microlab
/
scube
1
1
Fork 0
Code Issues Pull Requests Releases Activity

Update bq Hephestos 2 config

Browse Source
2.0.x
João Brázio 9 years ago committed by Scott Lahteine
parent b0e47608e6
commit 19fb04d761
3 changed files with 35 additions and 31 deletions
Show Stats Download Patch File Download Diff File

40
Marlin/example_configurations/Hephestos_2/Configuration.h
Unescape Escape View File

@ -221,20 +221,20 @@
// The minimal temperature defines the temperature below which the heater will not be enabled It is used // The minimal temperature defines the temperature below which the heater will not be enabled It is used
// to check that the wiring to the thermistor is not broken. // to check that the wiring to the thermistor is not broken.
// Otherwise this would lead to the heater being powered on all the time. // Otherwise this would lead to the heater being powered on all the time.
#define HEATER_0_MINTEMP 5 #define HEATER_0_MINTEMP 15
#define HEATER_1_MINTEMP 5 //#define HEATER_1_MINTEMP 5
#define HEATER_2_MINTEMP 5 //#define HEATER_2_MINTEMP 5
#define HEATER_3_MINTEMP 5 //#define HEATER_3_MINTEMP 5
#define BED_MINTEMP 5 //#define BED_MINTEMP 5
// When temperature exceeds max temp, your heater will be switched off. // When temperature exceeds max temp, your heater will be switched off.
// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure! // This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!
// You should use MINTEMP for thermistor short/failure protection. // You should use MINTEMP for thermistor short/failure protection.
#define HEATER_0_MAXTEMP 250 #define HEATER_0_MAXTEMP 250
#define HEATER_1_MAXTEMP 275 //#define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275 //#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275 //#define HEATER_3_MAXTEMP 275
#define BED_MAXTEMP 150 //#define BED_MAXTEMP 150
// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS // If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
//#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R //#define HOTEND_WATTS (12.0*12.0/6.7) // P=U^2/R
@ -293,7 +293,7 @@
// all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis) // all forms of bed control obey this (PID, bang-bang, bang-bang with hysteresis)
// setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did, // setting this to anything other than 255 enables a form of PWM to the bed just like HEATER_BED_DUTY_CYCLE_DIVIDER did,
// so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED) // so you shouldn't use it unless you are OK with PWM on your bed. (see the comment on enabling PIDTEMPBED)
#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current //#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
#if ENABLED(PIDTEMPBED) #if ENABLED(PIDTEMPBED)
@ -344,7 +344,7 @@
*/ */
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed //#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================
@ -512,7 +512,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
// For M851 give a range for adjusting the Z probe offset // For M851 give a range for adjusting the Z probe offset
// //
#define Z_PROBE_OFFSET_RANGE_MIN -5 #define Z_PROBE_OFFSET_RANGE_MIN -2
#define Z_PROBE_OFFSET_RANGE_MAX 0 #define Z_PROBE_OFFSET_RANGE_MAX 0
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
@ -561,8 +561,8 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops false // If true, axis won't move to coordinates less than HOME_POS. #define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops false // If true, axis won't move to coordinates greater than the defined lengths below. #define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
@ -715,16 +715,16 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// default settings // default settings
#define DEFAULT_AXIS_STEPS_PER_UNIT {160, 160, 8000, 204.146} // default steps per unit for Ultimaker #define DEFAULT_AXIS_STEPS_PER_UNIT {160, 160, 8000, 203} // default steps per unit for Ultimaker
#define DEFAULT_MAX_FEEDRATE {200, 200, 3.3, 200} // (mm/sec) #define DEFAULT_MAX_FEEDRATE {250, 250, 2, 200} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {1000, 1000, 100, 3000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. #define DEFAULT_MAX_ACCELERATION {1000, 1000, 20, 1000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration in mm/s^2 for printing moves #define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration in mm/s^2 for retracts
#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves #define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously) // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
#define DEFAULT_XYJERK 15.0 // (mm/sec) #define DEFAULT_XYJERK 10.0 // (mm/sec)
#define DEFAULT_ZJERK 0.4 // (mm/sec) #define DEFAULT_ZJERK 0.4 // (mm/sec)
#define DEFAULT_EJERK 2.0 // (mm/sec) #define DEFAULT_EJERK 2.0 // (mm/sec)
@ -809,7 +809,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// - Total time printing // - Total time printing
// //
// This information can be viewed by the M78 command. // This information can be viewed by the M78 command.
//#define PRINTCOUNTER #define PRINTCOUNTER
//============================================================================= //=============================================================================
//============================= LCD and SD support ============================ //============================= LCD and SD support ============================
@ -889,7 +889,7 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the l
// //
// Use CRC checks and retries on the SD communication. // Use CRC checks and retries on the SD communication.
// //
//#define SD_CHECK_AND_RETRY #define SD_CHECK_AND_RETRY
// //
// ENCODER SETTINGS // ENCODER SETTINGS

14
Marlin/example_configurations/Hephestos_2/Configuration_adv.h
Unescape Escape View File

@ -286,7 +286,7 @@
//#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially. //#define QUICK_HOME //if this is defined, if both x and y are to be homed, a diagonal move will be performed initially.
// When G28 is called, this option will make Y home before X // When G28 is called, this option will make Y home before X
//#define HOME_Y_BEFORE_X #define HOME_Y_BEFORE_X
// @section machine // @section machine
@ -301,7 +301,7 @@
// Default stepper release if idle. Set to 0 to deactivate. // Default stepper release if idle. Set to 0 to deactivate.
// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. // Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true.
// Time can be set by M18 and M84. // Time can be set by M18 and M84.
#define DEFAULT_STEPPER_DEACTIVE_TIME 60 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
#define DISABLE_INACTIVE_X true #define DISABLE_INACTIVE_X true
#define DISABLE_INACTIVE_Y true #define DISABLE_INACTIVE_Y true
#define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished. #define DISABLE_INACTIVE_Z true // set to false if the nozzle will fall down on your printed part when print has finished.
@ -355,12 +355,12 @@
//=============================Additional Features=========================== //=============================Additional Features===========================
//=========================================================================== //===========================================================================
#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly //#define ENCODER_RATE_MULTIPLIER // If defined, certain menu edit operations automatically multiply the steps when the encoder is moved quickly
#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value //#define ENCODER_10X_STEPS_PER_SEC 75 // If the encoder steps per sec exceeds this value, multiply steps moved x10 to quickly advance the value
#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value //#define ENCODER_100X_STEPS_PER_SEC 160 // If the encoder steps per sec exceeds this value, multiply steps moved x100 to really quickly advance the value
//#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ //#define CHDK 4 //Pin for triggering CHDK to take a picture see how to use it here http://captain-slow.dk/2014/03/09/3d-printing-timelapses/
#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again //#define CHDK_DELAY 50 //How long in ms the pin should stay HIGH before going LOW again
// @section lcd // @section lcd
@ -374,7 +374,7 @@
#define SD_DETECT_INVERTED #define SD_DETECT_INVERTED
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers? #define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place. #define SD_FINISHED_RELEASECOMMAND "M104 S0\nM84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
#define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order. #define SDCARD_RATHERRECENTFIRST //reverse file order of sd card menu display. Its sorted practically after the file system block order.
// if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that. // if a file is deleted, it frees a block. hence, the order is not purely chronological. To still have auto0.g accessible, there is again the option to do that.

6
Marlin/example_configurations/Hephestos_2/readme.md
Unescape Escape View File

@ -5,4 +5,8 @@ NOTE: The look and feel of the Hephestos 2 while navigating the LCD menu will ch
## Changelog ## Changelog
* 2016/03/01 - Initial release * 2016/03/01 - Initial release
* 2016/03/21 - Activated four point auto leveling by default; updated miscellaneous z-probe values * 2016/03/21 - Activated 4-point auto leveling by default
Updated miscellaneous z-probe values
* 2016/06/21 - Disabled hot bed related options
Activated software endstops
SD printing now disables the heater when finished

Write Preview
Loading…
Cancel
Save