2ea779e560
Allow bed probe sanity checks to run
7 years ago
d24b1190bd
Don't use Z_MIN_PROBE_ENDSTOP on DELTA
7 years ago
e34c6827ea
Init MIXING virtual tools as switching
7 years ago
a9ecb975b2
Apply LINEAR_UNIT to M503 output for M200
7 years ago
d95ee0f003
Merge pull request #8551 from revilor/bugfix-2.0.x
...
MK2_MULTIPLEXER does not require E2/E3 stepper pins
7 years ago
80ada58818
One fewer function call in probe_pt
7 years ago
92a0dc552a
MK2_MULTIPLEXER does not require E2/E3 stepper pins
7 years ago
b49acce035
Tweaks for lcd_external_control
7 years ago
1ef1052ae1
Phatter arrows for Z offset overlay
7 years ago
5926c9c97b
Followup for MESH_EDIT_GFX_OVERLAY
7 years ago
ab03a31cc9
Patch G0/G1 for NANODLP_Z_SYNC
7 years ago
a766dfb3b1
Merge pull request #8536 from thinkyhead/bf2_nanodlp_z_move_sync
...
[2.0.x] Implement NANODLP_Z_SYNC for 2.0.x
7 years ago
01e207213f
Fix MK2_MULTIPLEXER stepper indirection
7 years ago
ec04cf27d3
Fix the G26 out of scope identifiers in the v2.0.0 branch ( #8543 )
...
These changes may need to be warmed over. I tried to fix things with
the least amount of disruption. I just wanted to get the bugfix_v2.0.0
branch working for people again.
7 years ago
dc82babe8e
Implement NANODLP_Z_SYNC for 2.0.x
7 years ago
c6b0c104bb
Adapt G26 to work for all meshes
7 years ago
5ce7f23afa
Config option G26_MESH_VALIDATION for all meshes
7 years ago
c19eb33408
Move G26 to gcode sub-folder
7 years ago
a03f93bab4
Fix fan kickstart
7 years ago
9e3c41f9e8
Tweak fan kickstart / speed code
7 years ago
118ac61e59
[2.0.x] Tool change bad behaviour fix
...
Previous fix did not work as expected when axeis not homed. It raise Z but never return to original position
7 years ago
c35d27f77c
Merge pull request #8299 from tcm0116/2.0.x-BIQU_BQ111-A4
...
[2.0.x] Add BIQU BQ111-A4 board
7 years ago
1685cd193b
Tweak char_mode init
7 years ago
9406c87a97
Fix up LCD init / charset
7 years ago
fa577392b2
Add BIQU BQ111-A4 board
7 years ago
c2fc78c3a8
#ifndef => #if !PIN_EXISTS
7 years ago
c613a1ed38
Fix indentation, stepper.h dependency, etc.
7 years ago
f011a32771
Board definitions for Ultratronics Pro v1.0
7 years ago
9dad534f02
fixed
7 years ago
4371345cbe
Don't re-init graphical LCD after boot screen
...
Followup to 13a3fb1acc
7 years ago
56c02b7f59
Shift register buttons question
...
Can LCD shift registers keep up with faster MCUs?
7 years ago
3994d3b935
General cosmetic LCD
7 years ago
617993d0ea
Patch for !!TEST (was _BV once?)
7 years ago
3269d8dd62
Tweak M42 var
7 years ago
bb1a6eea88
Remove pin count check for MIGTHYBOARD_REVE
...
Remove assert and unused code since it is implemented in pinsDebug_plus_70.h
7 years ago
1ce0fb336b
Patch Max7219_LED_Set input args
7 years ago
a61127a421
[2.0.x] tool change bad behaviours
...
This will solve 2 issues on tool change.
1) when no home is done ("no_move" is set) tool change should never move X & Y because... I don't know where I am...only Z should be adjusted to avoid bed collision if other nozzle is lower than current.
Since no move no bed level matrix should be applied
2) When SWITCHING_NOZZLE is enabled and system is homed there are two movements to go to destination, but first can move Z to older position and then crash on the bed
7 years ago
e2724c68ab
Update pins_RURAMPS4D.h
...
Add and bugfix pins
7 years ago
9770062309
Merge pull request #8463 from thinkyhead/bf2_32bit_M42
...
[2.0.x] Updates to Anet A8 configurations
7 years ago
3066655727
Try port*100+pin, fix config dependency
7 years ago
ba8bc7ea80
Cosmetic tweaks
7 years ago
f409147116
Fix P2_04, P2_05
7 years ago
a28ccabe2a
M42 P1.20 fix
7 years ago
33912fa7e8
Update Temperature::setPwmFrequency prototype to match source
...
Introduced with #8446
7 years ago
b9327a4d16
Misc. general cleanup
7 years ago
8836623e0f
Fix `sq`/`min`/`max` macros after platform headers
7 years ago
fe4f009fdd
32-bit unless…
7 years ago
25af9decfe
Remove enum.h include of MarlinConfig.h
7 years ago
1d4571b88d
Dependency adjustments
7 years ago
550f1025f0
Try using <Arduino.h> everywhere
7 years ago
c0000a0cdc
Move servo code to modules/servo.*
7 years ago
81bc428b48
Don't compile custom u8g without DOGLCD
7 years ago
c14000775b
PWM fixes, slow down fan update
...
include LPC1768 syntax for M42
couple more pin_t changes
consistency
change M42 to R, P format
Revert "change M42 to R, P format"
This reverts commit 01f12f579ec9ccc1bb9126e68d2c86449e9b7edf.
7 years ago
60adc6ff02
Display filwidth ratio in terms of E mm
7 years ago
6e533748eb
Fixes #8472
7 years ago
485abb023b
Merge pull request #8456 from thinkyhead/bf2_wednesday_tweaks
...
[2.0] No retroactive adjustment with M851 Z
7 years ago
3bba7d60f3
No retroactive changes with M851 Z
...
If using babystep to adjust the Z probe offset, the axis will move and the mesh will be updated at the same time, causing a doubling of the Z offset over the rest of the print.
To correct for this, the current Z position would need to be modified in the opposite direction, canceling out the additional Z offset added to the mesh. This would be confusing to users, and moreover it would not be accurate without also taking the current Z fade level and current Z height into account.
It might make sense to change the mesh in the case where no babystepping is taking place, but this could be considered an undesirable side-effect of changing the `zprobe_zoffset`.
One way to remedy this would be to return to storing the mesh with `zprobe_zoffset` included, then subtracting `zprobe_zoffset` from the returned Z value. Thus, a babystep moving the Z axis up 1mm would subtract 1 from `zprobe_zoffset` while adding 1 to all mesh Z values.
Without including the `zprobe_zoffset` in the `z_values` there is no safe way to alter the mesh in conjunction with babystepping, although it's fine without it.
7 years ago
32512332df
Apply some formatting
7 years ago
7dacc999b9
Remove obsolete show_bootscreen var
7 years ago
9729528d13
Update UBL's Delta Probable locations
...
This is a non-intuitive change. @oldmcg says in this post https://github.com/MarlinFirmware/Marlin/issues/7572#issuecomment-340641207 that using DELTA_PRINTABLE_RADIUS is better than DELTA_PROBABLE_RADIUS for setting the probe limits. This is because the automatic probe code checks all locations for being reachable by the probe prior to doing the probe.
7 years ago
d48cb6bf41
Apply coding standards to Max7219
7 years ago
bd8bcf06e7
Updates to Anet A8 configurations
...
Based on #8426
7 years ago
7eea000f4b
E0 auto fan fixes
7 years ago
b2dda096fe
Fix FILAMENT_LCD_DISPLAY for disabled state
7 years ago
1e8afb66b7
Fix a planner comment
7 years ago
50f09cc029
Miscellaneous cleanup
7 years ago
63257dc083
Fix M503 output for M145
...
Fixes #7978
7 years ago
0918dae66e
Add OV() macro for use in thermistor tables
7 years ago
24057270a3
Merge pull request #8420 from RowanMeara/rm-dithering-2.0.x
...
[2.0.x] Fix Software Fan PWM
7 years ago
5079a02c90
Add HAL_SERVO_LIB to HAL_Due.h
7 years ago
9c3761047e
Merge pull request #8434 from thinkyhead/bf2_fix_M32_subroutines
...
[2.0] Fix 'M32 P' subroutines
7 years ago
e0d367f1fb
Fix M32 P subroutine handling
7 years ago
9f8b4c5ee8
Patch SD lib files for readability
7 years ago
2c8c30437e
Fix parser parameter value handling
7 years ago
6131533157
Change dithering behavior to intended.
7 years ago
e70b44dc0b
Make sure leveled[] is defined for later use
7 years ago
54774841ba
Merge pull request #8416 from thinkyhead/bf2_M114_DETAIL
...
[2.0] Add M114_DETAIL to Configuration_adv.h
7 years ago
009e3a7aa7
Add M114_DETAIL to Configuration_adv.h
7 years ago
6d6c3b1e97
Fix up REPRAPWORLD_KEYPAD defines
7 years ago
3f0a982b8c
Move Filament Width Sensor to Configuration_adv.h
7 years ago
b76e173205
Move test extrusion options under G26
7 years ago
14ebedca27
Drop unused LARGE_FLASH option
7 years ago
b7feb53e8a
Support for Extrudrboard in Printrboard Rev.F
7 years ago
91baca6abb
Patches for compiler warnings/errors
7 years ago
2f73dec077
Apply native workspace fixes for G92, G53-59
7 years ago
04abd8d459
Improve and clarify M428 code
7 years ago
c009a990e4
[2.0.x] Fix some 8-bit Teensyduino compile warnings ( #8385 )
...
* Fix some 8-bit Teensyduino compile warnings
-Override Teensyduino legacy NOT_A_PIN 127 define
-some fixups for Printrboard_RevF pins
* Proper cleanup of Printrboard Rev.F pins
* Apply LCD fixes to Printrboard v1
7 years ago
e8e92f8969
No leveling data in M114 if no leveling is enabled
7 years ago
f5d210c35c
Fix report_current_position
7 years ago
faaae7a1b2
Provide more clearance for BL-Touch probe
7 years ago
06ee6584fd
Remove offsets from soft endstops, tool change
7 years ago
c938273bd5
Coding standard patch of M290
7 years ago
98c1265e3b
Disable laser power when PWM goes to 0
7 years ago
d4a1154c25
Use do_blocking_move_to where possible
7 years ago
36426af564
Merge pull request #8356 from tcm0116/2.0.x-M600
...
[2.0.x] Normalize load/unload length in M600
7 years ago
1ed86adf9c
Cleanup around updatePID
7 years ago
75a58ee4b8
Fix position_is_reachable bug in waiting
7 years ago
e334efb2a7
PROBE_MANUALLY etc.
7 years ago
b6415dc169
finish
7 years ago
0efa66be0b
Updates to Traditional Chinese
...
From @cheton at #8347
7 years ago
Thomas Moore