0af22549a6
Allow G33 to compile with no LCD
6 years ago
4237c3d9f8
[2.0.x] different bltouch init ( #11135 )
7 years ago
1367df2875
Replace double with float, optimize calculation
7 years ago
d960d448fa
Optimize calculations with LROUND
7 years ago
e0ab8acf19
Add "Marlin Dev Mode" option
7 years ago
c51e27d11d
Do a hard kill for failed homing moves ( #11161 )
7 years ago
90ba77ea0f
Lose the old HOMEAXIS macro
7 years ago
a431013eb7
Fix G33 compile warning
7 years ago
cce0523a95
[2.0.x] reset bltouch on home ( #11018 )
...
Added reset bltouch instead. This ensure properly stow even when in error.
7 years ago
e0276d2f32
Official STMicroelectronics Arduino Core STM32F4 HAL compatibility ( #11006 )
7 years ago
f2c3b0d476
Use bit flags for homed/known
7 years ago
86170e6a66
[2.0.x] Add O (optional) flag to G28/G29 ( #10913 )
7 years ago
f1cdfe3dfd
[2.0.x] stow bltouch before start homing ( #10987 )
7 years ago
6f330f397e
[2.0.x] Buffer overflow and scroll fix, UTF8 cleanup ( #10844 )
7 years ago
99ecdf59af
Smarter MIN, MAX, ABS macros
...
Use macros that explicitly avoid double-evaluation and can be used for any datatype, replacing `min`, `max`, `abs`, `fabs`, `labs`, and `FABS`.
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
306f0f2135
Move Stepper::synchronize to Planner ( #10713 )
...
Co-Authored-By: ejtagle <ejtagle@hotmail.com>
7 years ago
59fda986ea
Allow Z_AFTER_PROBING to be 0
7 years ago
f423e54f77
Strip trailing spaces
7 years ago
1c3d49afe0
Fix G28 with Z_AFTER_PROBING
...
Fix #10476
7 years ago
023385ca59
Merge pull request #10479 from thinkyhead/bf2_creality_power_loss_resume
...
[2.0.x] Creality3D Power-Loss Recovery
7 years ago
3396671011
[2.0.x] Reset LCD status to fallbacks ( #10470 )
...
* Remove obsolete strings
* Tweak some static consts
* Reset LCD status to fallbacks
7 years ago
11ab017dd0
Creality3D Power-Loss Recovery
7 years ago
7dcd0a1cff
Add R parameter to G28 to specify pre-raise
7 years ago
646aa20b43
Overhaul of G33 Delta Calibration ( #8822 )
7 years ago
ac2e0afb62
Low Point for delta calibration ( #10363 )
7 years ago
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
7 years ago
1a75165f35
For set_z_fade_height use set_bed_leveling_enabled
7 years ago
c1f58a238d
No delay in sensorless quick homing ( #10254 )
7 years ago
bc45fb6b13
Tweak use of move_z_after_probing
7 years ago
c352954882
Allow no raise after run_z_probe in probe_pt
7 years ago
8922b56b58
Fix some spelingz
7 years ago
a6feb58837
Delta support for multiple hotends with offsets ( #10118 )
7 years ago
14c03cb6f4
[2.0.x] Make MIN_PROBE_EDGE a general option (for electronic probes) ( #10069 )
...
Some probes don't work near the edges of the bed. This change promotes MIN_PROBE_EDGE to a general setting that applies to all probing functions.
7 years ago
28f1276286
[2.0.x] Add Z_AFTER_PROBING option ( #10058 )
...
Some "fix-mounted" probes need manual stowing. And after probing some may prefer to raise or lower the nozzle. This restores an old option but tailors it to allow raise or lower as preferred.
7 years ago
751785fc97
Followup to recent patches
...
- `M666` is static, not inline
- Disambiguate some stepper macros
7 years ago
f003173752
Fixup M666
...
Followup to d6df032
7 years ago
d6df0322c2
Update M666 for XYZ dual endstops
7 years ago
419d12ca1b
Add UNKNOWN_Z_NO_RAISE option
...
With this option enabled, Z won't ever be raised until after `G28` has been completed, and it won't raise if Z becomes unknown. This is good for machines whose beds fall when Z is powered off.
7 years ago
2057177184
Make enums into implicit char
7 years ago
a446433c87
Fix SENSORLESS_HOMING for Core Kinematics ( #9868 )
7 years ago
b2cf253a13
Add RESTORE_LEVELING_AFTER_G28 option
7 years ago
1d7f5be0ff
quick_home_xy sensorless homing
7 years ago
d4e4fe40e0
Add SENSORLESS_HOMING delay to quick_home_xy
...
Fix #9471
7 years ago
3af988a7f3
Add sensorless homing delay to home_z_safely
...
Based on #9705
7 years ago
8ffa0b24a4
Strip excess G28 debug logging
7 years ago
9019ea0fce
Option to force X or Y to home first when homing the other axis
7 years ago
133b38b93b
Complete M48 description ( #9631 )
7 years ago
a8c4174a13
M100 comment
7 years ago
1dcfe193ac
Optimize some serial strings
7 years ago
a5dfe08a81
Add precision to planner.xy_skew_factor so it doesn't print as 0.00
7 years ago
Scott Lahteine