Add a minimum Z change option to power-loss recovery (#13859)

Marlin/Configuration_adv.h

@@ -803,6 +803,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

Marlin/src/feature/power_loss_recovery.cpp

@@ -126,6 +126,10 @@ void PrintJobRecovery::save(const bool force/*=false*/, const bool save_queue/*=
     millis_t ms = millis();
   #endif
 
+  #ifndef POWER_LOSS_MIN_Z_CHANGE
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05  // Vase-mode-friendly out of the box
+  #endif
+
   // Did Z change since the last call?
   if (force
     #if DISABLED(SAVE_EACH_CMD_MODE)      // Always save state when enabled
@@ -135,8 +139,8 @@ void PrintJobRecovery::save(const bool force/*=false*/, const bool save_queue/*=
       #if SAVE_INFO_INTERVAL_MS > 0       // Save if interval is elapsed
         || ELAPSED(ms, next_save_ms)
       #endif
-        // Save every time Z is higher than the last call
-        || current_position[Z_AXIS] > info.current_position[Z_AXIS]
+      // Save if Z is above the last-saved position by some minimum height
+      || current_position[Z_AXIS] > info.current_position[Z_AXIS] + POWER_LOSS_MIN_Z_CHANGE
     #endif
   ) {
 
@@ -228,9 +232,8 @@ void PrintJobRecovery::write() {
   open(false);
   file.seekSet(0);
   const int16_t ret = file.write(&info, sizeof(info));
-  close();
-
   if (ret == -1) DEBUG_ECHOLNPGM("Power-loss file write failed.");
+  if (!file.close()) DEBUG_ECHOLNPGM("Power-loss file close failed.");
 }
 
 /**

config/default/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/AlephObjects/TAZ4/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/AliExpress/UM2pExt/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Anet/A2/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Anet/A2plus/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Anet/A6/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Anet/A8/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/AnyCubic/i3/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/ArmEd/Configuration_adv.h

@@ -809,6 +809,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/BIBO/TouchX/cyclops/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/BIBO/TouchX/default/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/BQ/Hephestos/Configuration_adv.h

@@ -802,6 +802,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/BQ/Hephestos_2/Configuration_adv.h

@@ -810,6 +810,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/BQ/WITBOX/Configuration_adv.h

@@ -802,6 +802,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Cartesio/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Creality/CR-10/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Creality/CR-10S/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Creality/CR-10_5S/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Creality/CR-10mini/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Creality/CR-8/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Creality/Ender-2/Configuration_adv.h

@@ -802,6 +802,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Creality/Ender-3/Configuration_adv.h

@@ -802,6 +802,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Creality/Ender-4/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Einstart-S/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Felix/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/FlashForge/CreatorPro/Configuration_adv.h

@@ -801,6 +801,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/FolgerTech/i3-2020/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Formbot/Raptor/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Formbot/T_Rex_2+/Configuration_adv.h

@@ -809,6 +809,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Formbot/T_Rex_3/Configuration_adv.h

@@ -809,6 +809,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Geeetech/MeCreator2/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Infitary/i3-M508/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/JGAurora/A5/Configuration_adv.h

@@ -802,6 +802,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/MakerParts/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Malyan/M150/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Malyan/M200/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Micromake/C1/enhanced/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Mks/Robin/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Mks/Sbase/Configuration_adv.h

@@ -806,6 +806,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/RapideLite/RL200/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/RigidBot/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/SCARA/Configuration_adv.h

@@ -802,6 +802,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h

@@ -802,6 +802,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Sanguinololu/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/TheBorg/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/TinyBoy2/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Tronxy/X3A/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Tronxy/X5S-2E/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/UltiMachine/Archim1/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/UltiMachine/Archim2/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/VORONDesign/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Velleman/K8200/Configuration_adv.h

@@ -818,6 +818,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Velleman/K8400/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/Wanhao/Duplicator 6/Configuration_adv.h

@@ -804,6 +804,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/delta/Anycubic/Kossel/Configuration_adv.h

@@ -804,6 +804,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h

@@ -804,6 +804,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/delta/FLSUN/kossel/Configuration_adv.h

@@ -804,6 +804,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h

@@ -804,6 +804,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h

@@ -804,6 +804,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/delta/MKS/SBASE/Configuration_adv.h

@@ -804,6 +804,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/delta/Tevo Little Monster/Configuration_adv.h

@@ -804,6 +804,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/delta/generic/Configuration_adv.h

@@ -804,6 +804,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/delta/kossel_mini/Configuration_adv.h

@@ -803,6 +803,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/delta/kossel_xl/Configuration_adv.h

@@ -804,6 +804,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/gCreate/gMax1.5+/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/makibox/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/tvrrug/Round2/Configuration_adv.h

@@ -805,6 +805,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**

config/examples/wt150/Configuration_adv.h

@@ -806,6 +806,10 @@
   #if ENABLED(POWER_LOSS_RECOVERY)
     //#define POWER_LOSS_PIN   44     // Pin to detect power loss
     //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
+
+    // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
+    // especially with "vase mode" printing. Set too high and vases cannot be continued.
+    #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
   #endif
 
   /**