microlab
/
scube
1
1
Fork 0
Code Issues Pull Requests Releases Activity

Set more regular setup in configuration.h

Browse Source
2.0.x
alexborro 10 years ago
parent 60ceca1bc1
commit 8a4b62d081
1 changed files with 35 additions and 48 deletions
Show Stats Download Patch File Download Diff File

69
Marlin/Configuration.h
Unescape Escape View File

@ -59,7 +59,7 @@ Here are some standard links for getting your machine calibrated:
// The following define selects which electronics board you have. // The following define selects which electronics board you have.
// Please choose the name from boards.h that matches your setup // Please choose the name from boards.h that matches your setup
#ifndef MOTHERBOARD #ifndef MOTHERBOARD
#define MOTHERBOARD BOARD_ULTIMAKER #define MOTHERBOARD BOARD_RAMPS_13
#endif #endif
// Define this to set a custom name for your generic Mendel, // Define this to set a custom name for your generic Mendel,
@ -123,8 +123,8 @@ Here are some standard links for getting your machine calibrated:
// #define DUMMY_THERMISTOR_998_VALUE 25 // #define DUMMY_THERMISTOR_998_VALUE 25
// #define DUMMY_THERMISTOR_999_VALUE 100 // #define DUMMY_THERMISTOR_999_VALUE 100
#define TEMP_SENSOR_0 -1 #define TEMP_SENSOR_0 1
#define TEMP_SENSOR_1 -1 #define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0 #define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0 #define TEMP_SENSOR_3 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
@ -301,35 +301,21 @@ your extruder heater takes 2 minutes to hit the target on heating.
// Enable this option for Toshiba steppers // Enable this option for Toshiba steppers
// #define CONFIG_STEPPERS_TOSHIBA // #define CONFIG_STEPPERS_TOSHIBA
// coarse Endstop Settings // The pullups are needed if you directly connect a mechanical endstop between the signal and ground pins.
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
#ifndef ENDSTOPPULLUPS
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
// #define ENDSTOPPULLUP_XMAX
// #define ENDSTOPPULLUP_YMAX
// #define ENDSTOPPULLUP_ZMAX
// #define ENDSTOPPULLUP_XMIN
// #define ENDSTOPPULLUP_YMIN
// #define ENDSTOPPULLUP_ZMIN
#endif
#ifdef ENDSTOPPULLUPS
#define ENDSTOPPULLUP_XMAX #define ENDSTOPPULLUP_XMAX
#define ENDSTOPPULLUP_YMAX #define ENDSTOPPULLUP_YMAX
#define ENDSTOPPULLUP_ZMAX #define ENDSTOPPULLUP_ZMAX
#define ENDSTOPPULLUP_XMIN #define ENDSTOPPULLUP_XMIN
#define ENDSTOPPULLUP_YMIN #define ENDSTOPPULLUP_YMIN
#define ENDSTOPPULLUP_ZMIN #define ENDSTOPPULLUP_ZMIN
#endif
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins. // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
const bool X_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. const bool X_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Y_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. const bool Y_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Z_MIN_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. const bool Z_MIN_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool X_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. const bool X_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Y_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. const bool Y_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of the endstop. const bool Z_MAX_ENDSTOP_INVERTING = false; // set to true to invert the logic of the endstop.
//#define DISABLE_MAX_ENDSTOPS //#define DISABLE_MAX_ENDSTOPS
//#define DISABLE_MIN_ENDSTOPS //#define DISABLE_MIN_ENDSTOPS
@ -346,13 +332,14 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define DISABLE_E false // For all extruders #define DISABLE_E false // For all extruders
#define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled #define DISABLE_INACTIVE_EXTRUDER true //disable only inactive extruders and keep active extruder enabled
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true // If you motor turns to wrong direction, you can invert it here:
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false #define INVERT_X_DIR false
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true #define INVERT_Y_DIR false
#define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_Z_DIR false
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E0_DIR false
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E1_DIR false
#define INVERT_E3_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E2_DIR false
#define INVERT_E3_DIR false
// ENDSTOP SETTINGS: // ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN // Sets direction of endstops when homing; 1=MAX, -1=MIN
@ -364,9 +351,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below. #define max_software_endstops true // If true, axis won't move to coordinates greater than the defined lengths below.
// Travel limits after homing (units are in mm) // Travel limits after homing (units are in mm)
#define X_MAX_POS 205 #define X_MAX_POS 200
#define X_MIN_POS 0 #define X_MIN_POS 0
#define Y_MAX_POS 205 #define Y_MAX_POS 200
#define Y_MIN_POS 0 #define Y_MIN_POS 0
#define Z_MAX_POS 200 #define Z_MAX_POS 200
#define Z_MIN_POS 0 #define Z_MIN_POS 0
@ -443,7 +430,7 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
#define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point. #define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
#define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points #define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine. // #define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" //These commands will be executed in the end of G29 routine.
//Useful to retract a deployable probe. //Useful to retract a deployable probe.
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell //#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
@ -493,9 +480,9 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
// default settings // default settings
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200.0*8/3,760*1.1} // default steps per unit for Ultimaker #define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,500} // default steps per unit for Ultimaker
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 25} // (mm/sec) #define DEFAULT_MAX_FEEDRATE {300, 300, 5, 25} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot. #define DEFAULT_MAX_ACCELERATION {3000,3000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts #define DEFAULT_RETRACT_ACCELERATION 3000 // X, Y, Z and E max acceleration in mm/s^2 for retracts
@ -539,11 +526,11 @@ const bool Z_MAX_ENDSTOP_INVERTING = true; // set to true to invert the logic of
// Preheat Constants // Preheat Constants
#define PLA_PREHEAT_HOTEND_TEMP 180 #define PLA_PREHEAT_HOTEND_TEMP 180
#define PLA_PREHEAT_HPB_TEMP 70 #define PLA_PREHEAT_HPB_TEMP 70
#define PLA_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 #define PLA_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
#define ABS_PREHEAT_HOTEND_TEMP 240 #define ABS_PREHEAT_HOTEND_TEMP 240
#define ABS_PREHEAT_HPB_TEMP 100 #define ABS_PREHEAT_HPB_TEMP 110
#define ABS_PREHEAT_FAN_SPEED 255 // Insert Value between 0 and 255 #define ABS_PREHEAT_FAN_SPEED 0 // Insert Value between 0 and 255
//==============================LCD and SD support============================= //==============================LCD and SD support=============================

Write Preview
Loading…
Cancel
Save