You cannot select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

249 lines
6.2 KiB
C

/**
* Marlin 3D Printer Firmware
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
//
// Fysetc F6 pin assignments
//
#ifndef __AVR_ATmega2560__
#error "Oops! Select 'FYSETC F6' in 'Tools > Board.'"
#endif
#if ENABLED(SD_DETECT_INVERTED)
//#error "SD_DETECT_INVERTED must be disabled for the FYSETC_F6_13 board."
#endif
#define BOARD_NAME "FYSETC F6 1.3"
#define RESET_PIN 30
#define SPI_FLASH_CS 83
//
// Servos
//
#define SERVO0_PIN 13
#define SERVO1_PIN 11 // (PS_ON_PIN)
#define SERVO2_PIN 10 // (FIL_RUNOUT_PIN)
#define SERVO3_PIN 4 // (RGB_LED_G_PIN)
//
// Limit Switches
//
#define X_MIN_PIN 63
#define X_MAX_PIN 64
#define Y_MIN_PIN 14
#define Y_MAX_PIN 15
#define Z_MIN_PIN 12
#define Z_MAX_PIN 9
#ifndef FIL_RUNOUT_PIN
#define FIL_RUNOUT_PIN SERVO2_PIN
#endif
//
// Z Probe (when not Z_MIN_PIN)
//
#ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN 9 // Servos pin
#endif
//
// Steppers
//
#define X_STEP_PIN 54
#define X_DIR_PIN 55
#define X_ENABLE_PIN 38
#ifndef X_CS_PIN
#define X_CS_PIN 70
#endif
#define Y_STEP_PIN 60
#define Y_DIR_PIN 61
#define Y_ENABLE_PIN 56
#ifndef Y_CS_PIN
#define Y_CS_PIN 39
#endif
#define Z_STEP_PIN 43
#define Z_DIR_PIN 48
#define Z_ENABLE_PIN 58
#ifndef Z_CS_PIN
#define Z_CS_PIN 74
#endif
#define E0_STEP_PIN 26
#define E0_DIR_PIN 28
#define E0_ENABLE_PIN 24
#ifndef E0_CS_PIN
#define E0_CS_PIN 47
#endif
#define E1_STEP_PIN 36
#define E1_DIR_PIN 34
#define E1_ENABLE_PIN 30
#ifndef E1_CS_PIN
#define E1_CS_PIN 32
#endif
#define E2_STEP_PIN 59
#define E2_DIR_PIN 57
#define E2_ENABLE_PIN 40
#ifndef E2_CS_PIN
#define E2_CS_PIN 42
#endif
//
// Sensorless homing DIAG pin is not directly connected to the MCU. Close
// the jumper next to the limit switch socket when using sensorless homing.
//
#if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209)
// Software serial
// At the moment, F6 rx pins are not pc interrupt pins
#define X_SERIAL_RX_PIN -1 // 71
#define X_SERIAL_TX_PIN 72
#define Y_SERIAL_RX_PIN -1 // 73
#define Y_SERIAL_TX_PIN 75
#define Z_SERIAL_RX_PIN -1 // 78
#define Z_SERIAL_TX_PIN 79
#define E0_SERIAL_RX_PIN -1 // 76
#define E0_SERIAL_TX_PIN 77
#define E1_SERIAL_RX_PIN -1 // 80
#define E1_SERIAL_TX_PIN 81
#define E2_SERIAL_RX_PIN -1 // 22
#define E2_SERIAL_TX_PIN 82
#endif
//
// Temperature Sensors
//
#define TEMP_0_PIN 12 // Analog Input
#define TEMP_1_PIN 13 // Analog Input
#define TEMP_2_PIN 14 // Analog Input
#define TEMP_BED_PIN 15 // Analog Input
#ifndef FILWIDTH_PIN
#define FILWIDTH_PIN 9 // Analog Input on X+ endstop
#endif
//
// Heaters / Fans
//
#define HEATER_0_PIN 5
#define HEATER_1_PIN 6
#define HEATER_2_PIN 7
#define HEATER_BED_PIN 8
#define FAN_PIN 44
#define FAN1_PIN 45
#define FAN2_PIN 46
//
// Misc. Functions
//
#define SDSS 53
#define LED_PIN 13
#define KILL_PIN 41
#ifndef PS_ON_PIN
#define PS_ON_PIN SERVO1_PIN
#endif
/**
* ----- -----
* 5V/D41 | · · | GND 5V | · · | GND
* RESET | · · | D49 (SD_DETECT) (LCD_D7) D29 | · · | D27 (LCD_D6)
* (MOSI) D51 | · · | D33 (BTN_EN2) (LCD_D5) D25 | · · | D23 (LCD_D4)
* (SD_SS) D53 | · · | D31 (BTN_EN1) (LCD_RS) D16 | · · | D17 (LCD_EN)
* (SCK) D52 | · · | D50 (MISO) (BTN_ENC) D35 | · · | D37 (BEEPER)
* ----- -----
* EXP2 EXP1
*/
//
// LCDs and Controllers
//
#define BEEPER_PIN 37
#define SD_DETECT_PIN 49
#if ENABLED(FYSETC_MINI_12864)
//
// See https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8
//
#define DOGLCD_A0 16
#define DOGLCD_CS 17
#define LCD_BACKLIGHT_PIN -1
#define KILL_PIN 41
#define LCD_RESET_PIN 23 // Must be high or open for LCD to operate normally.
// Seems to work best if left open.
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN 25
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN 27
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN 29
#endif
#elif ENABLED(FYSETC_MINI_12864_2_1)
#define NEOPIXEL_PIN 25
#endif
#elif HAS_GRAPHICAL_LCD
#define LCD_PINS_RS 16
#define LCD_PINS_ENABLE 17
#define LCD_PINS_D4 23
#define LCD_PINS_D5 25
#define LCD_PINS_D6 27
#define LCD_PINS_D7 29
#if ENABLED(MKS_MINI_12864)
#define DOGLCD_CS 25
#define DOGLCD_A0 27
#endif
#endif
#if ENABLED(NEWPANEL)
#define BTN_EN1 31
#define BTN_EN2 33
#define BTN_ENC 35
#endif
#ifndef RGB_LED_R_PIN
#define RGB_LED_R_PIN 3
#endif
#ifndef RGB_LED_G_PIN
#define RGB_LED_G_PIN 4
#endif
#ifndef RGB_LED_B_PIN
#define RGB_LED_B_PIN 9
#endif
#ifndef RGB_LED_W_PIN
#define RGB_LED_W_PIN -1
#endif