You cannot select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

151 lines
4.3 KiB
C

/**
* Marlin 3D Printer Firmware
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Open Motion controller with enable based extruders (Final!)
*
* ATmega644
*
* +---\/---+
* (D 0) PB0 1| |40 PA0 (AI 0 / D31)
* (D 1) PB1 2| |39 PA1 (AI 1 / D30)
* INT2 (D 2) PB2 3| |38 PA2 (AI 2 / D29)
* PWM (D 3) PB3 4| |37 PA3 (AI 3 / D28)
* PWM (D 4) PB4 5| |36 PA4 (AI 4 / D27)
* MOSI (D 5) PB5 6| |35 PA5 (AI 5 / D26)
* MISO (D 6) PB6 7| |34 PA6 (AI 6 / D25)
* SCK (D 7) PB7 8| |33 PA7 (AI 7 / D24)
* RST 9| |32 AREF
* VCC 10| |31 GND
* GND 11| |30 AVCC
* XTAL2 12| |29 PC7 (D 23)
* XTAL1 13| |28 PC6 (D 22)
* RX0 (D 8) PD0 14| |27 PC5 (D 21) TDI
* TX0 (D 9) PD1 15| |26 PC4 (D 20) TDO
* INT0 RX1 (D 10) PD2 16| |25 PC3 (D 19) TMS
* INT1 TX1 (D 11) PD3 17| |24 PC2 (D 18) TCK
* PWM (D 12) PD4 18| |23 PC1 (D 17) SDA
* PWM (D 13) PD5 19| |22 PC0 (D 16) SCL
* PWM (D 14) PD6 20| |21 PD7 (D 15) PWM
* +--------+
*
* REF http://sanguino.cc/hardware
*/
/**
* Rev B 26 DEC 2016
*
* added pointer to a current Arduino IDE extension
*
*/
/**
* A useable Arduino IDE extension (board manager) can be found at
* https://github.com/Lauszus/Sanguino
*
* This extension has been tested on Arduino 1.6.12 & 1.8.0
*
* Here's the JSON path:
* https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json
*
* When installing select 1.0.2
*
* Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino
* Just use the above JSON URL instead of Sparkfun's JSON.
*
* Once installed select the Sanguino board and then select the CPU.
*
*/
#if !defined(__AVR_ATmega644P__) && !defined(__AVR_ATmega644__)
#error "Oops! Select 'Sanguino' in 'Tools > Board' and 'ATmega644' or 'ATmega644P' in 'Tools > Processor.'"
#endif
#define BOARD_NAME "Final OMCA"
//
// Limit Switches
//
#define X_STOP_PIN 0
#define Y_STOP_PIN 1
#define Z_STOP_PIN 2
//
// Steppers
//
#define X_STEP_PIN 26
#define X_DIR_PIN 25
#define X_ENABLE_PIN 10
#define Y_STEP_PIN 28
#define Y_DIR_PIN 27
#define Y_ENABLE_PIN 10
#define Z_STEP_PIN 23
#define Z_DIR_PIN 22
#define Z_ENABLE_PIN 10
#define E0_STEP_PIN 24
#define E0_DIR_PIN 21
#define E0_ENABLE_PIN 10
#define E1_STEP_PIN -1 // 21
#define E1_DIR_PIN -1 // 20
#define E1_ENABLE_PIN -1 // 19
#define E2_STEP_PIN -1 // 21
#define E2_DIR_PIN -1 // 20
#define E2_ENABLE_PIN -1 // 18
//
// Temperature Sensors
//
#define TEMP_0_PIN 0 // Analog Input
#define TEMP_1_PIN 1 // Analog Input
#define TEMP_BED_PIN 2 // Analog Input (1,2 or I2C)
//
// Heaters / Fans
//
#define HEATER_0_PIN 3 // DONE PWM on RIGHT connector
#define HEATER_BED_PIN 4
#ifndef FAN_PIN
#define FAN_PIN 14 // PWM on MIDDLE connector
#endif
//
// Misc. Functions
//
#define SDSS 11
#define I2C_SCL_PIN 16
#define I2C_SDA_PIN 17
// future proofing
#define __FS 20
#define __FD 19
#define __GS 18
#define __GD 13
#define UNUSED_PWM 14 // PWM on LEFT connector