1367df2875
Replace double with float, optimize calculation
7 years ago
3fd1f32b73
Fix ADC key and chamber temp
7 years ago
3701869e6c
Add HAL_timer_start for AVR, use stepper timer to time pulses
7 years ago
853a9056ac
Long thermistor tables need special consideration
7 years ago
1ce97f1f6d
Faster (bisect) search in thermistor tables ( #10883 )
7 years ago
d557c84a71
[2.0.x] Error for FAST_PWM_FAN with 32 bit CPU ( #10798 )
7 years ago
569df3fc0c
Fix interrupt-based endstop detection
...
- Also implemented real endstop reading on interrupt.
7 years ago
a11eb50a3e
Refactor and optimize Stepper/Planner
...
Better encapsulation and considerably reduce stepper jitter
7 years ago
0566badcef
Add memory barrier, optimal interrupt on-off
...
Disabling an ISR on ARM has 3 instructions of latency. A Memory barrier is REQUIRED to ensure proper and predictable disabling. Memory barriers are expensive, so avoid disabling if already disabled (See https://mcuoneclipse.com/2015/10/16/nvic-disabling-interrupts-on-arm-cortex-m-and-the-need-for-a-memory-barrier-instruction/ )
7 years ago
e1d9046efc
[2.0.x] Temperature reading fix ( #10774 )
7 years ago
99ecdf59af
Smarter MIN, MAX, ABS macros
...
Use macros that explicitly avoid double-evaluation and can be used for any datatype, replacing `min`, `max`, `abs`, `fabs`, `labs`, and `FABS`.
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
083ec9963e
Tweaks to heater / lcd conditions
7 years ago
8f8c6a9bc4
Move get_axis_position_mm to Planner ( #10718 )
7 years ago
a1062eec5b
Better handling of DELAY_NS and DELAY_US ( #10716 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
f5aaa2d6c0
Fix some compiler warnings
7 years ago
625035a9ce
Fix M301 access to lpq_len ( #10714 )
...
Co-Authored-By: Zwaubel
7 years ago
325bbbc8c2
[2.0.x] Enable AD595 and AD8495 in concert ( #10693 )
...
* Allow both AD595 and AD8495 in concert
* General temperature code tweaks
7 years ago
81b632c255
Additional temp-oriented improvements
7 years ago
e911635fb1
Add thermocouple with AD8495 support
7 years ago
5ac226aa93
Further cleanup of inline delays
7 years ago
2242b98248
[LPC176x] Emergency Parser Feature ( #10516 )
7 years ago
9789c1c719
Fix current_temperature_chamber compile error
...
Fix #10505
7 years ago
0c428a66d9
Proper AVR preemptive interrupt handling ( #10496 )
...
Also simplify logic on all ARM-based interrupts. Now, it is REQUIRED to properly configure interrupt priority. USART should have highest priority, followed by Stepper, and then all others.
7 years ago
cb46cb8480
Add HAS_HEATED_BED conditional ( #10495 )
7 years ago
0e8242180d
Chamber temperature monitoring and auto fan control.
...
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
7 years ago
1c36606886
Fix MSG_HEATING_FAILED_LCD_BED macro evaluation
7 years ago
8bc93c6f2b
Improve heating/cooling LCD messages ( #10293 )
7 years ago
7cbbc2af7a
[2.0.x] Optional heater signal inversion ( #10260 )
7 years ago
97e8a6ebd9
Various fixes for DUE... ( #10152 )
...
- Watchdog reset during SD Card initialization.
- Move `DebugMonitor` to `DebugMonitor_Due.cpp`.
- Since the watchdog is enabled on boot do extra resets during init.
- Have `thermalManager` do watchdog reset before its ISR starts to prevent reset.
- Ensure that timers are stopped before reprogramming them to address tone issues.
- Improve SAM3XE reset when reflashed through the native port.
7 years ago
837ac2fdbd
[2.0.x] Fix_Autotune_THERMAL_PROTECTION_BED_off ( #10166 )
...
- Fix Autotune Thermal Protection
- Make 2 constants in autotune configurable
7 years ago
c6ff39cc14
Spacing cleanup
7 years ago
ffbf63e6af
Add HAS_TEMP_SENSOR conditional
7 years ago
649f375494
Fix: M112 calling kill from interrupt ( #9923 )
...
Fix #9906
7 years ago
83d7e95de0
Add MSG_THERMAL_RUNAWAY_BED ( #9691 )
7 years ago
e698998343
More reliable PROBING_HEATERS_OFF with BED_LIMIT_SWITCHING
7 years ago
b5e92f4f90
[2.0.x] Enable / disable PSU automatically ( #9503 )
7 years ago
2bea1bda56
Move more strings to PROGMEM
7 years ago
750cc02b3a
Use delay() in serial temp report
7 years ago
a408209d24
More reliable temperature serial report?
7 years ago
f7efac57b7
Multi-host support
7 years ago
0e93506985
Fix for issue #9005 , #8942 - Bed PID autotuning ( #9036 )
7 years ago
4af3d436b2
M303 pid autotune cleanup, commentary
7 years ago
5e01ee8adf
Temperature updates for parity with 1.1.x
7 years ago
fdc5e72720
A single setting to validate filament width
7 years ago
de5ca96654
More parity with 1.1.x, plus whitespace
7 years ago
0d531d9655
Missing HAS_HEAT_BED conditional
...
Fixes issue found in #8779
7 years ago
cf2193c07f
Comment, fix filament width sensor
7 years ago
4fa65a5c25
TCNT0 => HAL_timer_get_current_count
...
Fix #8710
7 years ago
c1184552ac
Change K1 to required option PID_K1
7 years ago
45c2388a58
Apply const to thermal_runaway_protection args
7 years ago
etagle