Estimate Remaining Time (graphical display) (#15497)

Marlin/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

Marlin/src/gcode/lcd/M73.cpp

@@ -39,7 +39,10 @@
  */
 void GcodeSuite::M73() {
   if (parser.seen('P'))
-    ui.set_progress(parser.value_byte());
+    ui.set_progress((PROGRESS_SCALE) > 1
+      ? parser.value_float() * (PROGRESS_SCALE)
+      : parser.value_byte()
+    );
 }
 
 #endif // LCD_SET_PROGRESS_MANUALLY

Marlin/src/inc/Conditionals_LCD.h

@@ -530,6 +530,7 @@
 #define HAS_COLOR_LEDS               ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED)
 #define HAS_LEDS_OFF_FLAG            (BOTH(PRINTER_EVENT_LEDS, SDSUPPORT) && HAS_RESUME_CONTINUE)
 #define HAS_PRINT_PROGRESS           EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY)
+#define HAS_PRINT_PROGRESS_PERMYRIAD (HAS_PRINT_PROGRESS && EITHER(PRINT_PROGRESS_SHOW_DECIMALS, SHOW_REMAINING_TIME))
 #define HAS_SERVICE_INTERVALS        (ENABLED(PRINTCOUNTER) && (SERVICE_INTERVAL_1 > 0 || SERVICE_INTERVAL_2 > 0 || SERVICE_INTERVAL_3 > 0))
 #define HAS_FILAMENT_SENSOR          ENABLED(FILAMENT_RUNOUT_SENSOR)
 

Marlin/src/inc/SanityCheck.h

@@ -2511,3 +2511,11 @@ static_assert(   _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2)
   #endif
   #undef _PIN_CONFLICT
 #endif
+
+#if !HAS_GRAPHICAL_LCD
+  #if ENABLED(PRINT_PROGRESS_SHOW_DECIMALS)
+    #error "PRINT_PROGRESS_SHOW_DECIMALS currently requires a Graphical LCD."
+  #elif ENABLED(SHOW_REMAINING_TIME)
+    #error "SHOW_REMAINING_TIME currently requires a Graphical LCD."
+  #endif
+#endif

Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp

@@ -566,7 +566,7 @@ FORCE_INLINE void _draw_bed_status(const bool blink) {
 #if HAS_PRINT_PROGRESS
 
   FORCE_INLINE void _draw_print_progress() {
-    const uint8_t progress = ui.get_progress();
+    const uint8_t progress = ui.get_progress_percent();
     lcd_put_u8str_P(PSTR(
       #if ENABLED(SDSUPPORT)
         "SD"
@@ -613,7 +613,7 @@ void MarlinUI::draw_status_message(const bool blink) {
     // Draw the progress bar if the message has shown long enough
     // or if there is no message set.
     if (ELAPSED(millis(), progress_bar_ms + PROGRESS_BAR_MSG_TIME) || !has_status()) {
-      const uint8_t progress = get_progress();
+      const uint8_t progress = get_progress_percent();
       if (progress > 2) return draw_progress_bar(progress);
     }
 

Marlin/src/lcd/dogm/status_screen_DOGM.cpp

@@ -99,6 +99,9 @@
 
 #define STATUS_HEATERS_BOT (STATUS_HEATERS_Y + STATUS_HEATERS_HEIGHT - 1)
 
+#define PROGRESS_BAR_X 54
+#define PROGRESS_BAR_WIDTH (LCD_PIXEL_WIDTH - PROGRESS_BAR_X)
+
 #if ENABLED(MARLIN_DEV_MODE)
   #define SHOW_ON_STATE READ(X_MIN_PIN)
 #else
@@ -330,6 +333,26 @@ void MarlinUI::draw_status_screen() {
     static char wstring[5], mstring[4];
   #endif
 
+  #if HAS_PRINT_PROGRESS
+    #if DISABLED(DOGM_SD_PERCENT)
+      #define _SD_DURATION_X(len) (PROGRESS_BAR_X + (PROGRESS_BAR_WIDTH) / 2 - (len) * (MENU_FONT_WIDTH) / 2)
+    #else
+      #define _SD_DURATION_X(len) (LCD_PIXEL_WIDTH - (len) * (MENU_FONT_WIDTH))
+    #endif
+
+    static uint8_t progress_bar_solid_width = 0, lastProgress = 0;
+    #if ENABLED(DOGM_SD_PERCENT)
+      static char progress_string[5];
+    #endif
+    static uint8_t lastElapsed = 0, elapsed_x_pos = 0;
+    static char elapsed_string[10];
+    #if ENABLED(SHOW_REMAINING_TIME)
+      #define SHOW_REMAINING_TIME_PREFIX 'E'
+      static uint8_t estimation_x_pos = 0;
+      static char estimation_string[10];
+    #endif
+  #endif
+
   // At the first page, generate new display values
   if (first_page) {
     #if ANIM_HBC
@@ -353,6 +376,50 @@ void MarlinUI::draw_status_screen() {
       strcpy(wstring, ftostr12ns(filwidth.measured_mm));
       strcpy(mstring, i16tostr3(planner.volumetric_percent(parser.volumetric_enabled)));
     #endif
+
+    // Progress / elapsed / estimation updates and string formatting to avoid float math on each LCD draw
+    #if HAS_PRINT_PROGRESS
+      const progress_t progress =
+        #if HAS_PRINT_PROGRESS_PERMYRIAD
+          get_progress_permyriad()
+        #else
+          get_progress_percent()
+        #endif
+      ;
+      duration_t elapsed = print_job_timer.duration();
+      const uint8_t p = progress & 0xFF, ev = elapsed.value & 0xFF;
+      if (progress > 1 && p != lastProgress) {
+        lastProgress = p;
+
+        progress_bar_solid_width = uint8_t((PROGRESS_BAR_WIDTH - 2) * progress / (PROGRESS_SCALE) * 0.01f);
+
+        #if ENABLED(DOGM_SD_PERCENT)
+          strcpy(progress_string, (
+            #if ENABLED(PRINT_PROGRESS_SHOW_DECIMALS)
+              permyriadtostr4(progress)
+            #else
+              ui8tostr3(progress / (PROGRESS_SCALE))
+            #endif
+          ));
+        #endif
+      }
+
+      if (ev != lastElapsed) {
+        lastElapsed = ev;
+        const bool has_days = (elapsed.value >= 60*60*24L);
+        const uint8_t len = elapsed.toDigital(elapsed_string, has_days);
+        elapsed_x_pos = _SD_DURATION_X(len);
+
+        #if ENABLED(SHOW_REMAINING_TIME)
+          if (!(ev & 0x3)) {
+            duration_t estimation = elapsed.value * (100 * (PROGRESS_SCALE) - progress) / progress;
+            const bool has_days = (estimation.value >= 60*60*24L);
+            const uint8_t len = estimation.toDigital(estimation_string, has_days);
+            estimation_x_pos = _SD_DURATION_X(len + 1);
+          }
+        #endif
+      }
+    #endif
   }
 
   const bool blink = get_blink();
@@ -485,55 +552,44 @@ void MarlinUI::draw_status_screen() {
     //
     // Progress bar frame
     //
-    #define PROGRESS_BAR_X 54
-    #define PROGRESS_BAR_WIDTH (LCD_PIXEL_WIDTH - PROGRESS_BAR_X)
 
     if (PAGE_CONTAINS(49, 52))
       u8g.drawFrame(PROGRESS_BAR_X, 49, PROGRESS_BAR_WIDTH, 4);
 
-    const uint8_t progress = get_progress();
-
-    if (progress > 1) {
-
     //
     // Progress bar solid part
     //
 
     if (PAGE_CONTAINS(50, 51))     // 50-51 (or just 50)
-        u8g.drawBox(
+      u8g.drawBox(PROGRESS_BAR_X + 1, 50, progress_bar_solid_width, 2);
-          PROGRESS_BAR_X + 1, 50,
-          (uint16_t)((PROGRESS_BAR_WIDTH - 2) * progress * 0.01), 2
-        );
 
     //
     // SD Percent Complete
     //
 
     #if ENABLED(DOGM_SD_PERCENT)
+      if (progress_string[0] != '\0')
         if (PAGE_CONTAINS(41, 48)) {
           // Percent complete
-          lcd_put_u8str(55, 48, ui8tostr3(progress));
+          lcd_put_u8str(55, 48, progress_string);
           lcd_put_wchar('%');
         }
     #endif
-    }
 
     //
     // Elapsed Time
     //
 
-    #if DISABLED(DOGM_SD_PERCENT)
-      #define SD_DURATION_X (PROGRESS_BAR_X + (PROGRESS_BAR_WIDTH / 2) - len * (MENU_FONT_WIDTH / 2))
-    #else
-      #define SD_DURATION_X (LCD_PIXEL_WIDTH - len * MENU_FONT_WIDTH)
-    #endif
-
     if (PAGE_CONTAINS(EXTRAS_BASELINE - INFO_FONT_ASCENT, EXTRAS_BASELINE - 1)) {
-      char buffer[13];
+
-      duration_t elapsed = print_job_timer.duration();
+      #if ENABLED(SHOW_REMAINING_TIME)
-      bool has_days = (elapsed.value >= 60*60*24L);
+        if (blink && (estimation_string[0] != '\0')) {
-      uint8_t len = elapsed.toDigital(buffer, has_days);
+          lcd_put_wchar(estimation_x_pos, EXTRAS_BASELINE, SHOW_REMAINING_TIME_PREFIX);
-      lcd_put_u8str(SD_DURATION_X, EXTRAS_BASELINE, buffer);
+          lcd_put_u8str(estimation_string);
+        }
+        else
+      #endif
+          lcd_put_u8str(elapsed_x_pos, EXTRAS_BASELINE, elapsed_string);
     }
 
   #endif // HAS_PRINT_PROGRESS

Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp

@@ -850,7 +850,7 @@ void ST7920_Lite_Status_Screen::update_progress(const bool forceUpdate) {
     // when an update is actually necessary.
 
     static uint8_t last_progress = 0;
-    const uint8_t progress = ui.get_progress();
+    const uint8_t progress = ui.get_progress_percent();
     if (forceUpdate || last_progress != progress) {
       last_progress = progress;
       draw_progress_bar(progress);

Marlin/src/lcd/extensible_ui/ui_api.cpp

@@ -796,7 +796,7 @@ namespace ExtUI {
   #endif
 
   uint8_t getProgress_percent() {
-    return ui.get_progress();
+    return ui.get_progress_percent();
   }
 
   uint32_t getProgress_seconds_elapsed() {

Marlin/src/lcd/menu/menu.h

@@ -45,7 +45,7 @@ bool printer_busy();
   struct MenuEditItemInfo_##NAME { \
     typedef TYPE type_t; \
     static constexpr float scale = SCALE; \
-    static inline char* strfunc(const float value) { return STRFUNC((TYPE) value); } \
+    static inline const char* strfunc(const float value) { return STRFUNC((TYPE) value); } \
   };
 
 DECLARE_MENU_EDIT_TYPE(uint8_t,  percent,     ui8tostr4pct, 100.0/255);   // 100%       right-justified
@@ -204,7 +204,7 @@ class MenuEditItemBase {
     static screenFunc_t callbackFunc;
     static bool liveEdit;
   protected:
-    typedef char* (*strfunc_t)(const int32_t);
+    typedef const char* (*strfunc_t)(const int32_t);
     typedef void (*loadfunc_t)(void *, const int32_t);
     static void init(PGM_P const el, void * const ev, const int32_t minv, const int32_t maxv, const uint16_t ep, const screenFunc_t cs, const screenFunc_t cb, const bool le);
     static void edit(strfunc_t, loadfunc_t);
@@ -217,7 +217,7 @@ class TMenuEditItem : MenuEditItemBase {
     static inline float unscale(const float value)    { return value * (1.0f / NAME::scale);  }
     static inline float scale(const float value)      { return value * NAME::scale;           }
     static void load(void *ptr, const int32_t value)  { *((type_t*)ptr) = unscale(value);     }
-    static char* to_string(const int32_t value)       { return NAME::strfunc(unscale(value)); }
+    static const char* to_string(const int32_t value) { return NAME::strfunc(unscale(value)); }
   public:
     static void action(
       PGM_P const pstr,                     // Edit label

Marlin/src/lcd/ultralcd.cpp

@@ -58,7 +58,7 @@
 #endif
 
 #if ENABLED(LCD_SET_PROGRESS_MANUALLY)
-  uint8_t MarlinUI::progress_override; // = 0
+  MarlinUI::progress_t MarlinUI::progress_override; // = 0
 #endif
 
 #if HAS_BUZZER
@@ -515,7 +515,7 @@ void MarlinUI::status_screen() {
       if (expire_status_ms > 0) {
 
         // Expire the message if a job is active and the bar has ticks
-        if (get_progress() > 2 && !print_job_timer.isPaused()) {
+        if (get_progress_percent() > 2 && !print_job_timer.isPaused()) {
           if (ELAPSED(ms, expire_status_ms)) {
             status_message[0] = '\0';
             expire_status_ms = 0;
@@ -1534,18 +1534,24 @@ void MarlinUI::update() {
   }
 
   #if HAS_PRINT_PROGRESS
-    uint8_t MarlinUI::get_progress() {
+
+    MarlinUI::progress_t MarlinUI::_get_progress() {
       #if ENABLED(LCD_SET_PROGRESS_MANUALLY)
-        const uint8_t p = progress_override & 0x7F;
+        const progress_t p = progress_override & PROGRESS_MASK;
       #else
-        constexpr uint8_t p = 0;
+        constexpr progress_t p = 0;
       #endif
       return (p
         #if ENABLED(SDSUPPORT)
+          #if HAS_PRINT_PROGRESS_PERMYRIAD
+            ?: card.permyriadDone()
+          #else
             ?: card.percentDone()
           #endif
+        #endif
       );
     }
+
   #endif
 
 #endif // HAS_DISPLAY

Marlin/src/lcd/ultralcd.h

@@ -288,15 +288,28 @@ public:
     static void resume_print();
 
     #if HAS_PRINT_PROGRESS
+      #if HAS_PRINT_PROGRESS_PERMYRIAD
+        typedef uint16_t progress_t;
+        #define PROGRESS_SCALE 100U
+        #define PROGRESS_MASK 0x7FFF
+      #else
+        typedef uint8_t progress_t;
+        #define PROGRESS_SCALE 1U
+        #define PROGRESS_MASK 0x7F
+      #endif
       #if ENABLED(LCD_SET_PROGRESS_MANUALLY)
-        static uint8_t progress_override;
+        static progress_t progress_override;
-        static void set_progress(const uint8_t progress) { progress_override = _MIN(progress, 100); }
+        static void set_progress(const progress_t p) { progress_override = _MIN(p, 100U * (PROGRESS_SCALE)); }
-        static void set_progress_done() { set_progress(0x80 + 100); }
+        static void set_progress_done() { progress_override = (PROGRESS_MASK + 1U) + 100U * (PROGRESS_SCALE); }
-        static void progress_reset() { if (progress_override & 0x80) set_progress(0); }
+        static void progress_reset() { if (progress_override & (PROGRESS_MASK + 1U)) set_progress(0); }
+      #endif
+      static progress_t _get_progress();
+      #if HAS_PRINT_PROGRESS_PERMYRIAD
+        static uint16_t get_progress_permyriad() { return _get_progress(); }
       #endif
-      static uint8_t get_progress();
+      static uint8_t get_progress_percent() { return uint8_t(_get_progress() / (PROGRESS_SCALE)); }
     #else
-      static constexpr uint8_t get_progress() { return 0; }
+      static constexpr uint8_t get_progress_percent() { return 0; }
     #endif
 
     #if HAS_SPI_LCD

Marlin/src/libs/numtostr.cpp

@@ -33,7 +33,7 @@ char conv[8] = { 0 };
 #define MINUSOR(n, alt) (n >= 0 ? (alt) : (n = -n, '-'))
 
 // Convert a full-range unsigned 8bit int to a percentage
-char* ui8tostr4pct(const uint8_t i) {
+const char* ui8tostr4pct(const uint8_t i) {
   const uint8_t n = ui8_to_percent(i);
   conv[3] = RJDIGIT(n, 100);
   conv[4] = RJDIGIT(n, 10);
@@ -43,7 +43,7 @@ char* ui8tostr4pct(const uint8_t i) {
 }
 
 // Convert unsigned 8bit int to string 123 format
-char* ui8tostr3(const uint8_t i) {
+const char* ui8tostr3(const uint8_t i) {
   conv[4] = RJDIGIT(i, 100);
   conv[5] = RJDIGIT(i, 10);
   conv[6] = DIGIMOD(i, 1);
@@ -51,7 +51,7 @@ char* ui8tostr3(const uint8_t i) {
 }
 
 // Convert signed 8bit int to rj string with 123 or -12 format
-char* i8tostr3(const int8_t x) {
+const char* i8tostr3(const int8_t x) {
   int xx = x;
   conv[4] = MINUSOR(xx, RJDIGIT(xx, 100));
   conv[5] = RJDIGIT(xx, 10);
@@ -59,8 +59,36 @@ char* i8tostr3(const int8_t x) {
   return &conv[4];
 }
 
+#if HAS_PRINT_PROGRESS_PERMYRIAD
+  // Convert unsigned 16-bit permyriad to percent with 100 / 23 / 23.4 / 3.45 format
+  const char* permyriadtostr4(const uint16_t xx) {
+    if (xx >= 10000)
+      return "100";
+    else if (xx >= 1000) {
+      conv[3] = DIGIMOD(xx, 1000);
+      conv[4] = DIGIMOD(xx, 100);
+      conv[5] = '.';
+      conv[6] = DIGIMOD(xx, 10);
+      return &conv[3];
+    }
+    else if (xx % 100 == 0) {
+      conv[4] = ' ';
+      conv[5] = RJDIGIT(xx, 1000);
+      conv[6] = DIGIMOD(xx, 100);
+      return &conv[4];
+    }
+    else {
+      conv[3] = DIGIMOD(xx, 100);
+      conv[4] = '.';
+      conv[5] = DIGIMOD(xx, 10);
+      conv[6] = RJDIGIT(xx, 1);
+      return &conv[3];
+    }
+  }
+#endif
+
 // Convert unsigned 16bit int to string 12345 format
-char* ui16tostr5(const uint16_t xx) {
+const char* ui16tostr5(const uint16_t xx) {
   conv[2] = RJDIGIT(xx, 10000);
   conv[3] = RJDIGIT(xx, 1000);
   conv[4] = RJDIGIT(xx, 100);
@@ -70,7 +98,7 @@ char* ui16tostr5(const uint16_t xx) {
 }
 
 // Convert unsigned 16bit int to string 1234 format
-char* ui16tostr4(const uint16_t xx) {
+const char* ui16tostr4(const uint16_t xx) {
   conv[3] = RJDIGIT(xx, 1000);
   conv[4] = RJDIGIT(xx, 100);
   conv[5] = RJDIGIT(xx, 10);
@@ -79,7 +107,7 @@ char* ui16tostr4(const uint16_t xx) {
 }
 
 // Convert unsigned 16bit int to string 123 format
-char* ui16tostr3(const uint16_t xx) {
+const char* ui16tostr3(const uint16_t xx) {
   conv[4] = RJDIGIT(xx, 100);
   conv[5] = RJDIGIT(xx, 10);
   conv[6] = DIGIMOD(xx, 1);
@@ -87,7 +115,7 @@ char* ui16tostr3(const uint16_t xx) {
 }
 
 // Convert signed 16bit int to rj string with 123 or -12 format
-char* i16tostr3(const int16_t x) {
+const char* i16tostr3(const int16_t x) {
   int xx = x;
   conv[4] = MINUSOR(xx, RJDIGIT(xx, 100));
   conv[5] = RJDIGIT(xx, 10);
@@ -96,7 +124,7 @@ char* i16tostr3(const int16_t x) {
 }
 
 // Convert unsigned 16bit int to lj string with 123 format
-char* i16tostr3left(const int16_t i) {
+const char* i16tostr3left(const int16_t i) {
   char *str = &conv[6];
   *str = DIGIMOD(i, 1);
   if (i >= 10) {
@@ -108,7 +136,7 @@ char* i16tostr3left(const int16_t i) {
 }
 
 // Convert signed 16bit int to rj string with 1234, _123, -123, _-12, or __-1 format
-char* i16tostr4sign(const int16_t i) {
+const char* i16tostr4sign(const int16_t i) {
   const bool neg = i < 0;
   const int ii = neg ? -i : i;
   if (i >= 1000) {
@@ -137,7 +165,7 @@ char* i16tostr4sign(const int16_t i) {
 }
 
 // Convert unsigned float to string with 1.23 format
-char* ftostr12ns(const float &f) {
+const char* ftostr12ns(const float &f) {
   const long i = ((f < 0 ? -f : f) * 1000 + 5) / 10;
   conv[3] = DIGIMOD(i, 100);
   conv[4] = '.';
@@ -147,7 +175,7 @@ char* ftostr12ns(const float &f) {
 }
 
 // Convert signed float to fixed-length string with 12.34 / -2.34 format or 123.45 / -23.45 format
-char* ftostr42_52(const float &f) {
+const char* ftostr42_52(const float &f) {
   if (f <= -10 || f >= 100) return ftostr52(f); // need more digits
   long i = (f * 1000 + (f < 0 ? -5: 5)) / 10;
   conv[2] = (f >= 0 && f < 10) ? ' ' : MINUSOR(i, DIGIMOD(i, 1000));
@@ -159,7 +187,7 @@ char* ftostr42_52(const float &f) {
 }
 
 // Convert signed float to fixed-length string with 023.45 / -23.45 format
-char* ftostr52(const float &f) {
+const char* ftostr52(const float &f) {
   long i = (f * 1000 + (f < 0 ? -5: 5)) / 10;
   conv[1] = MINUSOR(i, DIGIMOD(i, 10000));
   conv[2] = DIGIMOD(i, 1000);
@@ -188,7 +216,7 @@ char* ftostr52(const float &f) {
 #endif
 
 // Convert float to fixed-length string with +123.4 / -123.4 format
-char* ftostr41sign(const float &f) {
+const char* ftostr41sign(const float &f) {
   int i = (f * 100 + (f < 0 ? -5: 5)) / 10;
   conv[1] = MINUSOR(i, '+');
   conv[2] = DIGIMOD(i, 1000);
@@ -200,7 +228,7 @@ char* ftostr41sign(const float &f) {
 }
 
 // Convert signed float to string (6 digit) with -1.234 / _0.000 / +1.234 format
-char* ftostr43sign(const float &f, char plus/*=' '*/) {
+const char* ftostr43sign(const float &f, char plus/*=' '*/) {
   long i = (f * 10000 + (f < 0 ? -5: 5)) / 10;
   conv[1] = i ? MINUSOR(i, plus) : ' ';
   conv[2] = DIGIMOD(i, 1000);
@@ -212,7 +240,7 @@ char* ftostr43sign(const float &f, char plus/*=' '*/) {
 }
 
 // Convert signed float to string (5 digit) with -1.2345 / _0.0000 / +1.2345 format
-char* ftostr54sign(const float &f, char plus/*=' '*/) {
+const char* ftostr54sign(const float &f, char plus/*=' '*/) {
   long i = (f * 100000 + (f < 0 ? -5: 5)) / 10;
   conv[0] = i ? MINUSOR(i, plus) : ' ';
   conv[1] = DIGIMOD(i, 10000);
@@ -225,13 +253,13 @@ char* ftostr54sign(const float &f, char plus/*=' '*/) {
 }
 
 // Convert unsigned float to rj string with 12345 format
-char* ftostr5rj(const float &f) {
+const char* ftostr5rj(const float &f) {
   const long i = ((f < 0 ? -f : f) * 10 + 5) / 10;
   return ui16tostr5(i);
 }
 
 // Convert signed float to string with +1234.5 format
-char* ftostr51sign(const float &f) {
+const char* ftostr51sign(const float &f) {
   long i = (f * 100 + (f < 0 ? -5: 5)) / 10;
   conv[0] = MINUSOR(i, '+');
   conv[1] = DIGIMOD(i, 10000);
@@ -244,7 +272,7 @@ char* ftostr51sign(const float &f) {
 }
 
 // Convert signed float to string with +123.45 format
-char* ftostr52sign(const float &f) {
+const char* ftostr52sign(const float &f) {
   long i = (f * 1000 + (f < 0 ? -5: 5)) / 10;
   conv[0] = MINUSOR(i, '+');
   conv[1] = DIGIMOD(i, 10000);
@@ -257,7 +285,7 @@ char* ftostr52sign(const float &f) {
 }
 
 // Convert unsigned float to string with 1234.5 format omitting trailing zeros
-char* ftostr51rj(const float &f) {
+const char* ftostr51rj(const float &f) {
   const long i = ((f < 0 ? -f : f) * 100 + 5) / 10;
   conv[0] = ' ';
   conv[1] = RJDIGIT(i, 10000);
@@ -270,7 +298,7 @@ char* ftostr51rj(const float &f) {
 }
 
 // Convert signed float to space-padded string with -_23.4_ format
-char* ftostr52sp(const float &f) {
+const char* ftostr52sp(const float &f) {
   long i = (f * 1000 + (f < 0 ? -5: 5)) / 10;
   uint8_t dig;
   conv[0] = MINUSOR(i, ' ');

Marlin/src/libs/numtostr.h

@@ -24,69 +24,74 @@
 #include <stdint.h>
 
 // Convert a full-range unsigned 8bit int to a percentage
-char* ui8tostr4pct(const uint8_t i);
+const char* ui8tostr4pct(const uint8_t i);
 
 // Convert uint8_t to string with 123 format
-char* ui8tostr3(const uint8_t i);
+const char* ui8tostr3(const uint8_t i);
 
 // Convert int8_t to string with 123 format
-char* i8tostr3(const int8_t x);
+const char* i8tostr3(const int8_t x);
+
+#if HAS_PRINT_PROGRESS_PERMYRIAD
+  // Convert 16-bit unsigned permyriad value to percent: 100 / 23 / 23.4 / 3.45
+  const char* permyriadtostr4(const uint16_t xx);
+#endif
 
 // Convert uint16_t to string with 12345 format
-char* ui16tostr5(const uint16_t x);
+const char* ui16tostr5(const uint16_t x);
 
 // Convert uint16_t to string with 1234 format
-char* ui16tostr4(const uint16_t x);
+const char* ui16tostr4(const uint16_t x);
 
 // Convert uint16_t to string with 123 format
-char* ui16tostr3(const uint16_t x);
+const char* ui16tostr3(const uint16_t x);
 
 // Convert int16_t to string with 123 format
-char* i16tostr3(const int16_t x);
+const char* i16tostr3(const int16_t x);
 
 // Convert unsigned int to lj string with 123 format
-char* i16tostr3left(const int16_t xx);
+const char* i16tostr3left(const int16_t xx);
 
 // Convert signed int to rj string with _123, -123, _-12, or __-1 format
-char* i16tostr4sign(const int16_t x);
+const char* i16tostr4sign(const int16_t x);
 
 // Convert unsigned float to string with 1.23 format
-char* ftostr12ns(const float &x);
+const char* ftostr12ns(const float &x);
 
 // Convert signed float to fixed-length string with 12.34 / -2.34 or 023.45 / -23.45 format
-char* ftostr42_52(const float &x);
+const char* ftostr42_52(const float &x);
 
 // Convert signed float to fixed-length string with 023.45 / -23.45 format
-char* ftostr52(const float &x);
+const char* ftostr52(const float &x);
 
 // Convert float to fixed-length string with +123.4 / -123.4 format
-char* ftostr41sign(const float &x);
+const char* ftostr41sign(const float &x);
 
 // Convert signed float to string (6 digit) with -1.234 / _0.000 / +1.234 format
-char* ftostr43sign(const float &x, char plus=' ');
+const char* ftostr43sign(const float &x, char plus=' ');
 
 // Convert signed float to string (5 digit) with -1.2345 / _0.0000 / +1.2345 format
-char* ftostr54sign(const float &x, char plus=' ');
+const char* ftostr54sign(const float &x, char plus=' ');
 
 // Convert unsigned float to rj string with 12345 format
-char* ftostr5rj(const float &x);
+const char* ftostr5rj(const float &x);
 
 // Convert signed float to string with +1234.5 format
-char* ftostr51sign(const float &x);
+const char* ftostr51sign(const float &x);
 
 // Convert signed float to space-padded string with -_23.4_ format
-char* ftostr52sp(const float &x);
+const char* ftostr52sp(const float &x);
 
 // Convert signed float to string with +123.45 format
-char* ftostr52sign(const float &x);
+const char* ftostr52sign(const float &x);
 
 // Convert unsigned float to string with 1234.5 format omitting trailing zeros
-char* ftostr51rj(const float &x);
+const char* ftostr51rj(const float &x);
 
 #include "../core/macros.h"
 
 // Convert float to rj string with 123 or -12 format
-FORCE_INLINE char* ftostr3(const float &x) { return i16tostr3(int16_t(x + (x < 0 ? -0.5f : 0.5f))); }
+FORCE_INLINE const char* ftostr3(const float &x) { return i16tostr3(int16_t(x + (x < 0 ? -0.5f : 0.5f))); }
 
 #include "../inc/MarlinConfigPre.h"
 
@@ -95,5 +100,5 @@ FORCE_INLINE char* ftostr3(const float &x) { return i16tostr3(int16_t(x + (x < 0
   char* ftostr4sign(const float &fx);
 #else
   // Convert float to rj string with 1234, _123, -123, __12, _-12, ___1, or __-1 format
-  FORCE_INLINE char* ftostr4sign(const float &x) { return i16tostr4sign(int16_t(x + (x < 0 ? -0.5f : 0.5f))); }
+  FORCE_INLINE const char* ftostr4sign(const float &x) { return i16tostr4sign(int16_t(x + (x < 0 ? -0.5f : 0.5f))); }
 #endif

Marlin/src/sd/cardreader.h

@@ -118,6 +118,9 @@ public:
   static inline void pauseSDPrint() { flag.sdprinting = false; }
   static inline bool isPaused() { return isFileOpen() && !flag.sdprinting; }
   static inline bool isPrinting() { return flag.sdprinting; }
+  #if HAS_PRINT_PROGRESS_PERMYRIAD
+    static inline uint16_t permyriadDone() { return (isFileOpen() && filesize) ? sdpos / ((filesize + 9999) / 10000) : 0; }
+  #endif
   static inline uint8_t percentDone() { return (isFileOpen() && filesize) ? sdpos / ((filesize + 99) / 100) : 0; }
 
   // Helper for open and remove

buildroot/share/tests/megaatmega2560-tests

@@ -63,6 +63,7 @@ opt_enable AUTO_BED_LEVELING_UBL RESTORE_LEVELING_AFTER_G28 DEBUG_LEVELING_FEATU
            SDSUPPORT SDCARD_SORT_ALPHA USB_FLASH_DRIVE_SUPPORT SCROLL_LONG_FILENAMES \
            EEPROM_SETTINGS EEPROM_CHITCHAT GCODE_MACROS CUSTOM_USER_MENUS \
            MULTI_NOZZLE_DUPLICATION CLASSIC_JERK LIN_ADVANCE QUICK_HOME \
+           LCD_SET_PROGRESS_MANUALLY PRINT_PROGRESS_SHOW_DECIMALS SHOW_REMAINING_TIME \
            BABYSTEPPING BABYSTEP_XY NANODLP_Z_SYNC I2C_POSITION_ENCODERS M114_DETAIL
 exec_test $1 $2 "Azteeg X3 Pro with 5 extruders, RRDFGSC, probeless UBL, Linear Advance, and more"
 

config/default/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/ADIMLab/Gantry v1/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/ADIMLab/Gantry v2/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Alfawise/U20-bltouch/Configuration_adv.h

@@ -889,6 +889,11 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Alfawise/U20/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Anet/A2/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Anet/A2plus/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Anet/A6/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Anet/A8/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Anet/A8plus/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Anet/E16/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/ArmEd/Configuration_adv.h

@@ -892,6 +892,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -896,6 +896,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Cartesio/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Creality/CR-10/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Creality/CR-10S/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Creality/CR-10_5S/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Creality/CR-20 Pro/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Creality/CR-20/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Creality/CR-8/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Creality/Ender-2/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Creality/Ender-3/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Creality/Ender-4/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Creality/Ender-5/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Dagoma/Disco Ultimate/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Einstart-S/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/FYSETC/AIO_II/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/FYSETC/Cheetah/base/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/FYSETC/F6_13/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Felix/DUAL/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Felix/Single/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/FlashForge/CreatorPro/Configuration_adv.h

@@ -887,6 +887,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   #define LCD_PROGRESS_BAR                // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Formbot/Raptor/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -892,6 +892,11 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Geeetech/A10/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Geeetech/A10M/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   #define LCD_PROGRESS_BAR                // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Geeetech/A20M/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   #define LCD_PROGRESS_BAR                // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/HMS434/Configuration_adv.h

@@ -856,6 +856,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/JGAurora/A1/Configuration_adv.h

@@ -893,6 +893,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/JGAurora/A5/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/JGAurora/A5S/Configuration_adv.h

@@ -893,6 +893,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/MakerParts/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Malyan/M150/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Malyan/M200/Configuration_adv.h

@@ -890,6 +890,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Mks/Robin/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Mks/Sbase/Configuration_adv.h

@@ -889,6 +889,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/RapideLite/RL200/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/RigidBot/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/SCARA/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Sanguinololu/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Tevo/Michelangelo/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Tevo/Tarantula Pro/Configuration_adv.h

@@ -884,6 +884,11 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 #define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/TheBorg/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/TinyBoy2/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Tronxy/X3A/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Tronxy/X5S-2E/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/UltiMachine/Archim1/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/VORONDesign/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Velleman/K8200/Configuration_adv.h

@@ -901,6 +901,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   #define LCD_PROGRESS_BAR                // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Velleman/K8400/Dual-head/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/Velleman/K8400/Single-head/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)

config/examples/WASP/PowerWASP/Configuration_adv.h

@@ -888,6 +888,11 @@
 // Add an 'M73' G-code to set the current percentage
 //#define LCD_SET_PROGRESS_MANUALLY
 
+#if HAS_PRINT_PROGRESS
+  //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits (Graphical LCD only)
+  //#define SHOW_REMAINING_TIME          // Display estimated time to completion (Graphical LCD only)
+#endif
+
 #if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)