You cannot select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
288 lines
7.4 KiB
C
288 lines
7.4 KiB
C
/**
|
|
* Marlin 3D Printer Firmware
|
|
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
|
|
*
|
|
* Based on Sprinter and grbl.
|
|
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 3 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*
|
|
*/
|
|
#pragma once
|
|
|
|
#ifndef TARGET_LPC1768
|
|
#error "Oops! Make sure you have the LPC1768 environment selected in your IDE."
|
|
#endif
|
|
|
|
#ifndef BOARD_NAME
|
|
#define BOARD_NAME "BIGTREE SKR V1.3"
|
|
#endif
|
|
|
|
// Ignore temp readings during develpment.
|
|
//#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE
|
|
|
|
//
|
|
// Servos
|
|
//
|
|
#define SERVO0_PIN P2_00
|
|
|
|
//
|
|
// Limit Switches
|
|
//
|
|
#define X_MIN_PIN P1_29
|
|
#define X_MAX_PIN P1_28
|
|
#define Y_MIN_PIN P1_27
|
|
#define Y_MAX_PIN P1_26
|
|
#define Z_MIN_PIN P1_25
|
|
#define Z_MAX_PIN P1_24
|
|
|
|
//
|
|
// Z Probe (when not Z_MIN_PIN)
|
|
//
|
|
#ifndef Z_MIN_PROBE_PIN
|
|
#define Z_MIN_PROBE_PIN P1_24
|
|
#endif
|
|
|
|
//
|
|
// Filament Runout Sensor
|
|
//
|
|
#ifndef FIL_RUNOUT_PIN
|
|
#define FIL_RUNOUT_PIN P1_28
|
|
#endif
|
|
|
|
//
|
|
// Steppers
|
|
//
|
|
#define X_STEP_PIN P2_02
|
|
#define X_DIR_PIN P2_06
|
|
#define X_ENABLE_PIN P2_01
|
|
#ifndef X_CS_PIN
|
|
#define X_CS_PIN P1_17
|
|
#endif
|
|
|
|
#define Y_STEP_PIN P0_19
|
|
#define Y_DIR_PIN P0_20
|
|
#define Y_ENABLE_PIN P2_08
|
|
#ifndef Y_CS_PIN
|
|
#define Y_CS_PIN P1_15
|
|
#endif
|
|
|
|
#define Z_STEP_PIN P0_22
|
|
#define Z_DIR_PIN P2_11
|
|
#define Z_ENABLE_PIN P0_21
|
|
#ifndef Z_CS_PIN
|
|
#define Z_CS_PIN P1_10
|
|
#endif
|
|
|
|
#define E0_STEP_PIN P2_13
|
|
#define E0_DIR_PIN P0_11
|
|
#define E0_ENABLE_PIN P2_12
|
|
#ifndef E0_CS_PIN
|
|
#define E0_CS_PIN P1_08
|
|
#endif
|
|
|
|
#define E1_STEP_PIN P0_01
|
|
#define E1_DIR_PIN P0_00
|
|
#define E1_ENABLE_PIN P0_10
|
|
#ifndef E1_CS_PIN
|
|
#define E1_CS_PIN P1_01
|
|
#endif
|
|
|
|
//
|
|
// Software SPI pins for TMC2130 stepper drivers
|
|
//
|
|
#if ENABLED(TMC_USE_SW_SPI)
|
|
#define TMC_SW_MOSI P4_28
|
|
#define TMC_SW_MISO P0_05
|
|
#define TMC_SW_SCK P0_04
|
|
#endif
|
|
|
|
#if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209)
|
|
/**
|
|
* TMC2208/TMC2209 stepper drivers
|
|
*
|
|
* Hardware serial communication ports.
|
|
* If undefined software serial is used according to the pins below
|
|
*/
|
|
//#define X_HARDWARE_SERIAL Serial
|
|
//#define X2_HARDWARE_SERIAL Serial1
|
|
//#define Y_HARDWARE_SERIAL Serial1
|
|
//#define Y2_HARDWARE_SERIAL Serial1
|
|
//#define Z_HARDWARE_SERIAL Serial1
|
|
//#define Z2_HARDWARE_SERIAL Serial1
|
|
//#define E0_HARDWARE_SERIAL Serial1
|
|
//#define E1_HARDWARE_SERIAL Serial1
|
|
//#define E2_HARDWARE_SERIAL Serial1
|
|
//#define E3_HARDWARE_SERIAL Serial1
|
|
//#define E4_HARDWARE_SERIAL Serial1
|
|
|
|
//
|
|
// Software serial
|
|
//
|
|
#define X_SERIAL_TX_PIN P4_29
|
|
#define X_SERIAL_RX_PIN P1_17
|
|
|
|
#define Y_SERIAL_TX_PIN P1_16
|
|
#define Y_SERIAL_RX_PIN P1_15
|
|
|
|
#define Z_SERIAL_TX_PIN P1_14
|
|
#define Z_SERIAL_RX_PIN P1_10
|
|
|
|
#define E0_SERIAL_TX_PIN P1_09
|
|
#define E0_SERIAL_RX_PIN P1_08
|
|
|
|
#define E1_SERIAL_TX_PIN P1_04
|
|
#define E1_SERIAL_RX_PIN P1_01
|
|
|
|
#define Z2_SERIAL_TX_PIN P1_04
|
|
#define Z2_SERIAL_RX_PIN P1_01
|
|
|
|
#endif
|
|
|
|
//
|
|
// Temperature Sensors
|
|
// 3.3V max when defined as an analog input
|
|
//
|
|
#define TEMP_BED_PIN 0 // A0 (T0) - (67) - TEMP_BED_PIN
|
|
#define TEMP_0_PIN 1 // A1 (T1) - (68) - TEMP_0_PIN
|
|
#define TEMP_1_PIN 2 // A2 (T2) - (69) - TEMP_1_PIN
|
|
|
|
//
|
|
// Heaters / Fans
|
|
//
|
|
#define HEATER_0_PIN P2_07
|
|
#if HOTENDS == 1
|
|
#define FAN1_PIN P2_04
|
|
#else
|
|
#define HEATER_1_PIN P2_04
|
|
#endif
|
|
#define FAN_PIN P2_03
|
|
#define HEATER_BED_PIN P2_05
|
|
|
|
/**
|
|
* _____ _____
|
|
* NC | · · | GND 5V | · · | GND
|
|
* RESET | · · | 1.31(SD_DETECT) (LCD_D7) 1.23 | · · | 1.22 (LCD_D6)
|
|
* (MOSI)0.18 | · · | 3.25(BTN_EN2) (LCD_D5) 1.21 | · · | 1.20 (LCD_D4)
|
|
* (SD_SS)0.16 | · · | 3.26(BTN_EN1) (LCD_RS) 1.19 | · · | 1.18 (LCD_EN)
|
|
* (SCK)0.15 | · · | 0.17(MISO) (BTN_ENC) 0.28 | · · | 1.30 (BEEPER)
|
|
* ----- -----
|
|
* EXP2 EXP1
|
|
*/
|
|
#if HAS_SPI_LCD
|
|
#define BEEPER_PIN P1_30 // (37) not 5V tolerant
|
|
#define BTN_ENC P0_28 // (58) open-drain
|
|
|
|
#if ENABLED(CR10_STOCKDISPLAY)
|
|
#define LCD_PINS_RS P1_22
|
|
|
|
#define BTN_EN1 P1_18
|
|
#define BTN_EN2 P1_20
|
|
|
|
#define LCD_PINS_ENABLE P1_23
|
|
#define LCD_PINS_D4 P1_21
|
|
|
|
#else
|
|
#define LCD_PINS_RS P1_19
|
|
|
|
#define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
|
|
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
|
|
|
|
#define LCD_PINS_ENABLE P1_18
|
|
#define LCD_PINS_D4 P1_20
|
|
|
|
#define LCD_SDSS P0_16 // (16) J3-7 & AUX-4
|
|
#define SD_DETECT_PIN P1_31 // (49) (NOT 5V tolerant)
|
|
|
|
#if ENABLED(FYSETC_MINI_12864)
|
|
#define DOGLCD_CS P1_18
|
|
#define DOGLCD_A0 P1_19
|
|
#define DOGLCD_SCK P0_15
|
|
#define DOGLCD_MOSI P0_18
|
|
#define FORCE_SOFT_SPI
|
|
|
|
#define LCD_BACKLIGHT_PIN -1
|
|
|
|
#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems
|
|
// results in LCD soft SPI mode 3, SD soft SPI mode 0
|
|
|
|
#define LCD_RESET_PIN P1_20 // Must be high or open for LCD to operate normally.
|
|
|
|
#if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0)
|
|
#ifndef RGB_LED_R_PIN
|
|
#define RGB_LED_R_PIN P1_21
|
|
#endif
|
|
#ifndef RGB_LED_G_PIN
|
|
#define RGB_LED_G_PIN P1_22
|
|
#endif
|
|
#ifndef RGB_LED_B_PIN
|
|
#define RGB_LED_B_PIN P1_23
|
|
#endif
|
|
#elif ENABLED(FYSETC_MINI_12864_2_1)
|
|
#define NEOPIXEL_PIN P1_21
|
|
#endif
|
|
|
|
#else // !FYSETC_MINI_12864
|
|
|
|
#if ENABLED(MKS_MINI_12864)
|
|
#define DOGLCD_CS P1_21
|
|
#define DOGLCD_A0 P1_22
|
|
#endif
|
|
|
|
#if ENABLED(ULTIPANEL)
|
|
#define LCD_PINS_D5 P1_21
|
|
#define LCD_PINS_D6 P1_22
|
|
#define LCD_PINS_D7 P1_23
|
|
#endif
|
|
|
|
#endif // !FYSETC_MINI_12864
|
|
|
|
#endif
|
|
|
|
#endif // HAS_SPI_LCD
|
|
|
|
//
|
|
// SD Support
|
|
//
|
|
|
|
#ifndef SDCARD_CONNECTION
|
|
#define SDCARD_CONNECTION LCD
|
|
#endif
|
|
|
|
#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card
|
|
|
|
#if SD_CONNECTION_IS(LCD)
|
|
#define SCK_PIN P0_15
|
|
#define MISO_PIN P0_17
|
|
#define MOSI_PIN P0_18
|
|
#define SS_PIN P0_16
|
|
#elif SD_CONNECTION_IS(ONBOARD)
|
|
#undef SD_DETECT_PIN
|
|
#define SD_DETECT_PIN P0_27
|
|
#define SCK_PIN P0_07
|
|
#define MISO_PIN P0_08
|
|
#define MOSI_PIN P0_09
|
|
#define SS_PIN ONBOARD_SD_CS_PIN
|
|
#elif SD_CONNECTION_IS(CUSTOM_CABLE)
|
|
#error "No custom SD drive cable defined for this board."
|
|
#endif
|
|
|
|
/**
|
|
* Special pins
|
|
* P1_30 (37) (NOT 5V tolerant)
|
|
* P1_31 (49) (NOT 5V tolerant)
|
|
* P0_27 (57) (Open collector)
|
|
* P0_28 (58) (Open collector)
|
|
*/
|