Merge pull request #6031 from thinkyhead/rc_mbl_z_unhack

MBL: Disable sw endstops instead of altering Z
2.0.x
Scott Lahteine 8 years ago committed by GitHub
commit d15f25539b

@ -369,4 +369,6 @@
#undef Z_MIN_PROBE_ENDSTOP #undef Z_MIN_PROBE_ENDSTOP
#endif #endif
#define HAS_SOFTWARE_ENDSTOPS (ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS))
#endif //CONDITIONALS_LCD_H #endif //CONDITIONALS_LCD_H

@ -709,6 +709,11 @@
#ifndef Z_CLEARANCE_BETWEEN_PROBES #ifndef Z_CLEARANCE_BETWEEN_PROBES
#define Z_CLEARANCE_BETWEEN_PROBES Z_HOMING_HEIGHT #define Z_CLEARANCE_BETWEEN_PROBES Z_HOMING_HEIGHT
#endif #endif
#if Z_CLEARANCE_BETWEEN_PROBES > Z_HOMING_HEIGHT
#define MANUAL_PROBE_HEIGHT Z_CLEARANCE_BETWEEN_PROBES
#else
#define MANUAL_PROBE_HEIGHT Z_HOMING_HEIGHT
#endif
#if IS_KINEMATIC #if IS_KINEMATIC
// Check for this in the code instead // Check for this in the code instead

@ -705,16 +705,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -725,6 +721,11 @@
#define Y_MAX_POS 200 #define Y_MAX_POS 200
#define Z_MAX_POS 200 #define Z_MAX_POS 200
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -750,9 +751,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -304,7 +304,7 @@ extern float current_position[NUM_AXIS];
extern float soft_endstop_min[XYZ]; extern float soft_endstop_min[XYZ];
extern float soft_endstop_max[XYZ]; extern float soft_endstop_max[XYZ];
#if ENABLED(min_software_endstops) || ENABLED(max_software_endstops) #if HAS_SOFTWARE_ENDSTOPS
extern bool soft_endstops_enabled; extern bool soft_endstops_enabled;
void clamp_to_software_endstops(float target[XYZ]); void clamp_to_software_endstops(float target[XYZ]);
#else #else

@ -414,7 +414,7 @@ float filament_size[EXTRUDERS] = ARRAY_BY_EXTRUDERS1(DEFAULT_NOMINAL_FILAMENT_DI
#endif #endif
// Software Endstops are based on the configured limits. // Software Endstops are based on the configured limits.
#if ENABLED(min_software_endstops) || ENABLED(max_software_endstops) #if HAS_SOFTWARE_ENDSTOPS
bool soft_endstops_enabled = true; bool soft_endstops_enabled = true;
#endif #endif
float soft_endstop_min[XYZ] = { X_MIN_POS, Y_MIN_POS, Z_MIN_POS }, float soft_endstop_min[XYZ] = { X_MIN_POS, Y_MIN_POS, Z_MIN_POS },
@ -3450,7 +3450,7 @@ inline void gcode_G28() {
stepper.synchronize(); stepper.synchronize();
// Disable the leveling matrix before homing // Disable the leveling matrix before homing
#if PLANNER_LEVELING #if PLANNER_LEVELING || ENABLED(MESH_BED_LEVELING)
set_bed_leveling_enabled(false); set_bed_leveling_enabled(false);
#endif #endif
@ -3464,31 +3464,6 @@ inline void gcode_G28() {
extruder_duplication_enabled = false; extruder_duplication_enabled = false;
#endif #endif
/**
* For mesh bed leveling deactivate the mesh calculations, will be turned
* on again when homing all axis
*/
#if ENABLED(MESH_BED_LEVELING)
float pre_home_z = MESH_HOME_SEARCH_Z;
if (mbl.active()) {
#if ENABLED(DEBUG_LEVELING_FEATURE)
if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("MBL was active");
#endif
// Use known Z position if already homed
if (axis_homed[X_AXIS] && axis_homed[Y_AXIS] && axis_homed[Z_AXIS]) {
set_bed_leveling_enabled(false);
pre_home_z = current_position[Z_AXIS];
}
else {
mbl.set_active(false);
current_position[Z_AXIS] = pre_home_z;
}
#if ENABLED(DEBUG_LEVELING_FEATURE)
if (DEBUGGING(LEVELING)) DEBUG_POS("Set Z to pre_home_z", current_position);
#endif
}
#endif
setup_for_endstop_or_probe_move(); setup_for_endstop_or_probe_move();
#if ENABLED(DEBUG_LEVELING_FEATURE) #if ENABLED(DEBUG_LEVELING_FEATURE)
if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("> endstops.enable(true)"); if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("> endstops.enable(true)");
@ -3620,43 +3595,14 @@ inline void gcode_G28() {
// Enable mesh leveling again // Enable mesh leveling again
#if ENABLED(MESH_BED_LEVELING) #if ENABLED(MESH_BED_LEVELING)
if (mbl.has_mesh()) { if (mbl.reactivate()) {
#if ENABLED(DEBUG_LEVELING_FEATURE) set_bed_leveling_enabled(true);
if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("MBL has mesh");
#endif
if (home_all_axis || (axis_homed[X_AXIS] && axis_homed[Y_AXIS] && homeZ)) { if (home_all_axis || (axis_homed[X_AXIS] && axis_homed[Y_AXIS] && homeZ)) {
#if ENABLED(DEBUG_LEVELING_FEATURE)
if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("MBL Z homing");
#endif
current_position[Z_AXIS] = MESH_HOME_SEARCH_Z
#if Z_HOME_DIR > 0
+ Z_MAX_POS
#endif
;
SYNC_PLAN_POSITION_KINEMATIC();
mbl.set_active(true);
#if ENABLED(MESH_G28_REST_ORIGIN) #if ENABLED(MESH_G28_REST_ORIGIN)
current_position[Z_AXIS] = 0.0; current_position[Z_AXIS] = LOGICAL_Z_POSITION(Z_MIN_POS);
set_destination_to_current(); set_destination_to_current();
line_to_destination(homing_feedrate_mm_s[Z_AXIS]); line_to_destination(homing_feedrate_mm_s[Z_AXIS]);
stepper.synchronize(); stepper.synchronize();
#if ENABLED(DEBUG_LEVELING_FEATURE)
if (DEBUGGING(LEVELING)) DEBUG_POS("MBL Rest Origin", current_position);
#endif
#else
planner.unapply_leveling(current_position);
#if ENABLED(DEBUG_LEVELING_FEATURE)
if (DEBUGGING(LEVELING)) DEBUG_POS("MBL adjusted MESH_HOME_SEARCH_Z", current_position);
#endif
#endif
}
else if ((axis_homed[X_AXIS] && axis_homed[Y_AXIS] && axis_homed[Z_AXIS]) && (homeX || homeY)) {
current_position[Z_AXIS] = pre_home_z;
SYNC_PLAN_POSITION_KINEMATIC();
mbl.set_active(true);
planner.unapply_leveling(current_position);
#if ENABLED(DEBUG_LEVELING_FEATURE)
if (DEBUGGING(LEVELING)) DEBUG_POS("MBL Home X or Y", current_position);
#endif #endif
} }
} }
@ -3664,16 +3610,16 @@ inline void gcode_G28() {
clean_up_after_endstop_or_probe_move(); clean_up_after_endstop_or_probe_move();
#if ENABLED(DEBUG_LEVELING_FEATURE)
if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("<<< gcode_G28");
#endif
// Restore the active tool after homing // Restore the active tool after homing
#if HOTENDS > 1 #if HOTENDS > 1
tool_change(old_tool_index, 0, true); tool_change(old_tool_index, 0, true);
#endif #endif
report_current_position(); report_current_position();
#if ENABLED(DEBUG_LEVELING_FEATURE)
if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("<<< gcode_G28");
#endif
} }
#if HAS_PROBING_PROCEDURE #if HAS_PROBING_PROCEDURE
@ -3690,25 +3636,21 @@ inline void gcode_G28() {
inline void _mbl_goto_xy(const float &x, const float &y) { inline void _mbl_goto_xy(const float &x, const float &y) {
const float old_feedrate_mm_s = feedrate_mm_s; const float old_feedrate_mm_s = feedrate_mm_s;
feedrate_mm_s = homing_feedrate_mm_s[Z_AXIS];
current_position[Z_AXIS] = MESH_HOME_SEARCH_Z #if MANUAL_PROBE_HEIGHT > 0
#if Z_CLEARANCE_BETWEEN_PROBES > Z_HOMING_HEIGHT feedrate_mm_s = homing_feedrate_mm_s[Z_AXIS];
+ Z_CLEARANCE_BETWEEN_PROBES current_position[Z_AXIS] = LOGICAL_Z_POSITION(Z_MIN_POS) + MANUAL_PROBE_HEIGHT;
#elif Z_HOMING_HEIGHT > 0 line_to_current_position();
+ Z_HOMING_HEIGHT #endif
#endif
;
line_to_current_position();
feedrate_mm_s = MMM_TO_MMS(XY_PROBE_SPEED); feedrate_mm_s = MMM_TO_MMS(XY_PROBE_SPEED);
current_position[X_AXIS] = LOGICAL_X_POSITION(x); current_position[X_AXIS] = LOGICAL_X_POSITION(x);
current_position[Y_AXIS] = LOGICAL_Y_POSITION(y); current_position[Y_AXIS] = LOGICAL_Y_POSITION(y);
line_to_current_position(); line_to_current_position();
#if Z_CLEARANCE_BETWEEN_PROBES > 0 || Z_HOMING_HEIGHT > 0 #if MANUAL_PROBE_HEIGHT > 0
feedrate_mm_s = homing_feedrate_mm_s[Z_AXIS]; feedrate_mm_s = homing_feedrate_mm_s[Z_AXIS];
current_position[Z_AXIS] = LOGICAL_Z_POSITION(MESH_HOME_SEARCH_Z); current_position[Z_AXIS] = LOGICAL_Z_POSITION(Z_MIN_POS) + 0.2; // just slightly over the bed
line_to_current_position(); line_to_current_position();
#endif #endif
@ -3721,7 +3663,6 @@ inline void gcode_G28() {
void mbl_mesh_report() { void mbl_mesh_report() {
SERIAL_PROTOCOLLNPGM("Num X,Y: " STRINGIFY(MESH_NUM_X_POINTS) "," STRINGIFY(MESH_NUM_Y_POINTS)); SERIAL_PROTOCOLLNPGM("Num X,Y: " STRINGIFY(MESH_NUM_X_POINTS) "," STRINGIFY(MESH_NUM_Y_POINTS));
SERIAL_PROTOCOLLNPGM("Z search height: " STRINGIFY(MESH_HOME_SEARCH_Z));
SERIAL_PROTOCOLPGM("Z offset: "); SERIAL_PROTOCOL_F(mbl.z_offset, 5); SERIAL_PROTOCOLPGM("Z offset: "); SERIAL_PROTOCOL_F(mbl.z_offset, 5);
SERIAL_PROTOCOLLNPGM("\nMeasured points:"); SERIAL_PROTOCOLLNPGM("\nMeasured points:");
for (uint8_t py = 0; py < MESH_NUM_Y_POINTS; py++) { for (uint8_t py = 0; py < MESH_NUM_Y_POINTS; py++) {
@ -3757,6 +3698,10 @@ inline void gcode_G28() {
inline void gcode_G29() { inline void gcode_G29() {
static int probe_index = -1; static int probe_index = -1;
#if HAS_SOFTWARE_ENDSTOPS
static bool enable_soft_endstops;
#endif
const MeshLevelingState state = code_seen('S') ? (MeshLevelingState)code_value_byte() : MeshReport; const MeshLevelingState state = code_seen('S') ? (MeshLevelingState)code_value_byte() : MeshReport;
if (state < 0 || state > 5) { if (state < 0 || state > 5) {
SERIAL_PROTOCOLLNPGM("S out of range (0-5)."); SERIAL_PROTOCOLLNPGM("S out of range (0-5).");
@ -3788,33 +3733,34 @@ inline void gcode_G28() {
} }
// For each G29 S2... // For each G29 S2...
if (probe_index == 0) { if (probe_index == 0) {
// For the initial G29 S2 make Z a positive value (e.g., 4.0) #if HAS_SOFTWARE_ENDSTOPS
current_position[Z_AXIS] = MESH_HOME_SEARCH_Z // For the initial G29 S2 save software endstop state
#if Z_HOME_DIR > 0 enable_soft_endstops = soft_endstops_enabled;
+ Z_MAX_POS #endif
#endif
;
SYNC_PLAN_POSITION_KINEMATIC();
} }
else { else {
// For G29 S2 after adjusting Z. // For G29 S2 after adjusting Z.
mbl.set_zigzag_z(probe_index - 1, current_position[Z_AXIS]); mbl.set_zigzag_z(probe_index - 1, current_position[Z_AXIS]);
#if HAS_SOFTWARE_ENDSTOPS
soft_endstops_enabled = enable_soft_endstops;
#endif
} }
// If there's another point to sample, move there with optional lift. // If there's another point to sample, move there with optional lift.
if (probe_index < (MESH_NUM_X_POINTS) * (MESH_NUM_Y_POINTS)) { if (probe_index < (MESH_NUM_X_POINTS) * (MESH_NUM_Y_POINTS)) {
mbl.zigzag(probe_index, px, py); mbl.zigzag(probe_index, px, py);
_mbl_goto_xy(mbl.get_probe_x(px), mbl.get_probe_y(py)); _mbl_goto_xy(mbl.get_probe_x(px), mbl.get_probe_y(py));
#if HAS_SOFTWARE_ENDSTOPS
// Disable software endstops to allow manual adjustment
// If G29 is not completed, they will not be re-enabled
soft_endstops_enabled = false;
#endif
probe_index++; probe_index++;
} }
else { else {
// One last "return to the bed" (as originally coded) at completion // One last "return to the bed" (as originally coded) at completion
current_position[Z_AXIS] = MESH_HOME_SEARCH_Z current_position[Z_AXIS] = LOGICAL_Z_POSITION(Z_MIN_POS) + MANUAL_PROBE_HEIGHT;
#if Z_CLEARANCE_BETWEEN_PROBES > Z_HOMING_HEIGHT
+ Z_CLEARANCE_BETWEEN_PROBES
#elif Z_HOMING_HEIGHT > 0
+ Z_HOMING_HEIGHT
#endif
;
line_to_current_position(); line_to_current_position();
stepper.synchronize(); stepper.synchronize();
@ -3822,7 +3768,12 @@ inline void gcode_G28() {
SERIAL_PROTOCOLLNPGM("Mesh probing done."); SERIAL_PROTOCOLLNPGM("Mesh probing done.");
probe_index = -1; probe_index = -1;
mbl.set_has_mesh(true); mbl.set_has_mesh(true);
mbl.set_reactivate(true);
enqueue_and_echo_commands_P(PSTR("G28")); enqueue_and_echo_commands_P(PSTR("G28"));
#if HAS_BUZZER
lcd_buzz(200, 659);
lcd_buzz(200, 698);
#endif
} }
break; break;
@ -3871,14 +3822,8 @@ inline void gcode_G28() {
break; break;
case MeshReset: case MeshReset:
if (mbl.active()) { reset_bed_level();
current_position[Z_AXIS] -= MESH_HOME_SEARCH_Z; break;
planner.apply_leveling(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS]);
mbl.reset();
SYNC_PLAN_POSITION_KINEMATIC();
}
else
mbl.reset();
} // switch(state) } // switch(state)
@ -6427,10 +6372,8 @@ inline void gcode_M205() {
*/ */
inline void gcode_M211() { inline void gcode_M211() {
SERIAL_ECHO_START; SERIAL_ECHO_START;
#if ENABLED(min_software_endstops) || ENABLED(max_software_endstops) #if HAS_SOFTWARE_ENDSTOPS
if (code_seen('S')) soft_endstops_enabled = code_value_bool(); if (code_seen('S')) soft_endstops_enabled = code_value_bool();
#endif
#if ENABLED(min_software_endstops) || ENABLED(max_software_endstops)
SERIAL_ECHOPGM(MSG_SOFT_ENDSTOPS); SERIAL_ECHOPGM(MSG_SOFT_ENDSTOPS);
serialprintPGM(soft_endstops_enabled ? PSTR(MSG_ON) : PSTR(MSG_OFF)); serialprintPGM(soft_endstops_enabled ? PSTR(MSG_ON) : PSTR(MSG_OFF));
#else #else
@ -7946,7 +7889,7 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n
&& (delayed_move_time || current_position[X_AXIS] != xhome) && (delayed_move_time || current_position[X_AXIS] != xhome)
) { ) {
float raised_z = current_position[Z_AXIS] + TOOLCHANGE_PARK_ZLIFT; float raised_z = current_position[Z_AXIS] + TOOLCHANGE_PARK_ZLIFT;
#if ENABLED(max_software_endstops) #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
NOMORE(raised_z, soft_endstop_max[Z_AXIS]); NOMORE(raised_z, soft_endstop_max[Z_AXIS]);
#endif #endif
#if ENABLED(DEBUG_LEVELING_FEATURE) #if ENABLED(DEBUG_LEVELING_FEATURE)
@ -7997,7 +7940,7 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n
// record raised toolhead position for use by unpark // record raised toolhead position for use by unpark
COPY(raised_parked_position, current_position); COPY(raised_parked_position, current_position);
raised_parked_position[Z_AXIS] += TOOLCHANGE_UNPARK_ZLIFT; raised_parked_position[Z_AXIS] += TOOLCHANGE_UNPARK_ZLIFT;
#if ENABLED(max_software_endstops) #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
NOMORE(raised_parked_position[Z_AXIS], soft_endstop_max[Z_AXIS]); NOMORE(raised_parked_position[Z_AXIS], soft_endstop_max[Z_AXIS]);
#endif #endif
active_extruder_parked = true; active_extruder_parked = true;
@ -9033,18 +8976,19 @@ void ok_to_send() {
SERIAL_EOL; SERIAL_EOL;
} }
#if ENABLED(min_software_endstops) || ENABLED(max_software_endstops) #if HAS_SOFTWARE_ENDSTOPS
/** /**
* Constrain the given coordinates to the software endstops. * Constrain the given coordinates to the software endstops.
*/ */
void clamp_to_software_endstops(float target[XYZ]) { void clamp_to_software_endstops(float target[XYZ]) {
#if ENABLED(min_software_endstops) if (!soft_endstops_enabled) return;
#if ENABLED(MIN_SOFTWARE_ENDSTOPS)
NOLESS(target[X_AXIS], soft_endstop_min[X_AXIS]); NOLESS(target[X_AXIS], soft_endstop_min[X_AXIS]);
NOLESS(target[Y_AXIS], soft_endstop_min[Y_AXIS]); NOLESS(target[Y_AXIS], soft_endstop_min[Y_AXIS]);
NOLESS(target[Z_AXIS], soft_endstop_min[Z_AXIS]); NOLESS(target[Z_AXIS], soft_endstop_min[Z_AXIS]);
#endif #endif
#if ENABLED(max_software_endstops) #if ENABLED(MAX_SOFTWARE_ENDSTOPS)
NOMORE(target[X_AXIS], soft_endstop_max[X_AXIS]); NOMORE(target[X_AXIS], soft_endstop_max[X_AXIS]);
NOMORE(target[Y_AXIS], soft_endstop_max[Y_AXIS]); NOMORE(target[Y_AXIS], soft_endstop_max[Y_AXIS]);
NOMORE(target[Z_AXIS], soft_endstop_max[Z_AXIS]); NOMORE(target[Z_AXIS], soft_endstop_max[Z_AXIS]);

@ -130,6 +130,8 @@
#error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration." #error "Z_RAISE_PROBE_DEPLOY_STOW and Z_RAISE_BETWEEN_PROBINGS are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
#elif defined(Z_PROBE_DEPLOY_HEIGHT) || defined(Z_PROBE_TRAVEL_HEIGHT) #elif defined(Z_PROBE_DEPLOY_HEIGHT) || defined(Z_PROBE_TRAVEL_HEIGHT)
#error "Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration." #error "Z_PROBE_DEPLOY_HEIGHT and Z_PROBE_TRAVEL_HEIGHT are now Z_CLEARANCE_DEPLOY_PROBE and Z_CLEARANCE_BETWEEN_PROBES. Please update your configuration."
#elif defined(MESH_HOME_SEARCH_Z)
#error "MESH_HOME_SEARCH_Z is now MANUAL_PROBE_Z_RANGE. Please update your configuration."
#elif !defined(MIN_STEPS_PER_SEGMENT) #elif !defined(MIN_STEPS_PER_SEGMENT)
#error Please replace "const int dropsegments" with "#define MIN_STEPS_PER_SEGMENT" (and increase by 1) in Configuration_adv.h. #error Please replace "const int dropsegments" with "#define MIN_STEPS_PER_SEGMENT" (and increase by 1) in Configuration_adv.h.
#elif defined(PREVENT_DANGEROUS_EXTRUDE) #elif defined(PREVENT_DANGEROUS_EXTRUDE)
@ -156,6 +158,8 @@
#error "LCD_PIN_RESET is now LCD_RESET_PIN. Please update your pins definitions." #error "LCD_PIN_RESET is now LCD_RESET_PIN. Please update your pins definitions."
#elif defined(EXTRUDER_0_AUTO_FAN_PIN) || defined(EXTRUDER_1_AUTO_FAN_PIN) || defined(EXTRUDER_2_AUTO_FAN_PIN) || defined(EXTRUDER_3_AUTO_FAN_PIN) #elif defined(EXTRUDER_0_AUTO_FAN_PIN) || defined(EXTRUDER_1_AUTO_FAN_PIN) || defined(EXTRUDER_2_AUTO_FAN_PIN) || defined(EXTRUDER_3_AUTO_FAN_PIN)
#error "EXTRUDER_[0123]_AUTO_FAN_PIN is now E[0123]_AUTO_FAN_PIN. Please update your Configuration_adv.h." #error "EXTRUDER_[0123]_AUTO_FAN_PIN is now E[0123]_AUTO_FAN_PIN. Please update your Configuration_adv.h."
#elif defined(min_software_endstops) || defined(max_software_endstops)
#error "(min|max)_software_endstops are now (MIN|MAX)_SOFTWARE_ENDSTOPS. Please update your configuration."
#endif #endif
/** /**

@ -164,20 +164,13 @@ enum TempState {
}; };
#endif #endif
#if ENABLED(MESH_BED_LEVELING) #if ENABLED(PROBE_MANUALLY)
enum MeshLevelingState { enum ABLState {
MeshReport, ABLReport,
MeshStart, ABLStart,
MeshNext, ABLNext,
MeshSet, ABLSet,
MeshSetZOffset, ABLReset
MeshReset
};
enum MBLStatus {
MBL_STATUS_NONE = 0,
MBL_STATUS_HAS_MESH_BIT = 0,
MBL_STATUS_ACTIVE_BIT = 1
}; };
#endif #endif

@ -705,16 +705,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -725,6 +721,11 @@
#define Y_MAX_POS 270 #define Y_MAX_POS 270
#define Z_MAX_POS 400 #define Z_MAX_POS 400
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -750,9 +751,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -688,16 +688,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN
// :[-1, 1] // :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -708,6 +704,11 @@
#define Y_MAX_POS 205 #define Y_MAX_POS 205
#define Z_MAX_POS 235 #define Z_MAX_POS 235
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -733,9 +734,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -688,16 +688,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -708,6 +704,11 @@
#define Y_MAX_POS 205 #define Y_MAX_POS 205
#define Z_MAX_POS 235 #define Z_MAX_POS 235
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -733,9 +734,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -697,16 +697,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -717,6 +713,11 @@
#define Y_MAX_POS 210 #define Y_MAX_POS 210
#define Z_MAX_POS 180 #define Z_MAX_POS 180
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -742,9 +743,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -699,16 +699,12 @@
#define Z_HOMING_HEIGHT 5 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... #define Z_HOMING_HEIGHT 5 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -719,6 +715,11 @@
#define Y_MAX_POS 297 #define Y_MAX_POS 297
#define Z_MAX_POS 210 #define Z_MAX_POS 210
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -744,9 +745,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -734,16 +734,12 @@
#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... #define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -754,6 +750,11 @@
#define Y_MAX_POS 200 #define Y_MAX_POS 200
#define Z_MAX_POS 200 #define Z_MAX_POS 200
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -779,9 +780,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -705,16 +705,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -725,6 +721,11 @@
#define Y_MAX_POS 200 #define Y_MAX_POS 200
#define Z_MAX_POS 190 #define Z_MAX_POS 190
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -750,9 +751,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -705,16 +705,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -725,6 +721,11 @@
#define Y_MAX_POS 200 #define Y_MAX_POS 200
#define Z_MAX_POS 190 #define Z_MAX_POS 190
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -750,9 +751,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -705,16 +705,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -725,6 +721,11 @@
#define Y_MAX_POS 200 #define Y_MAX_POS 200
#define Z_MAX_POS 200 #define Z_MAX_POS 200
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -750,9 +751,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -704,16 +704,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -724,6 +720,11 @@
#define Y_MAX_POS 248 // RigidBot regular is 248mm, RigitBot Big is 304mm #define Y_MAX_POS 248 // RigidBot regular is 248mm, RigitBot Big is 304mm
#define Z_MAX_POS 254 // RigidBot regular and Big are 254mm #define Z_MAX_POS 254 // RigidBot regular and Big are 254mm
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -749,9 +750,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -720,16 +720,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR 1 #define X_HOME_DIR 1
#define Y_HOME_DIR 1 #define Y_HOME_DIR 1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -740,6 +736,11 @@
#define Y_MAX_POS 200 #define Y_MAX_POS 200
#define Z_MAX_POS 225 #define Z_MAX_POS 225
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -765,9 +766,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -726,16 +726,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -746,6 +742,11 @@
#define Y_MAX_POS 275 #define Y_MAX_POS 275
#define Z_MAX_POS 250 #define Z_MAX_POS 250
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -771,9 +772,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -697,16 +697,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR 1 #define X_HOME_DIR 1
#define Y_HOME_DIR 1 #define Y_HOME_DIR 1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -717,6 +713,11 @@
#define Y_MAX_POS 210 #define Y_MAX_POS 210
#define Z_MAX_POS 200 #define Z_MAX_POS 200
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -742,9 +743,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -705,16 +705,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -725,6 +721,11 @@
#define Y_MAX_POS 200 #define Y_MAX_POS 200
#define Z_MAX_POS 200 #define Z_MAX_POS 200
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -750,9 +751,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -807,16 +807,12 @@
#define Z_HOMING_HEIGHT 15 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... #define Z_HOMING_HEIGHT 15 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR 1 // deltas always home to max #define X_HOME_DIR 1 // deltas always home to max
#define Y_HOME_DIR 1 #define Y_HOME_DIR 1
#define Z_HOME_DIR 1 #define Z_HOME_DIR 1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -827,6 +823,11 @@
#define Y_MAX_POS DELTA_PRINTABLE_RADIUS #define Y_MAX_POS DELTA_PRINTABLE_RADIUS
#define Z_MAX_POS MANUAL_Z_HOME_POS #define Z_MAX_POS MANUAL_Z_HOME_POS
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -853,9 +854,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -791,16 +791,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR 1 // deltas always home to max #define X_HOME_DIR 1 // deltas always home to max
#define Y_HOME_DIR 1 #define Y_HOME_DIR 1
#define Z_HOME_DIR 1 #define Z_HOME_DIR 1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -811,6 +807,11 @@
#define Y_MAX_POS DELTA_PRINTABLE_RADIUS #define Y_MAX_POS DELTA_PRINTABLE_RADIUS
#define Z_MAX_POS MANUAL_Z_HOME_POS #define Z_MAX_POS MANUAL_Z_HOME_POS
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -836,9 +837,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -794,16 +794,12 @@
//#define Z_HOMING_HEIGHT 15 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 15 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR 1 // deltas always home to max #define X_HOME_DIR 1 // deltas always home to max
#define Y_HOME_DIR 1 #define Y_HOME_DIR 1
#define Z_HOME_DIR 1 #define Z_HOME_DIR 1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -814,6 +810,11 @@
#define Y_MAX_POS DELTA_PRINTABLE_RADIUS #define Y_MAX_POS DELTA_PRINTABLE_RADIUS
#define Z_MAX_POS MANUAL_Z_HOME_POS #define Z_MAX_POS MANUAL_Z_HOME_POS
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -839,9 +840,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -793,16 +793,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR 1 // deltas always home to max #define X_HOME_DIR 1 // deltas always home to max
#define Y_HOME_DIR 1 #define Y_HOME_DIR 1
#define Z_HOME_DIR 1 #define Z_HOME_DIR 1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -813,6 +809,11 @@
#define Y_MAX_POS DELTA_PRINTABLE_RADIUS #define Y_MAX_POS DELTA_PRINTABLE_RADIUS
#define Z_MAX_POS MANUAL_Z_HOME_POS #define Z_MAX_POS MANUAL_Z_HOME_POS
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -838,9 +839,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -797,16 +797,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR 1 // deltas always home to max #define X_HOME_DIR 1 // deltas always home to max
#define Y_HOME_DIR 1 #define Y_HOME_DIR 1
#define Z_HOME_DIR 1 #define Z_HOME_DIR 1
#define min_software_endstops false // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -817,6 +813,11 @@
#define Y_MAX_POS DELTA_PRINTABLE_RADIUS #define Y_MAX_POS DELTA_PRINTABLE_RADIUS
#define Z_MAX_POS MANUAL_Z_HOME_POS #define Z_MAX_POS MANUAL_Z_HOME_POS
// If enabled, axes won't move below MIN_POS in response to movement commands.
//#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -842,9 +843,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -708,16 +708,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -728,6 +724,11 @@
#define Y_MAX_POS 150 #define Y_MAX_POS 150
#define Z_MAX_POS 86 #define Z_MAX_POS 86
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -753,9 +754,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -701,16 +701,12 @@
//#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ... //#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
// Be sure you have this distance over your Z_MAX_POS in case. // Be sure you have this distance over your Z_MAX_POS in case.
// ENDSTOP SETTINGS: // Direction of endstops when homing; 1=MAX, -1=MIN
// Sets direction of endstops when homing; 1=MAX, -1=MIN // :[-1,1]
// :[-1, 1]
#define X_HOME_DIR -1 #define X_HOME_DIR -1
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops true // If true, axis won't move to coordinates less than HOME_POS.
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// @section machine // @section machine
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
@ -721,6 +717,11 @@
#define Y_MAX_POS 205 #define Y_MAX_POS 205
#define Z_MAX_POS 120 #define Z_MAX_POS 120
// If enabled, axes won't move below MIN_POS in response to movement commands.
#define MIN_SOFTWARE_ENDSTOPS
// If enabled, axes won't move above MAX_POS in response to movement commands.
#define MAX_SOFTWARE_ENDSTOPS
/** /**
* Filament Runout Sensor * Filament Runout Sensor
* A mechanical or opto endstop is used to check for the presence of filament. * A mechanical or opto endstop is used to check for the presence of filament.
@ -746,9 +747,9 @@
#define MESH_INSET 10 // Mesh inset margin on print area #define MESH_INSET 10 // Mesh inset margin on print area
#define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited. #define MESH_NUM_X_POINTS 3 // Don't use more than 7 points per axis, implementation limited.
#define MESH_NUM_Y_POINTS 3 #define MESH_NUM_Y_POINTS 3
#define MESH_HOME_SEARCH_Z 4 // Z after Home, bed somewhere below but above 0.0. #define MANUAL_PROBE_Z_RANGE 4 // Z Range centered on Z_MIN_POS for LCD Z adjustment
//#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest at origin [0,0,0] //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
//#define MANUAL_BED_LEVELING // Add display menu option for bed leveling. //#define MANUAL_BED_LEVELING // Add display menu option for bed leveling.

@ -23,6 +23,23 @@
#include "Marlin.h" #include "Marlin.h"
#if ENABLED(MESH_BED_LEVELING) #if ENABLED(MESH_BED_LEVELING)
enum MeshLevelingState {
MeshReport,
MeshStart,
MeshNext,
MeshSet,
MeshSetZOffset,
MeshReset
};
enum MBLStatus {
MBL_STATUS_NONE = 0,
MBL_STATUS_HAS_MESH_BIT = 0,
MBL_STATUS_ACTIVE_BIT = 1,
MBL_STATUS_REACTIVATE_BIT = 2
};
#define MESH_X_DIST ((MESH_MAX_X - (MESH_MIN_X))/(MESH_NUM_X_POINTS - 1)) #define MESH_X_DIST ((MESH_MAX_X - (MESH_MIN_X))/(MESH_NUM_X_POINTS - 1))
#define MESH_Y_DIST ((MESH_MAX_Y - (MESH_MIN_Y))/(MESH_NUM_Y_POINTS - 1)) #define MESH_Y_DIST ((MESH_MAX_Y - (MESH_MIN_Y))/(MESH_NUM_Y_POINTS - 1))
@ -44,6 +61,8 @@
void set_active(const bool onOff) { onOff ? SBI(status, MBL_STATUS_ACTIVE_BIT) : CBI(status, MBL_STATUS_ACTIVE_BIT); } void set_active(const bool onOff) { onOff ? SBI(status, MBL_STATUS_ACTIVE_BIT) : CBI(status, MBL_STATUS_ACTIVE_BIT); }
bool has_mesh() const { return TEST(status, MBL_STATUS_HAS_MESH_BIT); } bool has_mesh() const { return TEST(status, MBL_STATUS_HAS_MESH_BIT); }
void set_has_mesh(const bool onOff) { onOff ? SBI(status, MBL_STATUS_HAS_MESH_BIT) : CBI(status, MBL_STATUS_HAS_MESH_BIT); } void set_has_mesh(const bool onOff) { onOff ? SBI(status, MBL_STATUS_HAS_MESH_BIT) : CBI(status, MBL_STATUS_HAS_MESH_BIT); }
bool reactivate() { bool b = TEST(status, MBL_STATUS_REACTIVATE_BIT); CBI(status, MBL_STATUS_REACTIVATE_BIT); return b; }
void set_reactivate(const bool onOff) { onOff ? SBI(status, MBL_STATUS_REACTIVATE_BIT) : CBI(status, MBL_STATUS_REACTIVATE_BIT); }
inline void zigzag(const int8_t index, int8_t &px, int8_t &py) const { inline void zigzag(const int8_t index, int8_t &px, int8_t &py) const {
px = index % (MESH_NUM_X_POINTS); px = index % (MESH_NUM_X_POINTS);

@ -1220,21 +1220,20 @@ void kill_screen(const char* lcd_msg) {
* *
*/ */
static uint8_t _lcd_level_bed_position; static uint8_t manual_probe_index;
// Utility to go to the next mesh point // Utility to go to the next mesh point
// A raise is added between points if Z_HOMING_HEIGHT is in use inline void _manual_probe_xy(float x, float y) {
// Note: During Manual Bed Leveling the homed Z position is MESH_HOME_SEARCH_Z
// Z position will be restored with the final action, a G28
inline void _mbl_goto_xy(float x, float y) {
if (no_reentrance) return; if (no_reentrance) return;
current_position[Z_AXIS] = LOGICAL_Z_POSITION(MESH_HOME_SEARCH_Z + Z_HOMING_HEIGHT); #if MANUAL_PROBE_HEIGHT > 0
line_to_current(Z_AXIS); current_position[Z_AXIS] = LOGICAL_Z_POSITION(Z_MIN_POS) + MANUAL_PROBE_HEIGHT;
line_to_current(Z_AXIS);
#endif
current_position[X_AXIS] = LOGICAL_X_POSITION(x); current_position[X_AXIS] = LOGICAL_X_POSITION(x);
current_position[Y_AXIS] = LOGICAL_Y_POSITION(y); current_position[Y_AXIS] = LOGICAL_Y_POSITION(y);
planner.buffer_line_kinematic(current_position, MMM_TO_MMS(XY_PROBE_SPEED), active_extruder); planner.buffer_line_kinematic(current_position, MMM_TO_MMS(XY_PROBE_SPEED), active_extruder);
#if Z_HOMING_HEIGHT > 0 #if MANUAL_PROBE_HEIGHT > 0
current_position[Z_AXIS] = LOGICAL_Z_POSITION(MESH_HOME_SEARCH_Z); current_position[Z_AXIS] = LOGICAL_Z_POSITION(Z_MIN_POS) + 0.2;
line_to_current(Z_AXIS); line_to_current(Z_AXIS);
#endif #endif
lcd_synchronize(); lcd_synchronize();
@ -1259,48 +1258,44 @@ void kill_screen(const char* lcd_msg) {
if (encoderPosition) { if (encoderPosition) {
refresh_cmd_timeout(); refresh_cmd_timeout();
current_position[Z_AXIS] += float((int32_t)encoderPosition) * (MBL_Z_STEP); current_position[Z_AXIS] += float((int32_t)encoderPosition) * (MBL_Z_STEP);
NOLESS(current_position[Z_AXIS], 0); NOLESS(current_position[Z_AXIS], -(MANUAL_PROBE_Z_RANGE) * 0.5);
NOMORE(current_position[Z_AXIS], MESH_HOME_SEARCH_Z * 2); NOMORE(current_position[Z_AXIS], (MANUAL_PROBE_Z_RANGE) * 0.5);
line_to_current(Z_AXIS); line_to_current(Z_AXIS);
lcdDrawUpdate = LCDVIEW_KEEP_REDRAWING; lcdDrawUpdate = LCDVIEW_KEEP_REDRAWING;
encoderPosition = 0; encoderPosition = 0;
} }
static bool debounce_click = false;
if (lcd_clicked) { if (lcd_clicked) {
if (!debounce_click) { mbl.set_zigzag_z(manual_probe_index++, current_position[Z_AXIS]);
debounce_click = true; // ignore multiple "clicks" in a row if (manual_probe_index == (MESH_NUM_X_POINTS) * (MESH_NUM_Y_POINTS)) {
mbl.set_zigzag_z(_lcd_level_bed_position++, current_position[Z_AXIS]); lcd_goto_screen(_lcd_level_bed_done);
if (_lcd_level_bed_position == (MESH_NUM_X_POINTS) * (MESH_NUM_Y_POINTS)) {
lcd_goto_screen(_lcd_level_bed_done);
current_position[Z_AXIS] = MESH_HOME_SEARCH_Z + Z_HOMING_HEIGHT; #if MANUAL_PROBE_HEIGHT > 0
current_position[Z_AXIS] = LOGICAL_Z_POSITION(Z_MIN_POS) + MANUAL_PROBE_HEIGHT;
line_to_current(Z_AXIS); line_to_current(Z_AXIS);
lcd_synchronize(); lcd_synchronize();
#endif
mbl.set_has_mesh(true); mbl.set_has_mesh(true);
enqueue_and_echo_commands_P(PSTR("G28")); mbl.set_reactivate(true);
lcd_return_to_status(); enqueue_and_echo_commands_P(PSTR("G28"));
//LCD_MESSAGEPGM(MSG_LEVEL_BED_DONE); lcd_return_to_status();
#if HAS_BUZZER //LCD_MESSAGEPGM(MSG_LEVEL_BED_DONE);
lcd_buzz(200, 659); #if HAS_BUZZER
lcd_buzz(200, 698); lcd_buzz(200, 659);
#endif lcd_buzz(200, 698);
} #endif
else { }
lcd_goto_screen(_lcd_level_goto_next_point); else {
} lcd_goto_screen(_lcd_level_goto_next_point);
} }
}
else {
debounce_click = false;
} }
KeepDrawing: KeepDrawing:
// Update on first display, then only on updates to Z position // Update on first display, then only on updates to Z position
// Show message above on clicks instead // Show message above on clicks instead
if (lcdDrawUpdate) { if (lcdDrawUpdate) {
float v = current_position[Z_AXIS] - MESH_HOME_SEARCH_Z; const float v = current_position[Z_AXIS];
lcd_implementation_drawedit(PSTR(MSG_MOVE_Z), ftostr43sign(v + (v < 0 ? -0.0001 : 0.0001), '+')); lcd_implementation_drawedit(PSTR(MSG_MOVE_Z), ftostr43sign(v + (v < 0 ? -0.0001 : 0.0001), '+'));
} }
@ -1312,7 +1307,7 @@ KeepDrawing:
void _lcd_level_bed_moving() { void _lcd_level_bed_moving() {
if (lcdDrawUpdate) { if (lcdDrawUpdate) {
char msg[10]; char msg[10];
sprintf_P(msg, PSTR("%i / %u"), (int)(_lcd_level_bed_position + 1), (MESH_NUM_X_POINTS) * (MESH_NUM_Y_POINTS)); sprintf_P(msg, PSTR("%i / %u"), (int)(manual_probe_index + 1), (MESH_NUM_X_POINTS) * (MESH_NUM_Y_POINTS));
lcd_implementation_drawedit(PSTR(MSG_LEVEL_BED_NEXT_POINT), msg); lcd_implementation_drawedit(PSTR(MSG_LEVEL_BED_NEXT_POINT), msg);
} }
@ -1326,10 +1321,10 @@ KeepDrawing:
// Set the menu to display ahead of blocking call // Set the menu to display ahead of blocking call
lcd_goto_screen(_lcd_level_bed_moving); lcd_goto_screen(_lcd_level_bed_moving);
// _mbl_goto_xy runs the menu loop until the move is done // _manual_probe_xy runs the menu loop until the move is done
int8_t px, py; int8_t px, py;
mbl.zigzag(_lcd_level_bed_position, px, py); mbl.zigzag(manual_probe_index, px, py);
_mbl_goto_xy(mbl.get_probe_x(px), mbl.get_probe_y(py)); _manual_probe_xy(mbl.get_probe_x(px), mbl.get_probe_y(py));
// After the blocking function returns, change menus // After the blocking function returns, change menus
lcd_goto_screen(_lcd_level_bed_get_z); lcd_goto_screen(_lcd_level_bed_get_z);
@ -1342,13 +1337,7 @@ KeepDrawing:
void _lcd_level_bed_homing_done() { void _lcd_level_bed_homing_done() {
if (lcdDrawUpdate) lcd_implementation_drawedit(PSTR(MSG_LEVEL_BED_WAITING)); if (lcdDrawUpdate) lcd_implementation_drawedit(PSTR(MSG_LEVEL_BED_WAITING));
if (lcd_clicked) { if (lcd_clicked) {
_lcd_level_bed_position = 0; manual_probe_index = 0;
current_position[Z_AXIS] = MESH_HOME_SEARCH_Z
#if Z_HOME_DIR > 0
+ Z_MAX_POS
#endif
;
planner.set_position_mm(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
lcd_goto_screen(_lcd_level_goto_next_point); lcd_goto_screen(_lcd_level_goto_next_point);
} }
} }
@ -1607,9 +1596,20 @@ KeepDrawing:
if (encoderPosition) { if (encoderPosition) {
refresh_cmd_timeout(); refresh_cmd_timeout();
// Limit to software endstops, if enabled float min = current_position[axis] - 1000,
float min = (soft_endstops_enabled && min_software_endstops) ? soft_endstop_min[axis] : current_position[axis] - 1000, max = current_position[axis] + 1000;
max = (soft_endstops_enabled && max_software_endstops) ? soft_endstop_max[axis] : current_position[axis] + 1000;
#if HAS_SOFTWARE_ENDSTOPS
// Limit to software endstops, if enabled
if (soft_endstops_enabled) {
#if ENABLED(MIN_SOFTWARE_ENDSTOPS)
min = soft_endstop_min[axis];
#endif
#if ENABLED(MAX_SOFTWARE_ENDSTOPS)
max = soft_endstop_max[axis];
#endif
}
#endif
// Get the new position // Get the new position
current_position[axis] += float((int32_t)encoderPosition) * move_menu_scale; current_position[axis] += float((int32_t)encoderPosition) * move_menu_scale;

Loading…
Cancel
Save