2f35747f29
L6470 SPI daisy chain support ( #12895 )
6 years ago
e6805582a6
M569 to change stepping mode. Add new TMC section to LCD. ( #12884 )
6 years ago
7fde8d9d1e
Add CreatorPro / Makerbot / QIDI / etc and Mightboard RevE support ( #12855 )
...
- Fix a bug in MAXxxxx thermocouple temp reporting.
- Add support for 3-wire HD44780.
- Add support for PCA9533 RGB driver.
- Add configuration examples for FlashForge CreatorPro.
6 years ago
1a79878dff
Remove TMC_Z_CALIBRATION in favor of Z_STEPPER_AUTO_ALIGN
6 years ago
b402040059
Split bed size sanity check into two
6 years ago
813a4ea107
Add support for Mks Robin TFT display ( #12706 )
...
* Add support for MKS Robin TFT display
- Add support for MKS Robin TFT display and encoder for MKS Robin board.
- Generic 128x64 UI with x2 upscale is used (for now).
- Tested on MKS Robin TFT V2.0 with ST7789V controller.
6 years ago
54ba44ee37
Fix bad sanitycheck ( #12748 )
6 years ago
cfc5e96b4b
Move JD to Config.h (and fix jerk->eeprom bug) ( #12720 )
6 years ago
902d5b0f8b
Allow ExtUI to use LCD_SET_PROGRESS_MANUALLY ( #12628 )
6 years ago
9a4a463ec4
Sanity-check LIGHTWEIGHT_UI, move comment up ( #12630 )
6 years ago
b22716e938
M425 Backlash Correction ( #11061 )
6 years ago
fa47ce369a
Sanity-check for negative steps, feedrate, accel
6 years ago
50b2fbd031
Trinamic: Split stealthChop, improve driver monitoring, etc. ( #12582 )
6 years ago
aaf862aef2
Fix angles for disabled EDITABLE_SERVO_ANGLES ( #12559 )
6 years ago
8be91677df
Fix Skew factors ( #12555 )
...
- Ensure Skew factors are calculated from test square measurements
6 years ago
439a3e8463
Improve runout sensor, fix LIGHTWEIGHT_UI screen size ( #12544 )
6 years ago
fd2998efd5
Revert ADC_KEYPAD direction behavior ( #12508 )
6 years ago
d29cb09b3e
Fix a minor compile warning
6 years ago
c5642a894f
Fix ADC_KEYPAD middle button ( #12493 )
6 years ago
1f93d2bcf7
Fix LCD compile error, etc. ( #12472 )
6 years ago
93e958f695
Fix compile error with ZONESTAR_LCD+NO_LCD_MENUS ( #12466 )
6 years ago
7ee5894360
Allow float XY probe offsets
...
Responding to #12383
XY probe offsets should be integers because adding decimal points makes the code larger. But if decimals are very much wanted, this commit removes the old restriction.
6 years ago
d97e31db4c
Optimize Power-Loss Recovery ( #12440 )
6 years ago
ca21ac6b9b
Support two MAX6675 thermocouples ( #8686 )
6 years ago
d82c350de7
Miscellaneous LCD code renaming, reordering ( #12430 )
...
* Move special characters to language.h
* Apply some naming standards
* Clean up menu item draw functions
* Rename some Temperature methods
* UI => ExtUI
6 years ago
ebf585b673
Fix an old sanity check
6 years ago
0ee1a92971
Group status methods, share reset_status with Extensible UI ( #12414 )
...
* Group status methods, share reset_status with Extensible UI
* Move common DOGM code to headers
6 years ago
a3923424c7
Clean up LCD width/height determination
6 years ago
a0c795b097
Encapsulate common display code in a singleton ( #12395 )
...
* Encapsulate common LCD code in a singleton
* Depend more UBL code on UBL_DEVEL_DEBUGGING
- Since most users don't need the debugging on at all times, this helps reduce the default build size for UBL by over 2K, a little closer to fitting on 128K boards.
6 years ago
b60abc7c37
[2.0.x] Macro G-codes ( #9365 )
6 years ago
4ed6397e5d
More comprehensive NO_LCD_MENUS ( #12367 )
6 years ago
b169320a03
Clean trailing whitespace
6 years ago
6471a75a22
Combine more tool-change variables ( #12137 )
6 years ago
e574f01568
More advanced pause tweaks ( #12356 )
...
* Followup to LCD_TIMEOUT_TO_STATUS=0
* Make continuous purge screen fit 20x4
* Unify purge message modes
* Preserve last-set pause header mode
6 years ago
427bc64ba1
G28 O respects HOME_AFTER_DEACTIVATE
...
Addressing #11271
6 years ago
498dfa291e
Update and fix CHDK
6 years ago
d5ab4cd22a
Provide a default for Z_PROBE_LOW_POINT
6 years ago
82ff7c6542
Add a mesh edit menu for MBL / ABL-Bilinear
6 years ago
44fa7fb18c
Cleanups for leveling-related code
6 years ago
cd066bfeba
Extend error messages for E factors sanity-checks
6 years ago
c10edb0998
Update, correct sanity-checks for up to 6 extruders ( #12333 )
6 years ago
f5eab912ed
Apply #pragma once, misc cleanup ( #12322 )
...
* Apply #pragma once in headers
* Adjust some thermistors formatting
* Misc cleanup and formatting
6 years ago
d1ff22b983
Revive SCARA's home offset (unimplemented)
6 years ago
2c9586be0c
Clear up HAS_WORKSPACE_OFFSET meaning
6 years ago
5ba6607181
Fix keypad-related compile error ( #12306 )
6 years ago
3eb9838dca
Simplify TMC sanity-checks
6 years ago
31c28d0dd2
Drop pgm_read_*_near and let headers choose ( #12301 )
...
- Drop `pgm_read_*_near` and let headers choose.
- Define `USE_EXECUTE_COMMANDS_IMMEDIATE` as a conditional.
- Add `process_subcommands_now` for SRAM-based commands.
6 years ago
9f77df2590
Followup to menu refactor. TMC warnings, sanity. ( #12288 )
...
- Followup fixes for menu refactor
- Fix TMC sanity checks, unused var warnings
6 years ago
3583e2b449
Followup to Menu Refactor ( #12275 )
6 years ago
5536228359
G34 Auto-align multi-stepper Z axis ( #11302 )
6 years ago
Bob Kuhn