microlab
/
scube
1
1
Fork 0
Code Issues Pull Requests Releases Activity

merging

Browse Source
2.0.x
Erik van der Zalm 13 years ago
parent e017228569 3320a5b37d
commit 84d9cf7339
12 changed files with 358 additions and 203 deletions
Show Stats Download Patch File Download Diff File

32
Marlin/Configuration.h
Unescape Escape View File

@ -20,9 +20,6 @@
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
#define MINIMUM_PLANNER_SPEED 2.0 // (mm/sec)
// If defined the movements slow down when the look ahead buffer is only half full
#define SLOWDOWN
// BASIC SETTINGS: select your board type, thermistor type, axis scaling, and endstop configuration
//// The following define selects which electronics board you have. Please choose the one that matches your setup
@ -65,11 +62,11 @@
#define BED_CHECK_INTERVAL 5000 //ms
//// Experimental watchdog and minimal temp
// The watchdog waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
// If the temperature has not increased at the end of that period, the target temperature is set to zero. It can be reset with another M104/M109
/// CURRENTLY NOT IMPLEMENTED AND UNUSEABLE
//#define WATCHPERIOD 5000 //5 seconds
//// Heating sanity check:
// This waits for the watchperiod in milliseconds whenever an M104 or M109 increases the target temperature
// If the temperature has not increased at the end of that period, the target temperature is set to zero.
// It can be reset with another M104/M109
//#define WATCHPERIOD 20000 //20 seconds
// Actual temperature must be close to target for this long before M109 returns success
#define TEMP_RESIDENCY_TIME 30 // (seconds)
@ -163,6 +160,14 @@
#endif
#endif // PIDTEMP
// extruder run-out prevention.
//if the machine is idle, and the temperature over MINTEMP, every couple of SECONDS some filament is extruded
//#define EXTRUDER_RUNOUT_PREVENT
#define EXTRUDER_RUNOUT_MINTEMP 190
#define EXTRUDER_RUNOUT_SECONDS 30.
#define EXTRUDER_RUNOUT_ESTEPS 14. //mm filament
#define EXTRUDER_RUNOUT_SPEED 1500. //extrusion speed
//===========================================================================
//=============================Mechanical Settings===========================
@ -250,7 +255,12 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#define DEFAULT_XYJERK 20.0 // (mm/sec)
#define DEFAULT_ZJERK 0.4 // (mm/sec)
// If defined the movements slow down when the look ahead buffer is only half full
#define SLOWDOWN
//default stepper release if idle
#define DEFAULT_STEPPER_DEACTIVE_TIME 60
#define DEFAULT_STEPPER_DEACTIVE_COMMAND "M84 X Y E" //z stays powered
//===========================================================================
@ -303,6 +313,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
//#define ULTRA_LCD //general lcd support, also 16x2
//#define SDSUPPORT // Enable SD Card Support in Hardware Console
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift.
#define ULTIPANEL
#ifdef ULTIPANEL
@ -339,6 +350,11 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#define AUTOTEMP_OLDWEIGHT 0.98
#endif
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
//can be software-disabled for whatever purposes by
#define PREVENT_DANGEROUS_EXTRUDE
#define EXTRUDE_MINTEMP 190
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
const int dropsegments=5; //everything with less than this number of steps will be ignored as move and joined with the next movement

2
Marlin/Marlin.h
Unescape Escape View File

@ -4,6 +4,7 @@
// Tonokip RepRap firmware rewrite based off of Hydra-mmm firmware.
// Licence: GPL
#define HardwareSerial_h // trick to disable the standard HWserial
#include <stdio.h>
#include <math.h>
#if ARDUINO >= 100
#include "Arduino.h"
@ -147,6 +148,7 @@ extern float homing_feedrate[];
extern bool axis_relative_modes[];
extern float current_position[NUM_AXIS] ;
extern float add_homeing[3];
extern bool stop_heating_wait;
// Handling multiple extruders pins
extern uint8_t active_extruder;

127
Marlin/Marlin.pde
Unescape Escape View File

@ -27,6 +27,8 @@
#include <math.h>
#include <EEPROM.h>
#include <stdio.h>
#include "EEPROMwrite.h"
#include "fastio.h"
#include "Configuration.h"
@ -39,7 +41,7 @@
#include "motion_control.h"
#include "cardreader.h"
#include "watchdog.h"
#include <stdio.h>
#define VERSION_STRING "1.0.0 Beta 1"
@ -108,6 +110,7 @@
// M206 - set additional homeing offset
// M220 - set speed factor override percentage S:factor in percent
// M301 - Set PID parameters P I and D
// M302 - Allow cold extrudes
// M400 - Finish all moves
// M500 - stores paramters in EEPROM
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
@ -135,7 +138,7 @@ volatile bool feedmultiplychanged=false;
float current_position[NUM_AXIS] = { 0.0, 0.0, 0.0, 0.0 };
float add_homeing[3]={0,0,0};
uint8_t active_extruder = 0;
bool stop_heating_wait=false;
//===========================================================================
//=============================private variables=============================
@ -175,7 +178,8 @@ const int sensitive_pins[] = SENSITIVE_PINS; // Sensitive pin list for M42
//Inactivity shutdown variables
static unsigned long previous_millis_cmd = 0;
static unsigned long max_inactive_time = 0;
static unsigned long stepper_inactive_time = 0;
static unsigned long stepper_inactive_time = DEFAULT_STEPPER_DEACTIVE_TIME*1000;
static unsigned long last_stepperdisabled_time=30*1000; //first release check after 30 seconds
static unsigned long starttime=0;
static unsigned long stoptime=0;
@ -232,7 +236,9 @@ void setup()
SERIAL_PROTOCOLLNPGM("start");
SERIAL_ECHO_START;
SERIAL_ECHOPGM("Free Memory:");
SERIAL_ECHOLN(freeMemory());
SERIAL_ECHO(freeMemory());
SERIAL_ECHOPGM(" PlannerBufferBytes:");
SERIAL_ECHOLN((int)sizeof(block_t)*BLOCK_BUFFER_SIZE);
for(int8_t i = 0; i < BUFSIZE; i++)
{
fromsd[i] = false;
@ -498,19 +504,16 @@ FORCE_INLINE void process_commands()
case 1: // G1
get_coordinates(); // For X Y Z E F
prepare_move();
previous_millis_cmd = millis();
//ClearToSend();
return;
//break;
case 2: // G2 - CW ARC
get_arc_coordinates();
prepare_arc_move(true);
previous_millis_cmd = millis();
return;
case 3: // G3 - CCW ARC
get_arc_coordinates();
prepare_arc_move(false);
previous_millis_cmd = millis();
return;
case 4: // G4 dwell
LCD_MESSAGEPGM("DWELL...");
@ -520,7 +523,7 @@ FORCE_INLINE void process_commands()
st_synchronize();
codenum += millis(); // keep track of when we started waiting
previous_millis_cmd = millis();
while(millis() < codenum ){
manage_heater();
}
@ -540,32 +543,51 @@ FORCE_INLINE void process_commands()
#ifdef QUICK_HOME
if( code_seen(axis_codes[0]) && code_seen(axis_codes[1]) ) //first diagonal move
{
current_position[X_AXIS] = 0; current_position[Y_AXIS] = 0;
current_position[X_AXIS] = 0;current_position[Y_AXIS] = 0;
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
destination[X_AXIS] = 1.5 * X_MAX_LENGTH * X_HOME_DIR;
destination[Y_AXIS] = 1.5 * Y_MAX_LENGTH * Y_HOME_DIR;
feedrate =homing_feedrate[X_AXIS];
destination[X_AXIS] = 1.5 * X_MAX_LENGTH * X_HOME_DIR;destination[Y_AXIS] = 1.5 * Y_MAX_LENGTH * Y_HOME_DIR;
feedrate = homing_feedrate[X_AXIS];
if(homing_feedrate[Y_AXIS]<feedrate)
feedrate =homing_feedrate[Y_AXIS];
prepare_move();
current_position[X_AXIS] = 0; current_position[Y_AXIS] = 0;
current_position[X_AXIS] = (X_HOME_DIR == -1) ? 0 : X_MAX_LENGTH;
current_position[Y_AXIS] = (Y_HOME_DIR == -1) ? 0 : Y_MAX_LENGTH;
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
destination[X_AXIS] = current_position[X_AXIS];
destination[Y_AXIS] = current_position[Y_AXIS];
feedrate = 0.0;
st_synchronize();
plan_set_position(0, 0, current_position[Z_AXIS], current_position[E_AXIS]);
current_position[X_AXIS] = 0;current_position[Y_AXIS] = 0;
endstops_hit_on_purpose();
}
#endif
if((home_all_axis) || (code_seen(axis_codes[X_AXIS])))
{
HOMEAXIS(X);
current_position[0]=code_value()+add_homeing[0];
}
if((home_all_axis) || (code_seen(axis_codes[Y_AXIS]))) {
HOMEAXIS(Y);
current_position[1]=code_value()+add_homeing[1];
}
if((home_all_axis) || (code_seen(axis_codes[Z_AXIS]))) {
HOMEAXIS(Z);
}
if(code_seen(axis_codes[X_AXIS]))
{
current_position[0]=code_value()+add_homeing[0];
}
if(code_seen(axis_codes[Y_AXIS])) {
current_position[1]=code_value()+add_homeing[1];
}
if(code_seen(axis_codes[Z_AXIS])) {
current_position[2]=code_value()+add_homeing[2];
}
#ifdef ENDSTOPS_ONLY_FOR_HOMING
@ -817,6 +839,7 @@ FORCE_INLINE void process_commands()
}
manage_heater();
LCD_STATUS;
if(stop_heating_wait) break;
#ifdef TEMP_RESIDENCY_TIME
/* start/restart the TEMP_RESIDENCY_TIME timer whenever we reach target temp for the first time
or when current temp falls outside the hysteresis after target temp was reached */
@ -830,6 +853,7 @@ FORCE_INLINE void process_commands()
}
LCD_MESSAGEPGM("Heating done.");
starttime=millis();
previous_millis_cmd = millis();
}
break;
case 190: // M190 - Wait for bed heater to reach target.
@ -853,6 +877,7 @@ FORCE_INLINE void process_commands()
manage_heater();
}
LCD_MESSAGEPGM("Bed done.");
previous_millis_cmd = millis();
#endif
break;
@ -896,20 +921,25 @@ FORCE_INLINE void process_commands()
}
else
{
#if ((E_ENABLE_PIN != X_ENABLE_PIN) && (E_ENABLE_PIN != Y_ENABLE_PIN)) // Only enable on boards that have seperate ENABLE_PINS
if(code_seen('E')) {
st_synchronize();
LCD_MESSAGEPGM("Free Move");
bool all_axis = !((code_seen(axis_codes[0])) || (code_seen(axis_codes[1])) || (code_seen(axis_codes[2]))|| (code_seen(axis_codes[3])));
if(all_axis)
{
disable_e0();
disable_e1();
disable_e2();
}
else {
finishAndDisableSteppers();
}
#else
finishAndDisableSteppers();
else
{
st_synchronize();
if(code_seen('X')) disable_x();
if(code_seen('Y')) disable_y();
if(code_seen('Z')) disable_z();
#if ((E_ENABLE_PIN != X_ENABLE_PIN) && (E_ENABLE_PIN != Y_ENABLE_PIN)) // Only enable on boards that have seperate ENABLE_PINS
if(code_seen('E')) disable_e();
#endif
LCD_MESSAGEPGM("Partial Release");
}
}
break;
case 85: // M85
@ -979,7 +1009,11 @@ FORCE_INLINE void process_commands()
case 201: // M201
for(int8_t i=0; i < NUM_AXIS; i++)
{
if(code_seen(axis_codes[i])) axis_steps_per_sqr_second[i] = code_value() * axis_steps_per_unit[i];
if(code_seen(axis_codes[i]))
{
max_acceleration_units_per_sq_second[i] = code_value();
axis_steps_per_sqr_second[i] = code_value() * axis_steps_per_unit[i];
}
}
break;
#if 0 // Not used for Sprinter/grbl gen6
@ -1049,6 +1083,12 @@ FORCE_INLINE void process_commands()
}
break;
#endif //PIDTEMP
case 302: // finish all moves
{
allow_cold_extrudes(true);
}
break;
case 400: // finish all moves
{
st_synchronize();
@ -1146,6 +1186,7 @@ FORCE_INLINE void get_arc_coordinates()
void prepare_move()
{
if (min_software_endstops) {
if (destination[X_AXIS] < 0) destination[X_AXIS] = 0.0;
if (destination[Y_AXIS] < 0) destination[Y_AXIS] = 0.0;
@ -1162,6 +1203,7 @@ void prepare_move()
for(int8_t i=0; i < NUM_AXIS; i++) {
current_position[i] = destination[i];
}
previous_millis_cmd = millis();
}
void prepare_arc_move(char isclockwise) {
@ -1176,6 +1218,7 @@ void prepare_arc_move(char isclockwise) {
for(int8_t i=0; i < NUM_AXIS; i++) {
current_position[i] = destination[i];
}
previous_millis_cmd = millis();
}
void manage_inactivity(byte debug)
@ -1183,16 +1226,38 @@ void manage_inactivity(byte debug)
if( (millis()-previous_millis_cmd) > max_inactive_time )
if(max_inactive_time)
kill();
if( (millis()-previous_millis_cmd) > stepper_inactive_time )
if(stepper_inactive_time)
if( (millis()-last_stepperdisabled_time) > stepper_inactive_time )
{
disable_x();
disable_y();
disable_z();
disable_e0();
disable_e1();
disable_e2();
if(previous_millis_cmd>last_stepperdisabled_time)
last_stepperdisabled_time=previous_millis_cmd;
else
{
if( (X_ENABLE_ON && (READ(X_ENABLE_PIN)!=0)) || (!X_ENABLE_ON && READ(X_ENABLE_PIN)==0) )
enquecommand(DEFAULT_STEPPER_DEACTIVE_COMMAND);
last_stepperdisabled_time=millis();
}
}
#ifdef EXTRUDER_RUNOUT_PREVENT
if( (millis()-previous_millis_cmd) > EXTRUDER_RUNOUT_SECONDS*1000 )
if(degHotend(active_extruder)>EXTRUDER_RUNOUT_MINTEMP)
{
bool oldstatus=READ(E_ENABLE_PIN);
enable_e();
float oldepos=current_position[E_AXIS];
float oldedes=destination[E_AXIS];
plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
current_position[E_AXIS]+EXTRUDER_RUNOUT_EXTRUDE*EXTRUDER_RUNOUT_ESTEPS/axis_steps_per_unit[E_AXIS],
EXTRUDER_RUNOUT_SPEED/60.*EXTRUDER_RUNOUT_ESTEPS/axis_steps_per_unit[E_AXIS], active_extruder);
current_position[E_AXIS]=oldepos;
destination[E_AXIS]=oldedes;
plan_set_e_position(oldepos);
previous_millis_cmd=millis();
//enquecommand(DEFAULT_STEPPER_DEACTIVE_COMMAND);
st_synchronize();
WRITE(E_ENABLE_PIN,oldstatus);
}
#endif
check_axes_activity();
}

1
Marlin/cardreader.h
Unescape Escape View File

@ -44,6 +44,7 @@ public:
bool cardOK ;
char filename[11];
bool filenameIsDir;
int lastnr; //last number of the autostart;
private:
SdFile root,*curDir,workDir,workDirParent,workDirParentParent;
Sd2Card card;

8
Marlin/cardreader.pde
Unescape Escape View File

@ -14,6 +14,7 @@ CardReader::CardReader()
autostart_atmillis=0;
autostart_stilltocheck=true; //the sd start is delayed, because otherwise the serial cannot answer fast enought to make contact with the hostsoftware.
lastnr=0;
//power to SD reader
#if SDPOWER > -1
SET_OUTPUT(SDPOWER);
@ -334,7 +335,7 @@ void CardReader::checkautostart(bool force)
if(!cardOK) //fail
return;
}
static int lastnr=0;
char autoname[30];
sprintf(autoname,"auto%i.g",lastnr);
for(int8_t i=0;i<(int)strlen(autoname);i++)
@ -431,10 +432,13 @@ void CardReader::updir()
void CardReader::printingHasFinished()
{
quickStop();
sdprinting = false;
stop_heating_wait=true;
if(SD_FINISHED_STEPPERRELEASE)
{
finishAndDisableSteppers();
//finishAndDisableSteppers();
enquecommand(SD_FINISHED_RELEASECOMMAND);
}
autotempShutdown();
}

26
Marlin/planner.cpp
Unescape Escape View File

@ -103,7 +103,9 @@ volatile unsigned char block_buffer_tail; // Index of the block to pro
//===========================================================================
//=============================private variables ============================
//===========================================================================
#ifdef PREVENT_DANGEROUS_EXTRUDE
bool allow_cold_extrude=false;
#endif
#ifdef XY_FREQUENCY_LIMIT
// Used for the frequency limit
static unsigned char old_direction_bits = 0; // Old direction bits. Used for speed calculations
@ -464,6 +466,22 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
target[Z_AXIS] = lround(z*axis_steps_per_unit[Z_AXIS]);
target[E_AXIS] = lround(e*axis_steps_per_unit[E_AXIS]);
#ifdef PREVENT_DANGEROUS_EXTRUDE
if(target[E_AXIS]!=position[E_AXIS])
if(degHotend(active_extruder)<EXTRUDE_MINTEMP && !allow_cold_extrude)
{
position[E_AXIS]=target[E_AXIS]; //behave as if the move really took place, but ignore E part
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM(" cold extrusion prevented");
}
if(labs(target[E_AXIS]-position[E_AXIS])>axis_steps_per_unit[E_AXIS]*EXTRUDE_MAXLENGTH)
{
position[E_AXIS]=target[E_AXIS]; //behave as if the move really took place, but ignore E part
SERIAL_ECHO_START;
SERIAL_ECHOLNPGM(" too long extrusion prevented");
}
#endif
// Prepare to set up new block
block_t *block = &block_buffer[block_buffer_head];
@ -778,3 +796,9 @@ uint8_t movesplanned()
return (block_buffer_head-block_buffer_tail + BLOCK_BUFFER_SIZE) & (BLOCK_BUFFER_SIZE - 1);
}
void allow_cold_extrudes(bool allow)
{
#ifdef PREVENT_DANGEROUS_EXTRUDE
allow_cold_extrude=allow;
#endif
}

12
Marlin/planner.h
Unescape Escape View File

@ -128,4 +128,16 @@ FORCE_INLINE block_t *plan_get_current_block()
block->busy = true;
return(block);
}
// Gets the current block. Returns NULL if buffer empty
FORCE_INLINE bool blocks_queued()
{
if (block_buffer_head == block_buffer_tail) {
return false;
}
else
return true;
}
void allow_cold_extrudes(bool allow);
#endif

12
Marlin/stepper.cpp
Unescape Escape View File

@ -757,10 +757,11 @@ void st_init()
sei();
}
// Block until all buffered steps are executed
void st_synchronize()
{
while(plan_get_current_block()) {
while( blocks_queued()) {
manage_heater();
manage_inactivity(1);
LCD_STATUS;
@ -804,3 +805,12 @@ void finishAndDisableSteppers()
disable_e1();
disable_e2();
}
void quickStop()
{
DISABLE_STEPPER_DRIVER_INTERRUPT();
while(blocks_queued())
plan_discard_current_block();
ENABLE_STEPPER_DRIVER_INTERRUPT();
}

2
Marlin/stepper.h
Unescape Escape View File

@ -67,5 +67,5 @@ void finishAndDisableSteppers();
extern block_t *current_block; // A pointer to the block currently being traced
void quickStop();
#endif

15
Marlin/temperature.cpp
Unescape Escape View File

@ -85,6 +85,7 @@ static unsigned long previous_millis_bed_heater;
#ifdef WATCHPERIOD
static int watch_raw[EXTRUDERS] = { -1000 }; // the first value used for all
static int watch_oldtemp[3] = {0,0,0};
static unsigned long watchmillis = 0;
#endif //WATCHPERIOD
@ -214,6 +215,19 @@ void manage_heater()
}
} // End extruder for loop
#ifdef WATCHPERIOD
if(watchmillis && millis() - watchmillis > WATCHPERIOD){
if(watch_oldtemp[TEMPSENSOR_HOTEND_0] >= degHotend(active_extruder)){
setTargetHotend(0,active_extruder);
LCD_MESSAGEPGM("Heating failed");
SERIAL_ECHO_START;
SERIAL_ECHOLN("Heating failed");
}else{
watchmillis = 0;
}
}
#endif
if(millis() - previous_millis_bed_heater < BED_CHECK_INTERVAL)
return;
previous_millis_bed_heater = millis();
@ -493,6 +507,7 @@ void setWatch()
for (int e = 0; e < EXTRUDERS; e++)
{
if(isHeatingHotend(e))
watch_oldtemp[TEMPSENSOR_HOTEND_0] = degHotend(0);
{
t = max(t,millis());
watch_raw[e] = current_raw[e];

7
Marlin/temperature.h
Unescape Escape View File

@ -23,6 +23,7 @@
#include "Marlin.h"
#include "fastio.h"
#include "planner.h"
#ifdef PID_ADD_EXTRUSION_RATE
#include "stepper.h"
#endif
@ -48,10 +49,10 @@ extern float Kp,Ki,Kd,Kc;
extern float pid_setpoint[EXTRUDERS];
#endif
#ifdef WATCHPERIOD
// #ifdef WATCHPERIOD
extern int watch_raw[EXTRUDERS] ;
extern unsigned long watchmillis;
#endif
// extern unsigned long watchmillis;
// #endif
//high level conversion routines, for use outside of temperature.cpp

15
Marlin/ultralcd.pde
Unescape Escape View File

@ -441,7 +441,7 @@ void MainMenu::showStatus()
force_lcd_update=false;
}
enum {ItemP_exit, ItemP_home, ItemP_origin, ItemP_preheat, ItemP_extrude, ItemP_disstep};
enum {ItemP_exit, ItemP_autostart,ItemP_disstep,ItemP_home, ItemP_origin, ItemP_preheat, ItemP_extrude};
//any action must not contain a ',' character anywhere, or this breaks:
#define MENUITEM(repaint_action, click_action) \
@ -462,6 +462,12 @@ void MainMenu::showPrepare()
case ItemP_exit:
MENUITEM( lcdprintPGM(" Main \003") , BLOCK;status=Main_Menu;beepshort(); ) ;
break;
case ItemP_autostart:
MENUITEM( lcdprintPGM(" Autostart") , BLOCK;card.lastnr=0;card.checkautostart(true);beepshort(); ) ;
break;
case ItemP_disstep:
MENUITEM( lcdprintPGM(" Disable Steppers") , BLOCK;enquecommand("M84");beepshort(); ) ;
break;
case ItemP_home:
MENUITEM( lcdprintPGM(" Auto Home") , BLOCK;enquecommand("G28 X-105 Y-105 Z0");beepshort(); ) ;
break;
@ -474,15 +480,14 @@ void MainMenu::showPrepare()
case ItemP_extrude:
MENUITEM( lcdprintPGM(" Extrude") , BLOCK;enquecommand("G92 E0");enquecommand("G1 F700 E50");beepshort(); ) ;
break;
case ItemP_disstep:
MENUITEM( lcdprintPGM(" Disable Steppers") , BLOCK;enquecommand("M84");beepshort(); ) ;
break;
default:
break;
}
line++;
}
updateActiveLines(ItemP_disstep,encoderpos);
updateActiveLines(ItemP_extrude,encoderpos);
}
enum {ItemT_exit,ItemT_speed,ItemT_flow,ItemT_nozzle,ItemT_fan};

Write Preview
Loading…
Cancel
Save