as no-value, but this causes
the compile to fail. Fix this by setting the Z_MAX_PIN to the
correct value (which happens to be 0 for pin PB0/DIO0/0).
13 years ago
7b14953c99
Fix build on Sanguino based boards with ATmega1284P
13 years ago
286d5003fa
Fixed compiler warning for Sanguino compile
13 years ago
ce714fe306
Fixes in pins.h
13 years ago
35e57bf149
Added gen6 deluxe.
13 years ago
84ea2d61e8
Moved gen7 boards to motherboard type 10, 11 and 12.
...
Split ramps1.3 in Sprinter like config and multiextruder config.
13 years ago
d298dd121f
merged SBUBA82 and Justblair
13 years ago
a05a261b72
Added a workaround. Ramps SD card does not have sdcarddetect. My temporary solution is to add a momentary swtich
...
that pulls down the SDCARDDETECT pin and mimicking the pull and reinsert ofa a SD card
13 years ago
1b6765ed12
Updated the pin config for RAMPS 1.3 to include ultimaker new style LCD/Rotary Encoder interface
13 years ago
e661578c84
support for GEN7 1.1,1.2 and 1.3
13 years ago
d309565b56
Merge remote-tracking branch 'upstream/Marlin_v1' into Marlin_v1
...
Conflicts:
Marlin/Configuration.h
13 years ago
11518a987f
merged with triffid fork
13 years ago
da040fd393
Fixed ultimaker heater 1 pins. (Thanks daid)
13 years ago
a11f3b2d2f
- Pins for modified GEN7 assigned
...
- Added support for ATMega1284
13 years ago
9f139d6e0e
Added MAX6675 support. (Thanks to gregfrost)
...
Needs some work to remove the blocking in read max6675.
13 years ago
e45e5c68bb
Added support for Gen3+ (Pins file only)
...
Added late z enable. (blddk request)
Only calculate look ahead if >2 moves in buffer.
Removed some FORCE_INLINE to save memory.
Signed-off-by: Erik van der Zalm <erik@vdzalm.eu>
13 years ago
ab01658fd2
local configuration stuff- WATCHPERIOD causes breakage, disable. few other misc changes
13 years ago
71dc82e0b4
my local configuration
13 years ago
cee5f9020a
added suicide pin for a power supply to the arduino that is only active if the arduino is holding high for an output.
13 years ago
415aadf704
lcd panel bed support
...
advance and ultipanel not any more in default config
13 years ago
e017228569
Merged multiple extruder support.
...
Soft PWM. (Sanguinololu can also have PID temperature control)
Interrupt save WRITE for addresses > 0x0FF
13 years ago
4fd75dc813
Working version of multiple extruders (up to 3)
...
- The temperature control is pretty much complete
(not sure what to do w/ autotemp though)
Changed the pins assignment to clearly separate bed and extruder heaters
and temp sensors, changed a bit how termistor tables are handled.
- The steppers control is rudimentary
(only chanages what pins it uses depending on the active_extruder var,
but that's enough for switching extruder in the start.gcode in the
the profiles)
- Tested only w/ RAMPS 1.4
13 years ago
b0c3871750
more fixing of the sanguino math round problem
13 years ago
7b70caab7c
made progmem mainly, found one bug in cardreader, added a empty class for cardreader in case no sd support.
13 years ago
76b3f805c0
Added teensylu pins
13 years ago
1d171e9e52
reformating and some minor bugs/things found on the way.
13 years ago
40e8081623
changed end of line to windows, which seems to be the majority of developers main platform.
13 years ago
d7c4f0780b
Added M42, M80 and M81
13 years ago
094afe7c10
Merged Marlin, Marlin non gen6 and Ultimaker changes
13 years ago
750f6c33e3
first commit
13 years ago
Neil Darlow