SD_DETECT_INVERTED => SD_DETECT_STATE (#17112)

Marlin/Configuration_adv.h

@@ -1018,12 +1018,9 @@
 
 #if ENABLED(SDSUPPORT)
 
-  // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
+  // The standard SD detect circuit reads LOW when media is inserted and HIGH when empty.
-  // around this by connecting a push button or single throw switch to the pin defined
+  // Enable this option and set to HIGH if your SD cards are incorrectly detected.
-  // as SD_DETECT_PIN in your board's pins definitions.
+  //#define SD_DETECT_STATE HIGH
-  // This setting should be disabled unless you are using a push button, pulling the pin to ground.
-  // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
-  #define SD_DETECT_INVERTED
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.

Marlin/src/inc/Conditionals_LCD.h

@@ -74,7 +74,6 @@
     #define U8GLIB_ST7565_64128N
   #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
     #define U8GLIB_LM6059_AF
-    #define SD_DETECT_INVERTED
   #elif ENABLED(AZSMZ_12864)
     #define U8GLIB_ST7565_64128N
   #endif

Marlin/src/inc/Conditionals_post.h

@@ -292,10 +292,18 @@
 #endif
 
 /**
- * Override here because this is set in Configuration_adv.h
+ * Override the SD_DETECT_STATE set in Configuration_adv.h
  */
-#if HAS_LCD_MENU && DISABLED(ELB_FULL_GRAPHIC_CONTROLLER) && (SD_CONNECTION_IS(LCD) || !defined(SDCARD_CONNECTION))
+#if ENABLED(SDSUPPORT)
-  #undef SD_DETECT_INVERTED
+  #if HAS_LCD_MENU && (SD_CONNECTION_IS(LCD) || !defined(SDCARD_CONNECTION))
+    #undef SD_DETECT_STATE
+    #if ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
+      #define SD_DETECT_STATE HIGH
+    #endif
+  #endif
+  #ifndef SD_DETECT_STATE
+    #define SD_DETECT_STATE LOW
+  #endif
 #endif
 
 /**

Marlin/src/inc/SanityCheck.h

@@ -99,7 +99,9 @@
 #elif defined(X_HOME_RETRACT_MM)
   #error "[XYZ]_HOME_RETRACT_MM settings have been renamed [XYZ]_HOME_BUMP_MM."
 #elif defined(SDCARDDETECTINVERTED)
-  #error "SDCARDDETECTINVERTED is now SD_DETECT_INVERTED. Please update your configuration."
+  #error "SDCARDDETECTINVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration."
+#elif defined(SD_DETECT_INVERTED)
+  #error "SD_DETECT_INVERTED is now SD_DETECT_STATE (HIGH). Please update your configuration."
 #elif defined(BTENABLED)
   #error "BTENABLED is now BLUETOOTH. Please update your configuration."
 #elif defined(CUSTOM_MENDEL_NAME)

Marlin/src/pins/ramps/pins_FYSETC_F6_13.h

@@ -29,10 +29,6 @@
   #error "Oops! Select 'FYSETC F6' in 'Tools > Board.'"
 #endif
 
-#if ENABLED(SD_DETECT_INVERTED)
-  //#error "SD_DETECT_INVERTED must be disabled for the FYSETC_F6_13 board."
-#endif
-
 #ifndef BOARD_INFO_NAME
   #define BOARD_INFO_NAME "FYSETC F6 1.3"
 #endif

Marlin/src/sd/cardreader.h

@@ -276,7 +276,7 @@ private:
 #if ENABLED(USB_FLASH_DRIVE_SUPPORT)
   #define IS_SD_INSERTED() Sd2Card::isInserted()
 #elif PIN_EXISTS(SD_DETECT)
-  #define IS_SD_INSERTED() (READ(SD_DETECT_PIN) != ENABLED(SD_DETECT_INVERTED))
+  #define IS_SD_INSERTED() (READ(SD_DETECT_PIN) == SD_DETECT_STATE)
 #else
   // No card detect line? Assume the card is inserted.
   #define IS_SD_INSERTED() true