e911635fb1
Add thermocouple with AD8495 support
7 years ago
05c33833e7
[2.0.x] Add NO_LCD_MENUS option ( #10582 )
7 years ago
11ab017dd0
Creality3D Power-Loss Recovery
7 years ago
5cc7916e69
Add G29_RETRY_AND_RECOVER feature
...
- Add an option to retry G29, optionally executing a G-code procedure after each failed probe.
7 years ago
2d9b0a66fe
Add Filament Change accelerations
7 years ago
0e8242180d
Chamber temperature monitoring and auto fan control.
...
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
7 years ago
2fa0a73c2c
Implement filament change continuous purge
7 years ago
1d22609473
MIN_PROBE_EDGE replaces DELTA_PROBEABLE_RADIUS
7 years ago
c24dbcbfe1
When STATUS_EXPIRE_SECONDS is 0, hide the position. ( #10081 )
...
Some users may prefer to hide the position updates on the `LIGHTWEIGHT_UI` altogether. This leads to an even less cluttered display (it also saves on SPI traffic and one byte of RAM).
7 years ago
e7a61de8af
[2.0] FWRetract Reset (Best way) ( #10083 )
7 years ago
e7570f3195
Improve TMC config organization, naming
7 years ago
6b4a928145
2uS default step pulse ( #9989 )
7 years ago
94f5204629
Move AUTO_REPORT_SD_STATUS to SDSUPPORT block
7 years ago
b198b49d15
Followup to AUTO_REPORT_SD_STATUS
...
Followup to #9832
7 years ago
23a576faf7
[2.0] Fix for FW retract ( #9878 )
7 years ago
b8485528b2
Prettify LCD_PROGRESS_BAR options
7 years ago
e65a853c59
Fix LCD_PROGRESS_BAR
...
Fix #9208
7 years ago
2bd252b501
[2.0.x] LIN_ADVANCE v1.5 ( #9712 )
7 years ago
532bb3aaa1
Lightweight status screen for ST7920
...
- This status screen uses the ST7920 character generator to greatly
reduce SPI traffic and MCU load when updating the status screen.
- Has been tested with the RepRapDiscount Full Graphics Smart Controller
but should work with any LCD that uses an ST7920 or fully compatible
controller.
7 years ago
59c98d6fd5
Hephestos2 heated bed kit for all ( #9757 )
7 years ago
9019ea0fce
Option to force X or Y to home first when homing the other axis
7 years ago
330437ad7c
Update LCD_SET_PROGRESS_MANUALLY in configs
7 years ago
349dafa728
config update (set to -1)
7 years ago
5b70d3da1c
Update DIGIPOT_I2C_MOTOR_CURRENTS comments
7 years ago
694d2ebec0
TMC SW SPI pins in Configuration_adv.h
...
Counterpart to #9632
7 years ago
1541224a81
Enable Z axis and delta sensorless homing ( #9516 )
7 years ago
b2f8b4ada5
I2C position encoders update ( #9533 )
...
Updating I2C position encoders to enable babystepping and Babystep XY when using the ecm microstep correction method. Also changed default method to ECM microstep.
7 years ago
374f2a5e16
[2.0.x] Fixed wrong information about TMC2208 wiring ( #9335 )
7 years ago
5c69d45f5b
[2.0.x] TMC2130 support for LPC platform ( #9114 )
7 years ago
8190fdb260
[2.0.x] Option to use Neopixel as case light ( #9270 )
...
* Add option to use Neopixel as case light
* Apply CASE_LIGHT_USE_NEOPIXEL to example configs
7 years ago
02ff12d491
More up front option to show SD percentage
7 years ago
5c076a6d93
Improved M915 description
7 years ago
cdc61ebf53
Add M915 configuration option
7 years ago
7541316bb4
Add M701/M702 Filament Load/Unload, M603
7 years ago
2929c9e56f
A specific option to SLIM_LCD_MENUS
7 years ago
f704f405af
Add pause/resume actions on M600, M125
7 years ago
f0a8a1a853
[2.0.x] Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE ( #8866 )
...
* Use NOZZLE_PARK_FEATURE for ADVANCED_PAUSE_FEATURE
7 years ago
fdc5e72720
A single setting to validate filament width
7 years ago
933f76fda3
Option to disable all volumetric extrusion
7 years ago
5595098063
V2 Extended NanoDLP_Z_Move_Sync to G4 & G28,Added all axis option.
7 years ago
0cd1e91056
[2.0.x] TMC driver update ( #8769 )
7 years ago
ae663a4198
PROBE_DOUBLE_TOUCH => MULTIPLE_PROBING
7 years ago
8f90642eea
LED_CONTROL_MENU config changes
7 years ago
cf0f78336b
New Feature: LED_CONTROL_MENU
7 years ago
a67cf78c6b
Clean up whitespace, spacing
7 years ago
7be4857ab9
Tweak BLOCK_BUFFER_SIZE description
7 years ago
5926c9c97b
Followup for MESH_EDIT_GFX_OVERLAY
7 years ago
dc82babe8e
Implement NANODLP_Z_SYNC for 2.0.x
7 years ago
54774841ba
Merge pull request #8416 from thinkyhead/bf2_M114_DETAIL
...
[2.0] Add M114_DETAIL to Configuration_adv.h
7 years ago
009e3a7aa7
Add M114_DETAIL to Configuration_adv.h
7 years ago
nightdemonx