0da636e1a3
Set correct stepper direction on reset ( #13032 )
...
On a reset steppers were being initialized to incorrect direction. Original code wasn't respecting `INVERT_Z_DIR` define.
6 years ago
24fffb8d93
Fix undefined lcd_tmpfan_speed on NO_LCD_MENUS ( #13006 )
6 years ago
f4d1f13358
Warn on cold extrusion, dont error
6 years ago
2f35747f29
L6470 SPI daisy chain support ( #12895 )
6 years ago
dc65d96aca
Fix TMC compile error ( #12965 )
6 years ago
0495fcd475
Minor spacing fix
6 years ago
8a3f1d6932
Fix chopper timing struct and initialization ( #12943 )
6 years ago
acf266fe78
Fix a compile warning, etc. ( #12955 )
6 years ago
712e23c383
Fix up some whitespace
6 years ago
e6805582a6
M569 to change stepping mode. Add new TMC section to LCD. ( #12884 )
6 years ago
7fde8d9d1e
Add CreatorPro / Makerbot / QIDI / etc and Mightboard RevE support ( #12855 )
...
- Fix a bug in MAXxxxx thermocouple temp reporting.
- Add support for 3-wire HD44780.
- Add support for PCA9533 RGB driver.
- Add configuration examples for FlashForge CreatorPro.
6 years ago
082f6a27de
ADAPTIVE_FAN_SLOWING extension to hotend thermal protection ( #12853 )
6 years ago
459f4fef60
Fix Temperature::init bug with HEATER_4_PIN
6 years ago
19fea772e5
Use E_AXIS_N where it makes sense
6 years ago
1fd8e2c649
Fix: Junction Deviation calculates wrong cos(theta) on CoreXY ( #12879 )
6 years ago
6a8fb0f25f
Simplify backlash compensation code. ( #12813 )
...
- Use `TEST(dm,axis)` to determine directions instead of doing comparisons.
- Remove recomputation of `millimeters` and `delta_mm` since backlash compensation should not affect the distance over which material is extruded.
6 years ago
81e753064a
Fix ExtUI compile warnings and error ( #12799 )
6 years ago
cb643d87df
Adding missing code for triple Z-stepper auto-align ( #12786 )
6 years ago
60cb36bef3
Misc. improvements ( #12747 )
...
* Make ExtUI respect MAXTEMP limits
- Temperatures are now clamped by MAXTEMP limits rather than arbitrary values.
* Speed up USB init, add status
- Speed up USB initialization
- Show status message if init failed
* Enable status messages for EXTENSIBLE_UI
* Adjust max limit to MAX_TEMP - 15
* Misc. tweaks to formatting, const, etc.
6 years ago
371d9a1acf
Fix line-endings, formatting, whitespace
...
Followup to #12770
6 years ago
135c74017c
Fix compile DEBUG_EEPROM_READWRITE error ( #12746 )
6 years ago
3877bf9704
Fix compile error with delta and sensorless homing ( #12740 )
6 years ago
cfc5e96b4b
Move JD to Config.h (and fix jerk->eeprom bug) ( #12720 )
6 years ago
594898aea7
Limit hotend / bed temperature to maxtemp-15 ( #12713 )
6 years ago
367a9f65aa
Add Formbot 350c Thermistor ( #12661 )
6 years ago
9d59a9c840
Followup to #12691 (typo)
6 years ago
98cf546771
Limit set hotend temperature to maxtemp. ( #12690 )
6 years ago
4dad489a50
[2.0.x] Limit PID autotune target to maxtemp-15 ( #12691 )
6 years ago
8dcc28c9ae
Squelch warning mentioned in #11061 ( #12676 )
6 years ago
c6e09c2689
[2.0.x] G33 clean up ( #12648 )
...
Remove obsolete workarounds in G33 for the now fixed zprobe_zoffset bug
6 years ago
55144284c2
TMC connection test, spreadCycle parameters, improved debugging ( #12616 )
6 years ago
6cf8d40f41
Fix some serial echos of pin states
6 years ago
e8bda62d2a
Followup to servo angles patch
...
Fix #12594
6 years ago
b22716e938
M425 Backlash Correction ( #11061 )
6 years ago
50b2fbd031
Trinamic: Split stealthChop, improve driver monitoring, etc. ( #12582 )
6 years ago
e874f9664c
Tweaks to endstops code
6 years ago
3c58b16c9f
Move stepper enable/disable to stepper_indirection.h ( #12562 )
6 years ago
aaf862aef2
Fix angles for disabled EDITABLE_SERVO_ANGLES ( #12559 )
6 years ago
c986239837
A single SERIAL_ECHO macro type ( #12557 )
6 years ago
8be91677df
Fix Skew factors ( #12555 )
...
- Ensure Skew factors are calculated from test square measurements
6 years ago
03ef2d6c82
Fix "paused" message and M125 called by M25 ( #12551 )
6 years ago
95d154a91f
Fans loop macro
6 years ago
09d6db491a
Fix wait_for_bed compile error
6 years ago
29c53f2402
Hide some compile warnings
6 years ago
caca3c8503
Use wait_for_bed with WAIT_FOR_BED_HEATER
...
Addressing #12517
6 years ago
8a0992d921
Fast PWM for controller fan ( #12485 )
6 years ago
4bcb63b705
Fix for #12482 ( #12483 )
...
Fix Z-move to uninitialized position in SWITCHING_EXTRUDERS tool_change (no_move=true)
6 years ago
90a58488b5
Corrected unused var, default switch, Travis tests ( #12477 )
6 years ago
1f93d2bcf7
Fix LCD compile error, etc. ( #12472 )
6 years ago
c1e17037e5
Various fixes for MarlinUI and ExtUI ( #12439 )
6 years ago
jeffstaley