microlab
/
scube
1
1
Fork 0
Code Issues Pull Requests Releases Activity

Merge branch 'Marlin_v1' of https://github.com/ErikZalm/Marlin into Marlin_v1

Browse Source
2.0.x
Bernhard 13 years ago
parent f312216e97 554cc1718d
commit 4bababf5b0
14 changed files with 5869 additions and 5595 deletions
Show Stats Download Patch File Download Diff File

65
Marlin/Configuration.h
Unescape Escape View File

@ -43,16 +43,20 @@
// 5 is ParCan supplied 104GT-2 100K // 5 is ParCan supplied 104GT-2 100K
// 6 is EPCOS 100k // 6 is EPCOS 100k
// 7 is 100k Honeywell thermistor 135-104LAG-J01 // 7 is 100k Honeywell thermistor 135-104LAG-J01
//#define THERMISTORHEATER_0 3 //#define THERMISTORHEATER_0 3
//#define THERMISTORHEATER_1 3 //#define THERMISTORHEATER_1 1
//#define THERMISTORBED 3 //#define THERMISTORHEATER_2 1
//#define HEATER_0_USES_THERMISTOR //#define HEATER_0_USES_THERMISTOR
//#define HEATER_1_USES_THERMISTOR //#define HEATER_1_USES_THERMISTOR
//#define HEATER_2_USES_THERMISTOR
#define HEATER_0_USES_AD595 #define HEATER_0_USES_AD595
//#define HEATER_1_USES_AD595 //#define HEATER_1_USES_AD595
//#define HEATER_2_USES_AD595
// Select one of these only to define how the bed temp is read. // Select one of these only to define how the bed temp is read.
//#define THERMISTORBED 1
//#define BED_USES_THERMISTOR //#define BED_USES_THERMISTOR
//#define BED_USES_AD595 //#define BED_USES_AD595
@ -65,12 +69,13 @@
//#define WATCHPERIOD 20000 //20 seconds //#define WATCHPERIOD 20000 //20 seconds
// Actual temperature must be close to target for this long before M109 returns success // Actual temperature must be close to target for this long before M109 returns success
//#define TEMP_RESIDENCY_TIME 20 // (seconds) #define TEMP_RESIDENCY_TIME 30 // (seconds)
//#define TEMP_HYSTERESIS 5 // (C°) range of +/- temperatures considered "close" to the target one #define TEMP_HYSTERESIS 3 // (C°) range of +/- temperatures considered "close" to the target one
//// The minimal temperature defines the temperature below which the heater will not be enabled //// The minimal temperature defines the temperature below which the heater will not be enabled
#define HEATER_0_MINTEMP 5 #define HEATER_0_MINTEMP 5
//#define HEATER_1_MINTEMP 5 //#define HEATER_1_MINTEMP 5
//#define HEATER_2_MINTEMP 5
//#define BED_MINTEMP 5 //#define BED_MINTEMP 5
@ -79,6 +84,7 @@
// You should use MINTEMP for thermistor short/failure protection. // You should use MINTEMP for thermistor short/failure protection.
#define HEATER_0_MAXTEMP 275 #define HEATER_0_MAXTEMP 275
//#define HEATER_1_MAXTEMP 275 //#define HEATER_1_MAXTEMP 275
//#define HEATER_2_MAXTEMP 275
//#define BED_MAXTEMP 150 //#define BED_MAXTEMP 150
@ -90,21 +96,17 @@
// Heating is finished if a temperature close to this degree shift is reached // Heating is finished if a temperature close to this degree shift is reached
#define HEATING_EARLY_FINISH_DEG_OFFSET 1 //Degree #define HEATING_EARLY_FINISH_DEG_OFFSET 1 //Degree
// PID settings: // PID settings:
// Uncomment the following line to enable PID support. // Uncomment the following line to enable PID support.
#define PIDTEMP #define PIDTEMP
#define PID_MAX 255 // limits current to nozzle; 255=full current
#ifdef PIDTEMP #ifdef PIDTEMP
#if MOTHERBOARD == 62
#error Sanguinololu does not support PID, sorry. Please disable it.
#endif
//#define PID_DEBUG // Sends debug data to the serial port. //#define PID_DEBUG // Sends debug data to the serial port.
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104 sets the output power in % //#define PID_OPENLOOP 1 // Puts PID in open loop. M104 sets the output power in %
#define PID_MAX 255 // limits current to nozzle; 255=full current
#define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term #define PID_INTEGRAL_DRIVE_MAX 255 //limit for the integral term
#define K1 0.95 //smoothing factor withing the PID #define K1 0.95 //smoothing factor withing the PID
#define PID_dT 0.1 //sampling period of the PID #define PID_dT 0.128 //sampling period of the PID
//To develop some PID settings for your machine, you can initiall follow //To develop some PID settings for your machine, you can initiall follow
// the Ziegler-Nichols method. // the Ziegler-Nichols method.
@ -132,6 +134,11 @@
#define DEFAULT_Ki (1.25*PID_dT) #define DEFAULT_Ki (1.25*PID_dT)
#define DEFAULT_Kd (99/PID_dT) #define DEFAULT_Kd (99/PID_dT)
// Makergear
// #define DEFAULT_Kp 7.0
// #define DEFAULT_Ki 0.1
// #define DEFAULT_Kd 12
// Mendel Parts V9 on 12V // Mendel Parts V9 on 12V
// #define DEFAULT_Kp 63.0 // #define DEFAULT_Kp 63.0
// #define DEFAULT_Ki (2.25*PID_dT) // #define DEFAULT_Ki (2.25*PID_dT)
@ -149,7 +156,7 @@
// if Kc is choosen well, the additional required power due to increased melting should be compensated. // if Kc is choosen well, the additional required power due to increased melting should be compensated.
#define PID_ADD_EXTRUSION_RATE #define PID_ADD_EXTRUSION_RATE
#ifdef PID_ADD_EXTRUSION_RATE #ifdef PID_ADD_EXTRUSION_RATE
#define DEFAULT_Kc (3) //heatingpower=Kc*(e_speed) #define DEFAULT_Kc (1) //heatingpower=Kc*(e_speed)
#endif #endif
#endif // PIDTEMP #endif // PIDTEMP
@ -169,36 +176,39 @@
// Endstop Settings // Endstop Settings
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors #define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins. // The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops.
// For optos H21LOB set to true, for Mendel-Parts newer optos TCST2103 set to false // For optos H21LOB set to true, for Mendel-Parts newer optos TCST2103 set to false
//#define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing #define ENDSTOPS_ONLY_FOR_HOMING // If defined the endstops will only be used for homing
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
#define X_ENABLE_ON 0 #define X_ENABLE_ON 0
#define Y_ENABLE_ON 0 #define Y_ENABLE_ON 0
#define Z_ENABLE_ON 0 #define Z_ENABLE_ON 0
#define E_ENABLE_ON 0 #define E_ENABLE_ON 0 // For all extruders
// Disables axis when it's not being used. // Disables axis when it's not being used.
#define DISABLE_X false #define DISABLE_X false
#define DISABLE_Y false #define DISABLE_Y false
#define DISABLE_Z false #define DISABLE_Z false
#define DISABLE_E false #define DISABLE_E false // For all extruders
// Inverting axis direction // Inverting axis direction
//#define INVERT_X_DIR false // for Mendel set to false, for Orca set to true //#define INVERT_X_DIR false // for Mendel set to false, for Orca set to true
//#define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false //#define INVERT_Y_DIR true // for Mendel set to true, for Orca set to false
//#define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true //#define INVERT_Z_DIR false // for Mendel set to false, for Orca set to true
//#define INVERT_E_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false //#define INVERT_E*_DIR true // for direct drive extruder v9 set to true, for geared extruder set to false, used for all extruders
#define INVERT_X_DIR true // for Mendel set to false, for Orca set to true #define INVERT_X_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false #define INVERT_Y_DIR false // for Mendel set to true, for Orca set to false
#define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true #define INVERT_Z_DIR true // for Mendel set to false, for Orca set to true
#define INVERT_E_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false #define INVERT_E0_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E1_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
#define INVERT_E2_DIR false // for direct drive extruder v9 set to true, for geared extruder set to false
//// ENDSTOP SETTINGS: //// ENDSTOP SETTINGS:
// Sets direction of endstops when homing; 1=MAX, -1=MIN // Sets direction of endstops when homing; 1=MAX, -1=MIN
@ -206,11 +216,11 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#define Y_HOME_DIR -1 #define Y_HOME_DIR -1
#define Z_HOME_DIR -1 #define Z_HOME_DIR -1
#define min_software_endstops false //If true, axis won't move to coordinates less than zero. #define min_software_endstops true //If true, axis won't move to coordinates less than zero.
#define max_software_endstops false //If true, axis won't move to coordinates greater than the defined lengths below. #define max_software_endstops true //If true, axis won't move to coordinates greater than the defined lengths below.
#define X_MAX_LENGTH 210 #define X_MAX_LENGTH 205
#define Y_MAX_LENGTH 210 #define Y_MAX_LENGTH 205
#define Z_MAX_LENGTH 210 #define Z_MAX_LENGTH 200
//// MOVEMENT SETTINGS //// MOVEMENT SETTINGS
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
@ -229,7 +239,8 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
// default settings // default settings
#define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for ultimaker #define DEFAULT_AXIS_STEPS_PER_UNIT {78.7402,78.7402,200*8/3,760*1.1} // default steps per unit for ultimaker
//#define DEFAULT_AXIS_STEPS_PER_UNIT {40, 40, 3333.92, 67} //sells mendel with v9 extruder //#define DEFAULT_AXIS_STEPS_PER_UNIT {40, 40, 3333.92, 360} //sells mendel with v9 extruder
//#define DEFAULT_AXIS_STEPS_PER_UNIT {80.3232, 80.8900, 2284.7651, 757.2218} // SAE Prusa w/ Wade extruder
#define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec) #define DEFAULT_MAX_FEEDRATE {500, 500, 5, 45} // (mm/sec)
#define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot. #define DEFAULT_MAX_ACCELERATION {9000,9000,100,10000} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for skeinforge 40+, for older versions raise them a lot.
@ -285,10 +296,10 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
// hooke's law says: force = k * distance // hooke's law says: force = k * distance
// bernoulli's priniciple says: v ^ 2 / 2 + g . h + pressure / density = constant // bernoulli's priniciple says: v ^ 2 / 2 + g . h + pressure / density = constant
// so: v ^ 2 is proportional to number of steps we advance the extruder // so: v ^ 2 is proportional to number of steps we advance the extruder
//#define ADVANCE #define ADVANCE
#ifdef ADVANCE #ifdef ADVANCE
#define EXTRUDER_ADVANCE_K .3 #define EXTRUDER_ADVANCE_K .0
#define D_FILAMENT 2.85 #define D_FILAMENT 2.85
#define STEPS_MM_E 836 #define STEPS_MM_E 836
@ -304,7 +315,7 @@ const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of th
#define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers? #define SD_FINISHED_STEPPERRELEASE true //if sd support and the file is finished: disable steppers?
#define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift. #define SD_FINISHED_RELEASECOMMAND "M84 X Y E" // no z because of layer shift.
//#define ULTIPANEL #define ULTIPANEL
#ifdef ULTIPANEL #ifdef ULTIPANEL
//#define NEWPANEL //enable this if you have a click-encoder panel //#define NEWPANEL //enable this if you have a click-encoder panel
#define SDSUPPORT #define SDSUPPORT

30
Marlin/Marlin.h
Unescape Escape View File

@ -101,14 +101,31 @@ void manage_inactivity(byte debug);
#define disable_z() ; #define disable_z() ;
#endif #endif
#if E_ENABLE_PIN > -1 #if defined(E0_ENABLE_PIN) && (E0_ENABLE_PIN > -1)
#define enable_e() WRITE(E_ENABLE_PIN, E_ENABLE_ON) #define enable_e0() WRITE(E0_ENABLE_PIN, E_ENABLE_ON)
#define disable_e() WRITE(E_ENABLE_PIN,!E_ENABLE_ON) #define disable_e0() WRITE(E0_ENABLE_PIN,!E_ENABLE_ON)
#else #else
#define enable_e() ; #define enable_e0() /* nothing */
#define disable_e() ; #define disable_e0() /* nothing */
#endif #endif
#if (EXTRUDERS > 1) && defined(E1_ENABLE_PIN) && (E1_ENABLE_PIN > -1)
#define enable_e1() WRITE(E1_ENABLE_PIN, E_ENABLE_ON)
#define disable_e1() WRITE(E1_ENABLE_PIN,!E_ENABLE_ON)
#else
#define enable_e1() /* nothing */
#define disable_e1() /* nothing */
#endif
#if (EXTRUDERS > 2) && defined(E2_ENABLE_PIN) && (E2_ENABLE_PIN > -1)
#define enable_e2() WRITE(E2_ENABLE_PIN, E_ENABLE_ON)
#define disable_e2() WRITE(E2_ENABLE_PIN,!E_ENABLE_ON)
#else
#define enable_e2() /* nothing */
#define disable_e2() /* nothing */
#endif
enum AxisEnum {X_AXIS=0, Y_AXIS=1, Z_AXIS=2, E_AXIS=3}; enum AxisEnum {X_AXIS=0, Y_AXIS=1, Z_AXIS=2, E_AXIS=3};
@ -133,4 +150,7 @@ extern float current_position[NUM_AXIS] ;
extern float add_homeing[3]; extern float add_homeing[3];
extern bool stop_heating_wait; extern bool stop_heating_wait;
// Handling multiple extruders pins
extern uint8_t active_extruder;
#endif #endif

124
Marlin/Marlin.pde
Unescape Escape View File

@ -122,7 +122,6 @@
//=========================================================================== //===========================================================================
//=============================imported variables============================ //=============================imported variables============================
//=========================================================================== //===========================================================================
extern float HeaterPower;
//=========================================================================== //===========================================================================
@ -136,9 +135,11 @@ bool axis_relative_modes[] = AXIS_RELATIVE_MODES;
volatile int feedmultiply=100; //100->1 200->2 volatile int feedmultiply=100; //100->1 200->2
int saved_feedmultiply; int saved_feedmultiply;
volatile bool feedmultiplychanged=false; volatile bool feedmultiplychanged=false;
float current_position[NUM_AXIS] = { 0.0, 0.0, 0.0, 0.0}; float current_position[NUM_AXIS] = { 0.0, 0.0, 0.0, 0.0 };
float add_homeing[3]={0,0,0}; float add_homeing[3]={0,0,0};
uint8_t active_extruder = 0;
bool stop_heating_wait=false; bool stop_heating_wait=false;
//=========================================================================== //===========================================================================
//=============================private variables============================= //=============================private variables=============================
//=========================================================================== //===========================================================================
@ -470,16 +471,16 @@ FORCE_INLINE bool code_seen(char code)
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); \ plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); \
destination[LETTER##_AXIS] = 1.5 * LETTER##_MAX_LENGTH * LETTER##_HOME_DIR; \ destination[LETTER##_AXIS] = 1.5 * LETTER##_MAX_LENGTH * LETTER##_HOME_DIR; \
feedrate = homing_feedrate[LETTER##_AXIS]; \ feedrate = homing_feedrate[LETTER##_AXIS]; \
prepare_move(); \ plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); \
\ \
current_position[LETTER##_AXIS] = 0;\ current_position[LETTER##_AXIS] = 0;\
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);\ plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);\
destination[LETTER##_AXIS] = -LETTER##_HOME_RETRACT_MM * LETTER##_HOME_DIR;\ destination[LETTER##_AXIS] = -LETTER##_HOME_RETRACT_MM * LETTER##_HOME_DIR;\
prepare_move(); \ plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); \
\ \
destination[LETTER##_AXIS] = 2*LETTER##_HOME_RETRACT_MM * LETTER##_HOME_DIR;\ destination[LETTER##_AXIS] = 2*LETTER##_HOME_RETRACT_MM * LETTER##_HOME_DIR;\
feedrate = homing_feedrate[LETTER##_AXIS]/2 ; \ feedrate = homing_feedrate[LETTER##_AXIS]/2 ; \
prepare_move(); \ plan_buffer_line(destination[X_AXIS], destination[Y_AXIS], destination[Z_AXIS], destination[E_AXIS], feedrate/60, active_extruder); \
\ \
current_position[LETTER##_AXIS] = (LETTER##_HOME_DIR == -1) ? 0 : LETTER##_MAX_LENGTH;\ current_position[LETTER##_AXIS] = (LETTER##_HOME_DIR == -1) ? 0 : LETTER##_MAX_LENGTH;\
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);\ plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);\
@ -543,6 +544,7 @@ FORCE_INLINE void process_commands()
if( code_seen(axis_codes[0]) && code_seen(axis_codes[1]) ) //first diagonal move if( code_seen(axis_codes[0]) && code_seen(axis_codes[1]) ) //first diagonal move
{ {
current_position[X_AXIS] = 0;current_position[Y_AXIS] = 0; current_position[X_AXIS] = 0;current_position[Y_AXIS] = 0;
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
destination[X_AXIS] = 1.5 * X_MAX_LENGTH * X_HOME_DIR;destination[Y_AXIS] = 1.5 * Y_MAX_LENGTH * Y_HOME_DIR; destination[X_AXIS] = 1.5 * X_MAX_LENGTH * X_HOME_DIR;destination[Y_AXIS] = 1.5 * Y_MAX_LENGTH * Y_HOME_DIR;
feedrate = homing_feedrate[X_AXIS]; feedrate = homing_feedrate[X_AXIS];
@ -582,7 +584,7 @@ FORCE_INLINE void process_commands()
} }
if(code_seen(axis_codes[Y_AXIS])) { if(code_seen(axis_codes[Y_AXIS])) {
current_position[1]=code_value()+add_homeing[1]; current_position[1]=code_value()+add_homeing[1];
} }
if(code_seen(axis_codes[Z_AXIS])) { if(code_seen(axis_codes[Z_AXIS])) {
@ -610,9 +612,11 @@ FORCE_INLINE void process_commands()
if(code_seen(axis_codes[i])) { if(code_seen(axis_codes[i])) {
current_position[i] = code_value()+add_homeing[i]; current_position[i] = code_value()+add_homeing[i];
if(i == E_AXIS) { if(i == E_AXIS) {
current_position[i] = code_value();
plan_set_e_position(current_position[E_AXIS]); plan_set_e_position(current_position[E_AXIS]);
} }
else { else {
current_position[i] = code_value()+add_homeing[i];
plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]); plan_set_position(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS]);
} }
} }
@ -623,7 +627,6 @@ FORCE_INLINE void process_commands()
else if(code_seen('M')) else if(code_seen('M'))
{ {
switch( (int)code_value() ) switch( (int)code_value() )
{ {
case 17: case 17:
@ -631,10 +634,12 @@ FORCE_INLINE void process_commands()
enable_x(); enable_x();
enable_y(); enable_y();
enable_z(); enable_z();
enable_e(); enable_e0();
enable_e1();
enable_e2();
break; break;
#ifdef SDSUPPORT
#ifdef SDSUPPORT
case 20: // M20 - list SD card case 20: // M20 - list SD card
SERIAL_PROTOCOLLNPGM("Begin file list"); SERIAL_PROTOCOLLNPGM("Begin file list");
card.ls(); card.ls();
@ -663,9 +668,8 @@ FORCE_INLINE void process_commands()
card.pauseSDPrint(); card.pauseSDPrint();
break; break;
case 26: //M26 - Set SD index case 26: //M26 - Set SD index
if(card.cardOK && code_seen('S')){ if(card.cardOK && code_seen('S')) {
card.setIndex(code_value_long()); card.setIndex(code_value_long());
} }
break; break;
case 27: //M27 - Get SD status case 27: //M27 - Get SD status
@ -679,16 +683,15 @@ FORCE_INLINE void process_commands()
*(starpos-1) = '\0'; *(starpos-1) = '\0';
} }
card.openFile(strchr_pointer+4,false); card.openFile(strchr_pointer+4,false);
break; break;
case 29: //M29 - Stop SD write case 29: //M29 - Stop SD write
//processed in write to file routine above //processed in write to file routine above
//card,saving = false; //card,saving = false;
break; break;
#endif //SDSUPPORT #endif //SDSUPPORT
case 30: //M30 take time since the start of the SD print or an M109 command case 30: //M30 take time since the start of the SD print or an M109 command
{ {
stoptime=millis(); stoptime=millis();
char time[30]; char time[30];
unsigned long t=(stoptime-starttime)/1000; unsigned long t=(stoptime-starttime)/1000;
@ -700,8 +703,8 @@ FORCE_INLINE void process_commands()
SERIAL_ECHOLN(time); SERIAL_ECHOLN(time);
LCD_MESSAGE(time); LCD_MESSAGE(time);
autotempShutdown(); autotempShutdown();
} }
break; break;
case 42: //M42 -Change pin status via gcode case 42: //M42 -Change pin status via gcode
if (code_seen('S')) if (code_seen('S'))
{ {
@ -755,21 +758,20 @@ FORCE_INLINE void process_commands()
break; break;
} }
} }
#if (TEMP_0_PIN > -1) || (TEMP_2_PIN > -1) #if (TEMP_0_PIN > -1)
SERIAL_PROTOCOLPGM("ok T:"); SERIAL_PROTOCOLPGM("ok T:");
SERIAL_PROTOCOL( degHotend(tmp_extruder)); SERIAL_PROTOCOL(degHotend(tmp_extruder));
#if TEMP_1_PIN > -1 #if TEMP_BED_PIN > -1
SERIAL_PROTOCOLPGM(" B:"); SERIAL_PROTOCOLPGM(" B:");
SERIAL_PROTOCOL(degBed()); SERIAL_PROTOCOL(degBed());
#endif //TEMP_1_PIN #endif //TEMP_BED_PIN
#else #else
SERIAL_ERROR_START; SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("No thermistors - no temp"); SERIAL_ERRORLNPGM("No thermistors - no temp");
#endif #endif
#ifdef PIDTEMP #ifdef PIDTEMP
SERIAL_PROTOCOLPGM(" @:"); SERIAL_PROTOCOLPGM(" @:");
SERIAL_PROTOCOL( HeaterPower); SERIAL_PROTOCOL(getHeaterPower(tmp_extruder));
#endif #endif
SERIAL_PROTOCOLLN(""); SERIAL_PROTOCOLLN("");
return; return;
@ -812,19 +814,33 @@ FORCE_INLINE void process_commands()
residencyStart = -1; residencyStart = -1;
/* continue to loop until we have reached the target temp /* continue to loop until we have reached the target temp
_and_ until TEMP_RESIDENCY_TIME hasn't passed since we reached it */ _and_ until TEMP_RESIDENCY_TIME hasn't passed since we reached it */
while((target_direction ? (isHeatingHotend(tmp_extruder)) : (isCoolingHotend(tmp_extruder))) || while((residencyStart == -1) ||
(residencyStart > -1 && (millis() - residencyStart) < TEMP_RESIDENCY_TIME*1000) ) { (residencyStart > -1 && (millis() - residencyStart) < TEMP_RESIDENCY_TIME*1000) ) {
#else #else
while ( target_direction ? (isHeatingHotend(tmp_extruder)) : (isCoolingHotend(tmp_extruder)&&(CooldownNoWait==false)) ) { while ( target_direction ? (isHeatingHotend(tmp_extruder)) : (isCoolingHotend(tmp_extruder)&&(CooldownNoWait==false)) ) {
#endif //TEMP_RESIDENCY_TIME #endif //TEMP_RESIDENCY_TIME
if( (millis() - codenum) > 1000 ) if( (millis() - codenum) > 1000 )
{ //Print Temp Reading every 1 second while heating up/cooling down { //Print Temp Reading and remaining time every 1 second while heating up/cooling down
SERIAL_PROTOCOLPGM("T:"); SERIAL_PROTOCOLPGM("T:");
SERIAL_PROTOCOLLN( degHotend(tmp_extruder) ); SERIAL_PROTOCOL( degHotend(tmp_extruder) );
codenum = millis(); SERIAL_PROTOCOLPGM(" E:");
} SERIAL_PROTOCOL( (int)tmp_extruder );
manage_heater(); #ifdef TEMP_RESIDENCY_TIME
LCD_STATUS; SERIAL_PROTOCOLPGM(" W:");
if(residencyStart > -1)
{
codenum = TEMP_RESIDENCY_TIME - ((millis() - residencyStart) / 1000);
SERIAL_PROTOCOLLN( codenum );
}
else
{
SERIAL_PROTOCOLLN( "?" );
}
#endif
codenum = millis();
}
manage_heater();
LCD_STATUS;
if(stop_heating_wait) break; if(stop_heating_wait) break;
#ifdef TEMP_RESIDENCY_TIME #ifdef TEMP_RESIDENCY_TIME
/* start/restart the TEMP_RESIDENCY_TIME timer whenever we reach target temp for the first time /* start/restart the TEMP_RESIDENCY_TIME timer whenever we reach target temp for the first time
@ -842,8 +858,8 @@ FORCE_INLINE void process_commands()
previous_millis_cmd = millis(); previous_millis_cmd = millis();
} }
break; break;
case 190: // M190 - Wait bed for heater to reach target. case 190: // M190 - Wait for bed heater to reach target.
#if TEMP_1_PIN > -1 #if TEMP_BED_PIN > -1
LCD_MESSAGEPGM("Bed Heating."); LCD_MESSAGEPGM("Bed Heating.");
if (code_seen('S')) setTargetBed(code_value()); if (code_seen('S')) setTargetBed(code_value());
codenum = millis(); codenum = millis();
@ -851,13 +867,13 @@ FORCE_INLINE void process_commands()
{ {
if( (millis()-codenum) > 1000 ) //Print Temp Reading every 1 second while heating up. if( (millis()-codenum) > 1000 ) //Print Temp Reading every 1 second while heating up.
{ {
float tt=degHotend0(); float tt=degHotend(active_extruder);
SERIAL_PROTOCOLPGM("T:"); SERIAL_PROTOCOLPGM("T:");
SERIAL_PROTOCOLLN(tt ); SERIAL_PROTOCOL(tt);
SERIAL_PROTOCOLPGM("ok T:"); SERIAL_PROTOCOLPGM(" E:");
SERIAL_PROTOCOL(tt ); SERIAL_PROTOCOL( (int)active_extruder );
SERIAL_PROTOCOLPGM(" B:"); SERIAL_PROTOCOLPGM(" B:");
SERIAL_PROTOCOLLN(degBed() ); SERIAL_PROTOCOLLN(degBed());
codenum = millis(); codenum = millis();
} }
manage_heater(); manage_heater();
@ -910,6 +926,9 @@ FORCE_INLINE void process_commands()
bool all_axis = !((code_seen(axis_codes[0])) || (code_seen(axis_codes[1])) || (code_seen(axis_codes[2]))|| (code_seen(axis_codes[3]))); bool all_axis = !((code_seen(axis_codes[0])) || (code_seen(axis_codes[1])) || (code_seen(axis_codes[2]))|| (code_seen(axis_codes[3])));
if(all_axis) if(all_axis)
{ {
disable_e0();
disable_e1();
disable_e2();
finishAndDisableSteppers(); finishAndDisableSteppers();
} }
else else
@ -918,8 +937,12 @@ FORCE_INLINE void process_commands()
if(code_seen('X')) disable_x(); if(code_seen('X')) disable_x();
if(code_seen('Y')) disable_y(); if(code_seen('Y')) disable_y();
if(code_seen('Z')) disable_z(); if(code_seen('Z')) disable_z();
#if ((E_ENABLE_PIN != X_ENABLE_PIN) && (E_ENABLE_PIN != Y_ENABLE_PIN)) // Only enable on boards that have seperate ENABLE_PINS #if ((E0_ENABLE_PIN != X_ENABLE_PIN) && (E1_ENABLE_PIN != Y_ENABLE_PIN)) // Only enable on boards that have seperate ENABLE_PINS
if(code_seen('E')) disable_e(); if(code_seen('E')) {
disable_e0();
disable_e1();
disable_e2();
}
#endif #endif
LCD_MESSAGEPGM("Partial Release"); LCD_MESSAGEPGM("Partial Release");
} }
@ -1100,7 +1123,9 @@ FORCE_INLINE void process_commands()
} }
} }
else if(code_seen('T')) {
else if(code_seen('T'))
{
tmp_extruder = code_value(); tmp_extruder = code_value();
if(tmp_extruder >= EXTRUDERS) { if(tmp_extruder >= EXTRUDERS) {
SERIAL_ECHO_START; SERIAL_ECHO_START;
@ -1110,8 +1135,12 @@ FORCE_INLINE void process_commands()
} }
else { else {
active_extruder = tmp_extruder; active_extruder = tmp_extruder;
SERIAL_ECHO_START;
SERIAL_ECHO("Active Extruder: ");
SERIAL_PROTOCOLLN((int)active_extruder);
} }
} }
else else
{ {
SERIAL_ECHO_START; SERIAL_ECHO_START;
@ -1219,8 +1248,8 @@ void manage_inactivity(byte debug)
if( (millis()-previous_millis_cmd) > EXTRUDER_RUNOUT_SECONDS*1000 ) if( (millis()-previous_millis_cmd) > EXTRUDER_RUNOUT_SECONDS*1000 )
if(degHotend(active_extruder)>EXTRUDER_RUNOUT_MINTEMP) if(degHotend(active_extruder)>EXTRUDER_RUNOUT_MINTEMP)
{ {
bool oldstatus=READ(E_ENABLE_PIN); bool oldstatus=READ(E0_ENABLE_PIN);
enable_e(); enable_e0();
float oldepos=current_position[E_AXIS]; float oldepos=current_position[E_AXIS];
float oldedes=destination[E_AXIS]; float oldedes=destination[E_AXIS];
plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS], plan_buffer_line(current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS],
@ -1232,7 +1261,7 @@ void manage_inactivity(byte debug)
previous_millis_cmd=millis(); previous_millis_cmd=millis();
//enquecommand(DEFAULT_STEPPER_DEACTIVE_COMMAND); //enquecommand(DEFAULT_STEPPER_DEACTIVE_COMMAND);
st_synchronize(); st_synchronize();
WRITE(E_ENABLE_PIN,oldstatus); WRITE(E0_ENABLE_PIN,oldstatus);
} }
#endif #endif
check_axes_activity(); check_axes_activity();
@ -1240,12 +1269,15 @@ void manage_inactivity(byte debug)
void kill() void kill()
{ {
cli(); // Stop interrupts
disable_heater(); disable_heater();
disable_x(); disable_x();
disable_y(); disable_y();
disable_z(); disable_z();
disable_e(); disable_e0();
disable_e1();
disable_e2();
if(PS_ON_PIN > -1) pinMode(PS_ON_PIN,INPUT); if(PS_ON_PIN > -1) pinMode(PS_ON_PIN,INPUT);
SERIAL_ERROR_START; SERIAL_ERROR_START;

2
Marlin/cardreader.pde
Unescape Escape View File

@ -442,4 +442,4 @@ void CardReader::printingHasFinished()
} }
autotempShutdown(); autotempShutdown();
} }
#endif //SDSUPPORT #endif //SDSUPPORT

5139
Marlin/fastio.h
View File

File diff suppressed because it is too large Load Diff

1430
Marlin/pins.h
View File

File diff suppressed because it is too large Load Diff

26
Marlin/planner.cpp
Unescape Escape View File

@ -56,9 +56,9 @@
//#include <math.h> //#include <math.h>
//#include <stdlib.h> //#include <stdlib.h>
#include "Marlin.h"
#include "Configuration.h" #include "Configuration.h"
#include "pins.h" #include "pins.h"
#include "Marlin.h"
#include "fastio.h" #include "fastio.h"
#include "planner.h" #include "planner.h"
#include "stepper.h" #include "stepper.h"
@ -81,8 +81,6 @@ float max_z_jerk;
float mintravelfeedrate; float mintravelfeedrate;
unsigned long axis_steps_per_sqr_second[NUM_AXIS]; unsigned long axis_steps_per_sqr_second[NUM_AXIS];
uint8_t active_extruder = 0;
// The current position of the tool in absolute steps // The current position of the tool in absolute steps
long position[4]; //rescaled from extern when axis_steps_per_unit are changed by gcode long position[4]; //rescaled from extern when axis_steps_per_unit are changed by gcode
static float previous_speed[4]; // Speed of previous path line segment static float previous_speed[4]; // Speed of previous path line segment
@ -95,7 +93,6 @@ static float previous_nominal_speed; // Nominal speed of previous path line segm
bool autotemp_enabled=false; bool autotemp_enabled=false;
#endif #endif
//=========================================================================== //===========================================================================
//=================semi-private variables, used in inline functions ===== //=================semi-private variables, used in inline functions =====
//=========================================================================== //===========================================================================
@ -196,8 +193,8 @@ void calculate_trapezoid_for_block(block_t *block, float entry_factor, float exi
} }
#ifdef ADVANCE #ifdef ADVANCE
long initial_advance = block->advance*entry_factor*entry_factor; volatile long initial_advance = block->advance*entry_factor*entry_factor;
long final_advance = block->advance*exit_factor*exit_factor; volatile long final_advance = block->advance*exit_factor*exit_factor;
#endif // ADVANCE #endif // ADVANCE
// block->accelerate_until = accelerate_steps; // block->accelerate_until = accelerate_steps;
@ -439,7 +436,7 @@ void check_axes_activity() {
if((DISABLE_X) && (x_active == 0)) disable_x(); if((DISABLE_X) && (x_active == 0)) disable_x();
if((DISABLE_Y) && (y_active == 0)) disable_y(); if((DISABLE_Y) && (y_active == 0)) disable_y();
if((DISABLE_Z) && (z_active == 0)) disable_z(); if((DISABLE_Z) && (z_active == 0)) disable_z();
if((DISABLE_E) && (e_active == 0)) disable_e(); if((DISABLE_E) && (e_active == 0)) { disable_e0();disable_e1();disable_e2(); }
} }
@ -514,15 +511,10 @@ void plan_buffer_line(const float &x, const float &y, const float &z, const floa
if(block->steps_x != 0) enable_x(); if(block->steps_x != 0) enable_x();
if(block->steps_y != 0) enable_y(); if(block->steps_y != 0) enable_y();
if(block->steps_z != 0) enable_z(); if(block->steps_z != 0) enable_z();
if(extruder == 0) {
if(block->steps_e != 0) enable_e(); // Enable all
} if(block->steps_e != 0) { enable_e0();enable_e1();enable_e2(); }
#if (EXTRUDERS > 1)
if(extruder == 1) {
if(block->steps_e != 0) enable_e1();
}
#endif
float delta_mm[4]; float delta_mm[4];
delta_mm[X_AXIS] = (target[X_AXIS]-position[X_AXIS])/axis_steps_per_unit[X_AXIS]; delta_mm[X_AXIS] = (target[X_AXIS]-position[X_AXIS])/axis_steps_per_unit[X_AXIS];
delta_mm[Y_AXIS] = (target[Y_AXIS]-position[Y_AXIS])/axis_steps_per_unit[Y_AXIS]; delta_mm[Y_AXIS] = (target[Y_AXIS]-position[Y_AXIS])/axis_steps_per_unit[Y_AXIS];
@ -809,4 +801,4 @@ void allow_cold_extrudes(bool allow)
#ifdef PREVENT_DANGEROUS_EXTRUDE #ifdef PREVENT_DANGEROUS_EXTRUDE
allow_cold_extrude=allow; allow_cold_extrude=allow;
#endif #endif
} }

2
Marlin/planner.h
Unescape Escape View File

@ -91,8 +91,6 @@ extern float max_z_jerk;
extern float mintravelfeedrate; extern float mintravelfeedrate;
extern unsigned long axis_steps_per_sqr_second[NUM_AXIS]; extern unsigned long axis_steps_per_sqr_second[NUM_AXIS];
extern uint8_t active_extruder;
#ifdef AUTOTEMP #ifdef AUTOTEMP
extern bool autotemp_enabled; extern bool autotemp_enabled;
extern float autotemp_max; extern float autotemp_max;

127
Marlin/stepper.cpp
Unescape Escape View File

@ -24,9 +24,9 @@
#include "stepper.h" #include "stepper.h"
#include "Configuration.h" #include "Configuration.h"
#include "pins.h"
#include "Marlin.h" #include "Marlin.h"
#include "planner.h" #include "planner.h"
#include "pins.h"
#include "fastio.h" #include "fastio.h"
#include "temperature.h" #include "temperature.h"
#include "ultralcd.h" #include "ultralcd.h"
@ -41,7 +41,6 @@
block_t *current_block; // A pointer to the block currently being traced block_t *current_block; // A pointer to the block currently being traced
//=========================================================================== //===========================================================================
//=============================private variables ============================ //=============================private variables ============================
//=========================================================================== //===========================================================================
@ -58,7 +57,7 @@ volatile static unsigned long step_events_completed; // The number of step event
static long advance_rate, advance, final_advance = 0; static long advance_rate, advance, final_advance = 0;
static long old_advance = 0; static long old_advance = 0;
#endif #endif
static long e_steps; static long e_steps[3];
static unsigned char busy = false; // TRUE when SIG_OUTPUT_COMPARE1A is being serviced. Used to avoid retriggering that handler. static unsigned char busy = false; // TRUE when SIG_OUTPUT_COMPARE1A is being serviced. Used to avoid retriggering that handler.
static long acceleration_time, deceleration_time; static long acceleration_time, deceleration_time;
//static unsigned long accelerate_until, decelerate_after, acceleration_rate, initial_rate, final_rate, nominal_rate; //static unsigned long accelerate_until, decelerate_after, acceleration_rate, initial_rate, final_rate, nominal_rate;
@ -267,7 +266,7 @@ FORCE_INLINE void trapezoid_generator_reset() {
advance = current_block->initial_advance; advance = current_block->initial_advance;
final_advance = current_block->final_advance; final_advance = current_block->final_advance;
// Do E steps + advance steps // Do E steps + advance steps
e_steps += ((advance >>8) - old_advance); e_steps[current_block->active_extruder] += ((advance >>8) - old_advance);
old_advance = advance >>8; old_advance = advance >>8;
#endif #endif
deceleration_time = 0; deceleration_time = 0;
@ -304,8 +303,8 @@ ISR(TIMER1_COMPA_vect)
counter_z = counter_x; counter_z = counter_x;
counter_e = counter_x; counter_e = counter_x;
step_events_completed = 0; step_events_completed = 0;
// #ifdef ADVANCE // #ifdef ADVANCE
e_steps = 0; // e_steps[current_block->active_extruder] = 0;
// #endif // #endif
} }
else { else {
@ -419,11 +418,11 @@ ISR(TIMER1_COMPA_vect)
#ifndef ADVANCE #ifndef ADVANCE
if ((out_bits & (1<<E_AXIS)) != 0) { // -direction if ((out_bits & (1<<E_AXIS)) != 0) { // -direction
WRITE(E_DIR_PIN,INVERT_E_DIR); REV_E_DIR();
count_direction[E_AXIS]=-1; count_direction[E_AXIS]=-1;
} }
else { // +direction else { // +direction
WRITE(E_DIR_PIN,!INVERT_E_DIR); NORM_E_DIR();
count_direction[E_AXIS]=-1; count_direction[E_AXIS]=-1;
} }
#endif //!ADVANCE #endif //!ADVANCE
@ -438,10 +437,10 @@ ISR(TIMER1_COMPA_vect)
if (counter_e > 0) { if (counter_e > 0) {
counter_e -= current_block->step_event_count; counter_e -= current_block->step_event_count;
if ((out_bits & (1<<E_AXIS)) != 0) { // - direction if ((out_bits & (1<<E_AXIS)) != 0) { // - direction
e_steps--; e_steps[current_block->active_extruder]--;
} }
else { else {
e_steps++; e_steps[current_block->active_extruder]++;
} }
} }
#endif //ADVANCE #endif //ADVANCE
@ -473,9 +472,9 @@ ISR(TIMER1_COMPA_vect)
#ifndef ADVANCE #ifndef ADVANCE
counter_e += current_block->steps_e; counter_e += current_block->steps_e;
if (counter_e > 0) { if (counter_e > 0) {
WRITE(E_STEP_PIN, HIGH); WRITE_E_STEP(HIGH);
counter_e -= current_block->step_event_count; counter_e -= current_block->step_event_count;
WRITE(E_STEP_PIN, LOW); WRITE_E_STEP(LOW);
count_position[E_AXIS]+=count_direction[E_AXIS]; count_position[E_AXIS]+=count_direction[E_AXIS];
} }
#endif //!ADVANCE #endif //!ADVANCE
@ -504,7 +503,7 @@ ISR(TIMER1_COMPA_vect)
} }
//if(advance > current_block->advance) advance = current_block->advance; //if(advance > current_block->advance) advance = current_block->advance;
// Do E steps + advance steps // Do E steps + advance steps
e_steps += ((advance >>8) - old_advance); e_steps[current_block->active_extruder] += ((advance >>8) - old_advance);
old_advance = advance >>8; old_advance = advance >>8;
#endif #endif
@ -533,7 +532,7 @@ ISR(TIMER1_COMPA_vect)
} }
if(advance < final_advance) advance = final_advance; if(advance < final_advance) advance = final_advance;
// Do E steps + advance steps // Do E steps + advance steps
e_steps += ((advance >>8) - old_advance); e_steps[current_block->active_extruder] += ((advance >>8) - old_advance);
old_advance = advance >>8; old_advance = advance >>8;
#endif //ADVANCE #endif //ADVANCE
} }
@ -558,27 +557,57 @@ ISR(TIMER1_COMPA_vect)
old_OCR0A += 52; // ~10kHz interrupt (250000 / 26 = 9615kHz) old_OCR0A += 52; // ~10kHz interrupt (250000 / 26 = 9615kHz)
OCR0A = old_OCR0A; OCR0A = old_OCR0A;
// Set E direction (Depends on E direction + advance) // Set E direction (Depends on E direction + advance)
for(unsigned char i=0; i<4;) { for(unsigned char i=0; i<4;i++) {
WRITE(E_STEP_PIN, LOW); if (e_steps[0] != 0) {
if (e_steps == 0) break; WRITE(E0_STEP_PIN, LOW);
i++; if (e_steps[0] < 0) {
if (e_steps < 0) { WRITE(E0_DIR_PIN, INVERT_E0_DIR);
WRITE(E_DIR_PIN,INVERT_E_DIR); e_steps[0]++;
e_steps++; WRITE(E0_STEP_PIN, HIGH);
WRITE(E_STEP_PIN, HIGH); }
} else if (e_steps[0] > 0) {
else if (e_steps > 0) { WRITE(E0_DIR_PIN, !INVERT_E0_DIR);
WRITE(E_DIR_PIN,!INVERT_E_DIR); e_steps[0]--;
e_steps--; WRITE(E0_STEP_PIN, HIGH);
WRITE(E_STEP_PIN, HIGH); }
}
#if EXTRUDERS > 1
if (e_steps[1] != 0) {
WRITE(E1_STEP_PIN, LOW);
if (e_steps[1] < 0) {
WRITE(E1_DIR_PIN, INVERT_E1_DIR);
e_steps[1]++;
WRITE(E1_STEP_PIN, HIGH);
}
else if (e_steps[1] > 0) {
WRITE(E1_DIR_PIN, !INVERT_E1_DIR);
e_steps[1]--;
WRITE(E1_STEP_PIN, HIGH);
}
}
#endif
#if EXTRUDERS > 2
if (e_steps[2] != 0) {
WRITE(E2_STEP_PIN, LOW);
if (e_steps[2] < 0) {
WRITE(E2_DIR_PIN, INVERT_E2_DIR);
e_steps[2]++;
WRITE(E2_STEP_PIN, HIGH);
}
else if (e_steps[2] > 0) {
WRITE(E2_DIR_PIN, !INVERT_E2_DIR);
e_steps[2]--;
WRITE(E2_STEP_PIN, HIGH);
}
} }
#endif
} }
} }
#endif // ADVANCE #endif // ADVANCE
void st_init() void st_init()
{ {
//Initialize Dir Pins //Initialize Dir Pins
#if X_DIR_PIN > -1 #if X_DIR_PIN > -1
SET_OUTPUT(X_DIR_PIN); SET_OUTPUT(X_DIR_PIN);
#endif #endif
@ -588,8 +617,14 @@ void st_init()
#if Z_DIR_PIN > -1 #if Z_DIR_PIN > -1
SET_OUTPUT(Z_DIR_PIN); SET_OUTPUT(Z_DIR_PIN);
#endif #endif
#if E_DIR_PIN > -1 #if E0_DIR_PIN > -1
SET_OUTPUT(E_DIR_PIN); SET_OUTPUT(E0_DIR_PIN);
#endif
#if defined(E1_DIR_PIN) && (E1_DIR_PIN > -1)
SET_OUTPUT(E1_DIR_PIN);
#endif
#if defined(E2_DIR_PIN) && (E2_DIR_PIN > -1)
SET_OUTPUT(E2_DIR_PIN);
#endif #endif
//Initialize Enable Pins - steppers default to disabled. //Initialize Enable Pins - steppers default to disabled.
@ -606,9 +641,17 @@ void st_init()
SET_OUTPUT(Z_ENABLE_PIN); SET_OUTPUT(Z_ENABLE_PIN);
if(!Z_ENABLE_ON) WRITE(Z_ENABLE_PIN,HIGH); if(!Z_ENABLE_ON) WRITE(Z_ENABLE_PIN,HIGH);
#endif #endif
#if (E_ENABLE_PIN > -1) #if (E0_ENABLE_PIN > -1)
SET_OUTPUT(E_ENABLE_PIN); SET_OUTPUT(E0_ENABLE_PIN);
if(!E_ENABLE_ON) WRITE(E_ENABLE_PIN,HIGH); if(!E_ENABLE_ON) WRITE(E0_ENABLE_PIN,HIGH);
#endif
#if defined(E1_ENABLE_PIN) && (E1_ENABLE_PIN > -1)
SET_OUTPUT(E1_ENABLE_PIN);
if(!E_ENABLE_ON) WRITE(E1_ENABLE_PIN,HIGH);
#endif
#if defined(E2_ENABLE_PIN) && (E2_ENABLE_PIN > -1)
SET_OUTPUT(E2_ENABLE_PIN);
if(!E_ENABLE_ON) WRITE(E2_ENABLE_PIN,HIGH);
#endif #endif
//endstops and pullups //endstops and pullups
@ -669,8 +712,14 @@ void st_init()
#if (Z_STEP_PIN > -1) #if (Z_STEP_PIN > -1)
SET_OUTPUT(Z_STEP_PIN); SET_OUTPUT(Z_STEP_PIN);
#endif #endif
#if (E_STEP_PIN > -1) #if (E0_STEP_PIN > -1)
SET_OUTPUT(E_STEP_PIN); SET_OUTPUT(E0_STEP_PIN);
#endif
#if defined(E1_STEP_PIN) && (E1_STEP_PIN > -1)
SET_OUTPUT(E1_STEP_PIN);
#endif
#if defined(E2_STEP_PIN) && (E2_STEP_PIN > -1)
SET_OUTPUT(E2_STEP_PIN);
#endif #endif
// waveform generation = 0100 = CTC // waveform generation = 0100 = CTC
@ -693,7 +742,9 @@ void st_init()
TCCR0A &= ~(1<<WGM01); TCCR0A &= ~(1<<WGM01);
TCCR0A &= ~(1<<WGM00); TCCR0A &= ~(1<<WGM00);
#endif #endif
e_steps = 0; e_steps[0] = 0;
e_steps[1] = 0;
e_steps[2] = 0;
TIMSK0 |= (1<<OCIE0A); TIMSK0 |= (1<<OCIE0A);
#endif //ADVANCE #endif //ADVANCE
@ -750,7 +801,9 @@ void finishAndDisableSteppers()
disable_x(); disable_x();
disable_y(); disable_y();
disable_z(); disable_z();
disable_e(); disable_e0();
disable_e1();
disable_e2();
} }
void quickStop() void quickStop()

15
Marlin/stepper.h
Unescape Escape View File

@ -23,6 +23,21 @@
#include "planner.h" #include "planner.h"
#if EXTRUDERS > 2
#define WRITE_E_STEP(v) { if(current_block->active_extruder == 2) { WRITE(E2_STEP_PIN, v); } else { if(current_block->active_extruder == 1) { WRITE(E1_STEP_PIN, v); } else { WRITE(E0_STEP_PIN, v); }}}
#define NORM_E_DIR() { if(current_block->active_extruder == 2) { WRITE(!E2_DIR_PIN, INVERT_E2_DIR); } else { if(current_block->active_extruder == 1) { WRITE(!E1_DIR_PIN, INVERT_E1_DIR); } else { WRITE(E0_DIR_PIN, !INVERT_E0_DIR); }}}
#define REV_E_DIR() { if(current_block->active_extruder == 2) { WRITE(E2_DIR_PIN, INVERT_E2_DIR); } else { if(current_block->active_extruder == 1) { WRITE(E1_DIR_PIN, INVERT_E1_DIR); } else { WRITE(E0_DIR_PIN, INVERT_E0_DIR); }}}
#elif EXTRUDERS > 1
#define WRITE_E_STEP(v) { if(current_block->active_extruder == 1) { WRITE(E1_STEP_PIN, v); } else { WRITE(E0_STEP_PIN, v); }}
#define NORM_E_DIR() { if(current_block->active_extruder == 1) { WRITE(E1_DIR_PIN, !INVERT_E1_DIR); } else { WRITE(E0_DIR_PIN, !INVERT_E0_DIR); }}
#define REV_E_DIR() { if(current_block->active_extruder == 1) { WRITE(E1_DIR_PIN, INVERT_E1_DIR); } else { WRITE(E0_DIR_PIN, INVERT_E0_DIR); }}
#else
#define WRITE_E_STEP(v) WRITE(E0_STEP_PIN, v)
#define NORM_E_DIR() WRITE(E0_DIR_PIN, !INVERT_E0_DIR)
#define REV_E_DIR() WRITE(E0_DIR_PIN, INVERT_E0_DIR)
#endif
// Initialize and start the stepper motor subsystem // Initialize and start the stepper motor subsystem
void st_init(); void st_init();

547
Marlin/temperature.cpp
Unescape Escape View File

@ -26,7 +26,6 @@
It has preliminary support for Matthew Roberts advance algorithm It has preliminary support for Matthew Roberts advance algorithm
http://reprap.org/pipermail/reprap-dev/2011-May/003323.html http://reprap.org/pipermail/reprap-dev/2011-May/003323.html
This firmware is optimized for gen6 electronics.
*/ */
#include <avr/pgmspace.h> #include <avr/pgmspace.h>
@ -41,17 +40,14 @@
//=========================================================================== //===========================================================================
//=============================public variables============================ //=============================public variables============================
//=========================================================================== //===========================================================================
int target_raw[3] = {0, 0, 0}; int target_raw[EXTRUDERS] = { 0 };
int current_raw[3] = {0, 0, 0}; int target_raw_bed = 0;
int heatingtarget_raw[3]= {0, 0, 0}; int current_raw[EXTRUDERS] = { 0 };
int current_raw_bed = 0;
#ifdef PIDTEMP #ifdef PIDTEMP
// used external
// probably used external float pid_setpoint[EXTRUDERS] = { 0.0 };
float HeaterPower;
float pid_setpoint = 0.0;
float Kp=DEFAULT_Kp; float Kp=DEFAULT_Kp;
float Ki=DEFAULT_Ki; float Ki=DEFAULT_Ki;
@ -72,45 +68,83 @@ static unsigned long previous_millis_bed_heater;
#ifdef PIDTEMP #ifdef PIDTEMP
//static cannot be external: //static cannot be external:
static float temp_iState = 0; static float temp_iState[EXTRUDERS] = { 0 };
static float temp_dState = 0; static float temp_dState[EXTRUDERS] = { 0 };
static float pTerm; static float pTerm[EXTRUDERS];
static float iTerm; static float iTerm[EXTRUDERS];
static float dTerm; static float dTerm[EXTRUDERS];
//int output; //int output;
static float pid_error; static float pid_error[EXTRUDERS];
static float temp_iState_min; static float temp_iState_min[EXTRUDERS];
static float temp_iState_max; static float temp_iState_max[EXTRUDERS];
// static float pid_input; // static float pid_input[EXTRUDERS];
// static float pid_output; // static float pid_output[EXTRUDERS];
static bool pid_reset; static bool pid_reset[EXTRUDERS];
#endif //PIDTEMP #endif //PIDTEMP
static unsigned char soft_pwm[EXTRUDERS];
#ifdef WATCHPERIOD #ifdef WATCHPERIOD
static int watch_raw[EXTRUDERS] = { -1000 }; // the first value used for all
static int watch_oldtemp[3] = {0,0,0}; static int watch_oldtemp[3] = {0,0,0};
static unsigned long watchmillis = 0; static unsigned long watchmillis = 0;
#endif //WATCHPERIOD #endif //WATCHPERIOD
// Init min and max temp with extreme values to prevent false errors during startup // Init min and max temp with extreme values to prevent false errors during startup
static int minttemp_0 = 0; static int minttemp[EXTRUDERS] = { 0 };
static int maxttemp_0 = 16383; static int maxttemp[EXTRUDERS] = { 16383 }; // the first value used for all
//static int minttemp_1 = 0;
//static int maxttemp_1 = 16383;
static int bed_minttemp = 0; static int bed_minttemp = 0;
static int bed_maxttemp = 16383; static int bed_maxttemp = 16383;
static int heater_pin_map[EXTRUDERS] = { HEATER_0_PIN
#if EXTRUDERS > 1
, HEATER_1_PIN
#endif
#if EXTRUDERS > 2
, HEATER_2_PIN
#endif
#if EXTRUDERS > 3
#error Unsupported number of extruders
#endif
};
static void *heater_ttbl_map[EXTRUDERS] = { (void *)heater_0_temptable
#if EXTRUDERS > 1
, (void *)heater_1_temptable
#endif
#if EXTRUDERS > 2
, (void *)heater_2_temptable
#endif
#if EXTRUDERS > 3
#error Unsupported number of extruders
#endif
};
static int heater_ttbllen_map[EXTRUDERS] = { heater_0_temptable_len
#if EXTRUDERS > 1
, heater_1_temptable_len
#endif
#if EXTRUDERS > 2
, heater_2_temptable_len
#endif
#if EXTRUDERS > 3
#error Unsupported number of extruders
#endif
};
//=========================================================================== //===========================================================================
//=============================functions ============================ //============================= functions ============================
//=========================================================================== //===========================================================================
void updatePID() void updatePID()
{ {
#ifdef PIDTEMP #ifdef PIDTEMP
temp_iState_max = PID_INTEGRAL_DRIVE_MAX / Ki; for(int e = 0; e < EXTRUDERS; e++) {
temp_iState_max[e] = PID_INTEGRAL_DRIVE_MAX / Ki;
}
#endif #endif
} }
int getHeaterPower(int heater) {
return soft_pwm[heater];
}
void manage_heater() void manage_heater()
{ {
#ifdef USE_WATCHDOG #ifdef USE_WATCHDOG
@ -119,73 +153,67 @@ void manage_heater()
float pid_input; float pid_input;
float pid_output; float pid_output;
if(temp_meas_ready != true) //better readability if(temp_meas_ready != true) //better readability
return; return;
CRITICAL_SECTION_START; CRITICAL_SECTION_START;
temp_meas_ready = false; temp_meas_ready = false;
CRITICAL_SECTION_END; CRITICAL_SECTION_END;
for(int e = 0; e < EXTRUDERS; e++)
{
#ifdef PIDTEMP #ifdef PIDTEMP
pid_input = analog2temp(current_raw[TEMPSENSOR_HOTEND_0]); pid_input = analog2temp(current_raw[e], e);
#ifndef PID_OPENLOOP #ifndef PID_OPENLOOP
pid_error = pid_setpoint - pid_input; pid_error[e] = pid_setpoint[e] - pid_input;
if(pid_error > 10){ if(pid_error[e] > 10) {
pid_output = PID_MAX; pid_output = PID_MAX;
pid_reset = true; pid_reset[e] = true;
} }
else if(pid_error < -10) { else if(pid_error[e] < -10) {
pid_output = 0; pid_output = 0;
pid_reset = true; pid_reset[e] = true;
} }
else { else {
if(pid_reset == true) { if(pid_reset[e] == true) {
temp_iState = 0.0; temp_iState[e] = 0.0;
pid_reset = false; pid_reset[e] = false;
} }
pTerm = Kp * pid_error; pTerm[e] = Kp * pid_error[e];
temp_iState += pid_error; temp_iState[e] += pid_error[e];
temp_iState = constrain(temp_iState, temp_iState_min, temp_iState_max); temp_iState[e] = constrain(temp_iState[e], temp_iState_min[e], temp_iState_max[e]);
iTerm = Ki * temp_iState; iTerm[e] = Ki * temp_iState[e];
//K1 defined in Configuration.h in the PID settings //K1 defined in Configuration.h in the PID settings
#define K2 (1.0-K1) #define K2 (1.0-K1)
dTerm = (Kd * (pid_input - temp_dState))*K2 + (K1 * dTerm); dTerm[e] = (Kd * (pid_input - temp_dState[e]))*K2 + (K1 * dTerm[e]);
temp_dState = pid_input; temp_dState[e] = pid_input;
// #ifdef PID_ADD_EXTRUSION_RATE pid_output = constrain(pTerm[e] + iTerm[e] - dTerm[e], 0, PID_MAX);
// pTerm+=Kc*current_block->speed_e; //additional heating if extrusion speed is high
// #endif
pid_output = constrain(pTerm + iTerm - dTerm, 0, PID_MAX);
} }
#endif //PID_OPENLOOP #endif //PID_OPENLOOP
#ifdef PID_DEBUG #ifdef PID_DEBUG
//SERIAL_ECHOLN(" PIDDEBUG Input "<<pid_input<<" Output "<<pid_output" pTerm "<<pTerm<<" iTerm "<<iTerm<<" dTerm "<<dTerm); SERIAL_ECHOLN(" PIDDEBUG "<<e<<": Input "<<pid_input<<" Output "<<pid_output" pTerm "<<pTerm[e]<<" iTerm "<<iTerm[e]<<" dTerm "<<dTerm[e]);
#endif //PID_DEBUG #endif //PID_DEBUG
HeaterPower=pid_output; #else /* PID off */
// Check if temperature is within the correct range pid_output = 0;
if((current_raw[TEMPSENSOR_HOTEND_0] > minttemp_0) && (current_raw[TEMPSENSOR_HOTEND_0] < maxttemp_0)) { if(current_raw[e] < target_raw[e]) {
analogWrite(HEATER_0_PIN, pid_output); pid_output = PID_MAX;
} }
else { #endif
analogWrite(HEATER_0_PIN, 0);
}
#endif //PIDTEMP
#ifndef PIDTEMP
// Check if temperature is within the correct range // Check if temperature is within the correct range
if((current_raw[TEMPSENSOR_HOTEND_0] > minttemp_0) && (current_raw[TEMPSENSOR_HOTEND_0] < maxttemp_0)) { if((current_raw[e] > minttemp[e]) && (current_raw[e] < maxttemp[e]))
if(current_raw[TEMPSENSOR_HOTEND_0] >= target_raw[TEMPSENSOR_HOTEND_0]) { {
WRITE(HEATER_0_PIN,LOW); //analogWrite(heater_pin_map[e], pid_output);
} soft_pwm[e] = (int)pid_output >> 1;
else {
WRITE(HEATER_0_PIN,HIGH);
}
} }
else { else {
WRITE(HEATER_0_PIN,LOW); //analogWrite(heater_pin_map[e], 0);
} soft_pwm[e] = 0;
#endif }
} // End extruder for loop
#ifdef WATCHPERIOD #ifdef WATCHPERIOD
if(watchmillis && millis() - watchmillis > WATCHPERIOD){ if(watchmillis && millis() - watchmillis > WATCHPERIOD){
@ -204,20 +232,20 @@ void manage_heater()
return; return;
previous_millis_bed_heater = millis(); previous_millis_bed_heater = millis();
#if TEMP_1_PIN > -1 #if TEMP_BED_PIN > -1
// Check if temperature is within the correct range // Check if temperature is within the correct range
if((current_raw[TEMPSENSOR_BED] > bed_minttemp) && (current_raw[TEMPSENSOR_BED] < bed_maxttemp)) { if((current_raw_bed > bed_minttemp) && (current_raw_bed < bed_maxttemp)) {
if(current_raw[TEMPSENSOR_BED] >= target_raw[TEMPSENSOR_BED]) if(current_raw_bed >= target_raw_bed)
{ {
WRITE(HEATER_1_PIN,LOW); WRITE(HEATER_BED_PIN,LOW);
} }
else else
{ {
WRITE(HEATER_1_PIN,HIGH); WRITE(HEATER_BED_PIN,HIGH);
} }
} }
else { else {
WRITE(HEATER_1_PIN,LOW); WRITE(HEATER_BED_PIN,LOW);
} }
#endif #endif
} }
@ -227,30 +255,38 @@ void manage_heater()
// For a thermistor, it uses the RepRap thermistor temp table. // For a thermistor, it uses the RepRap thermistor temp table.
// This is needed because PID in hydra firmware hovers around a given analog value, not a temp value. // This is needed because PID in hydra firmware hovers around a given analog value, not a temp value.
// This function is derived from inversing the logic from a portion of getTemperature() in FiveD RepRap firmware. // This function is derived from inversing the logic from a portion of getTemperature() in FiveD RepRap firmware.
int temp2analog(int celsius) { int temp2analog(int celsius, uint8_t e) {
#ifdef HEATER_0_USES_THERMISTOR if(e >= EXTRUDERS)
{
SERIAL_ERROR_START;
SERIAL_ERROR((int)e);
SERIAL_ERRORLNPGM(" - Invalid extruder number!");
kill();
}
if(heater_ttbl_map[e] != 0)
{
int raw = 0; int raw = 0;
byte i; byte i;
short (*tt)[][2] = (short (*)[][2])(heater_ttbl_map[e]);
for (i=1; i<NUMTEMPS_HEATER_0; i++) for (i=1; i<heater_ttbllen_map[e]; i++)
{ {
if (PGM_RD_W(heater_0_temptable[i][1]) < celsius) if (PGM_RD_W((*tt)[i][1]) < celsius)
{ {
raw = PGM_RD_W(heater_0_temptable[i-1][0]) + raw = PGM_RD_W((*tt)[i-1][0]) +
(celsius - PGM_RD_W(heater_0_temptable[i-1][1])) * (celsius - PGM_RD_W((*tt)[i-1][1])) *
(PGM_RD_W(heater_0_temptable[i][0]) - PGM_RD_W(heater_0_temptable[i-1][0])) / (PGM_RD_W((*tt)[i][0]) - PGM_RD_W((*tt)[i-1][0])) /
(PGM_RD_W(heater_0_temptable[i][1]) - PGM_RD_W(heater_0_temptable[i-1][1])); (PGM_RD_W((*tt)[i][1]) - PGM_RD_W((*tt)[i-1][1]));
break; break;
} }
} }
// Overflow: Set to last value in the table // Overflow: Set to last value in the table
if (i == NUMTEMPS_HEATER_0) raw = PGM_RD_W(heater_0_temptable[i-1][0]); if (i == heater_ttbllen_map[e]) raw = PGM_RD_W((*tt)[i-1][0]);
return (1023 * OVERSAMPLENR) - raw; return (1023 * OVERSAMPLENR) - raw;
#elif defined HEATER_0_USES_AD595 }
return celsius * (1024.0 / (5.0 * 100.0) ) * OVERSAMPLENR; return celsius * (1024.0 / (5.0 * 100.0) ) * OVERSAMPLENR;
#endif
} }
// Takes bed temperature value as input and returns corresponding raw value. // Takes bed temperature value as input and returns corresponding raw value.
@ -258,12 +294,11 @@ int temp2analog(int celsius) {
// This is needed because PID in hydra firmware hovers around a given analog value, not a temp value. // This is needed because PID in hydra firmware hovers around a given analog value, not a temp value.
// This function is derived from inversing the logic from a portion of getTemperature() in FiveD RepRap firmware. // This function is derived from inversing the logic from a portion of getTemperature() in FiveD RepRap firmware.
int temp2analogBed(int celsius) { int temp2analogBed(int celsius) {
#ifdef BED_USES_THERMISTOR #ifdef BED_USES_THERMISTOR
int raw = 0; int raw = 0;
byte i; byte i;
for (i=1; i<BNUMTEMPS; i++) for (i=1; i<bedtemptable_len; i++)
{ {
if (PGM_RD_W(bedtemptable[i][1]) < celsius) if (PGM_RD_W(bedtemptable[i][1]) < celsius)
{ {
@ -277,45 +312,52 @@ int temp2analogBed(int celsius) {
} }
// Overflow: Set to last value in the table // Overflow: Set to last value in the table
if (i == BNUMTEMPS) raw = PGM_RD_W(bedtemptable[i-1][0]); if (i == bedtemptable_len) raw = PGM_RD_W(bedtemptable[i-1][0]);
return (1023 * OVERSAMPLENR) - raw; return (1023 * OVERSAMPLENR) - raw;
#elif defined BED_USES_AD595 #elif defined BED_USES_AD595
return lround(celsius * (1024.0 * OVERSAMPLENR/ (5.0 * 100.0) ) ); return lround(celsius * (1024.0 * OVERSAMPLENR/ (5.0 * 100.0) ) );
#else #else
#warning No heater-type defined for the bed. #warning No heater-type defined for the bed.
#endif return 0;
return 0; #endif
} }
// Derived from RepRap FiveD extruder::getTemperature() // Derived from RepRap FiveD extruder::getTemperature()
// For hot end temperature measurement. // For hot end temperature measurement.
float analog2temp(int raw) { float analog2temp(int raw, uint8_t e) {
#ifdef HEATER_0_USES_THERMISTOR if(e >= EXTRUDERS)
{
SERIAL_ERROR_START;
SERIAL_ERROR((int)e);
SERIAL_ERRORLNPGM(" - Invalid extruder number !");
kill();
}
if(heater_ttbl_map[e] != 0)
{
float celsius = 0; float celsius = 0;
byte i; byte i;
short (*tt)[][2] = (short (*)[][2])(heater_ttbl_map[e]);
raw = (1023 * OVERSAMPLENR) - raw; raw = (1023 * OVERSAMPLENR) - raw;
for (i=1; i<NUMTEMPS_HEATER_0; i++) for (i=1; i<heater_ttbllen_map[e]; i++)
{ {
if (PGM_RD_W(heater_0_temptable[i][0]) > raw) if (PGM_RD_W((*tt)[i][0]) > raw)
{ {
celsius = PGM_RD_W(heater_0_temptable[i-1][1]) + celsius = PGM_RD_W((*tt)[i-1][1]) +
(raw - PGM_RD_W(heater_0_temptable[i-1][0])) * (raw - PGM_RD_W((*tt)[i-1][0])) *
(float)(PGM_RD_W(heater_0_temptable[i][1]) - PGM_RD_W(heater_0_temptable[i-1][1])) / (float)(PGM_RD_W((*tt)[i][1]) - PGM_RD_W((*tt)[i-1][1])) /
(float)(PGM_RD_W(heater_0_temptable[i][0]) - PGM_RD_W(heater_0_temptable[i-1][0])); (float)(PGM_RD_W((*tt)[i][0]) - PGM_RD_W((*tt)[i-1][0]));
break; break;
} }
} }
// Overflow: Set to last value in the table // Overflow: Set to last value in the table
if (i == NUMTEMPS_HEATER_0) celsius = PGM_RD_W(heater_0_temptable[i-1][1]); if (i == heater_ttbllen_map[e]) celsius = PGM_RD_W((*tt)[i-1][1]);
return celsius; return celsius;
#elif defined HEATER_0_USES_AD595 }
return raw * ((5.0 * 100.0) / 1024.0) / OVERSAMPLENR; return raw * ((5.0 * 100.0) / 1024.0) / OVERSAMPLENR;
#else
#error PLEASE DEFINE HEATER TYPE
#endif
} }
// Derived from RepRap FiveD extruder::getTemperature() // Derived from RepRap FiveD extruder::getTemperature()
@ -327,7 +369,7 @@ float analog2tempBed(int raw) {
raw = (1023 * OVERSAMPLENR) - raw; raw = (1023 * OVERSAMPLENR) - raw;
for (i=1; i<BNUMTEMPS; i++) for (i=1; i<bedtemptable_len; i++)
{ {
if (PGM_RD_W(bedtemptable[i][0]) > raw) if (PGM_RD_W(bedtemptable[i][0]) > raw)
{ {
@ -341,7 +383,7 @@ float analog2tempBed(int raw) {
} }
// Overflow: Set to last value in the table // Overflow: Set to last value in the table
if (i == BNUMTEMPS) celsius = PGM_RD_W(bedtemptable[i-1][1]); if (i == bedtemptable_len) celsius = PGM_RD_W(bedtemptable[i-1][1]);
return celsius; return celsius;
@ -355,6 +397,19 @@ float analog2tempBed(int raw) {
void tp_init() void tp_init()
{ {
// Finish init of mult extruder arrays
for(int e = 0; e < EXTRUDERS; e++) {
// populate with the first value
#ifdef WATCHPERIOD
watch_raw[e] = watch_raw[0];
#endif
maxttemp[e] = maxttemp[0];
#ifdef PIDTEMP
temp_iState_min[e] = 0.0;
temp_iState_max[e] = PID_INTEGRAL_DRIVE_MAX / Ki;
#endif //PIDTEMP
}
#if (HEATER_0_PIN > -1) #if (HEATER_0_PIN > -1)
SET_OUTPUT(HEATER_0_PIN); SET_OUTPUT(HEATER_0_PIN);
#endif #endif
@ -364,11 +419,12 @@ void tp_init()
#if (HEATER_2_PIN > -1) #if (HEATER_2_PIN > -1)
SET_OUTPUT(HEATER_2_PIN); SET_OUTPUT(HEATER_2_PIN);
#endif #endif
#if (HEATER_BED_PIN > -1)
#ifdef PIDTEMP SET_OUTPUT(HEATER_BED_PIN);
temp_iState_min = 0.0; #endif
temp_iState_max = PID_INTEGRAL_DRIVE_MAX / Ki; #if (FAN_PIN > -1)
#endif //PIDTEMP SET_OUTPUT(FAN_PIN);
#endif
// Set analog inputs // Set analog inputs
ADCSRA = 1<<ADEN | 1<<ADSC | 1<<ADIF | 0x07; ADCSRA = 1<<ADEN | 1<<ADSC | 1<<ADIF | 0x07;
@ -381,7 +437,6 @@ void tp_init()
DIDR0 |= 1 << TEMP_0_PIN; DIDR0 |= 1 << TEMP_0_PIN;
#else #else
DIDR2 |= 1<<(TEMP_0_PIN - 8); DIDR2 |= 1<<(TEMP_0_PIN - 8);
ADCSRB = 1<<MUX5;
#endif #endif
#endif #endif
#if (TEMP_1_PIN > -1) #if (TEMP_1_PIN > -1)
@ -389,7 +444,6 @@ void tp_init()
DIDR0 |= 1<<TEMP_1_PIN; DIDR0 |= 1<<TEMP_1_PIN;
#else #else
DIDR2 |= 1<<(TEMP_1_PIN - 8); DIDR2 |= 1<<(TEMP_1_PIN - 8);
ADCSRB = 1<<MUX5;
#endif #endif
#endif #endif
#if (TEMP_2_PIN > -1) #if (TEMP_2_PIN > -1)
@ -397,7 +451,13 @@ void tp_init()
DIDR0 |= 1 << TEMP_2_PIN; DIDR0 |= 1 << TEMP_2_PIN;
#else #else
DIDR2 = 1<<(TEMP_2_PIN - 8); DIDR2 = 1<<(TEMP_2_PIN - 8);
ADCSRB = 1<<MUX5; #endif
#endif
#if (TEMP_BED_PIN > -1)
#if TEMP_BED_PIN < 8
DIDR0 |= 1<<TEMP_BED_PIN;
#else
DIDR2 |= 1<<(TEMP_BED_PIN - 8);
#endif #endif
#endif #endif
@ -407,27 +467,34 @@ void tp_init()
TIMSK0 |= (1<<OCIE0B); TIMSK0 |= (1<<OCIE0B);
// Wait for temperature measurement to settle // Wait for temperature measurement to settle
delay(200); delay(250);
#ifdef HEATER_0_MINTEMP #ifdef HEATER_0_MINTEMP
minttemp_0 = temp2analog(HEATER_0_MINTEMP); minttemp[0] = temp2analog(HEATER_0_MINTEMP, 0);
#endif //MINTEMP #endif //MINTEMP
#ifdef HEATER_0_MAXTEMP #ifdef HEATER_0_MAXTEMP
maxttemp_0 = temp2analog(HEATER_0_MAXTEMP); maxttemp[0] = temp2analog(HEATER_0_MAXTEMP, 0);
#endif //MAXTEMP #endif //MAXTEMP
#ifdef HEATER_1_MINTEMP #if (EXTRUDERS > 1) && defined(HEATER_1_MINTEMP)
minttemp_1 = temp2analog(HEATER_1_MINTEMP); minttemp[1] = temp2analog(HEATER_1_MINTEMP, 1);
#endif //MINTEMP #endif // MINTEMP 1
#ifdef HEATER_1_MAXTEMP #if (EXTRUDERS > 1) && defined(HEATER_1_MAXTEMP)
maxttemp_1 = temp2analog(HEATER_1_MAXTEMP); maxttemp[1] = temp2analog(HEATER_1_MAXTEMP, 1);
#endif //MAXTEMP #endif //MAXTEMP 1
#if (EXTRUDERS > 2) && defined(HEATER_2_MINTEMP)
minttemp[2] = temp2analog(HEATER_2_MINTEMP, 2);
#endif //MINTEMP 2
#if (EXTRUDERS > 2) && defined(HEATER_2_MAXTEMP)
maxttemp[2] = temp2analog(HEATER_2_MAXTEMP, 2);
#endif //MAXTEMP 2
#ifdef BED_MINTEMP #ifdef BED_MINTEMP
bed_minttemp = temp2analog(BED_MINTEMP); bed_minttemp = temp2analogBed(BED_MINTEMP);
#endif //BED_MINTEMP #endif //BED_MINTEMP
#ifdef BED_MAXTEMP #ifdef BED_MAXTEMP
bed_maxttemp = temp2analog(BED_MAXTEMP); bed_maxttemp = temp2analogBed(BED_MAXTEMP);
#endif //BED_MAXTEMP #endif //BED_MAXTEMP
} }
@ -436,15 +503,17 @@ void tp_init()
void setWatch() void setWatch()
{ {
#ifdef WATCHPERIOD #ifdef WATCHPERIOD
if(isHeatingHotend0()) int t = 0;
for (int e = 0; e < EXTRUDERS; e++)
{ {
watchmillis = max(1,millis()); if(isHeatingHotend(e))
watch_oldtemp[TEMPSENSOR_HOTEND_0] = degHotend(0); watch_oldtemp[TEMPSENSOR_HOTEND_0] = degHotend(0);
{
t = max(t,millis());
watch_raw[e] = current_raw[e];
}
} }
else watchmillis = t;
{
watchmillis = 0;
}
#endif #endif
} }
@ -453,6 +522,7 @@ void disable_heater()
{ {
#if TEMP_0_PIN > -1 #if TEMP_0_PIN > -1
target_raw[0]=0; target_raw[0]=0;
soft_pwm[0]=0;
#if HEATER_0_PIN > -1 #if HEATER_0_PIN > -1
digitalWrite(HEATER_0_PIN,LOW); digitalWrite(HEATER_0_PIN,LOW);
#endif #endif
@ -460,6 +530,7 @@ void disable_heater()
#if TEMP_1_PIN > -1 #if TEMP_1_PIN > -1
target_raw[1]=0; target_raw[1]=0;
soft_pwm[1]=0;
#if HEATER_1_PIN > -1 #if HEATER_1_PIN > -1
digitalWrite(HEATER_1_PIN,LOW); digitalWrite(HEATER_1_PIN,LOW);
#endif #endif
@ -467,10 +538,38 @@ void disable_heater()
#if TEMP_2_PIN > -1 #if TEMP_2_PIN > -1
target_raw[2]=0; target_raw[2]=0;
soft_pwm[2]=0;
#if HEATER_2_PIN > -1 #if HEATER_2_PIN > -1
digitalWrite(HEATER_2_PIN,LOW); digitalWrite(HEATER_2_PIN,LOW);
#endif #endif
#endif #endif
#if TEMP_BED_PIN > -1
target_raw_bed=0;
#if HEATER_BED_PIN > -1
digitalWrite(HEATER_BED_PIN,LOW);
#endif
#endif
}
void max_temp_error(uint8_t e) {
digitalWrite(heater_pin_map[e], 0);
SERIAL_ERROR_START;
SERIAL_ERRORLN(e);
SERIAL_ERRORLNPGM(": Extruder switched off. MAXTEMP triggered !");
}
void min_temp_error(uint8_t e) {
digitalWrite(heater_pin_map[e], 0);
SERIAL_ERROR_START;
SERIAL_ERRORLN(e);
SERIAL_ERRORLNPGM(": Extruder switched off. MINTEMP triggered !");
}
void bed_max_temp_error(void) {
digitalWrite(HEATER_BED_PIN, 0);
SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temperature heated bed switched off. MAXTEMP triggered !!");
} }
// Timer 0 is shared with millies // Timer 0 is shared with millies
@ -481,7 +580,35 @@ ISR(TIMER0_COMPB_vect)
static unsigned long raw_temp_0_value = 0; static unsigned long raw_temp_0_value = 0;
static unsigned long raw_temp_1_value = 0; static unsigned long raw_temp_1_value = 0;
static unsigned long raw_temp_2_value = 0; static unsigned long raw_temp_2_value = 0;
static unsigned long raw_temp_bed_value = 0;
static unsigned char temp_state = 0; static unsigned char temp_state = 0;
static unsigned char pwm_count = 1;
static unsigned char soft_pwm_0;
static unsigned char soft_pwm_1;
static unsigned char soft_pwm_2;
if(pwm_count == 0){
soft_pwm_0 = soft_pwm[0];
if(soft_pwm_0 > 0) WRITE(HEATER_0_PIN,1);
#if EXTRUDERS > 1
soft_pwm_1 = soft_pwm[1];
if(soft_pwm_1 > 0) WRITE(HEATER_1_PIN,1);
#endif
#if EXTRUDERS > 2
soft_pwm_2 = soft_pwm[2];
if(soft_pwm_2 > 0) WRITE(HEATER_2_PIN,1);
#endif
}
if(soft_pwm_0 <= pwm_count) WRITE(HEATER_0_PIN,0);
#if EXTRUDERS > 1
if(soft_pwm_1 <= pwm_count) WRITE(HEATER_1_PIN,0);
#endif
#if EXTRUDERS > 2
if(soft_pwm_2 <= pwm_count) WRITE(HEATER_2_PIN,0);
#endif
pwm_count++;
pwm_count &= 0x7f;
switch(temp_state) { switch(temp_state) {
case 0: // Prepare TEMP_0 case 0: // Prepare TEMP_0
@ -505,7 +632,26 @@ ISR(TIMER0_COMPB_vect)
#endif #endif
temp_state = 2; temp_state = 2;
break; break;
case 2: // Prepare TEMP_1 case 2: // Prepare TEMP_BED
#if (TEMP_BED_PIN > -1)
#if TEMP_BED_PIN > 7
ADCSRB = 1<<MUX5;
#endif
ADMUX = ((1 << REFS0) | (TEMP_BED_PIN & 0x07));
ADCSRA |= 1<<ADSC; // Start conversion
#endif
#ifdef ULTIPANEL
buttons_check();
#endif
temp_state = 3;
break;
case 3: // Measure TEMP_BED
#if (TEMP_BED_PIN > -1)
raw_temp_bed_value += ADC;
#endif
temp_state = 4;
break;
case 4: // Prepare TEMP_1
#if (TEMP_1_PIN > -1) #if (TEMP_1_PIN > -1)
#if TEMP_1_PIN > 7 #if TEMP_1_PIN > 7
ADCSRB = 1<<MUX5; ADCSRB = 1<<MUX5;
@ -518,15 +664,15 @@ ISR(TIMER0_COMPB_vect)
#ifdef ULTIPANEL #ifdef ULTIPANEL
buttons_check(); buttons_check();
#endif #endif
temp_state = 3; temp_state = 5;
break; break;
case 3: // Measure TEMP_1 case 5: // Measure TEMP_1
#if (TEMP_1_PIN > -1) #if (TEMP_1_PIN > -1)
raw_temp_1_value += ADC; raw_temp_1_value += ADC;
#endif #endif
temp_state = 4; temp_state = 6;
break; break;
case 4: // Prepare TEMP_2 case 6: // Prepare TEMP_2
#if (TEMP_2_PIN > -1) #if (TEMP_2_PIN > -1)
#if TEMP_2_PIN > 7 #if TEMP_2_PIN > 7
ADCSRB = 1<<MUX5; ADCSRB = 1<<MUX5;
@ -539,39 +685,49 @@ ISR(TIMER0_COMPB_vect)
#ifdef ULTIPANEL #ifdef ULTIPANEL
buttons_check(); buttons_check();
#endif #endif
temp_state = 5; temp_state = 7;
break; break;
case 5: // Measure TEMP_2 case 7: // Measure TEMP_2
#if (TEMP_2_PIN > -1) #if (TEMP_2_PIN > -1)
raw_temp_2_value += ADC; raw_temp_2_value += ADC;
#endif #endif
temp_state = 0; temp_state = 0;
temp_count++; temp_count++;
break; break;
default: // default:
SERIAL_ERROR_START; // SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temp measurement error!"); // SERIAL_ERRORLNPGM("Temp measurement error!");
break; // break;
} }
if(temp_count >= 16) // 6 ms * 16 = 96ms. if(temp_count >= 16) // 8 ms * 16 = 128ms.
{ {
#ifdef HEATER_0_USES_AD595 #ifdef HEATER_0_USES_AD595
current_raw[0] = raw_temp_0_value; current_raw[0] = raw_temp_0_value;
#else #else
current_raw[0] = 16383 - raw_temp_0_value; current_raw[0] = 16383 - raw_temp_0_value;
#endif #endif
#if EXTRUDERS > 1
#ifdef HEATER_1_USES_AD595 #ifdef HEATER_1_USES_AD595
current_raw[1] = raw_temp_1_value;
#else
current_raw[1] = 16383 - raw_temp_1_value;
#endif
#endif
#if EXTRUDERS > 2
#ifdef HEATER_2_USES_AD595
current_raw[2] = raw_temp_2_value; current_raw[2] = raw_temp_2_value;
#else #else
current_raw[2] = 16383 - raw_temp_2_value; current_raw[2] = 16383 - raw_temp_2_value;
#endif #endif
#endif
#ifdef BED_USES_AD595 #ifdef BED_USES_AD595
current_raw[1] = raw_temp_1_value; current_raw_bed = raw_temp_bed_value;
#else #else
current_raw[1] = 16383 - raw_temp_1_value; current_raw_bed = 16383 - raw_temp_bed_value;
#endif #endif
temp_meas_ready = true; temp_meas_ready = true;
@ -579,77 +735,28 @@ ISR(TIMER0_COMPB_vect)
raw_temp_0_value = 0; raw_temp_0_value = 0;
raw_temp_1_value = 0; raw_temp_1_value = 0;
raw_temp_2_value = 0; raw_temp_2_value = 0;
#ifdef HEATER_0_MAXTEMP raw_temp_bed_value = 0;
#if (HEATER_0_PIN > -1)
if(current_raw[TEMPSENSOR_HOTEND_0] >= maxttemp_0) { for(unsigned char e = 0; e < EXTRUDERS; e++) {
target_raw[TEMPSENSOR_HOTEND_0] = 0; if(current_raw[e] >= maxttemp[e]) {
digitalWrite(HEATER_0_PIN, 0); target_raw[e] = 0;
SERIAL_ERROR_START; max_temp_error(e);
SERIAL_ERRORLNPGM("Temperature extruder 0 switched off. MAXTEMP triggered !!"); kill();;
}
if(current_raw[e] <= minttemp[e]) {
target_raw[e] = 0;
min_temp_error(e);
kill(); kill();
} }
#endif }
#endif
#ifdef HEATER_1_MAXTEMP
#if (HEATER_1_PIN > -1)
if(current_raw[TEMPSENSOR_HOTEND_1] >= maxttemp_1) {
target_raw[TEMPSENSOR_HOTEND_1] = 0;
digitalWrite(HEATER_2_PIN, 0);
SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temperature extruder 1 switched off. MAXTEMP triggered !!");
kill();
}
#endif
#endif //MAXTEMP
#ifdef HEATER_0_MINTEMP
#if (HEATER_0_PIN > -1)
if(current_raw[TEMPSENSOR_HOTEND_0] <= minttemp_0) {
target_raw[TEMPSENSOR_HOTEND_0] = 0;
digitalWrite(HEATER_0_PIN, 0);
SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temperature extruder 0 switched off. MINTEMP triggered !!");
kill();
}
#endif
#endif
#ifdef HEATER_1_MINTEMP
#if (HEATER_2_PIN > -1)
if(current_raw[TEMPSENSOR_HOTEND_1] <= minttemp_1) {
target_raw[TEMPSENSOR_HOTEND_1] = 0;
digitalWrite(HEATER_2_PIN, 0);
SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temperature extruder 1 switched off. MINTEMP triggered !!");
kill();
}
#endif
#endif //MAXTEMP
#ifdef BED_MINTEMP
#if (HEATER_1_PIN > -1)
if(current_raw[1] <= bed_minttemp) {
target_raw[1] = 0;
digitalWrite(HEATER_1_PIN, 0);
SERIAL_ERROR_START;
SERIAL_ERRORLNPGM("Temperatur heated bed switched off. MINTEMP triggered !!");
kill();
}
#endif
#endif
#ifdef BED_MAXTEMP #if defined(BED_MAXTEMP) && (HEATER_BED_PIN > -1)
#if (HEATER_1_PIN > -1) if(current_raw_bed >= bed_maxttemp) {
if(current_raw[1] >= bed_maxttemp) { target_raw_bed = 0;
target_raw[1] = 0; bed_max_temp_error();
digitalWrite(HEATER_1_PIN, 0); kill();
SERIAL_ERROR_START; }
SERIAL_ERRORLNPGM("Temperature heated bed switched off. MAXTEMP triggered !!"); #endif
kill();
}
#endif
#endif
} }
} }

118
Marlin/temperature.h
Unescape Escape View File

@ -32,95 +32,111 @@
void tp_init(); //initialise the heating void tp_init(); //initialise the heating
void manage_heater(); //it is critical that this is called periodically. void manage_heater(); //it is critical that this is called periodically.
enum TempSensor {TEMPSENSOR_HOTEND_0=0,TEMPSENSOR_BED=1, TEMPSENSOR_HOTEND_1=2};
//low leven conversion routines //low leven conversion routines
// do not use this routines and variables outsie of temperature.cpp // do not use this routines and variables outsie of temperature.cpp
int temp2analog(int celsius); int temp2analog(int celsius, uint8_t e);
int temp2analogBed(int celsius); int temp2analogBed(int celsius);
float analog2temp(int raw); float analog2temp(int raw, uint8_t e);
float analog2tempBed(int raw); float analog2tempBed(int raw);
extern int target_raw[3]; extern int target_raw[EXTRUDERS];
extern int heatingtarget_raw[3]; extern int heatingtarget_raw[EXTRUDERS];
extern int current_raw[3]; extern int current_raw[EXTRUDERS];
extern int target_raw_bed;
extern int current_raw_bed;
extern float Kp,Ki,Kd,Kc; extern float Kp,Ki,Kd,Kc;
#ifdef PIDTEMP #ifdef PIDTEMP
extern float pid_setpoint ; extern float pid_setpoint[EXTRUDERS];
#endif #endif
// #ifdef WATCHPERIOD // #ifdef WATCHPERIOD
// extern int watch_raw[3] ; extern int watch_raw[EXTRUDERS] ;
// extern unsigned long watchmillis; // extern unsigned long watchmillis;
// #endif // #endif
//high level conversion routines, for use outside of temperature.cpp //high level conversion routines, for use outside of temperature.cpp
//inline so that there is no performance decrease. //inline so that there is no performance decrease.
//deg=degreeCelsius //deg=degreeCelsius
FORCE_INLINE float degHotend0(){ return analog2temp(current_raw[TEMPSENSOR_HOTEND_0]);}; FORCE_INLINE float degHotend(uint8_t extruder) {
FORCE_INLINE float degHotend1(){ return analog2temp(current_raw[TEMPSENSOR_HOTEND_1]);}; return analog2temp(current_raw[extruder], extruder);
FORCE_INLINE float degBed() { return analog2tempBed(current_raw[TEMPSENSOR_BED]);};
FORCE_INLINE float degHotend(uint8_t extruder){
if(extruder == 0) return analog2temp(current_raw[TEMPSENSOR_HOTEND_0]);
if(extruder == 1) return analog2temp(current_raw[TEMPSENSOR_HOTEND_1]);
}; };
FORCE_INLINE float degTargetHotend0() { return analog2temp(target_raw[TEMPSENSOR_HOTEND_0]);}; FORCE_INLINE float degBed() {
FORCE_INLINE float degTargetHotend1() { return analog2temp(target_raw[TEMPSENSOR_HOTEND_1]);}; return analog2tempBed(current_raw_bed);
FORCE_INLINE float degTargetHotend(uint8_t extruder){
if(extruder == 0) return analog2temp(target_raw[TEMPSENSOR_HOTEND_0]);
if(extruder == 1) return analog2temp(target_raw[TEMPSENSOR_HOTEND_1]);
}; };
FORCE_INLINE float degTargetBed() { return analog2tempBed(target_raw[TEMPSENSOR_BED]);}; FORCE_INLINE float degTargetHotend(uint8_t extruder) {
return analog2temp(target_raw[extruder], extruder);
};
FORCE_INLINE void setTargetHotend0(const float &celsius) FORCE_INLINE float degTargetBed() {
{ return analog2tempBed(target_raw_bed);
target_raw[TEMPSENSOR_HOTEND_0]=temp2analog(celsius);
heatingtarget_raw[TEMPSENSOR_HOTEND_0]=temp2analog(celsius-HEATING_EARLY_FINISH_DEG_OFFSET);
#ifdef PIDTEMP
pid_setpoint = celsius;
#endif //PIDTEMP
}; };
FORCE_INLINE void setTargetHotend1(const float &celsius) { target_raw[TEMPSENSOR_HOTEND_1]=temp2analog(celsius);};
FORCE_INLINE void setTargetHotend(const float &celcius, uint8_t extruder){ FORCE_INLINE void setTargetHotend(const float &celsius, uint8_t extruder) {
if(extruder == 0) setTargetHotend0(celcius); target_raw[extruder] = temp2analog(celsius, extruder);
if(extruder == 1) setTargetHotend1(celcius); #ifdef PIDTEMP
pid_setpoint[extruder] = celsius;
#endif //PIDTEMP
};
FORCE_INLINE void setTargetBed(const float &celsius) {
target_raw_bed = temp2analogBed(celsius);
}; };
FORCE_INLINE void setTargetBed(const float &celsius) { target_raw[TEMPSENSOR_BED ]=temp2analogBed(celsius);};
FORCE_INLINE bool isHeatingHotend0() {return heatingtarget_raw[TEMPSENSOR_HOTEND_0] > current_raw[TEMPSENSOR_HOTEND_0];};
FORCE_INLINE bool isHeatingHotend1() {return target_raw[TEMPSENSOR_HOTEND_1] > current_raw[TEMPSENSOR_HOTEND_1];};
FORCE_INLINE bool isHeatingHotend(uint8_t extruder){ FORCE_INLINE bool isHeatingHotend(uint8_t extruder){
if(extruder == 0) return heatingtarget_raw[TEMPSENSOR_HOTEND_0] > current_raw[TEMPSENSOR_HOTEND_0]; return target_raw[extruder] > current_raw[extruder];
if(extruder == 1) return target_raw[TEMPSENSOR_HOTEND_1] > current_raw[TEMPSENSOR_HOTEND_1]; };
return false;
FORCE_INLINE bool isHeatingBed() {
return target_raw_bed > current_raw_bed;
}; };
FORCE_INLINE bool isHeatingBed() {return target_raw[TEMPSENSOR_BED] > current_raw[TEMPSENSOR_BED];};
FORCE_INLINE bool isCoolingHotend(uint8_t extruder) {
FORCE_INLINE bool isCoolingHotend0() {return target_raw[TEMPSENSOR_HOTEND_0] < current_raw[TEMPSENSOR_HOTEND_0];}; return target_raw[extruder] < current_raw[extruder];
FORCE_INLINE bool isCoolingHotend1() {return target_raw[TEMPSENSOR_HOTEND_1] < current_raw[TEMPSENSOR_HOTEND_1];};
FORCE_INLINE bool isCoolingHotend(uint8_t extruder){
if(extruder == 0) return target_raw[TEMPSENSOR_HOTEND_0] < current_raw[TEMPSENSOR_HOTEND_0];
if(extruder == 1) return target_raw[TEMPSENSOR_HOTEND_1] < current_raw[TEMPSENSOR_HOTEND_1];
return false;
}; };
FORCE_INLINE bool isCoolingBed() {return target_raw[TEMPSENSOR_BED] < current_raw[TEMPSENSOR_BED];};
FORCE_INLINE bool isCoolingBed() {
return target_raw_bed < current_raw_bed;
};
#define degHotend0() degHotend(0)
#define degTargetHotend0() degTargetHotend(0)
#define setTargetHotend0(_celsius) setTargetHotend((_celsius), 0)
#define isHeatingHotend0() isHeatingHotend(0)
#define isCoolingHotend0() isCoolingHotend(0)
#if EXTRUDERS > 1
#define degHotend1() degHotend(1)
#define degTargetHotend1() degTargetHotend(1)
#define setTargetHotend1(_celsius) setTargetHotend((_celsius), 1)
#define isHeatingHotend1() isHeatingHotend(1)
#define isCoolingHotend1() isCoolingHotend(1)
#endif
#if EXTRUDERS > 2
#define degHotend2() degHotend(2)
#define degTargetHotend2() degTargetHotend(2)
#define setTargetHotend2(_celsius) setTargetHotend((_celsius), 2)
#define isHeatingHotend2() isHeatingHotend(2)
#define isCoolingHotend2() isCoolingHotend(2)
#endif
#if EXTRUDERS > 3
#error Invalid number of extruders
#endif
FORCE_INLINE void autotempShutdown(){ FORCE_INLINE void autotempShutdown(){
#ifdef AUTOTEMP #ifdef AUTOTEMP
if(autotemp_enabled) if(autotemp_enabled)
{ {
autotemp_enabled=false; autotemp_enabled=false;
if(degTargetHotend0()>autotemp_min) if(degTargetHotend(ACTIVE_EXTRUDER)>autotemp_min)
setTargetHotend0(0); setTargetHotend(0,ACTIVE_EXTRUDER);
} }
#endif #endif
} }
int getHeaterPower(int heater);
void disable_heater(); void disable_heater();
void setWatch(); void setWatch();
void updatePID(); void updatePID();

147
Marlin/thermistortables.h
Unescape Escape View File

@ -5,10 +5,9 @@
#define OVERSAMPLENR 16 #define OVERSAMPLENR 16
#if (THERMISTORHEATER_0 == 1) || (THERMISTORHEATER_1 == 1) || (THERMISTORBED == 1) //100k bed thermistor #if (THERMISTORHEATER_0 == 1) || (THERMISTORHEATER_1 == 1) || (THERMISTORHEATER_2 == 1) || (THERMISTORBED == 1) //100k bed thermistor
#define NUMTEMPS_1 61 const short temptable_1[][2] PROGMEM = {
const short temptable_1[NUMTEMPS_1][2] PROGMEM = {
{ 23*OVERSAMPLENR , 300 }, { 23*OVERSAMPLENR , 300 },
{ 25*OVERSAMPLENR , 295 }, { 25*OVERSAMPLENR , 295 },
{ 27*OVERSAMPLENR , 290 }, { 27*OVERSAMPLENR , 290 },
@ -72,9 +71,8 @@ const short temptable_1[NUMTEMPS_1][2] PROGMEM = {
{ 1008*OVERSAMPLENR , 0 } //safety { 1008*OVERSAMPLENR , 0 } //safety
}; };
#endif #endif
#if (THERMISTORHEATER_0 == 2) || (THERMISTORHEATER_1 == 2) || (THERMISTORBED == 2) //200k bed thermistor #if (THERMISTORHEATER_0 == 2) || (THERMISTORHEATER_1 == 2) || (THERMISTORHEATER_2 == 2) || (THERMISTORBED == 2) //200k bed thermistor
#define NUMTEMPS_2 21 const short temptable_2[][2] PROGMEM = {
const short temptable_2[NUMTEMPS_2][2] PROGMEM = {
{1*OVERSAMPLENR, 848}, {1*OVERSAMPLENR, 848},
{54*OVERSAMPLENR, 275}, {54*OVERSAMPLENR, 275},
{107*OVERSAMPLENR, 228}, {107*OVERSAMPLENR, 228},
@ -99,9 +97,8 @@ const short temptable_2[NUMTEMPS_2][2] PROGMEM = {
}; };
#endif #endif
#if (THERMISTORHEATER_0 == 3) || (THERMISTORHEATER_1 == 3) || (THERMISTORBED == 3) //mendel-parts #if (THERMISTORHEATER_0 == 3) || (THERMISTORHEATER_1 == 3) || (THERMISTORHEATER_2 == 3) || (THERMISTORBED == 3) //mendel-parts
#define NUMTEMPS_3 28 const short temptable_3[][2] PROGMEM = {
const short temptable_3[NUMTEMPS_3][2] PROGMEM = {
{1*OVERSAMPLENR,864}, {1*OVERSAMPLENR,864},
{21*OVERSAMPLENR,300}, {21*OVERSAMPLENR,300},
{25*OVERSAMPLENR,290}, {25*OVERSAMPLENR,290},
@ -133,10 +130,8 @@ const short temptable_3[NUMTEMPS_3][2] PROGMEM = {
}; };
#endif #endif
#if (THERMISTORHEATER_0 == 4) || (THERMISTORHEATER_1 == 4) || (THERMISTORBED == 4) //10k thermistor #if (THERMISTORHEATER_0 == 4) || (THERMISTORHEATER_1 == 4) || (THERMISTORHEATER_2 == 4) || (THERMISTORBED == 4) //10k thermistor
const short temptable_4[][2] PROGMEM = {
#define NUMTEMPS_4 20
const short temptable_4[NUMTEMPS_4][2] PROGMEM = {
{1*OVERSAMPLENR, 430}, {1*OVERSAMPLENR, 430},
{54*OVERSAMPLENR, 137}, {54*OVERSAMPLENR, 137},
{107*OVERSAMPLENR, 107}, {107*OVERSAMPLENR, 107},
@ -160,10 +155,8 @@ const short temptable_4[NUMTEMPS_4][2] PROGMEM = {
}; };
#endif #endif
#if (THERMISTORHEATER_0 == 5) || (THERMISTORHEATER_1 == 5) || (THERMISTORBED == 5) //100k ParCan thermistor (104GT-2) #if (THERMISTORHEATER_0 == 5) || (THERMISTORHEATER_1 == 5) || (THERMISTORHEATER_2 == 5) || (THERMISTORBED == 5) //100k ParCan thermistor (104GT-2)
const short temptable_5[][2] PROGMEM = {
#define NUMTEMPS_5 61
const short temptable_5[NUMTEMPS_5][2] PROGMEM = {
{1*OVERSAMPLENR, 713}, {1*OVERSAMPLENR, 713},
{18*OVERSAMPLENR, 316}, {18*OVERSAMPLENR, 316},
{35*OVERSAMPLENR, 266}, {35*OVERSAMPLENR, 266},
@ -228,9 +221,8 @@ const short temptable_5[NUMTEMPS_5][2] PROGMEM = {
}; };
#endif #endif
#if (THERMISTORHEATER_0 == 6) || (THERMISTORHEATER_1 == 6) || (THERMISTORBED == 6) // 100k Epcos thermistor #if (THERMISTORHEATER_0 == 6) || (THERMISTORHEATER_1 == 6) || (THERMISTORHEATER_2 == 6) || (THERMISTORBED == 6) // 100k Epcos thermistor
#define NUMTEMPS_6 36 const short temptable_6[][2] PROGMEM = {
const short temptable_6[NUMTEMPS_6][2] PROGMEM = {
{28*OVERSAMPLENR, 250}, {28*OVERSAMPLENR, 250},
{31*OVERSAMPLENR, 245}, {31*OVERSAMPLENR, 245},
{35*OVERSAMPLENR, 240}, {35*OVERSAMPLENR, 240},
@ -270,9 +262,8 @@ const short temptable_6[NUMTEMPS_6][2] PROGMEM = {
}; };
#endif #endif
#if (THERMISTORHEATER_0 == 7) || (THERMISTORHEATER_1 == 7) || (THERMISTORBED == 7) // 100k Honeywell 135-104LAG-J01 #if (THERMISTORHEATER_0 == 7) || (THERMISTORHEATER_1 == 7) || (THERMISTORHEATER_2 == 7) || (THERMISTORBED == 7) // 100k Honeywell 135-104LAG-J01
#define NUMTEMPS_7 54 const short temptable_7[][2] PROGMEM = {
const short temptable_7[NUMTEMPS_7][2] PROGMEM = {
{46*OVERSAMPLENR, 270}, {46*OVERSAMPLENR, 270},
{50*OVERSAMPLENR, 265}, {50*OVERSAMPLENR, 265},
{54*OVERSAMPLENR, 260}, {54*OVERSAMPLENR, 260},
@ -330,82 +321,52 @@ const short temptable_7[NUMTEMPS_7][2] PROGMEM = {
}; };
#endif #endif
#define _TT_NAME(_N) temptable_ ## _N
#define TT_NAME(_N) _TT_NAME(_N)
#ifdef THERMISTORHEATER_0
#if THERMISTORHEATER_0 == 1 #define heater_0_temptable TT_NAME(THERMISTORHEATER_0)
#define NUMTEMPS_HEATER_0 NUMTEMPS_1 #define heater_0_temptable_len (sizeof(heater_0_temptable)/sizeof(*heater_0_temptable))
#define heater_0_temptable temptable_1 #else
#elif THERMISTORHEATER_0 == 2 #ifdef HEATER_0_USES_THERMISTOR
#define NUMTEMPS_HEATER_0 NUMTEMPS_2 #error No heater 0 thermistor table specified
#define heater_0_temptable temptable_2 #else // HEATER_0_USES_THERMISTOR
#elif THERMISTORHEATER_0 == 3 #define heater_0_temptable 0
#define NUMTEMPS_HEATER_0 NUMTEMPS_3 #define heater_0_temptable_len 0
#define heater_0_temptable temptable_3 #endif // HEATER_0_USES_THERMISTOR
#elif THERMISTORHEATER_0 == 4
#define NUMTEMPS_HEATER_0 NUMTEMPS_4
#define heater_0_temptable temptable_4
#elif THERMISTORHEATER_0 == 5
#define NUMTEMPS_HEATER_0 NUMTEMPS_5
#define heater_0_temptable temptable_5
#elif THERMISTORHEATER_0 == 6
#define NUMTEMPS_HEATER_0 NUMTEMPS_6
#define heater_0_temptable temptable_6
#elif THERMISTORHEATER_0 == 7
#define NUMTEMPS_HEATER_0 NUMTEMPS_7
#define heater_0_temptable temptable_7
#elif defined HEATER_0_USES_THERMISTOR
#error No heater 0 thermistor table specified
#endif #endif
#if THERMISTORHEATER_1 == 1 #ifdef THERMISTORHEATER_1
#define NUMTEMPS_HEATER_1 NUMTEMPS_1 #define heater_1_temptable TT_NAME(THERMISTORHEATER_1)
#define heater_1_temptable temptable_1 #define heater_1_temptable_len (sizeof(heater_1_temptable)/sizeof(*heater_1_temptable))
#elif THERMISTORHEATER_1 == 2 #else
#define NUMTEMPS_HEATER_1 NUMTEMPS_2 #ifdef HEATER_1_USES_THERMISTOR
#define heater_1_temptable temptable_2 #error No heater 1 thermistor table specified
#elif THERMISTORHEATER_1 == 3 #else // HEATER_1_USES_THERMISTOR
#define NUMTEMPS_HEATER_1 NUMTEMPS_3 #define heater_1_temptable 0
#define heater_1_temptable temptable_3 #define heater_1_temptable_len 0
#elif THERMISTORHEATER_1 == 4 #endif // HEATER_1_USES_THERMISTOR
#define NUMTEMPS_HEATER_1 NUMTEMPS_4
#define heater_1_temptable temptable_4
#elif THERMISTORHEATER_1 == 5
#define NUMTEMPS_HEATER_1 NUMTEMPS_5
#define heater_1_temptable temptable_5
#elif THERMISTORHEATER_1 == 6
#define NUMTEMPS_HEATER_1 NUMTEMPS_6
#define heater_1_temptable temptable_6
#elif THERMISTORHEATER_1 == 7
#define NUMTEMPS_HEATER_1 NUMTEMPS_7
#define heater_1_temptable temptable_7
#elif defined HEATER_1_USES_THERMISTOR
#error No heater 1 thermistor table specified
#endif #endif
#ifdef THERMISTORHEATER_2
#define heater_2_temptable TT_NAME(THERMISTORHEATER_2)
#define heater_2_temptable_len (sizeof(heater_2_temptable)/sizeof(*heater_2_temptable))
#else
#ifdef HEATER_2_USES_THERMISTOR
#error No heater 2 thermistor table specified
#else // HEATER_2_USES_THERMISTOR
#define heater_2_temptable 0
#define heater_2_temptable_len 0
#endif // HEATER_2_USES_THERMISTOR
#endif
#if THERMISTORBED == 1 #ifdef THERMISTORBED
#define BNUMTEMPS NUMTEMPS_1 #define bedtemptable TT_NAME(THERMISTORBED)
#define bedtemptable temptable_1 #define bedtemptable_len (sizeof(bedtemptable)/sizeof(*bedtemptable))
#elif THERMISTORBED == 2 #else
#define BNUMTEMPS NUMTEMPS_2 #ifdef BED_USES_THERMISTOR
#define bedtemptable temptable_2 #error No bed thermistor table specified
#elif THERMISTORBED == 3 #endif // BED_USES_THERMISTOR
#define BNUMTEMPS NUMTEMPS_3
#define bedtemptable temptable_3
#elif THERMISTORBED == 4
#define BNUMTEMPS NUMTEMPS_4
#define bedtemptable temptable_4
#elif THERMISTORBED == 5
#define BNUMTEMPS NUMTEMPS_5
#define bedtemptable temptable_5
#elif THERMISTORBED == 6
#define BNUMTEMPS NUMTEMPS_6
#define bedtemptable temptable_6
#elif THERMISTORBED == 7
#define BNUMTEMPS NUMTEMPS_7
#define bedtemptable temptable_7
#elif defined BED_USES_THERMISTOR
#error No bed thermistor table specified
#endif #endif
#endif //THERMISTORTABLES_H_ #endif //THERMISTORTABLES_H_

3692
Marlin/ultralcd.pde
View File

File diff suppressed because it is too large Load Diff
Write Preview
Loading…
Cancel
Save