Fix analogWrite ambiguity

Marlin/src/HAL/HAL_ESP32/HAL.cpp

@@ -192,7 +192,7 @@ void HAL_adc_start_conversion(uint8_t adc_pin) {
   HAL_adc_result = mv*1023.0/3300.0;
 }
 
-void analogWrite(int pin, int value) {
+void analogWrite(pin_t pin, int value) {
 
   if (!PWM_PIN(pin)) return;
 

Marlin/src/HAL/HAL_ESP32/HAL.h

@@ -98,7 +98,7 @@ void _delay_ms(int delay);
 
 int freeMemory(void);
 
-void analogWrite(int pin, int value);
+void analogWrite(pin_t pin, int value);
 
 // EEPROM
 void eeprom_write_byte(uint8_t *pos, unsigned char value);

Marlin/src/feature/caselight.cpp

@@ -71,7 +71,7 @@ void update_case_light() {
 
     #if DISABLED(CASE_LIGHT_NO_BRIGHTNESS)
       if (PWM_PIN(CASE_LIGHT_PIN))
-        analogWrite(CASE_LIGHT_PIN, n10ct);
+        analogWrite(pin_t(CASE_LIGHT_PIN), n10ct);
       else
     #endif
       {

Marlin/src/feature/controllerfan.cpp

@@ -81,7 +81,7 @@ void controllerfan_update() {
 
     // allows digital or PWM fan output to be used (see M42 handling)
     WRITE(CONTROLLER_FAN_PIN, speed);
-    analogWrite(CONTROLLER_FAN_PIN, speed);
+    analogWrite(pin_t(CONTROLLER_FAN_PIN), speed);
   }
 }
 

Marlin/src/feature/spindle_laser.cpp

@@ -41,7 +41,7 @@ void SpindleLaser::init() {
   #endif
   #if ENABLED(SPINDLE_LASER_PWM) && PIN_EXISTS(SPINDLE_LASER_PWM)
     SET_PWM(SPINDLE_LASER_PWM_PIN);
-    analogWrite(SPINDLE_LASER_PWM_PIN, SPINDLE_LASER_PWM_INVERT ? 255 : 0);  // set to lowest speed
+    analogWrite(pin_t(SPINDLE_LASER_PWM_PIN), SPINDLE_LASER_PWM_INVERT ? 255 : 0);  // set to lowest speed
   #endif
 }
 
@@ -55,7 +55,7 @@ void SpindleLaser::init() {
   void SpindleLaser::set_ocr(const uint8_t ocr) {
     WRITE(SPINDLE_LASER_ENA_PIN, SPINDLE_LASER_ACTIVE_HIGH); // turn spindle on (active low)
     #if ENABLED(SPINDLE_LASER_PWM)
-      analogWrite(SPINDLE_LASER_PWM_PIN, (SPINDLE_LASER_PWM_INVERT) ? 255 - ocr : ocr);
+      analogWrite(pin_t(SPINDLE_LASER_PWM_PIN), (SPINDLE_LASER_PWM_INVERT) ? 255 - ocr : ocr);
     #endif
   }
 
@@ -75,8 +75,8 @@ void SpindleLaser::update_output() {
       set_ocr(ocr_val & 0xFF);                                                            // ...limited to Atmel PWM max
     }
     else {                                                                                // Convert RPM to PWM duty cycle
-      WRITE(SPINDLE_LASER_ENA_PIN, !SPINDLE_LASER_ACTIVE_HIGH);                         // Turn spindle off (active low)
-      analogWrite(SPINDLE_LASER_PWM_PIN, SPINDLE_LASER_PWM_INVERT ? 255 : 0);             // Only write low byte
+      WRITE(SPINDLE_LASER_ENA_PIN, !SPINDLE_LASER_ACTIVE_HIGH);                           // Turn spindle off (active low)
+      analogWrite(pin_t(SPINDLE_LASER_PWM_PIN), SPINDLE_LASER_PWM_INVERT ? 255 : 0);      // Only write low byte
     }
   #else
     WRITE(SPINDLE_LASER_ENA_PIN, ena ? SPINDLE_LASER_ACTIVE_HIGH : !SPINDLE_LASER_ACTIVE_HIGH);

Marlin/src/module/planner.cpp

@@ -1289,10 +1289,10 @@ void Planner::check_axes_activity() {
 
   #if ENABLED(BARICUDA)
     #if HAS_HEATER_1
-      analogWrite(HEATER_1_PIN, tail_valve_pressure);
+      analogWrite(pin_t(HEATER_1_PIN), tail_valve_pressure);
     #endif
     #if HAS_HEATER_2
-      analogWrite(HEATER_2_PIN, tail_e_to_p_pressure);
+      analogWrite(pin_t(HEATER_2_PIN), tail_e_to_p_pressure);
     #endif
   #endif
 }

Marlin/src/module/stepper.cpp

@@ -2502,7 +2502,7 @@ void Stepper::report_positions() {
         if (WITHIN(driver, 0, COUNT(motor_current_setting) - 1))
           motor_current_setting[driver] = current; // update motor_current_setting
 
-        #define _WRITE_CURRENT_PWM(P) analogWrite(MOTOR_CURRENT_PWM_## P ##_PIN, 255L * current / (MOTOR_CURRENT_PWM_RANGE))
+        #define _WRITE_CURRENT_PWM(P) analogWrite(pin_t(MOTOR_CURRENT_PWM_## P ##_PIN), 255L * current / (MOTOR_CURRENT_PWM_RANGE))
         switch (driver) {
           case 0:
             #if PIN_EXISTS(MOTOR_CURRENT_PWM_X)

Marlin/src/module/temperature.cpp

@@ -699,11 +699,11 @@ int16_t Temperature::getHeaterPower(const int8_t heater) {
         SBI(fanState, pgm_read_byte(&fanBit[CHAMBER_FAN_INDEX]));
     #endif
 
-    #define _UPDATE_AUTO_FAN(P,D,A) do{             \
-      if (PWM_PIN(P##_AUTO_FAN_PIN) && A < 255)     \
-        analogWrite(P##_AUTO_FAN_PIN, D ? A : 0);   \
-      else                                          \
-        WRITE(P##_AUTO_FAN_PIN, D);                 \
+    #define _UPDATE_AUTO_FAN(P,D,A) do{                  \
+      if (PWM_PIN(P##_AUTO_FAN_PIN) && A < 255)          \
+        analogWrite(pin_t(P##_AUTO_FAN_PIN), D ? A : 0); \
+      else                                               \
+        WRITE(P##_AUTO_FAN_PIN, D);                      \
     }while(0)
 
     uint8_t fanDone = 0;