microlab
/
scube
1
1
Fork 0
Code Issues Pull Requests Releases Activity

M141 Heated Chamber, Temperature rework (#12201)

Browse Source
2.0.x
3dlabsio 6 years ago committed by Scott Lahteine
parent 44571775bd
commit 645ca7af7a
196 changed files with 2184 additions and 677 deletions
Show Stats Download Patch File Download Diff File

2
Marlin/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
Marlin/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
Marlin/src/core/language.h
Unescape Escape View File

@ -285,6 +285,8 @@
#define MSG_INVALID_EXTRUDER_NUM " - Invalid extruder number !" #define MSG_INVALID_EXTRUDER_NUM " - Invalid extruder number !"
#define MSG_HEATER_BED "bed" #define MSG_HEATER_BED "bed"
#define MSG_HEATER_CHAMBER "chamber"
#define MSG_STOPPED_HEATER ", system stopped! Heater_ID: " #define MSG_STOPPED_HEATER ", system stopped! Heater_ID: "
#define MSG_REDUNDANCY "Heater switched off. Temperature difference between temp sensors is too high !" #define MSG_REDUNDANCY "Heater switched off. Temperature difference between temp sensors is too high !"
#define MSG_T_HEATING_FAILED "Heating failed" #define MSG_T_HEATING_FAILED "Heating failed"

2
Marlin/src/feature/controllerfan.cpp
Unescape Escape View File

@ -39,7 +39,7 @@ void controllerfan_update() {
// If any of the drivers or the bed are enabled... // If any of the drivers or the bed are enabled...
if (X_ENABLE_READ == X_ENABLE_ON || Y_ENABLE_READ == Y_ENABLE_ON || Z_ENABLE_READ == Z_ENABLE_ON if (X_ENABLE_READ == X_ENABLE_ON || Y_ENABLE_READ == Y_ENABLE_ON || Z_ENABLE_READ == Z_ENABLE_ON
#if HAS_HEATED_BED #if HAS_HEATED_BED
|| thermalManager.soft_pwm_amount_bed > 0 || thermalManager.temp_bed.soft_pwm_amount > 0
#endif #endif
#if HAS_X2_ENABLE #if HAS_X2_ENABLE
|| X2_ENABLE_READ == X_ENABLE_ON || X2_ENABLE_READ == X_ENABLE_ON

10
Marlin/src/feature/pause.cpp
Unescape Escape View File

@ -482,8 +482,7 @@ void wait_for_confirmation(const bool is_reload/*=false*/, const int8_t max_beep
// Start the heater idle timers // Start the heater idle timers
const millis_t nozzle_timeout = (millis_t)(PAUSE_PARK_NOZZLE_TIMEOUT) * 1000UL; const millis_t nozzle_timeout = (millis_t)(PAUSE_PARK_NOZZLE_TIMEOUT) * 1000UL;
HOTEND_LOOP() HOTEND_LOOP() thermalManager.hotend_idle[e].start(nozzle_timeout);
thermalManager.start_heater_idle_timer(e, nozzle_timeout);
#if ENABLED(DUAL_X_CARRIAGE) #if ENABLED(DUAL_X_CARRIAGE)
const int8_t saved_ext = active_extruder; const int8_t saved_ext = active_extruder;
@ -505,7 +504,7 @@ void wait_for_confirmation(const bool is_reload/*=false*/, const int8_t max_beep
// If the nozzle has timed out... // If the nozzle has timed out...
if (!nozzle_timed_out) if (!nozzle_timed_out)
HOTEND_LOOP() nozzle_timed_out |= thermalManager.is_heater_idle(e); HOTEND_LOOP() nozzle_timed_out |= thermalManager.hotend_idle[e].timed_out;
// Wait for the user to press the button to re-heat the nozzle, then // Wait for the user to press the button to re-heat the nozzle, then
// re-heat the nozzle, re-show the continue prompt, restart idle timers, start over // re-heat the nozzle, re-show the continue prompt, restart idle timers, start over
@ -538,8 +537,7 @@ void wait_for_confirmation(const bool is_reload/*=false*/, const int8_t max_beep
// Start the heater idle timers // Start the heater idle timers
const millis_t nozzle_timeout = (millis_t)(PAUSE_PARK_NOZZLE_TIMEOUT) * 1000UL; const millis_t nozzle_timeout = (millis_t)(PAUSE_PARK_NOZZLE_TIMEOUT) * 1000UL;
HOTEND_LOOP() HOTEND_LOOP() thermalManager.hotend_idle[e].start(nozzle_timeout);
thermalManager.start_heater_idle_timer(e, nozzle_timeout);
#if ENABLED(HOST_PROMPT_SUPPORT) #if ENABLED(HOST_PROMPT_SUPPORT)
host_prompt_do(PROMPT_USER_CONTINUE, PSTR("Reheat Done"), PSTR("Continue")); host_prompt_do(PROMPT_USER_CONTINUE, PSTR("Reheat Done"), PSTR("Continue"));
#endif #endif
@ -594,7 +592,7 @@ void resume_print(const float &slow_load_length/*=0*/, const float &fast_load_le
// Re-enable the heaters if they timed out // Re-enable the heaters if they timed out
bool nozzle_timed_out = false; bool nozzle_timed_out = false;
HOTEND_LOOP() { HOTEND_LOOP() {
nozzle_timed_out |= thermalManager.is_heater_idle(e); nozzle_timed_out |= thermalManager.hotend_idle[e].timed_out;
thermalManager.reset_heater_idle_timer(e); thermalManager.reset_heater_idle_timer(e);
} }

2
Marlin/src/feature/power.cpp
Unescape Escape View File

@ -53,7 +53,7 @@ bool Power::is_power_needed() {
// If any of the drivers or the bed are enabled... // If any of the drivers or the bed are enabled...
if (X_ENABLE_READ == X_ENABLE_ON || Y_ENABLE_READ == Y_ENABLE_ON || Z_ENABLE_READ == Z_ENABLE_ON if (X_ENABLE_READ == X_ENABLE_ON || Y_ENABLE_READ == Y_ENABLE_ON || Z_ENABLE_READ == Z_ENABLE_ON
#if HAS_HEATED_BED #if HAS_HEATED_BED
|| thermalManager.soft_pwm_amount_bed > 0 || thermalManager.temp_bed.soft_pwm_amount > 0
#endif #endif
#if HAS_X2_ENABLE #if HAS_X2_ENABLE
|| X2_ENABLE_READ == X_ENABLE_ON || X2_ENABLE_READ == X_ENABLE_ON

6
Marlin/src/feature/power_loss_recovery.cpp
Unescape Escape View File

@ -155,10 +155,10 @@ void PrintJobRecovery::save(const bool force/*=false*/, const bool save_queue/*=
info.active_hotend = active_extruder; info.active_hotend = active_extruder;
#endif #endif
COPY(info.target_temperature, thermalManager.target_temperature); HOTEND_LOOP() info.target_temperature[e] = thermalManager.temp_hotend[e].target;
#if HAS_HEATED_BED #if HAS_HEATED_BED
info.target_temperature_bed = thermalManager.target_temperature_bed; info.target_temperature_bed = thermalManager.temp_bed.target;
#endif #endif
#if FAN_COUNT #if FAN_COUNT
@ -385,7 +385,7 @@ void PrintJobRecovery::resume() {
#if FAN_COUNT #if FAN_COUNT
SERIAL_ECHOPGM("fan_speed: "); SERIAL_ECHOPGM("fan_speed: ");
for (int8_t i = 0; i < FAN_COUNT; i++) { FANS_LOOP(i) {
SERIAL_ECHO(int(info.fan_speed[i])); SERIAL_ECHO(int(info.fan_speed[i]));
if (i < FAN_COUNT - 1) SERIAL_CHAR(','); if (i < FAN_COUNT - 1) SERIAL_CHAR(',');
} }

12
Marlin/src/gcode/config/M304.cpp
Unescape Escape View File

@ -28,14 +28,14 @@
#include "../../module/temperature.h" #include "../../module/temperature.h"
void GcodeSuite::M304() { void GcodeSuite::M304() {
if (parser.seen('P')) thermalManager.bed_pid.Kp = parser.value_float(); if (parser.seen('P')) thermalManager.temp_bed.pid.Kp = parser.value_float();
if (parser.seen('I')) thermalManager.bed_pid.Ki = scalePID_i(parser.value_float()); if (parser.seen('I')) thermalManager.temp_bed.pid.Ki = scalePID_i(parser.value_float());
if (parser.seen('D')) thermalManager.bed_pid.Kd = scalePID_d(parser.value_float()); if (parser.seen('D')) thermalManager.temp_bed.pid.Kd = scalePID_d(parser.value_float());
SERIAL_ECHO_START(); SERIAL_ECHO_START();
SERIAL_ECHOPAIR(" p:", thermalManager.bed_pid.Kp); SERIAL_ECHOPAIR(" p:", thermalManager.temp_bed.pid.Kp);
SERIAL_ECHOPAIR(" i:", unscalePID_i(thermalManager.bed_pid.Ki)); SERIAL_ECHOPAIR(" i:", unscalePID_i(thermalManager.temp_bed.pid.Ki));
SERIAL_ECHOLNPAIR(" d:", unscalePID_d(thermalManager.bed_pid.Kd)); SERIAL_ECHOLNPAIR(" d:", unscalePID_d(thermalManager.temp_bed.pid.Kd));
} }
#endif // PIDTEMPBED #endif // PIDTEMPBED

5
Marlin/src/gcode/gcode.cpp
Unescape Escape View File

@ -392,6 +392,11 @@ void GcodeSuite::process_parsed_command(
case 190: M190(); break; // M190: Wait for bed temperature to reach target case 190: M190(); break; // M190: Wait for bed temperature to reach target
#endif #endif
#if HAS_HEATED_CHAMBER
case 141: M141(); break; // M141: Set chamber temperature
//case 191: M191(); break; // M191: Wait for chamber temperature to reach target
#endif
case 105: M105(); KEEPALIVE_STATE(NOT_BUSY); return; // M105: Report Temperatures (and say "ok") case 105: M105(); KEEPALIVE_STATE(NOT_BUSY); return; // M105: Report Temperatures (and say "ok")
#if ENABLED(AUTO_REPORT_TEMPERATURES) && HAS_TEMP_SENSOR #if ENABLED(AUTO_REPORT_TEMPERATURES) && HAS_TEMP_SENSOR

5
Marlin/src/gcode/gcode.h
Unescape Escape View File

@ -576,6 +576,11 @@ private:
static void M190(); static void M190();
#endif #endif
#if HAS_HEATED_CHAMBER
static void M141();
//static void M191();
#endif
#if HAS_LCD_MENU #if HAS_LCD_MENU
static void M145(); static void M145();
#endif #endif

77
Marlin/src/gcode/temperature/M141_M191.cpp
Unescape Escape View File

@ -0,0 +1,77 @@
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
#include "../../inc/MarlinConfig.h"
#if HAS_HEATED_CHAMBER
#include "../gcode.h"
#include "../../module/temperature.h"
/*
#include "../../module/motion.h"
#include "../../lcd/ultralcd.h"
#if ENABLED(PRINTJOB_TIMER_AUTOSTART)
#include "../../module/printcounter.h"
#endif
#if ENABLED(PRINTER_EVENT_LEDS)
#include "../../feature/leds/leds.h"
#endif
#include "../../Marlin.h" // for wait_for_heatup and idle()
*/
/**
* M141: Set chamber temperature
*/
void GcodeSuite::M141() {
if (DEBUGGING(DRYRUN)) return;
if (parser.seenval('S')) thermalManager.setTargetChamber(parser.value_celsius());
}
/**
* M191: Sxxx Wait for chamber current temp to reach target temp. Waits only when heating
* Rxxx Wait for chamber current temp to reach target temp. Waits when heating and cooling
*/
/*
void GcodeSuite::M191() {
if (DEBUGGING(DRYRUN)) return;
const bool no_wait_for_cooling = parser.seenval('S');
if (no_wait_for_cooling || parser.seenval('R')) {
thermalManager.setTargetBed(parser.value_celsius());
#if ENABLED(PRINTJOB_TIMER_AUTOSTART)
if (parser.value_celsius() > BED_MINTEMP)
print_job_timer.start();
#endif
}
else return;
lcd_setstatusPGM(thermalManager.isHeatingBed() ? PSTR(MSG_BED_HEATING) : PSTR(MSG_BED_COOLING));
thermalManager.wait_for_bed(no_wait_for_cooling);
}
*/
#endif // HAS_HEATED_CHAMBER

17
Marlin/src/inc/Conditionals_post.h
Unescape Escape View File

@ -921,6 +921,7 @@
#define HAS_TEMP_HOTEND (HAS_TEMP_ADC_0 || ENABLED(HEATER_0_USES_MAX6675)) #define HAS_TEMP_HOTEND (HAS_TEMP_ADC_0 || ENABLED(HEATER_0_USES_MAX6675))
#define HAS_TEMP_BED HAS_TEMP_ADC_BED #define HAS_TEMP_BED HAS_TEMP_ADC_BED
#define HAS_TEMP_CHAMBER HAS_TEMP_ADC_CHAMBER #define HAS_TEMP_CHAMBER HAS_TEMP_ADC_CHAMBER
#define HAS_HEATED_CHAMBER (HAS_TEMP_CHAMBER && PIN_EXISTS(CHAMBER_HEATER))
// Heaters // Heaters
#define HAS_HEATER_0 (PIN_EXISTS(HEATER_0)) #define HAS_HEATER_0 (PIN_EXISTS(HEATER_0))
@ -945,7 +946,8 @@
// Thermal protection // Thermal protection
#define HAS_THERMALLY_PROTECTED_BED (HAS_HEATED_BED && ENABLED(THERMAL_PROTECTION_BED)) #define HAS_THERMALLY_PROTECTED_BED (HAS_HEATED_BED && ENABLED(THERMAL_PROTECTION_BED))
#define WATCH_HOTENDS (ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0) #define WATCH_HOTENDS (ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0)
#define WATCH_THE_BED (HAS_THERMALLY_PROTECTED_BED && WATCH_BED_TEMP_PERIOD > 0) #define WATCH_BED (HAS_THERMALLY_PROTECTED_BED && WATCH_BED_TEMP_PERIOD > 0)
#define WATCH_CHAMBER (HAS_HEATED_CHAMBER && ENABLED(THERMAL_PROTECTION_CHAMBER) && WATCH_CHAMBER_TEMP_PERIOD > 0)
// Auto fans // Auto fans
#define HAS_AUTO_FAN_0 (PIN_EXISTS(E0_AUTO_FAN)) #define HAS_AUTO_FAN_0 (PIN_EXISTS(E0_AUTO_FAN))
@ -1151,6 +1153,19 @@
#define WRITE_HEATER_BED(v) WRITE(HEATER_BED_PIN, (v) ^ HEATER_BED_INVERTING) #define WRITE_HEATER_BED(v) WRITE(HEATER_BED_PIN, (v) ^ HEATER_BED_INVERTING)
#endif #endif
/**
* Heated chamber requires settings
*/
#if HAS_HEATED_CHAMBER
#ifndef MAX_CHAMBER_POWER
#define MAX_CHAMBER_POWER 255
#endif
#ifndef HEATER_CHAMBER_INVERTING
#define HEATER_CHAMBER_INVERTING false
#endif
#define WRITE_HEATER_CHAMBER(v) WRITE(HEATER_CHAMBER_PIN, (v) ^ HEATER_CHAMBER_INVERTING)
#endif
/** /**
* Up to 3 PWM fans * Up to 3 PWM fans
*/ */

4
Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp
Unescape Escape View File

@ -544,9 +544,9 @@ FORCE_INLINE void _draw_heater_status(const int8_t heater, const char prefix, co
#else #else
const bool is_idle = ( const bool is_idle = (
#if HAS_HEATED_BED #if HAS_HEATED_BED
isBed ? thermalManager.is_bed_idle() : isBed ? thermalManager.bed_idle.timed_out :
#endif #endif
thermalManager.is_heater_idle(heater) thermalManager.hotend_idle[heater].timed_out
); );
if (!blink && is_idle) { if (!blink && is_idle) {

2
Marlin/src/lcd/dogm/status_screen_DOGM.cpp
Unescape Escape View File

@ -208,7 +208,7 @@ FORCE_INLINE void _draw_heater_status(const int8_t heater, const bool blink) {
if (PAGE_UNDER(7)) { if (PAGE_UNDER(7)) {
#if HEATER_IDLE_HANDLER #if HEATER_IDLE_HANDLER
const bool is_idle = IFBED(thermalManager.is_bed_idle(), thermalManager.is_heater_idle(heater)), const bool is_idle = IFBED(thermalManager.bed_idle.timed_out, thermalManager.hotend_idle[heater].timed_out),
dodraw = (blink || !is_idle); dodraw = (blink || !is_idle);
#else #else
constexpr bool dodraw = true; constexpr bool dodraw = true;

2
Marlin/src/lcd/dogm/ultralcd_DOGM.cpp
Unescape Escape View File

@ -261,7 +261,7 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop
lcd_put_u8str(i16tostr3(thermalManager.degHotend(extruder))); lcd_put_u8str(i16tostr3(thermalManager.degHotend(extruder)));
lcd_put_wchar('/'); lcd_put_wchar('/');
if (get_blink() || !thermalManager.is_heater_idle(extruder)) if (get_blink() || !thermalManager.hotend_idle[extruder].timed_out)
lcd_put_u8str(i16tostr3(thermalManager.degTargetHotend(extruder))); lcd_put_u8str(i16tostr3(thermalManager.degTargetHotend(extruder)));
} }

9
Marlin/src/lcd/language/language_en.h
Unescape Escape View File

@ -537,6 +537,9 @@
#ifndef MSG_BED #ifndef MSG_BED
#define MSG_BED _UxGT("Bed") #define MSG_BED _UxGT("Bed")
#endif #endif
#ifndef MSG_CHAMBER
#define MSG_CHAMBER _UxGT("Enclosure")
#endif
#ifndef MSG_FAN_SPEED #ifndef MSG_FAN_SPEED
#define MSG_FAN_SPEED _UxGT("Fan speed") #define MSG_FAN_SPEED _UxGT("Fan speed")
#endif #endif
@ -921,6 +924,12 @@
#ifndef MSG_ERR_MINTEMP_BED #ifndef MSG_ERR_MINTEMP_BED
#define MSG_ERR_MINTEMP_BED _UxGT("Err: MINTEMP BED") #define MSG_ERR_MINTEMP_BED _UxGT("Err: MINTEMP BED")
#endif #endif
#ifndef MSG_ERR_MAXTEMP_CHAMBER
#define MSG_ERR_MAXTEMP_CHAMBER _UxGT("Err: MAXTEMP CHAMBER")
#endif
#ifndef MSG_ERR_MINTEMP_CHAMBER
#define MSG_ERR_MINTEMP_CHAMBER _UxGT("Err: MINTEMP CHAMBER")
#endif
#ifndef MSG_ERR_Z_HOMING #ifndef MSG_ERR_Z_HOMING
#define MSG_ERR_Z_HOMING MSG_HOME _UxGT(" ") MSG_X MSG_Y _UxGT(" ") MSG_FIRST #define MSG_ERR_Z_HOMING MSG_HOME _UxGT(" ") MSG_X MSG_Y _UxGT(" ") MSG_FIRST
#endif #endif

35
Marlin/src/lcd/menu/menu.cpp
Unescape Escape View File

@ -37,7 +37,7 @@
#include "../../module/configuration_store.h" #include "../../module/configuration_store.h"
#endif #endif
#if WATCH_HOTENDS || WATCH_THE_BED || ENABLED(BABYSTEP_ZPROBE_OFFSET) #if WATCH_HOTENDS || WATCH_BED || ENABLED(BABYSTEP_ZPROBE_OFFSET)
#include "../../module/temperature.h" #include "../../module/temperature.h"
#endif #endif
@ -405,39 +405,6 @@ void MarlinUI::completion_feedback(const bool good/*=true*/) {
#endif // BABYSTEP_ZPROBE_OFFSET #endif // BABYSTEP_ZPROBE_OFFSET
/**
* Watch temperature callbacks
*/
#if HAS_TEMP_HOTEND
#if WATCH_HOTENDS
#define _WATCH_FUNC(N) thermalManager.start_watching_heater(N)
#else
#define _WATCH_FUNC(N) NOOP
#endif
void watch_temp_callback_E0() { _WATCH_FUNC(0); }
#if HOTENDS > 1
void watch_temp_callback_E1() { _WATCH_FUNC(1); }
#if HOTENDS > 2
void watch_temp_callback_E2() { _WATCH_FUNC(2); }
#if HOTENDS > 3
void watch_temp_callback_E3() { _WATCH_FUNC(3); }
#if HOTENDS > 4
void watch_temp_callback_E4() { _WATCH_FUNC(4); }
#if HOTENDS > 5
void watch_temp_callback_E5() { _WATCH_FUNC(5); }
#endif // HOTENDS > 5
#endif // HOTENDS > 4
#endif // HOTENDS > 3
#endif // HOTENDS > 2
#endif // HOTENDS > 1
#endif // HAS_TEMP_HOTEND
void watch_temp_callback_bed() {
#if WATCH_THE_BED
thermalManager.start_watching_bed();
#endif
}
#if ENABLED(AUTO_BED_LEVELING_UBL) || ENABLED(PID_AUTOTUNE_MENU) || ENABLED(ADVANCED_PAUSE_FEATURE) #if ENABLED(AUTO_BED_LEVELING_UBL) || ENABLED(PID_AUTOTUNE_MENU) || ENABLED(ADVANCED_PAUSE_FEATURE)
void lcd_enqueue_command(const char * const cmd) { void lcd_enqueue_command(const char * const cmd) {

8
Marlin/src/lcd/menu/menu.h
Unescape Escape View File

@ -340,14 +340,6 @@ void menu_move();
void lcd_move_z(); void lcd_move_z();
void _lcd_draw_homing(); void _lcd_draw_homing();
void watch_temp_callback_E0();
void watch_temp_callback_E1();
void watch_temp_callback_E2();
void watch_temp_callback_E3();
void watch_temp_callback_E4();
void watch_temp_callback_E5();
void watch_temp_callback_bed();
#define HAS_LINE_TO_Z (ENABLED(DELTA) || ENABLED(PROBE_MANUALLY) || ENABLED(MESH_BED_LEVELING) || ENABLED(LEVEL_BED_CORNERS)) #define HAS_LINE_TO_Z (ENABLED(DELTA) || ENABLED(PROBE_MANUALLY) || ENABLED(MESH_BED_LEVELING) || ENABLED(LEVEL_BED_CORNERS))
#if HAS_LINE_TO_Z #if HAS_LINE_TO_Z

4
Marlin/src/lcd/menu/menu_filament.cpp
Unescape Escape View File

@ -61,7 +61,7 @@ static void _change_filament_temp(const uint16_t temperature) {
} }
inline void _lcd_change_filament_temp_1_func() { _change_filament_temp(ui.preheat_hotend_temp[0]); } inline void _lcd_change_filament_temp_1_func() { _change_filament_temp(ui.preheat_hotend_temp[0]); }
inline void _lcd_change_filament_temp_2_func() { _change_filament_temp(ui.preheat_hotend_temp[1]); } inline void _lcd_change_filament_temp_2_func() { _change_filament_temp(ui.preheat_hotend_temp[1]); }
inline void _lcd_change_filament_temp_custom_cb() { _change_filament_temp(thermalManager.target_temperature[_change_filament_temp_extruder]); } inline void _lcd_change_filament_temp_custom_cb() { _change_filament_temp(thermalManager.temp_hotend[_change_filament_temp_extruder].target); }
static PGM_P change_filament_header(const AdvancedPauseMode mode) { static PGM_P change_filament_header(const AdvancedPauseMode mode) {
switch (mode) { switch (mode) {
@ -101,7 +101,7 @@ void _menu_temp_filament_op(const AdvancedPauseMode mode, const int8_t extruder)
#endif #endif
#endif #endif
} }
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_PREHEAT_CUSTOM, &thermalManager.target_temperature[_change_filament_temp_extruder], EXTRUDE_MINTEMP, max_temp - 15, _lcd_change_filament_temp_custom_cb); MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_PREHEAT_CUSTOM, &thermalManager.temp_hotend[_change_filament_temp_extruder].target, EXTRUDE_MINTEMP, max_temp - 15, _lcd_change_filament_temp_custom_cb);
END_MENU(); END_MENU();
} }
#if E_STEPPERS #if E_STEPPERS

17
Marlin/src/lcd/menu/menu_temperature.cpp
Unescape Escape View File

@ -353,9 +353,9 @@ void menu_temperature() {
// Nozzle [1-5]: // Nozzle [1-5]:
// //
#if HOTENDS == 1 #if HOTENDS == 1
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0); MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.temp_hotend[0].target, 0, HEATER_0_MAXTEMP - 15, thermalManager.start_watching_E0);
#else // HOTENDS > 1 #else // HOTENDS > 1
#define EDIT_TARGET(N) MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_LCD_N##N, &thermalManager.target_temperature[N], 0, HEATER_##N##_MAXTEMP - 15, watch_temp_callback_E##N) #define EDIT_TARGET(N) MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_LCD_N##N, &thermalManager.temp_hotend[N].target, 0, HEATER_##N##_MAXTEMP - 15, thermalManager.start_watching_E##N)
EDIT_TARGET(0); EDIT_TARGET(0);
EDIT_TARGET(1); EDIT_TARGET(1);
#if HOTENDS > 2 #if HOTENDS > 2
@ -380,7 +380,14 @@ void menu_temperature() {
// Bed: // Bed:
// //
#if HAS_HEATED_BED #if HAS_HEATED_BED
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_BED, &thermalManager.target_temperature_bed, 0, BED_MAXTEMP - 15, watch_temp_callback_bed); MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_BED, &thermalManager.temp_bed.target, 0, BED_MAXTEMP - 5, thermalManager.start_watching_bed);
#endif
//
// Chamber:
//
#if HAS_HEATED_CHAMBER
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_CHAMBER, &thermalManager.temp_chamber.target, 0, CHAMBER_MAXTEMP - 5, thermalManager.start_watching_chamber);
#endif #endif
// //
@ -413,9 +420,9 @@ void menu_temperature() {
// Cooldown // Cooldown
// //
bool has_heat = false; bool has_heat = false;
HOTEND_LOOP() if (thermalManager.target_temperature[HOTEND_INDEX]) { has_heat = true; break; } HOTEND_LOOP() if (thermalManager.temp_hotend[HOTEND_INDEX].target) { has_heat = true; break; }
#if HAS_TEMP_BED #if HAS_TEMP_BED
if (thermalManager.target_temperature_bed) has_heat = true; if (thermalManager.temp_bed.target) has_heat = true;
#endif #endif
if (has_heat) MENU_ITEM(function, MSG_COOLDOWN, lcd_cooldown); if (has_heat) MENU_ITEM(function, MSG_COOLDOWN, lcd_cooldown);

6
Marlin/src/lcd/menu/menu_tune.cpp
Unescape Escape View File

@ -116,9 +116,9 @@ void menu_tune() {
// Nozzle [1-4]: // Nozzle [1-4]:
// //
#if HOTENDS == 1 #if HOTENDS == 1
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.target_temperature[0], 0, HEATER_0_MAXTEMP - 15, watch_temp_callback_E0); MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE, &thermalManager.temp_hotend[0].target, 0, HEATER_0_MAXTEMP - 15, thermalManager.start_watching_E0);
#else // HOTENDS > 1 #else // HOTENDS > 1
#define EDIT_NOZZLE(N) MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_LCD_N##N, &thermalManager.target_temperature[N], 0, HEATER_##N##_MAXTEMP - 15, watch_temp_callback_E##N) #define EDIT_NOZZLE(N) MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_NOZZLE MSG_LCD_N##N, &thermalManager.temp_hotend[N].target, 0, HEATER_##N##_MAXTEMP - 15, thermalManager.start_watching_E##N)
EDIT_NOZZLE(0); EDIT_NOZZLE(0);
EDIT_NOZZLE(1); EDIT_NOZZLE(1);
#if HOTENDS > 2 #if HOTENDS > 2
@ -143,7 +143,7 @@ void menu_tune() {
// Bed: // Bed:
// //
#if HAS_HEATED_BED #if HAS_HEATED_BED
MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_BED, &thermalManager.target_temperature_bed, 0, BED_MAXTEMP - 15, watch_temp_callback_bed); MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(int3, MSG_BED, &thermalManager.temp_bed.target, 0, BED_MAXTEMP - 15, thermalManager.start_watching_bed);
#endif #endif
// //

16
Marlin/src/module/configuration_store.cpp
Unescape Escape View File

@ -728,7 +728,7 @@ void MarlinSettings::postprocess() {
const PID_t bed_pid = { DUMMY_PID_VALUE, DUMMY_PID_VALUE, DUMMY_PID_VALUE }; const PID_t bed_pid = { DUMMY_PID_VALUE, DUMMY_PID_VALUE, DUMMY_PID_VALUE };
EEPROM_WRITE(bed_pid); EEPROM_WRITE(bed_pid);
#else #else
EEPROM_WRITE(thermalManager.bed_pid); EEPROM_WRITE(thermalManager.temp_bed.pid);
#endif #endif
} }
@ -1448,7 +1448,7 @@ void MarlinSettings::postprocess() {
EEPROM_READ(pid); EEPROM_READ(pid);
#if ENABLED(PIDTEMPBED) #if ENABLED(PIDTEMPBED)
if (!validating && pid.Kp != DUMMY_PID_VALUE) if (!validating && pid.Kp != DUMMY_PID_VALUE)
memcpy(&thermalManager.bed_pid, &pid, sizeof(pid)); memcpy(&thermalManager.temp_bed.pid, &pid, sizeof(pid));
#endif #endif
} }
@ -2181,9 +2181,9 @@ void MarlinSettings::reset() {
// //
#if ENABLED(PIDTEMPBED) #if ENABLED(PIDTEMPBED)
thermalManager.bed_pid.Kp = DEFAULT_bedKp; thermalManager.temp_bed.pid.Kp = DEFAULT_bedKp;
thermalManager.bed_pid.Ki = scalePID_i(DEFAULT_bedKi); thermalManager.temp_bed.pid.Ki = scalePID_i(DEFAULT_bedKi);
thermalManager.bed_pid.Kd = scalePID_d(DEFAULT_bedKd); thermalManager.temp_bed.pid.Kd = scalePID_d(DEFAULT_bedKd);
#endif #endif
// //
@ -2726,9 +2726,9 @@ void MarlinSettings::reset() {
#if ENABLED(PIDTEMPBED) #if ENABLED(PIDTEMPBED)
CONFIG_ECHO_START(); CONFIG_ECHO_START();
SERIAL_ECHOLNPAIR( SERIAL_ECHOLNPAIR(
" M304 P", thermalManager.bed_pid.Kp " M304 P", thermalManager.temp_bed.pid.Kp
, " I", unscalePID_i(thermalManager.bed_pid.Ki) , " I", unscalePID_i(thermalManager.temp_bed.pid.Ki)
, " D", unscalePID_d(thermalManager.bed_pid.Kd) , " D", unscalePID_d(thermalManager.temp_bed.pid.Kd)
); );
#endif #endif

833
Marlin/src/module/temperature.cpp
View File

File diff suppressed because it is too large Load Diff

403
Marlin/src/module/temperature.h
Unescape Escape View File

@ -36,10 +36,12 @@
#define SOFT_PWM_SCALE 0 #define SOFT_PWM_SCALE 0
#endif #endif
#if HOTENDS == 1 #if HOTENDS <= 1
#define HOTEND_INDEX 0 #define HOTEND_INDEX 0
#define E_UNUSED() UNUSED(e)
#else #else
#define HOTEND_INDEX e #define HOTEND_INDEX e
#define E_UNUSED()
#endif #endif
// PID storage // PID storage
@ -47,6 +49,11 @@ typedef struct { float Kp, Ki, Kd; } PID_t;
typedef struct { float Kp, Ki, Kd, Kc; } PIDC_t; typedef struct { float Kp, Ki, Kd, Kc; } PIDC_t;
#if ENABLED(PID_EXTRUSION_SCALING) #if ENABLED(PID_EXTRUSION_SCALING)
typedef PIDC_t hotend_pid_t; typedef PIDC_t hotend_pid_t;
#if LPQ_MAX_LEN > 255
typedef uint16_t lpq_ptr_t;
#else
typedef uint8_t lpq_ptr_t;
#endif
#else #else
typedef PID_t hotend_pid_t; typedef PID_t hotend_pid_t;
#endif #endif
@ -54,11 +61,11 @@ typedef struct { float Kp, Ki, Kd, Kc; } PIDC_t;
#define DUMMY_PID_VALUE 3000.0f #define DUMMY_PID_VALUE 3000.0f
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
#define _PID_Kp(H) Temperature::pid[H].Kp #define _PID_Kp(H) Temperature::temp_hotend[H].pid.Kp
#define _PID_Ki(H) Temperature::pid[H].Ki #define _PID_Ki(H) Temperature::temp_hotend[H].pid.Ki
#define _PID_Kd(H) Temperature::pid[H].Kd #define _PID_Kd(H) Temperature::temp_hotend[H].pid.Kd
#if ENABLED(PID_EXTRUSION_SCALING) #if ENABLED(PID_EXTRUSION_SCALING)
#define _PID_Kc(H) Temperature::pid[H].Kc #define _PID_Kc(H) Temperature::temp_hotend[H].pid.Kc
#else #else
#define _PID_Kc(H) 1 #define _PID_Kc(H) 1
#endif #endif
@ -80,6 +87,14 @@ enum ADCSensorState : char {
PrepareTemp_0, PrepareTemp_0,
MeasureTemp_0, MeasureTemp_0,
#endif #endif
#if HAS_HEATED_BED
PrepareTemp_BED,
MeasureTemp_BED,
#endif
#if HAS_TEMP_CHAMBER
PrepareTemp_CHAMBER,
MeasureTemp_CHAMBER,
#endif
#if HAS_TEMP_ADC_1 #if HAS_TEMP_ADC_1
PrepareTemp_1, PrepareTemp_1,
MeasureTemp_1, MeasureTemp_1,
@ -96,13 +111,9 @@ enum ADCSensorState : char {
PrepareTemp_4, PrepareTemp_4,
MeasureTemp_4, MeasureTemp_4,
#endif #endif
#if HAS_HEATED_BED #if HAS_TEMP_ADC_5
PrepareTemp_BED, PrepareTemp_5,
MeasureTemp_BED, MeasureTemp_5,
#endif
#if HAS_TEMP_CHAMBER
PrepareTemp_CHAMBER,
MeasureTemp_CHAMBER,
#endif #endif
#if ENABLED(FILAMENT_WIDTH_SENSOR) #if ENABLED(FILAMENT_WIDTH_SENSOR)
Prepare_FILWIDTH, Prepare_FILWIDTH,
@ -136,16 +147,115 @@ enum ADCSensorState : char {
#define G26_CLICK_CAN_CANCEL (HAS_LCD_MENU && ENABLED(G26_MESH_VALIDATION)) #define G26_CLICK_CAN_CANCEL (HAS_LCD_MENU && ENABLED(G26_MESH_VALIDATION))
enum TempIndex : uint8_t {
#if HOTENDS > 0
TEMP_E0,
#if HOTENDS > 1
TEMP_E1,
#if HOTENDS > 2
TEMP_E2,
#if HOTENDS > 3
TEMP_E3,
#if HOTENDS > 4
TEMP_E4,
#if HOTENDS > 5
TEMP_E5,
#endif
#endif
#endif
#endif
#endif
#endif
#if HAS_HEATED_BED
TEMP_BED,
#endif
#if HAS_HEATED_CHAMBER
TEMP_CHAMBER,
#endif
tempCOUNT
};
// A temperature sensor
typedef struct TempInfo {
uint16_t acc;
int16_t raw;
float current;
} temp_info_t;
// A PWM heater with temperature sensor
typedef struct HeaterInfo : public TempInfo {
int16_t target;
uint8_t soft_pwm_amount;
} heater_info_t;
// A heater with PID stabilization
template<typename T>
struct PIDHeaterInfo : public HeaterInfo {
T pid; // Initialized by settings.load()
};
#if ENABLED(PIDTEMP)
typedef struct PIDHeaterInfo<hotend_pid_t> hotend_info_t;
#else
typedef heater_info_t hotend_info_t;
#endif
#if HAS_HEATED_BED
#if ENABLED(PIDTEMPBED)
typedef struct PIDHeaterInfo<PID_t> bed_info_t;
#else
typedef heater_info_t bed_info_t;
#endif
#endif
#if HAS_TEMP_CHAMBER
#if HAS_HEATED_CHAMBER
#if ENABLED(PIDTEMPCHAMBER)
typedef struct PIDHeaterInfo<PID_t> chamber_info_t;
#else
typedef heater_info_t chamber_info_t;
#endif
#else
typedef temp_info_t chamber_info_t;
#endif
#endif
// Heater idle handling
typedef struct {
millis_t timeout_ms;
bool timed_out;
inline void update(const millis_t &ms) { if (!timed_out && timeout_ms && ELAPSED(ms, timeout_ms)) timed_out = true; }
inline void start(const millis_t &ms) { timeout_ms = millis() + ms; timed_out = false; }
inline void reset() { timeout_ms = 0; timed_out = false; }
inline void expire() { start(0); }
} heater_idle_t;
// Heater watch handling
typedef struct {
uint16_t target;
millis_t next_ms;
inline bool elapsed(const millis_t &ms) { return next_ms && ELAPSED(ms, next_ms); }
inline bool elapsed() { return elapsed(millis()); }
} heater_watch_t;
// Temperature sensor read value ranges
typedef struct { int16_t raw_min, raw_max; } raw_range_t;
typedef struct { int16_t mintemp, maxtemp; } celsius_range_t;
typedef struct { int16_t raw_min, raw_max, mintemp, maxtemp; } temp_range_t;
class Temperature { class Temperature {
public: public:
static volatile bool in_temp_isr; static volatile bool in_temp_isr;
static float current_temperature[HOTENDS]; static hotend_info_t temp_hotend[HOTENDS];
static int16_t current_temperature_raw[HOTENDS],
target_temperature[HOTENDS]; #if HAS_HEATED_BED
static uint8_t soft_pwm_amount[HOTENDS]; static bed_info_t temp_bed;
#endif
#if HAS_TEMP_CHAMBER
static chamber_info_t temp_chamber;
#endif
#if ENABLED(AUTO_POWER_E_FANS) #if ENABLED(AUTO_POWER_E_FANS)
static uint8_t autofan_speed[HOTENDS]; static uint8_t autofan_speed[HOTENDS];
@ -156,19 +266,6 @@ class Temperature {
soft_pwm_count_fan[FAN_COUNT]; soft_pwm_count_fan[FAN_COUNT];
#endif #endif
#if ENABLED(PIDTEMP)
static hotend_pid_t pid[HOTENDS];
#endif
#if HAS_HEATED_BED
static float current_temperature_bed;
static int16_t current_temperature_bed_raw, target_temperature_bed;
static uint8_t soft_pwm_amount_bed;
#if ENABLED(PIDTEMPBED)
static PID_t bed_pid;
#endif
#endif
#if ENABLED(BABYSTEPPING) #if ENABLED(BABYSTEPPING)
static volatile int16_t babystepsTodo[3]; static volatile int16_t babystepsTodo[3];
#endif #endif
@ -178,15 +275,11 @@ class Temperature {
static int16_t extrude_min_temp; static int16_t extrude_min_temp;
FORCE_INLINE static bool tooCold(const int16_t temp) { return allow_cold_extrude ? false : temp < extrude_min_temp; } FORCE_INLINE static bool tooCold(const int16_t temp) { return allow_cold_extrude ? false : temp < extrude_min_temp; }
FORCE_INLINE static bool tooColdToExtrude(const uint8_t e) { FORCE_INLINE static bool tooColdToExtrude(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e);
#endif
return tooCold(degHotend(HOTEND_INDEX)); return tooCold(degHotend(HOTEND_INDEX));
} }
FORCE_INLINE static bool targetTooColdToExtrude(const uint8_t e) { FORCE_INLINE static bool targetTooColdToExtrude(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e);
#endif
return tooCold(degTargetHotend(HOTEND_INDEX)); return tooCold(degTargetHotend(HOTEND_INDEX));
} }
#else #else
@ -197,6 +290,16 @@ class Temperature {
FORCE_INLINE static bool hotEnoughToExtrude(const uint8_t e) { return !tooColdToExtrude(e); } FORCE_INLINE static bool hotEnoughToExtrude(const uint8_t e) { return !tooColdToExtrude(e); }
FORCE_INLINE static bool targetHotEnoughToExtrude(const uint8_t e) { return !targetTooColdToExtrude(e); } FORCE_INLINE static bool targetHotEnoughToExtrude(const uint8_t e) { return !targetTooColdToExtrude(e); }
#if HEATER_IDLE_HANDLER
static heater_idle_t hotend_idle[HOTENDS];
#if HAS_HEATED_BED
static heater_idle_t bed_idle;
#endif
#if HAS_HEATED_CHAMBER
static heater_idle_t chamber_idle;
#endif
#endif
private: private:
#if EARLY_WATCHDOG #if EARLY_WATCHDOG
@ -204,11 +307,9 @@ class Temperature {
#endif #endif
static volatile bool temp_meas_ready; static volatile bool temp_meas_ready;
static uint16_t raw_temp_value[MAX_EXTRUDERS];
#if WATCH_HOTENDS #if WATCH_HOTENDS
static uint16_t watch_target_temp[HOTENDS]; static heater_watch_t watch_hotend[HOTENDS];
static millis_t watch_heater_next_ms[HOTENDS];
#endif #endif
#if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT) #if ENABLED(TEMP_SENSOR_1_AS_REDUNDANT)
@ -217,42 +318,40 @@ class Temperature {
#endif #endif
#if ENABLED(PID_EXTRUSION_SCALING) #if ENABLED(PID_EXTRUSION_SCALING)
static long last_e_position; static int32_t last_e_position, lpq[LPQ_MAX_LEN];
static long lpq[LPQ_MAX_LEN]; static lpq_ptr_t lpq_ptr;
static int lpq_ptr;
#endif #endif
// Init min and max temp with extreme values to prevent false errors during startup static temp_range_t temp_range[HOTENDS];
static int16_t minttemp_raw[HOTENDS],
maxttemp_raw[HOTENDS],
minttemp[HOTENDS],
maxttemp[HOTENDS];
#if HAS_HEATED_BED #if HAS_HEATED_BED
static uint16_t raw_temp_bed_value; #if WATCH_BED
#if WATCH_THE_BED static heater_watch_t watch_bed;
static uint16_t watch_target_bed_temp;
static millis_t watch_bed_next_ms;
#endif #endif
#if DISABLED(PIDTEMPBED) #if DISABLED(PIDTEMPBED)
static millis_t next_bed_check_ms; static millis_t next_bed_check_ms;
#endif #endif
#if HEATER_IDLE_HANDLER
static millis_t bed_idle_timeout_ms;
static bool bed_idle_timeout_exceeded;
#endif
#ifdef BED_MINTEMP #ifdef BED_MINTEMP
static int16_t bed_minttemp_raw; static int16_t mintemp_raw_BED;
#endif #endif
#ifdef BED_MAXTEMP #ifdef BED_MAXTEMP
static int16_t bed_maxttemp_raw; static int16_t maxtemp_raw_BED;
#endif #endif
#endif #endif
#if HAS_TEMP_CHAMBER #if HAS_HEATED_CHAMBER
static uint16_t raw_temp_chamber_value; #if WATCH_CHAMBER
static float current_temperature_chamber; static heater_watch_t watch_chamber;
static int16_t current_temperature_chamber_raw; #endif
#if DISABLED(PIDTEMPCHAMBER)
static millis_t next_chamber_check_ms;
#endif
#ifdef CHAMBER_MINTEMP
static int16_t mintemp_raw_CHAMBER;
#endif
#ifdef CHAMBER_MAXTEMP
static int16_t maxtemp_raw_CHAMBER;
#endif
#endif #endif
#ifdef MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED #ifdef MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED
@ -279,11 +378,6 @@ class Temperature {
static bool paused; static bool paused;
#endif #endif
#if HEATER_IDLE_HANDLER
static millis_t heater_idle_timeout_ms[HOTENDS];
static bool heater_idle_timeout_exceeded[HOTENDS];
#endif
public: public:
#if HAS_ADC_BUTTONS #if HAS_ADC_BUTTONS
static uint32_t current_ADCKey_raw; static uint32_t current_ADCKey_raw;
@ -311,7 +405,7 @@ class Temperature {
static float analog_to_celsius_bed(const int raw); static float analog_to_celsius_bed(const int raw);
#endif #endif
#if HAS_TEMP_CHAMBER #if HAS_TEMP_CHAMBER
static float analog_to_celsiusChamber(const int raw); static float analog_to_celsius_chamber(const int raw);
#endif #endif
#if FAN_COUNT > 0 #if FAN_COUNT > 0
@ -395,21 +489,15 @@ class Temperature {
*/ */
#ifdef MILLISECONDS_PREHEAT_TIME #ifdef MILLISECONDS_PREHEAT_TIME
static bool is_preheating(const uint8_t e) { static bool is_preheating(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e);
#endif
return preheat_end_time[HOTEND_INDEX] && PENDING(millis(), preheat_end_time[HOTEND_INDEX]); return preheat_end_time[HOTEND_INDEX] && PENDING(millis(), preheat_end_time[HOTEND_INDEX]);
} }
static void start_preheat_time(const uint8_t e) { static void start_preheat_time(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e);
#endif
preheat_end_time[HOTEND_INDEX] = millis() + MILLISECONDS_PREHEAT_TIME; preheat_end_time[HOTEND_INDEX] = millis() + MILLISECONDS_PREHEAT_TIME;
} }
static void reset_preheat_time(const uint8_t e) { static void reset_preheat_time(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e);
#endif
preheat_end_time[HOTEND_INDEX] = 0; preheat_end_time[HOTEND_INDEX] = 0;
} }
#else #else
@ -427,63 +515,81 @@ class Temperature {
//deg=degreeCelsius //deg=degreeCelsius
FORCE_INLINE static float degHotend(const uint8_t e) { FORCE_INLINE static float degHotend(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e); return temp_hotend[HOTEND_INDEX].current;
#endif
return current_temperature[HOTEND_INDEX];
} }
#if ENABLED(SHOW_TEMP_ADC_VALUES) #if ENABLED(SHOW_TEMP_ADC_VALUES)
FORCE_INLINE static int16_t rawHotendTemp(const uint8_t e) { FORCE_INLINE static int16_t rawHotendTemp(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e); return temp_hotend[HOTEND_INDEX].raw;
#endif
return current_temperature_raw[HOTEND_INDEX];
} }
#endif #endif
FORCE_INLINE static int16_t degTargetHotend(const uint8_t e) { FORCE_INLINE static int16_t degTargetHotend(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e); return temp_hotend[HOTEND_INDEX].target;
#endif
return target_temperature[HOTEND_INDEX];
} }
#if WATCH_HOTENDS #if WATCH_HOTENDS
static void start_watching_heater(const uint8_t e=0); static void start_watching_heater(const uint8_t e=0);
#else
static inline void start_watching_heater(const uint8_t e=0) { UNUSED(e); }
#endif #endif
static void setTargetHotend(const int16_t celsius, const uint8_t e) { #if HAS_LCD_MENU
#if HOTENDS == 1 static inline void start_watching_E0() { start_watching_heater(0); }
UNUSED(e); static inline void start_watching_E1() { start_watching_heater(1); }
static inline void start_watching_E2() { start_watching_heater(2); }
static inline void start_watching_E3() { start_watching_heater(3); }
static inline void start_watching_E4() { start_watching_heater(4); }
static inline void start_watching_E5() { start_watching_heater(5); }
#endif #endif
static void setTargetHotend(const int16_t celsius, const uint8_t e) {
E_UNUSED();
#ifdef MILLISECONDS_PREHEAT_TIME #ifdef MILLISECONDS_PREHEAT_TIME
if (celsius == 0) if (celsius == 0)
reset_preheat_time(HOTEND_INDEX); reset_preheat_time(HOTEND_INDEX);
else if (target_temperature[HOTEND_INDEX] == 0) else if (temp_hotend[HOTEND_INDEX].target == 0)
start_preheat_time(HOTEND_INDEX); start_preheat_time(HOTEND_INDEX);
#endif #endif
#if ENABLED(AUTO_POWER_CONTROL) #if ENABLED(AUTO_POWER_CONTROL)
powerManager.power_on(); powerManager.power_on();
#endif #endif
target_temperature[HOTEND_INDEX] = MIN(celsius, maxttemp[HOTEND_INDEX] - 15); temp_hotend[HOTEND_INDEX].target = MIN(celsius, temp_range[HOTEND_INDEX].maxtemp - 15);
#if WATCH_HOTENDS
start_watching_heater(HOTEND_INDEX); start_watching_heater(HOTEND_INDEX);
}
#if WATCH_CHAMBER
static void start_watching_chamber();
#else
static inline void start_watching_chamber() {}
#endif #endif
#if HAS_TEMP_CHAMBER
static void setTargetChamber(const int16_t celsius) {
#if HAS_HEATED_CHAMBER
temp_chamber.target =
#ifdef CHAMBER_MAXTEMP
min(celsius, CHAMBER_MAXTEMP)
#else
celsius
#endif
;
start_watching_chamber();
#endif // HAS_HEATED_CHAMBER
} }
#endif // HAS_TEMP_CHAMBER
FORCE_INLINE static bool isHeatingHotend(const uint8_t e) { FORCE_INLINE static bool isHeatingHotend(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e); return temp_hotend[HOTEND_INDEX].target > temp_hotend[HOTEND_INDEX].current;
#endif
return target_temperature[HOTEND_INDEX] > current_temperature[HOTEND_INDEX];
} }
FORCE_INLINE static bool isCoolingHotend(const uint8_t e) { FORCE_INLINE static bool isCoolingHotend(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e); return temp_hotend[HOTEND_INDEX].target < temp_hotend[HOTEND_INDEX].current;
#endif
return target_temperature[HOTEND_INDEX] < current_temperature[HOTEND_INDEX];
} }
#if HAS_TEMP_HOTEND #if HAS_TEMP_HOTEND
@ -497,33 +603,33 @@ class Temperature {
#if HAS_HEATED_BED #if HAS_HEATED_BED
#if ENABLED(SHOW_TEMP_ADC_VALUES) #if ENABLED(SHOW_TEMP_ADC_VALUES)
FORCE_INLINE static int16_t rawBedTemp() { return current_temperature_bed_raw; } FORCE_INLINE static int16_t rawBedTemp() { return temp_bed.raw; }
#endif
FORCE_INLINE static float degBed() { return temp_bed.current; }
FORCE_INLINE static int16_t degTargetBed() { return temp_bed.target; }
FORCE_INLINE static bool isHeatingBed() { return temp_bed.target > temp_bed.current; }
FORCE_INLINE static bool isCoolingBed() { return temp_bed.target < temp_bed.current; }
#if WATCH_BED
static void start_watching_bed();
#else
static inline void start_watching_bed() {}
#endif #endif
FORCE_INLINE static float degBed() { return current_temperature_bed; }
FORCE_INLINE static int16_t degTargetBed() { return target_temperature_bed; }
FORCE_INLINE static bool isHeatingBed() { return target_temperature_bed > current_temperature_bed; }
FORCE_INLINE static bool isCoolingBed() { return target_temperature_bed < current_temperature_bed; }
static void setTargetBed(const int16_t celsius) { static void setTargetBed(const int16_t celsius) {
#if ENABLED(AUTO_POWER_CONTROL) #if ENABLED(AUTO_POWER_CONTROL)
powerManager.power_on(); powerManager.power_on();
#endif #endif
target_temperature_bed = temp_bed.target =
#ifdef BED_MAXTEMP #ifdef BED_MAXTEMP
MIN(celsius, BED_MAXTEMP - 15) MIN(celsius, BED_MAXTEMP - 15)
#else #else
celsius celsius
#endif #endif
; ;
#if WATCH_THE_BED
start_watching_bed(); start_watching_bed();
#endif
} }
#if WATCH_THE_BED
static void start_watching_bed();
#endif
static bool wait_for_bed(const bool no_wait_for_cooling=true static bool wait_for_bed(const bool no_wait_for_cooling=true
#if G26_CLICK_CAN_CANCEL #if G26_CLICK_CAN_CANCEL
, const bool click_to_cancel=false , const bool click_to_cancel=false
@ -534,10 +640,15 @@ class Temperature {
#if HAS_TEMP_CHAMBER #if HAS_TEMP_CHAMBER
#if ENABLED(SHOW_TEMP_ADC_VALUES) #if ENABLED(SHOW_TEMP_ADC_VALUES)
FORCE_INLINE static int16_t rawChamberTemp() { return current_temperature_chamber_raw; } FORCE_INLINE static int16_t rawChamberTemp() { return temp_chamber.raw; }
#endif #endif
FORCE_INLINE static float degChamber() { return current_temperature_chamber; } FORCE_INLINE static float degChamber() { return temp_chambercurrent; }
#if HAS_HEATED_CHAMBER
FORCE_INLINE static bool isHeatingChamber() { return temp_chamber.target > temp_chambercurrent; }
FORCE_INLINE static bool isCoolingChamber() { return temp_chamber.target < temp_chambercurrent; }
FORCE_INLINE static int16_t degTargetChamber() {return temp_chamber.target; }
#endif #endif
#endif // HAS_TEMP_CHAMBER
FORCE_INLINE static bool still_heating(const uint8_t e) { FORCE_INLINE static bool still_heating(const uint8_t e) {
return degTargetHotend(e) > TEMP_HYSTERESIS && ABS(degHotend(e) - degTargetHotend(e)) > TEMP_HYSTERESIS; return degTargetHotend(e) > TEMP_HYSTERESIS && ABS(degHotend(e) - degTargetHotend(e)) > TEMP_HYSTERESIS;
@ -589,47 +700,17 @@ class Temperature {
#if HEATER_IDLE_HANDLER #if HEATER_IDLE_HANDLER
static void start_heater_idle_timer(const uint8_t e, const millis_t timeout_ms) {
#if HOTENDS == 1
UNUSED(e);
#endif
heater_idle_timeout_ms[HOTEND_INDEX] = millis() + timeout_ms;
heater_idle_timeout_exceeded[HOTEND_INDEX] = false;
}
static void reset_heater_idle_timer(const uint8_t e) { static void reset_heater_idle_timer(const uint8_t e) {
#if HOTENDS == 1 E_UNUSED();
UNUSED(e); hotend_idle[HOTEND_INDEX].reset();
#endif
heater_idle_timeout_ms[HOTEND_INDEX] = 0;
heater_idle_timeout_exceeded[HOTEND_INDEX] = false;
#if WATCH_HOTENDS
start_watching_heater(HOTEND_INDEX); start_watching_heater(HOTEND_INDEX);
#endif
}
FORCE_INLINE static bool is_heater_idle(const uint8_t e) {
#if HOTENDS == 1
UNUSED(e);
#endif
return heater_idle_timeout_exceeded[HOTEND_INDEX];
} }
#if HAS_HEATED_BED #if HAS_HEATED_BED
static void start_bed_idle_timer(const millis_t timeout_ms) {
bed_idle_timeout_ms = millis() + timeout_ms;
bed_idle_timeout_exceeded = false;
}
static void reset_bed_idle_timer() { static void reset_bed_idle_timer() {
bed_idle_timeout_ms = 0; bed_idle.reset();
bed_idle_timeout_exceeded = false;
#if WATCH_THE_BED
start_watching_bed(); start_watching_bed();
#endif
} }
FORCE_INLINE static bool is_bed_idle() { return bed_idle_timeout_exceeded; }
#endif #endif
#endif // HEATER_IDLE_HANDLER #endif // HEATER_IDLE_HANDLER
@ -689,25 +770,37 @@ class Temperature {
static float get_pid_output_bed(); static float get_pid_output_bed();
#endif #endif
#if HAS_HEATED_CHAMBER
static float get_pid_output_chamber();
#endif
static void _temp_error(const int8_t e, PGM_P const serial_msg, PGM_P const lcd_msg); static void _temp_error(const int8_t e, PGM_P const serial_msg, PGM_P const lcd_msg);
static void min_temp_error(const int8_t e); static void min_temp_error(const int8_t e);
static void max_temp_error(const int8_t e); static void max_temp_error(const int8_t e);
#if HAS_TEMP_CHAMBER
static void chamber_temp_error(const bool max);
#endif
#if ENABLED(THERMAL_PROTECTION_HOTENDS) || HAS_THERMALLY_PROTECTED_BED #if ENABLED(THERMAL_PROTECTION_HOTENDS) || HAS_THERMALLY_PROTECTED_BED || ENABLED(THERMAL_PROTECTION_CHAMBER)
enum TRState : char { TRInactive, TRFirstHeating, TRStable, TRRunaway }; enum TRState : char { TRInactive, TRFirstHeating, TRStable, TRRunaway };
static void thermal_runaway_protection(TRState * const state, millis_t * const timer, const float &current, const float &target, const int8_t heater_id, const uint16_t period_seconds, const uint16_t hysteresis_degc); typedef struct {
millis_t timer = 0;
TRState state = TRInactive;
} tr_state_machine_t;
#if ENABLED(THERMAL_PROTECTION_HOTENDS) #if ENABLED(THERMAL_PROTECTION_HOTENDS)
static TRState thermal_runaway_state_machine[HOTENDS]; static tr_state_machine_t tr_state_machine[HOTENDS];
static millis_t thermal_runaway_timer[HOTENDS];
#endif #endif
#if HAS_THERMALLY_PROTECTED_BED #if HAS_THERMALLY_PROTECTED_BED
static TRState thermal_runaway_bed_state_machine; static tr_state_machine_t tr_state_machine_bed;
static millis_t thermal_runaway_bed_timer;
#endif #endif
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
static tr_state_machine_t tr_state_machine_chamber;
#endif
static void thermal_runaway_protection(tr_state_machine_t &state, const float &current, const float &target, const int8_t heater_id, const uint16_t period_seconds, const uint16_t hysteresis_degc);
#endif // THERMAL_PROTECTION #endif // THERMAL_PROTECTION
}; };

4
Marlin/src/module/thermistor/thermistor_20.h
Unescape Escape View File

@ -43,6 +43,10 @@
#define HEATER_4_RAW_HI_TEMP 16383 #define HEATER_4_RAW_HI_TEMP 16383
#define HEATER_4_RAW_LO_TEMP 0 #define HEATER_4_RAW_LO_TEMP 0
#endif #endif
#if THERMISTORHEATER_5 == 20
#define HEATER_5_RAW_HI_TEMP 16383
#define HEATER_5_RAW_LO_TEMP 0
#endif
#if THERMISTORBED == 20 #if THERMISTORBED == 20
#define HEATER_BED_RAW_HI_TEMP 16383 #define HEATER_BED_RAW_HI_TEMP 16383
#define HEATER_BED_RAW_LO_TEMP 0 #define HEATER_BED_RAW_LO_TEMP 0

11
Marlin/src/module/thermistor/thermistors.h
Unescape Escape View File

@ -26,7 +26,7 @@
#define OVERSAMPLENR 16 #define OVERSAMPLENR 16
#define OV(N) int16_t((N) * (OVERSAMPLENR)) #define OV(N) int16_t((N) * (OVERSAMPLENR))
#define ANY_THERMISTOR_IS(n) (THERMISTORHEATER_0 == n || THERMISTORHEATER_1 == n || THERMISTORHEATER_2 == n || THERMISTORHEATER_3 == n || THERMISTORHEATER_4 == n || THERMISTORBED == n || THERMISTORCHAMBER == n) #define ANY_THERMISTOR_IS(n) (THERMISTORHEATER_0 == n || THERMISTORHEATER_1 == n || THERMISTORHEATER_2 == n || THERMISTORHEATER_3 == n || THERMISTORHEATER_4 == n || THERMISTORHEATER_5 == n || THERMISTORBED == n || THERMISTORCHAMBER == n)
// Pt1000 and Pt100 handling // Pt1000 and Pt100 handling
// //
@ -272,6 +272,15 @@ static_assert(HEATER_0_TEMPTABLE_LEN < 256 && HEATER_1_TEMPTABLE_LEN < 256 && HE
#define HEATER_4_RAW_LO_TEMP 0 #define HEATER_4_RAW_LO_TEMP 0
#endif #endif
#endif #endif
#ifndef HEATER_5_RAW_HI_TEMP
#ifdef HEATER_5_USES_THERMISTOR
#define HEATER_5_RAW_HI_TEMP 0
#define HEATER_5_RAW_LO_TEMP 16383
#else
#define HEATER_5_RAW_HI_TEMP 16383
#define HEATER_5_RAW_LO_TEMP 0
#endif
#endif
#ifndef HEATER_BED_RAW_HI_TEMP #ifndef HEATER_BED_RAW_HI_TEMP
#ifdef HEATER_BED_USES_THERMISTOR #ifdef HEATER_BED_USES_THERMISTOR
#define HEATER_BED_RAW_HI_TEMP 0 #define HEATER_BED_RAW_HI_TEMP 0

2
Marlin/src/module/tool_change.cpp
Unescape Escape View File

@ -838,7 +838,7 @@ void tool_change(const uint8_t tmp_extruder, const float fr_mm_s/*=0.0*/, bool n
thermalManager.fan_speed[0] = singlenozzle_fan_speed[tmp_extruder]; thermalManager.fan_speed[0] = singlenozzle_fan_speed[tmp_extruder];
#endif #endif
singlenozzle_temp[active_extruder] = thermalManager.target_temperature[0]; singlenozzle_temp[active_extruder] = thermalManager.temp_hotend[0].target;
if (singlenozzle_temp[tmp_extruder] && singlenozzle_temp[tmp_extruder] != singlenozzle_temp[active_extruder]) { if (singlenozzle_temp[tmp_extruder] && singlenozzle_temp[tmp_extruder] != singlenozzle_temp[active_extruder]) {
thermalManager.setTargetHotend(singlenozzle_temp[tmp_extruder], 0); thermalManager.setTargetHotend(singlenozzle_temp[tmp_extruder], 0);
#if ENABLED(ULTRA_LCD) || ENABLED(EXTENSIBLE_UI) #if ENABLED(ULTRA_LCD) || ENABLED(EXTENSIBLE_UI)

2
buildroot/share/tests/LPC1768-tests
Unescape Escape View File

@ -37,7 +37,7 @@ opt_set EXTRUDERS 2
opt_set TEMP_SENSOR_1 -1 opt_set TEMP_SENSOR_1 -1
opt_set TEMP_SENSOR_BED 5 opt_set TEMP_SENSOR_BED 5
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \ opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
FILAMENT_WIDTH_SENSOR FILAMENT_LCD_DISPLAY \ FILAMENT_WIDTH_SENSOR FILAMENT_LCD_DISPLAY PID_EXTRUSION_SCALING \
FIX_MOUNTED_PROBE Z_SAFE_HOMING AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \ FIX_MOUNTED_PROBE Z_SAFE_HOMING AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET BABYSTEP_ZPROBE_GFX_OVERLAY \ BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET BABYSTEP_ZPROBE_GFX_OVERLAY \
PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \ PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \

7
buildroot/share/tests/megaatmega2560-tests
Unescape Escape View File

@ -26,9 +26,10 @@ opt_set MOTHERBOARD BOARD_RAMPS_14_EEB
opt_set EXTRUDERS 2 opt_set EXTRUDERS 2
opt_set TEMP_SENSOR_0 -2 opt_set TEMP_SENSOR_0 -2
opt_set TEMP_SENSOR_1 1 opt_set TEMP_SENSOR_1 1
opt_set TEMP_SENSOR_BED 1 opt_set TEMP_SENSOR_BED 2
opt_set POWER_SUPPLY 1 opt_set POWER_SUPPLY 1
opt_set GRID_MAX_POINTS_X 16 opt_set GRID_MAX_POINTS_X 16
opt_set FANMUX0_PIN 53
opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING \ opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING \
SDSUPPORT EEPROM_SETTINGS REPRAP_DISCOUNT_SMART_CONTROLLER \ SDSUPPORT EEPROM_SETTINGS REPRAP_DISCOUNT_SMART_CONTROLLER \
BLINKM PCA9632 RGB_LED NEOPIXEL_LED AUTO_POWER_CONTROL \ BLINKM PCA9632 RGB_LED NEOPIXEL_LED AUTO_POWER_CONTROL \
@ -39,7 +40,9 @@ opt_enable PIDTEMPBED FIX_MOUNTED_PROBE Z_SAFE_HOMING \
POWER_LOSS_RECOVERY POWER_LOSS_PIN POWER_LOSS_STATE BINARY_FILE_TRANSFER \ POWER_LOSS_RECOVERY POWER_LOSS_PIN POWER_LOSS_STATE BINARY_FILE_TRANSFER \
LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST PINS_DEBUGGING \ LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST PINS_DEBUGGING \
MAX7219_DEBUG LED_CONTROL_MENU CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CODEPENDENT_XY_HOMING BACKLASH_COMPENSATION BACKLASH_GCODE MAX7219_DEBUG LED_CONTROL_MENU CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CODEPENDENT_XY_HOMING BACKLASH_COMPENSATION BACKLASH_GCODE
opt_set FANMUX0_PIN 53 opt_enable SLOW_PWM_HEATERS THERMAL_PROTECTION_CHAMBER
opt_set TEMP_SENSOR_CHAMBER 3
opt_add CHAMBER_HEATER_PIN 45
exec_test $1 $2 "RAMPS with 2 extruders, RRDFGSC, Linear ABL, LEDs, and many options" exec_test $1 $2 "RAMPS with 2 extruders, RRDFGSC, Linear ABL, LEDs, and many options"
# #

2
config/default/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/default/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/3DFabXYZ/Migbot/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -550,6 +551,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/3DFabXYZ/Migbot/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/AlephObjects/TAZ4/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 7 #define TEMP_SENSOR_BED 7
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -565,6 +566,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/AlephObjects/TAZ4/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/AliExpress/CL-260/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

2
config/examples/AliExpress/UM2pExt/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 20 #define TEMP_SENSOR_BED 20
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -556,6 +557,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/AliExpress/UM2pExt/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Anet/A2/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Anet/A2/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Anet/A2plus/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Anet/A2plus/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Anet/A6/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 11 #define TEMP_SENSOR_BED 11
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -565,6 +566,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Anet/A6/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Anet/A8/Configuration.h
Unescape Escape View File

@ -378,6 +378,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -558,6 +559,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Anet/A8/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/AnyCubic/i3/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -555,6 +556,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/AnyCubic/i3/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/ArmEd/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 13 #define TEMP_SENSOR_BED 13
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -546,6 +547,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/ArmEd/Configuration_adv.h
Unescape Escape View File

@ -116,6 +116,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Azteeg/X5GT/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

2
config/examples/BIBO/TouchX/cyclops/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 1 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 1 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/BIBO/TouchX/default/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 60 #define TEMP_SENSOR_BED 60
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/BIBO/TouchX/default/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/BQ/Hephestos/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -533,6 +534,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/BQ/Hephestos/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/BQ/Hephestos_2/Configuration.h
Unescape Escape View File

@ -385,6 +385,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -546,6 +547,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/BQ/Hephestos_2/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/BQ/WITBOX/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -533,6 +534,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/BQ/WITBOX/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Cartesio/Configuration.h
Unescape Escape View File

@ -378,6 +378,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -544,6 +545,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Cartesio/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/CR-10/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -555,6 +556,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/CR-10/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/CR-10S/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/CR-10S/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/CR-10_5S/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/CR-10_5S/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/CR-10mini/Configuration.h
Unescape Escape View File

@ -386,6 +386,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 5 #define TEMP_SENSOR_BED 5
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -564,6 +565,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/CR-10mini/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/CR-8/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -555,6 +556,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/CR-8/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/Ender-2/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -549,6 +550,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/Ender-2/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/Ender-3/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -549,6 +550,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/Ender-3/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Creality/Ender-4/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -555,6 +556,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Creality/Ender-4/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Einstart-S/Configuration.h
Unescape Escape View File

@ -379,6 +379,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 0 #define TEMP_SENSOR_BED 0
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -553,6 +554,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Einstart-S/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Felix/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -526,6 +527,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Felix/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Felix/DUAL/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -526,6 +527,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

2
config/examples/FlashForge/CreatorPro/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -535,6 +536,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/FlashForge/CreatorPro/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/FolgerTech/i3-2020/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -550,6 +551,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/FolgerTech/i3-2020/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Formbot/Raptor/Configuration.h
Unescape Escape View File

@ -422,6 +422,7 @@
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#endif #endif
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -597,6 +598,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Formbot/Raptor/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Formbot/T_Rex_2+/Configuration.h
Unescape Escape View File

@ -392,6 +392,7 @@
#endif #endif
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -574,6 +575,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Formbot/T_Rex_2+/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Formbot/T_Rex_3/Configuration.h
Unescape Escape View File

@ -386,6 +386,7 @@
#endif #endif
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -554,6 +555,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Formbot/T_Rex_3/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Geeetech/A10M/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -528,6 +529,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Geeetech/A10M/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Geeetech/A20M/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -528,6 +529,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

14
config/examples/Geeetech/A20M/Configuration_adv.h
Unescape Escape View File

@ -112,6 +112,20 @@
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
#endif #endif
/**
* Thermal Protection parameters for the heated chamber.
*/
#if ENABLED(THERMAL_PROTECTION_CHAMBER)
#define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds
#define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
/**
* Heated chamber watch settings (M141/M191).
*/
#define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds
#define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius
#endif
#if ENABLED(PIDTEMP) #if ENABLED(PIDTEMP)
// this adds an experimental additional term to the heating power, proportional to the extrusion speed. // this adds an experimental additional term to the heating power, proportional to the extrusion speed.
// if Kc is chosen well, the additional required power due to increased melting should be compensated. // if Kc is chosen well, the additional required power due to increased melting should be compensated.

2
config/examples/Geeetech/GT2560/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -560,6 +561,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

2
config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h
Unescape Escape View File

@ -377,6 +377,7 @@
#define TEMP_SENSOR_5 0 #define TEMP_SENSOR_5 0
#define TEMP_SENSOR_BED 1 #define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_CHAMBER 0 #define TEMP_SENSOR_CHAMBER 0
#define CHAMBER_HEATER_PIN -1 // On/off pin for enclosure heating system
// Dummy thermistor constant temperature readings, for use with 998 and 999 // Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25 #define DUMMY_THERMISTOR_998_VALUE 25
@ -545,6 +546,7 @@
#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed #define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed
#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
//=========================================================================== //===========================================================================
//============================= Mechanical Settings ========================= //============================= Mechanical Settings =========================

Some files were not shown because too many files have changed in this diff Show More

Write Preview
Loading…
Cancel
Save