Update copyright in header, etc. (#14645)

2.0.x
Ludy 6 years ago committed by Scott Lahteine
parent 5535a047d7
commit abc9b52692

@ -260,7 +260,7 @@
#define RGB_LED_B_PIN P1_22 // J8-2 (LCD_D7 on Fysetc schematic) #define RGB_LED_B_PIN P1_22 // J8-2 (LCD_D7 on Fysetc schematic)
#endif #endif
#elif ENABLED(FYSETC_MINI_12864_2_1) #elif ENABLED(FYSETC_MINI_12864_2_1)
#define NEOPIXEL_PIN P2_12 #define NEOPIXEL_PIN P2_12
#endif #endif
#elif ENABLED(MINIPANEL) #elif ENABLED(MINIPANEL)
@ -304,9 +304,14 @@
#endif #endif
#if MB(MKS_SBASE) && HAS_TMC220x #if MB(MKS_SBASE) && HAS_TMC220x
// The shortage of pins becomes apparent.
// Worst case you may have to give up the LCD /**
// RX pins need to be interrupt capable * TMC2208/TMC2209 stepper drivers
*
* The shortage of pins becomes apparent.
* Worst case you may have to give up the LCD
* RX pins need to be interrupt capable
*/
#define X_SERIAL_TX_PIN P1_22 // J8-2 #define X_SERIAL_TX_PIN P1_22 // J8-2
#define X_SERIAL_RX_PIN P2_12 // J8-4 Interrupt Capable #define X_SERIAL_RX_PIN P2_12 // J8-4 Interrupt Capable
#define Y_SERIAL_TX_PIN P1_23 // J8-3 #define Y_SERIAL_TX_PIN P1_23 // J8-3
@ -344,26 +349,26 @@
* PWM1.6 P2_05 RAMPS_D10_PIN * PWM1.6 P2_05 RAMPS_D10_PIN
*/ */
/** /**
* Special pins * Special pins
* P1_30 - not 5V tolerant - EXP1 * P1_30 - not 5V tolerant - EXP1
* P1_31 - not 5V tolerant - EXP1 * P1_31 - not 5V tolerant - EXP1
* P0_27 - open collector - EXP2 * P0_27 - open collector - EXP2
* P0_28 - open collector - EXP2 * P0_28 - open collector - EXP2
* *
*/ */
/** /**
* Serial Ports * Serial Ports
* P0_00 - Port 3 * P0_00 - Port 3
* P0_01 - SD Card (Onboard) * P0_01 - SD Card (Onboard)
* P0_10 - Port 2 * P0_10 - Port 2
* P0_11 - Y_EN/Y_DIR * P0_11 - Y_EN/Y_DIR
* P0_15 - Port 1 * P0_15 - Port 1
* P0_16 - EXP1 * P0_16 - EXP1
* P0_02 - Port 0 * P0_02 - Port 0
* P0_03 - AUX1 * P0_03 - AUX1
* P0_29 - Port -1 * P0_29 - Port -1
* P0_30 - USB * P0_30 - USB
* *
*/ */

@ -110,7 +110,7 @@
#if HAS_TMC220x #if HAS_TMC220x
/** /**
* TMC2208 stepper drivers * TMC2208/TMC2209 stepper drivers
* *
* Hardware serial communication ports. * Hardware serial communication ports.
* If undefined software serial is used according to the pins below * If undefined software serial is used according to the pins below

@ -121,24 +121,24 @@
* If undefined software serial is used according to the pins below * If undefined software serial is used according to the pins below
*/ */
/** //
* Software serial // Software serial
*/ //
// P2_08 E1-Step // P2_08 E1-Step
// P2_13 E1-Dir // P2_13 E1-Dir
#define X_SERIAL_TX_PIN P2_13 #define X_SERIAL_TX_PIN P2_13
#define X_SERIAL_RX_PIN P2_13 #define X_SERIAL_RX_PIN P2_13
#define Y_SERIAL_TX_PIN P0_00 #define Y_SERIAL_TX_PIN P0_00
#define Y_SERIAL_RX_PIN P0_00 #define Y_SERIAL_RX_PIN P0_00
#define Z_SERIAL_TX_PIN P0_01 #define Z_SERIAL_TX_PIN P0_01
#define Z_SERIAL_RX_PIN P0_01 #define Z_SERIAL_RX_PIN P0_01
#define E0_SERIAL_TX_PIN P2_08 #define E0_SERIAL_TX_PIN P2_08
#define E0_SERIAL_RX_PIN P2_08 #define E0_SERIAL_RX_PIN P2_08
#endif #endif
@ -254,9 +254,9 @@
#error "LASER_FEATURE requires 3 free servo pins." #error "LASER_FEATURE requires 3 free servo pins."
#endif #endif
#endif #endif
#define SPINDLE_LASER_ENA_PIN SERVO1_PIN // (6) Pin should have a pullup/pulldown! #define SPINDLE_LASER_ENA_PIN SERVO1_PIN // (6) Pin should have a pullup/pulldown!
#define SPINDLE_LASER_PWM_PIN SERVO3_PIN // (4) MUST BE HARDWARE PWM #define SPINDLE_LASER_PWM_PIN SERVO3_PIN // (4) MUST BE HARDWARE PWM
#define SPINDLE_DIR_PIN SERVO2_PIN // (5) #define SPINDLE_DIR_PIN SERVO2_PIN // (5)
#endif #endif
// //
@ -309,10 +309,10 @@
#elif HAS_SPI_LCD #elif HAS_SPI_LCD
//#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3 //#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3
//#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3 //#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3
//#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3 //#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3
//#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS) //#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS)
#if ENABLED(FYSETC_MINI_12864) #if ENABLED(FYSETC_MINI_12864)
#define BEEPER_PIN P1_01 #define BEEPER_PIN P1_01
@ -337,10 +337,10 @@
#define SHIFT_LD P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant) #define SHIFT_LD P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant)
#endif #endif
#else #else
//#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4 //#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4
//#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4 //#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4
//#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4 //#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4
//#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4 //#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4
#endif #endif
#if ANY(VIKI2, miniVIKI) #if ANY(VIKI2, miniVIKI)
@ -365,7 +365,7 @@
//#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
// results in LCD soft SPI mode 3, SD soft SPI mode 0 // results in LCD soft SPI mode 3, SD soft SPI mode 0
#define LCD_RESET_PIN P0_16 // Must be high or open for LCD to operate normally. #define LCD_RESET_PIN P0_16 // Must be high or open for LCD to operate normally.
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
#ifndef RGB_LED_R_PIN #ifndef RGB_LED_R_PIN
@ -378,7 +378,7 @@
#define RGB_LED_B_PIN P1_08 #define RGB_LED_B_PIN P1_08
#endif #endif
#elif ENABLED(FYSETC_MINI_12864_2_1) #elif ENABLED(FYSETC_MINI_12864_2_1)
#define NEOPIXEL_PIN P1_00 #define NEOPIXEL_PIN P1_00
#endif #endif
#else #else
#define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2 #define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2

@ -40,13 +40,17 @@
//#undef BTN_EN1 //#undef BTN_EN1
//#undef BTN_EN2 //#undef BTN_EN2
//#define BTN_EN1 P1_23 // EXP2.5 //#define BTN_EN1 P1_23 // EXP2.5
//#define BTN_EN2 P1_22 // EXP2.3 //#define BTN_EN2 P1_22 // EXP2.3
#if HAS_TMC220x #if HAS_TMC220x
// The shortage of pins becomes apparent. /**
// In the worst case you may have to give up the LCD. * TMC2208/TMC2209 stepper drivers
// RX pins must be interrupt-capable. *
* The shortage of pins becomes apparent.
* In the worst case you may have to give up the LCD.
* RX pins must be interrupt-capable.
*/
#define X_SERIAL_TX_PIN P4_29 // J8-2 #define X_SERIAL_TX_PIN P4_29 // J8-2
#define X_SERIAL_RX_PIN P4_29 // J8-2 #define X_SERIAL_RX_PIN P4_29 // J8-2

@ -118,8 +118,12 @@
// //
#if HAS_TMC220x #if HAS_TMC220x
// Software serial /**
// At the moment, F6 rx pins are not pc interrupt pins * TMC2208/TMC2209 stepper drivers
*
* Software serial communication pins.
* At the moment, F6 rx pins are not pc interrupt pins
*/
#define X_SERIAL_RX_PIN -1 // 71 #define X_SERIAL_RX_PIN -1 // 71
#define X_SERIAL_TX_PIN 72 #define X_SERIAL_TX_PIN 72
#define Y_SERIAL_RX_PIN -1 // 73 #define Y_SERIAL_RX_PIN -1 // 73

@ -1,9 +1,9 @@
/** /**
* Marlin 3D Printer Firmware * Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
* *
* Based on Sprinter and grbl. * Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
* *
* This program is free software: you can redistribute it and/or modify * This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by * it under the terms of the GNU General Public License as published by
@ -99,9 +99,9 @@
#define E4_ENABLE_PIN 47 #define E4_ENABLE_PIN 47
#define E4_CS_PIN E0_CS_PIN #define E4_CS_PIN E0_CS_PIN
#if ENABLED(HAVE_TMC2208) #if HAS_TMC220x
/** /**
* TMC2208 stepper drivers * TMC2208/TMC2209 stepper drivers
* *
* Hardware serial communication ports. * Hardware serial communication ports.
* If undefined software serial is used according to the pins below * If undefined software serial is used according to the pins below

Loading…
Cancel
Save