|
|
@ -94,6 +94,11 @@
|
|
|
|
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
|
|
|
|
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
|
|
|
|
//#define FAN_KICKSTART_TIME 100
|
|
|
|
//#define FAN_KICKSTART_TIME 100
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
// This defines the minimal speed for the main fan, run in PWM mode
|
|
|
|
|
|
|
|
// to enable uncomment and set minimal PWM speed for reliable running (1-255)
|
|
|
|
|
|
|
|
// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
|
|
|
|
|
|
|
|
//#define FAN_MIN_PWM 50
|
|
|
|
|
|
|
|
|
|
|
|
// @section extruder
|
|
|
|
// @section extruder
|
|
|
|
|
|
|
|
|
|
|
|
// Extruder cooling fans
|
|
|
|
// Extruder cooling fans
|
|
|
@ -290,7 +295,9 @@
|
|
|
|
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
|
|
|
|
// You can get round this by connecting a push button or single throw switch to the pin defined as SDCARDCARDDETECT
|
|
|
|
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
|
|
|
|
// in the pins.h file. When using a push button pulling the pin to ground this will need inverted. This setting should
|
|
|
|
// be commented out otherwise
|
|
|
|
// be commented out otherwise
|
|
|
|
|
|
|
|
#ifndef ELB_FULL_GRAPHIC_CONTROLLER
|
|
|
|
#define SDCARDDETECTINVERTED
|
|
|
|
#define SDCARDDETECTINVERTED
|
|
|
|
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
|
|
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
|
|
|
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
|
|
|
|
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
|
|
|
#define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the z enabled so your bed stays in place.
|
|
|
@ -448,6 +455,9 @@ const unsigned int dropsegments=5; //everything with less than this number of st
|
|
|
|
#define FILAMENTCHANGE_ZADD 10
|
|
|
|
#define FILAMENTCHANGE_ZADD 10
|
|
|
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
|
|
|
#define FILAMENTCHANGE_FIRSTRETRACT -2
|
|
|
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
|
|
|
#define FILAMENTCHANGE_FINALRETRACT -100
|
|
|
|
|
|
|
|
#define AUTO_FILAMENT_CHANGE //This extrude filament until you press the button on LCD
|
|
|
|
|
|
|
|
#define AUTO_FILAMENT_CHANGE_LENGTH 0.04 //Extrusion length on automatic extrusion loop
|
|
|
|
|
|
|
|
#define AUTO_FILAMENT_CHANGE_FEEDRATE 300 //Extrusion feedrate (mm/min) on automatic extrusion loop
|
|
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#endif
|
|
|
|
#endif
|
|
|
|
|
|
|
|
|
|
|
|