|
|
|
|
@ -758,14 +758,15 @@
|
|
|
|
|
// even if it takes longer than DEFAULT_STEPPER_DEACTIVE_TIME.
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
/******************************************************************************\
|
|
|
|
|
* enable this section if you have TMC26X motor drivers.
|
|
|
|
|
* you need to import the TMC26XStepper library into the Arduino IDE for this
|
|
|
|
|
******************************************************************************/
|
|
|
|
|
|
|
|
|
|
// @section tmc
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
* Enable this section if you have TMC26X motor drivers.
|
|
|
|
|
* You will need to import the TMC26XStepper library into the Arduino IDE for this
|
|
|
|
|
* (https://github.com/trinamic/TMC26XStepper.git)
|
|
|
|
|
*/
|
|
|
|
|
//#define HAVE_TMCDRIVER
|
|
|
|
|
|
|
|
|
|
#if ENABLED(HAVE_TMCDRIVER)
|
|
|
|
|
|
|
|
|
|
//#define X_IS_TMC
|
|
|
|
|
@ -823,23 +824,31 @@
|
|
|
|
|
|
|
|
|
|
// @section TMC2130
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
* Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
|
|
|
|
|
*
|
|
|
|
|
* To use TMC2130 drivers in SPI mode, you'll also need the TMC2130 Arduino library
|
|
|
|
|
* (https://github.com/makertum/Trinamic_TMC2130).
|
|
|
|
|
* You'll also need the TMC2130Stepper Arduino library
|
|
|
|
|
* (https://github.com/teemuatlut/TMC2130Stepper).
|
|
|
|
|
*
|
|
|
|
|
* To use TMC2130 stepper drivers in SPI mode connect your SPI2130 pins to
|
|
|
|
|
* the hardware SPI interface on your board and define the required CS pins
|
|
|
|
|
* in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
|
|
|
|
|
*/
|
|
|
|
|
//#define HAVE_TMC2130
|
|
|
|
|
|
|
|
|
|
//#define HAVE_TMC2130DRIVER
|
|
|
|
|
|
|
|
|
|
#if ENABLED(HAVE_TMC2130DRIVER)
|
|
|
|
|
#if ENABLED(HAVE_TMC2130)
|
|
|
|
|
#define STEALTHCHOP
|
|
|
|
|
|
|
|
|
|
//#define TMC2130_ADVANCED_CONFIGURATION
|
|
|
|
|
/**
|
|
|
|
|
* Let Marlin automatically control stepper current.
|
|
|
|
|
* This is still an experimental feature.
|
|
|
|
|
* Increase current every 5s by CURRENT_STEP until stepper temperature prewarn gets triggered,
|
|
|
|
|
* then decrease current by CURRENT_STEP until temperature prewarn is cleared.
|
|
|
|
|
* Adjusting starts from X/Y/Z/E_MAX_CURRENT but will not increase over AUTO_ADJUST_MAX
|
|
|
|
|
*/
|
|
|
|
|
//#define AUTOMATIC_CURRENT_CONTROL
|
|
|
|
|
#define CURRENT_STEP 50 // [mA]
|
|
|
|
|
#define AUTO_ADJUST_MAX 1300 // [mA], 1300mA_rms = 1840mA_peak
|
|
|
|
|
|
|
|
|
|
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
|
|
|
|
|
//#define X_IS_TMC2130
|
|
|
|
|
@ -853,180 +862,68 @@
|
|
|
|
|
//#define E2_IS_TMC2130
|
|
|
|
|
//#define E3_IS_TMC2130
|
|
|
|
|
|
|
|
|
|
#if ENABLED(TMC2130_ADVANCED_CONFIGURATION)
|
|
|
|
|
|
|
|
|
|
// If you've enabled TMC2130_ADVANCED_CONFIGURATION, define global settings below.
|
|
|
|
|
// Enabled settings will be automatically applied to all axes specified above.
|
|
|
|
|
//
|
|
|
|
|
// Please read the TMC2130 datasheet:
|
|
|
|
|
// http://www.trinamic.com/_articles/products/integrated-circuits/tmc2130/_datasheet/TMC2130_datasheet.pdf
|
|
|
|
|
// All settings here have the same (sometimes cryptic) names as in the datasheet.
|
|
|
|
|
//
|
|
|
|
|
// The following, uncommented settings are only suggestion.
|
|
|
|
|
|
|
|
|
|
/* GENERAL CONFIGURATION */
|
|
|
|
|
|
|
|
|
|
//#define GLOBAL_EN_PWM_MODE 0
|
|
|
|
|
#define GLOBAL_I_SCALE_ANALOG 1 // [0,1] 0: Normal, 1: AIN
|
|
|
|
|
//#define GLOBAL_INTERNAL_RSENSE 0 // [0,1] 0: Normal, 1: Internal
|
|
|
|
|
#define GLOBAL_EN_PWM_MODE 0 // [0,1] 0: Normal, 1: stealthChop with velocity threshold
|
|
|
|
|
//#define GLOBAL_ENC_COMMUTATION 0 // [0,1]
|
|
|
|
|
#define GLOBAL_SHAFT 0 // [0,1] 0: normal, 1: invert
|
|
|
|
|
//#define GLOBAL_DIAG0_ERROR 0 // [0,1]
|
|
|
|
|
//#define GLOBAL_DIAG0_OTPW 0 // [0,1]
|
|
|
|
|
//#define GLOBAL_DIAG0_STALL 0 // [0,1]
|
|
|
|
|
//#define GLOBAL_DIAG1_STALL 0 // [0,1]
|
|
|
|
|
//#define GLOBAL_DIAG1_INDEX 0 // [0,1]
|
|
|
|
|
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
|
|
|
|
|
//#define GLOBAL_DIAG1_ONSTATE 0 // [0,1]
|
|
|
|
|
//#define GLOBAL_DIAG0_INT_PUSHPULL 0 // [0,1]
|
|
|
|
|
//#define GLOBAL_DIAG1_INT_PUSHPULL 0 // [0,1]
|
|
|
|
|
//#define GLOBAL_SMALL_HYSTERESIS 0 // [0,1]
|
|
|
|
|
//#define GLOBAL_STOP_ENABLE 0 // [0,1]
|
|
|
|
|
//#define GLOBAL_DIRECT_MODE 0 // [0,1]
|
|
|
|
|
|
|
|
|
|
/* VELOCITY-DEPENDENT DRIVE FEATURES */
|
|
|
|
|
|
|
|
|
|
#define GLOBAL_IHOLD 22 // [0-31] 0: min, 31: max
|
|
|
|
|
#define GLOBAL_IRUN 31 // [0-31] 0: min, 31: max
|
|
|
|
|
#define GLOBAL_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
|
|
|
|
|
//#define GLOBAL_TPOWERDOWN 0 // [0-255] 0: min, 255: about 4 seconds
|
|
|
|
|
//#define GLOBAL_TPWMTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
|
|
|
|
|
//#define GLOBAL_TCOOLTHRS 0 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
|
|
|
|
|
#define GLOBAL_THIGH 10 // [0-1048576] e.g. 20 corresponds with 2000 steps/s
|
|
|
|
|
|
|
|
|
|
/* SPI MODE CONFIGURATION */
|
|
|
|
|
|
|
|
|
|
//#define GLOBAL_XDIRECT 0
|
|
|
|
|
|
|
|
|
|
/* DCSTEP MINIMUM VELOCITY */
|
|
|
|
|
|
|
|
|
|
//#define GLOBAL_VDCMIN 0
|
|
|
|
|
|
|
|
|
|
/* MOTOR DRIVER CONFIGURATION*/
|
|
|
|
|
|
|
|
|
|
//#define GLOBAL_DEDGE 0
|
|
|
|
|
//#define GLOBAL_DISS2G 0
|
|
|
|
|
#define GLOBAL_INTPOL 1 // 0: off 1: 256 microstep interpolation
|
|
|
|
|
#define GLOBAL_MRES 16 // number of microsteps
|
|
|
|
|
#define GLOBAL_SYNC 1 // [0-15]
|
|
|
|
|
#define GLOBAL_VHIGHCHM 1 // [0,1] 0: normal, 1: high velocity stepper mode
|
|
|
|
|
#define GLOBAL_VHIGHFS 0 // [0,1] 0: normal, 1: switch to full steps for high velocities
|
|
|
|
|
// #define GLOBAL_VSENSE 0 // [0,1] 0: normal, 1: high sensitivity (not recommended)
|
|
|
|
|
#define GLOBAL_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
|
|
|
|
|
#define GLOBAL_CHM 0 // [0,1] 0: spreadCycle, 1: Constant off time with fast decay time.
|
|
|
|
|
//#define GLOBAL_RNDTF 0
|
|
|
|
|
//#define GLOBAL_DISFDCC 0
|
|
|
|
|
//#define GLOBAL_FD 0
|
|
|
|
|
//#define GLOBAL_HEND 0
|
|
|
|
|
//#define GLOBAL_HSTRT 0
|
|
|
|
|
#define GLOBAL_TOFF 10 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
|
|
|
|
|
|
|
|
|
|
//#define GLOBAL_SFILT 0
|
|
|
|
|
//#define GLOBAL_SGT 0
|
|
|
|
|
//#define GLOBAL_SEIMIN 0
|
|
|
|
|
//#define GLOBAL_SEDN 0
|
|
|
|
|
//#define GLOBAL_SEMAX 0
|
|
|
|
|
//#define GLOBAL_SEUP 0
|
|
|
|
|
//#define GLOBAL_SEMIN 0
|
|
|
|
|
|
|
|
|
|
//#define GLOBAL_DC_TIME 0
|
|
|
|
|
//#define GLOBAL_DC_SG 0
|
|
|
|
|
|
|
|
|
|
//#define GLOBAL_FREEWHEEL 0
|
|
|
|
|
//#define GLOBAL_PWM_SYMMETRIC 0
|
|
|
|
|
//#define GLOBAL_PWM_AUTOSCALE 0
|
|
|
|
|
//#define GLOBAL_PWM_FREQ 0
|
|
|
|
|
//#define GLOBAL_PWM_GRAD 0
|
|
|
|
|
//#define GLOBAL_PWM_AMPL 0
|
|
|
|
|
|
|
|
|
|
//#define GLOBAL_ENCM_CTRL 0
|
|
|
|
|
|
|
|
|
|
#else
|
|
|
|
|
|
|
|
|
|
#define X_IHOLD 31 // [0-31] 0: min, 31: max
|
|
|
|
|
#define X_IRUN 31 // [0-31] 0: min, 31: max
|
|
|
|
|
#define X_IHOLDDELAY 15 // [0-15] 0: min, 15: about 4 seconds
|
|
|
|
|
#define X_I_SCALE_ANALOG 1 // 0: Normal, 1: AIN
|
|
|
|
|
#define X_MRES 16 // number of microsteps
|
|
|
|
|
#define X_TBL 1 // 0-3: set comparator blank time to 16, 24, 36 or 54 clocks, 1 or 2 is recommended
|
|
|
|
|
#define X_TOFF 8 // 0: driver disable, 1: use only with TBL>2, 2-15: off time setting during slow decay phase
|
|
|
|
|
|
|
|
|
|
#define X2_IHOLD 31
|
|
|
|
|
#define X2_IRUN 31
|
|
|
|
|
#define X2_IHOLDDELAY 15
|
|
|
|
|
#define X2_I_SCALE_ANALOG 1
|
|
|
|
|
#define X2_MRES 16
|
|
|
|
|
#define X2_TBL 1
|
|
|
|
|
#define X2_TOFF 8
|
|
|
|
|
|
|
|
|
|
#define Y_IHOLD 31
|
|
|
|
|
#define Y_IRUN 31
|
|
|
|
|
#define Y_IHOLDDELAY 15
|
|
|
|
|
#define Y_I_SCALE_ANALOG 1
|
|
|
|
|
#define Y_MRES 16
|
|
|
|
|
#define Y_TBL 1
|
|
|
|
|
#define Y_TOFF 8
|
|
|
|
|
|
|
|
|
|
#define Y2_IHOLD 31
|
|
|
|
|
#define Y2_IRUN 31
|
|
|
|
|
#define Y2_IHOLDDELAY 15
|
|
|
|
|
#define Y2_I_SCALE_ANALOG 1
|
|
|
|
|
#define Y2_MRES 16
|
|
|
|
|
#define Y2_TBL 1
|
|
|
|
|
#define Y2_TOFF 8
|
|
|
|
|
|
|
|
|
|
#define Z_IHOLD 31
|
|
|
|
|
#define Z_IRUN 31
|
|
|
|
|
#define Z_IHOLDDELAY 15
|
|
|
|
|
#define Z_I_SCALE_ANALOG 1
|
|
|
|
|
#define Z_MRES 16
|
|
|
|
|
#define Z_TBL 1
|
|
|
|
|
#define Z_TOFF 8
|
|
|
|
|
|
|
|
|
|
#define Z2_IHOLD 31
|
|
|
|
|
#define Z2_IRUN 31
|
|
|
|
|
#define Z2_IHOLDDELAY 15
|
|
|
|
|
#define Z2_I_SCALE_ANALOG 1
|
|
|
|
|
#define Z2_MRES 16
|
|
|
|
|
#define Z2_TBL 1
|
|
|
|
|
#define Z2_TOFF 8
|
|
|
|
|
|
|
|
|
|
#define E0_IHOLD 31
|
|
|
|
|
#define E0_IRUN 31
|
|
|
|
|
#define E0_IHOLDDELAY 15
|
|
|
|
|
#define E0_I_SCALE_ANALOG 1
|
|
|
|
|
#define E0_MRES 16
|
|
|
|
|
#define E0_TBL 1
|
|
|
|
|
#define E0_TOFF 8
|
|
|
|
|
|
|
|
|
|
#define E1_IHOLD 31
|
|
|
|
|
#define E1_IRUN 31
|
|
|
|
|
#define E1_IHOLDDELAY 15
|
|
|
|
|
#define E1_I_SCALE_ANALOG 1
|
|
|
|
|
#define E1_MRES 16
|
|
|
|
|
#define E1_TBL 1
|
|
|
|
|
#define E1_TOFF 8
|
|
|
|
|
|
|
|
|
|
#define E2_IHOLD 31
|
|
|
|
|
#define E2_IRUN 31
|
|
|
|
|
#define E2_IHOLDDELAY 15
|
|
|
|
|
#define E2_I_SCALE_ANALOG 1
|
|
|
|
|
#define E2_MRES 16
|
|
|
|
|
#define E2_TBL 1
|
|
|
|
|
#define E2_TOFF 8
|
|
|
|
|
|
|
|
|
|
#define E3_IHOLD 31
|
|
|
|
|
#define E3_IRUN 31
|
|
|
|
|
#define E3_IHOLDDELAY 15
|
|
|
|
|
#define E3_I_SCALE_ANALOG 1
|
|
|
|
|
#define E3_MRES 16
|
|
|
|
|
#define E3_TBL 1
|
|
|
|
|
#define E3_TOFF 8
|
|
|
|
|
|
|
|
|
|
#endif // TMC2130_ADVANCED_CONFIGURATION
|
|
|
|
|
|
|
|
|
|
#endif // HAVE_TMC2130DRIVER
|
|
|
|
|
/**
|
|
|
|
|
* Stepper driver settings
|
|
|
|
|
*/
|
|
|
|
|
|
|
|
|
|
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
|
|
|
|
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
|
|
|
|
#define INTERPOLATE 1 // Interpolate X/Y/Z_MICROSTEPS to 256
|
|
|
|
|
|
|
|
|
|
#define X_MAX_CURRENT 1000 // rms current in mA
|
|
|
|
|
#define X_MICROSTEPS 16 // FULLSTEP..256
|
|
|
|
|
#define X_CHIP_SELECT 40 // Pin
|
|
|
|
|
|
|
|
|
|
#define Y_MAX_CURRENT 1000
|
|
|
|
|
#define Y_MICROSTEPS 16
|
|
|
|
|
#define Y_CHIP_SELECT 42
|
|
|
|
|
|
|
|
|
|
#define Z_MAX_CURRENT 1000
|
|
|
|
|
#define Z_MICROSTEPS 16
|
|
|
|
|
#define Z_CHIP_SELECT 65
|
|
|
|
|
|
|
|
|
|
//#define X2_MAX_CURRENT 1000
|
|
|
|
|
//#define X2_MICROSTEPS 16
|
|
|
|
|
//#define X2_CHIP_SELECT -1
|
|
|
|
|
|
|
|
|
|
//#define Y2_MAX_CURRENT 1000
|
|
|
|
|
//#define Y2_MICROSTEPS 16
|
|
|
|
|
//#define Y2_CHIP_SELECT -1
|
|
|
|
|
|
|
|
|
|
//#define Z2_MAX_CURRENT 1000
|
|
|
|
|
//#define Z2_MICROSTEPS 16
|
|
|
|
|
//#define Z2_CHIP_SELECT -1
|
|
|
|
|
|
|
|
|
|
//#define E0_MAX_CURRENT 1000
|
|
|
|
|
//#define E0_MICROSTEPS 16
|
|
|
|
|
//#define E0_CHIP_SELECT -1
|
|
|
|
|
|
|
|
|
|
//#define E1_MAX_CURRENT 1000
|
|
|
|
|
//#define E1_MICROSTEPS 16
|
|
|
|
|
//#define E1_CHIP_SELECT -1
|
|
|
|
|
|
|
|
|
|
//#define E2_MAX_CURRENT 1000
|
|
|
|
|
//#define E2_MICROSTEPS 16
|
|
|
|
|
//#define E2_CHIP_SELECT -1
|
|
|
|
|
|
|
|
|
|
//#define E3_MAX_CURRENT 1000
|
|
|
|
|
//#define E3_MICROSTEPS 16
|
|
|
|
|
//#define E3_CHIP_SELECT -1
|
|
|
|
|
|
|
|
|
|
/**
|
|
|
|
|
* You can set your own advanced settings by filling in predefined functions.
|
|
|
|
|
* A list of available functions can be found on the library github page
|
|
|
|
|
* https://github.com/teemuatlut/TMC2130Stepper
|
|
|
|
|
*
|
|
|
|
|
* Example:
|
|
|
|
|
* #define TMC2130_ADV() { \
|
|
|
|
|
* stepperX.diag0_temp_prewarn(1); \
|
|
|
|
|
* stepperX.interpolate(0); \
|
|
|
|
|
* }
|
|
|
|
|
*/
|
|
|
|
|
#define TMC2130_ADV() { }
|
|
|
|
|
|
|
|
|
|
#endif // ENABLED(HAVE_TMC2130)
|
|
|
|
|
|
|
|
|
|
// @section L6470
|
|
|
|
|
|
|
|
|
|
|
Scott Lahteine
8 years ago