ac4f235912
Merge pull request #4167 from thinkyhead/rc_eeprom_checksum
...
EEPROM Checksum
8 years ago
03b8f88092
Tab to Space
8 years ago
cb1b31f69b
Unconditional do_probe_raise() in probe_pt()
...
If Z_RAISE_BETWEEN_PROBINGS is null or undefined the probe is currently not raised by home_offset[Z_AXIS] and zprobe_zoffset.
But when different from 0 is.
If an undefined Z_RAISE_BETWEEN_PROBINGS expands to 0 (and it does) this is the solution.
A similar asymmetry exists with the newly introduced 'short-cut' in G28 - but its the rise before anything is probed - so should not make a difference.
8 years ago
7ef7843fd4
Merge pull request #4181 from thinkyhead/rc_rename_a_move_func
...
Do interpolated moves for Allen Key deploy/stow
8 years ago
6b2a7b30af
Extra comments to clarify EEPROM code
8 years ago
787f394676
MAX_EXTRUDERS replaces mysterious "4"
8 years ago
bc3748b7bc
Add shared Config_Postprocess for Read and Reset
8 years ago
adcd0f5de3
Some formatting in configuration_store.cpp
8 years ago
5e370006fc
EEPROM Checksum
8 years ago
725fde8b26
Merge pull request #4169 from thinkyhead/rc_wait_but_break
...
Allow wait-for-cooling, break at threshold or if cooling stalls
8 years ago
da6b0dab5f
Use prepare_move_to_destination for Allen Key deploy/stow
8 years ago
c42f8fb8dd
Rename some movement sub-functions
8 years ago
b6b3a4afbf
Merge pull request #4168 from thinkyhead/rc_viki2_for_ramps
...
Support for VIKI2 in RAMPS and derivatives
9 years ago
f84d85f761
Cleanup extruder runout configs
9 years ago
5e14a528dd
Always wait for cooling in M109/M190, break at low temp or if cooling stalls
9 years ago
0b0b7aac6e
Support for VIKI2 in RAMPS and derivatives
9 years ago
abda4ab427
Clean up CNControls pins
9 years ago
683975cf90
Fix spelling in a config comment
9 years ago
8268c0a9a0
Always define temp sensor, heater pins for RUMBA
9 years ago
db19959735
Merge pull request #4161 from thinkyhead/rc_general_cleanup
...
Reduce storage requirements for strings, make some PGM
9 years ago
2e96276bf4
More debug message cleanup
9 years ago
dc2c0e5e24
Simpler debug output for deploy/stow
9 years ago
bd491818d6
Reduce storage requirements for strings, make some PGM
9 years ago
ee876dcd7a
Merge pull request #4159 from thinkyhead/rc_rigidbot_diff
...
Rigidbot V2 support - has MCP4728 digipot
9 years ago
0c24e0e445
Support for newer Wire library
9 years ago
ddb386c139
Init DAC_DISABLE_PIN in dac_init
9 years ago
e480ee0054
Further cleanup of G28 for probes
9 years ago
39883d03fc
universalize axis_unhomed_error()
9 years ago
e616093d4c
Simplify dock_sled()
...
`dock_sled()` is never called with offset parameter - remove it.
We move x only - so only that needs to be homed. Consequence is - we can home to z-min now with a sled probe!
Feedrates are set and restored in `do_blocking_move()`.
We already checked if the probe is deployed/stowed in deploy/stow_probe.
```
if (z_loc < _Z_RAISE_PROBE_DEPLOY_STOW + 5) z_loc = _Z_RAISE_PROBE_DEPLOY_STOW;
```
makes no sense - remove.
Now the raise is the same for deploy/stow -> move before the if.
Replace the if with a ternary.
Instead writing LOW/HIGH use the boolean `stow` we already have.
There is no reason for not using the sled probe in G29/M48 with 'E'.
It takes a while but works. (tested!)
9 years ago
6c60869409
Support DAC_OR_ADDRESS in Printrboard too
9 years ago
593c8bf286
Support for Rigidbot V2
9 years ago
511503ede9
CARTESIO_UI has lcd contrast
9 years ago
829c92f1ba
Use Z_RAISE_BETWEEN_PROBINGS with MBL
9 years ago
eb1755208f
Merge pull request #4153 from thinkyhead/rc_probe_raise_options
...
Combine Z raise before/after options
9 years ago
10da7ac86c
Combine Z raise before/after options
9 years ago
9caa8941e2
Merge pull request #4149 from thinkyhead/rc_minimum_raise_in_probe_pt
...
Ensure a minimum height before XY move in probe_pt
9 years ago
3fa631130f
Ensure a minimum height before XY move in probe_pt
9 years ago
a7684eef7a
Squish code in ST7920
9 years ago
b4076883cc
Set testet delays for K8200, RAMBO, MINIRAMBO and ST7920
9 years ago
4454d80276
Decrease the needed nops to 1
...
by shitfing the left shift into the high phase.
```
2 cbi 0x2,1 ;set CLK //
1 in r18,__SREG__ //1
1-3 sbrc r24,7 //2-4
2 rjmp .L19 //4
1 cli .L19: //5
2 lds r25,258 lds r25,258 //7
1 andi r25,lo8(-2) ori r25,lo8(1) //8
2 sts 258,r25 sts 258,r25 //10
1 out __SREG__,r18 out __SREG__,r18 //11
2 .L3: rjmp .L3 //13 //2
2 sbi 0x2,1 ;reset CLK // //13-15 //2-4
1 lsl r24 ; val //1
1 nop //2
2 cbi 0x2,1 ;set CLK //4
...
```
9 years ago
56c42b572c
3 ms speedup for ST7920 and delay for BOARD_3DRAG
...
and saving ~1k memory
by limiting the `#pragma GCC optimize (3)` optimisation to `ultralcd_st7920_u8glib_rrd.h`. These optimisation was and is not done for all the other displays, is the reason for the big additionally use of memory, because the complete 'ultralcd.cpp' and 'dogm_lcd_implementation.h' was optimised (sadly i did not observe a change in speed).
Unrolling the loop in `ST7920_SWSPI_SND_8BIT()`, what i expected the optimiser to do, by hand, saved some speed by eliminating the loop variable (i) compares and increases. Every CPU cycle in this loop costs at least 0.5ms per display update because it's executed more than 1k times/s.
The delays are now pre-filled with the calculated values for 4.5V driven ST7920.
A way to simply add __your__ timing into the configuration was made.
At 4.5V
1.) The CLK signal needs to be at least 200ns high and 200ns low.
2.) The DAT pin needs to be set at least 40ns before CLK goes high and must stay at this value until 40ns after CLK went high.
A nop takes one processor cycle.
For 16MHz one nop lasts 62.5ns.
For 20MHz one not lasts 50ns.
To fulfill condition 1.) we need 200/62.5 = 3.2 => 4 cycles (200/50 = 4 => 4). For the low phase, setting the pin takes much longer. For the high phase we (theoretically) have to throw in 2 nops, because changing the CLK takes only 2 cycles.
Condition 2.) is always fulfilled because the processor needs two cycles (100 - 125ns) for switching the CLK pin.
Needs tests and feedback.
Especially i cant test 20MHz, 3DRAG and displays supplied wit less than 5V.
Are the delays right? Please experiment with longer or shorter delays. And give feedback.
Already tested are 5 displays with 4.9V - 5.1V at 16MHz where no delays are needed.
9 years ago
ca184d3d72
Merge pull request #4147 from thinkyhead/rc_fix_M48_raise
...
Fix debug output in probe_pt
9 years ago
b4161cbd98
Fix debug output in probe_pt
9 years ago
da88b00585
MBL: Add support for max z endstop
...
See https://github.com/MarlinFirmware/Marlin/issues/4088
9 years ago
74878d1f16
Always do a brief delay in `lcd_quick_feedback`
9 years ago
7de7552069
Merge pull request #4133 from MagoKimbra/Single_home_axis_delta
...
Single home Axis Delta need simple sync_plan_position
9 years ago
15a6b49f37
Simplified probe_pt (in G30)
9 years ago
6a7045b9bf
Remove clean_up_after_endstop_move
9 years ago
2a4f866561
Simplified probe_pt (in G29)
9 years ago
89a2aa026b
Simplified probe_pt (in M48)
9 years ago
f8530c5d1f
Simplified probe_pt function (G28 grid)
9 years ago
c376c08042
Simplified probe_pt function (part 1)
9 years ago
9a71b7f8ad
Fix debug message for 3-point leveling
9 years ago
550c03a5a9
Drop raise_z_after_probing function
9 years ago
bb38c816af
Always raise in deploy_z_probe / stow_z_probe
9 years ago
68f3350050
Cleanup M401 / M402
9 years ago
3afda99adf
Regular handlers for G31 / G32
9 years ago
6803c8e37e
Move Z up before, or down after XY, for "blocking move"
9 years ago
03c70c1990
SERVO_DEACTIVATION_DELAY => SERVO_DELAY
9 years ago
570f3bbc07
Single home Axis Delta need simple sync_plan_position
9 years ago
61f34eec03
Merge pull request #4125 from jbrazio/bugfix/planner-warning
...
Fixes some compiler warnings
9 years ago
bdcd628896
Merge pull request #4126 from thinkyhead/rc_lin_timing_patch
...
Patch LIN_ADVANCE timing issue
9 years ago
664232140d
Fixes somes compiler warnings
9 years ago
0c5192b288
Patch LIN_ADVANCE timing issue
...
Also the extruder stepper ISR has to keep an eye on step_loops count.
9 years ago
d4134e6901
Define Z_SAFE_HOMING point when Z_PROBE_SLED is activated alone
9 years ago
7b2fadd598
Apply some fixes from Andreas
...
Derived from
https://github.com/AnHardt/Marlin/commit/6e8ede8c694fa4d9e3c769840b09d56
7f8d8e0dd
9 years ago
bd01592816
Goodbye MECHANICAL_PROBE
9 years ago
2640d13a9f
Simplify initial raise in M48
9 years ago
3763d45656
Return Z position in run_z_probe
9 years ago
1f48b5c30f
Pass a raise to probe_pt, not a Z position
9 years ago
6fdd5ba246
Save and restore feedrate in more places
9 years ago
fe173c2bc6
Generalized probe raise, use for after probing
9 years ago
7da3080761
Simpler cleanup in G28 / G29
9 years ago
15229d988b
Fix compile error for bed matrix in M48
9 years ago
c01352cbd5
Add a dependency for z servo macros
9 years ago
c3794bd695
Add HAS_PROBING_PROCEDURE conditional
9 years ago
42ce60c5cc
Make sure NUM_SERVOS is set for Z servo endstop
9 years ago
b590a7dee0
Make Z_RAISE_BETWEEN_PROBINGS a more general option
9 years ago
bb9c67b4b5
Tweak some feedrate vars
9 years ago
5158bd6e93
Screen out `G29 E` for sled and allen key, allow single probe
9 years ago
ccae92588d
Cleanup debug in G28 and G29
9 years ago
b4a9d2366c
Use a macro for kinematic sync_plan_position
9 years ago
bfccf26294
Use sync_plan_position_delta where needed
9 years ago
a6b8c67df4
Move probe deploy after setup call in G29
9 years ago
e69916d1bd
Split up endstop_move functions
9 years ago
0e18a4897b
Simpler handling of sled/allen-key in probe_pt
9 years ago
1a92e2ef18
Comment on run_z_probe
9 years ago
68e0e5855e
For all probes, at the end of G29 simply raise and stow
9 years ago
c3023f8cc5
Make M401/M402 available with HAS_BED_PROBE
9 years ago
9f0c255c69
Show uncorrected position in set_bed_level_equation_3pts
9 years ago
07298ac992
Initialize current_position to home_offset on boot
9 years ago
d50539583a
Make XY_PROBE_SPEED a general probe option
9 years ago
2798499b71
XY_TRAVEL_SPEED => XY_PROBE_SPEED
9 years ago
88dc543584
Add a macro for XY_TRAVEL_FEEDRATE
9 years ago
117db77c55
make motor_current_setting static and constexpr
9 years ago
19fb04d761
Update bq Hephestos 2 config
9 years ago
b0e47608e6
Merge pull request #4108 from esenapaj/Fix-for-PR-#4093
...
Fix for PR #4093 (Make Z Probe options independent of ABL), etc
9 years ago
c84732e605
Merge pull request #4111 from esenapaj/Cosmetic-changes-and-small-fix-for-thermistortables.h
...
Cosmetic changes and small fix for thermistortables.h
9 years ago
cdc661ea5e
Merge pull request #4110 from esenapaj/Small-cosmetic-changes-for-language-files
...
Small cosmetic changes for language files
9 years ago
c8186e9423
Merge pull request #4109 from esenapaj/Enclose-#error-string-by-double-quotes
...
Enclose #error string by double-quotes
9 years ago
Scott Lahteine