Spacing adjustments in some pins files

Marlin/pins_AZTEEG_X3.h

@@ -24,8 +24,8 @@
  #define SDCARDDETECT -1 // Pin 49 if using display sd interface   
  
   #if ENABLED(TEMP_STAT_LEDS)
-   #define STAT_LED_RED 64
-   #define STAT_LED_BLUE 63
+    #define STAT_LED_RED 64
+    #define STAT_LED_BLUE 63
   #endif
 
 #elif ENABLED(TEMP_STAT_LEDS)

Marlin/pins_ELEFU_3.h

@@ -13,14 +13,14 @@
 #define X_MAX_PIN          34
 
 #define Y_STEP_PIN         11
-#define Y_DIR_PIN          9
+#define Y_DIR_PIN           9
 #define Y_ENABLE_PIN       12
 #define Y_MIN_PIN          33
 #define Y_MAX_PIN          32
 
-#define Z_STEP_PIN         7
-#define Z_DIR_PIN          6
-#define Z_ENABLE_PIN       8
+#define Z_STEP_PIN          7
+#define Z_DIR_PIN           6
+#define Z_ENABLE_PIN        8
 #define Z_MIN_PIN          31
 #define Z_MAX_PIN          30
 
@@ -48,10 +48,10 @@
 #define HEATER_1_PIN       46 //12V PWM2
 #define HEATER_2_PIN       17 //12V PWM3
 #define HEATER_BED_PIN     44 //DOUBLE 12V PWM
-#define TEMP_0_PIN         3  //ANALOG NUMBERING
-#define TEMP_1_PIN         2  //ANALOG NUMBERING
-#define TEMP_2_PIN         1  //ANALOG NUMBERING
-#define TEMP_BED_PIN       0  //ANALOG NUMBERING
+#define TEMP_0_PIN          3 //ANALOG NUMBERING
+#define TEMP_1_PIN          2 //ANALOG NUMBERING
+#define TEMP_2_PIN          1 //ANALOG NUMBERING
+#define TEMP_BED_PIN        0 //ANALOG NUMBERING
 
 #define BEEPER_PIN         36
 
@@ -70,9 +70,9 @@
   #define BTN_EN2          39
   #define BTN_ENC          15  //the click
 
-  #define BLEN_C           2
-  #define BLEN_B           1
-  #define BLEN_A           0
+  #define BLEN_C            2
+  #define BLEN_B            1
+  #define BLEN_A            0
 
 #endif // RA_CONTROL_PANEL
 

Marlin/pins_MINIRAMBO.h

@@ -89,7 +89,9 @@
 #define SUICIDE_PIN        -1  //PIN that has to be turned on right after start, to keep power flowing.
 
 #if ENABLED(ULTRA_LCD)
+
   #define KILL_PIN 32
+
   #if ENABLED(NEWPANEL)
 
     #define BEEPER_PIN 84      // Beeper on AUX-4
@@ -107,5 +109,5 @@
 
     #define SDCARDDETECT 15
 
-  #endif
+  #endif //NEWPANEL
 #endif //ULTRA_LCD

Marlin/pins_RAMBO.h

@@ -110,7 +110,9 @@
 #define SUICIDE_PIN        -1  //PIN that has to be turned on right after start, to keep power flowing.
 
 #if ENABLED(ULTRA_LCD)
+
   #define KILL_PIN 80
+
   #if ENABLED(NEWPANEL)
 
     #define BEEPER_PIN 79      // Beeper on AUX-4
@@ -138,7 +140,7 @@
     #define BEEPER_PIN 33    // No Beeper added
 
     //buttons are attached to a shift register
-    // Not wired this yet
+    // Not wired yet
     // #define SHIFT_CLK 38
     // #define SHIFT_LD 42
     // #define SHIFT_OUT 40

Marlin/pins_TEENSYLU.h

@@ -68,7 +68,6 @@
 #endif
 
 #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
-  //LCD Pins
 
   #define BEEPER_PIN -1
 
@@ -78,7 +77,8 @@
     #define BTN_ENC 43 //A3 - fastio.h pin mapping 43
     #define SDSS   40 //use SD card on Panelolu2 (Teensyduino pin mapping)
   #endif // LCD_I2C_PANELOLU2
-  //not connected to a pin
+
   #define SDCARDDETECT -1    
+
 #endif // ULTRA_LCD && NEWPANEL