daa712455b
Make sure MBL starts close to the bed
...
Fix #10390
7 years ago
4c8751727a
Fix M118 parameter handling
...
Fix #10388
7 years ago
3bc179a16f
Compress/update comments ubl_motion
...
…to fit more code on the screen and correct outdated commentary contrasting ABL.
7 years ago
646aa20b43
Overhaul of G33 Delta Calibration ( #8822 )
7 years ago
ac2e0afb62
Low Point for delta calibration ( #10363 )
7 years ago
57a899a412
[2.0.x] 6th-order jerk-controlled motion planning in real-time for AVR ( #10373 )
7 years ago
5676b187b4
Move etc/udev to buildroot/etc
...
Followup to #10375 . This is the appropriate place for any system etc folder additions.
7 years ago
44a03ecfc9
Add Linux compatibility for Arduino boards ( #10375 )
7 years ago
85014cd132
[2.0.x] LPC1768 - automatic selection of upload disk ( #10374 )
7 years ago
8669dba5e6
Merge pull request #10172 from noingwhat/2.0.x-Filament-Change-Acceleration
...
[2.0.x] Filament load/unload add acceleration for Bowden
7 years ago
472ab0cc24
Tweak RAMPS SDSS pins
7 years ago
b94c8defee
Provide additional information about SMART-RAMPS board ( #10353 )
7 years ago
6f8e228880
Add RESET_PIN to pins_RAMPS_SMART.h
7 years ago
2d9b0a66fe
Add Filament Change accelerations
7 years ago
71d3523254
Add Filament Change accelerations to example configs
7 years ago
dcb1f1f452
Merge pull request #10351 from thinkyhead/bf2_z_probe_low_point
...
[2.0.x] Z_PROBE_LOW_POINT to prevent probe/bed damage
7 years ago
8b8ad14178
Add Z_PROBE_LOW_POINT to prevent damage
7 years ago
82dafbba33
Add Z_PROBE_LOW_POINT to example configs
7 years ago
a731a723e8
Better i3-2020 Z_PROBE_OFFSET_FROM_EXTRUDER
7 years ago
26cc12eaa4
Resolve corruption of Max7219 Debug LED Matrix
7 years ago
72c15a5cc9
Add --no-track to mfnew git script
7 years ago
dca69efc11
Update Bed PID comments
7 years ago
56486c5c0e
Apply const to manage_inactivity
7 years ago
a6485456df
Fix LIGHTWEIGHT_UI with UBL
...
See https://github.com/MarlinFirmware/Marlin/issues/10317#issuecomment-379100702
7 years ago
e02fc4f1d6
Better RESTORE_LEVELING_AFTER_G28 sanity-check
...
As suggested by @GMagician
7 years ago
44a697ab04
Set STM32F1 TEMP_TIMER_FREQUENCY to 1K
...
Responding to https://github.com/MarlinFirmware/Marlin/pull/8833#issuecomment-379426803
7 years ago
cec6e19099
Add RepRapPro Huxley configuration
...
Based on #10343 by @indazoo
7 years ago
9ff4e9e1e6
Patch _IS_HW_SPI so defined() works
7 years ago
cea398849e
Tweak to gcode_line_error/return
7 years ago
4382f2124d
Merge pull request #10337 from ejtagle/bugfix-2.0.x
...
[2.0.x] 6th-order jerk-controlled motion planning in real-time
7 years ago
a29adde5c0
Implement BEZIER_JERK_CONTROL
...
Enable 6th-order jerk-controlled motion planning in real-time.
Only for 32bit MCUs. (AVR simply does not have enough processing power for this!)
7 years ago
5932df7ea1
Add BEZIER_JERK_CONTROL to example configs
7 years ago
93524c1994
Merge pull request #10045 from Lenbok/2.0.x-monitor_chamber_temperature_and_auto_fan
...
[2.0.x] Monitor chamber temperature, with auto fan control.
7 years ago
0e8242180d
Chamber temperature monitoring and auto fan control.
...
This is an initial cut for feedback, updated for 2.0.x.
Chamber temperature is currently reported along with hot end and bed
temperatures to serial. The format is just like that used for hot end
and bed temperatures, but using 'C' prefix. As there is no heater,
target is always 0. Is this appropriate, is there a better way to report
chamber temperatures?
Chamber temperatures are not reported on the LCD in any way.
When auto chamber fan is enabled, it currently just uses the same
temperature threshold as the other auto controlled fans.
As the chamber temperature is not connected to any heater, it doesn't
undergo mintemp/maxtemp monitoring. This would need to change in the
future if chamber heating became a feature.
7 years ago
5b3bda1c16
Add Chamber Temp options to example configs
7 years ago
acda4ecb20
Fix DUE Trinamic SW/HW SPI sanity check ( #10336 )
7 years ago
ab715c70d1
TMC SPI sanity-check and pins debugging ( #10324 )
7 years ago
4dc7e64789
Update Slovak language
...
Based on #10313 by @rmoravcik
7 years ago
0dccf9ea6a
Merge pull request #10318 from marcio-ao/pr-einsy-retro-tmc2130
...
[2.0.x] Fix TMC2130 DIAG1 active high, Einsy Retro
7 years ago
2efc072fdb
Clear progress bar on completion ( #10333 )
...
Fix #10330
7 years ago
6ce060cfe0
[2.0.x] Update language_it.h ( #10322 )
...
Updated to #10296
7 years ago
9356cf648f
Added support for Einsy Retro
...
http://reprap.org/wiki/EinsyRetro
7 years ago
75037493fa
Default active low for TMC2130 DIAG1 ( #10294 )
...
- Added sanity check to inform users to set the endstop to inverting
when using SENSORLESS_HOMING
7 years ago
e8e60263c8
Scale feedrate (mm/s to deg/s) for SCARA
7 years ago
051303ad42
Russian language updates
...
From #10311 by @anton-piliugin
7 years ago
386bc71d57
Merge pull request #10173 from noingwhat/2.0.x-Continuous-Purge
...
[2.0.x] Continuous Purge
7 years ago
2fa0a73c2c
Implement filament change continuous purge
7 years ago
d133ad61f3
Add continuous purge to example configs
7 years ago
4b25543633
Backtrace formatting cleanup
7 years ago
902c885782
Switch to TMC2130 compatible hardware SPI & misc ( #10299 )
7 years ago
Scott Lahteine