Update delta configs with latest settings

Marlin/example_configurations/delta/biv2.5/Configuration.h

@@ -355,6 +355,7 @@ Here are some standard links for getting your machine calibrated:
   // #define ENDSTOPPULLUP_XMIN
   // #define ENDSTOPPULLUP_YMIN
   // #define ENDSTOPPULLUP_ZMIN
+  // #define ENDSTOPPULLUP_ZPROBE
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
@@ -368,6 +369,12 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define DISABLE_MAX_ENDSTOPS
 #define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing
 
+// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
+// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
+// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
+// this has no effect.
+//#define DISABLE_Z_PROBE_ENDSTOP
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -430,8 +437,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
                                  // In RAMPS uses servo pin 2. Can be changed in pins file. For other boards pin definition should be made.
                                  // It is assumed that when logic high = filament available
                                  //                    when logic  low = filament ran out
-//const bool FIL_RUNOUT_INVERTING = true;  // Should be uncommented and true or false should assigned
+#ifdef FILAMENT_RUNOUT_SENSOR
-//#define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
+  const bool FIL_RUNOUT_INVERTING = true;  // Should be uncommented and true or false should assigned
+  #define ENDSTOPPULLUP_FIL_RUNOUT // Uncomment to use internal pullup for filament runout pins if the sensor is defined.
+  #define FILAMENT_RUNOUT_SCRIPT "M600"
+#endif
 
 //===========================================================================
 //=========================== Manual Bed Leveling ===========================
@@ -823,6 +833,10 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 
 // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
 //#define LCD_I2C_VIKI
+  
+// SSD1306 OLED generic display support
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define U8GLIB_SSD1306
 
 // Shift register panels
 // ---------------------

Marlin/example_configurations/delta/generic/Configuration.h

@@ -355,6 +355,7 @@ Here are some standard links for getting your machine calibrated:
   // #define ENDSTOPPULLUP_XMIN
   // #define ENDSTOPPULLUP_YMIN
   // #define ENDSTOPPULLUP_ZMIN
+  // #define ENDSTOPPULLUP_ZPROBE
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
@@ -368,6 +369,12 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 //#define DISABLE_MAX_ENDSTOPS
 #define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing
 
+// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
+// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
+// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
+// this has no effect.
+//#define DISABLE_Z_PROBE_ENDSTOP
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -826,6 +833,10 @@ const bool Z_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the logic
 
 // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
 //#define LCD_I2C_VIKI
+  
+// SSD1306 OLED generic display support
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define U8GLIB_SSD1306
 
 // Shift register panels
 // ---------------------

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -355,6 +355,7 @@ Here are some standard links for getting your machine calibrated:
   // #define ENDSTOPPULLUP_XMIN
   // #define ENDSTOPPULLUP_YMIN
   // #define ENDSTOPPULLUP_ZMIN
+  // #define ENDSTOPPULLUP_ZPROBE
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
@@ -368,6 +369,12 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define DISABLE_MAX_ENDSTOPS
 //#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing
 
+// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
+// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
+// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
+// this has no effect.
+//#define DISABLE_Z_PROBE_ENDSTOP
+
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
 #define X_ENABLE_ON 0
@@ -781,6 +788,10 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 
 // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
 //#define LCD_I2C_VIKI
+  
+// SSD1306 OLED generic display support
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
+//#define U8GLIB_SSD1306
 
 // Shift register panels
 // ---------------------

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -307,17 +307,8 @@ Here are some standard links for getting your machine calibrated:
  * the firmware will halt as a safety precaution.
  */
 
-#define THERMAL_RUNAWAY_PROTECTION_HOTENDS // Enable thermal protection for all extruders
+#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
-#define THERMAL_RUNAWAY_PROTECTION_BED     // Enable thermal protection for the heated bed
+#define THERMAL_PROTECTION_BED     // Enable thermal protection for the heated bed
-// Parameters for all extruder heaters
-#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 // in seconds
-#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
-
-// To enable for the bed heater, uncomment the two defines below:
-
-// Parameters for the bed heater
-#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 // in seconds
-#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
 
 //===========================================================================
 //============================= Mechanical Settings =========================
@@ -379,18 +370,10 @@ Here are some standard links for getting your machine calibrated:
   // #define ENDSTOPPULLUP_XMIN
   // #define ENDSTOPPULLUP_YMIN
   // #define ENDSTOPPULLUP_ZMIN
+  // #define ENDSTOPPULLUP_ZPROBE
 #endif
 
-#ifdef ENDSTOPPULLUPS
+// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-  #define ENDSTOPPULLUP_XMAX
-  #define ENDSTOPPULLUP_YMAX
-  #define ENDSTOPPULLUP_ZMAX
-  #define ENDSTOPPULLUP_XMIN
-  #define ENDSTOPPULLUP_YMIN
-  #define ENDSTOPPULLUP_ZMIN
-#endif
-
-// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
 const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
 const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
@@ -401,10 +384,11 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define DISABLE_MAX_ENDSTOPS
 //#define DISABLE_MIN_ENDSTOPS // Deltas only use min endstops for probing
 
-// Disable max endstops for compatibility with endstop checking routine
+// If you want to enable the Z Probe pin, but disable its use, uncomment the line below.
-#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
+// This only affects a Z Probe Endstop if you have separate Z min endstop as well and have
-  #define DISABLE_MAX_ENDSTOPS
+// activated Z_PROBE_ENDSTOP below. If you are using the Z Min endstop on your Z Probe,
-#endif
+// this has no effect.
+//#define DISABLE_Z_PROBE_ENDSTOP
 
 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
 // :{0:'Low',1:'High'}
@@ -477,9 +461,23 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //===========================================================================
 //=========================== Manual Bed Leveling ===========================
 //===========================================================================
-#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
+
-#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
+// #define MANUAL_BED_LEVELING  // Add display menu option for bed leveling
-#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
+// #define MESH_BED_LEVELING    // Enable mesh bed leveling
+
+#ifdef MANUAL_BED_LEVELING
+  #define MBL_Z_STEP 0.025  // Step size while manually probing Z axis
+#endif  // MANUAL_BED_LEVELING
+
+#ifdef MESH_BED_LEVELING
+  #define MESH_MIN_X 10
+  #define MESH_MAX_X (X_MAX_POS - MESH_MIN_X)
+  #define MESH_MIN_Y 10
+  #define MESH_MAX_Y (Y_MAX_POS - MESH_MIN_Y)
+  #define MESH_NUM_X_POINTS 3  // Don't use more than 7 points per axis, implementation limited
+  #define MESH_NUM_Y_POINTS 3
+  #define MESH_HOME_SEARCH_Z 4  // Z after Home, bed somewhere below but above 0.0
+#endif  // MESH_BED_LEVELING
 
 //===========================================================================
 //============================ Bed Auto Leveling ============================
@@ -507,10 +505,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
   // Note: this feature generates 10KB extra code size
   #define AUTO_BED_LEVELING_GRID  // Deltas only support grid mode
 
-  // with AUTO_BED_LEVELING_GRID, the bed is sampled in a
-  // AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
-  // and least squares solution is calculated
-  // Note: this feature occupies 10'206 byte
   #ifdef AUTO_BED_LEVELING_GRID
 
     // set the rectangle in which to probe
@@ -521,16 +515,10 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
     #define BACK_PROBE_BED_POSITION DELTA_PROBABLE_RADIUS
 
     #define MIN_PROBE_EDGE 10 // The probe square sides can be no smaller than this
-    // probe at the points of a lattice grid
-    #define AUTO_BED_LEVELING_GRID_POINTS 7
-    #define AUTO_BED_LEVELING_GRID_X ((RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION) / (AUTO_BED_LEVELING_GRID_POINTS - 1))
-    #define AUTO_BED_LEVELING_GRID_Y ((BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION) / (AUTO_BED_LEVELING_GRID_POINTS - 1))
 
-    // Non-linear bed leveling will be used.
+    // Set the number of grid points per dimension
-    // Compensate by interpolating between the nearest four Z probe values for each point.
+    // You probably don't need more than 3 (squared=9)
-    // Useful for deltas where the print surface may appear like a bowl or dome shape.
+    #define AUTO_BED_LEVELING_GRID_POINTS 7
-    // Works best with ACCURATE_BED_LEVELING_POINTS 5 or higher.
-    #define NONLINEAR_BED_LEVELING
 
   #else  // !AUTO_BED_LEVELING_GRID
 
@@ -710,8 +698,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
  * MOVEMENT SETTINGS
  */
 
-  ////// #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
-// set the homing speeds (mm/min)
 /// delta homing speeds must be the same on xyz
 #define HOMING_FEEDRATE_X (200*60)
 #define HOMING_FEEDRATE_Y (200*60)
@@ -735,12 +721,6 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 #define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration in mm/s^2 for retracts
 #define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration in mm/s^2 for travel (non printing) moves
 
-// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
-// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
-// For the other hotends it is their distance from the extruder 0 hotend.
-// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
-// #define EXTRUDER_OFFSET_Y {0.0, 5.00}  // (in mm) for each extruder, offset of the hotend on the Y axis
-
 // The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
 #define DEFAULT_XYJERK                20.0    // (mm/sec)
 #define DEFAULT_ZJERK                 20.0    // (mm/sec) Must be same as XY for delta
@@ -771,6 +751,8 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 // M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
 // M502 - reverts to the default "factory settings".  You still need to store them in EEPROM afterwards if you want to.
 //define this to enable EEPROM support
+//#define EEPROM_SETTINGS
+
 #ifdef EEPROM_SETTINGS
   // To disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
   #define EEPROM_CHITCHAT // Please keep turned on if you can.
@@ -814,6 +796,9 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 // the duration the buzzer plays the UI feedback sound. ie Screen Click
 //#define LCD_FEEDBACK_FREQUENCY_HZ 1000         // this is the tone frequency the buzzer plays when on UI feedback. ie Screen Click
                                                  // 0 to disable buzzer feedback. Test with M300 S<frequency Hz> P<duration ms>
+// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3)
+// http://reprap.org/wiki/PanelOne
+//#define PANEL_ONE
 
 // The MaKr3d Makr-Panel with graphic controller and SD support
 // http://reprap.org/wiki/MaKr3d_MaKrPanel
@@ -829,6 +814,7 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 //
 // ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
 //#define ELB_FULL_GRAPHIC_CONTROLLER
+//#define SDCARDDETECTINVERTED
 
 // The RepRapDiscount Smart Controller (white PCB)
 // http://reprap.org/wiki/RepRapDiscount_Smart_Controller
@@ -854,136 +840,37 @@ const bool Z_PROBE_ENDSTOP_INVERTING = false; // set to true to invert the logic
 // REMEMBER TO INSTALL LiquidCrystal_I2C.h in your ARDUINO library folder: https://github.com/kiyoshigawa/LiquidCrystal_I2C
 //#define RA_CONTROL_PANEL
 
-//automatic expansion
+// Delta calibration menu
-#if defined (MAKRPANEL)
+// uncomment to add three points calibration menu option.
- #define DOGLCD
+// See http://minow.blogspot.com/index.html#4918805519571907051
- #define SDSUPPORT
+// If needed, adjust the X, Y, Z calibration coordinates
- #define ULTIPANEL
+// in ultralcd.cpp@lcd_delta_calibrate_menu()
- #define NEWPANEL
+// #define DELTA_CALIBRATION_MENU
- #define DEFAULT_LCD_CONTRAST 17
-#endif
-
-#if defined (REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER)
- #define DOGLCD
- #define U8GLIB_ST7920
- #define REPRAP_DISCOUNT_SMART_CONTROLLER
-#endif
-
-#if defined(ULTIMAKERCONTROLLER) || defined(REPRAP_DISCOUNT_SMART_CONTROLLER) || defined(G3D_PANEL)
- #define ULTIPANEL
- #define NEWPANEL
-#endif
-
-#if defined(REPRAPWORLD_KEYPAD)
-  #define NEWPANEL
-  #define ULTIPANEL
-#endif
-#if defined(RA_CONTROL_PANEL)
- #define ULTIPANEL
- #define NEWPANEL
- #define LCD_I2C_TYPE_PCA8574
- #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander
-#endif
 
 /**
  * I2C Panels
  */
 
 //#define LCD_I2C_SAINSMART_YWROBOT
-#ifdef LCD_I2C_SAINSMART_YWROBOT
-  // This uses the LiquidCrystal_I2C library ( https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home )
-  // Make sure it is placed in the Arduino libraries directory.
-  #define LCD_I2C_TYPE_PCF8575
-  #define LCD_I2C_ADDRESS 0x27   // I2C Address of the port expander
-  #define NEWPANEL
-  #define ULTIPANEL
-#endif
 
 // PANELOLU2 LCD with status LEDs, separate encoder and click inputs
 //#define LCD_I2C_PANELOLU2
-#ifdef LCD_I2C_PANELOLU2
-  // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
-  // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
-  // (v1.2.3 no longer requires you to define PANELOLU in the LiquidTWI2.h library header file)
-  // Note: The PANELOLU2 encoder click input can either be directly connected to a pin
-  //       (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1).
-  #define LCD_I2C_TYPE_MCP23017
-  #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
-  #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD
-  #define NEWPANEL
-  #define ULTIPANEL
-
-  #ifndef ENCODER_PULSES_PER_STEP
-	#define ENCODER_PULSES_PER_STEP 4
-  #endif
-
-  #ifndef ENCODER_STEPS_PER_MENU_ITEM
-	#define ENCODER_STEPS_PER_MENU_ITEM 1
-  #endif
-
-
-  #ifdef LCD_USE_I2C_BUZZER
-	#define LCD_FEEDBACK_FREQUENCY_HZ 1000
-	#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100
-  #endif
-
-#endif
 
 // Panucatt VIKI LCD with status LEDs, integrated click & L/R/U/P buttons, separate encoder inputs
 //#define LCD_I2C_VIKI
-#ifdef LCD_I2C_VIKI
+  
-  // This uses the LiquidTWI2 library v1.2.3 or later ( https://github.com/lincomatic/LiquidTWI2 )
+// SSD1306 OLED generic display support
-  // Make sure the LiquidTWI2 directory is placed in the Arduino or Sketchbook libraries subdirectory.
+// ==> REMEMBER TO INSTALL U8glib to your ARDUINO library folder: http://code.google.com/p/u8glib/wiki/u8glib
-  // Note: The pause/stop/resume LCD button pin should be connected to the Arduino
+//#define U8GLIB_SSD1306
-  //       BTN_ENC pin (or set BTN_ENC to -1 if not used)
-  #define LCD_I2C_TYPE_MCP23017
-  #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
-  #define LCD_USE_I2C_BUZZER //comment out to disable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later)
-  #define NEWPANEL
-  #define ULTIPANEL
-#endif
 
 // Shift register panels
 // ---------------------
 // 2 wire Non-latching LCD SR from:
 // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection
-//#define SR_LCD
+// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD
-#ifdef SR_LCD
+//#define SAV_3DLCD
-   #define SR_LCD_2W_NL    // Non latching 2 wire shift register
-   //#define NEWPANEL
-#endif
-
 
 // @section extras
-#ifdef ULTIPANEL
-//  #define NEWPANEL  //enable this if you have a click-encoder panel
-  #define SDSUPPORT
-  #define ULTRA_LCD
-  #ifdef DOGLCD // Change number of lines to match the DOG graphic display
-    #define LCD_WIDTH 20
-    #define LCD_HEIGHT 5
-  #else
-    #define LCD_WIDTH 20
-    #define LCD_HEIGHT 4
-  #endif
-#else //no panel but just LCD
-  #ifdef ULTRA_LCD
-  #ifdef DOGLCD // Change number of lines to match the 128x64 graphics display
-    #define LCD_WIDTH 20
-    #define LCD_HEIGHT 5
-  #else
-    #define LCD_WIDTH 16
-    #define LCD_HEIGHT 2
-  #endif
-  #endif
-#endif
-
-// default LCD contrast for dogm-like LCD displays
-#ifdef DOGLCD
-# ifndef DEFAULT_LCD_CONTRAST
-#  define DEFAULT_LCD_CONTRAST 32
-# endif
-#endif
 
 // Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
 //#define FAST_PWM_FAN