|
|
|
|
@ -1404,13 +1404,20 @@ void lcd_quick_feedback(const bool clear_buttons) {
|
|
|
|
|
//
|
|
|
|
|
MENU_ITEM_EDIT(int3, MSG_SPEED, &feedrate_percentage, 10, 999);
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Manual bed leveling, Bed Z:
|
|
|
|
|
//
|
|
|
|
|
#if ENABLED(MESH_BED_LEVELING) && ENABLED(LCD_BED_LEVELING)
|
|
|
|
|
MENU_ITEM_EDIT(float43, MSG_BED_Z, &mbl.z_offset, -1, 1);
|
|
|
|
|
#endif
|
|
|
|
|
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Leveling Fade Height
|
|
|
|
|
//
|
|
|
|
|
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT) && DISABLED(SLIM_LCD_MENUS)
|
|
|
|
|
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(float62, MSG_Z_FADE_HEIGHT, &new_z_fade_height, 0.0, 100.0, _lcd_set_z_fade_height);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// Nozzle:
|
|
|
|
|
// Nozzle [1-4]:
|
|
|
|
|
@ -1883,7 +1890,7 @@ void lcd_quick_feedback(const bool clear_buttons) {
|
|
|
|
|
|
|
|
|
|
#endif // LEVEL_BED_CORNERS
|
|
|
|
|
|
|
|
|
|
#if ENABLED(LCD_BED_LEVELING)
|
|
|
|
|
#if ENABLED(LCD_BED_LEVELING) && (ENABLED(PROBE_MANUALLY) || ENABLED(MESH_BED_LEVELING))
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
*
|
|
|
|
|
@ -2045,76 +2052,6 @@ void lcd_quick_feedback(const bool clear_buttons) {
|
|
|
|
|
enqueue_and_echo_commands_P(PSTR("G28"));
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
static bool new_level_state;
|
|
|
|
|
void _lcd_toggle_bed_leveling() { set_bed_leveling_enabled(new_level_state); }
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
* Step 1: Bed Level entry-point
|
|
|
|
|
*
|
|
|
|
|
* << Prepare
|
|
|
|
|
* Auto Home (if homing needed)
|
|
|
|
|
* Leveling On/Off (if data exists, and homed)
|
|
|
|
|
* Fade Height: --- (Req: ENABLE_LEVELING_FADE_HEIGHT)
|
|
|
|
|
* Mesh Z Offset: --- (Req: MESH_BED_LEVELING)
|
|
|
|
|
* Z Probe Offset: --- (Req: HAS_BED_PROBE, Opt: BABYSTEP_ZPROBE_OFFSET)
|
|
|
|
|
* Level Bed >
|
|
|
|
|
* Level Corners > (if homed)
|
|
|
|
|
* Load Settings (Req: EEPROM_SETTINGS)
|
|
|
|
|
* Save Settings (Req: EEPROM_SETTINGS)
|
|
|
|
|
*/
|
|
|
|
|
void lcd_bed_leveling() {
|
|
|
|
|
START_MENU();
|
|
|
|
|
MENU_BACK(MSG_PREPARE);
|
|
|
|
|
|
|
|
|
|
#if DISABLED(MESH_BED_LEVELING)
|
|
|
|
|
if (!(axis_known_position[X_AXIS] && axis_known_position[Y_AXIS] && axis_known_position[Z_AXIS]))
|
|
|
|
|
MENU_ITEM(gcode, MSG_AUTO_HOME, PSTR("G28"));
|
|
|
|
|
else
|
|
|
|
|
#endif
|
|
|
|
|
if (leveling_is_valid()) {
|
|
|
|
|
new_level_state = planner.leveling_active;
|
|
|
|
|
MENU_ITEM_EDIT_CALLBACK(bool, MSG_BED_LEVELING, &new_level_state, _lcd_toggle_bed_leveling);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
|
|
|
|
|
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(float62, MSG_Z_FADE_HEIGHT, &new_z_fade_height, 0.0, 100.0, _lcd_set_z_fade_height);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// MBL Z Offset
|
|
|
|
|
//
|
|
|
|
|
#if ENABLED(MESH_BED_LEVELING)
|
|
|
|
|
MENU_ITEM_EDIT(float43, MSG_BED_Z, &mbl.z_offset, -1, 1);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
|
|
|
|
|
MENU_ITEM(submenu, MSG_ZPROBE_ZOFFSET, lcd_babystep_zoffset);
|
|
|
|
|
#elif HAS_BED_PROBE
|
|
|
|
|
MENU_ITEM_EDIT(float52, MSG_ZPROBE_ZOFFSET, &zprobe_zoffset, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
MENU_ITEM(submenu, MSG_LEVEL_BED, _lcd_level_bed_continue);
|
|
|
|
|
|
|
|
|
|
#if ENABLED(LEVEL_BED_CORNERS)
|
|
|
|
|
// Move to the next corner for leveling
|
|
|
|
|
if (axis_homed[X_AXIS] && axis_homed[Y_AXIS] && axis_homed[Z_AXIS])
|
|
|
|
|
MENU_ITEM(submenu, MSG_LEVEL_CORNERS, _lcd_level_bed_corners);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if ENABLED(EEPROM_SETTINGS)
|
|
|
|
|
MENU_ITEM(function, MSG_LOAD_EEPROM, lcd_load_settings);
|
|
|
|
|
MENU_ITEM(function, MSG_STORE_EEPROM, lcd_store_settings);
|
|
|
|
|
#endif
|
|
|
|
|
END_MENU();
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
|
|
|
|
|
void _lcd_goto_bed_leveling() {
|
|
|
|
|
lcd_goto_screen(lcd_bed_leveling);
|
|
|
|
|
new_z_fade_height = planner.z_fade_height;
|
|
|
|
|
}
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#elif ENABLED(AUTO_BED_LEVELING_UBL)
|
|
|
|
|
|
|
|
|
|
void _lcd_ubl_level_bed();
|
|
|
|
|
@ -2647,6 +2584,93 @@ void lcd_quick_feedback(const bool clear_buttons) {
|
|
|
|
|
|
|
|
|
|
#endif // AUTO_BED_LEVELING_UBL
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
#if ENABLED(LCD_BED_LEVELING) || (PLANNER_LEVELING && DISABLED(SLIM_LCD_MENUS))
|
|
|
|
|
void _lcd_toggle_bed_leveling() { set_bed_leveling_enabled(!planner.leveling_active); }
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if ENABLED(LCD_BED_LEVELING)
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
* Step 1: Bed Level entry-point
|
|
|
|
|
*
|
|
|
|
|
* << Prepare
|
|
|
|
|
* Auto Home (if homing needed)
|
|
|
|
|
* Leveling On/Off (if data exists, and homed)
|
|
|
|
|
* Fade Height: --- (Req: ENABLE_LEVELING_FADE_HEIGHT)
|
|
|
|
|
* Mesh Z Offset: --- (Req: MESH_BED_LEVELING)
|
|
|
|
|
* Z Probe Offset: --- (Req: HAS_BED_PROBE, Opt: BABYSTEP_ZPROBE_OFFSET)
|
|
|
|
|
* Level Bed >
|
|
|
|
|
* Level Corners > (if homed)
|
|
|
|
|
* Load Settings (Req: EEPROM_SETTINGS)
|
|
|
|
|
* Save Settings (Req: EEPROM_SETTINGS)
|
|
|
|
|
*/
|
|
|
|
|
void lcd_bed_leveling() {
|
|
|
|
|
START_MENU();
|
|
|
|
|
MENU_BACK(MSG_PREPARE);
|
|
|
|
|
|
|
|
|
|
const bool is_homed = axis_known_position[X_AXIS] && axis_known_position[Y_AXIS] && axis_known_position[Z_AXIS];
|
|
|
|
|
|
|
|
|
|
// Auto Home if not using manual probing
|
|
|
|
|
#if DISABLED(PROBE_MANUALLY) && DISABLED(MESH_BED_LEVELING)
|
|
|
|
|
if (!is_homed) MENU_ITEM(gcode, MSG_AUTO_HOME, PSTR("G28"));
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
// Level Bed
|
|
|
|
|
#if ENABLED(PROBE_MANUALLY) || ENABLED(MESH_BED_LEVELING)
|
|
|
|
|
// Manual leveling uses a guided procedure
|
|
|
|
|
MENU_ITEM(submenu, MSG_LEVEL_BED, _lcd_level_bed_continue);
|
|
|
|
|
#else
|
|
|
|
|
// Automatic leveling can just run the G-code
|
|
|
|
|
MENU_ITEM(gcode, MSG_LEVEL_BED, is_homed ? PSTR("G29") : PSTR("G28\nG29"));
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
// Homed and leveling is valid? Then leveling can be toggled.
|
|
|
|
|
if (is_homed && leveling_is_valid()) {
|
|
|
|
|
bool new_level_state = planner.leveling_active;
|
|
|
|
|
MENU_ITEM_EDIT_CALLBACK(bool, MSG_BED_LEVELING, &new_level_state, _lcd_toggle_bed_leveling);
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
// Z Fade Height
|
|
|
|
|
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
|
|
|
|
|
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(float62, MSG_Z_FADE_HEIGHT, &new_z_fade_height, 0.0, 100.0, _lcd_set_z_fade_height);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
//
|
|
|
|
|
// MBL Z Offset
|
|
|
|
|
//
|
|
|
|
|
#if ENABLED(MESH_BED_LEVELING)
|
|
|
|
|
MENU_ITEM_EDIT(float43, MSG_BED_Z, &mbl.z_offset, -1, 1);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
|
|
|
|
|
MENU_ITEM(submenu, MSG_ZPROBE_ZOFFSET, lcd_babystep_zoffset);
|
|
|
|
|
#elif HAS_BED_PROBE
|
|
|
|
|
MENU_ITEM_EDIT(float52, MSG_ZPROBE_ZOFFSET, &zprobe_zoffset, Z_PROBE_OFFSET_RANGE_MIN, Z_PROBE_OFFSET_RANGE_MAX);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if ENABLED(LEVEL_BED_CORNERS)
|
|
|
|
|
// Move to the next corner for leveling
|
|
|
|
|
if (axis_homed[X_AXIS] && axis_homed[Y_AXIS] && axis_homed[Z_AXIS])
|
|
|
|
|
MENU_ITEM(submenu, MSG_LEVEL_CORNERS, _lcd_level_bed_corners);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if ENABLED(EEPROM_SETTINGS)
|
|
|
|
|
MENU_ITEM(function, MSG_LOAD_EEPROM, lcd_load_settings);
|
|
|
|
|
MENU_ITEM(function, MSG_STORE_EEPROM, lcd_store_settings);
|
|
|
|
|
#endif
|
|
|
|
|
END_MENU();
|
|
|
|
|
}
|
|
|
|
|
|
|
|
|
|
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
|
|
|
|
|
void _lcd_goto_bed_leveling() {
|
|
|
|
|
lcd_goto_screen(lcd_bed_leveling);
|
|
|
|
|
new_z_fade_height = planner.z_fade_height;
|
|
|
|
|
}
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#endif // LCD_BED_LEVELING
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
*
|
|
|
|
|
* "Prepare" submenu
|
|
|
|
|
@ -2683,26 +2707,44 @@ void lcd_quick_feedback(const bool clear_buttons) {
|
|
|
|
|
// Level Bed
|
|
|
|
|
//
|
|
|
|
|
#if ENABLED(AUTO_BED_LEVELING_UBL)
|
|
|
|
|
MENU_ITEM(submenu, MSG_UBL_LEVEL_BED,
|
|
|
|
|
|
|
|
|
|
MENU_ITEM(submenu, MSG_UBL_LEVEL_BED, (
|
|
|
|
|
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
|
|
|
|
|
_lcd_goto_ubl_level_bed
|
|
|
|
|
#else
|
|
|
|
|
_lcd_ubl_level_bed
|
|
|
|
|
#endif
|
|
|
|
|
)
|
|
|
|
|
);
|
|
|
|
|
|
|
|
|
|
#elif ENABLED(LCD_BED_LEVELING)
|
|
|
|
|
|
|
|
|
|
#if ENABLED(PROBE_MANUALLY)
|
|
|
|
|
if (!g29_in_progress)
|
|
|
|
|
#endif
|
|
|
|
|
MENU_ITEM(submenu, MSG_BED_LEVELING,
|
|
|
|
|
|
|
|
|
|
MENU_ITEM(submenu, MSG_BED_LEVELING, (
|
|
|
|
|
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
|
|
|
|
|
_lcd_goto_bed_leveling
|
|
|
|
|
#else
|
|
|
|
|
lcd_bed_leveling
|
|
|
|
|
#endif
|
|
|
|
|
)
|
|
|
|
|
);
|
|
|
|
|
#elif PLANNER_LEVELING && DISABLED(PROBE_MANUALLY) && DISABLED(SLIM_LCD_MENUS)
|
|
|
|
|
MENU_ITEM(gcode, MSG_BED_LEVELING, PSTR("G28\nG29"));
|
|
|
|
|
|
|
|
|
|
#elif PLANNER_LEVELING && DISABLED(SLIM_LCD_MENUS)
|
|
|
|
|
|
|
|
|
|
#if DISABLED(PROBE_MANUALLY)
|
|
|
|
|
MENU_ITEM(gcode, MSG_LEVEL_BED, PSTR("G28\nG29"));
|
|
|
|
|
#endif
|
|
|
|
|
if (leveling_is_valid()) {
|
|
|
|
|
bool new_level_state = planner.leveling_active;
|
|
|
|
|
MENU_ITEM_EDIT_CALLBACK(bool, MSG_BED_LEVELING, &new_level_state, _lcd_toggle_bed_leveling);
|
|
|
|
|
}
|
|
|
|
|
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
|
|
|
|
|
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(float62, MSG_Z_FADE_HEIGHT, &new_z_fade_height, 0.0, 100.0, _lcd_set_z_fade_height);
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
#if ENABLED(LEVEL_BED_CORNERS) && DISABLED(LCD_BED_LEVELING)
|
|
|
|
|
|
Scott Lahteine
7 years ago