Touch-MI Menu and Manual Deploy option (#14290)

Marlin/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

Marlin/src/lcd/language/language_en.h

@@ -948,6 +948,21 @@
 #ifndef MSG_BLTOUCH_MODE_CHANGE
   #define MSG_BLTOUCH_MODE_CHANGE             _UxGT("DANGER: Bad settings can cause damage! Proceed anyway?")
 #endif
+#ifndef MSG_TOUCHMI_PROBE
+  #define MSG_TOUCHMI_PROBE                   _UxGT("TouchMI")
+#endif
+#ifndef MSG_TOUCHMI_INIT
+  #define MSG_TOUCHMI_INIT                    _UxGT("Init TouchMI")
+#endif
+#ifndef MSG_TOUCHMI_ZTEST
+  #define MSG_TOUCHMI_ZTEST                   _UxGT("Z offset Test")
+#endif
+#ifndef MSG_TOUCHMI_SAVE
+ #define MSG_TOUCHMI_SAVE                     _UxGT("Save")
+#endif
+#ifndef MSG_MANUAL_DEPLOY_TOUCHMI
+  #define MSG_MANUAL_DEPLOY_TOUCHMI           _UxGT("Deploy TouchMI")
+#endif
 #ifndef MSG_MANUAL_DEPLOY
   #define MSG_MANUAL_DEPLOY                   _UxGT("Deploy Z-Probe")
 #endif

Marlin/src/lcd/language/language_fr.h

@@ -334,6 +334,11 @@
 #define MSG_BLTOUCH_MODE_STORE_5V           _UxGT("Mise en 5V")
 #define MSG_BLTOUCH_MODE_STORE_OD           _UxGT("Mise en OD")
 #define MSG_BLTOUCH_MODE_ECHO               _UxGT("Afficher Mode")
+#define MSG_TOUCHMI_PROBE                   _UxGT("TouchMI")
+#define MSG_TOUCHMI_INIT                    _UxGT("Init. TouchMI")
+#define MSG_TOUCHMI_ZTEST                   _UxGT("Test décalage Z")
+#define MSG_TOUCHMI_SAVE                    _UxGT("Sauvegarde")
+#define MSG_MANUAL_DEPLOY_TOUCHMI           _UxGT("Déployer TouchMI")
 #define MSG_MANUAL_DEPLOY                   _UxGT("Déployer Sonde Z")
 #define MSG_MANUAL_STOW                     _UxGT("Ranger Sonde Z")
 #define MSG_HOME                            _UxGT("Origine")  // Used as MSG_HOME " " MSG_X MSG_Y MSG_Z " " MSG_FIRST

Marlin/src/lcd/menu/menu_configuration.cpp

@@ -219,6 +219,19 @@ static void lcd_factory_settings() {
 
 #endif
 
+#if ENABLED(TOUCH_MI_PROBE)
+  void menu_touchmi() {
+    START_MENU();
+    ui.defer_status_screen();
+    MENU_BACK(MSG_CONFIGURATION);
+    MENU_ITEM(gcode, MSG_TOUCHMI_INIT, PSTR("M851 Z0\nG28\nG1 F200 Z0"));
+    MENU_ITEM(submenu, MSG_ZPROBE_ZOFFSET, lcd_babystep_zoffset);
+    MENU_ITEM(gcode, MSG_TOUCHMI_SAVE, PSTR("M500\nG1 F200 Z10"));
+    MENU_ITEM(gcode, MSG_TOUCHMI_ZTEST, PSTR("G28\nG1 F200 Z0"));
+    END_MENU();
+  }
+#endif
+
 #if ENABLED(CASE_LIGHT_MENU)
 
   #include "../../feature/caselight.h"
@@ -347,6 +360,10 @@ void menu_configuration() {
     #if ENABLED(BLTOUCH)
       MENU_ITEM(submenu, MSG_BLTOUCH, menu_bltouch);
     #endif
+
+    #if ENABLED(TOUCH_MI_PROBE)
+      MENU_ITEM(submenu, MSG_TOUCHMI_PROBE, menu_touchmi);
+    #endif
   }
 
   //

Marlin/src/module/probe.cpp

@@ -109,10 +109,26 @@ float zprobe_zoffset; // Initialized by settings.load()
   void run_deploy_moves_script() {
     #ifndef TOUCH_MI_DEPLOY_XPOS
       #define TOUCH_MI_DEPLOY_XPOS 0
-    #elif X_HOME_DIR > 0 && TOUCH_MI_DEPLOY_XPOS > X_MAX_BED
+    #elif TOUCH_MI_DEPLOY_XPOS > X_MAX_BED
       TemporaryGlobalEndstopsState unlock_x(false);
     #endif
-    do_blocking_move_to_x(TOUCH_MI_DEPLOY_XPOS);
+
+    #if ENABLED(TOUCH_MI_MANUAL_DEPLOY)
+      const screenFunc_t prev_screen = ui.currentScreen;
+      LCD_MESSAGEPGM(MSG_MANUAL_DEPLOY_TOUCHMI);
+      ui.return_to_status();
+
+      KEEPALIVE_STATE(PAUSED_FOR_USER);
+      wait_for_user = true; // LCD click or M108 will clear this
+      #if ENABLED(HOST_PROMPT_SUPPORT)
+        host_prompt_do(PROMPT_USER_CONTINUE, PSTR("Deploy TouchMI probe."), PSTR("Continue"));
+      #endif
+      while (wait_for_user) idle();
+      ui.reset_status();
+      ui.goto_screen(prev_screen);
+    #else
+      do_blocking_move_to_x(TOUCH_MI_DEPLOY_XPOS);
+    #endif
   }
 
   // Move down to the bed to stow the probe

config/default/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/3DFabXYZ/Migbot/Configuration.h

@@ -845,12 +845,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/AlephObjects/TAZ4/Configuration.h

@@ -859,12 +859,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/AliExpress/CL-260/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/AliExpress/UM2pExt/Configuration.h

@@ -850,12 +850,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Anet/A2/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Anet/A2plus/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Anet/A6/Configuration.h

@@ -886,12 +886,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Anet/A8/Configuration.h

@@ -852,12 +852,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Anet/A8plus/Configuration.h

@@ -850,12 +850,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Anet/E16/Configuration.h

@@ -851,12 +851,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/AnyCubic/i3/Configuration.h

@@ -849,12 +849,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/ArmEd/Configuration.h

@@ -840,12 +840,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Azteeg/X5GT/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/BIBO/TouchX/cyclops/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/BIBO/TouchX/default/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/BQ/Hephestos/Configuration.h

@@ -827,12 +827,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/BQ/Hephestos_2/Configuration.h

@@ -840,12 +840,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/BQ/WITBOX/Configuration.h

@@ -827,12 +827,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Cartesio/Configuration.h

@@ -838,12 +838,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Creality/CR-10/Configuration.h

@@ -849,12 +849,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Creality/CR-10S/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Creality/CR-10_5S/Configuration.h

@@ -840,12 +840,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Creality/CR-10mini/Configuration.h

@@ -858,12 +858,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Creality/CR-8/Configuration.h

@@ -849,12 +849,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Creality/Ender-2/Configuration.h

@@ -843,12 +843,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Creality/Ender-3/Configuration.h

@@ -843,12 +843,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Creality/Ender-4/Configuration.h

@@ -849,12 +849,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Dagoma/Disco Ultimate/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h

@@ -844,12 +844,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Einstart-S/Configuration.h

@@ -849,12 +849,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Felix/Configuration.h

@@ -821,12 +821,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Felix/DUAL/Configuration.h

@@ -821,12 +821,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/FlashForge/CreatorPro/Configuration.h

@@ -831,12 +831,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/FolgerTech/i3-2020/Configuration.h

@@ -845,12 +845,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Formbot/Raptor/Configuration.h

@@ -922,12 +922,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Formbot/T_Rex_2+/Configuration.h

@@ -868,12 +868,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Formbot/T_Rex_3/Configuration.h

@@ -855,12 +855,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Fysetc/AIO_II/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Fysetc/CHEETAH/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Fysetc/F6_13/Configuration.h

@@ -841,12 +841,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Geeetech/A10/Configuration.h

@@ -822,12 +822,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Geeetech/A10M/Configuration.h

@@ -822,12 +822,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Geeetech/A20M/Configuration.h

@@ -822,12 +822,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Geeetech/GT2560/Configuration.h

@@ -854,12 +854,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Geeetech/MeCreator2/Configuration.h

@@ -846,12 +846,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -860,12 +860,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -859,12 +859,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Geeetech/Prusa i3 Pro C/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Geeetech/Prusa i3 Pro W/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Infitary/i3-M508/Configuration.h

@@ -843,12 +843,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/JGAurora/A1/Configuration.h

@@ -841,12 +841,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/JGAurora/A5/Configuration.h

@@ -851,12 +851,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/JGAurora/A5S/Configuration.h

@@ -841,12 +841,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/MakerParts/Configuration.h

@@ -859,12 +859,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Malyan/M150/Configuration.h

@@ -859,12 +859,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Malyan/M200/Configuration.h

@@ -838,12 +838,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Micromake/C1/basic/Configuration.h

@@ -843,12 +843,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Micromake/C1/enhanced/Configuration.h

@@ -843,12 +843,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Mks/Robin/Configuration.h

@@ -840,12 +840,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Mks/Sbase/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Printrbot/PrintrboardG2/Configuration.h

@@ -847,12 +847,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/RapideLite/RL200/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/RepRapPro/Huxley/Configuration.h

@@ -879,12 +879,13 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/RepRapWorld/Megatronics/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/RigidBot/Configuration.h

@@ -837,12 +837,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/SCARA/Configuration.h

@@ -852,12 +852,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/STM32/Black_STM32F407VET6/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/STM32/STM32F10/Configuration.h

@@ -841,12 +841,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/STM32/STM32F4/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/STM32/stm32f103ret6/Configuration.h

@@ -841,12 +841,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Sanguinololu/Configuration.h

@@ -870,12 +870,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Tevo/Tarantula Pro/Configuration.h

@@ -844,12 +844,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/TheBorg/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/TinyBoy2/Configuration.h

@@ -890,12 +890,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Tronxy/X1/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Tronxy/X3A/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Tronxy/X5S-2E/Configuration.h

@@ -860,12 +860,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Tronxy/X5S/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Tronxy/XY100/Configuration.h

@@ -850,12 +850,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/UltiMachine/Archim1/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/UltiMachine/Archim2/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/VORONDesign/Configuration.h

@@ -848,12 +848,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Velleman/K8200/Configuration.h

@@ -868,12 +868,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Velleman/K8400/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Velleman/K8400/Dual-head/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/WASP/PowerWASP/Configuration.h

@@ -858,12 +858,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/Wanhao/Duplicator 6/Configuration.h

@@ -849,12 +849,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/adafruit/ST7565/Configuration.h

@@ -839,12 +839,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/delta/Anycubic/Kossel/Configuration.h

@@ -975,12 +975,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/delta/FLSUN/auto_calibrate/Configuration.h

@@ -921,12 +921,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/delta/FLSUN/kossel/Configuration.h

@@ -921,12 +921,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/delta/FLSUN/kossel_mini/Configuration.h

@@ -921,12 +921,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)

config/examples/delta/Geeetech/Rostock 301/Configuration.h

@@ -911,12 +911,13 @@
  * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position.
  *
  * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING,
- *                MIN_PROBE_EDGE, and a minimum Z_HOMING_HEIGHT of 10.
+ *                and a minimum Z_HOMING_HEIGHT of 10.
  */
 //#define TOUCH_MI_PROBE
 #if ENABLED(TOUCH_MI_PROBE)
   #define TOUCH_MI_RETRACT_Z 0.5                  // Height at which the probe retracts
   //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2)  // For a magnet on the right side of the bed
+  //#define TOUCH_MI_MANUAL_DEPLOY                // For manual deploy (LCD menu)
 #endif
 
 // A probe that is deployed and stowed with a solenoid pin (SOL1_PIN)